Home
Asus P5LP-LE Computer Hardware User Manual
Contents
1. Installing DDR2 DIMMs other than the recommended configurations may cause memory sizing error or system boot failure Use any of the recommended configurations on the next page e Install only identical the same type and size DDR2 DIMM pairs using the recommended configurations e Make sure that the memory frequency matches the CPU FSB Front Side Bus Refer to the Memory frequency CPU FSB synchronization table on the next page e This motherboard does not support double sided 16 bit DDR DIMMs e Do not create a three DIMM configuration in dual channel mode The third DIMM is ignored in the dual channel operation ASUS P5LP LE Leonite Recommended memory configurations Single channel Sockets DIMM2 DIMM3 Installed Installed Installed Installed Dual channel Installed Installed Installed Installed Installed Installed Installed Installed Use only identical DDR2 DIMM pairs Memory frequency CPU FSB synchronization CPU FSB 1066 MHz DDR DIMM Type Memory Frequency PC2 5300 PC2 4200 667 533 MHz 800 MHz PC2 5300 PC2 4200 PC2 3200 667 533 400 MHz 533 MHz PC2 5300 PC2 4200 PC2 3200 667 533 400 MHz ASUS P5LP LE Leonite 3 2 Installing a DDR2 DIMM Unplug the power supply before adding or removing DIMMs or other system components Failure to do so can cause severe damage to both the motherboard and the components To install a D
2. N y 5095899 GND RSATA TXP4 GND RSATA RXP4 GND RSATA RSATA_RXN4 SATA1 SATA3 oeoaooo OrzOLzo gp39823229 aN Important notes on Serial ATA e Install the Windows 2000 Service Pack 4 or the Windows XP Service Pack1 before using Serial ATA e When using the connectors in Standard IDE mode connect the primary boot hard disk drive to the SATA1 connector Refer to the table below for the recommended SATA hard disk drive connections Serial ATA hard disk drive connection Connector Setting Black Master Boot Disk White Master Boot Disk Blue Slave Data Disk Yellow Slave Data Disk ASUS P5LP LE Leonite 17 5 IEEE 1394a connector 10 1 pin F_1394 This connector is for an IEEE 1394a port Connect the IEEE 1394a module cable to this connector then install the module to a slot opening at the back of the system chassis NEVER connect USB cable to the IEEE 1394 connector Doing so will damage the motherboard 6 USB connectors 10 1 pin FRONT_USB1 FRONT USB2 These connectors are for USB 2 0 ports Connect the USB GAME module cable to any of these connectors then install the module to a slot opening at the back of the system chassis These USB connectors comply with USB 2 0 specification that supports up to 480 Mbps connection speed P5LP LE Leonite USB 2 0 connectors N Never connect a 1394 cable to the USB connectors Doing so will damage the mo
3. for about 5 10 seconds then move the cap back to pins 2 3 3 Plug the power cord and turn ON the computer Hold down the lt Del gt key during the boot process and enter BIOS setup to re enter data Except when clearing the RTC RAM never remove the cap from the default position Removing the cap will cause system boot failure Clear CMOS Normal P5LP LE Leonite Default Clear RTC RAM Clear password 3 pin CLPWD This jumper allows you to clear the password if you forgot your password Clear Password Normal Default P5LP LE Leonite Clear password setting ASUS P5LP LE Leonite 11 6 Connectors 6 1 Rear panel connectors 15 14 13 12 11 10 1 PS 2 mouse port green This port is for a PS 2 mouse 2 IEEE 1394a port This 6 pin IEEE 1394a port provides high speed connectivity for audio video devices storage peripherals PCs or portable devices 3 LAN RJ 45 port This port allows connection to a Local Area Network LAN through a network hub 4 Side Speaker Out port gray This port connects to the side speakers in an 8 channel audio configuration 5 Rear Speaker Out port black This port connects to the rear speakers on a 4 channel 6 channel or 8 channel audio configuration 6 Center Subwoofer port yellow orange This port connects the center subwoofer speakers 7 Line In port light blue This port connects a tape CD DVD player or other audio sources 8 Line O
