Home

AMX MVP-5100 Computer Monitor User Manual

1. Set the timeout value to 0 to disable Inactivity Page Flip mode Note The touch panel page used for the Inactivity page flip is named within a small Inactivity Page field below the buttons Panel Brightness Sets the display brightness levels of the panel e Press the Brightness Up Down buttons to adjust the brightness level Range 0 100 NOTE Be careful not to turn down the brightness too low to be able to see the Setup page Navigation Buttons The following Navigation buttons FIG 42 appear on the left side of the Setup page eer Press to access the Protected Setup pages etup Press to access the Project Information page in order to view information on the TPDesign file being used and Panel Information page in order to view Information Ale z panel specific information such as resolution and memory Press to access the Time page in order to alter the time and date settings on the Master A Time Press to access the Audio page in order to adjust audio parameters Audio on the panel Press to access the Battery page in order to monitor battery status in the panel FIG 42 Setup Page Navigation Buttons Protected Setup Pages Information on the Protected Setup pages is available on page 55 Information Button The Information button allows access of both the Project Information page which contains data on the TPDesign4 file being used with the MVP 5100 and the Pa
2. sssssssssssesssesssssssssssessseeesse 85 Step 2 Prepare Studio for communication via the USB port ssssssssssssssssssssssseeeeesesse 86 Step 3 Confirm and Upgrade the firmware via the USB port sccccceceeeeeeeeeeeees 88 A Special Note for Network Interface Connections c cscccceeseeeeeeeeeeseeseeeeeeeees 90 Uploading IR Codes to the MVP 5100 sssccccccsssssscssssssssssseesessessessssssssssneeeeees 93 Adding an existing IR file to NetLinx Studio cccsssesessessseeceeesssseccsscssseecessssseeees 95 Adding an AMX IR Database file to NetLinx Studio cssssccscssssecesessssecessssseeees 96 Adding a personal IR Database file to NetLinx Studio secccccceeeeeseeeeseseseeeeeee 98 Programming secesie reo E e EEEE a 99 OVOIVIEW sscinsccsaseisaseicnstose senses acoder sun eelsissancetensininnsssasuessiedeyeseactaianvopesenssbestinueessssbesswons 99 Page Commands cdisessstasnsctcticeseriesitcustessnsacecnessccetes suvennstosseseunceentesdeoussaseaeascaneseenanens 99 Programming Numba rsiecicccssi ccsccssccsanssonccceedccnszucesdssasacsooebedecseseseseucessobeocousssonsetess 105 RGB triplets and names for basic 88 colors sssseccscsssseeceseessseeccessesseeccessssseeeeoeens 105 Font styles and ID NUMbers sssc cscccsceccessesessecscseseconscececerosessseseeosssconsececesscessevsesevecostes 107 Border styles and Programming NUMbETS scccccccsessssssssssessssse
3. Support Cradle This retractable mechanism supports a resting MVP panel and allows a user to either insert or remove a connected MVP panel e Security Release pushbutton Located on the front of the unit this pushbutton toggles an on screen security keypad if security is enabled Entering the correct release code allows the MVP WCS 52 to release the touch panel from the security latch Operating Storage Environments Operating Temperature 0 C 32 F to 40 C 104 F Operating Humidity 20 85 RH Storage Temperature 20 C 4 F to 60 C 140 F Storage Humidity 5 85 RH Included Accessories MVP WCS 52 Wall Charging Station Quick Start Guide 93 5966 12 e Wallmount plastic back box 62 5966 12 e MVP WCS 52 Installation Kit Black KA 5966 01bl e MVP WCS 52 Installation Kit White KA 5966 01wh Other AMX Equipment e MVP TCS 52 Table Charging Station FG5966 1X e Wallmount Metal Rough In Box FG037 11 e MVP 5150 Modero Viewpoint Lite Touch Panel FG5966 07 MVP 5100 Modero Viewpoint IR Touch Panel FG5966 08 PS3 0 Power Supply FG423 30 The touch panel remains locked in the MVP WCS 52 until unlocked by the user This may be done by entering an appropriate password please refer to the Password Settings Page section on page 83 for more information or by pressing the Security Release button on the front of the device in emergencies The station ejects the
4. LPC Syntax Clear all LPC users from the Example User Access p N Passwords list on SEND_COMMAND Panel LPC the Password Clear all users from the User Access Password list on the Password Setup page Setup page Refer to the Other Settings section on page 82 for more information MVP Panel Lock Passcode Commands Cont ALPR Syntax Remove a given user from the User LPR lt user gt Variable Access Passwords list on user 1 50 ASCII characters the Password Example Setup page SEND_COMMAND Panel LPR Robert Remove user named Robert from the User Access Password list on the Password Setup page Refer to the Other Settings section on page 82 for more information ALPS This command allows you to Set the user name and password 1 Add a new user name and password OR 2 Set the password for a given user The user name and password combo is added to the User Access and or Password list in the Password Setup page The user name must be alphanumeric Syntax TLPS lt user gt lt passcode gt Variable user 1 50 ASCII characters passcode 1 50 ASCII characters Example SEND_COMMAND Panel LPS Manager undock Sets a new user name as Manager and the password to undock Example 2 SEND_COMMAND Panel LPS Manager test Changes the given user name password to test Refer to the Other Settings section on page 82 for more information Text
5. Disconnect any power source plugs or USB connections if necessary Protected Setup Navigation Buttons The Protected Setup Navigation Buttons FIG 51 appear on the left edge of the Protected Setup page The Navigation Buttons for the MVP 5100 have different functionality than those for the MVP 5150 as shown below System Settings Wireless Settings Calibrate G4 Web Control Other Settings Press to access the System Settings page which contains IP Settings and Master Connection information Press to access the Wireless Settings page which allows configuration of wireless connection settings Disabled in the MVP 5100 Press to access the Calibration page which allows proper calibration of the panel G4 Web Access is disabled Press to access the Passwords Setup page to specify firmware and user access passwords FIG 51 Protected Setup Navigation Buttons for the MVP 5100 a System Settings Settings Calibrate SEAN Control Settings Wireless OOS APA Press to access the System Settings page which contains IP Settings and Master Connection information Press to access the Wireless Settings page which allows configuration of wireless connection settings Disabled in the MVP 5100 Press to access the Calibration page which allows proper calibration of the panel Press to access the G4 Web Control page which enables and disables remote display and control of the panel via a
6. Fonts must be imported into a TPDesign4 project file The font ID numbers are assigned by TPDesign4 These values are also listed in the Generate Programmer s Report Border styles and Programming numbers Border styles can be used to program borders on buttons sliders and popup pages Border Styles and Programming Numbers No Border styles No Border styles 0 1 No border 10 11 Picture frame 2 Single line 12 Double line 3 Double line 20 Bevel S 4 Quad line 21 Bevel M 5 6 Circle 15 22 23 Circle 15 7 Single line 24 27 Neon inactive S 8 Double line 40 41 Diamond 55 9 Quad line The TPDesign4 Touch Panel Design program has pre set border styles that are user selectable The following number values cannot be used for programming purposes when changing border styles TPD4 border styles may ONLY be changed by using the name TPD4 Border Styles by Name No Border styles No Border styles 1 None 27 Cursor Bottom 2 AMX Elite L 28 Cursor Bottom with Hole 3 AMX Elite M 29 Cursor Top 4 AMX Elite S 30 Cursor Top with Hole 5 Bevel L 31 Cursor Left 6 Bevel M 32 Cursor Left with Hole 7 Bevel S 33 Cursor Right 8 Circle 15 34 Cursor Right with Hole 9 Circle 25 35 Custom Frame 10 Circle 35 36 Diamond 15 11 Circle 45 37 Diamond 25 12 Circle 55 38 Diamond 35 13 Circle 65 39 Diamond 45 14 Circle 75 40
7. Soft Drop Shadow 2 with outline Soft Drop Shadow 3 with outline Soft Drop Shadow 4 with outline Soft Drop Shadow 5 with outline Soft Drop Shadow 6 with outline Soft Drop Shadow 7 with outline Soft Drop Shadow 8 with outline Button Query Commands Button Query commands reply back with a custom event There will be one custom event for each button state combination Each query is assigned a unique custom event type The following example is for debug purposes only NetLinx Example CUSTOM_EVENT device Address Custom event type DEFINE_EVENT CUSTOM_EVENT TP 529 1001 CUSTOM EVENT TP 529 1002 CUSTOM EVENT TP 529 1003 CUSTOM_EVENT TP 529 1004 CUSTOM_EVENT TP 529 1005 CUSTOM_EVENT TP 529 1006 CUSTOM_EVENT TP 529 1007 CUSTOM_EVENT TP 529 1008 CUSTOM_EVENT TP 529 1009 CUSTOM_EVENT TP 529 1010 CUSTOM_EVENT TP 529 1011 CUSTOM_EVENT TP 529 1012 CUSTOM_EVENT TP 529 1013 CUSTOM_EVENT TP 529 1014 CUSTOM_EVENT TP 529 1015 Send_String Send_ String 0 Flag Send String 0 VALUE1 Send_ String Send String 0 VALUE3 Send_ String 0 0 0 0 VALUE2 0 0 TEXT 0 Send_String TEXT LENGTH ButtonGet Id ITOA CUSTOM ID Text Bitmap Icon Text Justification Bitmap Justification Icon Justification Font Text Effect Name Text Effect Color Word Wr
8. Variables sound name Name of the sound file Supported sound file formats are WAV amp MP3 Example SEND COMMAND Panel SOU Music wav Plays the Music wav file TKP Pops up the keypad icon and initializes the text string to that specified The Prompt Text is Present a optional telephone Syntax keypad TKP lt initial text gt lt prompt text gt Variables initial text 1 50 ASCII characters prompt text 1 50 ASCII characters Example SEND COMMAND Panel TKP 999 222 1211 Enter Phone Number Pops up the Keypad and initializes the text string 999 222 1211 with prompt text Enter Phone Number TPAGEON This command turns On page tracking whereby when the page or popups change a Turn On page string is sent to the Master This string may be captured with a CREATE_BUFFER tracking command for one panel and sent directly to another panel Syntax TPAGEON Example SEND COMMAND Panel TPAGEON Turns On page tracking TPAGEOFF Syntax Turn Off page TPAGEOFF tracking Example SEND COMMAND Panel TPAGEOFF Turns Off page tracking VKB Syntax Popup the VKB ad Example SEND COMMAND Panel VKB Pops up the virtual keyboard WAKE Syntax Force the panel WAKE out of screen Example saver mode SEND COMMAND Panel WAKE Forces the panel out of the screen saver mode Input Commands These Send Commands are case insensitive Input Commands
9. ACAL Put panel in calibration mode Syntax i CAL Example SEND COMMAND Panel CAL Puts the panel in calibration mode AKPS Set the keyboard passthru AVKS Send one or more virtual key strokes to the G4 application Syntax KPS lt pass data gt Variable pass data lt blank empty gt Disables the keyboard 0 Pass data to G4 application default This can be used with VPC or text areas 1 4 Not used 5 Sends out data to the Master Example SEND COMMAND Panel KPS 5 Sets the keyboard passthru to the Master Option 5 sends keystrokes directly to the Master via the Send Output String mechanism This process sends a virtual keystroke command VKS to the Master Example 2 SEND COMMAND Panel KPS 0 Disables the keyboard passthru to the Master The following point defines how the parameters within this command work Accepts keystrokes from any of these sources attached USB keyboard or Virtual keyboard Key presses and key releases are not distinguished except in the case of CTRL ALT and SHIFT Refer to theEmbedded Codes table on page 146 that define special characters which can be included with the string but may not be represented by the ASCII character set Syntax t4VKS lt string gt Variable string Only 1 string per command only one stroke per command Example SEND COMMAND Panel VKS 8 Sends out the keystroke backspace to the G4 a
10. BMF lt vt addr range gt lt button states range gt lt data gt parameters by Variables sending embedded codes variable text address char array 1 4000 and data button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state level range 1 600 level value is 1 65535 data B lt border style gt Set the border style name See the Border Styles and Programming Numbers table on page 108 B lt border 0 27 40 41 gt Set the borer style number See the Border Styles and Programming Numbers table on page 108 DO lt 1 5 gt lt 1 5 gt lt 1 5 gt lt 1 5 gt lt 1 5 gt Set the draw order Listed from bottom to top Refer to the BDO command on page 113 for more information F lt font 1 8 10 11 20 29 32 xx gt Set the font See the Default Font Styles and ID Numbers table on page 107 F lt font 01 08 10 11 20 29 32 xx gt Set the font See the Default Font Styles and ID Numbers table on page 107 Mi lt mask image gt Set the mask image Refer to the BMI command on page 118 for more information T lt text gt Set the text using ASCII characters empty is clear P lt bitmap gt Set the picture bitmap filename empty is clear l lt icon 01 9900 O clear gt Set the icon using values of 01 9900 icon numbers are assigned in the TPDesign4 Resource Manager tab Slots section l lt icon 0
11. EAP PEAP EAP FAST FIG 55 Wireless Security section Open Clear Text Settings Press the Open Clear Text button to open the Open Clear Text Settings page FIG 56 Ojan Sir eyes SAnja Cancel FIG 56 Wireless Settings page Open Clear Text Settings Open security does not utilize any encryption methodology but requires an SSID alpha numeric entry This entry must match the Network Name SSID entry of the target WAP so the panel knows what device it is using to communicate with the network Open Clear Text Settings SSID Service Set Identifier Opens an on screen keyboard to enter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in your wireless network e NXA WAP250Gs use AMX as their default SSID e If this field is left blank the panel will attempt to connect to the first available WAP Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to the Configuring Wireless Network Access MVP 5150 Only section on page 23 and the Using the Site Survey tool section on page 26 for further details on thes
12. WaGisecrmers suk 8 agra P Pan A Inactivity P Ea Banel Brightness lt nactivity Page ToT Ax QQ FIG 13 Setup page 2 Press the Protected Setup button This opens a keypad for entry of the password to allow access to the Protected Setup page FIG 14 Enter the device s password and press Done to proceed Ea Protected Setup Device ID Bepootsnhutdown Banel Name Options BUTO Undock FIG 14 Protected Setup page NOTE The default password for the Protected Setup page is 1988 but this may be changed at any time For more information on the Setup and Protected Setup pages refer to the Setup Pages section on page 45 and the Protected Setup Pages section on page 55 Setting the Panel s Device Number In the Protected Setup page 1 Press the Device Number field in the Device ID section to open the Device Number keypad 2 Enter a unique Device Number assignment for the device and press Done to return to the Protected Setup page The Device Number range is 1 32000 and the default is 0 3 Press Reboot to reboot the device and apply the new Device Number Wireless Settings Wireless Access Overview MVP 5150 Only DHCP When choosing DHCP a DHCP server must be accessible before the fields are populated Ifthe SSID Network Name and WEP fields have not previously been configured the Wireless Settings page will not work until the panel is rebooted The parameters of the wireless card mus
13. 1 4000 protected page flip flag value range 0 4 0 clears the flag Example SEND_COMMAND Panel BPP 500 1 Sets the button to protected page flip flag 1 sets it to password 1 A Button Commands Cont BRD Set the border of a button state states Only if the specified border is not the same as the current border The border names are available through the TPDesign4 border name drop down list Syntax BRD lt vt addr range gt lt button states range gt lt border name gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state border name Refer to the Border Styles and Programming Numbers table on page 108 Example SEND_COMMAND Panel BRD 500 504 amp 510 515 1 amp 2 Quad Line Sets the border by name Quad Line to those buttons with the variable text range of 500 504 amp 510 515 Refer to the TPD4 Border Styles by Name table on page 108 ABSF Set the focus to the text area Note Select one button at a time single variable text address Do not assign a variable text address range to set focus to multiple buttons Only one variable text address can be in focus at a time Syntax BSF lt vt addr range gt lt selection value gt Variable variable text address range 1 4000 selection value Unselect 0 and select 1 Example S
14. ML lt max length gt Set the maximum length of a text area MK lt input mask gt Set the input mask of a text area L lt 0 1 gt Log On Log Off the computer control connection N lt network name gt Set network connection name P lt password gt Set the network connection password Example SEND_COMMAND Panel BMF 500 1 B10 CFRed CB Blue sCTBlack Ptest png Sets the button OFF state as well as the Border Fill Color Border Color Text Color and Bitmap A Button Commands Cont ABMI Mask image is used to crop a borderless button to a non square shape This is typically Set the button used with a bitmap mask image Syntax BMI lt vt addr range gt lt button states range gt lt mask image gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state mask image Graphic file used Example SEND COMMAND Panel BMI 530 1 amp 2 newMac png Sets the button with variable text 530 ON OFF state mask image to newmac png ABML If this value is set to zero 0 the text area has no max length The maximum length avail Set the maximum length of the text area button able is 2000 This is only for a Text area input button and not for a Text area input masking button Syntax BML lt vt addr range gt lt max length gt Variable variable text addres
15. Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state color value Refer to the RGB Values for all 88 Basic Colors table on page 105 for more information Example SEND_COMMAND Panel BCF 500 504 amp 510 515 1 12 SEND_COMMAND Panel BCF 500 504 amp 510 515 1 Yellow SEND_COMMAND Panel BCF 500 504 amp 510 515 1 F4ECOA63 SEND_COMMAND Panel BCF 500 504 amp 510 515 1 F4ECOA Sets the Off state fill color by color number Colors can be set by Color Numbers Color name R G B alpha colors RRGGBBAA and R G amp B colors values RRGGBB A Button Commands Cont ABCT Set the text color to the specified color Only if the specified text color is not the same as the current color Note Color can be assigned by color name without spaces number or R G B value RRGGBB or RRGGBBAA Syntax BCT lt vt addr range gt lt button states range gt lt color value gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state color value Refer to the RGB Values for all 88 Basic Colors table on page 105 for more information Example SEND_COMMAND Panel BCT 500 504 amp 510 1 12 Sets the Off state border color to 12 Yellow Colors can be set by Col
16. s cccseccicccscessonsctescsveesessecesssnesesoesseccstesesses 21 Accessing the Setup and Protected Setup Pages cccccssssssssssssccceessesssessssssssseeeees 21 Setting the Panels Device NUMbE cscsscsssssseseececeeesesssessesessssseseeesesesssessessneees 22 Wireless Settings Wireless Access Overview MVP 5150 Only ssssccccsseseees 23 DHCP verrees erns sects steed AE tuueeetediste suey OEEO O 23 Configuring Wireless Network Access MVP 5150 Only scccccscsssssssssssssseeeeeees 23 Step 1 Configure the Device s Wireless IP Settings MVP 5150 Only 006 23 Wireless communication using a DHCP Address cccssessssssssessececcessesesessessssnseeeeees 24 Wireless communication using a Static IP Adress cccssessssssssccceeeesesessesesessseeees 25 Using the Site Survey tol is lt ssissscciccec cece evevssesentesuecceccctoetessusssoseueuecocesseseesttacessosessecececes 26 Step 2 Configure the Card s Wireless Security Settings scccccccsssssessssseeeeees 27 Configuring the device s wireless card for unsecured access to a WEP 20000 27 Se Automatically setting SSID ciiccsc sc0scccescccceetcessestsysesdesctctcateeecectsecetevessuteccoee cedeseseneessivsees 29 Manually setting SSID si csccscicccscecccesscesseebessdccceboccnvessesnes ses osbeuccoucncecesessosevevsucecouboceceeeess 29 Configuring multiple wireless touch panels to communicate
17. Displays the feedback blink rate in 10 second increments Job Comments Displays any comments associated to the job from the TPD4 project file Cradle Sensor Port Displays the port used by the charging cradle sensor Cradle Sensor Channel Displays the channel used to broadcast the charging cradle sensor status IR receivers and transmitters on G4 panels share the device address number of the panel NOTE Panel Information Page The Panel Information page provides detailed panel information FIG 44 Panel type Rinmnware Version Setup espe igh Port lit Address High Channel High Leye P Seti Mince E 0000000000000000 Setup Pages Version MVP 800x480 2 16 FIG 44 Panel Information page Panel Information Screen Width 800 Screen Height Screen Retest Rate Screen Rotation Power Up Page StartUp sting Wake Up Sting SIEP Sting File System 112 MB free of 192 MB RAM 60 MB free of 128 MB Pane Start timne Bulb ours Features on this page include Panel Information Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Panel Type Displays the model of the panel being used Firmware Version Displays the vers
18. Properties window FIG 31 4 Local Area Connection 3 Properties ia General Authentication Advanced Connect using B Linux USB Ethemet RNDIS Gadget L This connection uses the following items Boos Packet Scheduler 3 Network Monitor Driver Uninstall Description Transmission Control Protocol Intermet Protocol The default wide area network protocol that provides communication across diverse interconnected networks L Show icon in notification area when connected Notify me when this connection has limited or no connectivity FIG 31 Local Area Connection Properties 4 Inthe Local Area Connection Properties window FIG 31 under the General tab select Internet Protocol TCP IP and click on Properties to open the Internet Protocol TCP IP Properties window FIG 32 Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway a Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server FIG 32 Internet Protocol TCP IP Properties 5 In the new window Select
19. Zero Value1 Button state number Value2 Actual length of string Value3 Index Text Text from the button Text length Button text length Example SEND COMMAND Panel TXT 529 1 Gets the button OFF state text information The result sent to the Master would be ButtonGet Id 529 Type 1001 Flag 0 VALUE1 1 VALUE2 14 VALUE3 1 TEXT This is a test TEXT LENGTH 14 Sa E A Rii Panel Runtime Operations Serial Commands are used in the AxcessX Terminal Emulator mode These commands are case insensitive Panel Runtime Operation Commands ABEEP Output a single beep even if beep is Off Syntax ABEEP LESLI Example SEND COMMAND Panel ABEEP Outputs a beep of duration 1 beep even if beep is Off ADBEEP Output a double beep even if beep is Off Syntax RDBEEP Example SEND COMMAND Panel ADBEEP Outputs a double beep even if beep is Off AKB Pop up the keyboard icon and initialize the text string to that Keyboard string is set to null on power up and is stored until power is lost The Prompt Text is optional Syntax AKB lt initial text gt lt prompt text gt keyboard icon and initialize the text string to that specified Variables initial text 1 50 ASCII characters prompt text 1 50 ASCII characters Example SEND COMMAND Panel AKB Texas Enter State Pops up the Keyboard and initializes the text string Texas with
20. 75 Advanced Settings xi Adapters and Bindings Provider Order Connections are listed in the order in which they are accessed by network services Connections ade Local Area Connection 25 a AMX atk Local Area Connection be Remote Access connections ei Bindings for Local Area Connection 25 File and Printer Sharing for Microsoft Networks Fi Internet Protocol iru mi F z Mic Ne Intemet Protocol TE Cancel FIG 75 Advanced Settings window 4 Under the Adapters And Bindings tab the user needs to make sure the Local Area Connection is not at the top of the Connections list If it is at the top of the list FIG 75 select it and use the down arrow to the right of the list to move it to the bottom of the list FIG 76 Advanced Settings 29x Adapters and Bindings Provider Order Connections are listed in the order in which they are accessed by network services Connections k Local Area Connection Local Area Connection 25 b Remote Access connections eis Bindings for AMX m File and Printer Sharing for Microsoft Networks 9 Intemet Protocol TCP IP v E Client for Microsoft Networks Internet Protocol TCP IP FIG 76 Moving the Local Area Connection 5 In the lower Bindings for Local Area Connection field unselect ALL bindings by clicking on the checkboxes by each binding to r
21. 99 ABNT Syntax Set the TakeNote t BNT lt vt addr range gt lt network port gt network port for Variable the specified Addresses variable text address range 1 4000 network port 1 65535 Example SEND_COMMAND Panel BNT 973 5000 Sets the TakeNote button network port to 5000 BOP The button opacity can be specified as a decimal between 0 255 where zero 0 is Set the button invisible and 255 is opaque or as a HEX code as used in the color commands by opacity preceding the HEX code with the sign In this case 00 becomes invisible and FF becomes opaque If the opacity is set to zero 0 this does not make the button inactive only invisible Syntax BOP lt vt addr range gt lt button states range gt lt button opacity gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state button opacity 0 invisible 255 opaque Example SEND_COMMAND Panel BOP 500 504 amp 510 515 1 200 Example 2 SEND_COMMAND Panel BOP 500 504 amp 510 515 1 C8 Both examples set the opacity of the buttons with the variable text range of 500 504 and 510 515 to 200 A Button Commands Cont BOR Set a border toa specific border style associated with a border value for those buttons with a defined address range Refer to the Border Styles and Programming Numbers t
22. Empty Device Tree System entry and select Refresh System to re populate the list Configuring Communication 44 MVP 5100 5150 Modero Viewpoint Touch Panels Setup Pages Both the MVP 5100 and MVP 5150 feature on board Setup pages Use the options in the Setup pages to access panel information and make various configuration changes To access the Setup pages press the reset button and hold for 3 to 5 seconds FIG 40 Reset button Press and hold for 3 seconds to access the Setup pages FIG 40 Setup Page Access buttons Setup Pages The Setup page FIG 41 allows quick access to several essential panel properties oan 275 SE Sonnsetion Status Display Timeout Setup IT Information DPABIE TIMESITON External Power Attempting via Ethernet Inactivity Rage elie mime _ m Inactivity Page Baten Panel Brightness 4 FIG 41 MVP 5100 main Setup page Features on this page include Setup Page Navigation Buttons The buttons along on the left side of the page provide access to secondary Setup pages see following sections Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Setup Page Cont Connection Status Displays whether the panel has external communication as well as the encrypt
23. File Edit View Project Build Diagnostics Debug Tools Settings Window Help Oles 6n ga Tels eane A E 32001 NSX Application AMX Corp 2 3 5 10022 MVP 8400 AMX Corp v2 57 51 01D 2 Kernel AMX Corp 2 4 20 6 OID 3 Root File System AMX Corp OID 4 Bootrom AMX Corp None OID 5 Sensor AMX Corp v1 29 OlD 6 Opt File System AMX Corp 01D 7 Battery Base AMX Corp 2 J OID 8 Foga AMX Corp v7 00 1 Masters Devices Ports a ml w Description NX CV7 Nx CV10 MVP 7500 MYP 8 MYP split screen issue fixed Support for Nx CV10 Contents Firmware MIPS Bootloader for MVP 7500 MVP 8401 ersion v1 05 15 Target MIPS amp Workspace T Online Tree J K 2 Firmware Linux Kernel for MVP 7500 MVP 8400 N q gt f iz E m Target A Device Port 1 System 1 Comm Virtual NetLing Master Sys 1 M Reboot Device Sending file fpga tsk File 3 of 8 Please Wait 10022 4 4 gt Status Find In Files Find IR Files File Transfer Status Notifications 4 Ready FIG 8 9 10 11 12 13 14 15 Push Disabled Sort or __ Virtual NetLinx Master Sys ta 73 Using USB for a Virtual Master transfer OVR NUM 4 Select the panel s Kit file from the Files section Enter the Device value associated with the panel and th
24. IR Database to open the Select IR From A Database window The pane above the database directory tree will read AMX Directory Database 2 From the directory tree click on the AMX folder to open it Select the appropriate IR file and the Selected IR Information pane will display the available information on the file FIG 83 Ampro E sprit Gretag Selected IR Information AMX Manufacturer AMX amp Amplifier Category Interface amp Interface Model LANDMARK LANDMARK Hand Control PLRIR1 PLRIFA ersion 1 amp DOS File Name AMXO0001 1RL 2 amp Lighting Control Notes amp Media Management 10 28 97 MODE button does NOT send It switches among mod amp Switcher Audio Video Anthem Apex Arcam e FIG 83 Selected IR Information pane 3 To add this IR file to the download list click Add to List and the IR file will appear in the Selected IR List pane To remove an accidentally selected IR file highlight the file to be removed in the Selected IR List pane and click Remove From List FIG 84 When finished click OK Selected IF List Manufacturer Category Model Hand Control Version AMX Interface LANDMA PLRIRI 1 Add To List Remove From List FIG 84 Selected IR List pane 4 Inthe File Properties window FIG 85 verify the Identifier and Description information in the only two fields with editable data and click OK File Properties File Inform
25. Light Yellow 255 255 0 13 Light Yellow 223 223 0 14 Yellow 191 191 0 15 Medium Yellow 159 159 0 16 Dark Yellow 127 127 0 17 Very Dark Yellow 95 95 0 18 Very Light Lime 128 255 0 19 Light Lime 112 223 0 20 Lime 96 191 0 21 Medium Lime 80 159 0 22 Dark Lime 64 127 0 23 Very Dark Lime 48 95 0 24 Very Light Green 0 255 0 25 Light Green 0 223 0 26 Green 0 191 0 27 Medium Green 0 159 0 28 Dark Green 0 127 0 29 Very Dark Green 0 95 0 30 Very Light Mint 0 255 128 31 Light Mint 0 223 112 32 Mint 0 191 96 33 Medium Mint 0 159 80 34 Dark Mint 0 127 64 35 Very Dark Mint 0 95 48 ee RGB Values for all 88 Basic Colors Cont Index No Name Red Green Blue 36 Very Light Cyan 0 255 255 37 Light Cyan 0 223 223 38 Cyan 0 191 191 39 Medium Cyan 0 159 159 40 Dark Cyan 0 127 127 41 Very Dark Cyan 0 95 95 42 Very Light Aqua 0 128 255 43 Light Aqua 0 112 223 44 Aqua 0 96 191 45 Medium Aqua 0 80 159 46 Dark Aqua 0 64 127 47 Very Dark Aqua 0 48 95 48 Very Light Blue 0 0 255 49 Light Blue 0 0 223 50 Blue 0 0 191 51 Medium Blue 0 0 159 52 Dark Blue 0 0 127 53 Very Dark Blue 0 0 95 54 Very Light Purple 128 0 255 55 Light Purple 112 0 223 56 Purple 96 0 191 57 Medium Purple 80 0 159 58 Dark Purple 64 0 127 59 Very Dark Purple 48 0 95 60 Very Light Magenta 255 0 255 61 Light Magenta 223 0 223 62 Magenta 191
26. PC and the panel prior to installing the USB Driver will cause a failure in the USB driver installation WARNING Step 1 Configure the panel for a USB Connection Type 1 After completing the installation of the USB driver confirm the proper installation of the large Type A USB connector to the PC s USB port and restart your computer 2 After the panel powers up hold the reset button to display the Setup Page for more information refer to the Accessing the Setup and Protected Setup Pages section on page 21 and open the Protected Setup page 3 Press System Settings to open the System Settings page Toggle the blue Type field in the Master Connection section until the choice cycles to USB ALL fields are then grayed out and read only However they still display any previous network information NOTE 5 Press the Back button on the touch panel to return to the Protected Setup page Ake a 6 Press the Reboot button both to save any changes and to restart the panel Remember that the panel s connection type must be set to USB prior to rebooting the panel and prior to inserting the USB connector 7 ONLY AFTER the unit displays the first panel page should you THEN insert the mini USB connector into the Mini USB Port on the panel It may take a minute for the panel to detect the new connection and send a signal to the PC indicated by a green System Connection icon e Ifa few minutes have gone by and the System Connection ico
27. Panel BWW 500 1 1 Sets the word wrap on for the button s Off state A Button Commands Cont ACPF Clear all page flips from a button Syntax CPF lt vt addr range gt Variable variable text address range 1 4000 Example SEND_COMMAND Panel CPF 500 Clears all page flips from the button ADLD Set the disable cradle LED flag Syntax DLD lt status gt Variable status 0 cradle operates normally 1 forces the cradle LEDs to always be dim Example SEND_COMMAND Panel DLD 1 Disables the cradle LEDs ADPF Delete page flips from button if it already exists Syntax DFP lt vt addr range gt lt actions gt lt page name gt Variable variable text address range 1 4000 actions Stan dard Page Flip to standard page Prev ious Page Flip to previous page Show Popup Show Popup page Hide Popup Hide Popup page Togg le Popup Toggle popup state ClearG roup Clear popup page group from all pages ClearP age Clear all popup pages from a page with the specified page name ClearA Il Clear all popup pages from all pages page name 1 50 ASCII characters Example SEND COMMAND Panel DPF 409 Prev Deletes the assignment of a button from flipping to a previous page ENA Enable or disable buttons with a set variable text range Syntax It ENA lt vt addr range gt lt command value gt Variable variable text add
28. Press the EAP LEAP button to open the EAP LEAP Settings page FIG 60 EAP LEAP Identity Password Save Cancel FIG 60 Wireless Settings page EAP LEAP Settings EAP Extensible Authentication Protocol is an Enterprise authentication protocol that can be used in both wired and wireless network environments EAP requires the use of an 802 1x Authentication Server also known as a Radius server The configuration fields described below take variable length strings as inputs An on screen keyboard is opened when these fields are selected LEAP Lightweight Extensible Authentication Protocol was developed to transmit authentication information securely in a wireless network environment LEAP does not use client panel or server RADIUS certificates and is therefore one of the least secure EAP security methods However it can be utilized successfully by implementing sufficiently complex passwords EAP LEAP security is designed for wireless environments where having a client or server certificate validation scheme in place is not required yet necessary to transmit data securely over a wireless network EAP LEAP Settings SSID Service Set Identifier Opens an on screen keyboard to enter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensiti
29. Reinke into Primary Bs 192 168 20 7 Secondary DNS 192 168 20 9 SSID MAG Address 00 C0 1B 08 76 2E ete meetin On Ghannels Disabled k Link Gorality Access Point j ces CD EE mystique SE FIG 54 Wireless Settings page reads from and assigns values to the WAP Features on this page include Wireless Settings Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Protected Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master IP Settings Sets the IP communication values for the panel DHCP STATIC Sets the panel to either DHCP or Static communication modes DHCP a temporary IP Addresses is assigned to the panel by a DHCP server If DHCP is selected the other IP Settings fields are disabled see below e Static IP is a permanent IP Address assigned to the panel If Static IP is selected the other P Settings fields are enabled see below IP Address Enter the secondary IP address for this panel Subnet Mask Enter the subnetwork address for this panel Gateway Enter the gateway address for this panel Host Name Enter the host name for this panel Primary DNS Enter the address of the primary DNS server used by this panel for host name lookups eee Wireless Settings Page
