Apple FB147LL/A MP3 Player User Manual
Contents
1. Under Hood Connections Route the hood pin and tach wires through the firewall into the engine compartment Always try to pull the wires through a factory rubber grommet If drilling through the firewall BE CAREFUL Check for obstructions on both sides of the firewall After drilling use a snap in grommet to protect the wires from sharp edges Installing the External Long Range Antenna To insure the best possible reception place the antenna in the center of the windshield behind the rear view mirror Before attaching to the glass ensure that the surface is clean and dry For best results with range place the antenna below the tint screen Run the cable under the headliner and behind the A pillar panel Be careful not to pinch the antenna cable Plug the antenna into the BLUE connector on the Control Module NOTE This step is not used on Alarm Only Units with no External Antenna Mounting The Control Module Never mount the module in the engine compartment Select a location under the dash to install the main module Be certain that the module is securely attached and does not obstruct any serviceable areas Do not force or jam the module into tight places instead of mounting The module must be free from all moving parts such as brake and clutch as gas pedals linkages Do not place the module directly in front of a heater vent Testing The System When the installation is complete it will be necessary to test that the system is w2. Installation Guide d B50 INSTALLATION TIP Components Control module Remote transmitter s Antenna with built in Program Button and LED s 6 pin main harness with dual 30amp power inputs 11 pin harness 5 pin harness 3 pin keyless entry harness Hood pin safety switch Cold Start Temperature Sensor Installation and Owners Manual Recommended Pre Installation Procedures BEFORE STARTING INSTALLATION Discuss the optional features with the customer Take a few minutes to review the installation and owners manuals Check if the vehicle has a factory security or anti theft system If equipped inform the customer of addition parts and labour Do a walk around the vehicle and check for any damage If installing a LED discuss the placement with customer before installing Note This remote starter is designed for fuel injected and diesel engines NEVER INSTALL AUTOMATIC TRANSMISSION STARTER IN AMANUAL TRANSMISSION VEHICLE Recommended Installation Procedures Proper Connections Remote Starters can handle loads of up to 30 amps for extended periods of time It is CRITICAL to insure that ALL high current connections are properly soldered and insulated with quality electrical tape Failing to insure proper connections will result in warranty being VOID and can result ina FIRE The manufacturer is not responsible for any such damages It only takes a few more minutes to do the job RIGHT
3. 3 Start the vehicle LED s on antenna will come when proper tach signal is detected then after 30 35 seconds the park lights will turn off then flash twice to confirm tach learning Note A system reset must be done before a new tach signal can be learned to the module Setting 1 Method 2 Low Idle Learn This option is used for vehicles that maintain a High or Erratic idle after starting and need more than 10 seconds to establish a stable idle Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program Button on the antenna 1 time Step 2 Enter Program Menu 4 Press the button on the remote Button 4 Step 3 Start Vehicle Using the ignition key make sure not to turn the key off at any time or your will exit programming Step 4 Press the Button One time Led will start flashing in single cycles then press and hold Program Button for 5sec Step 5 Release the Button Led should come on steady to indicate correct tach signal the park light will flash to confirm Setting 2 Adjust For Over Crank Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program button on the antenna 1 time Step 2 Enter Program Menu 4 Press the button on the remote Button 4 Step 3 Press the Program Button 2 times Led will start flashing 2 times Step 4 Hold the Program Button For 5 seconds until park lights flash each time lights flash the setting is reduced Step 5 Release
4. Output Ignition 1 BLUE 6 500ma Output Factory Re arm YELLOW m 500ma Output Trunk Release RED WHITE 500ma Output Factory Disarm BROWN 500ma Output CE When Running Armed GRANGE 4 500ma Output C Horn Honk WHITE BLUE m Negative Input Park Brake BLACK WHITE m Positive Input Door Trigger PURPLE I Positive Output Park Lights were Negative Input Hood Pin Switch GREEN WHITE 1 Negative Input Door Trigger GREEN m Negative Input Ground BLACK Negative Output When Running Wiite Vicict m orjinput_ Glow Plug Diesel sLue n AIC Input Tach Detection BLUE WHITE Positive Input Brake Switch Pink m These connection s are only necessary for installation s on manual transmission vehicles LD 500ma Output Door Lock Green Voltage Inverter Output Rea 3 PIN C 500ma Output Door Uniock Brue RED no Program Button Status Led s me oe ACTIVE RF ANTENNA 3 4PIN Blue m i The antenna Must be connected for the system to operate Negative Output Sensor Ground Output Negative Input Input Trigger To Start Output on White wire Jumper position Second Starter Position 1 Second Accessory Position 2 Second Ignition Position 3 The jumpers control the output from the white wire from the six pin harness Place the jumpers in the following order to change the output Note The default setting is second ignition I T
