Home

Barco MFGD 3621 Projector Accessories User Manual

1. Information Name Description Product The display type Serial No Indicates the display serial number SW Version Displays the current internal software version Display Lifetime Indicates the total time the display has been operating including the time in stand by Backlight Lifetime Indicates the total time the display has been operating excluding the time in stand by 78 Advanced display operation Advanced display operation Introduction Important The functions described in this chapter are intended for trained service staff only Improper use of these functions may cause the display to not function correctly Barco cannot be held responsible for the results or damage caused by improper use of these functions About the Advanced functions The advanced functions are extensions of the standard OSD By default a user browsing through the OSD sees only the standard functions When logged in in advanced mode the user sees the standard and advanced functions in the OSD menus To log in as advanced user 1 Enter the main menu Rotate the control wheel to select the menu item EXIT Press and hold the control wheel for a few seconds until the OSD main menu is refreshed on the screen You have now logged in as advanced user 79 Advanced display operation Advanced functions in the Luminance menu Manual Backlight This function allows to manually control the backlight luminance
2. Enable Dithering check box will be grayed out and dithering will be automatically disabled More information about Dithering is available through the on line help Disable 10 bit grayscale Use this option for standard Windows based applications that require 8 bit color support 256 colors such as Internet Explorer Excel etc Do not use this option for applications that require 10 bit pixel support 1024 simultaneous shades of gray and use extended depth graphic libraries such as WinBarco Description of 10 bit grayscale To show 1024 simultaneous shades of gray all BarcoMed H series display controllers such as the BarcoMed 5MP2FH or BarcoMed Coronis or example run in extended depth 10 bit mode by default Implications When turned on the Disable 10 bit grayscale option causes a BarcoMed Coronis display controller to run in 8 bit mode which results in increased performance since the frame buffer is set to run with 8 bit pixels While this option may be used with applications that normally require 10 bit support there will be a loss of pixel depth i e 256 shades of gray instead of 1024 simultaneous shades of gray 69 BarcoMed control panel operation Disable RGB To Static Gray Color Translation Select Disable RGB To Static Gray Color Translation if you wish to have RGB values equally weighted with 1 3 each When not selected then the International Commission on Illumination CIE Commission Int
3. Name Description Internal Temperature The temperature measured inside the dis play Sensor Temperature The internal temperature measured on the I Guard board FAN speed A value indicating the speed of the fans Minimum speed is 0 maximum speed is 1000 Sensor Y value The luminance measured by the I Guard expressed in cd m_2 nit Sensor Raw value The luminance measured by the I Guard expressed in DAC values Scan measurements Name Description DVI Input The current DVI input format DVI Link The current DVI link setting Resolution The resolution of the current input signal Clock Frequency The current clock frequency Hor Total The total number of dots horizontally of the input signal Hor Active The number of active dots horizontally of the input signal Hor Blanking The horizontal blanking of the input signal Hor Front Porch The horizontal front porch of the input signal Hor Sync The horizontal sync length of the input signal 83 Advanced display operation Name Description Hor Back Porch The horizontal back porch of the input signal Hor Frequency The horizontal frequency of the input signal Vert Total The total number of lines vertically of the input signal Vert Active The number of active lines vertically of the input signal Vert Blanking The vertical
4. When installing the display in a cupboard or another closed location heed the necessary space between the set and the sides of the cupboard Installation Place the display on a flat solid and stable surface that can bear the weight of at least 3 displays If you use an unstable cart or stand the display may fall causing serious injury to a child or adult and serious damage to the equipment More warnings in the Installation chapter Safety Instructions Operating precautions How to avoid image retention Continuous operation of the display with the same image may result in some image sticking on the LCD panel Over 10 hours operation with the same image content is not recommended To decrease the risk of image sticking image retention e Switch on DPMS on display and PC Activate a good screen saver This apparatus conforms to CE LVD 73 23 EEC IEC 60950 1 UL 60950 1 CAN CSA 22 2 No 60950 1 c UL EN 60950 1 DEMKO CCC GB4943 1995 National Scandinavian Deviations for Cl 1 7 2 Finland Laite on liitettava suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet ma tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag Explanation of symbols Explanation of symbols Symbols on the display and or power supply On the display or power supply you may find the following symbols pike or 2 ASSIF SNS Oy or x A Indicates the dis
5. gt Control Panel gt Display or b Open the Display Properties Control Panel by right clicking in an empty area on the desktop then select Properties Click on the Settings tab Select the rectangle that represents the Barco Coronis display whose settings you wish to change y Note If you are using the VGA capabilities of your BARCOMED Coronis display controller the resolution for the first display may be set to a VGA resolution of 640 x 480 pixels with 16 colors and a default refresh rate If your BarcoMed Coronis controller is not running VGA the display may not be enabled yet To enable the display check the Extend my Windows desktop onto this monitor checkbox but do NOT click the Apply button at this time If you installed your Barco Coronis Display System drivers in SingleView mode default for Windows 2000 there will be one rectangle for the virtual display representing the two heads controlled by each BarcoMed Coronis display controller If you installed your Barco Coronis Display System drivers in DualView mode default for Windows XP there will be a rectangle representing each head controlled by each BarcoMed Coronis display controller This will be true even if you have only one display connected to your BarcoMed Coronis controller Both displays of a display controller cannot be enabled at the same time unless their display properties match If necessary detach the second displ
6. 20 standard system colors are converted from RGB to gray values and are added to the 236 static gray values Applications are denied the ability to dynamically change or allocate palette entries Static Gray Palette with NO system colors This option sets the palette to be a static linear ramp of 256 shades of gray Applications are denied the ability to dynamically change or allocate palette entries Drawing Modes In the Drawing Mode section you can choose from the following Drawing Modes If any of the options in this section are grayed out then they are not available for the model controller with which you are working Enable DirectDraw This option allows the user to enable or disable DirectDraw DirectDraw is a software interface that provides direct access to display devices 68 BarcoMed control panel operation while maintaining compatibility with the Windows graphics device interface GDI DirectDraw is enabled by default More information about DirectDraw is available through the on line help Enable Dithering This option allows the user to enable or disable dithering Dithering is a technique for increasing the perceived range of colors in an image at the cost of spatial resolution N Note This option is only available when the User Modifiable Palette mode is selected If either the Static Gray Palette including Standard System Colors mode or the Static Gray Palette with NO System colors mode is selected the
7. Pitch 0 27 mm H x 0 27 mm V Native color resolu tion 8 bits sub pixel Luminance 500 cd m calibrated Contrast ratio 700 1 typical in dark environment Response time 17 5 ms typical 25 C after 30 min warm up Controls Push turn control wheel for stand by switching and OSD controls Input connectors DVI dual channel Signal systems DVI Digital Sync on DVI Complying to DVI Rev 1 0 spec ifications Input signals Possible resolutions 640 x 480 60 75 85 100 Hz 1600 x 1200 59 60 Hz 1200 x 1600 59 Hz 107 Technical specifications Item Specification Power source Input for 12 VDC power supply unit 90 264 VAC Input for display 12 VDC The supplied 12VDC power supply must be used Power consumption 64 watts max at 90 VAC maximum back light USB load Dimensions W x H x D In perpendicular vertical position highest position tilt 0 swivel 0 385 x 585 x 250 mm Net weight 13 9 kg Operating Tempera ture 0 C to 40 C 15 C to 35 C within specs Storage Temperature 20 C to 60 C Humidity 8 80 non condensing for operation 5 95 non condensing for storage Altitude 7500 m storage 3000 m operation MFGD 3621 Item Specification 108 Picture panel 21 3 inch diagonal viewable screen TFT thin film transistor active
