American Standard T050.210 Thermostat User Manual
Contents
1. Bs 4 1 2 NPT INLET 1 2 NPT 1 2 NPT INLET TUB 5 7 8 gt 1 5 8 2 1 2 lt gt THERMOSTATIC BATH THERMOSTATIC SHOWER INSTALLATION THERMOSTATIC SHOWER INSTALLATION USING A SHOWER INSTALLATION USING A DIVERTER VALVE FIXED DIVERTER VALVE FIXED SHOWER HEAD ADJUSTABLE USING A TWIN ELL DIVERTER SHOWER HEAD AND ADJUSTABLE HAND HAND HELD SHOWER ON OFF VALVE AND TWO SPOUT AND FIXED SHOWER HELD SHOWER BODY SPRAYS DIVERTER VALVE eZ BBB BEES a a DIVERTER a VALVE nnan 80 86 18 OPTIONAL TOP OF TUB RIM Hell bell BOTTOM OF TUB Sf TUB PORT MUST ee TUB PORT MUST BE PLUGGED BE PLUGGED IMPORTANT WHEN NOT USING A NOTE MINIMUM FLOWING PRESSURE REQUIRED FOR DIVERTER SPOUT A SEPARATE THIS SYSTEM OPERATING WITH ONE SHOWER HEAD DIVERTER VALVE MUST BE USED AND 2 BODY SPRAYS IS 40 PSI ON OFF VALVE MUST BE PLUGGED m DO NOT SOLDER DIRECTLY TO THE VALVE BODY THIS WILL DAMAGE ROUGHING IN THE VALVE WARNING THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES Prepare water supplies per ROUGHING IN DIMENSIONS Make sure the finished wall is between the minimum and maximum rough dimension Install VALVE at indicated height and depth Make sure the TOP marking on the PLASTER GUARD is up Connect the hot and cold water supplies Assemble all connecting pip2. and the cold CHECK STOP 5 has a blue top sola Lg CHECK STOP CHECK STOPS 4 5 are supplied in the open position J COLD BLUE Closing using 5 32 4 mm hex wrench to pressure test and to check for leaks To flush lines remove the CHECK STOPS 4 5 and run water If desired the TEMPERATURE CONTROL UNIT can be removed Reinstall CHECK STOPS 4 5 and CONTROL UNIT 6 if it was removed Remove PLASTER GUARD 2 if still installed Turn on water supplies and check for leaks Reassemble PLASTER GUARD 2 and FINISH WALL Beware of Freezing No water should remain in the MIXING VALVE if freezing is a possibility CHECK STOP Remove the CHECK STOPS 4 5 to completely HOT RED drain the MIXER UNIT 1 TEMPERATURE ADJUSTMENT Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD Check that arrow marking B points vertically upwards If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUNT and reinstall KNOB MOUNT with arrow B pointing upwards The maximum mixed water temperature is set at 109 F at the factory F r i TEMPERATURE This setting can be changed if desired LIMIT STOP Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water A temperature to 104 F or 112 F SECURING ye For 100 F adjustment turn the water supply on Turn KNOB MOUNT until the spout RING temperature
3. is 100 F Check that arrow marking A on the KNOB MOUNT still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE RED LOCKING Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve DEVICE E Reinstall the KNOB MOUNT so that the arrow marking A points upwards E Reinstall RED LOCKING DEVICE TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making adjustment impossible proceed as follows 5 CHECK STOP E Shut off water supply iF hres E Remove handle and rim E Remove check stops and re install them transposed Important note RED CHECK STOP is now on the right of the mixer body and the BL CHECK STOP is now on the left E Turn the water supply back on and perform the temperature adjustment in step 2 CHECK STOP RED TO BLUE M968480 CERATHERM 3 4 CENTRAL THERMOSTAT WITH VOLUME CONTROL MODEL NUMBER 912647 0070A O RING A953971 0070A CHECK STOP COLD BLUE A994352 0070A CARTRIDGE g 923348 0070A E HANDLE ADAPTER N K 918428 0070A Wy CARTRIDGE SCREW i 5 953963 0070A 954040 0070A THERMOSTAT HANDLE EXTENSION CARTRIDGE A953972 0070A CHECK STOP HOT RED 912647 0070A j tl T 0070A O RING CALIBRATION UNIT 963434 YYYOA DEEP ROUGH KIT SOLD SEPARATELY HOT LINE FOR HELP For toll free information and answers to your questions c