5. INSTALLATION GUIDE a Advanced Remote Vehicle Starting System AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW ULTRASTARTERS COM aa e a ATTENTION FCC ID Notice The system must be placed into Service Mode before any service work is started on This device complies with Part 15 of the FCC rules Operation is the vehicle It is the sole responsibility of the vehicle owner to ensure that this is done subject to the following conditions The manufacturer accepts no liability or responsibility for accidental starting of the 1 This device may not cause harmful interference and vehicle 2 This device must accept any interference received including CARBON MONOXIDE Never Start In A Enclosed Building Garage Carport etc interference that may cause undesired operation The Hood Pin Safety Switch Must Always Be Installed CAUTION Changes or modifications not expressly approved by Never Install Automatic Transmission Remote Starters On Manual Transmission the part responsible for compliance void the user s authority to Vehicles operate this devise Installation Guide d B50 TABLE OF CONTEN 1350 Wiring Diagram Page 3 Pre Installation Page 4 Components Pre Installation Check Installation Procedures Wire Connectors Page 5 6 Pin Connector 11 Pin Connector 5 Pin Connector 4 Pin Connector Jumper Positions Installation Page 6 Basic Installation Quick start Plug In The Module Aut
6. Is Complete a NOTES 1 If the unit does not start check the starter is not in Tach Lock Out or in Program Mode If the vehicle still does not start check all connections and check for factory security Installation Guide f Programming Overview Program mode allows you to adjust the settings and options of your system 7 Your system has been intelligently designed by installers with years of experience The system s default settings do not require any program changes in most cases However this system does incorporate a high advanced programming system that includes 4 menus with numerous options and settings that can be easily adjusted for custom installations and applications User Settings Page 8 This program menu contains settings that adjust the way the system operates for the user Additional Settings Page 8 This program menu contains settings that control addition user options Starter Settings Page 9 This menu controls features and settings associated with remote car starter applications Tach Settings Page 10 This menu allows the programming of the tach signal and the manual adjustment of that setting Entering Program Mode To Enter Program Mode 1 Make sure ignition is in the off position 2 Within three seconds turn the key ON OFF ON OFF ON Leave in the ON position 3 Press and release the Program Button on the antenna 1 time 4 Park lights will come on and the horn optional will honk to co
7. Lock amp Unlock chirps Disabled 1 Flash Honks for Panic and Car Finder Mode only 2 Lock amp Unlock chirps Enabled 2 Flashes Honks for Lock Unlock Panic and Car Finder Mode Only 3 All chirps enabled 3 Flashes Honks for Lock Unlock Start Panic and Car Finder Mode Press the Program Button 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 3 Door Lock Options 1 Double Pulse Unlock 1 Flash Single 75sec Lock pulse and double Unlock Pulse 23 Second Lock amp Unlock 2 Flashes 3 second pulses for Lock amp Unlock 3 0 75 Second Pulses 3 Flashes 0 75 second pulses for Lock and Unlock See setting 4 for door unlock and disarm output durations Press the Program Button 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 4 Door Unlock amp Disarm Pulse Duration TT 1 Short Pulses 1 Flash 125ms pulses with Unlock and on the disarm output 125 second 2 Normal 2 Flashes 750ms pulses with Lock Unlock and on disarm output 75 se
8. Program Button Press momentarily to move to next program step or repeat to change selection Setting 3 Rearm Output Yellow Wire on 14 Pin 1 Type 1 1 Flash Pulse after start and with lock 2 Type 2 2 Flashes Pulse after start only 3 Factory Re arm 3 Flashes 0 75 second pulse with lock and after shutdown Press the Program Button 3 times to select setting 3 This will be confirmed by 3 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 4 Run Time 1 30 Min Run Time 1 Flash Remote Starter runs for 30min when activated 245 Min Run Time 2 Flashes Remote Starter runs for 45min when activated 3 15 Min Run Time 3 Flashes Remote Starter runs for 15 min when activated Press the Program Button 4 times to select setting 4 This will be confirmed by 4 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 5 Maximum Crank Time 110 Seconds 1 Flash 10 sec Max time that starter will stay engaged 23 Seconds 2 Flashes 3 sec Max time that starter will stay engaged 3 5 seconds 3 Flashes 5 sec Max time that starter will stay engaged Press the Program Button 5 time