30. SEND COMMAND Panel MDC virtual PC Sets the mouse double click for use with the virtual PC SHO Syntax Show or hide a button with a set variable text range SHO lt vt addr range gt lt command value gt Variable variable text address range 1 4000 command value 0 hide 1 show Example SEND_COMMAND Panel SHO 500 504 amp 510 515 0 Hides buttons with variable text address range 500 504 amp 510 515 A Button Commands Cont ATEC Set the text effect color for the specified addresses states to the specified color The Text Effect is specified by name and can be found in TPD4 You can also assign the color by name or RGB value RRGGBB or RRGGBBAA Syntax t TEC lt vt addr range gt lt button states range gt lt color value gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state color value Refer to the RGB Values for all 88 Basic Colors table on page 105 Example SEND_COMMAND Panel TEC 500 504 amp 510 515 1 amp 2 12 Sets the text effect color to Very Light Yellow on buttons with variable text 500 504 and 510 515 ATEF The Text Effect is specified by name and can be found in TPD4 Set the text effect Syntax t TEF lt vt addr range gt lt button states range gt lt text effect name gt Variable variable text address r
31. Security page a ce EAP FAST Settings Press the EAP FAST button to open the EAP FAST Settings dialog FIG 62 EAP FASi 55 Identity Anonymous Identity Password Automatic PAG Provisioning PAG File iscation FIG 62 Wireless Settings page EAP FAST Settings EAP FAST Flexible Authentication via Secure Tunneling security was designed for wireless environments where security and ease of setup are equally desirable EAP FAST uses a certificate file however it can be configured to download the certificate automatically the first time the panel attempts to authenticate itself Automatic certificate downloading is convenient but slightly less secure since its the certificate is transferred wirelessly and could theoretically be sniffed out EAP FAST Settings SSID Service Set Identifier Opens an on screen keyboard to enter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in the wireless network NXA WAP250Gs use AMX as their default SSID e With EAP security the SSID of the WAP must be entered If it is left blank the panel will try to connect to the first access point detected that supports EAP However a successful connec
32. Station FG5966 1X e MVP WCS 52 Wall Charging Station FG5966 1X e MVP BP 51S Standard Capacity Replacement Battery Pack Kit FG5966 25K e MVP BP 51H High Capacity Replacement Battery Pack Kit FG5966 24K e MVP STYLUS 52 Stylus Pack of 3 FG5966 30 xx e CC USB USB Programming Cable FG10 5965 e MVP HP USB 1 8 Adapter FG5966 23 This device complies with FCC Part 15 and Industry Canada RSS 210 subject to the following conditions 1 This device must not cause harmful interference and 2 This device must accept all interference including interference that interferes with the operation of this device MVP 5100 5 2 Modero ViewPoint IR Touch Panel The MVP 5100 differs from the MVP 5150 in that it does not have a built in wireless card or the capacity to install one and only communicates with other devices via IR Otherwise the two devices are identical MVP 5100 Specifications FG5966 08 Dimensions 4 3 4 x 7 9 16 x 13 16 120 7 mm x 191 8 mm x 20 3 mm Weight e 1 25 Ibs 0 57 kg Enclosure Matte black plastic Power Requirements Without Charging Panel with battery fully charged e Constant current draw 0 3 A 12 VDC e Startup current draw 0 4 A 12 VDC Power Requirements While Charging Panel while charging battery e Constant current draw 1 1 A 12 VDC Startup current draw 1 3 A 12 VDC Minimum Power Supply Required PS3 0 Power Supply FG423 3
33. Susceptible to Fixed Passwords MS CHAP and deployment dictionary d MS CHAPv2 attacks One time passwords authentication protocols tokens EAP FAST Certificates N A N A N A e Fixed Passwords One time passwords tokens EAP communication overview EAP Authentication goes a step beyond just encrypting data transfers but also requires that a set of credentials be validated before the client panel is allowed to connect to the rest of the network FIG 91 Below is a description of this process It is important to note that no user intervention is necessary during this process It proceeds automatically based on the configuration parameters entered into the panel 802 1x EAP Over Wireless Authentication Server Client Panel uthentication S Supplicant Authenticator RADIUS Server Wireless Access Point FIG 91 EAP security method in process The client panel establishes a wireless connection with the WAP specified by the SSID 2 The WAP opens up a tunnel between itself and the RADIUS server configured via the access point This tunnel means that packets can flow between the panel and the RADIUS server but nowhere else The network is protected until authentication of the client panel is complete and the ID of the client is verified 3 The WAP Authenticator sends an EAP Request Identity message to the panel as soon as the wireless connection becomes active 4 The p
34. Syntax BIM lt vt addr range gt lt input mask gt Variable variable text address range 1 4000 input mask Refer to the Text Area Input Masking table on page 152 for character types Example SEND_COMMAND Panel BIM 500 AAAAAAAAAA Sets the input mask to ten A characters that are required to either a letter or digit entry is required ABLN Set the number of lines removed equally from the top and bottom of a composite video signal The maximum number of lines to remove is 240 A value of 0 will display the incoming video signal unaffected This command is used to scale non 4x3 video images into non 4x3 video buttons Syntax BLN lt vt addr range gt lt button states range gt lt number of lines gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state number of lines 0 240 Example SEND_COMMAND Panel BLN 500 55 Equally removes 55 lines from the top and 55 lines from the bottom of the video button A Button Commands Cont BMC Button copy command Copy attributes of the source button to all the destination buttons Note that the source is a single button state Each state must be copied as a separate command The lt codes gt section represents what attributes will be copied All codes are 2 char pairs that can be separ
35. This button opens the EAP PEAP Settings page FIG 63 on page 74 EAP PEAP security is designed for wireless environments where it is neces sary to securely transmit data over a wireless network e Refer to the EAP PEAP Settings section on page 74 for further details e For information on uploading a certificate file refer to the AMX Certificate Upload Utility section on page 162 Wireless Settings Page Cont Wireless Security Cont EAP TTLS This button opens the EAP TTLS Settings page FIG 64 on page 76 EAP TTLS security is designed for wireless environments where having a Radius server directly validate the identity of the client panel is necessary before allowing it access to the network Refer to the EAP TTLS Settings section on page 76 for further details e For information on uploading a certificate file refer to the AMX Certificate Upload Utility section on page 162 EAP TLS This button opens the EAP TLS Settings page FIG 65 on page 78 EAP TLS security is designed for wireless environments where securely transmitting data over a wireless network by adding an additional level of security protocol is necessary via the use of a private key Refer to the EAP TLS Settings section on page 78 for further details For information on uploading a certificate file refer to the AMX Certificate Upload Utility section on page 162 EAP LEAP This button opens the EAP LEAP Setti
36. USB connection to communicate directly to the panel For more information on configuring the panel for USB connection please refer to the Step 1 Configure the panel for a USB Connection Type section on page 85 Before beginning 1 If using the mini USB connection verify the panel has been configured to communicate via USB within the System Settings page and that the USB driver has been properly configured If changing the Master Connection type reboot the device to save the change 2 In NetLinx Studio select Settings gt Master Communication Settings from the Main menu to open the Master Communication Settings dialog FIG 34 Master Communication Settings r Available System s Configuration Settings lt No Active System Default Settings gt System E lt Teminal Settings lt No Active System Default Settings gt Configuration Communication Settings OK Cancel FIG 34 Master Communications Settings dialog box 3 Click the Communications Settings button to open the Communications Settings dialog FIG 35 Communication Settings gt Platform Selection j Transport Connection Option NetLins Master TCPAP Edit Settings Axcess Master Serial ees Authentication Required Virtual NetLins Master FIG 35 Communications Settings dialog box 4 Click the NetLinx Master radio button in the Platform Selection section 5 Click the Virtual NetLinx Master radio butt
37. Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel BWW 529 1 Gets the button OFF state word wrap flag status information The result sent to the Master would be ButtonGet Id 529 Type 1010 Flag 0 VALUE1 1 VALUE2 1 VALUES 0 TEXT TEXT LENGTH 0 Button Query Commands Cont FON Syntax Get the current FON lt vt addr range gt lt button states range gt font index Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1007 Flag Zero Value1 Button state number Value2 Font index Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel FON 529 1 Gets the button OFF state font type index information The result sent to the Master would be ButtonGet Id 529 Type 1007 Flag 0 VALUE1 1 VALUE2 72 VALUE3 0 TEXT TEXT LENGTH 0 ICO Syntax Get the current 2TCO lt vt addr range gt lt button states range gt icon ges Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1003 Flag Zero Value1 Button state number Value2 Icon Index Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel ICO 529
38. Wireless IP Settings MVP 5150 Only The first step to a successful setup of the internal wireless card is to configure the ZP Settings section on the Wireless Settings page This section configures the communication parameters from the MVP panel to the web Wireless communication using a DHCP Address In the Protected Setup page 1 Select Wireless Settings Wireless communication is set within the ZP Settings section of this page FIG 15 Wireless Settings IB Settings Wireless Secunty oeo GEED TK THT praes me Gateway 192 168 213 2 HostName Pre RPE ET PEPR EAP LEAP Serie ONS P RENREN SSID BlueSockett MAG Address 00 0C 01 B0 8A 38 Active Roaming Channel 6n Ghannels Disabled TEn Access Point A Wireless Access Point Site Survey Button FIG 15 Wireless Settings page IP Settings section 2 Toggle the DHCP Static field from the IP Settings section until the choice cycles to DHCP This action causes all fields in the ZP Settings section other than Host Name to be greyed out DHCP will register the unique factory assigned MAC Address on the panel and once the communication setup process is complete assign IP Address Subnet Mask and Gateway values from the DHCP Server NOTE 3 Press the optional Host Name field to open the Host Name keyboard and enter the host name information 4 Press Done after assigning the alpha numeric string of the host name 5 The remaining greyed o
39. a risk of explosion if the battery is replaced with an incorrect type Be sure to dispose of used batteries in a correct manner Power Management Since the MVP 5100 and MVP 5150 are battery powered handheld devices power management is a necessary concern Under continuous use the charge on the integral Lithium Polymer battery can last for as long as four hours However to maximize usability and minimize the chances of the device becoming completely discharged at a critical moment the device should be kept in its charging cradle or wall station when not in use Each device operates on two distinct power modes e Awake This is the normal power mode of the panel during operation In this mode all necessary modules are powered up and their respective clocks are being driven appropriately The device remains online with the Netlinx Master and continues to appear in the online tree of Netlinx Studio e Processor Shutdown The system enters this mode after a user selectable amount of inactivity time has elapsed or if the battery level falls below10 percent of its full charge This is the absolute lowest mode of operation during which power to all peripherals and components is turned off It is not online with the NetLinx Master and will not appear in NetLinx Studio The system remains in this mode until either it is rebooted or the battery is completely shut down In the latter case the panel has to be placed in a Table Charging Station in ord
40. allocated to the RAM cache RAM Current Size The size of the current RAM cache contents RAM Hit Rate The number of times the RAM cache was referenced since the last cache clearing Items In Cache RAM The total number of cached images in the RAM cache Password Settings Page The options on the Password Settings page FIG 68 allow assignment of passwords required for users to access the Protected Setup page and to release the device from a MVP WCS 52 Charging Station Password Settings mPanel Password ehange USET ACCESS Password 1 1 hello 7 helo TT Password 2 Password 3 Password 4 Password 5 Enable protected FIG 68 Password Setup page Features on this page include Password Setup Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Protected Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master In Panel Password Accesses the alphanumeric values associated to particular password sets Change The PASSWORD 1 2 3 4 and 5 protected buttons open a keyboard to enter alphanumeric values associated to the selected password group Note Clearing Password 5 removes the need to enter a password before accessing the Protected Setup page User Access Lists all previous passw
41. bargraph slider name Joystick cursor name GC lt bargraph slider color gt Set the bargraph slider color Joystick cursor color Gl lt bargraph invert gt Set the bargraph invert noninvert or joystick coordinate 0 1 2 3 GIV section on page 124 more information GU lt bargraph ramp up gt Set the bargraph ramp up time in intervals of 1 10 second GD lt bargraph ramp down gt Set the bargraph ramp down time in 1 10 second GG lt bargraph drag increment gt Set the bargraph drag increment Refer to the GDI command on page 124 for more information l lt video ON OFF gt Set the Video either ON value 1 or OFF value 0 OT lt feedback type gt Set the Feedback Output Type to one of the following None Channel Invert ON Always ON Momentary or Blink SM Submit a text for text area button SF lt 1 or 0 gt Set the focus for text area button OP lt 0 255 gt Set the button opacity to either Invisible value 0 or Opaque value 255 OP lt 00 FF gt Set the button opacity to either Invisible value 00 or Opaque value FF UN lt Unicode text gt Set the Unicode text See the UNI section on page 130 for the text format LN lt 0 240 gt Set the lines of video being removed BLN section on page 114 for more information EF lt text effect name gt Set the text effect EC lt text effect color gt Set the text effect color
42. connection of the button ABVN Syntax SEND_COMMAND lt DEV gt BVN lt vt addr range gt lt remote host gt Variables variable text address range 1 4000 remote host 1 50 ASCII characters Example SEND_COMMAND Panel BVN 500 191 191 191 191 Sets the remote host to 191 191 191 191 for the specific computer control button ABVP Set the network password for the specified address Syntax BYyP lt vt addr range gt lt network password gt Variable variable text address range 1 4000 network password 1 50 ASCII characters Example SEND_COMMAND Panel BVP 500 PCLOCK Sets the password to PCLOCK for the specific PC control button ABVT Set the computer control network port for the specified address Syntax ByT lt vt addr range gt lt network port gt Variable variable text address range 1 4000 network port 1 65535 Example SEND_COMMAND Panel BVT 500 5000 Sets the network port to 5000 ABWW Set the button word wrap feature to those buttons with a defined address range By default word wrap is Off Syntax BWW lt vt addr range gt lt button states range gt lt word wrap gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state word wrap O0 Off and 1 On Default is Off Example SEND_COMMAND
43. device 8 Insert the five screws and replace the screw covers using the replacement screw covers included in the Battery Pack Kit 9 Restart the device to confirm that the new battery is functioning correctly Appendix A Text Formatting Text Formatting Codes for Bargraphs Joysticks Text formatting codes for bargraphs provide a mechanism to allow a portion of a bargraphs text to be dynamically provided information about the current status of the level multistate and traditional These codes are entered into the text field along with any other text The following is a code list used for bargraphs Bargraph Text Code Inputs Code Bargraph Multi State Bargraph P Display the current percentage of the Display the current percentage of the bargraph derived from the Adjusted bargraph derived from the Adjusted Level Value as it falls between the Level Value as it falls between the Range Values Range Values V Raw Level Value Raw Level Value L Range Low Value Range Low Value H Range High Value Range High Value S N A Current State A Adjusted Level Value Range Low Value Adjusted Level Value Range Low Value subtracted from the Raw Level Value subtracted from the Raw Level Value R Low Range subtracted from the High Low Range subtracted from the High Range Range Dollar sign Dollar sign By changing the text on a button via a VT command you can modify the codes on a button
44. device top first The MVP WCS 52 uses two neodymium rare earth magnets to keep the touch panel from falling out of its cradle when the device is angled forward Unlocking the touch panel Once placed within the Wall Charging Station the touch panel remains secured until the user unlocks it To release the touch panel from the Wall Charging Station 1 Press the Security Release button 2 A password keypad will pop up on the touch panel screen Enter a password in the password keypad and press Enter 3 Wait for the Wall Charging Station to pivot the touch panel away from the wall 4 The device will remain in the ejected position until the touch panel is removed Wait until the device s ejection door has completely withdrawn before re installing the touch panel Unique passwords may be entered for up to four unique users as well as the administrator For more information on setting passwords please refer to the Password Settings Page section on page 83 Recharging To recharge the touch panel 1 Slide the device into the Wall Charging Station cradle bottom first and make sure the device is fully seated in the Charging Station Press the top of the touch panel back until it clicks The touch panel is now locked into the Charging Station and the station will automatically charge the device s battery Please refer to the Battery Settings Page section on page 53 to check on the battery charge status To release the
45. distributor VIP or other AMX autho rized entity in good standing and have the right to enter into and be bound by the terms of this Agreement INTELLECTUAL PROPERTY The AMX Software is owned by AMX and is protected by United States copyright laws patent laws international treaty provisions and or state of Texas trade secret laws Licensee may make copies of the AMX Software solely for backup or archival purposes Licensee may not copy the written materials accompanying the AMX Software TERMINATION AMX RESERVES THE RIGHT IN ITS SOLE DISCRETION TO TERMINATE THIS LICENSE FOR ANY REA SON UPON WRITTEN NOTICE TO LICENSEE In the event that AMX terminates this License the Licensee shall return or destroy all originals and copies of the AMX Software to AMX and certify in writing that all originals and copies have been returned or destroyed PRE RELEASE CODE Portions of the AMX Software may from time to time as identified in the AMX Software include PRE RELEASE CODE and such code may not be at the level of performance compatibility and functionality of the GA code The PRE RELEASE CODE may not operate correctly and may be substantially modified prior to final release or certain features may not be generally released AMX is not obligated to make or support any PRE RELEASE CODE ALL PRE RELEASE CODE IS PROVIDED AS IS WITH NO WARRANTIES LIMITED WARRANTY AMX warrants that the AMX Software other than pre release code will perform s
46. gt Variables page flip password 1 50 ASCII characters Example SEND COMMAND Panel PWD Main Sets the page flip password to Main APWD Password level is required and must be 1 4 Set the page flip Syntax password pWD lt password level gt lt page flip password gt Variables password level 1 4 page flip password 1 50 ASCII characters Example SEND COMMAND Panel PWD 1 Main Sets the page flip password on Password Level 1 to Main AVOL Syntax Set the panel t vOL lt volume level gt volume Variable volume level 0 100 100 is maximum volume setting Example SEND COMMAND Panel VOL 50 Set the panel volume to 50 Programming 148 MVP 5100 5150 Modero Viewpoint Touch Panels Battery Life and Replacement 2 NOTE O WARNING Overview The battery powering the MVP 5100 and MVP 5150 is designed for upwards of 300 deep discharge rechargings Regular shallow rechargings will extensively increase expected battery life and the device should be stored in either the Table Charging Station or the Wall Charging Station when not in use to keep it at an optimum charge The battery has reached its effective end of life after it can no longer hold more than a 70 percent charge Unlike traditional Lithium lon batteries the Lithium Polymer battery in the MVP 5100 and MVP 5150 has a very small charge retention decline as it is discharged and recharged This device has
47. number for the touch panel Enter DPS Please specify the intended device Device Number m Port Number fi System Number fi Cancel FIG 80 Enter DPS window 6 Click OK to close the window The IR file will now appear in the Workspace pane 7 From the main menu select Tools gt Firmware Transfers gt Send To NetLinx Device to open the Send to NetLinx Device window FIG 81 Send to NetLinx Device Location C Program Files 4Mx Control Disc NetLinx Studio 2 ps Fies File Name DateTime Sizet r Progress Please select a file to send Kit Fie Transfer FIG 81 Send to NetLinx Device window 8 Select the file to be transferred and click Close when finished Adding an existing IR file to NetLinx Studio To add an existing IR file to NetLinx Studio 1 In the NetLinx Studio Workspace select Add Existing IR File to open the Add Existing IR File window FIG 82 Existing Recent Look in i MVP_5100 gt e EE My Recent Documents Desktop My Documents My Computer My Network File name fi Places Files of type iR Files irl irv X Cancel FIG 82 Add Existing IR File window 2 Select the file from the directory and click Open when finished Adding an AMX IR Database file to NetLinx Studio To add an IR file contained in AMX s IR Database 1 In the NetLinx Studio Workspace select Add From AMX
48. the Windows Update Web site with your permission i Can Windows connect to Windows Update to search for software Yes this time only C Yes now and every time connect a device No not this time Click Next to continue lt Back Next gt Cancel FIG 27 Found New Hardware Wizard dialogue box 5 Select Yes this time only and click on Next 6 Inthe new window Select Use the following IP Address Under IP address provide an IP address Ensure that it is in the same subnet as the IP address given to the usb0 interface on the MVP 5100 but make sure that it has a different node number The IP address cannot be the same as the panel s USB IP address Under Subnet mask set the suitable subnet mask Click OK 7 In the next box FIG 28 make sure to Select Search for the best driver in these locations Select Include this location in the search e Click on Browse Select the folder that contains the linux inf file Found New Hardware Wizard Please choose your search and installation options ee Y Search for the best driver in these locations Use the check boxes below to limit or expand the default search which includes local paths and removable media The best driver found will be installed J Search removable media floppy CD ROM JV Include this location in the search ie ocuments and Settings user Desktop x Browse C Don t search
49. time date modifications made on the panel Time Display fields e These fields display the time in three formats STANDARD STANDARD AM PM and 24 HOUR Date Display fields These fields display the calendar date information in several different formats Set Date Time Use the Up Down arrow buttons to adjust the Master s calendar date and time The blue icon indicates which field is currently selected Year range 2000 2199 Month range 1 12 e Day range 1 31 Hour 24 hour military e Minute range 0 59 Second range 0 59 Audio Settings Page The Audio Settings page allows adjustment of volume levels and panel sounds settings FIG 46 Audio Settings Derive panel Sounds a SE Button Hit Button Miss FIG 46 Audio Settings pages Features on these pages include Audio Settings Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Default Panel Sounds Activating the Button Hit button plays a default sound when you touch an active button Activating the Button Miss button plays a default sound when you touch a non active button or any area outside of the active button Battery Settings Pag
50. touch panel unlock the touch panel and wait for the Wall Charging Station to pivot the touch panel away from the wall Installing the MVP WCS 52 Since the Wall Charging Station is intended to be affixed to a wall or other permanent structure care must be taken to ensure its proper installation to prevent potential damage to any touch panel placed within Other than wall installation tools the only tool required for this installation is a 1 Phillips screwdriver NOTE Installing the plastic Back Box The plastic back box has two knockouts at the top of the box and four 4 lockdown wings attached to the box with Phillips head screws For ease of installation the interior of the box contains an UP arrow pointing to the knockouts The Metal Rough In Box does not have to be installed beforehand but it offers an extra level of support To install the Plastic Back Box 1 Cut a hole into the wall or surface intended to hold the box The outer lip of the back box is sized 8 69 inches 220 66mm long and 6 0 inches 152 4mm high so the hole should be at least 1 4 6 4mm smaller in each dimension FIG 7 8 25 209 55mm ji 4 5 56 5 56 141 29mm 141 29mm t 8 25 209 55mm FIG 7 Recommended cutout for plastic back box A Make sure to measure the size of the intended hole before starting to cut it WARNING 2 Select the knockout to be removed from the top of the b
51. web enabled PC running a VNC client Press to access the Passwords Setup page to specify firmware and user access passwords Press to access the Tools page for panel connection logs panel statistics and the Connection Utility FIG 52 Protected Setup Navigation Buttons for the MVP 5150 System Settings Page The System Settings page FIG 53 displays sets the NetLinx Master s communication settings System Settings USBIE Settings Type mode Master Pon Nomber Deemame NDP Name Device 18002 FIG 53 System Settings page The elements of this page include System Settings Page Elements Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Protected Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master IP Settings Switches the IP settings between DHCP and Static DHCP means that the IP address and the subnet mask fields are greyed out in Static press either of the fields to open the P Address and Subnet Mask keypads Master Connection Sets the NetLinx Master communication values Type Sets the NetLinx Master to communicate with the panel via Ethernet or USB This is based on the cable connection from the rear Ethernet is a CAT 5 cable 10 100Base T terminated in an RJ 45 connector used to network computer
52. which was 01 02 03 04 05 the panel s key 4 must be set to 01 02 03 04 05 6 Toggle the Default Key field to choose a WEP Key value from 1 4 that matches what will be used on the target This value MUST MATCH on both devices These WEP Key identifier values must match for both devices 7 Press the particular WEP Keys button to launch the WEP Passphrase keyboard 8 Within the WEP Passphrase keyboard FIG 23 enter a character string or word such as AMXPanel and press Done when finished WEP Passphrase AMXPanel_ FIG 23 WEP Passphrase Keyboard e For example enter the word AMXPanel using a 128 bit hex digit encryption After pressing Done the on screen Current Key field displays a long string of characters separated by colons which represents the encryption key equivalent to the word AMXPanel e This series of hex digits 26 hex digits for a 128 bit encryption key should be entered as the Current Key into both the WAP and onto other communicating Modero panels by using the WEP Key dialog FIG 24 WEP Key 1 3e 22 fb 22 9b 38 22 c8 22 60 22 5b fa_ OPP PERORPP ES 2 EP AEE Ww e pi a Delete gt Emer Tome 7 Sir End ave Done FIG 24 WEP Key Keyboard 9 Write down this Current Key string value for later entry into the WAP s WEP Key field typically entered without colons and into other communicating panel s Current Key field 10 If entering a Current Key generated either by the ta
53. 0 both 120 VAC and 240 VAC models are shipped with this power supply Power Modes Certifications Battery Duration Memory AWAKE All necessary modules are powered up and device remains online with the Netlinx Master e ASLEEP Only the backlight will be turned off after the user selectable time of inactivity has elapsed Panel resumes the Awake Mode in 1 second PROCESSOR SHUTDOWN Power to all peripherals and components is turned off The system remains in this mode until it is rebooted e IEC60950 RoHS TELEC e Lithium polymer microbattery UN IATA e Four days of normal use 25 Awake state 25 standby and 50 Processor Shutdown e Three hours of continuous use continuous Awake state 128 MB Mobile DDRAM upgrade not available e 256 MB NAND Flash upgrade not available Panel LCD Parameters e Size 5 2 13 21 cm Type WVGA e Aspect ratio 16 x 9 Brightness luminance 300 cd m e Channel transparency 8 bit Alpha blending Contrast ratio 20 1 e Display colors 262 144 colors 18 bit color depth e Dot pixel pitch 0 23 mm e Panel type TFT Color Active Matrix Screen resolution 800 x 480 pixels HV 60 Hz frame frequency e Viewing angles Vertical 40 up from center and 80 down from center Horizontal 60 left from center and 60 right from center External Components Connector 5 pin Mini USB connector used for programm
54. 0 191 63 Medium Magenta 159 0 159 64 Dark Magenta 127 0 127 65 Very Dark Magenta 95 0 95 66 Very Light Pink 255 0 128 67 Light Pink 223 0 112 68 Pink 191 0 96 69 Medium Pink 159 0 80 70 Dark Pink 127 0 64 71 Very Dark Pink 95 0 48 72 White 255 255 255 73 Grey1 238 238 238 74 Grey3 204 204 204 75 Grey5 170 170 170 76 Grey7 136 136 136 77 Grey9 102 102 102 78 Grey4 187 187 187 79 Grey6 153 153 153 CON cml RGB Values for all 88 Basic Colors Cont Index No Name Red Green Blue 80 Grey8 119 119 119 81 Grey10 85 85 85 82 Grey12 51 51 51 83 Grey13 34 34 34 84 Grey2 221 221 221 85 Grey11 68 68 68 86 Grey14 17 17 17 87 Black 0 0 0 255 TRANSPARENT 99 53 99 Font styles and ID numbers Font styles can be used to program the text fonts on buttons sliders and pages The following chart shows the default font type and their respective ID numbers generated by TPDesign4 Default Font Styles and ID Numbers Font ID Font type Size Font ID Font type Size 1 Courier New 9 19 Arial 9 2 Courier New 12 20 Arial 10 3 Courier New 18 21 Arial 12 4 Courier New 26 22 Arial 14 5 Courier New 32 23 Arial 16 6 Courier New 18 24 Arial 18 7 Courier New 26 25 Arial 20 8 Courier New 34 26 Arial 24 9 AMX Bold 14 27 Arial 36 10 AMX Bold 20 28 Arial Bold 10 11 AMX Bold 36 29 Arial Bold 8 32 Variable Fonts start at 32
55. 1 9900 0 clear gt Set the icon using values of 01 9900 icon numbers are assigned in the TPDesign4 Resource Manager tab Slots section J lt alignment of text 1 9 gt As shown the following telephone keypad alignment chart Zero can be used for an absolute position JT lt alignment of text 0 9 gt As shown the above telephone keypad alignment chart BUT the 0 zero is absolute and followed by lt left gt lt top gt JB lt alignment of bitmap picture 0 9 gt As shown the above telephone keypad alignment chart BUT the 0 zero is absolute and followed by lt left gt lt top gt J lt alignment of icon 0 9 gt As shown the above telephone keypad alignment chart BUT the 0 zero is absolute and followed by lt left gt lt top gt A Button Commands Cont ABMF Cont For some of these commands and values refer to the RGB Values for all 88 Basic Colors table on page 105 CF lt on fill color gt Set Fill Color CB lt on border color gt Set Border Color CT lt on text color gt Set Text Color SW lt 1 or 0 gt Show hide a button SO lt sound gt Set the button sound EN lt 1 or 0 gt Enable disable a button WW lt 1 or 0 gt Word wrap ON OFF GH lt bargraph hi gt Set the bargraph upper limit GL lt bargraph low gt Set the bargraph lower limit GN lt bargraph slider name gt Set the
56. 1 amp 2 Gets the button OFF state icon index information The result sent to the Master would be ButtonGet Id 529 Type 1003 Flag 0 VALUE1 2 VALUE2 12 VALUES 0 TEXT TEXT LENGTH 0 Button Query Commands Cont 2JSB Syntax Get the current 2JSB lt vt addr range gt lt button states range gt bitmap Variable justification variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1005 Flag Zero Value1 Button state number Value2 1 9 justify Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel JSB 529 1 Gets the button OFF state bitmap justification information The result sent to the Master would be ButtonGet Id 529 Type 1005 Flag 0 VALUE1 1 VALUE2 5 VALUE3 0 TEXT TEXT LENGTH 0 2JSI Syntax Get the current 2gSI lt vt addr range gt lt button states range gt igon PERE Variable justification variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1006 Flag Zero Value1 Button state number Value2 1 9 justify Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel JSI 529 1 Gets the button OFF state icon justification
57. 78 R Workspace MVP 5100 1 Project s 5 6 M P 5100 a M YP 5100 Virtual NetLins Master lt 12 0 0 1 gt Source MVP 5100 G Include Module User Interface IR Other C Workspace TE OnLine Tree FIG 78 NetLinx Studio Workspace Tree 3 Right click on the JR folder and select the method to add the necessary IR files Add Existing IR File chooses from a previously downloaded IR file please refer to the Adding an existing IR file to NetLinx Studio section on page 95 for specific procedures Add From AMX IR Database chooses from AMX s IR file database please refer to the Adding an AMX IR Database file to NetLinx Studio section on page 96 for specific procedures Add From User IR Database chooses from a personal IR file database please refer to the Adding a personal IR Database file to NetLinx Studio section on page 98 for specific procedures 4 When the IR file appears in the Workspace Tree right click on the file and select Device Mapping to open the Device Mapping window FIG 79 E Device Mapping amp MvP 5100 Device Address amp MVP 5100 lt Custo User Source G User Interface amp IR AMX IRN AMX PLRIR1 1 Press the Map button to specify the device port system address FIG 79 Device Mapping window 5 Click the Map button to open the Enter DPS window FIG 80 and enter the device number port number and system