8. Rotate the control wheel 1 step counterclockwise The on screen display appears Note Steps 2 to 4 must be performed in maximum 3 seconds Rotate the control wheel to select Settings Press the control wheel to enter the Settings menu SETTINGS DPMS On Power LED On User Controls Off EXIT Figure 27 Settings menu Rotate the control wheel to select User Controls Press the control wheel to switch from Off to On Exit the menus Display operation Complete OSD overview Main menu Name Description Luminance Adjust the target luminance to which the dis play will be stabilized Settings Change settings for DPMS Power LED and User Controls Information Read information about the display Luminance Name Description Luminance Target Manually adjust the luminance The luminance is indicated in cd m nit Luminance Target adjusts the overall luminance light output of the display It does not affect the grayscales of the image on the screen 77 Display operation Settings Name Description DPMS Switch on off the automatic power saving sys tem DPMS Power LED Switch the power LED on off Note The LED s orange DPMS state is not influenced by this set ting So when the display goes into power sav ing mode the LED will turn orange even if it was switched off by this setting User Controls Disable the control wheel functions
9. When you control the Manual Backlight function the Luminance target function and I Guard control are disabled Important Disabling the I Guard results in an uncalibrated and not stabilized backlight After switching the power off and on again the Luminance target and I Guard control are activated again This is also the case when you control the Luminance function again Advanced functions in the Settings menu Panel position Click to select the desired option Auto Select if the display will be used in both portrait and landscape orientation Portrait Select if the display is always used in portrait orientation Landscape Select if the display is always used in landscape orientation Auto Rotation When switched on the image will be rotated automatically when switching between portrait or landscape orientation DVI Input Click to switch between normal DVI signal Dual10 DVI signal or automatic detection of the DVI format 80 Advanced display operation DVI Link Click to switch between single link Single and automatic detection of single or dual link Auto Stabilizer Click to switch the backlight stabilizer on off Patch Click to hide display the Guard patch When you hide the patch the l Guard will not function properly anymore Important Disabling the I Guard results in an uncalibrated and not stabilized backlight Burn In Mode When switched on the display will generate a
10. divided into four sections Palette Mode Drawing Modes Monitor Configuration Graphics Board Palette Mode In the Palette Mode section you can choose one of the four following Palette Modes If you are using a color display in conjunction with your Barco grayscale display s prior to selecting a palette mode please make certain that you have configured your Windows desktop correctly See the section Setting the resolution of your Coronis display on page 102 Color to Gray Compatibility Use this palette option for applications such as Java which require True Color support Such applications may not work correctly when using one of Barco s three Standard 8 bit 256 color palette modes All 67 BarcoMed control panel operation applications that are designed to work correctly with 8 bit 256 color modes should continue to work normally N Note Ditherng is not used while in this mode Also direct access to the hardware through DirectDraw is not allowed in this mode User Modifiable Color Palette This option allows applications to modify the palette contents dynamically This mode reserves the first 10 and last 10 entries in the palette for the Windows operating system but applications can manipulate the middle 236 entries This is the standard palette mode as configured by Windows Static Gray Palette including standard system colors This option sets the palette to be a static linear set of 236 gray values The
11. matrix gray scale liquid crystal display Resolution Native 2048 x 1536 Display area H x V 433 2 x 324 9 mm Viewing angle 10 1 contrast Vertical 170 Horizontal 170 Pixel Pitch 0 2115 mm H x 0 2115 mm V Technical specifications Item Specification Native color resolu tion 8 bits sub pixel Luminance 500 cd m calibrated Contrast ratio 700 1 typical in dark environment Response time 17 5 ms typical 25 C after 30 min warm up Controls Push turn control wheel for stand by switching and OSD controls Input connectors DVI dual channel Signal systems DVI Digital Sync on DVI Complying to DVI Rev 1 0 spec ifications Input signals Possible resolutions 640 x 480 60 75 85 100 Hz 2048 x 1536 60 Hz Power source Input for 12 VDC power supply unit 90 264 VAC Input for display 12 VDC The supplied 12VDC power supply must be used Power consumption 66 watts max at 90 VAC maximum back light USB load Dimensions W x H x D In perpendicular vertical position highest position tilt 0 swivel 0 385 x 585 x 250 mm Net weight 14 kg Operating Tempera ture 0 C to 40 C 15 C to 35 C within specs Storage Temperature 20 C to 60 C Humidity 8 80 non condensing for operation 5 95 non condensing for
12. may ask to return the faulty equipment or faulty subassemblies to the BarcoView Customer Support Center or an authorized service center for repair activities The Customer shall ask for a RMA or RAN number to a BarcoView Customer Support Center or an authorized service center 1 3 The Customer shall return freight prepaid the defective equipment or subassemblies for repair to the BarcoView Customer Support Center or an authorized service center 1 4 Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment The warranty period for the replacement parts will expire at the same moment as the original warranty period of the equipment All parts replaced hereunder and returned to BarcoView or an authorized service center shall become the property of BarcoView or the authorized service center 1 5 The repaired equipment shall be returned to the Customer by regular freight at BarcoView s charge 115 Warranty Statement ARTICLE 2 ITEMS EXCLUDED FROM WARRANTY The warranty described herein shall not include the following 2 1 Any hardware or software item procured from a source other than BarcoView or their official agent or distributor and integrated by Customer or a third party into BarcoView supplied equipment 2 2 Any host configuration not explicitly supported by BarcoView 2 3 All software installed on the system whether they are acquired from BarcoView or third party An exce
13. of MediCal QAWeb MediCal Pro or NioWatch BarcoMed SelfExam and the Barco on line documentation 14 When the Setup complete message appears select Reboot System Now and click Finish Automated display configuration Once the drivers software and documentation have been installed and your system has been rebooted the Barco Monitor Plug and Play Software should automatically detect your Barco displays and attach them to the desktop with the correct resolution If the Barco Monitor Plug and Play Software fails to detect your Barco displays or fails to attach them to the desktop correctly please refer to the section Setting the resolution of your Coronis display on page 102 in the Troubleshooting section of this manual Reinstalling drivers You can install new drivers or reinstall existing drivers at any time by using the Barco Set up wizard on your Barco system CD ROM see Installing the BarcoMeo display controller drivers and software on page 53 of this manual Uninstalling the drivers and software To un install the Barco MEDICAL IMAGING DISPLAY SYSTEM drivers software or documentation please use the Windows Add Remove Programs utility This can be found in the Windows Control Panel N Note If you installed your BARCO MEDICAL IMAGING DISPLAY SYSTEM drivers with DualView enabled the wizard may warn you that DualView must be disabled before the drivers can be un installed This is normal please follow the prompts from the
14. the VGA capabilities of the display controller 31 BARCOMED Coronis display controller installation Figure 4 VGA Jumper Enlarged View Using the VGA capabilities of the BarcoMed Coronis Prior to installing the BarcoMed Coronis decide if you are going to use its on board VGA capabilities If you are check the setting of the Jumper at J 1 on the display controller see figure 4 VGA Jumper Enlarged View By default VGA should be enabled on the top two pins NOTE To use multiple BarcoMed Coronis display controllers ina single host with VGA enabled you need to enable VGA on only ONE of the BarcoMed Coronis display controllers and disable VGA on ALL other BarcoMed display controllers Examples of PCI slots Although the BArcoMED Coronis controller is a 64 bit board it may be installed in either a 64 bit or 32 bit PCI slot However installing it in a 32 bit PCI slot will result in a decrease in performance Figure 5 illustrates the types of slots so that you can correctly identify which one to use for the BarcoMed Coronis 32 BARCOMED CORONIS display controller installation OK TO USE DO NOT USE CTT Coo Non conforming 32 bit PCI Slot OK TO USE DO NOT USE RAID Controller Slot Figure 5 PCI and RAID Controller Slots Install the BarcoMed Coronis controller in your computer following these steps 7 Turn off the power to you
