Home
        Bloomfield B-406 Toaster User Manual
         Contents
1.                        nS eee  WELLS BLOOMFIELD  LLC 1 6 2  2 ERIK CIRCLE  P  O  Box 280 Verdi  NV 89439  telephone  775 689 5703  fax  775 689 5976  www wellsbloomfield com    OPERATION  MANUAL    for    BUILT IN  ELECTRIC  CHAR   Model B 406 k BROILERS    Models   B 406  B 446  B 506        includes   INSTALLATION   Model B 446 USE and CARE       IMPORTANT  DO NOT DISCARD THIS MANUAL  This manual is considered to be part of the appliance and is to be given to the OWNER or  MANAGER of the restaurant  or to the person responsible for TRAINING OPERATORS of  this appliance  Additional manuals are available from your WELLS DEALER     THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR    INSTALLING THIS APPLIANCE  Contact your WELLS DEALER if you have any  questions concerning installation  operation or maintenance of this equipment     PRINTED IN UNITED STATES OF AMERICA    p n 303673 Rev D ECN 13371 M162 071025 cps    Unless otherwise specified  all commercial cooking  equipment manufactured by WELLS BLOOMFIELD  LLC is  warranted against defects in materials and workmanship for  a period of one year from the date of original installation or  18 months from the date of shipment from our factory   whichever comes first  and is for the benefit of the original  purchaser only    THIS WARRANTY IS THE COMPLETE AND ONLY  WARRANTY  EXPRESSED OR IMPLIED IN LAW OR IN  FACT  INCLUDING BUT NOT LIMITED TO  WARRANTIES  OF MERCHANTABILITY OR FITNESS FOR ANY  PARTICULAR PURPOSE  A
2.         LO    is the lowest temperature settings  Use LO for stand by operation        2    thru    8    are temperature settings  Higher number indicate higher  temperature        HI    is a continuous ON setting  Use HI for pre heating the broiler   USING THE CHAR BROILER    Pre Heat the broiler ten  10  minutes by turning the TEMPERATURE  CONTROL to    HI        After the pre heat period  turn the TEMPERATURE CONTROL to the  desired setting  refer to the Broiler Chart at right for recommended  settings      After every order  use the brush provided to brush any remaining food  particles from grate and elements  Keeping the cooking surfaces clean  will help in maintaining food taste     Visually check the water level in the drip pan during operation  Add  water as required to maintain 2 inches  5cm  water depth in the drip  pan     suapjoiqueyD 94499  Uj yiNg 104  enueWdO EZ9EOE Z914    162 303673 OpManual for Built In Electric Charbroilers    BROILER CHART  RECOMMENDED COOKING TIMES AND DIAL SETTINGS    NOTE  The times and dial settings in this chart are suggestions only  Your own  experience with your own menu items will be your best guide to achieving the best food  product     PRODUCT THICKNESS COOKING DIAL TIME  Condition SETTING Minutes Total    Le  o f e  BEEF Non Frozen  De  a     gt   D    N  1  o       SYMPTON POSSIBLE CAUSE SUGGESTED REMEDY  Won t heat    no indicator Electric disconnect OFF Check   turn disconnect ON  lights Circuit breaker tripped Check   reset
3.  6  Full use  care  and maintenance instructions supplied  with each machine  Noted maintenance and  preventative maintenance items  such as servicing and    NOTE  For your protection  please note that equipment in  this shipment was carefully inspected and packaged by  skilled personnel before leaving the factory  Upon  acceptance of this shipment  the transportation company  assumes full responsibility for its safe delivery    IF SHIPMENT ARRIVES DAMAGED    1  VISIBLE LOSS OR DAMAGE  Be certain that any  visible loss or damage is noted on the freight bill or  express receipt  and that the note of loss or damage is  signed by the delivery person    2  FILE CLAIM FOR DAMAGE IMMEDIATELY   Regardless of the extent of the damage     based upon the limitations in this warranty  Seller   s  obligation under this warranty is limited to the repair of  defects without charge by a Wells Bloomfield factory  authorized service agency or one of its sub service  agencies  This service will be provided on customer s  premises for non portable models  Portable models  a  device with a cord and plug  must be taken or shipped to  the closest authorized service agency  transportation  charges prepaid  for service  In addition to restrictions  contained in this warranty  specific limitations are shown in  the Service Policy and Procedure Guide  Wells Bloomfield  authorized service agencies are located in principal cities   This warranty is valid in the United States and Canada and  void elsewhe