58. Application AMX Corp 2 10 10025 MYP 7500 AMX Corp v2 28 12 Shows Netlinx Studio version number Masters Devices Ports im 3m o Display Ww Gi werkenae We onire Tre Shows the current MVP E panel firmware version i ala Pii Status lt Findin Fies FindiR Fies File Transfer Status Notifiq and device number Ready Ron Aon Push Disabled E FIG 72 NetLinx Workspace window showing panel connection via a Virtual NetLinx Master The panel specific firmware is shown on the right of the listed panel Download the latest firmware file from www amx com and then save the Kit file to your computer Note that each kit file is intended for download to its corresponding panel 5 Ifthe panel firmware version is not the latest available locate the latest firmware file from the www amx com gt Tech Center gt Firmware Files gt Modero Panels section of the website 6 Click on the desired Kit file link and after accepting the Licensing Agreement verify download of the Modero Kit file to a known location NOTE Select Tools gt Firmware Transfers gt Send to NetLinx Device from the main menu to open the Send to NetLinx Device dialog B in FIG 73 Verify that the panel s System and Device number values match those values listed within the System folder in the OnLine Tree tab of the Workspace IN window A in FIG 73 NetLinx Studio
59. Authentication ssccesecssctisectesscstencscnsssius cstecciiatcctvnnecssnabesiebeceseactyedessstesvecsbsossbied 160 EAP Characteristics vciicecsccccxcves cctecseeedes sctbevesstessteseversiucettstensescusedeccscediseedbesudeagsSoceyeevixes 160 EAP communication overview ccccessesscccccceseesseececcessssseeeeeeeesesseseeeseeeeseeseeeeesoosoeees 161 AMX Certificate Upload Utility s ccicccccccsssessscoscssessctesscsozsesosscesuces cussecenssenoseseosonseees 162 How to Upload a Certificate File scccsicctsicsccsiccctuscutacececcstinndusczanlacbestetieeworneaeeentex 162 Appendix C Troubleshootihg sis asscssnstcsvapaccsdecdasvavsdsndenanisnnseaswedaneasheseunnaanwanas 164 Panel Doesn t Respond To Touche sssssscccccscessssccssssssssssesecessssssscssensssseeeseaeceees 164 Battery Will Not Hold Or Take A Charge ccccscscscssssssssssssesccesessssssssssssssseesseeeenes 164 Device Isn t Appearing In The Online Tree Tab cccssssssssscceeesessssecessssnseseseaeeenes 165 Device Can t Obtain a DHCP Address csssccccccssssscccesssssssssssscecesessssscesessnsssseseesees 165 My WEP Doesn t Seem To Be Working sccccccccsssccsssssssssssssscccesessssscessssnseeesseeseess 165 NetLinx Studio Only Detects One Of My Connected MasterS ssccccccsssseereessseee 165 Can t Connect To a NetLinx Master cccccccccsscsssssssssscesessscesesseeesceseeeeseeeseeeeeseseeeees 165 Only One Modero Panel In My Syste
60. Be Working WEP will not work unless the same default key is set on both the panel and the Wireless Access Point WAP For example if the access point was set to default WEP key 4 which was 01 02 03 04 05 the Modero s Default WEP key 4 must be set to 01 02 03 04 05 NetLinx Studio Only Detects One Of My Connected Masters Each Master is given a Device Address of 00000 Only one Master can be assigned to a particular System number If you want to work with multiple Masters open different instances of NetLinx Studio and assign each Master its own System value Example A site has an NXC ME260 64 and an NI 4000 In order to work with both units The ME260 can be assigned System 1 and the NI 4000 can then be assigned System 2 using two open sessions of NetLinx Studio v 2 x Can t Connect To a NetLinx Master Symptom I can t seem to connect to a NetLinx Master using NetLinx Studio 2 Select Settings gt Master Comm Settings gt Communication Settings gt Settings for TCP IP and uncheck the Automatically Ping the Master Controller to ensure availability The pinging is to determine if the Master is available and to reply with a connection failure instantly if it is not Without using the ping feature a connection may still be attempted but a failure will take longer to be recognized If you are trying to connect to a Master controller that is behind a firewall you may have to uncheck this option Most firewalls will not
61. COMMAND Panel GDI 7 128 Sets the bargraph with variable text 7 to a drag increment of 128 AGIV Parameters 1 2 and 3 will cause a bargraph or slider to be inverted regardless of Invert the joystick orientation Their effect will be as described for joysticks Syntax t GIv lt vt addr range gt lt joystick axis to invert gt Variable variable text address range 1 4000 joystick axis to invert 0 3 0 Normal 1 Invert horizontal axis 2 Invert vertical axis 3 Invert both axis locations For a bargraph 1 Invert 0 Non Invert Example SEND_COMMAND Panel GIV 500 3 Inverts the joystick axis origin to the bottom right corner A Button Commands Cont SGLH Change the bargraph upper limit Syntax GLH lt vt addr range gt lt bargraph hi gt Variable variable text address range 1 4000 bargraph limit range 1 65535 bargraph upper limit range Example SEND_COMMAND Panel GLH 500 1000 Changes the bargraph upper limit to 1000 AGLL Change the bargraph lower limit Syntax GLL lt vt addr range gt lt bargraph low gt Variable variable text address range 1 4000 bargraph limit range 1 65535 bargraph lower limit range Example SEND_COMMAND Panel GLL 500 150 Changes the bargraph lower limit to 150 GRD Change the bargraph ramp down time in 1 10th of a Syntax GRD lt vt addr range gt lt bargraph ramp d
62. Cont IP Settings Cont Secondary DNS Enter the secondary DNS address for this panel Domain Enter a unique name to the panel for DNS look up MAC Address This unique address identifies the wireless Ethernet card in the panel read only Active Roaming on When enabled connection allows active roaming between WAPs by switching Channels 1 6 and 11 between channels 1 6 and 11 if the other channel is unavailable Access Point MAC This unique address identifies the Wireless Access Point WAP used by this Address panel for wireless communication read only Site Survey button Launches the Wireless Site Survey page The options on this page allow you to detect sniff out all WAPs transmitting within range of the panel s Wi Fi card Data displayed on the Site Survey page is categorized by Network Name SSID WAP names Channel RF channels currently being used by the WAP Security Type security protocol enabled on the WAP if detectable Signal Strength None Poor Fair Good Very Good and Excellent MAC Address Unique identification of the transmitting Access Point Refer to the Using the Site Survey tool section on page 26 for more detailed information on the S te Survey page When communicating with a NXA WAP250G enter the MAC Address BSSID of the target WAP as the Access Point MAC Address Refer to the WAP250G Instruction Manual for more information Wireless Security Sets the wi
63. D used by the target WAP If this field is left blank the unit will attempt to connect to the first available WAP By default all WAP250Gs use AMX as their assigned SSID value One of the most common problems associated with connection to a WAP involves an incorrect SSID Make sure to maintain the same case when entering the SSID information ABC is not the same as Abc nn LN en NOTE Click Done when complete From the Open Clear Text Settings page FIG 19 press the Save button to incorporate the new information into the device and begin the communication process Verify the proper configuration in the fields in the JP Settings section Refer to Step 1 Configure the Device s Wireless IP Settings MVP 5150 Only section on page 23 for detailed information Press the Back button to return to the Protected Setup page and press the on screen Reboot button to save any changes and restart the device Remember that the connection must be configured to a target Master from the System Settings page 10 After the panel restarts return to the Wireless Settings page s RF Link Info section and verify the link quality and signal strength e The descriptions are None Poor Fair Good Very Good and Excellent FIG 17 The signal strength field should provide some descriptive text regarding the strength of the connection to a Wireless Access Point If no signal or no IP Address is displayed configuration of the network could
64. Diamond 55 15 Circle 85 41 Diamond 65 16 Circle 95 42 Diamond 75 17 Circle 105 43 Diamond 85 18 Circle 115 44 Diamond 95 19 Circle 125 45 Diamond 105 20 Circle 135 46 Diamond 115 21 Circle 145 47 Diamond 125 22 Circle 155 48 Diamond 135 23 Circle 165 49 Diamond 145 24 Circle 175 50 Diamond 155 25 Circle 185 51 Diamond 165 26 Circle 195 52 Diamond 175 CON cml TPD4 Border Styles by Name Cont er No Border styles No Border styles 53 Diamond 185 97 Menu Bottom Rounded 185 54 Diamond 195 98 Menu Bottom Rounded 195 55 Double Bevel L 99 Menu Top Rounded 15 56 Double Bevel M 100 Menu Top Rounded 25 57 Double Bevel S 101 Menu Top Rounded 35 58 Double Line 102 Menu Top Rounded 45 59 Fuzzy 103 Menu Top Rounded 55 60 Glow L 104 Menu Top Rounded 65 61 Glow S 105 Menu Top Rounded 75 62 Help Down 106 Menu Top Rounded 85 63 Neon Active L 107 Menu Top Rounded 95 64 Neon Active S 108 Menu Top Rounded 105 65 Neon Inactive L 109 Menu Top Rounded 115 66 Neon Inactive S 110 Menu Top Rounded 125 67 Oval H 60x30 111 Menu Top Rounded 135 68 Oval H 100x50 112 Menu Top Rounded 145 69 Oval H 150x75 113 Menu Top Rounded 155 70 Oval H 200x100 114 Menu Top Rounded 165 71 Oval V 30x60 115 Menu Top Rounded 175 72 Oval V 50x100 116 Menu Top Rounded 185 73 Oval V 75x150 117 Menu Top Rounded 195 74
65. END_COMMAND Panel BSF 500 1 Sets the focus to the text area of the button ABSM Submit text for text area buttons This command causes the text areas to send their text as strings to the NetLinx Master Syntax BSM lt vt addr range gt Variable variable text address range 1 4000 Example SEND_COMMAND Panel BSM 500 Submits the text of the text area button ABSO Set the sound played when a button is pressed If the sound name is blank the sound is then cleared If the sound name is not matched the button sound is not changed Syntax t BSO lt vt addr range gt lt button states range gt lt sound name gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state sound name blank sound cleared not matched button sound not changed Example SEND COMMAND Panel BSO 500 1 amp 2 music wav Assigns the sound music wav to the button Off On states A Button Commands Cont Set the computer control remote host for the specified address ABVL Syntax Log On Log Off t BVL lt vt addr range gt lt connection gt the computer Variable control ae connection variable text address range 1 4000 connection 0 Log Off connection and 1 Log On connection Example SEND_COMMAND Panel BVL 500 0 Logs off the computer control
66. Effects Names The following is a listing of text effects names associated with the TEF command on page 129 Text Effects Glow S Medium Drop Shadow 1 e Hard Drop Shadow 1 e Glow M Medium Drop Shadow 2 e Hard Drop Shadow 2 e Glow L Medium Drop Shadow 3 e Hard Drop Shadow 3 Glow X Medium Drop Shadow 4 e Hard Drop Shadow 4 Outline S Medium Drop Shadow 5 e Hard Drop Shadow 5 Outline M Medium Drop Shadow 6 e Hard Drop Shadow 6 Outline L Medium Drop Shadow 7 e Hard Drop Shadow 7 Outline X Medium Drop Shadow 8 e Hard Drop Shadow 8 Soft Drop Shadow 1 Medium Drop Shadow 1 with outline e Hard Drop Shadow 1 with outline Soft Drop Shadow 2 Medium Drop Shadow 2 with outline e Hard Drop Shadow 2 with outline Soft Drop Shadow 3 Medium Drop Shadow 3 with outline Hard Drop Shadow 3 with outline Soft Drop Shadow 4 Medium Drop Shadow 4 with outline Hard Drop Shadow 4 with outline Soft Drop Shadow 5 Medium Drop Shadow 5 with outline Hard Drop Shadow 5 with outline Soft Drop Shadow 6 Medium Drop Shadow 6 with outline e Hard Drop Shadow 6 with outline Soft Drop Shadow 7 Medium Drop Shadow 7 with outline e Hard Drop Shadow 7 with outline Soft Drop Shadow 8 Medium Drop Shadow 8 with outline Hard Drop Shadow 8 with outline ec Text Effects Cont Soft Drop Shadow 1 with outline
67. KNOWN security protocol enabled on the WAP e Signal Strength displaying None Poor Fair Good Very Good and Excellent e MAC Address Unique identification of the transmitting Access Point Wireless Site Survey Wireless New ones Network Name SSID Channel Security Signal MAC Address gt Eanna Connect FIG 16 Site Survey page To access the Site Survey Tool 1 From the Protected Setup page press the Wireless Settings button to open the Wireless Settings page 2 Press the Site Survey button This action launches the Wireless Site Survey page which displays a listing of all detected WAPs in the communication range of the internal card e The card scans its environment every four seconds and adds any new WAPs found to the list Every scan cycle updates the signal strength fields e Access points are tracked by MAC Address e If the WAP s SSID is set as a blank then N A is displayed within the SSID field e If the WAP s SSID is not broadcast it will not show up on the Wireless Networks screen e Ifa WAP is displayed in the list is not detected for 10 scans in a row it is then removed from the screen In this way a user can walk around a building and track access points as they move in and out of range 3 Sort the information provided on this page by pressing on a column name This moves the sorting arrow to that column where it may be toggled up or down e Up arrow indicates that the infor
68. Oval V 100x200 118 Menu Right Rounded 15 75 Picture Frame 119 Menu Right Rounded 25 76 Quad Line 120 Menu Right Rounded 35 77 Single Line 121 Menu Right Rounded 45 78 Windows Style Popup 122 Menu Right Rounded 55 79 Windows Style Popup Status Bar 123 Menu Right Rounded 65 80 Menu Bottom Rounded 15 124 Menu Right Rounded 75 81 Menu Bottom Rounded 25 125 Menu Right Rounded 85 82 Menu Bottom Rounded 35 126 Menu Right Rounded 95 83 Menu Bottom Rounded 45 127 Menu Right Rounded 105 84 Menu Bottom Rounded 55 128 Menu Right Rounded 115 85 Menu Bottom Rounded 65 129 Menu Right Rounded 125 86 Menu Bottom Rounded 75 130 Menu Right Rounded 135 87 Menu Bottom Rounded 85 131 Menu Right Rounded 145 88 Menu Bottom Rounded 95 132 Menu Right Rounded 155 89 Menu Bottom Rounded 105 133 Menu Right Rounded 165 90 Menu Bottom Rounded 115 134 Menu Right Rounded 175 91 Menu Bottom Rounded 125 135 Menu Right Rounded 185 92 Menu Bottom Rounded 135 136 Menu Right Rounded 195 93 Menu Bottom Rounded 145 137 Menu Left Rounded 15 94 Menu Bottom Rounded 155 138 Menu Left Rounded 25 95 Menu Bottom Rounded 165 139 Menu Left Rounded 35 96 Menu Bottom Rounded 175 140 Menu Left Rounded 45 TPD4 Border Styles by Name Cont No Border styles No Border styles 141 Menu Left Rounded 55 149 Menu Left Rounded 135 142 Menu Left Rounded 65 150 Menu Left Rounded 145 143 Menu Left Rounded 75 151 Menu Left Rounded 155 144 Menu Left Rounded 85 152 Menu Left R
69. P OTP e EAP MD5 e MSCHAPv2 e MSCHAP PAP CHAP Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to the EAP Authentication section on page 160 and the Using the Site Survey tool section on page 26 for further details on these security options EAP TLS Settings Press the EAP TLS button to open the EAP TLS Settings page FIG 65 FARANE SSID Identity Genificate Authority Glient Gertiticate Private Key Private Key password Save Cancel FIG 65 Wireless Settings page EAP TLS Settings TLS Transport Layer Security was the original standard wireless LAN EAP authentication protocol TLS requires additional work during the deployment phase but provides additional security since even a compromised password is not enough to break into an EAP TLS protected wireless network environment EAP TLS security is designed for wireless environments where it is necessary to securely transmit data over a wireless network by adding an additional level of security protocol via the use of a private key EAP TLS Settings SSID Service Set Identifier Opens an on screen keyboard for entering the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted t
70. Panel GSN 500 Ball Changes the bargraph slider name or the Joystick cursor name to Ball AICO Syntax Set the icon toa TCO lt vt addr range gt lt button states range gt lt icon index gt button Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state icon index range 0 9900 a value of 0 is clear Example SEND_COMMAND Panel ICO 500 504 amp 510 515 1 amp 2 1 Sets the icon for On and Off states for buttons with variable text ranges of 500 504 amp 510 515 AIRM Pulse the given IR channel for onTime in tenths of seconds Delay offTime in tenths of a Set the IR second before the next IR pulse is allowed IRM allows the command itself to specify the channel port number IRM is needed because commands programmed on the panel itself can only be sent to a single port number currently this is defined as 1 only Note The port number of the IR will be the port number assigned in TPD4 Syntax TRM lt port gt lt channel gt lt onTime gt lt offTime gt Variable port User defined port on the device panel channel 1 255 channel to pulse onTime 1 10th of a second offfime 1 10th of a second Example SEND_COMMAND Panel IRM 10 5 20 10 Sets the port 10 IR channel 5 on time to 1 second and off time to 2 seconds a E A Ri A Button C
71. RY LOSS ARISING OUT OF THE USE OF OR INABILITY TO USE THIS AMX SOFTWARE EVEN IF AMX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITA TION MAY NOT APPLY TO LICENSEE U S GOVERNMENT RESTRICTED RIGHTS The AMX Software is provided with RESTRICTED RIGHTS Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph 1 ii of The Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 or subparagraphs 1 and 2 of the Commercial Computer Software Restricted Rights at 48 CFR 52 227 19 as applicable SOFTWARE AND OTHER MATERIALS FROM AMX COM MAY BE SUBJECT TO EXPORT CONTROL The United States Export Control laws prohibit the export of certain technical data and software to certain territories No software from this Site may be downloaded or exported i into or to a national or resident of Cuba Iraq Libya North Korea Iran Syria or any other coun try to which the United States has embargoed goods or ii anyone on the United States Treasury Department s list of Specially Designated Nationals or the U S Commerce Department s Table of Deny Orders AMX does not authorize the downloading or exporting of any software or technical data from this site to any jurisdiction prohibited by the United States Export Laws This Agreement replac
72. SB USB Programming Cable FG10 5965 MVP HP USB 1 8 Adapter FG5966 23 Memory The MVP 5100 and MVP 5150 come with 128MB of Mobile DDRAM memory and 256 MB NAND Flash memory Neither memory may be upgraded Table Charging Station Connector Locations With the unit facing you the mini USB port for programming and downloading firmware using the AMxX provided adaptor cable and the DC power port are located on the lower left side of the device FIG 3 The connector for the Table Charging Station please refer to the Table Charging Station section on page 7 is located on the bottom of the device Front DC power port A Mini USB port 4 Table Charging Station Connector FIG 3 MVP 5100 5150 side view with programming port The mini USB port is only used for uploading firmware to the device It cannot be used for headphones speakers receiving power or any other function NOTE DP WARNING NOTE Transferring firmware KIT files over a direct USB connection should only be done when the panel is connected to a power supply If battery power fails during a firmware upgrade the panel flash file system may become corrupted Basic Operation The MVP 5100 and MVP 5150 are operated using their integral touchscreens If the device has shut down a touch of the touchscreen will reactivate it Each device s power use allows up to 8 continuous hours of use and up to 96 hours of normal use between recharg
73. Suggest proper format with fixed characters e Right to Left e Required or Optional Change Force a Case Create multiple logical fields e Specify range of characters number for each field With this feature it is not necessary to e Limit the user to a choice of selections e Handle complex input tasks such as names days of the week or month by name Perform complex validation such as Subnet Mask validation Input mask character types These character types define what information is allowed to be entered in any specific instance The following table lists what characters in an input mask will define what characters are allowed in any given position Character Types Character Masking Rule Digit 0 to 9 entry required plus and minus signs not allowed Digit or space entry not required plus and minus signs not allowed Digit or space entry not required plus and minus signs allowed Letter A to Z entry required Letter A to Z entry optional Letter or digit entry required Letter or digit entry optional Any character or a space entry required Ol P sai Mm l OC o Any character or a space entry optional The number of the above characters used determines the length of the input masking box Example 0000 requires an entry requires digits to be used and allows only 4 characters to be entered used Refer to the following Send_Commands for more de
74. Use the following IP Address Under JP address provide an IP address ensure that it is in the same subnet as the IP address given to the USB interface on the device The IP address for the device can be located on the ae a E Systems Settings page of the Protected Settings menu as shown in FIG 33 For more information refer to the Protected Setup Pages section on page 55 System Settings USB P Settings Master eomection System Number Masteder URE E semane Password NOP Neme Device 18002 IP Address FIG 33 IP address location on the System Settings Page Under Subnet mask set the subnet mask to 255 255 255 0 e Do not enter the Gateway or DNS information Click on OK A Do not set USB to the same subnet address as the Ethernet card WARNING 6 Inthe Local Area Connection Properties window click on OK The user should now be able to run any TCP IP application between the two systems After this initial setup the device may be configured solely by downloading the latest LI TPDesign4 file NOTE Configure a Virtual NetLinx Master via USB A Virtual NetLinx Master VNM is used when the target panel is not actually connected to a physical NetLinx Master In this situation the PC takes on the functions of a Master via a Virtual NetLinx Master This connection is made by either using the PC s Ethernet Address via TCP IP using a known PC s IP Address as the Master or using a direct mini
75. When one of the Text Formatting Codes is encountered by the firmware it is replaced with the correct value These values are derived from the following operations Formatting Code Operations Code Operation P Current Value Range Low Value Range High Value Range Low Value x 100 V Current Level Value L Range Low Value H Range High Value S Current State if regular bargraph then resolves to nothing A Current Value Range Low Value R Range High Value Range Low Value Given a current raw level value of 532 a range low value of 500 and a high range value of 600 the following text formatting codes would yield the following strings as shown in the table below Format Display P 32 A out of R 32 out of 100 A of 0 R 32 of 0 100 V of L H 532 of 500 600 ee NOTE Text Area Input Masking Text Area Input Masking may be used to limit the allowed correct characters that are entered into a text area For example in working with a zip code a user could limit the entry to a max length of only 5 characters with input masking this limit could be changed to 5 mandatory numerical digits and 4 optional numerical digits A possible use for this feature is to enter information into form fields The purpose of this feature is to e Force the use of correct type of characters i e numbers vs characters e Limit the number of characters in a text area e
76. able on page 108 for more information Syntax BOR lt vt addr range gt lt border style name or border value gt Variable variable text address range 1 4000 border style name Refer to the Border Styles and Programming Numbers table on page 108 border value 0 41 Examples SEND_COMMAND Panel BOR 500 504 amp 510 515 10 Sets the border by number 10 to those buttons with the variable text range of 500 504 amp 510 515 SEND_COMMAND Panel BOR 500 504 amp 510 AMX Elite M Sets the border by name AMX Elite to those buttons with the variable text range of 500 504 amp 510 515 The border style is available through the TPDesign4 border style drop down list Refer to theTPD4 Border Styles by Name table on page 108 for more information BOS Syntax Set the button to BoS lt vt addr range gt lt button states range gt lt video state gt display either a Variable Video or T Non Video variable text address range 1 4000 window button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state video state Video Off 0 and Video On 1 Example SEND_COMMAND Panel BOS 500 1 1 Sets the button to display video BPP Zero clears the flag Set or clear the protected page flip flag of a button Syntax BPpPp lt vt addr range gt lt protected page flip flag value gt Variable variable text address range
77. allow ping requests to pass through for security reasons When connecting to a NetLinx Master controller via TCP IP the program will first try to ping the controller before attempting a connection Pinging a device is relatively fast and will determine if the device is off line or if the TCP IP address that was entered was incorrect If you decide not to ping for availability and the controller is off line or you have an incorrect TCP IP address the program will try for 30 45 seconds to establish a connection Only One Modero Panel In My System Shows Up Symptom I have more than one Modero panel connected to my System Master and only one shows up Multiple NetLinx Compatible devices such as MVP panels can be associated for use with a single Master Each panel comes with a defaulted Device Number value of 10001 When using multiple panels different Device Number values have to be assigned to each panel 1 Press and hold the two lower buttons on both sides of the display for 3 seconds to open the Setup page 2 Press the Protected Setup button located on the lower left of the panel page enter 1988 into the on screen Keypad s password field and press Done when finished 3 Enter a Device Number value for the panel into the Device Number Keypad The default is 10001 and the range is from 1 32000 Panel Behaves Strangely After Downloading A Panel File Or Firmware Symptom After downloading a panel file or firmware to a G4 device t
78. anel Options Function Show toggles the display of the channel port channel code level port and level code on all touch panel buttons see FIG 49 Telnet enables or disables the panel s telnet server allowing or preventing direct telnet communication to the panel Page Tracking toggles the page tracking function When enabled the panel reports page data to the NetLinx Master NOTE Protected Setup Page Cont System Recovery e Reset System Settings Deletes all of the current configuration parameters on the panel including IP Addresses Device Number assignments Passwords and other presets This option invokes a Confirmation dialog prompting you to confirm your selection before resetting the panel Remove User Pages Removes all TPD4 touch panel pages currently on the panel including the pre installed AMX Demo pages This option invokes a Confirmation dialog prompting you to confirm your selection before removing the panel pages Note that the YES button on the Confirmation dialog is disabled for 5 seconds as additional protection against accidentally resetting the panel or removing the panel pages Reboot Shutdown Panel e Pressing the Reboot button causes the panel to reboot after saving any changes Pressing the Shutdown button causes the panel to shut down after saving any changes Docking Station Channel Code Dock Status Illuminates when the panel is do
79. anel Panel Start Time Displays the time the panel last started or rebooted Bulb Hours Displays the number of hours elapsed with the display on full power nr CON cima NOTE Time amp Date Settings Page The options on the Time amp Date Settings page FIG 45 allows setting and adjusting of time and date information on the NetLinx Master If the time and or date on the Master is modified all connected devices will be updated to reflect the new information Winks PES pairs Get Time Standard Standard AMIRMI 2A Hour Month Set Time Time amp Date Settings Weekday mmidd ddimm Tim aly yyy 12 19 2007 ddimimiyyyy 19 12 2007 tmnth dd yyy December 19 2007 AAt yyy 19 December 2007 Yyyy mmda 2007 12 19 Sar DESAS FIG 45 Time and Date Setup page Both touch panels do not have an on board clock so the only way to modify a panel s time without altering the Master is via NetLinx Code Features on this page include Time amp Date Setup Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Time Date Refresh Set The Get Time button retrieves Time and Date information from the Master The Set Time button retains and saves any
80. anel then sends a EAP Response Identity message through the WAP to the RADIUS server providing its identity and specifying which EAP type it wants to use If the server does not support the EAP type then it sends a failure message back to the WAP which will then disconnect the panel As an example EAP FAST is only supported by the Cisco server 5 Ifthe EAP type is supported the server then sends a message back to the client panel indicating what information it needs This can be as simple as a username Identity and password or as complex as multiple CA certificates 6 The panel then responds with the requested information If everything matches and the panel provides the proper credentials the RADIUS server then sends a success message to the access point instructing it to allow the panel to communicate with other devices on the network At this point the WAP completes the process for allowing LAN Access to the panel possibly a restricted access based on attributes that came back from the RADIUS server e As an example the WAP might switch the panel to a particular VLAN or install a set of farewell rules AMX Certificate Upload Utility The Certificate Upload utility gives you the ability to compile a list of target touch panels select a pre obtained certificate uniquely identifying the panel and then upload that file to the selected panel C This application must be run from a local machine and should not be used from a
81. ange 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state text effect name Refer to the Text Effects table on page 131 for a listing of text effect names Example SEND_COMMAND Panel TEF 500 504 amp 510 515 1 amp 2 Soft Drop Shadow 3in Sets the text effect to Soft Drop Shadow 3 for the button with variable text range 500 504 and 510 515 ATXT Sets Non Unicode text Assign a text string to those buttons with a defined address range Syntax TXT lt vt addr range gt lt button states range gt lt new text gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state new text 1 50 ASCII characters Example SEND_COMMAND Panel TXT 500 504 amp 510 515 1 amp 2 Test Only Sets the On and Off state text for buttons with the variable text ranges of 500 504 amp 510 515 A Button Commands Cont AUNI For the UNI command UN and BMF command the Unicode text is sent as ASCII HEX nibbles Syntax UNI lt vt addr range gt lt button states range gt lt unicode text gt Set Unicode text Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state unicode text Unicode HEX
82. ap ON state Border Color ON state Fill Color ON state Text Color Border Name Opacity Type ITOA CUSTOM TYPE ITOA CUSTOM FLAG ITOA CUSTOM VALUE1 ITOA CUSTOM VALUE2 ITOA CUSTOM VALUE3 CUSTOM TEXT TOA LENGTH STRING CUSTOM TEXT All custom events have the following 7 fields Custom Event Fields Field Description Uint Flag 0 means text is a standard string 1 means Unicode encoded string slong value1 button state number slong value2 actual length of string this is not encoded size slong value3 index of first character usually 1 or same as optional index string text the text from the button text length string encode button text length These fields are populated differently for each query command The text length String Encode field is not used in any command Button Query Commands BCB Syntax Get the current BCB lt vt addr range gt lt button states range gt border color Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1011 Flag zero Value1 Button state number Value2 Actual length of string should be 9 Value3 Zero Text Hex encoded color value ex 000000FF Text length Color name length should be 9 Example SEND COMMAND Panel BCB 529 1 Gets the bu
83. ated by comma space percent or just ran together Syntax BMC lt vt addr range gt lt button states range gt lt source port gt lt source address gt lt source state gt lt codes gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state source port 1 100 source address 1 4000 source state 1 256 codes BM Picture Bitmap BR Border CB Border Color CF Fill Color CT Text Color EC Text effect color EF Text effect FT Font IC Icon JB Bitmap alignment JI Icon alignment JT Text alignment LN Lines of video removed OP Opacity SO Button Sound TX Text VI Video slot ID WW Word wrap on off Example SEND_COMMAND Panel BMC 425 1 1 500 1 BR or SEND_COMMAND Panel BMC 425 1 1 500 1 BR Copies the OFF state border of button with a variable text address of 500 onto the OFF state border of button with a variable text address of 425 Example 2 SEND_COMMAND Panel BMC 150 1 1 315 1 SBRSFTSTX BM ICSCF CT Copies the OFF state border font Text bitmap icon fill color and text color of the button with a variable text address of 315 onto the OFF state border font Text bitmap icon fill color and text color of the button with a variable text address of 150 A Button Commands Cont ABMF Syntax Set any all button
84. ation AM IAN Database Relative Path pa Description f10 28 97 MODE button does NOT send It switches among modes IRN Properties aeea mooo Hand Control pmr Categoy f verion SS Model pmm DOS File Name AM00001 IRL Coreei FIG 85 File Properties window 5 The selected IR file now appears in the NetLinx Studio Workspace FIG 86 Gs Workspace MYP 5100 1 Project s M P 5100 a MYP 5100 Virtual NetLinx Master lt 12 0 0 1 gt amp Source MVP 5100 G Include Module G User Interface amp IR e AMX IRN AMX PLRIR1 1 Gi Other OnLine Tree FIG 86 NetLinx Studio Workspace pane with IR file Adding a personal IR Database file to NetLinx Studio To choose an IR file from a personal IR file database 1 Inthe NetLinx Studio Workspace select Add From User IR Database to open the Select IRN User Database window FIG 87 Select IRN User Database Existing Look in B My Documents img Ea E ary Music 3 Emy Pictures My Recent lag My RoboHelp Projects Documents Emy Videos O Snaglt Catalog Desktop My Documents My Computer My Network File name i 7 Places Files of type IRN Files im z Cancel FIG 87 Select IRN User Database window 2 Select the file from the directory and click Open when finished Programming DP WARNING Overview You can program the MVP 5100 and MVP 5150 using the commands in this section to