4. push the BLACK CLAMP 1 on the SECURING RING 2 to the right pull off KNOB MOUNT 3 and reinstall KNOB MOUNT 3 with arrow B pointing upwards SET HOT LIMIT STOP m The maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired m Remove the TEMPERATURE LIMIT STOP 4 H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water temperature to 104 F or 112 F For 100 F adjustment turn the water supply on Turn KNOB MOUNT 3 until the spout temperature is 100 F Check that arrow marking A on the KNOB MOUNT 3 still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE 5 Remove KNOB MOUNT 3 without turning by sliding out as indicated by the arrow Reinstall the KNOB MOUNT 3 so that the arrow marking A points upwards Reinstall RED LOCKING DEVICE 5 OPERATING THE VALVE If the system is delivering all Hot or all Cold and no mixed water the pipes are probably transposed If a temperature over 100 F is desired pull the RED STOP BUTTON 1 away from the body of the MIXER UNIT and turn the TEMPERATURE KNOB This will increase the mixed water temperature up to the maximum limit previously A selected in step 4 M968417 REV 1 1 CERATHERM TRIM KIT for CENTRAL THERMOSTAT WITH VOLUME CONTROL MODEL NUMBER TO50 210 907090 YYYOA CAP 953961 0070A ESCUTCHEON CARR
5. 18572 0070A CARTRIDGE SCREW 994053 0070A N SS oJ 923348 0070A Y HANDLE ADAPTER 953963 0070A 953960 0070A HANDLE EXTENSION THERMOSTAT CARTRIDGE 953951 0070A CHECK STOP HOT RED ae 953957 0070A CALIBRATION UNIT 963434 YYYOA DEEP ROUGH KIT SOLD SEPARATELY HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968255Rev 1 1 Amirieam Standard Installation Instructions CERATHERM 3 4 CENTRAL THERMOSTAT WITH VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please Certified to comply with ANS CATE te IN f F ASSE 1016 read these instructions carefully before you begin pasate ROUGHING IN DIMENSIONS CONNECTIONS ARE 3 4 NPT 3 4 NPT JO t 3 15 16 eT lea 3 4 NPT INLET 1 5 8 2 1 2 THERMOSTATIC BATH THERMOSTATIC SHOWER INSTALLATION THERMOSTATIC SHOWER INSTALLATION USING A SHOWER INSTALLATION USING A DIVERTER VALVE FIXED DIVERTER VALVE FIXED SHOWER HEAD ADJUSTABLE HAND HELD SHOWER ON OFF VALVE AND T
6. AAmbrican Standard Installation Instructions CEATHER M TO50 210 TRIM KIT for CENTRAL THERMOSTAT with VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years z Certified to comply with ANSI A112 18 1M To ensure that your installation proceeds smoothly please ass 1016 read these instructions carefully before you begin M968417 REV 1 1 ROUGHING IN DIMENSIONS i FINISHED 1 11 16 to 2 1 2 WALL Recommended Tools 3 Flat Blade Screwdriver Phillips Screwdriver CARE INSTRUCTIONS m Remove as much surface dirt and film using clear water and soft cotton cloth as described above E To keep your new faucet looking new please follow these simple care instructions Use any of the following to remove tough surface film and build up Mild liquid detergents Clear ammonia free liquid glass cleaners Non acidic non abrasive gentle liquid or fully DO NOT dissolved powder cleansers mixed according to manufacturers directions E Nonr abrasive liquid polishers DO E Simply rinse the faucet clean with clear water E Dry the faucet with a soft cotton cloth E Do not use any abrasive cleaners cloths or paper towels E Do not use any cleaning agents containing acids polish abrasives or harsh cleaners or Once clean rinse faucet again with clear water to soaps thoroughly r