4.  Also voltage and  phase information  and agency approvals     The broiler is equipped with WELLSLOKS  uniquely designed turnout  tabs  which help secure the broiler to the countertop   See Installation  Instructions supplied with the particular appliance for details      162 303673 OpManual for Built In Electric Charbroilers         ELEMENT  ASSEMBLY    a ELEMENT    SUPPORT  ROD    IV SN K    K  i AEE  INDICATOR Ss  LIGHT            NS DATA  PLATE  TEMPERATURE  CONTROL    Fig  1 Built In Electric Charbroiler       WELLS    LOKS    7 x  A Kx  a SSN  LO Se SQ  A a SS SQ  LAA Za Ss       waa eS OS  AO OE    Se SL  EE SS  S  SEs    Fig  2 Wellsloks             WARNING   Electric Shock  Hazard    All servicing requiring access  to non insulated electrical  components must be  performed by a factory  authorized technician    DO NOT open any access  panel which require the use of  tools  Failure to follow this  warning can result in severe  electrical shock     CAUTION   Risk of Damage    DO NOT connect or energize  this appliance until all  installation instructions are  read and followed  Damage  to the appliance will result if  these instructions are not  followed        NSE  s24    Pe    E6070    Broilers are intended for use to cook food products for human  consumption  No other use is recommended or authorized by the  manufacturer or its agents     Broilers are intended for use in commercial establishments  where all  users are familiar with the appliance limitations  use and
5.  associated  hazards  Operating instruction and warnings must be read and  understood by all operators and users     Do not submerge broilers in water  Do not splash  or pour water onto  controls  control panels or wiring     Disconnect the broiler from electrical power before performing any  service or maintenance     Allow drip pan to cool before removing from broiler  Do not operate  broiler without the drip pan installed  Do not operate the broiler without  2    of water in the drip pan     Any parts replacement  maintenance procedure or servicing procedure  requiring the use of tools must be performed by an Authorized Service  Agency     Any troubleshooting guides  component view  parts lists or installation  guides provided with this equipment are intended for the use of the  qualified technical personnel only     Except where otherwise noted  this piece of equipment is made in the  USA and has American sizes on hardware     This manual should be considered a permanent part of this appliance   This manual and all supplied instructions  diagrams  schematics  parts  break downs  notices and labels must remain with the appliance if it  sold or moved to another location     This appliance conforms to NSF Standard 4 for sanitation only if  installed in accordance with the supplied Installation Instructions     This appliance is Underwriters Laboratory recognized   AN   Since  this appliance is only a single component of a complete installation  the  finished installation of 
6.  circuit breaker  One or more section Temperature control not set Set temperature control knob to  won   t heat   or not hot desired temperature  enough  240V unit run on 208V Verify proper voltage    Damaged component or wiring Contact an Authorize Wells    Service Agency for repairs    One or more section too Temperature control not set Set temperature control knob to  hot desired temperature  208V unit run on 240V Verify proper voltage    Damaged component or wiring Contact an Authorized Wells  Service Agency for repairs   Element assy loose  or Damaged hinge Contact an Authorized Wells  difficult to raise or lower  see page 7 for precautions  Service Agency for repairs   Element assy does not Damaged support rod assembly Contact an Authorized Wells  latch in up position Service Agency for repairs    NOTE  There are no user  serviceable components in  this appliance  In all cases of  damage or component  malfunction  contact your  Authorized Wells Service  Agency for repairs        SJ  JOIQIEYO 94498 F Uj WINg 104 fenUepdO EZ9E0E Z94    162 303673 OpManual for Built In Electric Charbroilers    PREPARATION  Turn both temperature control knobs OFF   Allow broiler to cool completely   Disconnect broiler from electric power     FREQUENCY  Daily     TOOLS  Steel Brush with Scraper  Plastic Scouring pad  Soft Bristled Fiber Brush  Mild Detergent  Non Abrasive Cleanser  Clean Soft Cloth   Sponge    CLEANING  1  Remove the grate from the broiler  Clean grate   a  Use the supplied 