85. be required Automatically setting SSID In the Protected Setup page 1 Select Wireless Settings 2 Press the Site Survey button at the bottom of the page 3 Select a WEP secured WAP from within the Site Survey page and press the Connect button FIG 20 Wireless Networks T C s Po Y wer Y coos Toons Roi tt g ve A coa J 0022E242F2 22 Cie i p ve E coa A 2202E302F022 Loo o mo o A e p ve A coa 2200 11 224098 E Sotware Engneeringwap K n A wer A cooo J esooasnisrn Eo mobie tt A omn A coo sa t1 5c 62 11 6s T GE E CY aD a aa S CS a Ga GE VY FIG 20 Site Survey of available WAPs Secured WAP shown selected j Select a target WAP with the desired level of security Connecting to the WAP begins the communication 4 If the security is not handled automatically the information must be entered manually from the Wireless Security menu Manually setting SSID From the Protected Setup page 1 Select Wireless Settings NOTE 2 Locate the Wireless Security menu FIG 21 VT Wireless Security Open Clear Text er FIG 21 Wireless Security page 3 Press the Static WEP button to open the Static WEP Settings dialog FIG 22 iiie VSE SAna SSID tiqi a Required Information Defautt Key _ i SSID Network Name used by the Target WA P Encryption Method WePKeys Hid ed ed amp Passphrase Gurrent Key 41 11 11 11 11 11 11 11 11 11 11 11 11 WEP Key assign
86. cation is used to transfer firmware Kit files and TPD4 touch panel files A mini USB connection is only detected after it is installed onto an active panel Connection to a previously powered panel causes the panel to reboot allows the PC to detect the panel and assigns an appropriate USB driver 1 Verify that the direct USB connection Type A on the panel to mini USB on the panel is configured properly using the steps outlined in the previous two sections 2 With the panel already configured for USB communication and the Virtual Master setup within NetLinx Studio verify that the panel is ready to receive files 3 After the Communication Verification dialog window verifies active communication between the Virtual Master and the panel click the OnLine Tree tab in the Workspace window FIG 72 to view the devices on the Virtual System The default System value is 1 4 Right click on the System entry FIG 72 and select Refresh System to re populate the list Verify the panel appears in the OnLine Tree tab of the Workspace window The default Modero panel value is 1 INS NetLinx Studio Bile Edt view Project Buld Diagnostics Debug Tools Settings window Hep File Edit View Project Build Diagnostics Debug Tools Dos G ua 4 mel gt oO wale Showing the Virtual Master firmware version and device number oo Rae 2 m System 1 Devices E 00000 VNM AMX Corp VNM Version 1 0 JE 32001 NSX
87. cesesssssesseseneseeeees 108 An Button Commands 5 cocecinccpscceteesaseetaceuniated vc suuxuasecauccunnepeexsaeveevsaceuecaubectenveneunnse 111 Miscellaneous MVP Strings back to the Master cccsscsssssssssssscecesesesssesseseeeneeeees 130 MVP Panel Lock Passcode COMMANGG sssssssessssscecesessscsssssssssssseesecesesssessesessneeeees 130 Text Effects Names icscictasscnnstccs cescerocctewstsntecdcxweineseeiices tvenseteebeusdentedussmnrentetcbaabeueeuess 131 Button Query Commands oc 0 c0c lt ccciccssssedencsnoceccesserceseseutnncnpeceeeecessdeseresnsccspeccesestessss 132 Panel Runtime Operations cscsicecs ssccssosescosecsceseeascedessensoupsondos sodasavesssavcoseccecocseseeseeees 141 Inp t COTS cscs csesae Sa cSce cc tectecsanecia cin se punek rens ESSEEN Eri oa SENEESE rE ESES 145 Embedded COGES ic ccscensissnscevcsscensessnusseseriess vos ucbvensenssseecusanewesenceeesseevsckssnmebupeneevees 146 Panel Setup Commands ssssssississsssss3rsscssi soss buccentes sasoecnsndcaneasestacedcioestessoceesdeestacess 147 Battery Life and Replacement sississisessssssessssascsasucncascamnasnesosssesmwenssaenusnaswseussanns 149 OVEIVIEW soens E AE AEE AE OEE EEES 149 Power Management cssssessssevsrsensesisssressecersisorsinsessseesssrsesieseisseesesansisscues irse stvori 149 Battery Replacement sssssrsssteesesssssssssrissssestrseara dss resurss secede ss esris Enss Enee a nEss r stees tiss 150 Appendix A Text Formatting sissssncesncccu
88. cess to a secured workstation Certificate Authority When pressed the panel displays an on screen Certificate Authority CA File Location keyboard which allows you to enter the name of the certificate authority file which is used to validate the server certificate This field is optional If a server certificate is used it should first be downloaded into the panel and the Certificate Authority field should then be set to the name of that certificate file No file path should be used for this setting as all certificates are stored in a specific directory that the user cannot control or change Use the on screen keyboard s Clear button to erase completely any previously stored network path information PEAP Version When pressed this field cycles through the choices of available PEAP PEAPv0 PEAPv1 or PEAPv1 w peaplabel 1 Inner Authentication Type When pressed this field cycles through the choices of available Inner Authentication mechanisms supported by the Devicescape Secure Wireless Client The most commonly used are MSCHAPv2 and GTC e MSCHAPv2 used with PEAPv0 e GTC used with PEAPV1 e OTP e MD5 Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to the EAP Authentication section on page 160 and the Using the Site Survey tool section on page 26 for further details on the
89. cification was the first to be finalized and reach the marketplace The actual throughput obtained from an 802 11b network will typically be between 4 and 5 Mbps Because of the higher frequency and thus shorter wavelength that they use 802 11a signals have a much tougher time penetrating solid objects like walls floors and ceilings As a result the price for 802 1 1a s higher speed is not only a shorter range but also a weaker and less consistent signal 802 11g provides increased bandwidth at 54 Mbps As part of the IEEE 802 11g specification when throughput cannot be maintained this card will automatically switch algorithms in order to maintain the highest spread possible at a given distance In addition 802 11g can also step down to utilize 802 11b algorithms and also maintain a connection at longer distances e IP Routing is a behavior of the wireless routing is largely dependent on the wired network interface Although the panel can be connected to two networks simultaneously it may only have one gateway If the wired network was successfully set up and a gateway was obtained then the default route for all network traffic will be via the wired network In the event that the wired network was not configured then the default route for all network traffic will be via the wireless network The wired network connection always takes priority e Example Imagine a panel connected to the two networks A amp B A is the wired network and B is t
90. cked and communicating with the Charging Station Undock Panel Releases panel from Wall Mounted Charging Station Channel Port 0 20 BUTTON 0 8 0 50 Level Port H taddress Port Channel Code Address Code FIG 49 Function Show example When the Function Show feature is displayed the Channel Port and Code will appear in yellow the Address Port and Code in green and the Level Port and Channel Code in purple The Protected Setup page for the MVP 5100 is slightly different as some of the functions are disabled FIG 50 The particular functions that are disabled are explained in detail in the Protected Setup Navigation Buttons section on page 58 Back Protected Setup System DEyiceND i Rebootsnutdowm Rane Settings Wireless Number Galinge ce Reboot Shutdown Calibrate Control Other p Settings Page Front Button Name Options n Docking Station Telnet Function Show Tracking Setup Access Dock Status System RECOVE y w Undock Panel Reset System Remove User FIG 50 Protected Setup page for the MVP 5100 Rebooting and shutting down the touch panel To reboot either the MVP 5100 or the MVP 5150 1 2 3 4 Access the Protected Setup page Press the Reboot button Wait until the panel completes its reboot Log back into the Protected Setup page if necessary To shut down the panel 1 2 3 Access the Protected Setup page Press the Shutdown button
91. conjunction with any other antenna or transmitter This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body Software License and Warranty Agreement LICENSE GRANT AMX grants to Licensee the non exclusive right to use the AMX Software in the manner described in this License The AMX Software is licensed not sold This license does not grant Licensee the right to create derivative works of the AMX Software The AMX Software consists of generally available programming and development software product documenta tion sample applications tools and utilities and miscellaneous technical information Please refer to the README TXT file on the compact disc or download for further information regarding the components of the AMX Software The AMX Software is sub ject to restrictions on distribution described in this License Agreement AMX Dealer Distributor VIP or other AMX authorized entity shall not and shall not permit any other person to disclose display loan publish transfer whether by sale assignment exchange gift operation of law or otherwise license sublicense copy or otherwise disseminate the AMX Software Licensee may not reverse engineer decompile or disassemble the AMX Software ACKNOWLEDGEMENT You hereby acknowledge that you are an authorized AMX dealer
92. cted Setup pages 1 Press the reset button and hold for 3 to 5 seconds to access the Setup pages 2 Select the Protected Setup button on the left side of the screen 3 Enter the factory default password 1988 into the password keypad to access the page Protected Setup DevicenD BRepoot Shutdown Rane a Secu Settings Wireless a Settings E Reboot Shutdown Name Options O A arc ici Docking Station Function Telnet fej Control Show Othe Settings Page lt Tracking Tools 2 AMX Settings System Recovery aa Ree Broyetem Front Buren a Setup Access Dock Status Undock Panel Remove Pages FIG 48 Protected Setup page for the MVP 5150 showing default values Features on the Protected Setup page for the MVP 5100 include Protected Setup Page Navigation Buttons Back The buttons along on the left side of the page provide access to secondary Protected Setup pages see following sections Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Protected Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Device Number Number Opens a keypad used to view or change the device number of the panel Name Opens a keypad used to view or change the unique device name of the p
93. cter other than those shown in the above table including spaces and symbols A back slash causes the character that follows it to be displayed as the literal character For example A is displayed just as the letter A To define one of the following characters as a literal character precede that character with a back slash Text entry operation using Input Masks A keyboard entry using normal text entry is straightforward However once an input mask is applied the behavior of the keyboard needs to change to accommodate the input mask s requirement When working with masks any literal characters in the mask will be skipped by any cursor movement including cursor backspace and delete keys mow When operating with a mask the mask should be displayed with placeholders The character should mow display where you should enter a character The arrow keys will move between the characters and allow you to replace them The text entry code operates as if it is in the overwrite mode If the cursor is positioned on a character already entered and you type in a new and valid character the new character replaces the old character There is no shifting of characters When working with ranges specified by the mask the keyboard allows you to enter a number between the values listed in the ranges If a user enters a value that is larger than the maximum the maximum number of right most characters is used to create a new accep
94. ctitious name which might be seen by sniffer programs during the initial connection and setup process between the panel and the Radius server In this way the real identity username is protected Typically this is in the form of a fictitious username such as anonymous amx com Password Opens an on screen keyboard Enter the network password string specified for the user entered within the dentity field used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to the password entered to gain access to a secured workstation Certificate Authority When pressed the panel displays an on screen Certificate Authority CA File Location keyboard which allows you to enter the name of the certificate authority file which is used to validate the server certificate This field is optional If a server certificate is used it should first be downloaded into the panel and the Certificate Authority field should then be set to the name of that certificate file No file path should be used for this setting as all certificates are stored in a specific directory that the user cannot control or change Use the on screen keyboard s Clear button to completely erase any previously stored network path information Inner Authentication Type When pressed this field cycles through the choices of available Inner Authentication mechanisms supported include e EAP MSCHAPv2 e EAP GTC EA
95. d by the System Administrator Press Done after entering the IP address information and repeat the same process for the Subnet Mask and Gateway fields Press the optional Host Name field to open the keyboard and enter the Host Name information Press Done after assigning the alpha numeric string of the host name Press the Primary DNS field to open a Keyboard enter the Primary DNS Address provided by the System Administrator and press Done when compete Repeat this process for the Secondary DNS field Press the Domain field to open a Keyboard enter the resolvable domain Address this is provided by the System Administrator and equates to a unique Internet name for the panel and press Done when complete Set up the security and communication parameters between the wireless card and the target WAP by configuring the Wireless Settings section on this page Refer to the following section for detailed procedures to set up either a secure or unsecure connection Using the Site Survey tool This tool allows a user to sniff out all transmitting Wireless Access Points within the detection range of the internal wireless card FIG 16 Once the Site Survey button is pressed the device displays the Site Survey page which contains the following categories Network Name SSID Wireless Access Point names e Channel RF Channel currently being used by the WAP Wireless Access Point e Security Type if detectable such as WEP OPEN and UN
96. ded for an effect however the command will specify both This command sets the location at which the effect will end at Syntax PHP lt popup page name gt lt x coordinate gt lt y coordinate gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PHP Popup1 75 0 Sets the Popup1 hide effect x coordinate value to 75 and the y coordinate value to 0 PHT Set the hide effect time for the specified popup page Syntax PHT lt popup page name gt lt hide effect time gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On hide effect time Given in 1 10ths of a second Example SEND COMMAND Panel PHT Popup1 50 Sets the Popup1 hide effect time to 5 seconds PPA Close all popups on a specified page If the page name is empty the current page is used Same as the Clear Page command in TPDesign4 Syntax PPA lt page name gt Variable page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND_COMMAND Panel PPA Pagel Close all pop ups on Page er CON cml Page Commands Cont PPF Deactivate a specific popup page on either a specified page or the current page If the page name is empty the current page is used see example 2 If the popup page is part of a group the whole group is deac
97. dle bottom first and make sure the device is fully seated in the Charging Station The charger pins in the bottom of the cradle FIG 5 must be in contact with the connector on the bottom of the touch panel for it to start recharging The touch panel will stop recharging automatically once the battery has achieved its maximum charge Charging Station cradle aiik Charger pins Cis e FIG 5 MVP TCS 52 GW Table Charging Station Rear Cleaning the MVP TCS 52 Always use a clean cotton cloth and a spray bottle containing water or a vinegar based cleaner to clean the Table Charging Station as alcohol based cleaners can damage the device Do not directly spray the device instead spray the cloth to prevent moisture from collecting on the charger pins Do NOT use an abrasive of any type to clean the Table Charging Station as this may permanently damage or remove the device s finish Wall Charging Station The optional MVP WCS 52 Wall Charging Station FG5966 1X offers the same recharging and connection features as the Table Charging Station with the advantage of being placed within accessible locations where the table station is either inconvenient or impractical FIG 6 The Wall Charging Station is available in either white FG5966 13 or black FG5966 12 MVP WCS 52 Gear LJ T UJ UJU mamae ONN EENS E DAR REPA MVP 5100 Se Soe ee oe Security Release button FIG 6 MVP WCS 52 GB Wall Charging Station Front The f
98. e The options on the Battery Settings page allow setting of power warning preferences and battery status information and adjustment of the display times for battery warnings FIG 47 SS we Back Battery Settings Low Batten Warming Battery Charge Statis a AET EA TEVA v D Tem Battery Level Banel Shutdown aN Enap Pewveip ennas Cine Ec Disable FIG 47 Battery page Features on this page include Battery Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Charge Status The Charge Status bargraph indicates the power charge available from the battery installed in the panel Low Battery Warning The Up Down buttons adjust the time value in minutes available on the battery for use before the panel displays a low battery warning Range 10 45 default 15 min Panel Shutdown This value determines the number of minutes that would need to pass before the panel automatically shuts down Once shutdown the unit would have to be restarted The Up Down buttons alter the timeout value in minutes A value of 0 disables this feature Range 0 240 default 1200 min Battery One Charge The Battery One Charge Status f
99. e FCC Rules and Industry Canada RSS 210 subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC RF Radiation Exposure Statement This transmitter must not be co located or operating in
100. e Refer to the EAP Authentication section on page 160 for further details on these security options e Refer to FIG 61 for an example of how a typical EAP LEAP system configuration page should appear Z CiscoSecure ACS Microsoft Internet Explorer File Edit View Favorites Tools Help O Bak a a als Search oe Favorites Ka Ae Ma Cisco Systems LEAP User Setup System Configuration M Allow LEAP For Aironet only Global Authentication Setup G Setup EAP MD5 Gy SharedProtie M allow EAP MDS Components This page specifies settings for various authentication protocols Network Configuration AP EAP request timeout seconds 20 EAP Configuration PEAP EAP FAST EAP TLS sE System Configuration Interface Bel Configuration Administration Control Authentication Authentication MS CHAP Configuration M Allow MS CHAP Version 1 M Allow MS CHAP Version 2 LEAP EAP MD5 AP EAP Request Timeout MS CHAP Configuration Be External User Databases Posture manan Validation Network Access Profiles EAP Configuration EAP is a flexible request response protocol for arbitrary authentication information RFC 2284 EAP is layered on top of another protocol such as UDP z ES Applet appPing started start 3 sa Manage Your Server E CiscoSecure ACS Mic PT TJ e trternet L 6 35PM FIG 61 EAP LEAP sample Cisco System
101. e System number associated with the Master listed in the OnLine Tree tab of the Workspace window The Port field is greyed out Click the Reboot Device checkbox This causes the touch panel to reboot after the firmware update process is complete Click Send to begin the transfer The file transfer progress is indicated on the bottom right of the dialog B in FIG 73 After the file transfer is complete the panel will automatically reboot As the panel is rebooting temporarily unplug the USB connector on the panel until the panel has completely restarted Once the first panel page has been displayed reconnect the USB connector to the panel Right click the associated System number and select Refresh System This causes a refresh of all project systems establishes a new connection to the Master and populates the System list with devices on your particular system Confirm that the panel has been properly updated to the correct firmware version Verify you have downloaded the latest firmware file from www amx com and then save the Kit file to your computer A Special Note for Network Interface Connections Due to any USB connection to your PC being made through a Network Interface Connection NIC Windows will automatically make any new NIC connection the Primary connection If this happens the USB address of 12 0 0 x will show up across the PC s network switches as the PC s source address In some cases network administrators wi
102. e gt lt page flip action gt lt page name gt action to a button Variable if it does not variable text address range 1 4000 page flip action Stan dardPage Flip to standard page Prev iousPage Flip to previous page Show Popup Show Popup page Hide Popup Hide Popup page Togg lePopup Toggle popup state ClearG roup Clear popup page group from all pages ClearP age Clear all popup pages from a page with the specified page name ClearA Il Clear all popup pages from all pages page name 1 50 ASCII characters already exist Example SEND COMMAND Panel APF 400 Stan Main Page Assigns a button to a standard page flip with page name Main Page ABAT Syntax Append BAT lt vt addr range gt lt button states range gt lt new text gt non unicode text Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state new text 1 50 ASCII characters Example SEND_COMMAND Panel BAT 520 1 Enter City Appends the text Enter City to the button s OFF state cL A Button Commands Cont BAU Same format as UNI Append Syntax unicode text t BaU lt vt addr range gt lt button states range gt lt unicode text gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for Gene
103. e latest versions of either TPDesign4 or NetLinx Studio2 This USB driver prepares your computer for proper communication with the device For more information please refer to the Upgrading the Modero Firmware via the USB port section on page 85 2 Access the target panel s Protected Setup firmware page and configure the USB communication parameters 3 With the panel successfully communicating with the target computer launch the Certificate Upload Utility e Familiarize yourself with the Certificate Utility User Interface options Locate your certificate file by using the Browse button and navigating to the desired file type 5 Use the drop down arrow in the Local Address field to select direct communication through the USB port er CON cml ne NOTE 10 11 Select the IP Address that corresponds to the virtual IP Address assigned to the USB connection port on the computer The default is 12 0 0 2 Navigate to the Add IP Address field at the bottom left of the interface and enter a value of 1 greater than the virtual USB IP Address For example If the virtual USB IP Address is 10 0 0 1 then add an address for the directly connected panel of 10 0 0 2 This is one greater than the USB address value detected by the utility e A certificate may be sent to ONLY ONE directly connected panel via USB Use the Ethernet port s IP Address to send a server certificate to multiple panel targets Select the IP Address which corres
104. e security options Static WEP Settings Press the Static WEP button to open the Static WEP Settings page FIG 57 Static WEP Settings SSI WEP G47 WEP 128 128 Bit Key Size WEP Keys Gurrent ey 141 11 11 11 11 11 11 11 11 11 11 11 11 Authentication SES Cancel FIG 57 Wireless Settings page Static WEP Settings Static WEP security requires that both a target WAP be identified and an encryption method be implemented prior to establishing communication In addition to providing both Open and Shared Authentication capabilities this page also supports Hexadecimal and ASCII keys Static WEP Settings SSID Service Set Identifier Opens an on screen keyboard to enter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in your wireless network NXA WAP250Gs use AMX as their default SSID e If this field is left blank the panel will attempt to connect to the first available WAP WEP 64 WEP 128 Cycles through the available encryption options 64 or 128 Bit Key Size WEP Wired Equivalent Privacy is an 802 11 security protocol designed to provide wireless security equivalent to wired networks e WEP64 enables WEP encryption usin
105. e whole group is deactivated This command works in the same way as the Clear Group command in TPDesign 4 Syntax PPK lt popup page name gt Variable popup page name 1 50 ASCII characters Name of the popup page Example SEND COMMAND Panel PPK Popup1 Kills the popup page Popup1 on all pages Page Commands Cont PPM A Modal popup page when active only allows you to use the buttons and features on that Set the modality POPUP page All other buttons on the panel page are inactivated of a specific Syntax popup page to PPM lt popup page name gt lt mode gt Modal or NonModal Variable popup page name 1 50 ASCII characters Name of the popup page mode NONMODAL converts a previously Modal popup page to a NonModal MODAL converts a previously NonModal popup page to Modal modal 1 and non modal 0 Example SEND_ COMMAND Panel PPM Popup1 Modal Sets the popup page Popup1 to Modal SEND COMMAND Panel PPM Popup1 1 Sets the popup page Popup to Modal PPN If the page name is empty the current page is used see example 2 If the popup page is Activate a already on do not re draw it This command works in the same way as the Show Popup specific popup page to launch on either a specified page or the current page command in TPDesign4 Syntax PPN lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of t
106. eatures of the MVP WCS 52 include e Full charging of a docked touch panel within approximately 4 5 hours e Touch panel code lock for security e Integrated docking alignment guides for easy docking Panel eject design with mechanical or electronically controlled capabilities MVP WCS 52 Specifications Dimensions HWD 8 375 x 6 09 x 2 19 21 27 cm x 15 46 cm x 5 56 cm Note Always use the cutout installation dimensions for the MVP WCS 52 when installing this unit into various surfaces This SP engineering drawing is available online at www amx com Power Requirements 3A 12 VDC Class II listed power supplemented Startup Power Total 1 7A Requirements Charging 1 1A Ejection 0 6A Weight e Without box 0 85 Ibs 0 39 kg e With box 1 30 Ibs 0 59 kg Available Colors e MVP WCS 52 GW White FG5966 13 MVP WCS 52 GB Black FG5966 12 NOTE MVP WCS 52 Specifications Front Panel Components Securing Magnets Prevent MVP touch panel from falling free during ejection e Security Latch Adds the primary layer of security when mounting an MVP touch panel When the device is inserted this latch grabs onto the rear of the touch panel and secures it to prevent it from being removed Interface Connector Pins A set of retractable pins male that connect to the underside MVP connector strip This connection provides both communication and power between the touch panel and the MVP WCS 52
107. ees 50 Time G Date Settings Page isis ccsicscsscssccnsssasscnsnseteseadsendsnnandechorseneta sdsceacneresncaeanenoesndss 51 Audio Settings Page sssaisssessevesecvnccdecesssevesspnvenecvvensncensssensobesneseedescepevssneseesvenecstuseseeeets 52 Battery Settings Page wcciccciessccssecceccscsecssseesesecestessscensacscse coscasscnsscsiecseassessnceaccoussteeses 53 Protected Setup Pages scisisscisssscisisvacivosdiesseasuiiussicsatatnessasseisausnosnsuseiiunepebsuutionte 55 Rebooting and shutting down the touch panel cccsssesssscceeesesessssssssssssesseseeesensens 57 Protected Setup Navigation Buttons cccccccscesssssssssssssseceeesessesssssssssseeseeeeees 58 System Settings Page sssssssssssssscesesssscesseeseeseeeusaeseeesceeacecsssseeseeseceeseessesseeseeeeees 59 Wireless Settings Page MVP 5150 Onnly cssesssssssssccescssssscssssssssssessseeseseesesssesees 61 Wireless Security sisi scdeccciccccceccssensssesascnceboccecevescrsseapsssesctuoceosedesssoessveusascoupeeesecasterecvrsseee 64 Open Clear Text S tHNgS i iicsccceescceccccesieussecsscccenpbdecccesteensesevevedecsidbusecesdsassvecodueccunpeses 65 Static WEP SettingsS sccscseccesseeeseeseeesseeaeeaseeeeeeeecececeasseeseesseeseeesseesseeseeseesaaes 66 WPA PSK Settings ai cccsiecssasscsscssosccanecteceuntnasasnnaswnavabnens seesso0ssnessensdasseasedenssannasnaswensasenne 67 EAP Security amp Server Certificates Overview ess
108. egrity and origin authentication WPA2 implements the full standard but will not work with some older network cards Both provide good security with two significant issues either WPA or WPA2 must be enabled and chosen in preference to WEP WEP is usually presented as the first security choice in most installation instructions in the Personal mode the most likely choice for homes and small offices a passphrase is required that for full security must be longer than the typical 6 to 8 character passwords users are taught to employ With the RC4 released to the general public the IEEE implemented the Advanced Encryption Standard AES as the cipher engine for 802 111 which the Wi Fi Alliance has branded as WPA2 FIG 90 802 111 WPA2 TKIP MIC AES 802 1x Encryption z Ss 9 9 s lt FIG 90 WPA2 Overview EAP Authentication EAP Extensible Authentication Protocol is an Enterprise authentication protocol that can be used in both a wired and wireless network environment EAP requires the use of an 802 1x Authentication Server also known as a RADIUS server Although over 40 different EAP methods are currently defined the current internal Modero 802 11g wireless card and accompanying firmware only support the following EAP methods listed from simplest to most complex EAP LEAP Cisco Light EAP EAP FAST Cisco Flexible Authentication via Secure Tunneling a k a LEAPv2 The fol
109. emove the checks from each box FIG 77 ci Advanced Settings HEI Adapters and Bindings Provider Order Connections are listed in the order in which they are accessed by network services Connections e AMX Local Area Connection Local Area Connection 25 he Remote Access connections Bindings for Local Area Connection 25 File and Printer Sharing for Microsoft Networks 3 Internet Protocol TCP IP E Client for Microsoft Networks Internet Protocol TCP IP Bay se FIG 77 Bindings for Local area list detail 6 When finished click OK to close the Advanced Settings window and save all changes Uploading IR Codes to the MVP 5100 Since the MVP 5100 communicates with other devices through IR instead of through WiFi making sure that the device has the latest IR codes is vital To ensure that the IR codes installed on the device are the most suitable use NetLinx Studio to upload newly available codes via the AMX IRN database Installation of IR files on the MVP 5100 requires use of the latest version of NetLinx Studio available from www amx com NOTE All IR code files used by NetLinx Studio are in the JRN format These may be created via IREdit available from www amx com supplied from a personal IRN database or from the AMX IRN database To access the available IRN files 1 Launch NetLinx Studio 2 Open the NetLinx Workspace FIG
110. ented in the following sections EAP Authentication goes a step beyond simply encrypting data transfers but also requires that a set of credentials be validated before the client panel is allowed to connect to the rest of the network FIG 59 Please note that no user intervention is necessary during this process as it proceeds automatically based on the configuration parameters entered into the panel 802 1x EAP over Wireless ee ee ee Authentication Server Client Panel Authenticator RADIUS Server supplicant Wireless Access Point FIG 59 EAP security method in process A server certificate file uses a certificate installed in a panel so that the RADIUS server can be validated before the panel tries to connect to it The field name associated with this file is Certificate Authority If a server certificate is used it should first be downloaded into the panel and the Certificate Authority field should then be set to the name of that certificate file No file path should be used for this setting as all certificates are stored in a specific directory that the user cannot control or change The most secure connection method uses a server certificate If no server certificate will be used this field should be left blank If the field contains a file name then a valid certificate file with the same file name must be previously installed on the panel Otherwise the authentication process will fail NOTE EAP LEAP Settings
111. er for it to be operational Battery Replacement The touch panel s battery is intended to last the life of the device but it may be upgraded for additional run time In cases where the battery has reached its effective end of life it may be replaced with the MVP BP 52 Battery Pack Kit FG5966 20 To replace the battery 1 Shut down the device 2 Place the device face down and remove the five screws from the back of the device Two of the screws are at each of the upper corners of the device underneath screw covers Remove the screw covers to access the screws by prying them out of their slots with a screwdriver or similar tool e Reach the remaining screws by removing the long screw cover at the bottom of the device 3 Carefully remove the back of the device making sure not to dislodge the IR emitter panel Disconnect and remove the old battery from the female connector FIG 88 5 Connect the new battery making sure to seat fully the battery s female connector to the male connector in the device Use a clean nonconductive stick or probe to seat the connectors 6 Install the new battery making sure that the label faces outward and the battery connector wiring runs to the left FIG 88 Make sure that the excess battery wiring fits in the space to the bottom left of the battery Excess battery wiring Battery 4 Female connector FIG 88 Battery installation and connection diagram 7 Reattach the back of the
112. es and supersedes all previous AMX Software License Agreements and is governed by the laws of the State of Texas and all disputes will be resolved in the courts in Collin County Texas USA For any questions concerning this Agreement or to contact AMX for any reason please write AMX License and Warranty Department 3000 Research Drive Richardson TX 75082 Table of Contents Introduction assacsneissasiessenesstiessoiasaesdeiesserssssseuisieses saseoseusaasbiassieeunssohuseusuniansaianGuausis 1 MVP 5150 5 2 Modero ViewPoint WiFi Touch Panel sssssssseessesseeeeeeseeees 2 MVP 5100 5 2 Modero ViewPoint IR Touch Panel sssssesesseeseeesseeseeeeeeeeeees 4 Memory srscsisesescssesesorressivessesseusesesere tvvo vneti ssas itse enncsanesicnandnesdnawvenenmnestanteveneesncuateeonenes 5 Table Charging Station Connector Locations essssssssrsesssseseersesererseseseereersseesessee 5 BaSiC Op ration cicsccrieset ccasccecderencsissqoecrestssinveiuc epihasbwatecadeidatieueasechsisivsbesneassnacieoesou ase 6 Audio Video Capabilities aciccicscdccssssssiensaeaticcviincecvetindastenatsekerh cxavuetesuceniustbcusecdcectatavees 6 Power Mana Gemieint iiindccincsvccsinesdesnaseunssntwesiecdonessstiusndsvenbewessauicssnnessnnsnenbonirsenenbessosents 6 Cleaning the Touch Overlay and Case s ccccccissescscccceescsencceessstessosscecsccoseseessssssanssoonses 6 PUCCESSOTIOS eroen ae REE EA EAEE 7 Table Charging Statioiis isssssissro