15. white image when the video cable is unplugged Advanced functions in the Information menu Service The Service information menu contains the following items Name Description Display Name The display type Display Ser No Indicates the display serial number Display Stock No Indicates the display order number Panel Ser No Indicates the flat panel serial number Panel Prod Date Indicates the flat panel production date 81 Advanced display operation Firmware The Firmware information menu contains the following items Name Description Boot Code Version The version of the internal boot code Run Code Version The version of the internal run code CPLD Code Version The version of the internal CPLD code Transpose Version The version of the internal Transpose circuit code Runtimes Runtimes is a submenu from General Information containing the following items Name Description Display Lifetime Indicates the total time the display has been operating including the time in stand by Backlight Lifetime Indicates the total time the display has been operating excluding the time in stand by Backlight Runtime Indicates the time the backlight has been on since the last time it was switched off e g in stand by This counter stops after 1092 min utes 82 Advanced display operation Measurements
16. wizard 55 Display controller software installation Command line Silent Install of Drivers and Software Specifying the silent install option causes most of the GUI associated with the installer to disappear A background progress window will still be visible but no user input will be required The silent install behavior is dictated by the SETUPINI file Each application is allowed to have separate command line parameters for normal and silent installs To install the drivers and software silently please follow the steps below 1 56 Insert the BARCO MEDICAL IMAGING DISPLAY SYSTEM CD ROM into your CD DVD drive When the Barco Product Installation Wizard starts click Cancel Click the Start button in the task bar Click Run Click Browse and a browse to the root directory of the BARCO MEDICAL IMAGING DISPLAY SYSTEM CD ROM b Click on the file Setup exe and click Open or a Browse to the root directory of the location where you saved the contents of your BARCO MEDICAL IMAGING DISPLAY System CD ROM b Click on the file Setup exe and click Open In the Open address window place your cursor at the end of the line of text that appears and add the following text after Setup exe a space and silent Click OK Example where D is the name of your CD DVD drive D Setup exe silent See figure 21 for an example of how the command line window should look when using the silent install from the Barco MEDI
17. CAL IMAGING DISPLAY SYSTEM CD ROM Display controller software installation Figure 21 57 Display controller software installation This page intentionally left blank 58 r optimal display ce throughout the product lifetime Avoiding image retention Avoiding image retention Image retention image sticking ghost image is the phenomenon where an image or a part of it seems to be burnt in the LCD panel When you display e g a uniform light gray image you distinguish the ghost image in the background This phenomenon occurs on all types of LCD panels when a static image remains on the screen for a long time unfortunately the exact period is not predictable Also parts of the image that do not change often e g toolbars buttons borders are susceptible to image retention Image retention may be undone in some cases but it may also damage the LCD panel permanently So it is better to take precautions during product installation to avoid it Here are some countermeasures you can take Power off power save mode screen saver Very important is to use screen savers and power saving modes as much as possible If you do not need the display for a few hours switch it off If you only need to look at it when you actually do something on the screen use a screen saver The amount of relaxation time should be considerable the more you do it the better Flashing the screen for a few seco
18. CI Express Controllers cccccccceeseeesesesesesesesees 35 Display installation cccssscsssscsssssesssccsssessssseesessacssseeseeseeseeseees 37 Installation PreCAUtiONS cccccscesesesssesesesesesesesesesesesesesesesesesesesees 39 After unpacking the diSPlaY s sesessessessessensrnsrssrnsrrsrnsrnnnnnnnnnnna 40 Power CONNECU ON sess cvtsts tecsevssiescesoventt tutes RA RR 44 Video Connection ossoseesresresresresresrrsrnsrenrensrn sr sr ren sen sen sen ren rensar ren nen enn rena 45 USB COTIM EC T an aiaa E E TA KANSAS AEA 46 CDG TOUTING isien 47 Attaching the display to an arm Stand eceecseeseseseseeeees 49 Display controller software installation ssssssesesrsossesrsrsrsrsnn 51 Installing the BARcoMeD display controller drivers and software 53 Settings for optimal display performance throughout the product life LL E ras KRANEN KARNA ARA SANNA et ele E A E E A A HN ER GK 59 Avoiding image retention sm se sessessensrnsensrnsrnsensensrnsrnsrnn ennen ennen nanna 60 Display controller tools cscssccsccsscssssssscssssscessscssessseecsessssensenes 63 BarcoMed control panel Operation essessersersensensensrnsrnsnnsnn nn nn 65 ACCESSING the Barco tab eceescsesesescsesescsesescsescsescseeteeeees 65 Table of Contents Advanced Properties sm mmmmmssessessensensrnsrnsrrsrnsrnsensrrsrns ennen ennen enn nn na 67 Device detailS i Acctcs G tevin dna cinta EEA 70 Di
19. Coronis 21 inch Installation amp User Manual Supported displays MFGD 2621 MFGD 3621 This page intentionally left blank Copyright notice This document is copyrighted All rights are reserved Nor this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Barco 2007 Barco N V All rights reserved This page intentionally left blank Table of Contents Table of Contents Preface vsnccetscdestsusdadbssscceasssencsadiicssesccesbedacceasscanssdascesesesecevucuaaccnatesacaases 7 Safety INStIUCTIONS on a E RARE 11 Explanation of symbols oissmnsessessessersrssesressessrnsrnrensrnsrnsrnsrn sens en sen srn nen nen 14 INTE O CU CI OT sinnena cus pdb Ea aE Ee Ea iE 17 OVENI W ar era NN OST A ATE O RR ues 19 Single display or complete SYSteM s sesensensensensensrnsnnnnnnnnn 19 BARCOMED CORONIS display controller overview sesessseesiosnnnsnn 20 Barco displays Overview c cccsccceseesseeseteseseseseseseseseseseseseseeees 22 Package contents sisicnu aca skida ad eras ed eG ecole 24 Parts controls and CONNECHOMS s sssesrsrsrsrsrrsrsrsrsrrererersrsrsesese rer nna 25 Display controller installation u sesessssesesrsrsrsrrsrsrsrsrrrnrnrnnrsnrnrrsrsr nn 29 BARCOMED Coronis display controller installation 31 BarcoMed P
20. Ei EET ina an goo F Ror PCI Express x1 Slot AN se Figure 7 Examples of PCI Express Slots 35 BARCOMED Coronis display controller installation This page intentionally left blank 36 tallation 37 Display installation This page intentionally left blank 38 Installation precautions Installation precautions Precautions Keep your original packaging It is designed for this display and is the ideal protection during transport e Avoid reflections in the flat panel to reduce eye strain e Place the display on a strong and stable table or desk Keep the display away from heat sources and provide enough ventilation around the display Do not use the display in direct sunlight Do not scratch or apply pressure to the LCD panel This may damage the panel permanently 39 After unpacking the display After unpacking the display Important In the factory the height positioning system in the display foot is blocked with a red clip to prevent damage during transportation Before installing the display you must remove this clip Clip Figure 8 To remove the clip 1 Position the display with its rear side facing you 2 Pull the red clip out of the fixation holes in the foot 3 Keep the clip in case the display needs to be shipped later 40 After unpacking the display Adjust the panel orientation You can change the orientation of the panel at an
21. ONNEL Type of protection electrical Class equipment Degree of safety flammable anesthetic mixture Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Power connection Power requirements The display must be powered using the 12 VDC power supply that is supplied with the display The 12 VDC power supply must be powered by the AC mains voltage Power cords Power cord with CEE 7 plug The colors of the mains lead are colored in accordance with the following 0 Safety Instructions code Green and yellow Earth safety earth Blue Neutral Brown Line Power cord with ANSI 73 11 plug The wires of the power cord are colored in accordance with the amp following code Green yellow ground White neutral Black line live Do not overload wall outlets and extension cords as this may result in fire or electric shock Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacles Water and moisture Never expose the display to rain or moisture Never use the display near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement Ventilation Do not cover or block the ventilation openings in the cover of the set
22. To connect the USB cable Figure 16 1 Connect a PC USB downstream connector to the display s USB upstream connector by means of a USB cable 2 Connect any USB device to one of the display s USB downstream connectors 46 Cable routing Cable routing Routing the signal cables Bind the cables in the connector compartment together with the cable tie inside the connector compartment Put the connector compartment cover back on the display Pay attention that the signal cables are positioned under the bulge in the cover e Push the cables into the clips on the rear of the tilt amp swivel foot Bind the cables together above and under the foot by means of the 2 velcro strips attached to the inside of the foot cover packed inside the accessory box At last put the foot cover back in place To put the foot cover in place lt 2 aS Figure 17 1 The foot cover is packaged separately in the accessory box Unpack the foot cover 2 Push the upper side of the cover onto the foot so that the hooks inside the cover are positioned right under the bulges at the rear of the foot 47 Cable routing 3 Slide the cover upward while moving the lower side of the cover towards the foot 4 Press the cover to the foot so that it makes a clicking sound 48 Attaching the display to an arm stand Attaching the display to an arm stand The panel standard attache