9. UST BE CONNECTED Green Door Negative Door Trigger Input Manual Transmission Models Only Black Ground System Ground Input MUST BE CONNECTED 4 Pin Connector White Violet Running Output while running Output for security bypass modules Blue Glow Plug Diesel Glow plug input Positive or Negative Programmable Blue White Tach Tach Signal Input MUST BE CONNECTED Pink Brake Positive Brake Input MUST BE CONNECTED 3 Pin Connector Red Green Door Lock Door Lock Output Programmable Menu 1 Setting 3 Red 12vlt Output Output for Voltage Inverter Only Blue Door Unlock Door Unlock Output Programmable Menu 1 Setting 3 2 Pin Connector NIA Ground Ground output for Temperature Senor NIA Temp Sensor Input Trigger To Start 4 Pin Connector Blue Antenna Program Button Connector The Antenna Must Be Connected Before the System will Operate Jumper Selectable Output This output is designed to power addition ignition circuits Most new vehicles will have either a second ignition accessory or starter wire that must be energized Connect the white wire from the 6 pin connector to the additional circuit and set the jumper for the appropriate output Position One Second Starter Output From The White Wire On The 6 Pin Connector Position Two Second Accessory Output From The White Wire On The 6 Pin Connector Position Three Second Ignition Output From The White Wire On The 6 Pin Connector The Defa
10. al the same number of times as the events in memory Maximum four events four honks NOTE If the horn does not honk there are no events in memory Step 3 Press the Program Button once to view the last shut down code The optional Horn willhonk once to confirm code one If the horn does not honk there are no codes in memory Step 4 The LED s on the antenna will flash a code corresponding to a shut down trigger Press the Program Button again to check the second code The horn will honk twice to confirm code two Step 5 To Clear Diagnostic Memory While in Diagnostic Mode press and hold the Program Button for five seconds The park lights will flash and the horn optional will honk once NOTE Once diagnostic memory has 4 shutdown events in memory the system will not record any further shutdown events until the system memory has been cleared Installation Guide ss S 30amp Output Starter YELLOW 30amp Output Heater GREEN 1 gt qj 30amp Input Power RED 2 3 5 8 30amp Input Power RED h 4 l Ba 4 d a 30amp Output Jumper Selectable WHITE 5 bd 30amp
11. cond Press the Program Button 7 times to select setting 7 This will be confirmed by 7 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Note Programming this option will change the pulse length of this output from 750ms to a Much shorter pulse of 125ms PROGRAM MODE 2 ADDITIONAL Setting 1 Secure Valet Mode m 1 Secure Valet Active 1 Flash Valet only if ignition ON and Program Button is held for 15 seconds 2 Normal Valet Active 2 Flashes Valet if ignition ON and Program Button is held for 5 seconds Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 2 Parking Light Output 1 30 Second Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm 2 Negative Park Light 2 Flashes Switches the Park Light and the Trunk Release 3rd Ch Outputs 3 Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm Press the Program Button 2 times to select setting 2 This will be confirmed by 2 LED flashes Press and hold the Program Button until you receive the appropriate of park ligh
12. ected the horn will honk 2 times Battery Replacement The transmitter battery should be changed at least once every year to maintain proper operating range Replace with quality23A 12volt Alkaline battery Step 1 Step 2 step 3 Carefully remove the Remove top case Replace top case Test remote for screw from back of then replace the Re install screw proper operation Step 4 the remote battery i 12 Installation Guide d B50 RELAY DIAGRAM Use 30A SPDT Automotive Type Relays Negative Type Door Locks Iel Vehicle Lock To Control i Lock Unlock D Relay or Switch n Actuators lock Green TET Blue Positive Type Door Locks Fused 12V Un Vehicle L lock Leck Lock Unlock TE Switch Green fo h Blue LE be bet raed s To Control Relay Note Always install a in line fuse when suppling 12volts to relays or Actuator Never use the center pin of the keyless entry harness to power relays 5 Wire Reverse Polarity Type Door Locks Fused 12V Green Blue Lock Vehicle Lock Unlock Switch Enloe EA Note Always install a in line fuse when suppling 12volts to relays Never use the center pin of the keyless entry harness to power relays