4. DJLOCIOUIOIN E2905 First Edition V1 October 2006 Contents P5LP LE Leonite specifications summary ii 1 Motherboard layout 2 Central Processing Unit CPU 2 3 System 5 4 Expansion 8 5 SSMO RR T T py 11 6 ORBE LOLS aute rortufrin dra E EUER 12 6 1 Rear panel connectors 12 6 2 Internal in nn En EE 14 P5LP LE specifications summary CPU LGA775 socket for the Intel Pentium 4 and Conroe processor in the 775 land package Chipset Northbridge Intel 945G Graphics Memory and Controller Hub GMCH Southbridge Intel ICH7DH Front Side Bus 1066 MHz FSB Memory Dual channel memory architecture 4 x 240 pin DIMM sockets support unbuffered non ECC 4 GB 667 533 400 MHZ DDR2 memory modules Expansion slots 1 x PCI Express x16 slot for discrete graphics card 3 x PCI slots Rear panel 1 x PS 2 keyboard port 1 x PS 2 mouse port 1 x IEEE 1394a port 1 x LAN RJ 45 port 6 x audio ports support 8 channel audio configuration 4 x USB 2 0 ports support hot plug function 1 x VGA port 1 x Coaxial SPDIF out port 1 x Coaxial SPDIF in port Internal connectors 1 x Floppy connector 1 x IDE connector 1 x 24 pin ATX power connector 1 x 4 pin ATX 12 V power connector 4 x Serial ATA conne
5. E Leonite 16 ATX power connectors 24 pin ATXPWR 4 pin ATX12V These connectors are for an ATX power supply The plugs from the power supply are designed to fit these connectors in only one orientation Find the proper orientation and push down firmly until the connectors completely fit aN e Do not forget to connect the 4 pin ATX 12 V power plug otherwise the system will not boot up e Make sure that your ATX 12V power supply can provide 8A on the 12V lead and at least 1A on the 5 volt standby lead 5VSB The minimum recommended wattage is 230W or 300W for a fully configured system The system can become unstable and might experience difficulty powering up if the power supply is inadequate e You must install a PSU with a higher power rating if you intend to install additional devices ATXPWR ATX12V 3 Volts _ 3 Volts GND 12V pc 12 Volts ae ge 3 Volts du Ground i Ground P5LP LE Leonite ATX power connectors PSON e Ground Ground _ Ground il 5 Volts 5 Volts e 5 Volts 5 Volts ee Ground Am EE 5 Volts E Ground 5 Volts gw Ground EE Power OK 412 Volts 12 Volts E 3 Volts ASUS P5LP LE Leonite E 5V Standby 4 Serial ATA connectors 7 pin SATA1 black SATA2 white SATA3 blue SATA4 yellow These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives SATA2 SATA4 1 1 NA
6. IMM e DDR2 DIMM notch 1 Unlock a DIMM socket by M pressing the retaining clips r TT Wi e outward 2 Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket 3 Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated Unlocked retaining clip MN e A DDR2 DIMM is keyed with a notch so that it fits in only one direction Do not force a DIMM into a socket to avoid damaging the DIMM e The DDR2 DIMM sockets do not support DDR DIMMs Do not install DDR DIMMs to the DDR2 DIMM sockets 3 5 Removing a DDR2 DIMM To remove a DIMM 1 Simultaneously press the retaining clips outward to unlock the DIMM N Support the DIMM lightly with your fingers when pressing the retaining clips The DIMM might get damaged when it flips out with extra force DDR2 DIMM notch 2 Remove the DIMM from the socket ASUS P5LP LE Leonite 4 Expansion slots In the future you may need to install expansion cards The following sub sections describe the slots and the expansion cards that they support 4 Make sure to unplug the power cord before adding or removing expansion cards Failure to do so may cause you physical injury and damage motherboard components 4 1 Installing an expansion card To install an expansion card 1 Before installing the expansion card read the documentation that came wi
7. OPPY This connector is for the provided floppy disk drive FDD signal cable Insert one end of the cable to this connector then connect the other end to the signal connector at the back of the floppy disk drive Pin 5 on the connector is removed to prevent incorrect cable connection when using an FDD cable with a covered Pin 5 FLOPPY a NOTE Orient the red markings on the floppy ribbon cable to PIN 1 P5LP LE Leonite Floppy disk drive connector ASUS P5LP LE Leonite 2 IDE connector 40 1 pin IDE This connector is for an Ultra DMA 100 66 signal cable The Ultra DMA 100 66 signal cable has three connectors a blue connector for the primary IDE connector on the motherboard a black connector for an Ultra DMA 100 66 IDE slave device optical drive hard disk drive and a gray connector for an Ultra DMA 100 66 IDE master device hard disk drive If you install two hard disk drives you must configure the second drive as a slave device by setting its jumper accordingly Refer to the hard disk documentation for the jumper settings e Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector This prevents incorrect insertion when you connect the IDE cable e Use the 80 conductor IDE cable for Ultra DMA 100 66 IDE devices IDE NOTE Orient the red markings usually zigzag on the IDE ribbon cable to PIN 1 P5LP LE Leonite IDE connector Pini ASUS P5LP L
8. OS Real Time Clock SCI IRQ used by ACPI Bus Intel PCI Express Root Port Intel VGA Controller Intel ICH7DH High Definition Audio Controller Intel USB Universal Host Controller VIA OHCI Compliant IEEE 1394 Host Controller Intel ICH7DH Integrated LAN Controller Microsoft Port Mouse Numeric Data Processor Intel USB Universal Host Controller Intel Ultra ATA Storage Controllers Intel SMBus Controller PCI slot 1 PCI slot 2 PCI slot 3 Onboard LAN Onboard 1394 controller ASUS P5LP LE Leonite PCI Express slot This motherboard has one PCI Express slot which supports a 164 pin x16 interface graphics card PCI slots There are three 32 bit PCI slots on this motherboard The slots support PCI cards such as a LAN card SCSI card USB card and other cards that comply with PCI specifications ASUS P5LP LE Leonite Clear RTC RAM 3 CLRTC This jumper allows you to clear the Real Time Clock RTC RAM in CMOS You can clear the CMOS memory of date time and system setup parameters by erasing the CMOS RTC RAM data The onboard button cell battery powers the RAM data in CMOS which include system setup information such as system passwords To erase the RTC RAM 1 Turn OFF the computer and unplug the power cord 2 Move the jumper cap from pins 2 3 Normal to pins 1 2 Clear CMOS Keep the cap on pins 1 2
9. ctors 1 x IEEE 1394a connector 2 x USB 2 0 connectors 1 x CPU fan connector 1 x System fan connector 1 x Internal audio connector 1 x Digital audio connector 1 x Front headphone connector 1 x System panel connector Storage Southbridge supports 2x Ultra DMA 100 66 hard disk drives 4 Serial ATA hard disk drives with hot swap function continued on the next page P5LP LE specifications summary Southbridge supports 8 channel audio configuration with Intel High Definition Audio CODEC Realtek ALC888 High Definition Audio CODEC LAN Intel 82562GT 10 100 Mbps Fast Ethernet LAN PHY IEEE 1394 Agere LFW3227 two IEEE 1394a ports PC health ASUS F8000 for CPU system and chassis fan monitoring control motherboard and CPU temperature BIOS features 4 Mb SPI Flash ROM HP BIOS with enhanced ACPI DMI Green and PnP Features Plus Form factor Micro ATX form factor 9 6 in x 9 6 in Specifications are subject to change without notice 1 Motherboard layout 24 5cm 9 6in PS 2KBMS T Mouse B Keyboard Top Subwoofer Speaker Out Center Top Line In Rear Speaker Out Ji Below Center Line Out Side Speaker Out Below Mic In PCIEX16 PCl2 Agere LFW3227 PC3 F LINE IN Ta i i HHH ASUS P5LP LE Leonite ATXPWR gt n O i DDR2 XMM1 64 bit 240 pin module P5LP LE CR2032 3V Lithium Cell CMOS Power Int
10. el CLRTC ICH7DH SATA2 SATA4 SATA1 SATA3 FRONT_USB1 oT MEFE LEERE HARA FRONT_USB2 24 5cm 9 6in 2 AN Central Processing Unit CPU The motherboard comes with a surface mount LGA775 socket designed for the Intel Pentium 4 and Conroe processor in the 775 land package Your boxed Intel Pentium 4 processor package should come with installation instructions for the CPU heatsink and the retention mechanism If the instructions in this section do not match the CPU documentation follow the latter Upon purchase of the motherboard make sure that the PnP cap is on the socket and the socket contacts are not bent Contact your retailer immediately if the PnP cap is missing or if you see any damage to the PnP cap socket contacts motherboard components ASUS will shoulder the cost of repair only if the damage is shipment transit related Keep the cap after installing the motherboard ASUS will process Return Merchandise Authorization RMA requests only if the motherboard comes with the cap on the LGA775 socket The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation removal or misplacement loss incorrect removal of the PnP cap Installing the CPU To install a CPU 1 Locate the CPU socket on the motherboard P5LP LE Leonite CPU Socket 775 Before installing the CPU make sure that the socket box is facing towards you and the load lever is on your lef