23. adjustment value e g the luminance value rotate the control wheel to select the adjustment and press the wheel shortly The adjustment name appears as well as the current adjustment value Rotate the wheel to change the value When done press the wheel shortly to confirm the change and return to the menu To select a value from a predefined list e g in Settings rotate the control wheel to select the setting and press the control wheel until the desired value appears Locking and unlocking user controls The User Controls function allows to disable or enable the control wheel functions When user controls are disabled you cannot e display and use the on screen display e switch the display in stand by mode To disable user controls 1 Rotate the control wheel to display the on screen display The Main Menu appears Rotate the control wheel to select Settings Press the control wheel to enter the Settings menu SETTINGS DPMS On Power LED On User Controls On EXIT Figure 26 Settings menu 75 Display operation 4 5 6 Rotate the control wheel to select User Controls Press the control wheel to switch from On to Off Exit the menus To enable user controls N R WN M 10 76 Make sure the on screen display is not on the screen Do not use the control wheel for at least 3 seconds Rotate the control wheel 1 step clockwise Press the control wheel 2 times
24. ay of the BarcoMed Coronis display controller you are General tips working with by right clicking on the rectangle that represents it deselect Attached and click the Apply button Note Since Windows will not let you detach the primary display connected to a particular controller you may need to temporarily make another display the primary display 4 For the display which is still attached click Click on the Advanced Button 5 Select the Adapter tab and then click on the List All Modes button Select the resolution and refresh rate that your Coronis display supports from the dialog box and click OK gt Note In the Adapter box the Adapter string shows if this display is the First View or the Second View attached to the display controller Please make a note of this so that you can arrange the displays in the correct order later if necessary 6 Click OK on the bottom of the Adapter Control Panel If the OK button on the bottom of the Adapter Control Panel is not visible press the TAB key once and then press CTRL Enter to select OK 7 Click OK in the Windows will now apply your new desktop settings dialog box Your Coronis display should now synchronize and display the Windows desktop 8 Click Yes when asked Your desktop has been reconfigured Do you want to keep these settings To set the resolution of the second display at
25. blanking of the input signal Vert Front Porch The vertical front porch of the input signal Vert Sync The vertical sync length of the input signal Vert Back Porch The vertical back porch of the input signal Vert Frequency The vertical frequency of the input signal Advanced functions in the Adjustments menu In Advanced mode the main menu contains an additional menu Adjustments This menu contains the submenu Miscellaneous Miscellaneous Adjustments The Miscellaneous adjustments are intended for internal purposes only Adjusting them will have no result The Miscellaneous menu contains the following items Name Description RS232 Address Rotate the control wheel to change the inter nal display address 84 0 software 85 MediCal Pro software This page intentionally left blank 86 MediCal Pro installation and operation MediCal Pro installation and operation MediCal Pro software installation Install MediCal Pro on the PC Follow the instructions from the MediCal Pro User Guide Important Do not forget you have to have Administrator privileges to install or uninstall MediCal Pro Using MediCal Pro You can now use MediCal Pro to configure the complete configuration and set up the Q A tasks Proceed as follows 1 Start MediCal Pro If appropriate you can connect to MediCal Administrator 2 Setup the configuration in MediCal Pro by using the Configuration Set
26. calibrate their viewing stations or adjust the panel s curve to DICOM standards without administrator intervention Power saving The display is equipped with a power saving system When left idle for a certain time the computer connected to the display will power down the display The power saving system can be switched on or off using the on screen menus The power saving system works with the standard Windows power saving and with the DPMS function on the BarcoMed display controller 22 BARCOMED Coronis display controller overview Tilt amp swivel base The versatile tilt amp swivel foot allows to use the display for viewing portrait or landscape image resolutions The user can easily change the panel height and viewing angle allowing to use the display in the optimal viewing conditions 23 Package contents Package contents Coronis System package Each Coronis system contains one or more display boxes see below and a system accessory box containing the following items Display controller s CD ROM with driver and documentation MediCal Pro software MediCal Pro user manual Display box Each display box includes one display and a display accessory box containing the following items Plastic cover of the tilt amp swivel foot e Power supply Digital video DVI cable 25 pins Analog video VGA cable 15 pins USB cable e Two velcro strips to bind the cables European power co
27. ching on DPMS on display and PC and activating a good screen saver may decrease the risk of image sticking image retention Stand by switching When the display is on and no on screen display is visible push and hold the control wheel at the front for a few seconds to switch the display in stand by The LED turns orange Push and hold Figure 23 When the display is in stand by press the control wheel to switch it back on 73 Display operation About the On Screen Display OSD About the on screen display The on screen display OSD has a hierarchical tree structure with several levels The top level is the Main Menu MFGD X621 MAIN MENU Luminance Settings Information EXIT Figure 24 Main menu in standard mode How to navigate through the OSD 1 When the OSD is not on the screen rotate the control wheel to display the OSD The main menu appears 2 To enter into a menu First rotate the control wheel to select the desired menu Next press the wheel shortly MFGD X621 MAIN MENU Luminance Settings SETTINGS Information DPMS On EXIT Power LED On User controls On EXIT 1 Rotate the control wheel 2 Press the control wheel Figure 25 OSD menu navigation 74 Display operation 3 To exit from a menu rotate the control wheel to select EXIT and press the control wheel shortly If you exit from the Main Menu you exit the OSD To change an
28. coarse tools Lye is a strong caustic alkaline solution of potassium salts 91 Front glass Front glass Proceed as follows e Clean the glass using a soft cotton cloth lightly moistened with plain water e Wipe dry with a dry cloth 92 Cabinet Cabinet Proceed as follows e Clean the cabinet using a soft cotton cloth lightly moistened with a recognized cleaning product for medical equipment e Repeat with water only e Wipe dry with a dry cloth The cabinet has been tested for resistance to the following products Cidex Betadine Alcohol Isopropyl and Ethyl Ammonia based cleaners Windex and Aquasonic Gel 93 LCD panel LCD panel It may be possible that dust particles have entered the display and are stuck behind the front glass IN We recommend to let this cleaning procedure be done in a BARCO service center The product warranty expires when the user removes the glass panel or otherwise opens the display However when really necessary you can perform the cleaning on site if you can work in dust free conditions This is to avoid more dust entering the display when opening it To remove the glass panel Figure 28 1 Switch off the display Tilt the panel Unscrew the 4 sunken screws at the rear fixing the glass panel and bezel 28 4 Carefully take the glass panel a few centimeter from the display It is still connected to the rest of the display by means of the LED connec
29. d to the tilt amp swivel foot is compatible with the VESA 100 mm standard So it can be used with an arm stand according to the VESA 100 mm standard Therefore the tilt amp swivel foot must be removed from the panel Important Use an arm that is approved by VESA according to the VESA 100 mm standard Use an arm that can support a weight of at least 13 kg 28 66 Ibs To attach the display to an arm stand 1 Put the display face down on a clean and soft surface Be careful not to damage the panel screen Remove the tilt amp swivel foot cover Remove the small screw A fixing the small plastic cover on top of the foot Next remove the small cover itself Figure 18 Display with tilt amp swivel foot cover removed 4 Unscrew the 2 screws fixing the round plastic cover B 5 Lift up the round plastic cover 49 Attaching the display to an arm stand 6 Remove the four screws fixing the foot while supporting the foot 7 Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm 4 screws M4 x 8mm Figure 19 50 ntroller software n 51 Display controller software installation This page intentionally left blank 52 UP Display controller software installation Installing the BarcoMen display controller drivers and software Note The installation dialog will display in English if your operating system s language is not support