7. IER 918327 0070A ESCUTCHEON CARRIER SCREWS 954026 YYYOA VOLUME CONTROL HANDLE BASE 953946 YYYOA ESCUTCHEON 909750 YYYOA HANDLE RING 918428 0070A VOLUME CONTROL SCREW 907065 YYYOA HANDLE CAP 953976 YYYOA 051313 YYYOA TEMPERATURE VOLUME CONTROL CONTROL HANDLE BASE HANDLE ag 909750 YYYOA 918378 YYYOA S bs MANGLE RING ESCUTCHEON SCREWS 7 S1640 0070A TEMPERATURE SCREVV ery ty 060441 YYYOA TEMPERATURE CONTROL HANDLE Replace the YYY with appropriate finish code CHROME POLISHED BRASS SATIN CHR POL BRASS MIXAGE HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968417 REV 1 1 American Standard Installation Instructions CERATHERM ane CENTRAL THERMOSTAT WITH VOLUME CONTROL Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please Pepa to TompyAv ANSAT ATEN ri F ASSE 1016 read these instructions carefully before you begin M968255Rev 1 1 ROUGHING IN DIMENSIONS CONNECTIONS ARE 1 2 NPT 1 2 NPT foe a 6 1 4 gt A 3 15 16 HA T ica Il
8. WO BODY SPRAYS D D DIVERTER amp VALVE DIVERTER CEE E E 80 86 l X ON OFF TUB PORT F r VALVE 18 OPTIONAL MUST BE PLUGGED i TOP OF TUB RIM 3 4 BOTTOM OF TUB TUB PORT MUST f a IY TUB PORT MUST BE PLUGGED BE PLUGGED IMPORTANT WHEN NOT USING A NOTE MINIMUM FLOWING PRESSURE REQUIRED FOR DIVERTER SPOUT A SEPARATE THIS SYSTEM OPERATING WITH ONE SHOWER HEAD DIVERTER VALVE MUST BE USED AND 2 BODY SPRAYS IS 40 PSI DO NOT SOLDER DIRECTLY TO THE VALVE BODY THIS WILL DAMAGE ROUGHING IN THE VALVE WARNING THE TEMPERATURE CONTROL ELEMENT AND CHECK STOP VALVES Prepare water supplies per ROUGHING IN DIMENSIONS Make sure the finished wall is between the minimum and maximum rough dimension Install VALVE at indicated height and depth Make sure the TOP marking on the PLASTER GUARD is up Connect the hot and cold water supplies Assemble all connecting pipes Flush lines to remove any dirt Connections are 3 4 NPT Assemble the connection pipe to one of the MIXED OUTLETS of the VALVE Cap the other MIXED OUTLET Tub port is fitted with a plug at the factory IMPORTANT INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES INTO THE PIPING SYSTEM PORT If the CHECK STOPS 4 5 were removed during installation ensure the hot and cold CHECK STOPS 4 5 are not reversed The hot CHECK STOP 4 has a red top
9. all 1 800 442 1902 Weekdays 8 00 a m to 8 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2003 M968480
10. emove cleaner or polish and blot dry with a soft cotton cloth Regular and routine cleaning will reduce the need for heavy cleaning and polishing If heavy cleaning is required the following procedures are recommended Failure to follow these care instructions may damage the Faucet s finish TRIM INSTALLATION E Push CAPS 1 over the O RING SEALS 2 E Push ESCUTCHEON HOLDER 3 with lightly greased O RING SEAL 4 over CAP 1 Push on ESCUTCHEON 5 and attach with 50mm SCREWS 6 to valve body HANDLE INSTALLATION Push TEMPERATURE CONTROL KNOB 1 with the red stop onto KNOB MOUNT 2 Push RING 3 onto TEMPERATURE CONTROL KNOB 1 and attach with SCREW 4 Push VOLUME CONTROL KNOB 6 onto HANDLE ADAPTER 8 Push RING 3 onto VOLUME CONTROL