11. is for a chassis mounted front panel headphone port 1 QNO qudd P5LP LE Leonite Front panel audio connector 20 ASUS P5LP LE Leonite 11 System panel connector 10 1 pin F_PANEL This connector supports several chassis mounted functions TE Reset Ground HDLED HDLED O 2 F PANEL HAAR P5LP LE Leonite System panel connector GND PWR PLED PLED e System power LED This 2 pin connector is for the system power LED Connect the chassis power LED cable to this connector The system power LED lights up when you turn on the system power and blinks when the system is in sleep mode e Hard disk drive activity This 2 pin connector is for the HDD Activity LED Connect the HDD Activity LED cable to this connector The IDE LED lights up or flashes when data is read from or written to the HDD e Power Soft off button This connector is for the system power button Pressing the power button turns the system ON or puts the system in SLEEP or SOFT OFF mode depending on the BIOS settings Pressing the power switch for more than four seconds while the system is ON turns the system OFF e Reset button This 2 pin connector is for the chassis mounted reset button for system reboot without turning off the system power ASUS P5LP LE Leonite 21 22 ASUS P5LP LE Leonite
12. systems disable the Hyper Threading Techonology item in the BIOS to ensure system stability and performance Installing Windows XP Service Pack 1 or later version is recommended Make sure to enable the Hyper Threading Technology item in BIOS before installing a supported operating system For more information on Hyper Threading Technology visit www intel com info hyperthreading To use the Hyper Threading Technology on this motherboard iF Install an Intel Intel Pentium 4 processor that supports Hyper Threading Technology Power up the system and enter the BIOS Setup Under the Advanced Menu make sure that the item Hyper Threading Technology is set to Enabled The item appears only if you installed a CPU that supports Hyper Threading Techonology Reboot the computer ASUS P5LP LE Leonite 3 System memory The motherboard comes with four Double Data Rate 2 DDR2 Dual Inline Memory Module DIMM sockets A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240 pin footprint compared to the 184 pin DDR DIMM DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket The following figure illustrates the location of the DDR2 DIMM sockets P5LP LE Leonite 240 pin DDR2 DIMM sockets XMM1 XMM2 XMM3 XMM4 3 1 Memory configurations You can install 256 MB 512 MB and 1 GB DDR2 SDRAM DIMMs into the DIMM sockets using the memory configurations in this section RA e
13. t ASUS P5LP LE Leonite 2 Press the load lever with your thumb A then move it to the left B until it is released from the retention tab Retention tab Load lever PnP cap This side of the socket box should face you prevent damage to the socket pins do not remove the PnP cap unless you are installing a CPU 3 Lift the load lever in the direction of the arrow to a 135 angle 4 Lift the load plate with your thumb and forefinger to a 100 angle A then push the PnP cap from the load plate window to remove B 5 Position the CPU over the socket making sure that the gold triangle is on the bottom left corner of the socket The socket alignment key should fit into the CPU notch Gold triangle mark Alignment key ASUS P5LP LE Leonite N Close the load plate A then push the load lever B until it snaps into the retention tab The CPU fits in only one correct orientation DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU Notes on Intel Hyper Threading Technology AA This motherboard supports Intel Pentium 4 processor in the 775 land package with Hyper Threading Technology Hyper Threading Technology is supported under Windows XP 2003 Server and Linux 2 4 x kernel and later versions only Under Linux use the Hyper Threading compiler to compile the code If you are using any other operating