30. device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Canadian notice This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la Classe A est conforme a la norme NMB 003 du Canada Preface Disposal Information The lamps inside the display contain mercury Do not throw the display in the trash Dispose of it as required by local ordinances or regulations Safety Instructions Safety Instructions General Recommendations Read the safety and operating instructions before operating the display Retain safety and operating instructions for future reference Adhere to all warnings on the display and in the operating instructions manual Follow all instructions for operation and use Electrical shock RISK OF ELECTRIC SHOCK 4 DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERS
31. downstream port USB downstream port When the display is connected to the PC USB bus you can connect USB devices such as keyboard mouse digital camera to this connector DC power input Parts controls and connectors Connect the external power supply delivered with the display to this connector 9 Tilt amp swivel foot clip The display is shipped with this clip in the foot to protect the tilt amp swivel mechanism during transport After unpacking you should remove this clip Do not throw the clip away Should the display have to be packed and shipped later the clip must be applied to the foot again 27 Parts controls and connectors This page intentionally left blank 28 ntroller installation 29 Display controller installation This page intentionally left blank 30 BARCOMED CORONIS display controller installation BARCOMED Coronis display controller installation A Caution Wear a grounded protective ESD strap during installation or handling of the display controller Electrostatic charges can damage the display controller Prior to installing your BARCOMED Coronis display controller s in your PC please take a few minutes to familiarize yourself with both the display controller and the PCI slots in your computer Figure 3 The BarcoMed Coronis PCI display controller Jumper location There is one user changeable jumper on the BarcoMed Coronis It is used to enable or disable
32. e Barco MEDICAL IMAGING DISPLAY SYSTEM CD ROM and click on the file Setup exe and click Open d Click OK or a Browse to the root directory of the BARCO MEDICAL IMAGING DispLay SYSTEM CD ROM and double click on the file Setup exe Click Next on the Welcome page Click Next on the Components to be installed page Follow the wizard s on screen instructions to complete the installation Note When the page shown in figure 20 appears you may either click Next to accept the default settings or if you know the settings required for your viewing application you may select them now and then click Next You may change these settings later by using the Barco pages of the Windows Display Control Panel B AR G O palette mode C color to gray compatibility user modifiable palette static gray palette including standard system colors Visibly yours static gray palette with NO system colors drawing modes enable direct draw IV Disable 10 bit grayscale I Disable RGB To Static Gray Color Translation IV Disable Menu Shadow Effect IV Disable Menu Fade Effect lt Back Next gt Cancel Figure 20 Please refer to your application manuals for information on the correct Palette and Drawing modes to select 54 Display controller software installation 13 When the driver setup is complete click the Finish button The Barco Product Installation Wizard will now guide you through the installation
33. e problem by switching video cables or power supplies In that way you can find out if the problem resides in the display or not 99 General tips Problems and solutions Problem description Possible tests or solutions Screen remains black Please check the installation procedure in this manual If the LED at the front is orange the display is in stand by Check in the Windows Display Properties if the display controller video heads are attached If not there will be no image on the screen The external power supply may be defective Image exhibits noise or interference The video cable may be of poor quality DVI video cable may not be firmly connected to the PC or to the display Image contains missing pixels A number of missing pixels may be normal inherent in LCD technology Image contains not enough grayscales You may have installed the driver software with an inappropriate selection of Palette Settings Static Gray with or without System Colors Install the driver software again using a different setting for Palette Settings The PC does not start up Check the CMOS settings in the PC BIOS The display controller may not be firmly seated in the PCI AGP connector 100 General tips Problem description Possible tests or solutions No image during PC start up Check the VGA jumper settings on the display controller Check the CMOS set
34. ed This process applies to the following versions of Windows Windows 2000 Professional Windows XP Professional Windows Professional x64 Edition Windows Server 2003 and e Windows Server 2003 x64 Edition You will need to install the BARCO MEDICAL IMAGING DISPLAY SYSTEM drivers and software in the following cases After you have installed the display controller s for your BARCO MEDICAL IMAGING DISPLAY SYSTEM in your system for the first time After you have reinstalled or upgraded your operating system 8 Start your system When the Found New Hardware Wizard comes up click Cancel When the System Settings Change window asks you to restart your computer click No Note Both displays connected to a single display controller must have the same physical orientation and resolution in order to be attached to the Windows desktop 9 Run the Barco Product Installation Wizard The Barco Product Installation Wizard should start automatically when you insert the Barco System CD ROM into your CD drive after the operating system has started If your CD drive s auto run is not enabled or the Barco Product Installation Wizard does not start automatically you can run the Barco Product Installation Wizard manually by following these steps a Click the Start button in the task bar b Click Run 53 Display controller software installation 10 11 12 c Click Browse and browse to the root directory of th
35. edetessscosestbasenssitecasbedesvactaedavsetelises 97 General tipsi Beerin a eds lies aaesals 99 Technical Information cscecsesecseseceececescecsececcecsceececeececeeescees 105 Technical Specifications s e sessesseeseesresensrnsrnsensrnsen sens enn ennen enn ennen 107 Connector PIN aSSIGNMENTSosooeessssrsrsrsrsrrererersrsrsrsrsrrenensnsrsrnenener enn rna 111 GIOSS ANY 22s en oe eA eR ita nt oes 112 Walranty Statement snn reiese nera aasien iia 113 Preface This page intentionally left blank Preface Notice Although every attempt has been made to achieve technical accuracy in this document we assume no responsibility for errors that may be found Our goal is to provide you with the most accurate and usable documentation possible if you discover errors please let us know BarcoView software products are the property of BarcoView They are distributed under copyright by Barco N V or BarcoView LLC for use only under the specific terms of a software license agreement between Barco N V or BarcoView LLC and the licensee No other use duplication or disclosure of a BarcoView software product in any form is authorized The specifications of BarcoView products are subject to change without notice Trademarks All trademarks and registered trademarks are property of their respective owners FCC notice display This equipment has been tested and found to comply with the limits of a Class A digital
36. ernationale de Eclairage model will be adapted which weights the colors as 59 Green 30 Red 11 Blue Monitor Configuration If the options in this section are grayed out then they are not available for the model controller with which you are working Graphics Board There is one option in this section the Update Firmware button Clicking this button will launch the BarcoMed Hardware Configuration utility This program allows the user to flash update the firmware stored in the ROM of the currently selected BarcoMed display controller The BarcoMed Hardware Configuration utility is implemented in a Wizard format which guides the user through the flash update procedure The user will be prompted to select a firmware update file to use for the update process This file will be provided by Barco Medical Imaging if and when a firmware update is required Device details The Device Details page provides detailed information about the display controller connected to the active display This information is useful in debugging issues that may occur when using your Barco Medical Imaging Display System 70 eration 7 Display operation This page intentionally left blank 72 Display operation Display operation Operating precautions Continuous operation of the display with the same image may result in some image sticking on the LCD panel Over 10 hours operation with the same image content is not recommended Swit