KNOB 6 and and attach with SCREW 7 Press on KNOB CAPS 5 TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION CHECK STOP Should the hot and cold water supply pipes have been transposed making BLUE TO RED adjustment impossible proceed as follows E Shut off water supply E Remove handle and rim E Remove check stops and re install them transposed Important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left EKTO Turn the water supply back on and perform the temperature adjustment in step 4 RED TO BLUE TEMPERATURE CALIBRATION Check that arrow marking B points vertically upwards If not
11. es Flush lines to remove any dirt Connections are 1 2 NPT Assemble the connection pipe to one of the MIXED OUTLETS of the VALVE Cap the other MIXED OUTLET Tub port is fitted with a plug at the factory IMPORTANT INSTALL ANY REQUIRED SHUT OFF OR DIVERTER VALVES INTO THE PIPING SYSTEM PORT If the CHECK STOPS 4 5 were removed during installation ensure the hot and cold CHECK STOPS 4 5 are not reversed The hot CHECK STOP 4 has a red top and the cold CHECK STOP 5 has a blue top Nea CHECK STOP CHECK STOPS 4 5 are supplied in the open position COLD BLUE Closing using 5 32 4 mm hex wrench to pressure test and to check for leaks To flush lines remove the CHECK STOPS 4 5 and run water If desired the TEMPERATURE CONTROL UNIT can be removed Reinstall CHECK STOPS 4 5 and CONTROL UNIT 6 if it was removed Remove PLASTER GUARD 2 if still installed Turn on water supplies and check for leaks Reassemble PLASTER GUARD 2 and FINISH fo WALL CHECK STOP Beware of Freezing No water should remain HOT RED in the MIXING VALVE if freezing is a possibility Remove the CHECK STOPS 4 5 to completely drain the MIXER UNIT 1 TEMPERATURE ADJUSTMENT Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD Check that arrow marking B points vertically upwards If not push the BLACK CLAMP on the SECURING RING to the right pull off KNOB MOUNT and reinstall KNOB MOUNT with arrow B pointing upwards T
12. he maximum mixed water temperature is set at 109 F at the factory This setting can be changed if desired TEMPERATURE LIMIT STOP Remove the TEMPERATURE LIMIT STOP H shaped Black Plastic part Reinstall it at the desired notch as indicated in the diagram to limit the maximum mixed water Y temperature to 104 F or 112 F SECURING a For 100 F adjustment turn the water supply on Turn KNOB MOUNT until the spout RING temperature is 100 F Check that arrow marking A on the KNOB MOUNT still points upward after adjusting the thermostat to 100 F If not pull out the RED LOCKING DEVICE RED LOCKING Remove KNOB MOUNT by pulling it towards you while standing directly in front of the valve DEEE E Reinstall the KNOB MOUNT so that the arrow marking A points upwards E Reinstall RED LOCKING DEVICE TRANSPOSED SUPPLY PIPING OR BACK TO BACK INSTALLATION Should the hot and cold water supply pipes have been transposed making CHECK STOP adjustment impossible proceed as follows p BLUE TO RED m Shut off water supply m Remove handle and rim E Remove check stops and re install them transposed E Important note RED CHECK STOP is now on the right of the mixer body and the BLUE CHECK STOP is now on the left E Turn the water supply back on and perform the temperature adjustment in step 2 ae M968255Rev 1 1 CERATHERM CENTRAL THERMOSTAT WITH VOLUME CONTROL MODEL NUMBER 953950 0070A CHECK STOP COLD BLUE CARTRIDGE A9
Download Pdf Manuals
Related Search