113. essssssrseseeeesereeeeersesesseeeseeeeeeesesee 68 EAP LEAP Settings sessioissa ese eiaeaen an aae Eoee R E SEE 70 EAP FAST Settings icsisescsssceasetccccestsnsnananasvanensnnnbsssaaesesescdegeedeansasssesensssusnadnaaesesnavssnoasessonss 72 EAP PEAP Settings sisccssciesccdasiascdescadnsanwsasonsdanynunasoss annsecesovadeansascasessonenncadesuceuussweoesesenveses 74 EAP T TLS Steins csceccctessssccvescicectetesanaswtasncsaaedevancdeesdescessecebeshascasssncninenssasaaseawases osesese 76 EAP TLS Settings cisccsescscccessssscdsesnncsasnnasscenaessesssssossesodscacseeasaseddecsaansassunsiseunaessddaseseeecasesss 78 Client Certificate configuration x icss55225c0sies cies tensnseevsescessiececeascesscossseesesedescavsspocsicses 80 Calibration Page sicscseccssesotexceticesseccbescacdiveeceieetsensentensstoodevesdesseioseessdesceedsesexsecassnceees 81 Other Settings isi scdss tne nsecesnicedeecssnesunionecessevnevesnnviessensenccbeebadecedsensansunesesuectedschevasnases 82 Cache Settings Page ds cs iccciiess tisscctcecseessscetesvevssssebedensceccvereeessrosusedaoeesseecesnecesavecsuseedeusoiede 82 Password Settings Page ccccccccccsisstsesssssscsssssceccssssssnssssssossacsoescsecsesesasesssssasesaaccscodesesaess 83 aaa Upgrading Firmware seccnosrursessaocsorsiveneninrennaurseseyianerenmnse ioe E En ae 85 Upgrading the Modero Firmware via the USB port sssssseseseseseeeeeeeeeeeeees 85 Step 1 Configure the panel for a USB Connection Type
114. evice either does not respond to touches on the touch screen or does not register the touch as being in the correct area of the screen Verify that the protective laminate coating on the LCD is removed before beginning any calibration process The protective cover makes calibration difficult because the device cannot calibrate on specific crosshairs when the sheet is pressing on the whole LCD Battery Will Not Hold Or Take A Charge Symptom The battery will not hold or take a charge and shows no indication of charging either on the bargraphs or in the Battery Setup page To keep the battery from being damaged from operating at too low a level the firmware places it into a protected state The panel must have the latest firmware If it doesn t the firmware can be found at www amx com gt Tech Center gt Firmware Files gt Modero 1 Download the firmware into the panel using NetLinx Studio See the Upgrading the Modero Firmware via the USB port section on page 85 2 After loading the firmware power cycle the MVP this is a complete power cycle not a Reboot The panel will now show the current firmware version within the Setup gt Panel Information page 3 Connect the power supply to the panel You will see 2 warning messages on the display e The first one warns that the battery is low and must be charged e The second warning tells you that the battery is in a protected mode 4 Wait a few minutes and then check the Batte
115. field is only valid when the automatic PAC provisioning feature has been enabled via the previous field Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to the EAP Authentication section on page 160 and the Using the Site Survey tool section on page 26 for further details on these security options EAP PEAP Settings Press the EAP PEAP button to open the EAP PEAP Settings page FIG 63 EAR BEAR SSID Identity Password Gentificate Authority PEAR Version Immer Authentication Type FIG 63 Wireless Settings page EAP PEAP Settings PEAP Protected Extensible Authentication Protocol was developed as a way to securely transmit authentication information such as passwords over a wireless network environment PEAP uses only server side public key certificates and therefore does not need a client panel certificate which makes the configuration and setup easier The PEAP protocol has two main versions e PEAPvO e PEAPv1 PEAP uses several inner authentication mechanisms the most common of which are MSCHAPv2 with PEAPvO e GTC with PEAPv1 EAP PEAP security is designed for wireless environments where it is necessary to transmit data securely over a wireless network EAP PEAP Settings SSID Service Set Identifier Opens an on screen keyboard to enter the SSID name used
116. g Station Quick Start Guide Accessories 93 5966 02 PS3 0 Power Supply FG423 44 Other AMX e MVP 5100 Modero Viewpoint IR Touch Panel FG5966 08 Equipment e MVP 5150 Modero Viewpoint Lite Touch Panel FG5966 07 e MVP WCS 52 Wall Charging Station FG5966 1X Powering the MVP TCS 52 The MVP TCS 52 uses a PS3 0 power supply included with the touch panel or available separately from www amx com to provide direct power for the MVP panel both for standard functions and for charging its internal battery 1 Connect the terminal end of the PS3 0 power supply to the PWR connector on the bottom of the MVP TCS 52 2 To prevent wear on the power supply cord and assure that the device s base is in full contact with the table surface press the cord into the locking groove running across the bottom of the device 3 Provide power to the MVP TCS by connecting the PS3 0 cord to an external power source 4 Place the touch panel in the Charging Station cradle guiding it into place with the locking grooves on each side of the cradle When fully seated the touch panel s charging station connector should be in contact with the Charging Station s charger pins FIG 5 Connections and Wiring The PS3 0 is used to supply power to the device by routing incoming power through the connector pins and charge the device s internal battery Recharging To recharge the touch panel slide the device into the Table Charging Station cra
117. g a 64 Bit Key Size All packets are transmitted with their contents encrypted using the Default WEP Key e WEP128 enables WEP encryption using a 128 Bit Key Size All packets are transmitted with their contents encrypted using the Default WEP Key e If the key is not the correct size the system will resize it to match the number of bits required for the WEP encryption mode selected Default Key Cycles through the four available WEP key identifiers to select a WEP key to use As the Default Key value is altered through selection the corresponding Current Key is displayed Each Current Key corresponds to a WEP key This feature is useful for accessing different networks without having to re enter that networks WEP key It is also sometimes used to set up a rotating key schedule to provide an extra layer of security Static WEP Settings Cont WEP Keys This feature provides another level of security by selecting up to four WEP Keys Push any of the four buttons to open an on screen keyboard Both ASCII and HEX keys are supported Up to four keys can be configured for both e An ASCII key utilizes either 5 or 13 ASCII characters e A HEX key utilizes either 10 or 26 Hexidecimal characters Press Done to accept any changes and save the new value Note A 64 bit key will be 10 characters in length while a 128 bit key will be 26 characters in length The length of the key entered determines the level of WEP encrypti
118. h panel contact Pressing the touch screen overlay will return the device to its Active Mode For more information on the battery see the Battery Life and Replacement section on page 149 Cleaning the Touch Overlay and Case Always use a clean cotton cloth and a spray bottle containing water or a vinegar based cleaner when cleaning the device as alcohol based cleaners can damage the device s touch screen overlay Do not directly spray the device instead spray the cloth to clean the touch screen overlay Do NOT use an abrasive of any type to clean the device as this may permanently damage or remove the device s finish Accessories Table Charging Station The MVP 5100 and MVP 5150 may be used with the MVP TCS 52 Table Charging Station FG5966 1X FIG 4 which acts both as a charging station and a direct power connection The charging station is available in either white FG5966 10 or black FG5966 11 FIG 4 MVP TCS 52 GB Table Charging Station Front MVP TCS 52 Specifications Dimensions HWD 8 0 x 4 75 x 3 5 20 32cm x 12 07cm x 8 89cm Weight 65 Ibs 29 kg Rear Connector e 5 pin charging connector on bottom of charging cradle Operating Operating Temperature 0 C 32 F to 40 C 104 F Storage Operating Humidity 20 85 RH Environments Storage Temperature 20 C 4 F to 60 C 140 F Storage Humidity 5 85 RH Included MVP TCS 52 Table Chargin
119. he Wireless Access Point connection in real time None Poor Fair Good Very Good and Excellent SNR Signal Noise Ratio is a measure of the relative strength of a wireless RF connection Given this value and the link quality above you can determine the noise level component of the SNR For example if signal strength is high but the link quality is low then the cause of the link degradation is noise However if signal strength is low and link quality is low the cause would simply be signal strength Wireless Security The options on the Wireless Security section FIG 55 include the wireless security methods supported by the NXA WC80211GCF Wi Fi card These security methods incorporate WPA WPA2 and EAP technology some of which require the upload of unique certificate files to a target panel Refer to the Appendix B Wireless Technology section on page 156 for further information Some encryption and security features may or may not be supported Wireless Security Support 802 11g Wi Fi CF card Open Clear Text e Static WEP 64 bit and 128 bit key lengths WPA PSK EAP security with and without certificates WAP Site Survey Refer to the Configuring Wireless Network Access MVP 5150 Only section on page 23 for more information on configuring the panel for wireless network access using the various security options Wirslsss Saetirisy Open clear Text ETTE Static WEP EAP TLS Wen Pek ERP LEAP
120. he panel behaves strangely If the panel already contains a large enough file subsequent downloads will take up more space than is available and could often corrupt the Compact Flash The demo file that typically ships with G4 panels is one such file Symptoms include e Having to repeat the download e Inability to make further downloads to the panel May get directory errors graphics hierarchy errors etc indicating problems with the Compact Flash e Panel will not boot or gets stuck on AMX splash screen Other problems also started after downloading to a new panel or a panel with a TPD4 file that takes up a considerable amount of the available Compact Flash 1 DO NOT download TPD4 files of large size over the demo pages or any other large TPD4 file 2 First download a small blank one page file to the G4 panel using the Normal Transfer option to send download the page 3 Reboot the device 4 Do your regular file or firmware download Appendix MVP 5100 5150 Modero Viewpoint Touch Panels 167 al EX It s Your World Take Control 3000 RESEARCH DRIVE RICHARDSON TX 75082 USA e 800 222 0193 e 469 624 8000 469 624 7153 fax 800 932 6993 technical support www amx com 12 08 2008 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time
121. he popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PPN Popup1 Main Activates Popup1 on the Main page Example 2 SEND COMMAND Panel PPN Popup1 Activates the popup page Popup1 on the current page PPT Set a specific popup page to timeout within a specified time If timeout is empty popup page will clear the timeout Syntax PPT lt popup page name gt lt timeout gt Variable popup page name 1 50 ASCII characters Name of the popup page timeout Timeout duration in 1 10ths of a second Example SEND COMMAND Panel PPT Popup1 30 Sets the popup page Popup1 to timeout within 3 seconds PPX Close all popups on all pages This command works in the same way as the Clear All command in TPDesign 4 Syntax Wwe PPX ae Example SEND COMMAND Panel PPX Close all popups on all pages Page Commands Cont PSE Set the show effect for the specified popup Syntax PSE lt popup page name gt lt show effect name gt Variable Set the show effect position page to the popup page name 1 50 ASCII characters Name of the page the popup is displayed named show On effect show effect name Refers to the popup effect name being used Example SEND COMMAND Panel PSE Popup1 Slide from Left Sets the Popup1 show effect name to Slide from Left PSP Only 1 co
122. he username and password within the device Select the blank field Username to open the keyboard Set the Username and select Done Select the blank field Password to open the keyboard Set the Password and select Done po Ona Pw Press the Back button to return to the Protected Setup page 10 Press the Reboot button to reboot the device and confirm changes Master Connection to a Virtual Master via Ethernet When configuring the panel to communicate with a Virtual Master on your PC via wireless Ethernet the Master IP URL field must be configured to match the IP Address of the PC Make sure to use the Virtual System value assigned to the Virtual NOTE Master within NetLinx Studio Before beginning 1 Verify that the panel has been configured to communicate with the Wireless Access Point and confirm that the signal strength quality bargraph is On 2 In NetLinx Studio select Settings gt Master Communication Settings from the Main menu to open the Master Communication Settings dialog FIG 37 Master Communication Settings Available System s Configuration Settings lt No Active System Default Settings gt System e E lt Terminal Settings gt a lt No Active System Default Settings gt Configuration Communication Settings OK Cancel FIG 37 Master Communications Settings dialog box 3 Click the Communications Settings button to open the Communications Settings dialog FIG 38 4 Click
123. he wireless network If the Master controller is on either of these networks then it will be reached However if the Master controller is on a different network C then the gateway determines which network interface wired or wireless will be used Wireless Access Points WAPs are the cornerstone of any wireless network A WAP acts as a bridge between a wired and wireless network It aggregates the traffic from all wireless clients and forwards it down the network to the switch or router One WAP may be all that is necessary for a standard installation However more WAPs may be needed depending on the size of the installation its layout and its construction e Wireless Equivalent Privacy WEP Security is a method by which WLANs protect wireless data streams A data stream encrypted with WEP can still be intercepted or eavesdropped upon but the encryption makes the data unintelligible to the interloper The strength of WEP is measured by the length of the key used to encrypt the data The longer the key the harder it is to crack 802 11b implementations provided 64 bit and 128 bit WEP keys This is known respectively as 64 bit and 128 bit WEP encryption 64 bit is generally not regarded as adequate security protection Both key lengths are supported by the Modero product line Whichever level of WEP used using identical settings is crucial CASE SENSITIVE the key length and the key itself on all devices Only devices with common WEP set
124. hen initially installing a MVP 5150 some basic configuration items including network settings and NetLinx settings will need to be set For more information refer to the Protected Setup Pages section on page 55 The MVP 5150 defaults to Ethernet and Auto mode for its Master connection IR Communication Both the MVP 5100 and MVP 5150 may be used as infrared remote devices for other AMX controllers or third party devices The devices can transmit IR over 20 feet 6 10 m from the panel at frequencies of 38KHz and 455KHz as well as up to eight user programmed frequencies between 20KHz and 1 5MHz IR receivers and transmitters on G4 panels share the device address number of the panel Both devices include an IR transmitter for communication between devices The transmitter is located behind the IR Emitter Panel on the back of the device Modero Setup and System Settings All AMX Modero panels including the MVP 5100 and MVP 5150 feature on board Setup pages Use the options in the Setup pages to access panel information and make various configuration changes Accessing the Setup and Protected Setup Pages 1 At any time use the device s stylus to press down and hold the reset button on the left side of the device for 3 5 seconds This opens a release notice to release the button immediately to open the Setup page FIG 13 Gonnection Status pispay mimeout No Encryption n x Connected via Ethernet inactivity kage elie imime
125. ice and tighten them to anchor the device to the box FIG 10 NOTE lt a holes C Plastic back box Neodymium magnets MVP WCS 52 Rubber feet FIG 10 Installation of MVP WCS 52 For ease of installation put each screw on a neodymium magnet in the device s interior compartment to keep them on hand until they are needed 11 After fully seating the screws wipe down the area around the screw holes with the alcohol prep pad from the Installation Kit Take a rubber foot and remove its adhesive backing Put the foot adhesive side down in the slot surrounding the screw hole in the Wall Charging Station Press down firmly to remove any air bubbles from underneath the foot 12 Install a touch panel by placing it into the interior compartment bottom first Press the top of the touch panel until it is flush with the Wall Charging Station The neodymium magnets will hold it in place 13 To remove the touch panel unlock the touch panel see the Unlocking the touch panel section on page 10 for more information and wait for the touch panel to pull away from the Wall Charging Station Once it has been released grip it by the top of the device and pull it free from the Charging Station NOTE Installing the Optional Metal Rough In Box The optional Metal Rough In Box FG037 11 is 10 inches 25 40cm wide at its widest dimension wider than the bezel of the Wall Charging Station and is only intended for pre c
126. ield indicates the power charge currently Status available on the battery Battery One Quality The Battery One Quality field indicates the maximum charge the battery can take Increased use and recharging of the battery will cause the battery s maximum charge to decrease over time Battery Level Port The Battery Level Port field indicates the port being used to report charge status levels back to the NetLinx Master set in TPDesign4 Battery Level The Battery Level field indicates the level being used to report status levels back to the NetLinx Master set in TPDesign4 Battery Power Brightness The DISABLE DISABLED button acts as a power save feature with two options Limit e Disable Clicking on this button deactivates this power save feature The panel will use the Panel Brightness level e Disabled Clicking on this button activates the brightness limit set on the panel conserving battery power Activating this feature causes the panel to function at 80 of full brightness and overrides the Panel Brightness value set on the Setup page Setup Pages 54 MVP 5100 5150 Modero Viewpoint Touch Panels Protected Setup Pages The Protected Setup page FIG 48 provides secured access to advanced panel configuration options including communication and security settings The Protected Setup page is accessed through the Setup page please refer to the Setup Pages section on page 45 To access the Prote
127. ilable from www amx com NOTE Both the MVP 5100 and MVP 5150 use a native RNDIS USB driver for USB over Ethernet communication When the device is connected to the downloading computer see instructions below for more details it creates a new LAN connection and the user will need to supply a static IP address for this to be enabled To enter a static IP address the user must edit the properties of the TCP IP interface of the connection itself This driver is included in the latest version of NetLinx Studio available from www amx com Upgrading the Modero Firmware via the USB port The MVP 5100 and MVP 5150 use a 5 pin CC USB Type A to Mini B 5 Wire programming cable FG10 5965 for programming firmware updates and touch panel file transfer between the PC and the target device If a programming cable is not available it may be purchased from www amx com The Mini USB port for the connector is located on the left side of the device as viewed from the front Before beginning with this section verify that the device is powered and the Type A end of the USB connector is inserted and secure in the PC s USB port The panel must be powered On before connecting the mini USB connector to the panel To guarantee that the upgrade is not interrupted by power loss connecting the device to a power source such as inserting it into a Table Charging Station before beginning the upgrade is highly recommended Establishing a USB connection between the
128. information The result sent to the Master would be ButtonGet Id 529 Type 1006 Flag 0 VALUE1 1 VALUE2 6 VALUE3 0 TEXT TEXT LENGTH 0 Button Query Commands Cont 2JST Syntax Get the current l2gST lt vt addr range gt lt button states range gt text justification Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1004 Flag Zero Value1 Button state number Value2 1 9 justify Value3 Zero Text Blank Text length Zero Example SEND COMMAND Panel JST 529 1 Gets the button OFF state text justification information The result sent to the Master would be ButtonGet Id 529 Type 1004 Flag 0 VALUE1 1 VALUE2 1 VALUES 0 TEXT TEXT LENGTH 0 TEC Syntax Get the current TEC lt vt addr range gt lt button states range gt text effect color Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1009 Flag Zero Value1 Button state number Value2 Actual length of string should be 9 Value3 Zero Text Hex encoded color value ex 000000FF Text length Color name length should be 9 Example SEND COMMAND Panel TEC 529 1 Gets the button OFF s
129. ing firmware updates and touch panel file transfer between the PC and the target panel Note When connecting the panel to PC using a CC USB or compatible cable be sure to power the panel On before attempting to connect the USB cable from the PC to the mini USB port on the panel nr LON cml MVP 5100 Specifications FG5966 08 Cont External Components Cont DC power port 2 5 mm port to power the panel away from a Charging Station Speaker 40hm e 2 Watts 300Hz cutoff frequency NOTE Speaker is only used for feedback beeps and will not transmit standard audio IR Emitters Transmit IR over 20 feet 6 10 m from the panel e IR emitters on G4 panels share the device address number of the panel e Transmits AMX fixed frequencies at 38KHz and 455KHz and 8 user programmable frequencies from 20KHz to 1 5MHz Operating Storage e Operating Temperature 0 C 32 F to 40 C 104 F Environment Operating Humidity 5 85 RH e Storage Temperature 20 C 4 F to 60 C 140 F e Storage Humidity 5 85 RH Included Accessories e MVP 5100 Installation Guide 93 5966 01 PS3 0 Power Supply FG423 30 Other AMX Equipment e MVP TCS 52 Table Charging Station FG5966 1X e MVP WCS 52 Wall Charging Station FG5966 1X e MVP BP 51 NK Replacement MVP 5100 Battery FG 5966 25 e MVP BP 52 Battery Replacement Kit FG5966 20 e MVP STYLUS 52 Stylus Pack of 3 FG5966 30 xx e CC U
130. ings of its internal battery but its battery charge lasts up to 120 hours if the device goes into Asleep Mode during that time The device may be placed in its charging cradle at any time and operated within its cradle The device will automatically go into Asleep Mode after fifteen minutes of inactivity and this limit may be changed at any time Any wireless Internet connection intended for the MVP 5150 will be reconnected within approximately twenty seconds after the device is placed in its charging cradle Depending upon preselected settings either device may be set to go into Awake Mode as soon as it is placed in the cradle Audio Video Capabilities The MVP 5100 has the capability of displaying multiple JPEG and PNG files at one time Power Management Both the MVP 5100 and MVP 5150 utilize a dual voltage external power supply They may be recharged through the supplied PS3 0 Power Supply FG423 30 as well as through the MVP TCS 52 Table Charging Station FG5966 1X or the MVP WCS 52 Wall Charging Station FG5966 1X For more information see the Accessories section on page 7 for details Although the MVP 5100 and MVP 5150 are equipped with mini USB ports the devices cannot be powered through this port The port is only used for uploading firmware When not in active use both devices conserve battery life between chargings In the Asleep Mode the device s entire system is shut down with only wakeup systems powered to detect touc
131. into the wall before setting the screws into the box as excessive torque applied to the screws will damage the box To avoid this the box may be installed with adhesive Test an unobtrusive spot on the back of the box with a sample of the adhesive to check for any adverse reactions before installing the device Accessories 18 MVP 5100 5150 Modero Viewpoint Touch Panels Configuring Communication O WARNING NOTE All control for a MVP 5150 touch panel is established through a NetLinx Master Communication between the MVP and the Master consists of using either Wireless Ethernet DHCP Static IP or USB References to Ethernet in this manual focus on the use of Wireless Ethernet via the MVP 5150 s WiFi Card Configuration for a MVP 5100 touch panel is made through the mini USB port as it does not have a WiFi Card Before commencing verify you are using the latest NetLinx Master and Modero panel specific firmware Verify you are using the latest versions of AMX s NetLinx Studio and TPDesign4 programs Attempting uploads of drivers and firmware with older versions of NetLinx Studio and TPDesign4 will fail In the example below FIG 12 three MVP 5150 devices are shown at varying distances from the two WAP gateways As with any other WAP network the gateways are spaced so as to allow a maximum wireless coverage for the three devices 11g WAP Panel 1 i Panel 3 802 11g WAP FIG 12 System Deployment Diagram W
132. ion number of the G4 firmware loaded on the panel Setup Port Displays the setup port information value being used by the panel High Port Displays the high port port count value for the panel High Address Displays the high address address count value for the panel High Channel Displays the high channel channel count value for the panel High Level Displays the high level level count value being used by the panel Serial Number Displays the specific serial number value assigned to the panel Setup Pages Version Displays the type and version of the Setup pages being used by the panel Screen Width Displays the screen width in pixels MVP 5100 640 pixels Screen Height Displays the screen height in pixels MVP 5100 480 pixels Screen Refresh Rate Displays the video refresh rate applied to the incoming video signal Screen Rotation Displays the degree of rotation applied to the on screen image Power Up Page Displays the page assigned to display after the panel is powered up Start Up String Displays the start up string Wake Up String Displays the wake up string used after an activation from a timeout Sleep String Displays the sleep string used during a panel s sleep mode File System Displays the amount of Compact Flash memory available on the panel RAM Displays the available RAM or Extended Memory module on the p
133. ion status of the Master the connection type Ethernet or USB and to which System the panel is connected e Until a connection is established the message displayed is Attempting via Ethernet or Attempting via USB When a connection is established the message displayed is either Connected via Ethernet or Connected via USB The word Encrypted appears when an encrypted connection is established with a NetLinx Master Note The panel must be rebooted before incorporating any panel communication changes and to detect Ethernet connections Display Timeout Indicates the length of time that the panel can remain idle before activating Asleep mode causing the device to power down e Press the Up Down buttons to increase decrease the Display Timeout setting in 5 second increments Range 0 seconds to 2 hours Set the timeout value to 0 to disable Sleep mode Note Small timeout values maximize the life of the battery charge Disable Timeout on External Power Pressing this button prevents the panel from entering Sleep mode and powering down if it is connected to an external power source such as a Table or Wall Mounted Docking Station Inactivity Page Flip Timeout Indicates the length of time that the panel can remain idle before automatically flipping to a pre selected page e Press the Up Down buttons to increase decrease the Inactivity Page Flip Timeout setting Range 0 240 minutes
134. ired to enter in the remaining WEP key settings e A similar process occurs for WPA PSK access points For any other situation the security mode switches back to the previous page and security and connection parameters must be entered in as usual Step 2 Configure the Card s Wireless Security Settings The second step in setting up the wireless card is to configure the Wireless Settings section of the Wireless Settings page This section configures both the communication and security parameters from the internal wireless card to the WAP The procedures outlined within the following sections for an 802 11g card facilitate a common security configuration to a target WAP Refer to the Appendix B Wireless Technology section on page 156 for more information on other security methods After setting up the wireless card parameters configure the communication parameters for the target Master see Step 3 Choose a Master Connection Mode section on page 33 Configuring the device s wireless card for unsecured access to a WEP In the Protected Setup page 1 Press the Wireless Settings button located on the lower left to open the Wireless Settings page FIG 17 2 Enter the SSID information by e Automatically filling it by pressing the Site Survey button From the Site Survey page choosing an Open WAP from within the Site Survey page and then pressing the Connect button at the bottom of the page FIG 18 Manually entering the SSID inf
135. k or other wall material over the box cut a hole matching the size of the inside diameter in the sheet rock and clean out all dust before proceeding with the installation of the Plastic Back Box Other MVP WCS 52 installations The Wall Mounted Charging Station is designed to be installed in various different locations such as into the face of a wooden podium or the top of a table Depending upon the ability to wire it to a power source Wall Mounted Charging Stations may be installed on vertical or horizontal surfaces composed of such materials as wood brick and glass Installing a Wall Mounted Charging Station into a solid wall thicker than a standard thickness of sheetrock is possible but requires special preparation If installing into a solid wall of concrete or rock a recess must be chiselled or cut out to match the size of the device The box is sized 8 375 inches 21 27cm long and 5 75 inches 14 60cm high so the hole should be at least 1 4 0 64cm smaller in these dimensions To facilitate the full range of movement of the device s components the recess must be at least 2 69 inches 6 83cm deep Ensure that the power cable has been installed in the wall and is accessible by the installer before chiseling out the recess Instead of using the lockdown wings to secure the Plastic Back Box standard concrete screws may be inserted through the screw holes after removing the lockdown wings However drill the concrete screw holes
136. kstation Automatic PAC Provisioning This selection toggles PAC Protected Access Credential Provisioning Enabled automatic or Disabled manual If Enabled is selected the following PAC File Location field is disabled because the search for the PAC file is done automatically If Disabled is selected the user is required to manually locate a file containing the PAC shared secret credentials for use in authentication In this case the IT department must create a PAC file and then transfer it into the panel using the AMX Certificate Upload application Note Even when automatic provisioning is enabled the PAC certificate is only downloaded the first time that the panel connects to the RADIUS server This file is then saved into the panel s file system and is then reused from then on It is possible for the user to change a setting such as a new Identity that would invalidate this certificate In that case the panel must be forced to download a new PAC file To do this set Automatic PAC Provisioning to Disabled and then back to Enabled This forces the firmware to delete the old file and request a new one PAC File Location This field is used when the previous Automatic PAC Provisioning option has been Disabled e When pressed the panel displays an on screen PAC File Location keyboard which allows you to enter the name of the file containing the PAC shared secret credentials for use in authentication e This
137. l in the process The maximum recommended torque to screw in the wings on the plastic back box is 105 IN OZ 74 N CM Applying excessive torque while tightening the wing screws such as with powered screwdrivers can strip out the wings or damage the plastic back box 6 Prepare the captive wires for the 2 pin 3 55 mm mini captive wire connector used for the MVP WCS 52 s power supply Preparing and connecting the captive wires requires the use of a wire stripper and flat blade screwdriver Strip 0 25 inch 6 35 mm of wire insulation off all wires e Insert each wire into the appropriate opening on the connector e Turn the screws clockwise to secure the wires in the connector Do not over torque the screws doing so can bend the seating pins and damage the connector 7 Secure the power cable to the device using either of the two tie wrap anchors included in the Installation Kit at the top rear of the device FIG 9 Point the head of each tie wrap toward the center of the device Tie Wrap Anchors Mini Captive Wire Connector Plug female FIG 9 MVP WCS 52 Rear 8 Firmly seat the mini captive wire connector to the power connector on the device 9 Firmly seat the device against the box Make sure that the tab connector at the top of the device is locked into the box 10 Insert the two installation screws from the MVP WCS 52 Installation Kit into the screw holes in the interior compartment of the dev
138. length Color name length should be 9 Example SEND COMMAND Panel BCT 529 1 Gets the button OFF state text color information The result sent to Master would be ButtonGet Id 529 Type 1013 Flag 0 VALUE1 1 VALUE2 9 VALUE3 0 TEXT FFFFFEFF TEXT LENGTH 9 Button Query Commands Cont BMP Syntax Get the current BMP lt vt addr range gt lt button states range gt bitmap name Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1002 Flag Zero Value1 Button state number Value2 Actual length of string Value3 Zero Text String that represents the bitmap name Text length Bitmap name text length should be 9 Example SEND COMMAND Panel BMP 529 1 Gets the button OFF state bitmap information The result sent to the Master would be ButtonGet Id 529 Type 1002 Flag 0 VALUE1 1 VALUE2 9 VALUE3 0 TEXT Buggs png TEXT LENGTH 9 BOP Syntax Get the overall BOP lt vt addr range gt lt button states range gt button opacity Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1015 Flag Zero Value1 Button state number Value2 Opacity Value3 Ze
139. ll notice the NIC connection and reconfigure any PC that has connected to the MVP 5100 Business college and government installations are the type of installations that would be most affected and most home installations would not be affected To prevent the NIC connection from becoming the primary connection 1 From the Windows Start menu select Settings gt Control Panel to open the Control Panel window 2 Inthe Control Panel window click on the Network Connections icon to open the Network Connections window FIG 74 File Edit Yiew Favorites Tools Advanced Help ae Qt D P search gt Folders 3 Address network Connections sSS SSCSCSC CsCSCSCiY BG Links Alergy Clinic AMX i broadband gt Speed tests E Computer Management F Soffront TRACKWeb 2 Customize Links G Google a Device Name Network Tasks Create anew a LAN or High Speed Inter Connected Intel R PRO 1000 connection Change Windows Firewall settings bLocal Area Connection LAN or High Speed Inter Connected Realtek RTL8139 Fe See Also Local Area Connection 25 LAN or High Speed Inter Connected AMX USB Device Lir A Network Troubleshooter Other Places x B Control Panel J My Network Places My Documents My Computer Details Network Connections ERE S FIG 74 Network Connections window 3 From the Advanced menu select Advanced Settings to open the Advanced Settings window FIG