37. evice Type Seny hunter Ourver Versor Firsmsase Vertion Resokstinn Coly Depth Advancad Deplap Informator Display Name Soral Number Backkor teteve Barco Sytem Flepot QA wet Baman ATI Ca Figure 22 Barco Tab Barco System Report The Barco System Report also known as BarcoMed SelfExam is a wizard based tool which collects data about the components that are installed in your system This information is used by the Barco MID Support team when trying to resolve customer issues MediCal QAWeb MediCal Pro NioWatch Clicking on the MediCal QAWeb MediCal NioWatch Pro button will launch the softcopy QA application that is installed on your system Please refer to the MediCal QAWeb MediCal Pro or NioWatch manual for information about this application 66 BarcoMed control panel operation Advanced Properties To access the advanced properties configuration pages for your Barco display controller s click on the Advanced button in the Graphics Device Information section BarcoMed advanced configuration There are two pages accessible from the advanced configuration button They are Barco Drawing Modes Device Details These two pages replace the following three pages found in earlier versions of the BarcoMed display controller drivers the BarcoMed Driver Tab the BarcoMed Hardware Tab and e the BarcoMed Display Tab Barco Drawing Modes The Barco Drawing Modes page of the Advanced Properties page is
38. host The physical order of the displays may vary when you are running multiple BarcoMed Coronis display controllers This is due to the PC s PCI bus control in the system BIOS and not the BarcoMed display controller It may become necessary depending on how your PC s BIOS configures the PCI bus to switch your DVI display connections to achieve a linear desktop configuration Figure 6 The Video Outputs 34 BARCOMED CORONIS display controller installation BarcoMed PCI Express Controllers During the first quarter of 2006 Barco Medical Imaging Systems added PCI Express PCle versions of its Coronis and Coronis 5MP display controllers to its grayscale Medical Imaging Display Systems product line The PCle versions of these boards will have the same features as the currently shipping PCI version All three PCle boards will feature a x8 logical bus on a x8 physical connector They have been designed to function in PCI Express x8 or x16 slots Optimum performance will always be obtained by installing them in a PCle x8 slot Depending on your PC manufacturer s implementation of the logic for the PCle x16 slot optimum performance may also be obtained by installing the Barco PCle boards in the PCle x16 slot Connecting your Barco displays to your BarcoMed PCle board is identical to connecting them to a BarcoMed PCI board please refer to your system manual for details PCI Express x16 Slot Ax GF AE m TT LT UL PEELE
39. ndows Display Control Panel Accessing the Barco tab Note You must have logged on to Windows using an account with administrator privileges in order to use the Barco portions of the Windows Display Control Panel to change any display settings 1 Open the Windows Display Control Panel by one of the two methods below a Start gt Settings gt Control Panel gt Display or b Open the Display Properties Control Panel by right clicking in an empty area on the desktop then select Properties Click on the Settings tab Select the rectangle that represents the Barco display whose settings you wish to change Click on the Advanced button 5 Select the Barco tab from the Properties screen Using the Barco tab The Barco tab is divided into three sections The first section provides information about the graphics controller and allows access to the graphics controller advanced configuration pages The second section provides information about the display The bottom section allows access to two Barco tools Barco System Report and Barco s softcopy QA solution MediCal QAWeb MediCal Pro or Niowatch depending on which solution is installed on your system Also there is a active link to the Barco Medical Imaging web site 65 BarcoMed control panel operation J Genial Adapter Monitor Troubleshoot Coke Management Baco Gesohics Device Infomation ES D
40. nds with a screen saver is not sufficient Image retention is a slow process to build up but it also disappears slowly Re Layout In most applications a display is used to show a layout of several components with borders Whereas the content in these windows can change continuously the borders are static images and may cause boundary image retention The layout of the windows size number of windows etc should be changed as much as possible 60 Avoiding image retention To activate appropriate screen saving proceed as follows 1 In the display OSD menus open the Settings menu and switch DPMS on For more information please consult the display operation chapter In Windows open the Display control panel Open the Screen Saver tab Select a screen saver from the Screen saver drop down box Set the Wait time to 10 minutes Click the button Power The Power Options Properties dialog opens In the Turn off monitor drop down box select After 20 mins Click Apply Close the control panel 61 Avoiding image retention This page intentionally left blank 62 ntroller tools 63 Display controller tools This page intentionally left blank 64 BarcoMed control panel operation BarcoMed control panel operation This chapter describes how to configure the displays in your Barco Medical Imaging Display System using the tools available through the Advanced button on the Settings tab of the Wi
41. play is approved according to the CE regulations Indicates the display is approved according to the UL regulations Indicates the display is approved according to the c UL regulations Indicates the display is approved according to the DEMKO regulations Indicates the display is approved according to the CCC regulations Indicates the USB connectors on the display Indicates this apparatus must not be thrown in the trash but must be recycled according to the European WEEE Waste Electrical and Electronic Equipment directive Explanation of symbols Symbols used throughout the manual FN Warning AV Caution Important notice or Note remark Hint tip Additional information Explanation of symbols This page intentionally left blank Introduction This page intentionally left blank Overview Overview Thank you for choosing Barco Single display or complete system This manual describes installation and usage of a complete system A system is a bundling of one or more displays and one or more display controllers graphics boards However if you have purchased the display only instead of a complete system please refer to the chapters in this manual covering the display and disregard the information about the display controller BARCOMED Coronis display controller overview BARCOMED Coronis display controller overview The BarcoMed Coronis display controller delivers a quality image with 1024 simul
42. ption is made for software delivered by BarcoView that would prove to be a cause for the malfunctioning of the hardware covered under this Agreement 2 4 Normal wear and tear use under circumstances exceeding specifications abuse unauthorized repair or alternation lack of proper maintenance 2 5 Any failures resulting from an accident negligence such as but not limited to removing or deleting system files amp licensed software product files misuse circuit failure or any change damage due to fire water thunder or lightning power failure or fluctuation disruption of communication lines or due to force majeure or any reason foreign to the equipment 2 6 Any specific services or procedures asked for by Customer related to verification of repaired equipment ARTICLE 3 OBLIGATIONS OF THE CUSTOMER Customer hereby assumes the following obligations as partial consideration for BarcoView performance of its requirements under the warranty condition failure by Customer to meet its obligations under this paragraph shall excuse BarcoView s performance hereunder 3 1 Customer shall not expose BarcoView personnel to any unsafe working conditions 3 2 Repairs to equipment under warranty resulting from improper maintenance or repair performed by the Customer or its officers 116 Warranty Statement agents employees or representatives shall be borne by the Customer at its additional cost and expense 3 3 The customer is re
43. r computer and disconnect the power cord however make sure that the computer chassis is still grounded 2 Remove the chassis cover according to the manufacturer s instructions Be sure to observe safety warnings 3 If you have decided to use the on board VGA capabilities of the BarcoMed Coronis see Using the VGA capabilities of the BarcoMed Coronis on page 32 you must now remove any VGA display controller s that are currently installed in the computer or disable any VGA controllers that are integrated into your PC s motherboard 4 Install the BarcoMed Coronis Controller into a free PCI slot either 64 bit or 32 bit see figure 5 for examples of slots Be sure that the display controller is seated firmly in the slot 5 Secure the card to the chassis with the PC s 1 0 panel mounting screw and replace the chassis cover 6 Connect the primary display left most display in a linear configuration top most in a vertical configuration to the uppermost connector on the BarcoMed Coronis the output farthest from the motherboard Head 1 in figure 6 using the provided 33 BARCOMED Coronis display controller installation DVI cable For a dual headed BarcoMed Coronis setup connect the secondary display to the other connector on the display controller 7 Replace the chassis cover reconnect the power cord turn on the power and boot the system as usual Running multiple BarcoMed Coronis display controllers in a single