13. gram Button until the parking lights horn confirm the selected setting The part lights will flash and the horn optional will honk to indicate the option selected within the setting 5 Turn the ignition key Off to exit Program Mode NOTE This procedure is listed in detail below each program setting on pages 8 10 of this manual SYSTEM RESET STEP 1 Within 3 seconds turn the key ON OFF ON OFF ON Leaving Key ON STEP 2 Press and release the Program Button STEP 3 Park Lights will come ON STEP 4 Press the Program Button a second time and hold for 8 seconds until the park lights flash 3 Times and horn Optional honks 3 times System is now re set to factory defaults Installation Guide d BS PROGRAMMING PROGRAM MODE 1 USER SETTINGS Setting 1 Ign 1 Ignition Lock amp Unlock Enabled 1 Light Flash Doors Lock Unlock when the key is turned On Off 2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only 3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 2 Horn Honk Settings ion Auto Lock 1
14. nfirm entering Program Mode 5 Select Desired Program Menu by the following Press Button 1 Lock User Options See Page 8 Press Button 2 Unlock Additional Options See Page 8 Press Button 3 Start Remote Start Options See Page 9 Press Button 4 Aux Tach Adjustment Menu See Page 10 6 The selected mode will be confirmed by a horn honk if connected and one park light flash 7 The Program Menu may be changed at any time by pressing the transmitter buttons as above this allows the installer to change a setting from one menu then quickly jump to another menu and change another setting without re entering the Program Mode 8 Turning off the ignition or 30 seconds of no activity will exit the Program Mode This will be confirmed by 1 long horn honk and park light flash Note f unit does not enter Program Mode turn ignition off for 5 seconds and repeat steps 1 4 The first ignition Blue MUST be connected to the vehicle s first ignition wire If it is not connected it will not be possible to enter the Program Modes Changing the Programmable Settings To Select and Change A Program Setting 1 Enter Program Mode 2 Select the desired Program Menu See pages 8 10 3 Press amp release the Program Button the correct number of times to select the desired Program Setting as listed on pages 8 10 The park lights will flash and the horn optional will honk to indicate the current setting that is selected 4 Press and hold the Pro
15. o Tach Learn Programming Page 7 9 Program Overview amp System Reset Program Menu 1 User Settings Program Menu 2 Additional Settings Program Menu 3 Starter Settings Program Menu 4 Tach Settings Operations Page 10 Single amp Dual Car Operation Timer Mode Manual Transmission Reservation Mode Additional Operations Page 11 1st amp Second Car Transmitter Programming i Emergency System Service Mode Battery Replacement Relay Diagrams Page 12 DIAGNOSTICS PARK LIGHTS STATUS LED DIAGNOSTIC CODE 3 Flashes Series of 3 Flashes Door Opened M Models 3 Slow Flashes LED s On Solid System Is In Service Mode 4 Slow Flashes Series of 4 Flashes Not in Reservation Mode M units 5 Flashes Series of 5 Flashes Hood Pin Opened 5 Slow Flashes Series of 5 Flashes Ignition On During Start Attempt 6 Flashes Series of 6 Flashes Brake Pedal Shutdown 7 Flashes Series of 7 Flashes Tach Lock Out 8 Flashes Series of 8 Flashes 3 Start Attempts with no start If the remote starter has a failed start attempt or if a safety input is activated the Diagnostic Memory will store up to four shutdowns in memory This information can then be accessed to determine the source of the shutdown To Enter Diagnostic Mode Step 1 Turn the ignition on wait two seconds then turn off Press the Program Button and release Step 2 The system will respond with three park light flashes and the horn will honk option
16. orking correctly The system s default programming will work on the majority of vehicles but might need to be adjusted for some applications If the installation requires special timing or additional features proceed to Program Mode ATTENTION Hood Pin MUST always be connected NOTE Always inform user to place system in Service Mode before any service work is performed on the vehicle Installation Guide 6 Pin Power Connector Yellow Starter 30amp output 12volts during crank only Green Heater 30amp output 12volts in accessory off during start Red 12 power 30amp input Constant 12volt power at ignition harness Red 12 power 30amp input Constant 12volt power at ignition harness Blue Ignition 1 30amp output 12volts in ignition and start positions White Select Out 30amp output Selectable Output See jumper diagram 11 Pin Connector n Yellow Re Arm 0 75sec Pulse With Lock And On Shutdown Red White 3rd CH Trunk Release Active When The Unlock Is Held For 3seconds Brown Disarm 0 75sec Pulse With Unlock And Before Start Orange Out While Running Negative While Locked Starter Program Mode White Blue Horn Horn Honk Output User Program Mode Black White Park Brake Negative Park Brake Input Manual Transmission Models Only Purple Door Positive Door Trigger Input Manual Transmission Models Only White Park Lights Positive Park light Output 10 Amp Max Green White Hood Pin Negative Hood Pin Input M
17. s to select setting 5 This will be confirmed by 5 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change selection Setting 6 Starter Kill Bypass Module Output Orange wire on 14 Pin Con en 1 Active Starter Kill 1 Flash On when locked Before ignition and 2 seconds after ignition turns off 2 Passive Starter Kill 2Flashes Same as setting 1 but will arm 60sec after the ignition turns off 3 Bypass Module 3Flashes Output before ignition Stays on 2 seconds after ignition turns off Setting 7 Safety Start Mode 1 Safety ON 1 Flash Must press the start button twice to remote start the vehicle 2 Safety OFF 2 Flashes Press the start button once to remote start the vehicle Press the Program Button 7 times to select setting 7 This will be confirmed by 7 LED flashes Press and hold the Program Button until you receive the appropriate of park light flashes and or horn honks Release the Program Button Press Program Button momentarily to move to next program step or repeat to change serif Q Installation Guide d B50 OPERATIONS PROGRAM MODE 4 TACH SETTINGS Setting 1 Auto Tach Learn 1 Make all the required wire connections and plug in the Unit The park lights should flash twice upon power up 2 Turn the Ignition Key ON Park Lights will turn on
18. sed must be programmed at the same time All transmitters not programmed at this time will be erased from memory for security The system holds a maximum of 4 transmitter codes including 2nd car remote codes You can program the same remote as a 1st car remote in one vehicle and as a 2nd car remote in a second vehicle System Service Mode ACTIVATING Service Mode 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash five times and the horn optional will honk five times to confirm Ignition that the system is in Service Mode On 2 While in Service Mode the remote start functions will be disabled and LED s will be 4 ON steady Door locks and trunk release are still operational m DEACTIVATING Service Mode 1 While the ignition is ON press and hold the Program Button for five seconds The park lights will flash two times and the horn optional will honk two times to confirm thatthe system has exited Service Mode 2 Remote start functions will return to normal operation System Service Mode By Remote ACTIVATE Service Mode 1 Press and Release button 4 then press and hold Button 4 again for 6 yi Q IP seconds until Status LED comes on Steady NOTE If horn is connected the horn will honk 5 times DEACTIVATE Service Mode 1 Press and Release button 4 then press and hold Button 4 again for 6 seconds until Status LED turn off NOTE If horn is conn
19. t flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 3 Horn Honk Timing _ 1 5ms Pulsed Output 1 Flash Short Quiet Pulses Oms Pulsed Output 2 Flashes Long Loud Pulses Oms Pulsed Output 3 Flashes Normal Medium Pulses Installation Guide Ss PROGRAM MODE 3 STARTER SETTINGS Setting 1 Special Door Lock Unlock 1 Type 1 1 Flash Unlock before start Lock pulse after start and shutdown 2 Type 2 2 Flashes Lock pulse only after remote starter shuts off r Normal Operation 3 Flashes No additional re lock pulses Press the Program Button 1 time to select setting 1 This will be confirmed by 1 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the Program Button Press momentarily to move to next program step or repeat to change selection Setting 2 Gas Diesel Mode Blue Wire on 14 Pin m 1 Positive Glow 30seconds 1 Flash Waits a maximum 30 seconds before starting 2 Timed Delay 15 Seconds 2 Flashes Ignition ON for 15 seconds before engaging remote starter 3 Gas Negative Glow Plug 3 Flashes Waits 2 seconds to start if no diesel input is detected Press the Program Button 2 time to select setting 2 This will be confirmed by 2 LED flash Press and hold the Program Button until you receive the appropriate of park light flashes and siren chirps Release the
20. te Park Brake Connect to park brake switch When brake is applied Note Manual Transmission units MUST be set into Reservation Mode to remote start See page 10 for details Step 2 Plug In The Module When all the connections are done the control module can be plugged in Before connecting the control module make sure the ignition is in the OFF position Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used Step 3 Auto Tach Learn 1 Make all the required wire connections and plug in the Unit The park lights should flash twice upon power up 2 Turn the Ignition Key ON Park Lights will turn on 3 Start the vehicle LED s on antenna will come when proper tach signal is detected then after 30 35 seconds the park lights will turn off then flash twice to confirm tach learning The system will flash the park lights seven times if not tach learned and the start button is pressed The system must be tach learned before remote starting If the LED s do not come on during tach learn a proper tach signal was not detected Note If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach source For best results connect the tach wire to the coil pack or to a fuel injector wire See Page 8 for tach adjustment New A system reset must be done before a new tach signal can be learned to the system Your Basic Install
21. the Button Exit Program Mode and remote start to test Setting 3 Adjust For Under Crank Step 1 Enter Program Mode Ignition ON OFF ON OFF ON then press the Program button on the antenna 1 time Step 2 Enter Program Mode 4 Press the on the remote Button 4 Step 3 Press the Program Button 3 times Led will start flashing 3 times Step 4 Press and Hold Program For 5 seconds until park lights flash each time lights flash the setting is increased Step 5 Release Program Exit Program Mode then remote start to test Reservation Mode Manual Transmissions Only Manual Transmission Remote Starters must have both the door trigger and park brake wires connected Most installs will require a clutch bypass This is a temporary bypass The clutch should only be bypassed during the activation of the remote starter Never disconnect or alter the switch to be always bypassed Always use a M Series Remote Starter on a manual transmission vehicle Never install a automatic Remote Starter model into a manual transmission vehicle It is not recommended to install a remote starter on a convertible type vehicle If doing so It is highly recommended that a radar sensor is installed to cover the proximity of the gear shift lever If the radar sensor is tripped the remote starter will exit Reservation Mode To enter Reservation Mode the following steps must be followed Step 1 While the vehicle is running place the
22. transmission in neutral and apply the parking brake Step 2 Press and release the brake pedal The park lights will flash Step 3 Turn the ignition key off and the vehicle will stay running Step 4 Exit the vehicle and close the door The vehicle will then shut off Step 5 The vehicle can now be safely remote started NOTE If the vehicle has a dome light delay the vehicle may stay running until the dome light turns off This is normally no longer than 30 seconds Reservation Mode will automatically be exited if the doors of the vehicle are opened The set up mode will then have to be repeated Reservation Mode Must Be set up each time the vehicle is parked Installation Guide Transmitter Programming Step 1 Within three seconds turn the ignition Key ON OFF ON OFF ON Leaving Key ON Step 2 Press and hold the Program Switch Parking Lights will come ON if park lights do not come on at this point turn key off for 5 seconds then repeat step 1 Step 3 Continue to hold the Program Switch the park lights go out Do not release Program Button Step 4 Press the LOCK button on each of 1st car remote s and press the button on each of the 2nd car remote s of the transmitters to be programmed The park lights will flash once and the horn will honk once each time a new code is learned Note Transmitter programming must done quickly Do not pause more than one second between each transmitter All the transmitters to be u
23. ult Setting For The System Is Second Ignition Output The jumpers control the output from the white wire at the 6 pin harness Place the jumper in the following positions to change the output Output on White wire Jumper position Second Starter Position 1 Second Accessory Position 2 Second Ignition Position 3 C5 Installation Guide BBO awicksTARTINs Step 1 Connect All Of the Following Wires 6 Pin Power Connector Yellow Starter Output Connect To The Vehicles Starter Wire Green Heater Output Connect To The Vehicles Accessory Wire Red 12 power Input Connect To Constant 12 Volt Power Source High Current Red 12 power Input Connect To Constant 12 Volt Power Source High Current Blue Ignition 1 Output Connect To the Vehicles Primary Ignition White Selectable Output Select Jumper Position If Necessary See Page 5 11 Pin Power Connector Black System Ground Connect To Chassis Ground White Park Lights Connect To Park Light System Green White Hood Pin Connect To The Hood Pin Safety Switch 4 Pin Power Connector Blue White Tach Connect To A CTach Source Above 2volts AC Pink Brake Switch Connect To When Brakes Is Applied Manual Transmissions Only Purple Door Pin Connect on vehicles with door pin systems Green Door Pin Connect on vehicles with door pin systems Black Whi
Download Pdf Manuals
Related Search