14. th it and make the necessary hardware settings for the card 2 Remove the system unit cover if your motherboard is already installed in a chassis 3 Remove the bracket opposite the slot that you intend to use Keep the screw for later use 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot 5 Secure the card to the chassis with the screw you removed earlier Replace the system cover 4 2 Configuring an expansion card After installing the expansion card configure it by adjusting the software settings 1 Turn on the system and change the necessary BIOS settings if any 2 Assign an IRQ to the card Refer to the tables on the next page 3 Install the software drivers for the expansion card When using PCI cards shared slots ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments otherwise conflicts will arise between the two PCI groups making the system unstable and the card inoperable Refer to the table on the next page for details ASUS P5LP LE Leonite Standard interrupt assignments Standard Function System Timer Standard 101 102 key or Microsoft Natural PS 2 Keyboard Programmable Interrupt Controller Intel USB Enhanced Host Controller Intel USB Universal Host Controller Intel USB Universal Host Controller Standard Floppy Disk Controller ECP Printer Port System CM
15. therboard 18 ASUS P5LP LE Leonite 7 CPU and System fan connectors 4 pin CPU_FAN 3 pin SYS_FAN3 The fan connectors support cooling fans of 350 mA 740 mA 8 88 W max or a total of 1 A 2 22 A 26 64 W max at 12 V Connect the fan cables to the fan connectors on the motherboard making sure that the black wire of each cable matches the ground pin of the connector Do not forget to connect the fan cables to the fan connectors Insufficient air flow inside the system may damage the motherboard components These are not jumpers DO NOT place jumper caps on the fan connectors CPU FAN SYS_FANS TI 5 c O2 SAS z95 O O 0 O ERI P5LP LE Leonite Fan connectors 8 Internal audio connector F LINE IN This connector allows you to receive stereo audio input from sound sources such as a CD ROM TV tuner or MPEG card F LINE IN Ek SENSE 2a AUX RCR E P5LP LE Leonite Internal audio connector ASUS P5LP LE Leonite 19 9 Digital audio connector 3 pin SPDIF2 This connector is for an additional Sony Philips Digital Interface S PDIF port s Connect the S PDIF module cable to this connector then install the module to a slot opening at the back of the system chassis The S PDIF module is purchased separately SPDIF2 White 45V L SPDIF_OUT GND f P5LP LE Leonite Digital audio connector 10 Front panel audio connector 10 1 pin F_AUDIO This connector
16. ut port lime This port connects a headphone or a speaker In 4 channel 6 channel and 8 channel mode the function of this port becomes Front Speaker Out 9 Microphone port pink This port connects a microphone ASUS P5LP LE Leonite Audio 2 4 6 or 8 channel configuration Headset 2 channel 4 channel 6 channel 8 channel Light Blue Line In Line In Line In Line In Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out Pink Mic In Mic In Mic In Mic In Yellow Orange Center Subwoofer Center Subwoofer Black Rear Speaker Out Rear Speaker Out Rear Speaker Out Gray Side Speaker Out 10 USB 2 0 ports 3 and 4 These two 4 pin Universal Serial Bus USB ports are available for connecting USB 2 0 devices 11 USB 2 0 ports 1 and 2 These two 4 pin Universal Serial Bus USB ports are available for connecting USB 2 0 devices 12 Video Graphics Adapter port This 15 pin port is for a VGA monitor or other VGA compatible devices 13 Coaxial S PDIF Out port This port connects an external audio output device via a coaxial S PDIF cable 14 Coaxial S PDIF In port This port connects an external audio input device via a coaxial S PDIF cable 15 PS 2 keyboard port purple This port is for a PS 2 keyboard ASUS P5LP LE Leonite 13 6 2 Internal connectors This section describes and illustrates the internal connectors on the motherboard 1 Floppy disk drive connector 34 1 pin FL
Download Pdf Manuals
Related Search
Related Contents
«Mode d`emploi » de l`expérimentation tablettes DCN-SWWA Webcast application Avocent AMX AMX5000 Siemens WinCC Flexible 2005 Micro User Manual CODICE – Acuerdo de Licencia para Usuario Final Mise en page 1 太陽光発電系統連系用漏電ブレーカの選定変更のお知らせ V7 Metro Anti-Slip Case for iPhone 6 Plus - White Lexmark 2I1 Printer User Manual Copyright © All rights reserved.