44. ranty or otherwise shall not exceed the price of the item or items of goods or services upon which such liability is based ARTICLE 7 FORCE MAJEURE Either party shall be released from performance of its obligations under this agreement to the extent and for so long as the performance of 117 Warranty Statement this agreement is impeded by reason of force majeure For the purposes of this clause the expression force majeure means but shall not be limited to industrial dispute fire mobilization requisition embargo currency transfer prohibitions insurrection lack of means of transport restrictions of the use of energy and generally any circumstances which are beyond the control of the parties and hinder performance by one party of his obligations ARTICLE 8 GENERAL 8 1 Customer acknowledges its understanding that all software and electronic devices including BarcoView products are subject to possible error mechanical or electrical failure and should not be relied upon in inappropriate applications or without proper backup and or other safety precautions whenever personal injury or property damage may result from failure or error of the product 8 2 BarcoView shall not be responsible for machine failure and or its failure to render service or maintenance due to causes beyond its reasonable control 118 B4100519 03 March 2007 www barco com
45. rd American power cord e Chinese power cord This manual If some of the items are missing please contact the reseller from whom you have purchased the unit 24 Parts controls and connectors Parts controls and connectors Front 1 Figure 1 Front side Power LED The LED is off when the display is disconnected from the power The LED is also off when the LED function is disabled in the on screen display OSD The LED is green when the display is on when enabled in the on screen menus The LED is orange when the display is in Stand by power saving mode USB downstream port See also item 7 on page 26 Control wheel The control wheel can be pressed like a push button and rotated like a knob It allows to put the display in stand by navigate through the on screen display OSD menus and change values in the OSD 25 Parts controls and connectors Rear ANAM 26 Figure 2 Rear side Connector compartment cover To get access to the connectors remove the cover by pulling down the 2 clips at the top of the cover Tilt amp swivel foot cover This cover is packed in a separate box when the display is shipped to the customer Tilt amp swivel foot Slot for security cable e g Kensington lock DVI digital video input USB upstream port Connect this connector to the PC USB bus if you wish to connect USB devices to the display s USB
46. separate boards were installed DICOM DICOM stands for Digital Imaging and Communications in Medicine It is a standard developed by the American College of Radiology ACR and the National Electrical Manufacturers Association NEMA The standard specifies how digital image data can be moved from system to system In addition Supplement 28 Part 14 specifies a function that relates pixel values to displayed Luminance levels and is called Grayscale Standard Display Function 112 tatement 113 Warranty Statement This page intentionally left blank 114 Warranty Statement ARTICLE 1 SERVICES BarcoView warrants that the equipment will be free of defects in workmanship or material for the warranty period Notwithstanding the provisions of clause 2 repair and replacement of defects in material and or workmanship under this warranty shall be accomplished in our works in the following manner 1 1 The Customer upon the occurrence of any equipment failure shall contact BarcoView Customer Support Center or an authorized service center by telephone fax or e mail and shall provide the applicable Customer Support person with a complete description of the problem being encountered including the model and serial number of the equipment in which the problem has arisen 1 2 The Customer Support person shall diagnose the problem experienced by the Customer and shall advise the Customer on how to proceed Customer Support
47. splay operation erreira ie hintaan 71 Display operation sossssseseeseesresresresresrrnsrnrrnsensrn sen sen sen sen sen sen sen sen sen een enn nn 73 Stand by SWItChiNQO sesesesensersensensrnsensensensensensnnnrnnennrnn ennen 73 About the On Screen Display OSD s sesesensensensensensnnsnnsnnnn 74 Locking and unlocking user controls ceeceseseseeseceeeseeeseeeees 75 Complete OSD overview ccccscsesesssssssseseseseseseseseseseseseseseseeees 77 Advanced display Operation sessessessersensersensrnsensrnsrnsrns ennen rnn rn nnn na 79 Introduction arenen a Ea 79 Advanced functions in the Luminance MeNU ceeeeeeee 80 Advanced functions in the Settings MENU smsnn 80 Advanced functions in the Information MENU 81 Advanced functions in the Adjustments Menu 84 MediCal Pro SOftWAFE ou ee eeeseececeececeecececeesscecsececeececescecsacenseceeees 85 MediCal Pro installation and OPeratiON sesesemssemsmsmsmsnn 87 MediCal Pro software installation sesessessessessrossrnsrnnnnn 87 USING Medical PIO 3 cc occes is erect debet aaas 87 Cleaning iMstructiOns visiirisi anasiri iinis 89 PIECAULIONS sweet aed nian eta toes 91 FONE GlaSS Arica ote ach eased ans pita deat naa AEE T 92 GODIN bess stay bred beer ine bet eeni Sa adetincidw alates 93 LCD panel haana a le ie Sane etter Maes 94 Troubleshooting cc ssces cscecsseedsavectacesc
48. sponsible for installing the BarcoView equipment in an environment for which it was intended If there is an indication that the equipment was used even temporary outside its specifications BarcoView is entitled not to perform warranty repairs and terminate the warranty agreement Any actions that have been taken by BarcoView in this respect may be invoiced to the Customer at normal pricing ARTICLE 4 MODIFICATIONS OR CHANGES TO THE EQUIPMENT Customer may make additions to the equipment only with explicit written consent of BarcoView Any attempt to do so voids the warranty ARTICLE 5 DISCLAIMER OF WARRANTIES Barcoview disclaims all warranties expressed or implied including all implied warranties of merchantability and fitness for a particular purpose ARTICLE 6 LIMITATION OF LIABILITY Barcoview shall not under any circumstances be liable to customer or any third party for direct indirect incidental special or consequential damages such as but not limited to damage to or loss of tangible or intangible property or equipment loss of profits or revenues cost of capital cost of purchase of replacement goods or claims of customers of user for service interruptions The liability of BarcoView for manufacturing sale delivery resale installation operation or suitability for use of any products or services covered by or furnished under this warranty condition whether arising out of contract negligence strict tort war
49. storage 109 Technical specifications Item Specification Altitude 7500 m storage 3000 m operation 110 Connector pin assignments Connector pin assignments DVI connector Figure 30 DVI connector pin layout Pin no Signal Pin no Signal 1 TMDS DATA 2 14 5V POWER 2 TMDS DATA 2 15 GND 3 GND 16 HOT PLUG DETECT 4 NC 17 TMDS DATA 0 5 NC 18 TMDS DATA 0 6 DDC CLOCK 19 GND 7 DDC DATA 20 NC 8 NC 21 NC 9 TMDS DATA 1 22 GND 10 TMDS DATA 1 23 TMDS CLOCK 11 GND 24 TMDS CLOCK 12 NC 25 GND 13 NC 111 Glossary Glossary Calibration Each display is calibrated in the factory before it is sent to the customer After this calibration black and white luminance are set to the ideal level A stabilization routine constantly active when the display is on keeps these levels constant using the built in sensor Display Controller head A display controller graphics board converts the digital data from the computer into digital or analog video voltages Most of the common display controllers contain just one set of video and sync outputs However some high end boards like some of the BarcoMed boards contain two sets of video and sync outputs This is called a dual head display controller It is like two complete display controllers implemented on one single unit A dual head board in the computer behaves exactly as if two
50. tached to the BarcoMed display controller you are working with go back to the Settings tab of the Display Properties Control Panel If necssary attach the second display you detached in step 2 above by right clicking on the rectangle that represents it and selecting Attached Now repeat steps 5 8 above for this display If you are using a Quad Head Configuration repeat all of the above steps for the two displays on the second display controller 103 General tips 104 Note If you have a single display configuration and you have enabled DualView Windows will not allow you to attach the second head This is normal and not a bug After enablingDualView and setting the resolutions in a Quad Head Configuration you may need to drag the heads into the proper position in the window on the Settings tab so that the arrangement in the window on the Settings tab matches the physical arrangement of your configuration nformation 105 Technical Information This page intentionally left blank 106 Technical specifications Technical specifications MFGD 2621 Item Specification Picture panel 21 3 inch diagonal viewable screen TFT thin film transistor active matrix gray scale liquid crystal display Resolution Native 1600 x 1200 Display area H x V 432 x 324 mm Viewing angle 10 1 contrast Vertical 170 Horizontal 170 Pixel