7. ENT  ASSEMBLY    ELEMENT GUARD   GRATE    ELEMENT SUPPORT ROD    DRIP PAN    DATA PLATE    WELLSLOKS    COMMENT    The char broiler is INFINITE SWITCH CONTROLLED  Power is  applied to the heating elements based on the control knob position and  the amount of energy used     Light will glow when the infinite switch is in any position other that OFF     The char broiler element assembly may be raised for cleaning  or to  add water to the drip pan  It is held the    up    position by a support rod  which automatically engages as the element is raised     The grate is designed to protect the individual elements from food  contact and spatula abrasion  resulting in prolonged element life and  reduced carbonization  The grate is easily removed for cleaning     IMPORTANT  Always remove the grate before lifting the element  assembly     Hold element assembly in up position  Engages automatically when the  element assembly is raised     IMPORTANT  Remember to dis engage the support rod before  lowering element assembly    The heavy duty removable drip pan is located under the element    IMPORTANT  DO NOT pour water over elements to refill drip pan     SI  JOIQIEYO 9498 7 UI HING 104 fenUeWWdO EZ9E0E Z9I    assembly  The drip pan catches food particles and grease drippings  during broiler operation  Maintain 2 inches of water in the drip pan at all  times during operation of the broiler  The drip pan is easily removed for  cleaning     Gives manufacturer  make  model and serial number 
8. ND OR FOR DIRECT   INDIRECT OR CONSEQUENTIAL DAMAGES IN  CONNECTION WITH WELLS BLOOMFIELD PRODUCTS   This warranty is void if it is determined that  upon inspection  by an authorized service agency  the equipment has been  modified  misused  misapplied  improperly installed  or  damaged in transit or by fire  flood or act of God  It also  does not apply if the serial nameplate has been removed  or  if service is performed by unauthorized personnel  The  prices charged by Wells Bloomfield for its products are    1  Resetting of safety thermostats  circuit breakers  over  load protectors  and or fuse replacements are not  covered by this warranty unless warranted conditions  are the cause    2  All problems due to operation at voltages or phase  other than specified on equipment nameplates are  not covered by this warranty    Conversion to correct voltage and or phase must be  the customer s responsibility    3  All problems due to electrical connections not made  in accordance with electrical code requirements  and wiring diagrams supplied with the equipment are  not covered by this warranty    4  Replacement of items subject to normal wear  to  include such items as knobs  light bulbs  and  normal  maintenance functions including adjustments of  thermostats  adjustment of micro switches and  replacement of fuses and indicating lights are not  covered by warranty    5  Damage to electrical cords and or plug due to exposure  to excessive heat are not covered by this warranty   
9. TTOM  MOUNT    CAUTION   Hot Surface    Exposed surfaces can be hot  to the touch and may cause  burns   A  IMPORTANT  DO NOT  attempt to raise the element  assembly without first  removing the grate  Damage  to the hinges will result  Such  damage is NOT covered by  warranty   A  IMPORTANT  Allow drip pan  to cool before removing from  the broiler    DO NOT operate the broiler  without the drip pan installed   DO NOT operate the broiler  without 2     5cm  of water in  the drip pan   E  IMPORTANT  DO NOT  attempt to lower the element  assembly without first  releasing the support rod   Damage to the hinges will  result  Such damage is NOT  covered by warranty         Fig  6 B 44 and B 50 GRATE INSTALLATION       CAUTION   Hot Surface       Exposed surfaces  can be hot to the touch and  may cause burns                                   Fig  7 TEMPERATURE CONTROL    IMPORTANT  DO NOT  POUR WATER OVER  ELEMENTS TO REFILL  PAN    DO NOT splash or pour water  onto controls  control panels  or wiring        TEMPERATURE CONTROLS    Each section of the broiler is equipped with an individual temperature  control  The desired temperature is controlled by rotating the  TEMPERATURE CONTROL KNOB  Any time the control is turned     ON     the adjacent indicator light will glow  Each section of the broiler  may be set to a different temperature setting        OFF    removes power from the element   allowing the element to cool   Use OFF to turn the broiler off at the end of the cooking day