140. lowing use certificates EAP PEAP Protected EAP EAP TTLS Tunneled Transport Layer Security e EAP TLS Transport Layer Security EAP requires the use of an 802 1x authentication server also known as a RADIUS server Sophisticated Access Points such as Cisco can use a built in RADIUS server The most common RADIUS servers used in wireless networks today are Microsoft Sever 2003 e Juniper Odyssey once called Funk Odyssey Meetinghouse AEGIS Server DeviceScape RADIUS Server Cisco Secure ACS EAP characteristics The following table outlines the differences among the various EAP Methods from most secure at the top of the list to the least secure at the bottom of the list EAP Method Characteristics Method Credential Type Authentication Pros Cons EAP TLS Certificates Certificate is based ona_ e Highest e Difficult to two way authentication Security deploy EAP TTLS Certificates Client authentication is e High Security Moderately Fixed Passwords done via password and difficult to certificates deploy One time passwords e Server authentication is tokens is done via certificates EAP PEAP e Certificates Client authentication is e High Security Moderately Fixed Passwords done via password and difficult to certificates deploy One time passwords e Server authentication is tokens done via certificates EAP LEAP Certificates e Authentication is based on Easy e
141. m Shows UP cccssessssssssssceeeesesesssesseseeeeeees 166 Panel Behaves Strangely After Downloading A Panel File Or Firmware 166 Introduction The MVP 5100 Modero Viewpoint IR Touch Panel FG5966 08 and the MVP 5150 Modero Viewpoint WiFi Touch Panel FG5966 07 are wireless ergonomic devices with all control established through a NetLinx Master or through an IR receiver Both utilize a 5 2 Color Active LCD to display a 800 x 480 pixel image with 262 144 colors The MVP 5150 uses both a pre installed 802 11g WPA WPA2 SDIO wireless card and standard IR communication and the MVP 5100 uses only IR for communication IR Emitters Touch screen Stylus Gear tIS US CAU See EE Sc ee coe FIG 1 MVP 5100 5150 touch panel DC power jack Recessed reset button Mini USB port FIG 2 MVP 5100 5150 side view MVP 5150 5 2 Modero ViewPoint WiFi Touch Panel MVP 5150 Specifications FG5966 07 Dimensions 4 3 4 x 7 9 16 x 13 16 120 7 mm x 191 8 mm x 20 3 mm Weight e 1 25 Ibs 0 57 kg Enclosure Matte black plastic Power Requirements Without Charging Panel with battery fully charged Constant current draw 0 3 A 12 VDC Startup current draw 0 4 A 12 VDC Power Requirements While Charging Panel while charging battery e Constant current draw 1 1 A 12 VDC e Startup current draw 1 3 A 12 VDC Minimum Power Supply Required PS3 0 Powe
142. mation is being sorted in a descending order e Down arrow indicates that the information is being sorted in an ascending order gt If the panel detects more than 10 WAPs the Up Down arrows at the far right side of the page become active blue and allow the user to scroll through the list of entries NOTE 4 Select a desired Access Point by touching the corresponding row The up arrow and down arrow will be grayed out if ten or fewer access points are detected If more are detected then they will be enabled as appropriate so that the user can scroll through the list 5 With the desired WAP selected and highlighted click the Connect button to be directed to the selected security mode s Settings page with the SSID field filled in From there either Cancel the operation or fill in any necessary information fields and then click Save Selecting an Open WEP and WPA PSK Access Point and then clicking Connect will open the corresponding Settings page For any other security mode clicking Connect will only return to the previous page without any information being entered e Inan Open security mode after selection and connection to a target WAP the SSID name of the selected WAP is saved for the open security mode Ina Static WEP security mode after selection and connection to a WEP Access Point the user is then redirected back to the Static WEP security screen where the SSID field is already filled out The user is only requ
143. me will appear in the left column of User Access section The password will also appear in the right column but its characters will be replaced with asterisks No matter how many characters are in an actual password the Password column in the User Access section will always show six asterisks To change a User Access password 1 Press the button corresponding to the user s name in the User Access section 2 Inthe Password keyboard enter the user s password and press Done 3 Press the password button in the right column of the User Access section 4 Enter the new password into the Password keyboard and press Done To view all previous instances of users accessing the device 1 From the Password Settings page press the Enable button to highlight it The MVP 5100 will record all successful and unsuccessful attempts to access the touch panel 2 Press the Record button to send a record to the network Master of all recorded attempts to access the device This record may be retrieved from the Master at any time Upgrading Firmware The MVP 5100 and MVP 5150 come already loaded with on board firmware which is upgradeable through the use of the latest version of NetLinx Studio Refer to the NetLinx Studio version 2 x or higher Instruction Manual for more information on how to download firmware to a touch panel C Programming the MVP 5100 and MVP 5150 require the use of the latest versions of NetLinx Studio and TPDesign 4 both ava
144. ment Authentication Method Authentication FIG 22 Wireless Settings page Static WEP security method 4 Press the SSID field From the Network Name SSID keyboard enter the SSID name used by the target Wireless Access Point case sensitive and press Done when finished The card should be given the SSID used by the target WAP If this field is left blank the device will attempt to connect to the first available WAP One of the most common problems associated with connection to a WAP arises because of an improperly entered SSID The same case must be maintained when entering this information ABC is not the same as Abc e The alpha numeric string is AMX by default but can later be changed to any 32 character entry This string must be duplicated within the Network Name SSID field on the WAP As an example if the SSID is MINISTRY this word and the case within must match both the Network Name SSID field on the touch panel s Network Name SSID field and on the WAP s Basic Wireless Configuration page 5 Toggle the Encryption field FIG 22 until it reads either 64 Bit Key Size or 128 Bit Key Size The 64 128 selection reflects the bit level of encryption security This WEP encryption level must match the encryption level being used on the WAP WEP will not work unless the same Default Key is set on both the panel and the Wireless Access Point For example if the Wireless Access Point has been set to default key 4
145. municating touch panel complete all of the steps outlined within the previousAutomatically setting SSID section on page 29 Navigate back to the Wireless Settings page on each panel Verify that all communicating Modero panels are using the same SSID encryption level Default Key and an identical Current Key value e Asan example all panels should be set to Default Key 1 and be using aa bb cc dd ee as the Current Key string value This same Key value and Current Key string should be used on the target WAP Repeat steps 3 on each panel O WARNING Step 3 Choose a Master Connection Mode Since the MVP 5150 may connect with a Master via USB or Ethernet this requires a decision on the type of connection to be made between it and the Master The MVP 5100 may only use USB for connection To establish a Master connection 1 From the Protected Setup page select System Settings 2 Select Type to toggle between the Master Connection Types USB and Ethernet FIG 25 e A USB connection is a direct connection from the panel s mini USB port to a corresponding USB port on the PC acting as a Virtual Master e A wireless Ethernet connection involves indirect communication from the panel to a Master via a wireless connection to the network Transferring firmware KIT files over a USB connection should only be done when the panel is connected to a power supply If battery power or the wireless connection fails during a firmware u
146. n still does not turn green complete the procedures in the following section to set up the Virtual Master and refresh the System from the Online Tree This action sends out a request to the panel to respond and completes the communication turning the System Connection icon green 8 Repeat steps 2 and 3 to return to the System Settings page Step 2 Prepare Studio for communication via the USB port 1 From the Start menu in Windows XP open the Network Connections dialog Start gt Settings gt Network Connections gt Local Area Connection 2 Look for the Local Area Connection reading Local Area Connection AMX USB Device Link and double click on it to open the Local Status 3 Press the Properties tab to open the Local Area Connection Properties section 4 Press the Properties button to open the TCP IP Properties dialog box g Set the IP address to an address within the same subnet as the panel IP address specified within the USB IP settings of the panel For instance if the default IP address on the device is 12 0 0 2 set the IP address to 12 0 0 1 Set the Subnet Mask to 255 255 255 0 In the TCP IP Properties dialog box click OK In the Local Area Connection Properties section click Close po On Launch NetLinx Studio 2 x and select Settings gt Master Communication Settings from the Main menu to open the Master Communication Settings dialog FIG 69 Master Communication Settings Available System s
147. ncel discard changes and return to the previous page e Refer to the EAP Authentication section on page 160 for further details on these security options e Refer to the Using the Site Survey tool section on page 26 for more information on using this feature NOTE Client certificate configuration A client certificate can be configured by an IT department in several ways The client certificate and private key can both be incorporated into one file or split into two separate files In addition the file format used by these files could be PEM DER or PKCS12 These formats are described later in this section The following table describes how to fill in the fields for each possible case Client Certificate Configuration Certificate Configuration Client Certificate Field Private Key Field Single file contains both the client certificate and Enter the file name Enter the same file name the private key Format is PEM or DER First file contains the client certificate second file Enter the first file name Enter the second file name contains the private key Format is PEM or DER Single file contains both the client certificate and Leave this field blank Enter the file name the private key Format is PKCS12 First file contains the client certificate second file Not supported Not supported contains the private key Format is PKCS12 AMX supports the following security certificates PEM P
148. nel Information page which contains detailed information on the panel itself To access these pages 1 Press and hold the Information button until the Project Information button and the Panel Information button slide from the left The Project Information and the Panel Information buttons will be displayed for three seconds before they slide back behind the Information button whether or not the Information button is still being pressed NOTE 2 Press the appropriate button for the information required 3 To return to the Setup page press the Back button Project Information Page The Project Information page displays the project properties of the TPDesign4 project file currently loaded on the panel FIG 43 Project Information FileName OnlineEventsProgram5150 TP4 Baila Wumber Designer a Jeff Hamner Siioni Bit Wt Thu Oct 14 10 16 08 2004 File Revision Revision Date Thu Oct 14 10 40 48 2004 DealeriD FRETAR Tue Sep 23 09 52 59 2008 dob Name Bink Rate Sales Order JH Commens Purchase order AULA Hai R 36K 0 455K 0 User IR Ponts 0 0 0 O 0 0 0 0 Cradle Sensor Port Gradie Sensor Channel FIG 43 Project Information page Features on this page include Project Information Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Setup page provides a constant visual indication of current connection status Note a Lock appea
149. ngs page FIG 60 on page 70 EAP LEAP security is designed for wireless environments where it is not required to have both a client or server certificate validation scheme in place yet necessary to securely transmit data over a wireless network Refer to the EAP LEAP Settings section on page 70 EAP FAST This button opens the EAP FAST Settings page FIG 62 on page 72 EAP FAST security is designed for wireless environments where security and ease of setup are equally desirable Refer to the EAP FAST Settings section on page 72 for further details RF Link Info These options set communication values for the wireless interface card SSID Displays the currently used SSID of the target WAP Channel The RF channel being used for connection to the WAP read only Link Quality Displays the quality of the link from the wireless NIC to the Wireless Access Point direct sequence spread spectrum in real time None Poor Fair Good Very Good and Excellent Even when link quality is at its lowest you still have a connection and the ability to transmit and receive data even if at lower speeds Note Link Quality and Signal Strength are applicable to RF connections only It is possible to have an RF signal to a WAP but be unable to communi cate with it because of either incorrect IP or encryption settings Signal Strength This indicator displays a description of the signal strength from t
150. nt page is used see example 2 If the popup page is already On do not re draw it This command works in the same way as the Show Popup command in TPDesign4 Syntax PPON lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of the popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PPON Popup1 Main Activates the popup page Popup1 on the Main page Example 2 SEND _COMMAND Panel PPON Popup1 Activates the popup page Popup on the current page Programming Numbers The following information provides the programming numbers for colors fonts and borders Colors can be used to set the colors on buttons sliders and pages The lowest color number represents the lightest color specific display the highest number represents the darkest display For example 0 represents light red and 5 is dark red RGB triplets and names for basic 88 colors RGB Values for all 88 Basic Colors Index No Name Red Green Blue 00 Very Light Red 255 0 0 01 Light Red 223 0 0 02 Red 191 0 0 03 Medium Red 159 0 0 04 Dark Red 127 0 0 05 Very Dark Red 95 0 0 06 Very Light Orange 255 128 0 07 Light Orange 223 112 0 08 Orange 191 96 0 09 Medium Orange 159 80 0 10 Dark Orange 127 64 0 11 Very Dark Orange 95 48 0 12 Very
151. nter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in the wireless network NXA WAP250Gs use AMX as their default SSID e With EAP security the SSID of the WAP must be entered If it is left blank the panel will try to connect to the first access point detected that supports EAP However a successful connection is not guaranteed because the detected WAP may be connected to a RADIUS server which may not support this EAP type and or have the proper user identities configured EAP TTLS Settings Cont Identity Opens an on screen keyboard Enter an EAP Identity string used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to a username used to login to a secured server or workstation This works in tandem with the Password string which is similar to the password entered to gain access to a secured workstation Typically this is in the form of a username such as jdoe amx com Anonymous Identity Opens an on screen keyboard Enter an IT provided alpha numeric string which similar to the username used as the identity but that does not represent a real user This information is used as a fi
152. o join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in the wireless network NXA WAP250Gs use AMX as their default SSID e With EAP security the SSID of the WAP must be entered If it is left blank the panel will try to connect to the first access point detected that supports EAP However a successful connection is not guaranteed because the detected WAP may be connected to a RADIUS server which may not support this EAP type and or have the proper user identities configured Identity Opens an on screen keyboard for entering an EAP Identity string used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to a username used to login to a secured server or workstation This works in tandem with the Password string which is similar to the password entered to gain access to a secured workstation Typically this is in the form of a username such as jdoe amx com EAP TLS Settings Cont Certificate Authority When pressed the panel displays an on screen Certificate Authority CA File Location keyboard for entering the name of the certificate authority file which is used to validate the server certificate This field is optional If a server certificate is used it should first be downloaded into the panel and the Certificate Authority field should then be set to the name of that cer
153. ollowing locations Zero can be used for an absolute position Example SEND_COMMAND Panel JSI 500 504 amp 510 515 1 amp 2 1 Sets the Off On state icon alignment to upper left corner for those buttons with variable text range of 500 504 amp 510 515 A Button Commands Cont AJST Set text alignment using a numeric keypad layout for those buttons with a defined address range The alignment of 0 is followed by lt left gt lt top gt The left and top coordinates are relative to the upper left corner of the button Syntax JST lt vt addr range gt lt button states range gt lt new text alignment gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state new text alignment Value of 1 9 corresponds to the following locations Example SEND_COMMAND Panel JST 500 504 amp 510 515 1 amp 2 1 Sets the text alignment to the upper left corner for those buttons with variable text ranges of 500 504 amp 510 515 AMBT Set the Mouse Button mode On for the virtual PC Syntax MBT lt pass data gt Variable pass data 0 None 1 Left 2 Right 3 Middle Example SEND COMMAND Panel MBT 1 Sets the mouse button mode to Left Mouse Click AMDC Syntax Turn On the t Mpc n Mouse Example double click p feature for the
154. ommands Cont JSB Set bitmap picture alignment using a numeric keypad layout for those buttons with a defined address range The alignment of 0 is followed by lt left gt lt top gt The left and top coordinates are relative to the upper left corner of the button Syntax JSB lt vt addr range gt lt button states range gt lt new text alignment gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state new text alignment Value of 1 9 corresponds to the following locations Zero can be used for an absolute position Example SEND_COMMAND Panel JSB 500 504 amp 510 515 1 amp 2 1 Sets the off on state picture alignment to upper left corner for those buttons with variable text ranges of 500 504 amp 510 515 AJSI Set icon alignment using a numeric keypad layout for those buttons with a defined address range The alignment of 0 is followed by lt left gt lt top gt The left and top coordinates are relative to the upper left corner of the button Syntax t 7SI lt vt addr range gt lt button states range gt lt new icon alignment gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state new icon alignment Value of 1 9 corresponds to the f
155. on employed 64 or 128 bit 128 bit keys may be used if supported by the internal wireless card Current Key Displays the current WEP key in use e When working with a single panel and a single WAP manually entering the Current Key from the WAP into the selected WEP Key is recommended e When working with a single WAP and multiple panels generating a Current Key using the same passphrase on all panels and then entering the panel produced WEP key manually into the Wireless Access Point is recommended e Keys may also be examined by touching the key buttons and noting the keyboard initialization text e Use the on screen keyboard s Clear button to erase stored key information Authentication Toggles between the two authentication modes Open broadcast publicly or Shared encrypted e An Open network allows connections from any client without authentication e A Shared network requires the client to submit a key which is shared by the network WAP before it is given permission to associate with the network In this case the key is the same as the WEP encryption key In either case if WEP encryption has been enabled the client will still require the WEP key to encrypt and decrypt packets in order to communicate with the network Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to
156. on in the Transport Connection Option section 6 Click the Edit Settings button to open the Virtual NetLinx Master Settings dialog FIG 36 Virtual NetLinx Master Settings Master System Number ft The Virtual NetLinx Master connection allows G4 devices to a directly connect to NetLinx Studio instead of a physical NetLinx Current Connection 10 0 0 1 Master for transfers Available Connections IP Address 192 168 224 135 Broadcom NetXtreme Gigabit Ethernet Packet Scheduler Miniport OK Cancel FIG 36 Virtual NetLinx Master Settings dialog box 7 Select the IP Address for the AMX USB device in the Available Connections section The IP address will appear in the Current Connection field Click OK to save the settings and close the window 8 In the Communications Settings dialog box the IP address for the Virtual NetLinx Master will appear in the display field Click OK to save the settings and close the window 9 Inthe Master Communications Settings dialog box the Virtual Master IP address appears in the Configuration field Click OK to save the settings and close the window 10 Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System 11 Right click on Empty Device Tree System and select Refresh System to re populate the list e The System Connection status button turns green after a few seconds to indicate an active USB connection to the PC via the Virtual Master Ifthe Sy
157. on the Virtual NetLinx Master radio button from the Platform Selection section to indicate that you are working as a NetLinx Master 5 Click on the Virtual NetLinx Master radio box from the Transport Connection Option section to indicate wanting to configure the PC to communicate with a panel Everything else such as the Authentication is greyed out because the procedure is not being made through the Master s UI 6 Click the Edit Settings button in the Communications Settings dialog to open the Virtual NetLinx Master Settings dialog 7 From within this dialog enter a unique System number default is 1 and note the IP Address of the target PC being used as the Virtual Master i Communication Settings m Platform Selection i F Transport Connection Option NetLing Master TCPAP Edit Settinas C Axcess Master Serial eu Authentication Required C Virtual NetLins Master coca FIG 38 Communications Settings dialog box 8 Click OK to close the open dialogs save the settings and return to the main NetLinx Studio application 9 Place the panel in the Table Charging Station or in the Wall Charging Station 10 After the panel powers up press and hold down the reset button for 3 seconds to continue with the setup process and proceed to the Setup page 11 Select Protected Setup gt System Settings to open the System Settings page FIG 39 System Settings The System Number is gt
158. on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in the wireless network NXA WAP250Gs use AMX as their default SSID e With EAP security the SSID of the WAP must be entered If it is left blank the panel will try to connect to the first access point detected that supports EAP However a successful connection is not guaranteed because the detected WAP may be connected to a RADIUS server which may not support this EAP type and or have the proper user identities configured Identity Opens an on screen keyboard to enter an EAP Identity string used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to a username used to login to a secured server or workstation This works in tandem with the Password string which is similar to the password entered to gain access to a secured workstation Typically this is in the form of a username such as jdoe amx com Password Opens an on screen keyboard to enter the network password string specified for the user entered within the dentity field used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to the password entered to gain ac
159. onstruction installations FIG 11 The Metal Rough In Box is used in conjunction with the Wall Charging Station s plastic back box The Metal Rough In Box must be located behind 3 8 0 95cm to 3 4 1 91cm of wall mounting surface material Install front surface of box flush with surface of wall stud FIG 11 Typical Metal Rough In Box Installation The Metal Rough In Box bears a wing on each corner which is intended to bridge gaps between studs and or spacers These wings may be bent carefully in order to fit a particular gap but may not be so bent as to allow the box to hang in a vertical position Once placed in the desired position put at least one screw through each wing into the adjoining stud or spacer to secure it The interior of the box contains a set of holes on either side as well as top and bottom for standard 1 4 inch screws Use these holes to anchor the box to its adjoining studs or spacers Ensure that the metal rough in box is flush with the 2x4 studs Any overhang will affect the installation of the covering sheetrock as well as affect the placement of the Plastic Back Box The box has two sets of knockouts in the top and bottom one of the set for US wiring and one for international wiring Make sure that the power cable has been pulled through the metal rough in box by the resident electrician before continuing the installation After completing the installation of the Metal Rough In Box install sheet roc
160. or Numbers Color name R G B alpha colors RRGGBBAA and R G amp B colors values RRGGBB BDO Set the button draw order Determines what order each layer of the button is drawn Syntax t Bpo lt vt addr range gt lt button states range gt lt 1 5 gt lt 1 5 gt lt 1 5 gt lt 1 5e lt l 550 Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state layer assignments Fill Layer 1 Image Layer 2 Icon Layer 3 Text Layer 4 Border Layer 5 Note The layer assignments are from bottom to top The default draw order is 12345 Example SEND_COMMAND Panel BDO 530 1 amp 2 51432 Sets the button s variable text 530 ON OFF state draw order from bottom to top to Border Fill Text Icon and Image Example 2 SEND_COMMAND Panel BDO 1 0 12345 Sets all states of a button back to its default drawing order BFB Set the feedback type of the button ONLY works on General type buttons Syntax BFB lt vt addr range gt lt feedback type gt Variable variable text address range 1 4000 feedback type None Channel Invert On Always on Momentary and Blink Example SEND_COMMAND Panel BFB 500 Momentary Sets the Feedback type of the button to Momentary A Button Commands Cont ABIM Set the input mask for the specified address
161. ord users in the order in which they accessed the device Enable Enabled When enabled this button notes that all password entry attempts will be recorded Report When enabled this button sends a report to the Master on any attempts or successes at entering a password To change a previously established password 1 In the Password Settings page press the button in the In Panel Password Change section for the particular password to be changed Password 5 is protected and can only be changed by the Administrator NOTE 2 Inthe Password keyboard enter the new alphanumeric password 3 Press Done when complete eee NOTE NOTE The User Access section allows the Administrator to control access of all individuals using or attempting to use the MVP 5100 From this section new users may be given access rights to the device however they will NOT be given access to the Protected Settings page Only one of the main passwords may be used to access the Protected Settings page An individual user password may not be used to access the Protected Settings page unless it matches one of the main passwords To list a new user within the User Access section 1 Press a blank button in the User Access section 2 Inthe Name keyboard enter the user s name or nickname and press Done when finished 3 In the Password keyboard enter the selected alphanumeric password and press Done when finished 4 The new user s na
162. ordinate is ever needed for an effect however the command will specify both This command sets the location at which the effect will begin Syntax PSP lt popup page name gt lt x coordinate gt lt y coordinate gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PSP Popup1 100 0 Sets the Popup1 show effect x coordinate value to 100 and the y coordinate value to 0 PST Set the show effect time for the specified popup page Syntax PST lt popup page name gt lt show effect time gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On show effect time Given in 1 10ths of a second Example SEND COMMAND Panel PST Popup1 50 Sets the Popup1 show effect time to 5 seconds PAGE Flip to a specified page Flips to a page with a specified page name If the page is currently active it will not redraw the page Syntax PAGE lt page name gt Variable page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND_COMMAND Panel PAGE Pagel Flips to page Page Commands Cont PPOF Deactivate a specific popup page on either a specified page or the current page If the page name is empty the current page is used see example 2 If the popup page is part of a group the whole group is deactivated This command
163. ormation into the appropriate fields by following steps 7 through 9 3 From within the Wireless Security section press the Open Clear Text button to open the Open Clear Text Settings dialog FIG 19 An Open security method does not utilize any encryption methodology but does require that an alpha numeric SSID be entered This method sends out network packets as unencrypted text 4 Press the red SSID field to display an on screen Network Name SSID keyboard i Wireless Settings pectine W Wireless secunty ro oe Toler ERTIES Wireless card AE si Sete security settings IP info re m lt None Poor Fair Good Very Good re Excellent FIG 17 Wireless Settings page showing a sample unsecured configuration Wireless Networks 00E00FR26 MY 3 02 EA 02 00 22E2 42F2 72 2E3 22FD 22 220C 11 2240 9B 6690 46 11 57 11 5 Select an OPEN unsecured WAP 2 TURELELE 000000000 D00 000000 WAT Connecting to the WAP begins the communication FIG 18 Site Survey of available WAPS Unsecured WAP shown selected Required information SSID Network Name used by the Target WAP Ojan Sir E0 Sineo s550 By default this field displays the SSID AMX SEWS Cancel FIG 19 Wireless Settings page Open Clear Text security method 5 In this keyboard enter the SSID name used on the target Wireless Access Point case sensitive e The card should be given the SSI
164. ounded 165 145 Menu Left Rounded 95 153 Menu Left Rounded 175 146 Menu Left Rounded 105 154 Menu Left Rounded 185 147 Menu Left Rounded 115 155 Menu Left Rounded 195 148 Menu Left Rounded 125 A Button Commands These Button Commands are used in NetLinx Studio and are case insensitive All commands that begin with have the capability of assigning a variable text address range and button state range A device must first be defined in the NetLinx programming language with values for the Device Port System in all programming examples Panel is used in place of these values e Variable text ranges allow you to target 1 or more variable text channels in a single command e Button State ranges allow you to target 1 or more states of a variable text button with a single command e Character is used for the through notation also the amp character is used for the And notation A Button Commands ANI Syntax Run a button ANI lt vt addr range gt lt start state gt lt end state gt lt time gt animation Variable in 1 40 second 2029S variable text address range 1 4000 start state Beginning of button state 0 current state end state End of button state time In 1 10 second intervals Example SEND_COMMAND Panel ANI 500 1 25 100 Runs a button animation at text range 500 from state 1 to state 25 for 10 second APF Syntax Add page flip APF lt vt addr rang
165. own time gt Variable variable text address range 1 4000 bargraph slider color or joystick cursor color second bargraph ramp down time In 1 10th of a second intervals Example SEND_COMMAND Panel GRD 500 200 Changes the bargraph ramp down time to 20 seconds AGRU Syntax Change the GRU lt vt addr range gt lt bargraph ramp up time gt bargraph Variable ramp up time in 4 10th of a variable text address range 1 4000 second bargraph ramp up time In 1 10th of a second intervals Example SEND_COMMAND Panel GRU 500 100 Changes the bargraph ramp up time to 10 seconds AGSC A user can also assign the color by Name and R G B value RRGGBB or RRGGBBAA Change the Syntax GSC lt vt addr range gt lt color value gt Variable variable text address range 1 4000 color value Refer to the RGB Values for all 88 Basic Colors table on page 105 Example SEND_COMMAND Panel GSC 500 12 Changes the bargraph or joystick slider color to Yellow A Button Commands Cont AGSN Slider names and cursor names can be found in the TPDesign4 slider name and cursor Change the drop down list bargraph slider Syntax name or joystick cursor name t GSN lt vt addr range gt lt bargraph slider name gt Variable variable text address range 1 4000 bargraph slider name See table below Bargraph Slider Names i e a cls al w i a A Example SEND_COMMAND
166. ox The box has two knockouts at the top left and the top right NOTE WARNING To assist with wiring and to avoid mechanical stresses on the wire and the mechanism of the Wall Mounted Charging Station the top right knockout is preferred for use 3 Run the power cable through the knockout into the box Pull out about six inches 15 25cm of cable into the box to facilitate installation of the MVP WCS 52 4 Slide the plastic back box into the hole being careful not to twist or pinch the cable and set it flush with the wall FIG 8 Make sure that all of the lockdown wings are folded into their slots before attempting to insert the box For ease of installation the inside of the box has the direction UP labeled for reference All lockdown wings folded flat during installation Note Orientation Designator FIG 8 Installation of plastic back box 5 Extend the wings on the sides of the box by tightening the screws inside the box Not all of the wings must be extended to lock the box in place but extending a minimum of the top and bottom wings is highly recommended Apply enough pressure to the screw head to keep the box flush with the wall this ensures that the wing will tighten up against the inside of the wall Make absolutely certain that the box is in its intended position Once the box lockdown wings are extended within the box s hole within the wall removing the box will be extremely difficult without damaging the wal
167. p from center and 80 down from center Horizontal 60 left from center and 60 right from center 1 2 NOTE MVP 5150 Specifications FG5966 07 Cont External Components Connector 5 pin Mini USB connector used for output to USB programming firmware update and touch panel file transfer between the PC and the target panel Note When connecting the panel to PC using a CC USB or compatible cable be sure to power the panel On before attempting to connect the USB cable from the PC to the mini USB port on the panel DC power port 2 5 mm port to power the panel away from a Charging Station Speaker 4 Ohm 2 Watts 300Hz cutoff frequency NOTE Speaker is only used for feedback beeps and will not transmit standard audio Audio Standards e G711 sound standard e 75dB SPL 1m IR Emitters Transmit IR over 20 feet 6 10 m from the panel e IR emitters on G4 panels share the device address number of the panel e Transmits AMX fixed frequencies at 38KHz and 455KHz and 8 user programmable frequencies from 20KHz to 1 5MHz Operating Storage e Operating Temperature 0 C 32 F to 40 C 104 F Environment Operating Humidity 5 85 RH Storage Temperature 20 C 4 F to 60 C 140 F e Storage Humidity 5 85 RH Included Accessories MVP 5150 Installation Guide 93 5966 08 PS3 0 Power Supply FG423 30 Other AMX Equipment e MVP TCS 52 Table Charging
168. perform a wide variety of operations using Send_Commands and variable text commands A device must first be defined in the NetLinx programming language with values for the Device Port System in all programming examples Panel is used in place of these values and represents all Modero panels Verify you are using the latest NetLinx Master and Modero firmware as well as the latest version of NetLinx Studio and TPD4 Page Commands These Page Commands are used in NetLinx Programming Language and are case insensitive Page Commands APG Add the popup page to a group if it does not already exist If the new popup is added to a group which has a popup displayed on the current page along with the new pop up the Add a specific displayed popup will be hidden and the new popup will be displayed popup page toa specified popup Syntax group APG lt popup page name gt lt popup group name gt Variable popup page name 1 50 ASCII characters Name of the popup page popup group name 1 50 ASCII characters Name of the popup group Example SEND _ COMMAND Panel APG Popup1 Group1 Adds the popup page Popup1 to the popup group Group1 CPG Syntax Clear all popup CPG lt popup group name gt pages from Variable specified popup group popup group name 1 50 ASCII characters Name of the popup group Example SEND_COMMAND Panel CPG Group1 Clears all popup pages from the popup group G
169. pgrade the panel flash file system may become corrupted System Settings USBI Settings y Master Gonmnection FIG 25 System Settings page NOTE Panel downloads and firmware updates The MVP 5100 and MVP 5150 devices support a USB driver for panel downloads and firmware updates This means that the devices connect to a host computer for updates through their Mini USB ports FIG 26 All touch panel setup is done through NetLinx Studio and TPDesign4 Mini USB Port FIG 26 USB Port on the MVP 5100 5150 Firmware downloads require use of the USB Programming Cable FG10 5965 and a computer running Windows XP Touch panel setup To prepare the device for USB communication 1 Turn on the device and wait for it to finish booting up 2 Make sure that you have downloaded the latest versions of NetLinx Studio and TPDesign4 available from www amx com 3 Insert the mini USB end of the USB Programming Cable into the mini USB port on the device Insert the other end into the appropriate USB port on the computer containing the files to be downloaded 4 Ifthe connection goes well the Windows XP machine will detect the device as an unsupported USB device It then presents a dialogue box that prompts the user for a suitable driver FIG 27 Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking on your computer on the hardware installation CD or on
170. ponds to the local computer s Ethernet address Navigate to the Add IP Address field bottom right of the interface and enter the IP Addresses of the various target touch panels Click the Add button to complete the entry and add the new IP Address to the listing of available device IP Addresses Repeat this process for all subsequent device IP Addresses Once the list is complete click on the File drop down menu and select the Save option This launches a Save dialog to assign a name to the current list of addresses and then save the information as a TXT text file to a known location This application must be run from a local machine and should not be used from a remote network location 12 13 Select the target devices to be uploaded with the selected certificate These may be individually selected by toggling the box next to the Send entry with the Type column e selected as a group by clicking on the Check All radio box located at the top of the device IP Address listing When ready to send the certificate file to the selected panels click the Send button to initiate the upload Once the Status field for each entry reads Done the upload was successfully completed Appendix C Troubleshooting This section describes the solutions to possible hardware firmware issues that could arise during the common operation of a Modero touch panel Panel Doesn t Respond To Touches Symptom When calibrating the device the d
171. pplication Embedded codes The following is a list of G4 compatible embedded codes Embedded Codes Decimal numbers Hexidecimal values Virtual keystroke 8 08 Backspace 13 0D Enter 27 1B ESC 128 80 CTRL key down 129 81 ALT key down 130 82 Shift key down 131 83 F1 132 84 F2 133 85 F3 134 86 F4 135 87 F5 136 88 F6 137 89 F7 138 8A F8 139 8B F9 140 8C F10 141 8D F11 142 8E F12 143 8F Num Lock 144 90 Caps Lock 145 91 Insert 146 92 Delete 147 93 Home 148 94 End 149 95 Page Up 150 96 Page Down 151 97 Scroll Lock 152 98 Pause 153 99 Break 154 9A Print Screen 155 9B SYSRQ 156 9C Tab 157 9D Windows 158 9E Menu 159 9F Up Arrow 160 A0 Down Arrow 161 A1 Left Arrow 162 A2 Right Arrow 192 C0 CTRL key up 193 C1 ALT key up 194 C2 Shift key up rs LON cm la Panel Setup Commands These commands are case insensitive Panel Setup Commands AMUT Syntax Set the panel MUT lt mute state gt mute state Variable mute state 0 Mute Off and 1 Mute On Example SEND_COMMAND Panel MUT 1 Sets the panel s master volume to mute PWD PWD sets the level 1 password only Set the page flip Syntax password PWD lt page flip password
172. prompt text Enter State AKEYB Keyboard string is set to null on power up and is stored until power is lost Pop up the Syntax AKEYB lt initial text gt Variables keypad icon and initialize the text string to that specified initial text 1 50 ASCII characters Example SEND COMMAND Panel AKEYB This is a Test Pops up the Keyboard and initializes the text string This is a Test AKEYP The keypad string is set to null on power up and is stored until power is lost Pop up the Syntax AKEYP lt number string gt Variables specified number string 0 9999 Example SEND COMMAND Panel AKEP 12345 Pops up the Keypad and initializes the text string 12345 AKEYR Remove keyboard or keypad that was displayed using AKEYB AKEYP PKEYP Remove the AKB AKP PKP EKP or TKP commands Keyboard Syntax Keypad 1 AKEYR Example SEND COMMAND Panel AKEYR Removes the Keyboard Keypad ee a Panel Runtime Operation Commands Cont AKP Pop up the keypad icon and initialize the text string to that Keypad string is set to null on power up and is stored until power is lost The Prompt Text is optional Syntax AKP lt initial text gt lt prompt text gt specified Variables initial text 1 50 ASCII characters prompt text 1 50 ASCII characters Example SEND COMMAND Panel AKP 12345678 ENTER PASSWORD Pops up the Keypad and initiali
173. r Configuration Settings lt No Active System Default Settings gt System H lt Terminal Settings gt lt No Active System Default Settings gt Configuration Communication Settings OK Cancel FIG 69 Master Communications Settings dialog box 10 Click the Communications Settings button to open the Communications Settings dialog box FIG 70 Communication Settings Platform Selection Transport Connection Option NetLing Master TCPAP Edit Settings Axcess Master Serial Coden Authentication Required C Virtual NetLing Master FIG 70 Communications Settings dialog box 11 Click on the NetLinx Master radio button from the Platform Selection section 12 Click on the Virtual Master radio box from the Transport Connection Option section to configure the PC to communicate directly with a panel Everything else such as the Authentication is greyed out because this connection is not going through the Master s UI 13 Click the Edit Settings button on the Communications Settings dialog to open the Virtual NetLinx Master Settings dialog FIG 71 Virtual NetLinx Master Settings Master System Number 1 The Virtual NetLinx Master connection allows G4 devices to a directly connect to NetLinx Studio instead of a physical NetLinx Current Connection 10 0 0 1 Master for transfers Available Connections IP Address 192 168 224 135 Broadcom NetXtreme Gigabit Ethernet Packet Scheduler Minipa
174. r Supply FG423 30 both 120 VAC and 240 VAC models are shipped with this power supply Power Modes AWAKE All necessary modules are powered up and device remains online with the Netlinx Master ASLEEP Only the backlight will be turned off after the user selectable time of inactivity has elapsed Panel resumes the Awake mode in 1 second upon a momentary press of the touchscreen PROCESSOR SHUTDOWN Power to all peripherals and components is turned off The system remains in this mode until it is rebooted The panel is re activated by pressing the touchscreen and holding until the AMX splash screen appears Certifications FCC Part 15 Class B e CE IEC EN 60950 RoHS Japan Approved Lithium polymer microbattery UN IATA Battery Duration Memory 2 5 days of normal use in a combination of Awake and Shutdown Modes Three hours of continuous use continuous Awake state 128 MB Mobile DDRAM upgrade not available 256 MB NAND Flash upgrade not available Panel LCD Parameters Screen resolution 800 x 480 pixels HV 60 Hz frame frequency Type WVGA Aspect ratio 16 x 9 Brightness luminance 300 cd m Channel transparency 8 bit Alpha blending Contrast ratio 400 1 Display colors 262 144 colors 18 bit color depth Dot pixel pitch 0 23 mm Panel type TFT Color Active Matrix Screen resolution 800 x 480 pixels HV 60 Hz frame frequency Viewing angles Vertical 40 u
175. ral buttons 1 Off state and 2 On state unicode text 1 50 ASCII characters Unicode characters must be entered in Hex format Example SEND_COMMAND Panel BAU 520 1 00770062 Appends Unicode text 00770062 to the button s OFF state ABCB Only if the specified border color is not the same as the current color Set the border Note Color can be assigned by color name without spaces number or R G B value color to the RRGGBB or RRGGBBAA specified color Syntax BCB lt vt addr range gt lt button states range gt lt color value gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state color value Refer to the RGB Values for all 88 Basic Colors table on page 105 for more information Example SEND_COMMAND Panel BCB 500 504 amp 510 1 12 Sets the Off state border color to 12 Yellow Colors can be set by Color Numbers Color name R G B alpha colors RRGGBBAA and R G amp B colors values RRGGBB Refer to the RGB Values for all 88 Basic Colors table on page 105 ABCF Only if the specified fill color is not the same as the current color Set the fill color to Note Color can be assigned by color name without spaces number or R G B value the specified RRGGBB or RRGGBBAA color Syntax BCF lt vt addr range gt lt button states range gt lt color value gt
176. reless security method to be used by the panel to connect to the network Selecting any of the connection method buttons invokes the relevant configuration page with options that allow you to define parameters specific to the selected method of connection Open Clear Text This button opens the Open Clear Text Settings page FIG 56 on page 65 Open security does not utilize any encryption methodology but requires an SSID alpha numeric entry This entry must match the Network Name SSID entry of the target WAP so the panel knows what device it is using to communicate with the network Refer to the Open Clear Text Settings section on page 65 for further details Static WEP This button opens the Static WEP Settings page FIG 57 on page 66 Static WEP security requires that both a target WAP be identified and an encryption method be implemented prior to establishing communication e Refer to the Static WEP Settings section on page 66 for further details WPA PSK This button opens the WPA PSK Settings page FIG 58 on page 68 WPA PSK security is designed for environments where is it desirable to use WPA or WPA2 but an 802 1x authentication server is not available PSK connections are more secure than WEP and are simpler to configure since they implement dynamic keys but share a key between the WAP and the panel client Refer to the WPA PSK Settings section on page 67 for further details EAP PEAP
177. remote network location NOTE This application ensures that a unique certificate is securely uploaded to a specific touch panel Currently the target panels must be capable of supporting the WPA PSK and EAP XXX wireless security formats The Certificate Upload utility supports the following capabilities e Ability to browse both a local and network drive to find a desired certificate file e Ability to create a list of target AMX G4 touch panels based on IP Addresses e Ability to display the IP Address of the local computer hosting the application e Ability to load a previously created list of target touch panels e Ability to save the current list of target Modero panel as a file e Ability to track the progress of the certificate upload by noting the current data size being transmitted and any associated error messages if any The Certificate Upload Utility recognizes the following certificate file types CER Certificate File e DER Distinguished Encoding Rules e PEM Privacy Enhanced Mail e PFX Normal Windows generated certificate e PVK Private Key file How to Upload a Certificate File The mini USB connector MUST be then plugged into an already active panel before the PC can recognize the connection and assign an appropriate USB driver This driver is part of both the NetLinx Studio and TPDesign4 software application NOTE installations 1 Install the latest AMX USB LAN LINK driver onto your computer by installing th
178. ress range 1 4000 command value 0 disable 1 enable Example SEND_COMMAND Panel ENA 500 504 amp 510 515 0 Disables button pushes on buttons with variable text range 500 504 amp 510 515 NOTE A Button Commands Cont FON Set a font to a specific Font ID value for those buttons with a defined address range Font ID numbers are generated by the TPDesign4 programmers report Syntax FON lt vt addr range gt lt button states range gt lt font value gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state font value range 1 XXX Refer to the Default Font Styles and ID Numbers section on page 107 Example SEND_COMMAND Panel FON 500 504 amp 510 515 1 amp 2 4 Sets the font size to font ID 4 for the On and Off states of buttons with the variable text range of 500 504 amp 510 515 The Font ID is generated by TPD4 and is located in TPD4 through the Main menu Panel gt Generate Programmer s Report gt Text Only Format gt Readme txt A Button Commands Cont axis to move the origin to another corner GDI Syntax Change the GDI lt vt addr range gt lt bargraph drag increment gt bargraph drag Variable increment variable text address range 1 4000 bargraph drag increment The default drag increment is 256 Example SEND_
179. rget WAP or another Modero panel within the WEP Keys section touch the Key button to launch the WEP Key keyboard enter the characters and press Done when finished e This Key value corresponds to the Default WEP Key number used on the Wireless Access Point and selected in the Default Key field 11 The remaining Current Key field is greyed out and cannot be altered by the user The Authentication button can be toggled between Open and Shared ce NOTE 12 13 14 Verify that the fields within the JP Settings section have been properly configured Refer to Step 1 Configure the Device s Wireless IP Settings MVP 5150 Only section on page 23 for detailed information Press the Back button to navigate to the Protected Setup page and press the on screen Reboot button to save any changes and restart the panel Remember that you will need to navigate to the System Settings page and configure the connection to a target Master After the panel restarts return to the Wireless Settings page to verify the Link Quality and Signal Strength The descriptions are None Poor Fair Good Very Good and Excellent The signal strength field provides some descriptive text regarding the strength of the connection to a Wireless Access Point Configuration of the network could be required if there is no signal or no IP Address is displayed Configuring multiple wireless touch panels to communicate to a target WAP 1 For each com
180. ries page on the MVP to see any charging activity on the bar graphs The Sensor device in the Online Tree tab below the MVP panel should show v1 24 or higher after the upgrade as shown in FIG 92 JE 10009 MVP 8400 AMX Corp v2 55 43 Jy OlD 2 Kernel AMX Corp 2 4 20 59 01D 3 Root File System AMX Corp v0 03 17 i OlD 4 Bootrom AMX Corp None JE Oa Sensor AMX Corp v1 24 01D 6 Opt File System AMX Corp v0 02 17 gg OID 7 Battery Base AMX Corp 2 03 01D 8 Fpga AMX Corp v7 00 1 FIG 92 Sensor device in the Online Tree tab 2 NOTE Device Isn t Appearing In The Online Tree Tab 1 Verify that the System number is the same on both the NetLinx Project Navigator window and the System Settings page on the device 2 Verify the proper NetLinx Master IP and connection methods entered into the Master Connection section of the System Settings page Device Can t Obtain a DHCP Address In requesting a DHCP Address the DHCP Server can take up to a few minutes to provide the address 1 Verify that the WAP is configured to match the MVP panel Network Name SSID field Encryption Default Key and Current Key string In NetLinx Studio select Diagnostics gt Network Address and verify the System number 3 Ifthe JP Address field is still empty give the device a few minutes to negotiate a DHCP Address and try again My WEP Doesn t Seem To
181. rivacy Enhanced Mail e DER Distinguished Encoding Rules PKCS12 Public Key Cryptography Standard 12 PKCS12 files are frequently generated by Microsoft certificate applications Otherwise PEM is more common Certificate files frequently use 5 file extensions It can be confusing because there is not a one to one correspondence The following table shows the possible file extension used for each certificate type Certificates and their Extensions Certificate Type Possible File Extensions PEM cer pem pvk DER cer der PKCS12 pfx Please note which certificate types are supported by the different certificate fields used on the configuration screens PEAP TTLS and TLS The following table outlines the firmware fields and their supported certificate types Certificate Types Supported by the Modero Firmware Configuration Field Name Certificate File Type Supported Certificate Authority field PEM and DER Client Certificate field PEM and DER Private Key field PEM DER and PKCS12 Calibration Page The Calibration page FIG 66 allows you to calibrate the touch panel for accurate button selection JELE Touch each target in turn to calibrate FIG 66 Calibration page Press and hold the reset button for 6 seconds to access the Calibration page see FIG 48 2 Press the crosshairs in turn If the crosshairs are not touched within ten seconds the MVP 5100 will return
182. ro Text Blank Text length Zero Example SEND COMMAND Panel BOP 529 1 Gets the button OFF state opacity information The result sent to the Master would be ButtonGet Id 529 Type 1015 Flag 0 VALUE1 1 VALUE2 200 VALUE3 0 TEXT TEXT LENGTH 0 Button Query Commands Cont BRD Syntax Get the current BRD lt vt addr range gt lt button states range gt border name Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1014 Flag Zero Value1 Button state number Value2 Actual length of string Value3 Zero Text String that represents border name Text length Border name length Example SEND COMMAND Panel BRD 529 1 Gets the button OFF state border information The result sent to the Master would be ButtonGet Id 529 Type 1014 Flag 0 VALUE1 1 VALUE2 22 VALUE3 0 TEXT Double Bevel Raised L TEXT LENGTH 22 2BWW Syntax Get the current 2BWW lt vt addr range gt lt button states range gt word wrap flag Variable status variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1010 Flag Zero Value1 Button state number Value2 0 no word wrap 1 word wrap
183. roperties AMX supports the following security certificates within three different formats PEM Privacy Enhanced Mail DER Distinguished Encoding Rules PKCS12 Public Key Cryptography Standard 12 e Typical certificate information can include the following items Certificate Issue Date Extensions Issuer Public Key Serial Number Signature Algorithm User Version e MIC e Short for Message Integrity Check this prevents forged packets from being sent Through WEP it was possible to alter a packet whose content was known even if it had not been decrypted e TKIP e Short for Temporal Key Integration this is part of the IEEE 802 111 encryption standard for wireless LANs TKIP provides a per packet key mixing message integrity check and re keying mechanism thus ensuring that every data packet is sent with its own unique encryption key Key mixing increases the complexity of decoding the keys by giving the hacker much less data that has been encrypted using any one key E A e WEP e Short for Wired Equivalent Privacy WEP is a scheme used to secure wireless networks Wi Fi A wireless network broadcasts messages using radio which are particularly susceptible to hacker attacks WEP was intended to provide the confidentiality and security comparable to that of a traditional wired network As a result of identified weaknesses in this scheme WEP was superseded by Wi Fi Protected Access WPA and then by the f
184. roup1 DPG Syntax Delete a specific DPG lt popup page name gt lt popup group name gt popup page from specified popup group if it exists Variable popup page name 1 50 ASCII characters Name of the popup page popup group name 1 50 ASCII characters Name of the popup group Example SEND COMMAND Panel DPG Popup1 Group1 Deletes the popup page Popup1 from the popup group Group1 Page Commands Cont PDR Set the popup location reset flag If the flag is set the popup will return to its default location on show instead of its last drag location Syntax PDR lt popup page name gt lt reset flag gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On reset flag 1 Enable reset flag 0 Disable reset flag Example SEND COMMAND Panel PDR Popup1 1 Popup1 will return to its default location when turned On PHE Set the hide effect for the specified popup page to the named hide effect Syntax PHE lt popup page name gt lt hide effect name gt Variable popup page name 1 50 ASCII characters Name of the page the popup is displayed On hide effect name Refers to the popup effect names being used Example SEND_COMMAND Panel PHE Popup1 Slide to Left Sets the Popup1 hide effect name to Slide to Left PHP Set the hide effect position Only 1 coordinate is ever nee
185. rs on the icon if the panel is connected to a secured NetLinx Master File Name Displays the name of the TPDesign4 project file downloaded to the panel Designer ID Displays the designer information File Revision Displays the revision number of the file Dealer ID Displays the dealer ID number unique to every dealer and entered in TPD4 Job Name Displays the job name CN ella Project Information Page Cont Sales Order Displays the sales order information Purchase Order Displays the purchase order information AMX IR 38K Assigned Displays the AMX 38 kHz IR channel port used by the IR Emitter on the panel Port e This information is specified in TPD4 Project Properties gt IR Emitters amp Receivers tab e For example if you set the AMX IR 38K Port to 7 and then put a button on the panel with a channel code of 5 and a port of 7 it will trigger the IR code in slot 5 of the AMX IR 38K Port IR User Defi Port Displays the primary channel port used by the IR receiver on the panel IR User Def2 Port Displays the secondary channel port used by the IR receiver on the panel Build Number Displays the build number information of the TPD4 software used to create the project file Creation Date Displays the project creation date Revision Date Displays the last revision date for the project Last Save Date Displays the last date the project was saved Blink Rate
186. rt OK Cancel FIG 71 Virtual NetLinx Master Settings dialog box 14 Within this dialog enter the Master System number The default is 1 15 In the Available Connections section click on the IP address for the touch panel to select it 16 In the Virtual NetLinx Master Settings dialog box click OK to close the box 17 In the Communications Settings dialog box click OK to close the box 18 In the Master Communications Settings dialog box click OK to save your settings and return to the main NetLinx Studio application 19 Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System The default System value is 1 20 Right click on the Empty Device Tree System entry and select Refresh System to re populate the list NOTE NOTE NOTE The panel will not appear as a device below the virtual system number in the Online Tree tab until both the system number used in step 14 for the Virtual NetLinx Master is entered into the Master Connection section of the System Settings page and the panel is restarted 21 The OnLine Tree should now display the connection to the device The Connection Status Icon on the device make take up to five seconds to register the connection Step 3 Confirm and Upgrade the firmware via the USB port Use the CC USB Type A to Mini B 5 wire programming cable to provide communication between the mini USB Program port on the touch panel and the PC This method of communi
187. s an on screen keyboard to enter the SSID name used on the target WAP The SSID is a unique name used by the WAP and is assigned to all panels on that network An SSID is required by the WAP before the panel is permitted to join the network e The SSID is case sensitive and must not exceed 32 characters e Make sure this setting is the same for all points in your wireless network e NXA WAP250Gs use AMX as their default SSID e If this field is left blank the panel will attempt to connect to the first available WAP Password Pass Phrase Opens an on screen keyboard to enter a passphrase password e This alpha numeric string must use a minimum of 8 characters and a maximum of 63 e The exact pass phrase string including capitalization must be entered on the target WAP WPA PSK Settings Cont Save Cancel Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page Refer to the Configuring Wireless Network Access MVP 5150 Only section on page 23 for details on these security options Refer to the Using the Site Survey tool section on page 26 for more information on using this tool EAP Security amp Server Certificates Overview The following EAP types all support a server certificate e EAP PEAP e EAP TTLS e EAP TLS _ nn OL ee All three of these certificate using security methods are docum
188. s range 1 4000 max length 2000 0 no max length Example SEND_COMMAND Panel BML 500 20 Sets the maximum length of the text area input button to 20 characters BMP Assign a picture to those buttons with a defined address range Syntax BMP lt vt addr range gt lt button states range gt lt name of bitmap picture gt Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state name of bitmap picture 1 50 ASCII characters Example SEND_COMMAND Panel BMP 500 504 amp 510 515 1 bitmap png Sets the OFF state picture for the buttons with variable text ranges of 500 504 amp 510 515 ABNC Clear current TakeNote annotations Syntax t BNC lt vt addr range gt lt command value gt Variable variable text address range 1 4000 command value 0 clear 1 clear all Example SEND_COMMAND Panel BNC 973 0 Clears the annotation of the TakeNote button with variable text 973 A Button Commands Cont BNN Set the TakeNote network name for the specified Syntax BNN lt vt addr range gt lt network name gt Variable variable text address range 1 4000 Addresses network name Use a valid IP Address Example SEND_COMMAND Panel BNN 973 192 168 169 99 Sets the TakeNote button network name to 192 168 169
189. s together and is used in most LAN local area networks This description is also used to refer to both wired and wireless communication A Wireless Ethernet connection involves indirect communication from the panel to a Master via a wireless connection to the network e A USB connection is a direct connection from the panel s mini USB port to a corresponding USB port on the PC acting as a Virtual Master System Setting Page Elements Cont Mode Cycles between the connection modes URL Listen NDP UDP URL UDP and Auto Ethernet Only disabled when USB is selected URL In this mode enter the IP URL Master Port Number and username password if used on the Master The System Number field is read only the panel obtains this information from the Master e Listen In this mode add the panel address into the URL List in NetLinx Studio and set the connection mode to Listen This mode allows the Modero touch panel to listen for the Master s communication signals The System Number and Master IP URL fields are read only NDP UDP In this mode The System Number and Master IP URL fields are read only e URL UDP In this mode The System Number and Master IP URL fields are read only e Auto In this mode enter the System Number and a username password if applicable Use this mode when both the panel and the NetLinx Master are on the same Subnet and the Master has its UDP feature enabled The Ma
190. se security options EAP TTLS Settings Press the EAP TTLS button to open the EAP TTLS Settings page FIG 64 EAP Tis SSID Identity Anony moug Identity Aathonty Innen Authentication EAP MSCHAPv2 Type Save Cancel FIG 64 Wireless Settings page EAP TTLS Settings TTLS EAP Tunneled Transport Layer Security is an authentication method that does not use a client certificate to authenticate the panel However this method is more secure than PEAP because it does not broadcast the identity of the user Setup is similar to PEAP but differs in the following areas e An anonymous identity must be specified until the secure tunnel between the panel and the Radius server is setup to transfer the real identity of the user There is no end user ability to select from the different types of PEAP e Additional Inner Authentication choices are available to the end user EAP TTLS security is designed for wireless environments where the Radius server needs to validate directly the identity of the client panel before allowing it access to the network This validation is done by tunneling a connection through the WAP and directly between the panel and the Radius server Once the client is identified and then validated the Radius server disconnects the tunnel and allows the panel to access the network directly via the target WAP EAP TTLS Settings SSID Service Set Identifier Opens an on screen keyboard to e
191. sensccdscusnsncoscnsovessoadissaionnesoassaaseosesnesseds 151 Text Formatting Codes for Bargraphs JoystickS sseesseseessseseeeessseeeessseseessssseeeee 151 Text Area Input Maski ngis ssissssssissessssessisersoss cssseccsessnnsssnnubeusssesssvexssesuischaseondsneeessees 152 Input mask character types is5 s 0c02 chciceededs cansesesecceppiceceedsstexeedsedosccepboccececseesenevssoebecnnes 152 Input mask ranges sssi sicoiir esi saniki ans aisant eeni Side Nees E 153 Input mask next field characters scccccsssssescssssseeccsessssseeessssssseccessssseeeesesssseeeeosees 153 Input Mask OPEratiONs cce o ci assescececccteeecececetexsavsescecenp rsu eere e suveedosdensboececeeesexsevceseedesstas 153 Input mask literals lcccceteccsecccesccdeedceceetessceveivesetagsetececcesdecesvecesouaevetesceetesestvdevesuesreses 153 LO Input mask output examplesi c csscecseecesecccesiencessveoessssoeeesctoccder eosssestseseossecessentecstess 154 URL RESOURCES casei ccsscscesucsanissdervnsesinnins cosessuauennscnsecesidionssdseneudsebooduneseveiubenaesussnvesevees 155 Special Escape SCQUENCES ii sscsesccds ice ccesesscevsesseaccccenibdceseeecsn sedecodets EKE NEONET Err EEEE Eae 155 Appendix B Wireless Technology ssssssiarasriasiisspisasssssiaronadnivassiannsnesiseanssassannrns 156 Overview of Wireless Technology ssssesssssssececcceecsseesssssssessceeeeeesesesssssssseees 156 TPE OIO GY ono codes vse concise acca cles bs N 157 EAP
192. sesossriseissvosessss nosines unser E sins N ENESTE KONE EK SKEE s ese KiKa eis 7 Powering the MVP TCS 52 scsi ccsccscescccccseecevescssseectesSececceesesavessseseusesosdeceresvessvessveoesesosseeee 8 Connections and WIRING 2 scccccsssccesscctctecccscdcevectesestecesedseccesoseteceasseveveveueeccssocedeceesestavebeveecs 8 RECHARGING secsecssitsstkecokects catecetes e aE en o E Ea EE EE 8 Cleaning the MVP 1CS 52 ooicciccccisseiescssctccegsccecennscassvsestovecnesediseeteresessessouporns seesesesrsvessseses 8 Wall Charging Station ssiccccsiccccccsscscticsccoctccssccecvasencspetibeenssistsedessensssebiocetsoesnssdeeantessebee 9 Unlocking the touch Panel seb ai esashde stk sco sexcahachecatsckststvavectenmersdencecuseaewecvsteienenennessties 10 RECHARGING A E EE E 11 Installing the MVP WCS 52 cass cscwiscvccesseseseansasnncnagetaxconndeadecsunabondpsenseendnenseseenenesnseies 12 Installing the plastic B ck Box s0sccccsssessseseseesstssececesseusucvoseseecteccosecdescuedtessoseeseosees 12 Installing the Optional Metal Rough In Box ccccccccesesssesssssssssssesceecesesesesssssssseeeees 16 Other MVP WCS 52 installations ssssssssssssssssssssesssesccecceseeeessccccescceecesseesseeseeeeees 17 Contiguring Communication nssicussasiwersvonrarinmutmanaunaeinrsipnmancanamuciiens 19 IR Communicati des sanssiotesastscanchetscucnsienns okxesdeneskoisadeussansterstdsmceetssieaneancustiiaraaenenstand 20 Modero Setup and System Settings
193. specified Keypad displays a Present a private keypad instead of the numbers typed The Prompt Text is optional Syntax PKEYP lt initial text gt Variables initial text 1 50 ASCII characters Example SEND COMMAND Panel PKEYP 123456789 Pops up the Keypad and initializes the text string 123456789 in PKP Present a private keypad Pops up the keypad icon and initializes the text string to that specified Keypad displays a instead of the numbers typed The Prompt Text is optional Syntax PKP lt initial text gt lt prompt text gt Variables initial text 1 50 ASCII characters prompt text 1 50 ASCII characters Example SEND COMMAND Panel PKP 1234567 ENTER PASSWORD Pops up the Keypad and initializes the text string ENTER PASSWORD in SETUP Syntax Send panel to SETUP SETUP page Example SEND COMMAND Panel SETUP Sends the panel to the Setup Page SHUTDOWN Syntax Shut down the 1 SHUTDOWN batteries providing Example power to the SEND COMMAND Panel SHUTDOWN anel i Shuts down the batteries feeding power to the panel This function saves the battery from discharging SLEEP Syntax Force the panel I SLEEP into screen saver Example mode SEND COMMAND Panel SLEEP Forces the panel into screen saver mode Panel Runtime Operation Commands Cont SOU Play a sound file Syntax SOU lt sound name gt
194. stem Connection icon does not turn green check the USB connection and communication settings and refresh the system Connecting to the NetLinx Master via Ethernet MVP 5150 Only 1 When using Wireless Ethernet with the MVP 5150 press the listed Mode to toggle through the available connection modes Connection Modes Mode Description Procedures None No connection None Auto The device connects to the first master that Setting the System Number responds This setting requires setting the 1 Select the System Number to open the keypad System Number 2 Set your System Number and select Done URL The device connects to the specific IP of a Setting the Master IP Master via a TCP connection This setting 1 Select the Master P number to the keyboard requires setting the Master s IP 2 Set the Master IP and select Done Listen The device listens for the Master to initiate Confirm that the device IP is on the Master URL contact This setting requires providing the list Set the Host Name on the device and use it to Master with the device s IP locate the device on the Master Host Name is particularly useful in the DHCP scenario where the IP address can change 2 Select the Master Port Number to open the keypad and change this value The default setting for the port is 1319 een CON ala Set the Master Port and select Done If you enabled password security on your Master set t
195. ster IP URL field is read only System Number Allows entry of a system number Default value is 0 zero ETHERNET in Auto Mode Only disabled when USB is selected Master IP URL Sets the Master IP or URL of the NetLinx Master ETHERNET in URL and URL UDP Modes Only disabled when USB is selected Master Port Number Allows entry of the port number used with the NetLinx Master Default 1319 ETHERNET Only disabled when USB is selected Username Password If the target Master has been previously secured enter the alpha numeric string into each field assigned to a pre configured user profile on the Master This profile should have the pre defined level of access configuration rights NDP Name Displays the name of the device connecting to the Master Refer to the Step 3 Choose a Master Connection Mode section on page 33 for more detailed information on using the System Settings page Wireless Settings Page MVP 5150 Only Use the options on the Wireless Settings page FIG 54 to configure communication settings for the wireless CF card 802 11b g and read the device number assigned to the panel Since the MVP 5100 does not have wireless capability the button to this page is greyed out in the MVP 5100 Protected Settings page Wireless Settings IP Settings Uira Setetinity DHCP Static Ce SC Open Clear Text EAP TTLS adie Se PT HostName WPA PSK P EAP LEAP EAP PEAP EAP FAST
196. t be set before selecting Ethernet as the Master Connection Type The Wireless Access Point communication parameters must match those of the pre installed wireless CF card inside the device MVP touch panels connect to a wireless network through their use of the pre installed AMX 802 11 wireless interface card This allows users to communicate with a Wireless Access Point WAP The WAP communication parameters must match those of the pre installed wireless interface card installed within the panel This internal card transmits data using 802 11x signals at 2 4 GHz For a more detailed explanation of the new security and encryption technology refer to the Appendix B Wireless Technology section on page 156 For more information on utilizing the AMX Certificate Upload Utility in conjunction with the EAP security refer to the AMX Certificate Upload Utility section on page 162 Configuring Wireless Network Access MVP 5150 Only The first step in connecting the MVP 5150 to a wireless network is to configure the wireless communication parameters within the device s Wireless Settings page This page only configures the card to communicate to a target WAP the device must still be directed to communicate with the correct Master This pointing to a Master is done via the System Settings page which allows configuration of the IP Address System Number and Username Password information assigned to the target Master Step 1 Configure the Device s
197. table value e Example 1 If you type 125 into a field accepting 0 100 then the values displayed will be 1 12 25 e Example 2 If the max for the field was 20 then the values displayed will benp 128 5 When data overflows from a numerical field the overflow value is added to the previous field on the chain if the overflow character was specified In the above example if the overflow flag was set the first example will place the 1 into the previous logical field and the second example will place 12 in the previous logical field If the overflow field already contains a value the new value will be inserted to the right of the current characters and the overflow field will be evaluated Overflow continues to work until a field with no overflow value is set or no more fields remain i e reached first field If a character is typed and that character appears in the Next Field list the keyboard should move the focus to the next field For example when entering time a is used as a next field character If you enter 1 2 the 1 is entered in the current field hours and then the focus is moved to the next field and 2 is entered in that field When entering time in a 12 hour format entry of AM and PM is required Instead of adding AM PM to the input mask specification the AM PM should be handled within the NetLinx code This allows a programmer to show hide and provide discrete feedback for AM and PM Input mask output e
198. tailed information e BIM Sets the input mask for the specified addresses see the B M section on page 114 BMF subcommand MK sets the input mask of a text area see the BMF section on page 116 Input mask ranges These ranges allow a user to specify the minimum and maximum numeric value for a field Only one range is allowed per field Using a range implies a numeric entry ONLY Input Mask Ranges Character Meaning Start range End range Range Separator An example from the above table 01255 This allows a user to enter a value from 0 to 255 Input mask next field characters These characters allow you to specify a list of characters that cause the keyboard to move the focus to the next field when pressed instead of inserting the text into the text area Input Mask Next Field Char Character Meaning Start Next Field List End Next Field List An example from the above table or or Proceed to the next text area input box after a user hits any of these keys Input mask operations Input Mask Operators change the behavior of the field in the following way Input Mask Operators Character Meaning lt Forces all characters to be converted to lowercase gt Forces all characters to be converted to uppercase Sets the overflow flag for this field Input mask literals To define a literal character enter any chara
199. tate text effect color information The result sent to the Master would be ButtonGet Id 529 Type 1009 Flag 0 VALUE1 1 VALUE2 9 VALUE3 0 TEXT 5088F2AE TEXT LENGTH 9 Button Query Commands Cont TEF Syntax Get the current TEF lt vt addr range gt lt button states range gt text effect name Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1008 Flag Zero Value1 Button state number Value2 Actual length of string Value3 Zero Text String that represents the text effect name Text length Text effect name length Example SEND COMMAND Panel TEF 529 1 Gets the button OFF state text effect name information The result sent to the Master would be ButtonGet Id 529 Type 1008 Flag 0 VALUE1 1 VALUE2 18 VALUE3 0 TEXT Hard Drop Shadow 3 TEXT LENGTH 18 2TXT Syntax Get the current TXT lt vt addr range gt lt button states range gt lt optional index gt text information Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state optional index This is used if a string was too long to get back in one command The reply will start at this index custom event type 1001 Flag
200. the Configuring Wireless Network Access MVP 5150 Only section on page 23 and the Using the Site Survey tool section on page 26 for further details on these security options WPA PSK Settings Press the WPA PSK button to opens the WPA PSK dialog FIG 58 WPA PSK security is designed for environments where using WPA or WPA2 is desirable but an 802 1x authentication server is not available PSK connections are more secure than WEP and are simpler to configure since they implement dynamic keys but share a key between the WAP and the panel client Using WPA PSK the encryption on the WAP could either be WPA or WPA2 The firmware in the panel will automatically connect to the WAP using the correct encryption The WPA encryption type is configured on the WAP not in the firmware WAPs do not display WPA or WPA on their configuration screens WPA is normally displayed as TKIP e WPA2 is normally displayed as AES CCMP The following fields are required SSID and Password Pass Phrase e Enter the SSID of the WAP i a 4 WERATBSK SSIB Se Phrase Error Password must be between 8 and 63 characters in length ae SEW ie ae Cancel FIG 58 Wireless Settings page WPA PSK Settings e Enter a pass phrase with a minimum of 8 characters and a maximum of 63 e The exact same pass phrase including capitalization must be entered in the access point WPA PSK Settings SSID Service Set Identifier Open
201. tificate file No file path should be used for this setting as all certificates are stored in a specific directory that the user cannot control or change e Use the on screen keyboard s Clear button to completely erase any previously stored network path information Client Certificate Opens an on screen keyboard for entering the name of the file containing the client panel certificate for use in certifying the identity of the client panel e Refer to the Client certificate configuration section on page 80 for information regarding Client Certificates and their parameters Private Key When pressed the panel displays an on screen Client Private Key File Location keyboard for entering the name of the file containing the private key e Use the on screen keyboard s Clear button to completely erase any previously stored network path information Private Key password This field should only be used if the Private Key is protected with a password If no password protection is associated with the Private Key then this field should be left blank e When pressed the panel displays an on screen Private Key Password keyboard which allows you to enter an alpha numeric password string e Use the on screen keyboard s Clear button to completely erase any previously stored network path information Save Cancel e Save store the new security information apply changes and return to the previous page e Ca
202. tings will be able to communicate Similarly if one device has WEP enabled and another does no they will not be able to talk to each other Although the calculations required to encrypt data with WEP can impact the performance of your wireless network this impact is generally only seen when running benchmarks and is not large enough to be noticeable in the course of normal network usage Terminology e 802 1x e IEEE 802 1x is an IEEE standard that is built on the Internet standard EAP Extensible Authentication Protocol 802 1x is a standard for passing EAP messages over either a wired or wireless LAN Additionally 802 1x is also responsible for communicating the method with which WAPs and wireless users can share and change encryption keys This continuous key change helps resolve any major security vulnerabilities native to WEP e AES e Short for Advanced Encryption Standard is a cipher currently approved by the NSA to protect US Government documents classified as Top Secret The AES cipher is the first cipher protecting Top Secret information available to the general public e CERTIFICATES CA e A certificate can have many forms but at the most basic level a certificate is an identity combined with a public key and then signed by a certification authority The certificate authority CA is a trusted external third party which signs or validates the certificate When a certificate has been signed it gains some cryptographic p
203. tion is not guaranteed because the detected WAP may be connected to a RADIUS server which may not support this EAP type and or have the proper user identities configured Identity Opens an on screen keyboard to enter an EAP Identity string used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to a username used to login to a secured server or workstation This works in tandem with the Password string which is similar to the password entered to gain access to a secured workstation Typically this is in the form of a username such as jdoe amx com EAP FAST Settings Cont Anonymous Identity Opens an on screen keyboard to enter an IT provided alphanumeric string which similar to the username is used as the identity but that does not represent a real user This information is used as a fictitious name which might be seen by sniffer programs during the initial connection and setup process between the panel and the Radius server In this way the real identity username is protected Typically this is in the form of a fictitious username such as anonymous amx com Password Opens an on screen keyboard Enter the network password string specified for the user entered within the dentity field used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to the password entered to gain access to a secured wor
204. tivated This command works in the same way as the Hide Popup command in TPDesign4 Syntax PPF lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of the popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PPF Popup1 Main Example 2 SEND _COMMAND Panel PPF Popup1 Deactivates the popup page Popup1 on the current page PPG Toggle a specific popup page on either a specified page or the current page If the page name is empty the current page is used see example 2 Toggling refers to the activating deactivating On Off of a popup page This command works in the same way as the Toggle Popup command in TPDesign4 Syntax PPG lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of the popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PPG Popup1 Main Toggles the popup page Popup1 on the Main page from one state to another On Off Example 2 SEND _ COMMAND Panel PPG Popup1 Toggles the popup page Popup1 on the current page from one state to another On Off PPK Kill a specific popup page from all pages Kill refers to the deactivating Off of a popup window from all pages If the pop up page is part of a group th
205. to a target WAP 32 Step 3 Choose a Master Connection Mode cccsssescececececeecececeeeeeeceseeeeeeeeoes 33 Panel downloads and firmware UPCates ccccccsecssssssscseceeceeesessesscesssssseeeeeeees 34 To ch Pamell setup i sssscece ech et oee dads cvesevsseceecetteedessuccuvdeveecstecbbececcecesexveves svoadunudesececeeseeeueres 34 Configure a Virtual NetLinx Master via USB cccccssssscesscssssecesesssseeeesessssseeeeseseeees 38 Connecting to the NetLinx Master via Ethernet MVP 5150 Only cssseseeeeeeeeeee 40 Master Connection to a Virtual Master via Ethernet cccccssscsssssssssssssseceeesssseeees 41 Setup PAGES icc cssccicocsvsncctawssscsssnedssienenssicd ssesensessnioneonseceoensunusin bessannestseenessaeecseaens 45 Setup PAGES wissesecssnsindusseacnnncexenethaundnacndentsnaadaassensnschecendosntannacabeneteacsandanenotenecendnaensuee 45 Navigation Buttons ccccccssssssssssecssssessssssesscesceseeesssesseeseeeseeesuaeaeeseeesocsosesssssseseseeeeenes 47 Protected Setup Pages sisiscsisiesesscisercsceecsnesciueacousdcesendensspabesasncendinscecdeesnssansavedecsivense 47 Information BEE OM anc csc cteecenbstebect cxccescoceestunstendecbexwsueceressnivueieussewieeetivustndeestoteans 48 Project Information Pagesos resos aeneae aee KORE EOE REE AA aE E EISERES 48 Panel Information Page s ccsscsces ce ex ciscavesnscnasesesteicp seg eipatasescs ce ceucdigass czeeas te ceeodsoseensste
206. to the Protected Setup page 3 The page will read Calibration Successful Touch to continue Touch anywhere on the screen to return to the Protected Setup page If the screen is not touched at that point the device will automatically return to the Protected Setup page within 10 seconds NOTE Always calibrate the panel before its initial use and after downloading new firmware Other Settings Press the Other Settings button to display the two settings options for Cache and Password Press one of the options within three seconds or the two options buttons will slide back behind the Other Settings button Cache Settings Page The options on the Cache Settings page FIG 67 allow setting and clearing of the flash memory cache as well as viewing the status of the current cache settings Since image files take up a significant amount of the touch panel s flash memory being able to examine the current limits and contents is useful in deciding whether to increase or decrease the total flash cache size Cache Settings FIG 67 Cache Settings Page Cache Settings Page Back Saves all changes and returns to the previous page Connection Status icon The icon in the upper right corner of each Protected Setup page provides a constant visual indication of current connection status Note a Lock appears on the icon if the panel is connected to a secured NetLinx Master Image Cache Settings RAM Max Size The maximum size
207. tton OFF state border color information The result sent to the Master would be ButtonGet Id 529 Type 1011 Flag 0 VALUE1 1 VALUE2 9 VALUE3 0 TEXT 222222FF TEXT LENGTH 9 Button Query Commands Cont BCF Syntax Get the current fill BCF lt vt addr range gt lt button states range gt color Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1012 Flag Zero Value1 Button state number Value2 Actual length of string should be 9 Value3 Zero Text Hex encoded color value ex 000000FF Text length Color name length should be 9 Example SEND COMMAND Panel BCF 529 1 Gets the button OFF state fill color information The result sent to the Master would be ButtonGet Id 529 Type 1012 Flag 0 VALUE1 1 VALUE2 9 VALUE3 0 TEXT FF8000FF TEXT LENGTH 9 2BCT Syntax Get the current BCT lt vt addr range gt lt button states range gt text color Variable variable text address range 1 4000 button states range 1 256 for multi state buttons 0 All states for General buttons 1 Off state and 2 On state custom event type 1013 Flag Zero Value1 Button state number Value2 Actual length of string should be 9 Value3 Zero Text Hex encoded color value ex 000000FF Text
208. turned and exhibit signs of damage or unauthorized use will be processed under the Non Warranty Repair Policy AMX will continue to provide Warranty Repair Services for products discontinued or replaced by a Product Discontinuance Notice Non Warranty Repair Policy Products that do not qualify to be repaired under the Warranty Repair Policy due to age of the product or Condition of the prod uct may be repaired utilizing this service The AMX Authorized Partner must contact AMX Technical Support to validate the failure before pursuing this service Non warranty repair is a billable service Products repaired under this policy will carry a ninety 90 day warranty on material and labor AMX will notify the AMX Authorized Partner with the cost of repair if cost is greater than the Standard Repair Fee within five 5 days of receipt The AMX Authorized Partner must provide a Purchase Order or credit card number within five 5 days of notification or the product will be returned to the AMX Authorized Partner The AMX Authorized Partner will be responsible for in bound and out bound freight expenses Products will be repaired within ten 10 business days after AMX Authorized Partner approval is obtained Non repairable products will be returned to the AMX Authorized Partner with an explanation See AMX Non Warranty Repair Price List for minimum and Standard Repair Fees and policies FCC Information This device complies with Part 15 of th
209. ubstantially in accor dance with the accompanying written materials for a period of ninety 90 days from the date of receipt AMX DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH REGARD TO THE AMX SOFTWARE THIS LIM ITED WARRANTY GIVES LICENSEE SPECIFIC LEGAL RIGHTS Any supplements or updates to the AMX SOFTWARE including without limitation any if any service packs or hot fixes provided to Licensee after the expiration of the ninety 90 day Limited Warranty period are not covered by any warranty or condition express implied or statutory LICENSEE REMEDIES AMX s entire liability and Licensee s exclusive remedy shall be repair or replacement of the AMX Soft ware that does not meet AMX s Limited Warranty and which is returned to AMX in accordance with AMX s current return policy This Limited Warranty is void if failure of the AMX Software has resulted from accident abuse or misapplication Any replace ment AMX Software will be warranted for the remainder of the original warranty period or thirty 30 days whichever is longer Outside the United States these remedies may not available NO LIABILITY FOR CONSEQUENTIAL DAMAGES IN NO EVENT SHALL AMX BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIA
210. ull IEEE 802 111 standard also known as WPA2 e WPA e Wi Fi Protected Access WPA and WPA2 is a class of system used to secure wireless Wi Fi computer networks It was created in response to several serious weaknesses researchers had found in the previous WEP system WPA implements the majority of the IEEE 802 111 standard and was intended as an intermediate measure to take the place of WEP while 802 111 was prepared WPA2 WPA is designed to work with all wireless network interface cards but not necessarily with first generation wireless access points To resolve problems with WEP the Wi Fi Alliance released WPA FIG 89 which integrated 802 1x TKIP and MIC Within the WPA specifications the RC4 cipher engine was maintained from WEP RC4 is widely used in SSL Secure Socket Layer to protect internet traffic Wi Fi Protected Access WPA TKIP MIC RC4 802 1x z z Z al be 9 Authentication FIG 89 WPA Overview e WPA2 e Also know as IEEE 802 11i this is an amendment to the 802 11 standard specifying security mechanisms for wireless networks The 802 11i scheme makes use of the Advanced Encryption Standard AES block cipher WEP and WPA use the RC4 stream cipher The 802 111 architecture contains the following components 802 1X for authentication entailing the use of EAP and an authentication server RSN for keeping track of associations and AES based CCMP to provide confidentiality int
211. ut fields in the ZP Settings section cannot be altered Once the panel is rebooted these values are obtained by the unit and displayed in the DNS fields after power up This information can be found in either the Workspace System name gt Define Device section of the code that defines the properties for the panel or in the Device Addressing Network Addresses section of the Tools gt NetLinx Diagnostics dialog 6 Set up the security and communication parameters between the wireless card and the target WAP by configuring the Wireless Settings section on this page Refer to Step 2 Configure the Card s Wireless Security Settings section on page 27 for detailed procedures to setup either a secure or insecure connection NOTE Wireless communication using a Static IP Address 1 From the Protected Setup page press the Wireless Settings button to open the Wireless Settings page Wireless communication is set within the IP Settings section of this page FIG 15 Check with your System Administrator for a pre reserved Static IP Address to be assigned to the panel This address must be obtained before continuing with the Static assignment of the panel 2 Toggle the DHCP Static field from the IP Settings section until the choice cycles to Static The IP Address Subnet Mask and Gateway fields then turn red noting that they are now user editable Press the IP Address field to open a keyboard and enter the Static IP Address provide
212. value Example SEND_COMMAND Panel UNI 500 1 0041 Sets the button s unicode character to A Note To send the variable text A in unicode to all states of the variable text button 1 for which the character code is 0041 Hex send the following command SEND_COMMAND TP UNI 1 0 0041 Note Unicode is always represented in a HEX value TPD4 generates through the Text Enter Box dialog unicode HEX values Refer to the TPDesign4 Instruction Manual for more information Miscellaneous MVP Strings back to the Master The following two strings are sent by the MVP panel back to the communicating Master MVP Strings to Master undock lt master gt This is sent to the target Master when the MVP is undocked If the panel has no information within the User Access Passwords list none is sent as a user If the undock button on the Protected Setup page is used setup is sent as a user e This string can be disabled from within the firmware setup pages dock This is sent to the target Master when the MVP is docked e This string can be disabled from within the firmware setup pages MVP Panel Lock Passcode commands These commands are used to maintain a passcode list With the MVOP 5200i a password must be entered to remove the panel from the Wall Charging Station Only the passcode is entered The user entry is just for identifying the passcodes MVP Panel Lock Passcode Commands
213. ve and must not exceed 32 characters e Make sure this setting is the same for all points in the wireless network e NXA WAP250Gs use AMX as their default SSID e With EAP security the SSID of the WAP must be entered If it is left blank the panel will try to connect to the first access point detected that supports EAP However a successful connection is not guaranteed because the detected WAP may be connected to a RADIUS server which may not support this EAP type and or have the proper user identities configured Identity Password Opens an on screen keyboard Enter an EAP Identity string used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to a username used to login to a secured server or workstation This works in tandem with the Password string which is similar to the password entered to gain access to a secured workstation Typically this is in the form of a username such as jdoe amx com Opens an on screen keyboard Enter the network password string specified for the user entered within the dentity field used by the panel to identify itself to an Authentication RADIUS Server Note This information is similar to the password entered to gain access to a secured workstation Save Cancel e Save store the new security information apply changes and return to the previous page e Cancel discard changes and return to the previous page
214. will choose the driver to install Choose this option to select the device driver from a list Windows does not guarantee that the driver you choose will be the best match for your hardware emen FIG 28 Found New Hardware Wizard Installation Options dialogue box 8 Click on Next 9 The Windows XP machine now searches for the suitable driver FIG 29 Found New Hardware Wizard Please wait while the wizard searches nw Y oy RNDIS Ethemet Gadget FIG 29 Found New Hardware Wizard while searching for the driver 10 Once the system finds the driver it displays its choice FIG 30 Click Finish to complete the driver installation Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Eg Linux USB Ethemet ANDIS Gadget Click Finish to close the wizard Back Cancel FIG 30 Completing the Found New Hardware Wizard The USB interface will require a static IP address Proceed to the next steps to set up the IP address on the USB interface In Windows XP 1 From the Windows XP desktop click on Start gt Control Panel gt Network Connections gt Local Area Connection This opens a window listing the currently active network connections 2 Select the connection to the device name of AMX USB Device Link 3 Right click on the selected device and select Properties to open the Local Area Connection
215. works in the same way as the Hide Popup command in TPDesign4 Syntax PPOF lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of the popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND_COMMAND Panel PPOF Popup1 Main Deactivates the popup page Popup1 on the Main page Example 2 SEND _COMMAND Panel PPOF Popup1 Deactivates the popup page Popup1 on the current page PPOG Toggle a specific popup page on either a specified page or the current page If the page name is empty the current page is used see example 2 Toggling refers to the activating deactivating On Off of a popup page This command works in the same way as the Toggle Popup command in TPDesign4 Syntax PPOG lt popup page name gt lt page name gt Variable popup page name 1 50 ASCII characters Name of the popup page page name 1 50 ASCII characters Name of the page the popup is displayed On Example SEND COMMAND Panel PPOG Popup1 Main Toggles the popup page Popup1 on the Main page from one state to another On Off Example 2 SEND _ COMMAND Panel PPOG Popup1 Toggles the popup page Popup1 on the current page from one state to another On Off PPON Activate a specific popup page to launch on either a specified page or the current page If the page name is empty the curre
216. wsayP geting Wn Master Connection assigne to tho Master within the AMX software application these must match Enterthe IP Address information of the PC used as a Virtual Master When using a Virtual Master there is no needto enter a usemame and or password FIG 39 Sample System Settings page for Virtual Master communication 12 Press the blue Type field from the Master Connection section until the choice cycles to the word Ethernet 13 Press the Mode field until the choice cycles to the word Auto e By selecting Auto the URL field becomes read only grey because the panel pulls this value directly from the communicating target Master virtual or not A Virtual Master system value can be set within the active AMX software applications such as NetLinx Studio TPD4 or IREdit 14 Press the System Number field to open a Keyboard and enter the Unique System Number of the PC used as the Virtual Master 15 Click Done to accept the new value and return to the System Settings page 16 Do not alter the Master Port Number value as this is the default value used by NetLinx 17 Press the Back button to open the Protected Setup page Cs E A Ri 18 Press the on screen Reboot button to save any changes and restart the panel The panel will now be connected to the master 19 Click the OnLine Tree tab in the Workspace window to view the devices on the Virtual System The default System value is one 20 Right click on the
217. x can be used Special escape sequences The system has only a limited knowledge of URL formats as it transparently passes the URL information onto the server for translation A user can then pass any parameters to the server side programs such as CGI scripts or active server pages However the system will parse the URL looking for special escape codes When it finds an escape code it replaces that code with a particular piece of panel button or state information For example http www amx com img asp device DV would become hitp www amx com img asp device 10001 Other used escape sequences include Escape Sequences Sequence Panel Information DV Device Number SY System Number IP IP Address HN Host Name MC Mac Address ID Neuron ID PX X Resolution of current panel mode file PY Y Resolution of current panel mode file BX X Resolution of current button BY Y Resolution of current button BN Name of button ST Current state AC Address Code AP Address Port CC Channel Code CP Channel Port LC Level Code LP Level Port Appendix B Wireless Technology Overview of Wireless Technology e 802 11b 2 4 GHz and 802 11a 5 GHz are the two major WLAN standards and both operate using radio frequency RF technology Together the two standards are together called Wi Fi and operate in frequency bands of 2 4 GHz and 5 GHz respectively The 802 11b spe
218. xamples The following are some common input masking examples Output Examples Common Name Input Mask Input IP Address Quad 0 255 Any value from 0 to 255 Hour 1 12 Any value from 1 to 12 Minute Second 0 59 Any value from 0 to 59 Frames 0 29 Any value from 0 to 29 Phone Numbers 999 000 0000 555 555 5555 Zip Code 00000 9999 75082 4567 NOTE URL Resources A URL can be broken into several parts For example with the URL http www amx com company info home asp this URL indicates that the protocol in use is http HyperText Transport Protocol and that the information resides on a host machine named www amx com The image on that host machine is given an assignment by the program name of company info home asp Active Server Page The exact meaning of this name on the host machine is both protocol dependent and host dependent The information normally resides in a file but it could be generated dynamically This component of the URL is called the file component even though the information is not necessarily in a file A URL can optionally specify a port which is the port number to which the TCP IP connection is made on the remote host machine If the port is not specified the default port for the protocol is used instead For example the default port for http is 80 An alternative port could be specified as http www amx com 8080 company info home asp Any legal HTTP synta
219. y_ LFA Operation Reference Guide MVP 5100 5150 Modero Viewpoint Widescreen Touch Panels m a n E n e Se Mio Modero Touch Panels Last Updated 12 2 2008 AMX Limited Warranty and Disclaimer All products returned to AMX require a Return Material Authorization RMA number The RMA number is obtained from the AMX RMA Department The RMA number must be clearly marked on the outside of each box The RMA is valid for a 30 day period After the 30 day period the RMA will be cancelled Any shipments received not consistent with the RMA or after the RMA is cancelled will be refused AMX is not responsible for products returned without a valid RMA number Warranty Repair Policy AMX will repair any defect due to material or workmanship issues during the applicable warranty period at no cost to the AMX Authorized Partner provided that the AMX Authorized Partner is responsible for in bound freight and AMX is responsible for out bound ground freight expenses The AMX Authorized Partner must contact AMX Technical Support to validate the failure before pursuing this service AMX will complete the repair and ship the product within five 5 business days after receipt of the product by AMX The AMX Authorized Partner will be notified if repair cannot be completed within five 5 business days Products repaired will carry a ninety 90 day warranty or the balance of the remaining warranty whichever is greater Products that are re
220. zes the text string 12345678 with prompt text ENTER PASSWORD AKR Remove keyboard or keypad that was displayed using AKEYB AKEYP PKEYP Remove the AKB AKP PKP EKP or TKP commands Keyboard Syntax Keypad 1 AKR Example SEND COMMAND Panel AKR Removes the Keyboard Keypad BEEP Syntax Output a beep I BEEP Example SEND COMMAND Panel BEEP Outputs a beep BRIT Syntax Set the panel BRIT lt brightness level gt brightness Variable brightness level 0 100 Example SEND COMMAND Panel BRIT 50 Sets the brightness level to 50 BRT Syntax Set the panel BRT lt brightness level gt brightness Variable brightness level 0 100 Example SEND COMMAND Panel BRT 70 Sets the brightness level to 70 DBEEP Syntax Output a DBEEP double beep Example SEND COMMAND Panel DBEEP Outputs a double beep Panel Runtime Operation Commands Cont EKP Pops up the keypad icon and initializes the text string to that specified The Prompt Text is Extend the optional Keypad Syntax EKP lt initial text gt lt prompt text gt Variables initial text 1 50 ASCII characters prompt text 1 50 ASCII characters Example SEND COMMAND Panel EKP 33333333 Enter Password Pops up the Keypad and initializes the text string 33333333 with prompt text Enter Password PKEYP Pops up the keypad icon and initializes the text string to that

AMX MVP-5100 Computer Monitor User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents