American Standard 2455 Indoor Furnishings User Manual
Contents
1. Supply valve partly closed Supply pressure too low Partially clogged trapway and or drain pipe and or vent Check that water level is set to correct height in tank also verify the flush valve adjustments are set as per Step 10 Open supply valve fully Be sure that proper supply tube size is used Remove obstruction Consult a plumber if necessary Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection Poor bowl to tank floor connection Review Step 9 of installation procedure Review Step 4 through 7 of installation procedure Toilet does not shut off Flush valve seat and or rubber seal worn or deformed Sand or debris lodged in water control Shut off water supply Replace flush valve or flush valve silicone seal Shut off water supply Remove cap and clean per Step 14 AS AMERICA INC AMERICAN STANDARD TWO YEAR LIMITED WARRANTY If inspection of this AS America Inc American Standard plumbing product within two years after its initial installation confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance b2. COUPLING NUT could result in breakage and potential flooding With correct washers in place see Step 9a tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN 7301144 100 Rev F ADJUSTMENTS a Adjust water level Water level should be adjusted to level indicated on tank by adjusting float cup See Step 11 for water level adjustment method Make sure Full Flush Adjustment is at RERET serves LEVEL HERE the bottom setting 0 A higher setting N S will result in less water and is not recommended i H PARTIAL i 3 FLUSH Make sure Partial Flush Adjustment is Turn on water supply at the bottom setting 0 A higher setting Submerge the FLOAT CUP will result in less water and is not under the water for 30 WATER LEVEL recommended seconds Adjust the water to ADJUSTMENT NOTE The Fill Valve d ih fil desired level by turning ADJUSTABLE b ING FII vawe 0065 NOLNAVE ATEI WATER LEVEL ADJUSTMENT J SEAL tube The refill port on the Fluidmaster fill ROD and moving FLOAT CUP valve is 100 blocked off Please ensure that the correct repair part is used as this fill valve varies from the standard Fluidmaster 400A up or down LOCK NUT E THREADED e To remove Flush Valve apply slight downward pressure and twist it until the PARTS FOR WATER flush valve disengages from the bayonet See STE
3. INSTALLATION INSTRUCTIONS Americam Standard CARE AND MAINTENANCE Style That Works Better FloWise DUAL FLUSH 2 PIECE TOILET Model 2479 216 2479 516 2476 216 2476 516 2779 516 E ys Model 2480 216 2480 516 2484 216 2484 516 2778 516 rcs au 2566 216 Right Height wewo er Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET a Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl b Disconnect and remove supply line NOTE f replacing valve first shut off main water supply c Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases d Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed yy ROUGHING IN DI
4. MENSIONS Models 2480 216 2480 516 2484 216 2484 516 Models 2479 216 2479 516 2778 516 2566 216 Right Height FNSH Walk 2476 216 2476 516 2779 516 i FINISHED WAL ER 794mm gt ETE 31 1 4 31 1 4 1 5 8 1 4 432mm __ 197mm 17 pusH 7 3 4 BUTTON 70mm 470mm 18 1 2 i 18 1 2 l C L OF SEAT POST HOLES C L OF SEAT POST HOLES Pa 140mm 5 1 2 CENTRES ra 140mm 5 1 2 CENTRES SUPPLY AS h SUPPLY H n i 7 ReaD REQ D 448mm 375mm 17 5 8 14 3 4 410mm FINISHED K 16 1 8 FLOOR 397mm 14MM je sd 15 5 8 FINISHED 4 1 2 C L OF OUTLET OSR 3300 Nit OF OUTLET CLOSET FLANGE TAPERED s WASHER INSTALL CLOSET BOLTS CLOSET Install closet bolts in flange channel GA F BOLT turn 90 and slide into place 6 gt E 152mm apart and parallel to wall Ces Co TEMPORARLLY set toilet in place Place tapered washer and nuts onto the bole ae shown in Step 5 Mark bolt INSTALL WAX SEAL length needed for bolt cap clearance Invert toilet on floor cushion to POSITION TOILET ON FLANGE Remove toilet Precut the bolts to prevent damage and install wax a Unplug floor waste opening and install toilet on closet flange length by twisting the nut onto the bolt ring evenly around waste flange so bolts project through mounting holes past the cut mark then cutting the bolt horn wi
5. ND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed Go to our website at www fluidmaster com for more solutions to toilet problems For troubleshooting information please contact Fluidmaster mc 30800 Rancho Viejo Road San Juan Capistrano CA 92675 949 728 2000 800 631 2011 www fluidmaster com 2001 Fluidmaster Inc Registered trademark of Fluidmaster Inc Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc PROBLEM TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION Does not flush Water supply valve closed Supply line blocked Sand or debris lodged in water control Open valve and allow water to fill tank Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see Step 14 Shut off water supply Remove cap and clean as per Step 14 Poor or sluggish flush Bowl water level too low
6. P 9 e To reinstall Flush Valve reverse the above procedure making sure the blue Diagram 1 Partial Flush Button will line up with the Partial Flush Button on the Tank Lid CONE WASHER gay COUPLING NUT CU HAND TIGHT ONLY 174 FLUSH BUTTONS ON TANK e Pressing both buttons at once will flush the full flush amount Large button for 1 6 gal flush or 6L flush solid waste 1 6 gal flush The Partial Flush Button should line up over the blue actuator 6L flush on the flush tower in the tank Small button for e The Full Flush Button should line up over the white actuator liquid waste i 8 gal flush on the flush tower in the tank sL flush LIES CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked
7. efore installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard This warranty DOES NOT COVER any damage caused by the use of in tank cleaners American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the Un
8. inside tank NOTE XXX represents color or trim finish options Specify when ordering TANK NUMBER PART NO DESCRIPTION Ey 4035 516 735130 400 XXX0A TANK COVER WITH PUSH BUTTON 738565 426 0070A FLUIDMASTER 400A VALVE 738565 427 0070A FLUIDMASTER 400A VALVE 7301143 0070A TANK COUPLING KIT 258 7381002 400 0070A DUAL FLUSH VALVE 7381002 401 0070A DUAL FLUSH VALVE 7381003 XXX0A PUSH BUTTON ASSEMBLY TOP MOUNT 034783 XXX0A BOLT CAP KIT 760127 XXX0A TOILET SEAT 760130 XXX0A TOILET SEAT SLOW CLOSE 7381042 0070A FLUSH VALVE SILICONE SEAL 7301144 100 Rev F IMPORTANT Always clear sand and rust from system e Make sure water supply is off Remove valve TOP by lifting arm and rotating top and arm 1 8 turn counterclockwise pressing down slightly on cap GUARANTEE This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year Units returned to Fluidmaster will be replaced without charge e While holding a container over the uncapped VALVE to prevent splashing turn water supply on and off a few times Leave water supply off e Replace TOP by engaging lugs and rotating 1 8 turn clockwise MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITION VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF A
9. is snugged down evenly against bowl surface USE NUT DRIVER OR DEEP SOCKET RACHET A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT t INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions Before continuing determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings METAL COPPER FLARED TUBING METAL FLANGED TUBING LOCK NUT gt EXISTING WASHER EFs LOCK NUT CONE lt WASHER EXISTING COUPLING NUT COUPLING WATER SHUT OFF WATER SHUT OFF These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in water leakage Water supply tube or pipe must extend at least 1 2 inside threaded shank of valve does not apply to flanged tubing Use existing coupling nut and washer CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE METAL SPIRAL TUBING EPS Lock NUT EXISTING CONE VINYL BRAIDED CONNECTOR N LOCK NUT WASHER COUPLING NUT WATER SHUT OFF WATER SHUT OFF Captive cone washers already included No additional washers needed Use existing spiral cone washer Fluidmaster cone washer may not seal completely on spiral type supply line CAUTION Overtightening of LOCK NUT or
10. ited States American Standard Inc P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 www americanstandard us com In Canada American Standard 2480 Stanfield Rd Mississauga Ontario Canada L4Y 1S2 Toll Free 800 387 0369 www americanstandard ca In Mexico Customer Service Manager Ideal Standard S A de C V Via Morelos 330 Col Santa Clara Ecatepec 55540 Edo Mexico www americanstandard com mx 7301144 100 Rev F
11. th tapered end of ring b Loosely install retainer washers and nuts Side of washers to the desired length with a hacksaw facing toilet Apply a thin bead of marked THIS SIDE UP must face up Unscrew the nut to repair the threads sealant around toilet base Re install bolts in flange Product names listed herein are trademarks of AS America Inc AS America Inc 2008 7301144 100 Rev F USE FUTURE R F O SAVE BOLT CAP WASHER NUT INSTALL TOILET Tank Installation Kit Includes 2 bolts 2 rubber washers 4 metal washers 4 metal nuts 2 plastic nuts 1 large rubber gasket a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor A CAUTION DO NOT OVERTIGHTEN NUTS Install caps on washers Smooth off the bead of sealant around base Remove excess sealant RUBBER RUBBER GASKET WASHER NUT INSTALL TANK a Discard plastic nuts b Install tank mounting bolts and rubber washers from inside tank through mounting holes and secure with one metal washer and one nut per bolt c Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening d With tank parallel to wall secure tank to bowl using remaining two metal washers and nuts Alternately tighten nuts until tank
Download Pdf Manuals
Related Search