10. ers       PREPARE THE CHAR BROILER FOR USE    When using the broiler for the first  time  wipe the entire unit with a clean  damp cloth or sponge and mild    TA    detergent  Rinse thoroughly clean 5   water  Dry with a soft clean cloth  ELEMENT ASSY    SUPPORT ROD X   Remove the GRATE and raise the   SRELEA   ELEMENT ASSEMBLY  DRIP PAN  in place    Install the DRIP PAN and add G Yj   2     5cm  of tap water  Vi   Release the ELEMENT SUPPORT d   ROD by lifting the element assembly  amp   Jh     slightly  then pulling the lower portion  of the support rod forward  Lower the  ELEMENT ASSEMBLY gently     Fig  4 ELEMENT SUPPORT ROD    ELEMENT  MODEL B 406  Grate must be HANDLE  installed ABOVE elements   Install the GRATE  front edge first   The TANGS of the grate go DOWN  and point toward the FRONT  The  grooves on the underside of the  grate align with the elements  The  rear edge of the grate can be  lowered until it rests firmly on the  elements                    GRATE TANG  Fig  5 B 40 GRATE INSTALLATION    MODELS B 446 and B 506  Grate s   can be installed above or below the  elements    ABOVE  Gently lower grate over  elements  The end with flush tabs  goes toward the front    BELOW  Install one wing bolt in  each tab  The notch in the wing  rests on the lip of the drip pan  The  end with flush tabs must go toward  the front Adjust the wing bolts so  that   when the element assembly is  lowered  the top of the element is  1 4   6mm  below the top of the  grate fins     BO
11. ield com       PRINTED IN UNITED STATES OF AMERICA    
12. ion company or carrier immediately  and file     CONCEALED DAMAGE    claim with them  This  should be done within fifteen  15  days from the date  the delivery was made to you  Be sure to retain the  container for inspection     Wells Bloomfield cannot assume liability for damage or loss  incurred in transit  We will  however  at your request  supply  you with the necessary documents to support your claim     SuapOsQUeYO 94499 F Uj yING 104 fenueydC EZIEOE Z9L    162 303673 OpManual for Built In Electric Charbroilers    WARRANTY xX   SPECIFICATIONS 1   FEATURES  amp  OPERATING CONTROLS 2   PRECAUTIONS  amp  GENERAL INFORMATION 4 Proper installation  professional   AGENCY LISTING INFORMATION 4 operation and consistent  5  7  9    Thank you for purchasing this  Wells Bloomfield appliance     INSTALLATION maintenance of this appliance   OPERATION will ensure that it gives you the  BROILER CHART very best performance and a   TROUBLESHOOTING SUGGESTIONS 10 long  economical service life    CLEANING INSTRUCTIONS 11   PARTS  amp  SERVICE 13 This manual contains the   CUSTOMER SERVICE DATA 13 information needed to properly    install this appliance in a  manner which will ensure its  optimum performance       AMPSPERLEG3     PER LEG 3    NEUT   AMPS FIELD  MODEL ELEMENT VOLTS L2 L3 19 WIRING    saan       NOTE  Refer to appropriate Installation Instructions for equipment dimensions  cut out dimensions   clearances  etc     ITEM    TEMPERATURE CONTROL    INDICATOR LIGHT    HEATING ELEM
13. is NOT covered by  warranty        THIS PAGE BLANK    162 303673 OpManual for Built In Electric Charbroilers    12    162 303673 OpManual for Built In Electric Charbroilers    DESCRIPTION SERVICE IMPORTANT  Use only  PART NO  factory authorized service  GREASE PAN  B 446  1 PER UNIT  li gata  B 506  2 PER UNIT  20174 For factory authorized  service  or to order factory  GREASE PAN  B 406 20202 authorized replacement parts   contact your Wells authorized  GRATE  B 446  1 PER UNIT  service agency  or call   B 506  2 PER UNIT  21706 Wells Bloomfield  LLC  2 Erik Circle  GRATE  B 406 21707 P  O  Box 280    Verdi  NV 89439    BRUSH  BROILER 21708  Service Parts Dept   phone   775  689 5707    fax   775  689 5976    Service Parts Department can  supply you with the name and  telephone number of the  WELLS AUTHORIZED  SERVICE AGENCY   nearest you     CUSTOMER SERVICE DATA    please have this information available if calling for service  RESTAURANT LOCATION    INSTALLATION DATE TECHNICIAN  SERVICE COMPANY    ADDRESS                          STATE ZIP  TELEPHONE NUMBER   ee    EQUIPMENT MODEL NO   EQUIPMENT SERIAL NO     VOLTAGE   check one  0208 0240       Commercial Food Equipment Service Association    Wells Bloomfield proudly supports CFESA  Commercial Food Equipment Service Association    SERVICE TRAINING   QUALITY SERVICE       CUSTOMER SATISFACTION    WELLS BLOOMFIELD  LLC  2 ERIK CIRCLE  P  O  Box 280 Verdi  NV 89439  telephone  775 689 5703  fax  775 689 5976  www wellsbloomf
14. l knowledge  of all applicable electrical  codes  Failure can result in  personal injury and property       damage   eMM MOM  CAUTION   Electrical Shock  Hazard    The broiler must be  electrically grounded   Connect the terminal marked     GND    or          to a suitable  building ground     b e M uou  IMPORTANT  Contact a  licensed electrician to install  and connect electrical power  the broiler    Electrical installation must be  performed by a licensed  electrician in compliance with  all local ordinances and code  requirements   fl    IMPORTANT  Damage due  to being connected to the  wrong voltage or phase is  NOT covered by warranty     ELECTRCAL HOOK UP    Refer to the nameplate  Verify the electrical service power  Voltage  and phase must match the nameplate specifications  Connecting the  griddle to the wrong voltage can severely damage the unit or cause  noticeable decreased performance     Use copper wire suitable for a minimum of 90  C for electrical supply  connections     Broilers are factory wired three phase  3a   For single phase  19   wiring  refer to the wiring diagram attached to the broiler  Conversion to  1  must be performed by a licensed electrician     This broiler is not fused  Protect the circuit with properly sized fuses or  circuit breaker     An electrical disconnect must be installed readily accessible to the  operator of the broiler     suajjosqueyD 944997 Uj yINg 104 jenueWdO EZ9EOE Z914    162 303673 OpManual for Built In Electric Charbroil
15. re  Please consult your classified telephone  directory  your foodservice equipment dealer or contact     Service Department  Wells Bloomfield  LLC  P O  Box 280  Verdi  Nevada 89439  phone  775  689 5707 or fax  775  689 5976    for information and other details concerning warranty     cleaning schedules  are customer responsibility  Those  miscellaneous adjustments noted are customer  responsibility  Proper attention to preventative  maintenance and scheduled maintenance procedures  will prolong the life of the appliance    7  Travel mileage is limited to sixty  60  miles from an  Authorized Service Agency or one of its sub service  agencies    8  All labor shall be performed during regular working  hours  Overtime premium will be charged to the buyer    9  All genuine Wells replacement parts are warranted for  ninety  90  days from date of purchase on non   warranty equipment  This parts warranty is limited only  to replacement of the defective part s   Any use of  non genuine Wells parts completely voids any  warranty    10  Installation  labor  and job check outs are not  considered warranty and are thus not covered by this  warranty    11  Charges incurred by delays  waiting time or operating  restrictions that hinder the service technician   s ability to  perform service are not covered by warranty  This  includes institutional and correctional facilities     3  CONCEALED LOSS OR DAMAGE  if damage is  unnoticed until the merchandise is unpacked  notify the  transportat
16. s on the Wellsloks are  turned out to lock the broiler into the counter  see Fig  3    c  Apply a thin bead of food grade silicone sealant around the  flange to seal it to the counter     Refer to the  nstallation Instructions for required clearances  Maintain  required clearances between the appliance and adjacent combustible  and non combustible surfaces     Sufficient overhead clearance must be provided to allow the element  assembly to be raised  Refer to the  nstallation Instruction Sheet for  required clearances     Install drip pan and element guard grate prior to heating or using broiler     Avoid storing flammable or combustible materials near the appliance     This includes gasoline and other fuels  mops  rags and wrapping paper     NOTE  DO NOT discard   the carton or other packing  materials until you have  inspected the appliance for  hidden damage and tested it  for proper operation    Refer to SHIPPING DAMAGE  CLAIM PROCEDURE on the  inside front cover of this  manual     IMPORTANT  This is a  GENERAL GUIDE  For  specific equipment and cutout  dimensions  and other  installation details  refer to  the  nstallation Instructions  supplied with the broilers        Fig  3 Set the Wellslloks    IMPORTANT  Water  damage caused by failure to  set Wellsloks  failure to install  gasket  or failure to seal  flange to counter is NOT  covered by warranty     WARNING    Risk of personal  injury   Installation procedures must  be performed by a qualified  technician with ful
17. steel brush with scraper to remove food  particles and residue from grate surfaces   b  Grate may be washed in sink or dishwasher   c  Dry the grate and apply a light coating of cooking oil     2  Raise the element assembly until it latches  Remove and clean    the drip pan   a  Stubborn food particles maybe removed with a plastic scouring  pad     b  Drip pan may be washed in a sink or dishwasher     3  Clean the element assembly   a  Use a soft bristled fiber brush to remove any remaining food  particles from the elements   b  Clean the element rods with a soft damp cloth or sponge and  mild detergent  Rinse by wiping with a soft cloth moistened  with clean water  Dry with a soft cloth     4  Clean the control panel with a soft damp cloth or sponge and mild  detergent  Rinse by wiping with a soft damp cloth moistened with  clean water  Dry with a soft cloth     5  Reassemble broiler   a  Reinstall drip pan   b  Unlatch element support rod and carefully lower the element  assembly   c  Reinstall the grate     Procedure complete     11       CAUTION   Electric Shock  Hazard    Disconnect appliance from  electric power before   cleaning   E    CAUTION   Burn Hazard    Allow appliance to cool  completely before cleaning   eee    CAUTION   Electric Shock  Hazard    Do not submerge appliance  in water   D  IMPORTANT    DO NOT spill or pour water  into controls  control panel or  wiring  Damage to internal  components will occur   Damage to internal  components from water  damage 
18. this unit YAY requires additional evaluations to    Underwriters Laboratory standards     Refer to Installation Instructions included with the broiler for  Underwriters Laboratories conditions of acceptability  electrical    suapjoiqueyO 94499  Uj yiNg 104  enueWdC EZ9EOE Z914    162 303673 OpManual for Built In Electric Charbroilers    UNPACKING  amp  INSPECTION    Carefully remove the appliance from the carton  Remove all protective  plastic film  packing materials and accessories from the appliance  before connecting electrical power or otherwise performing any  installation procedure     Carefully read all instructions in this manual and the  nstallation  Instruction Sheet packed with the appliance before starting any  installation     Read and understand all labels and diagrams attached to the  appliance     Carefully account for all components and accessories before discarding  packing materials  Store all accessories in a convenient place for later  use     CUT OUT AND INSTALLATION    Cutouts  a  Broilers may be installed in METAL COUNTERS ONLY   b  Cutout dimensions for broilers and control panels are listed on  the Installation Instructions provided with the broiler   c  Refer to the Installation Instructions for Underwriters  Laboratories Conditions of Acceptability     Mounting the broiler   a  Verify that provided sealants are applied to the under side of  the broiler top flange prior to setting the unit into the cutout   b  After installation  verify that the tab
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
Actuadores multi-voltas eléctricos SA(R) 07.1  New Template French  Cables Direct Cat5e, 2m  Hotpoint RLA80 User's Manual  ポケットプロジェクター MP180 取扱説明書  Vigo VG6061BNCL40W Use and Care Manual  USER MANUAL - WR Medical Electronics Co.  Manuale d`uso e manutenzione  取り扱い説明書PDFダウンロード  Home Automation RC-100B User's Manual    Copyright © All rights reserved. 
   Failed to retrieve file