51. taneous shades of gray for medical viewing applications Minimum system requirements Pentium II 266 MHz with 128 MB RAM Pentium II 800MHz with 256 MB RAM for cineloops Important Other hardware and software installed in the system may require more system memory for best performance PCI 3 0 compliant slot PCI version or PCle 1 1 compliant slot PCle version Windows XP Professional Windows 2000 Professional Windows 2003 Server Windows XP Professional x64 Edition Windows 2003 Server x64 Edition Features of the BarcoMed Coronis display controller Portrait or landscape Mode Dual Head Configuration e 10 bit in 10 bit out LUT 10 bit performance on LCD 1024 Simultaneous shades of gray Hardware cursor Displays VGA boot messages on Coronis displays 64 bit 66MHz Single slot PCI card PCI version 64MB Video memory PCI version Single slot PCIe x8 card PCIe version 128MB Video memory PCIe version 1 May be installed in a 32 bit 33Mhz PCI slot but with reduced performance 2 May be installed in a PCIe x16 slot however not all PC Bios s support x8 cards in the x16 slot Check with your PC manufacturer 20 BARCOMED CORONIS display controller overview Supported resolutions for each head of the BarcoMed Coronis display controller Coronis 2MP displays 1200 x 1600 60 HZ primary 1600 x 1200 60 HZ Coronis 3MP displays 1536 x 2048 60 HZ primary lt 2048
52. tings in the PC BIOS Nothing happens when you press or rotate the control wheel The User Controls may be disabled Please read the paragraph about the User Controls function The image is non propor tionally spread out over the screen Select another resolution in the Windows Display Properties control panel The image on the screen is rotated 90 Select another resolution in the Windows Display Properties control panel The previous image remains slightly visible on the screen This phenomenon called image sticking is normal if the same image has been on the screen for a long time The ghost image will disappear after some time Over 10 hours operation with the same image content is not recommended Switching on the display DPMS may decrease the risk of image sticking A Slight case of image sticking can be solved by continuously displaying a full white image during a number of hours On a dual head system the images on the left and right display seem to be switched Switch the video cables at the display controller or at the display video inputs 101 General tips 102 Setting the resolution of your Coronis display lt Note In order to set the resolution of your Coronis you must be logged in using an account with administrator privileges Open the Windows Display Control Panel by one of the two methods below a Start gt Settings
53. tion 5 Unplug the LED connection 29 94 LCD panel n Figure 29 To clean the LCD panel 7N Take care not to touch the I quard light sensor on the LCD panel Dust particles on the LCD panel may be blown away by using a dust remover E g DUST OFF 67 KONTAKT Chemie A dust remover is composed of a blend of compressed liquid gases functioning as propellant They provide a jet of dry inert gas that acts like compressed air for a quick and safe removal of dust particles and other dry contaminants on the surface of the Icd panel or the glass panel Attention The dust remover contains a liquid gas If you shake the can or move the can too fast while spraying you may blow drops of liquid on the panel surface If this is the case clean the panel as described below If the LCD panel is dirty or wet clean the panel using a lint free nonabrasive cloth lightly moistened with a solution of 25 Isopropyl Alcohol IPA and 75 de ionized or distilled water E g Cleareen a product of Certified Laboratories In case you do not dispose of these products use plain water instead Take another clean dry soft lint free cloth and gently wipe the glass dry 95 LCD panel 96 This page intentionally left blank oting 97 Troubleshooting This page intentionally left blank 98 General tips General tips If one display from a multi head system exhibits problems try to eliminate th
54. up wizard 3 If necessary align the displays geometry settings 4 For all the displays in the system check if the DPMS setting is turned on Therefore right click on the display icon and select Properties from the drop down menu Then click on Details Check if the Powersave option is checked If not check it This is necessary to use the DPMS possibilities of the display controller 5 For all the displays in the system define if necessary and select a Preset 6 After selecting the Preset MediCal Pro starts consistency calibration automatically 7 Define the Q A task schedule 8 Run the due tasks Please refer to the MediCal Pro User Guide for more information 87 MediCal Pro installation and operation This page intentionally left blank 88 nstructions 89 Cleaning instructions This page intentionally left blank 90 Precautions Precautions Precautions Take care not to damage or scratch the glass or LCD panel Do not apply pressure on the glass or LCD panel Do not apply or spray liquid directly to the glass panel or cabinet as excess liquid may cause damage to internal electronics Instead apply the liquid to the cleaning cloth DO NOT USE Lye or cleaning solutions containing lye Acid Detergents with fluoride Detergents with ammonia Detergents with abrasives Steel wool Sponge with abrasives Cloth with thread made of steel Other
55. x 1536 60 Hz Coronis 5MP displays 2048 x 2560 60 HZ primary 2560 x 2048 60 Hz For all BarcoMed Coronis display controllers The following resolutions are also available on head 1 when the OS is booted in VGA mode e 640x480 Default refresh rate 16 colors 4 bit color grayscale 800x600 Default refresh rate 256 colors 8 bit color grayscale System Configuration Guidelines Because of the low power consumption and low heat generation of the BarcoMed Coronis display controller multiple controllers may be installed in adjacent PCI PCle slots or adjacent to other PCI PCle boards Additionally there should be no need to modify either the PC s power supply and or cooling system 21 BARCOMED CORONIS display controller overview Barco displays overview Barco displays The MFGD 2621 is a 21 inch grayscale LCD display with a native resolution of 1600 x 1200 The MFGD 3621 is a 21 inch grayscale LCD display with a native resolution of 2048 x 1536 Their high brightness combined with image crispness and excellent viewing angle makes them ideal for a multitude of medical applications and environments I Guard I GUARD is Barco s patent pending built in calibration device continuously maintaining image quality With I GUARD QA checks no longer need to disturb normal radiology activities as they can be performed while applications are running I GUARD allows radiologists or QA administrators to
56. y menu is set to Automatic To change the orientation of the image you will have to change the resolution in the Windows Display control panel if possible 43 Power connection Power connection To connect the power 44 3 Figure 14 To get access to the connectors remove the connector compartment cover by pulling down the 2 clips at the top of the cover Connect the output of the 12V DC power supply to the DC input of the display Connect one end of the proper power cable to the AC input of the 12V DC power supply Connect the other end of the power cord to a grounded power outlet Video connection Video connection Connecting DVI cables One display Figure 15 1 Connect one end of the DVI cable to the DVI input of the display 2 Connect the other end of the DVI cable to the DVI connector of the display controller board If this board has 2 video heads 2 video outputs connect to output Vid 1 Head A Connecting DVI cables Two displays 1 Connect the left display when looking at the front side to display controller output Vid 1 Head A as described above 2 Connect the second display to output Vid 2 Head B 45 USB connection USB connection The USB connection allows you to use the display as USB hub to which you can connect USB devices such as a keyboard mouse or digital camera
57. y time but it is more convenient to select landscape or portrait orientation before connecting the cables Figure 9 Figure 10 Portrait Landscape orientation orientation To change the panel orientation 1 Stand at the front side of the panel and take the panel at both sides iD Very important Tilt the panel before changing the orientation Should you change the panel orientation without tilting it first you might irreversibly damage the tilt amp swivel mechanism 41 After unpacking the display Figure 11 Tilt the panel before rotating 3 To change from portrait to landscape turn the panel counterclockwise Figure 12 To rotate the panel from portrait to landscape 4 To change from landscape to portrait turn clockwise Notice If after installing the display or the system you change the panel orientation while an image is on the screen the result depends on your application 42 After unpacking the display In a Coronis system the image orientation will adapt to the new panel orientation automatically after a second If the I switch software is installed and enabled the image resolution will also be adapted automatically to the new panel orientation e If you use the display stand alone the image orientation will not change with the panel orientation Only the orientation of the on screen display OSD will change automatically in case Orientation in the OSD Geometr

Barco MFGD 3621 Projector Accessories User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents