American Standard 0780.100 Indoor Furnishings User Manual
Contents
1. CLOSET BOLT WASHER WASHER NUT INSTALL TANK a Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening b Insert tank mounting bolts and rubber washers from inside tank through mounting holes and secure with metal washers and nuts c With tank parallel to wall alternately tighten nuts until tank is snugged down evenly against bowl surface A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions 730489 100 Rev B CAUTION Overtightening of COUPLING NUT could result in breakage and potential flooding TANK WATER INLET WASHER _ 2e COUPLING NUT 7 FLEXIBLE a SUPPLY VALVE NUT a i a COMPRESSION COLLAR FLOW RATE TO RAISE ADJUSTMENT LIFT OVERFLOW TUBE nee FIG 10A WATER CONTROL ASSEMBLY WATER LINE LEVEL WATER INLET FLUSH VALVE ASSEMBLY ADJUSTMENTS a CONNECT WATER SUPPLY a Connect water supply line between shutoff valve and tank water inlet fitting Tighten COUPLING NUT 1 4 turn beyond hand tight Check that refill tube is inserted into overflow tube Turn on supply valve and allow tank to fill until float rises to shutoff position Check f2. INSTALLATION INSTRUCTIONS For Two Piece Toilets with Aquameter Fill Valve REPERTOIRE 2266 2483 HERITAGE 2176 ANTIQUITY 2264 2464 WILLIAMSBURG 2264 702 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level IE REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed A ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below CLOSET FLANGE FINISHED WALL 42 305mm i C
3. LOSET BOLTS SUPPLY AS REQUIRED a and slide into place 6 152 mm apart and FLOOR parallel to wall Americam Teal Thasa Sadna INSTALL CLOSET BOLTS Standard Stemdard Standard Stavdard edela Saniwares Product names listed herein are trademarks of American Standard Inc American Standard Inc 2006 730489 100 Rev B Install closet bolts in flange channel turn 90 U S FUTURE R FO SAVE INSTALL WAX SEAL Invert toilet on floor cushion to prevent damage and install wax ring evenly around waste flange horn with tapered end of ring facing toilet Apply a thin bead of sealant around base flange POSITION TOILET ON FLANGE a Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes b Loosely install mounting clip for Heritage only retainer washers and nuts Side of washers marked THIS SIDE UP must face up c Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor A CAUTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED b Install covers on washers If necessary cut bolt height to size before installing caps c Smooth off the bead of sealant around base Remove excess sealant REPERTOIRE ANTIQUITY HERITAGE amp WILLIAMSBURG a CAP COVER ray CAP NUT O CLOSET DN BOLT MOUNTING CLIP
4. RG ONLY BOLT CAP KIT INCL 2 COVERS amp WASHERS WATER CONTROL ASS y W FLOAT BALL FLUSH VALVE COUPLING KIT BOWL TO TANK FLAPPER ASSEMBLY LEE CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish FOR 4074 039 HERITAGE PART NO DESCRIPTION 730283 XXX0A TRIP LEVER 047227 XXX0A BOLT CAP COVER PLATE KIT 207 738352 0070A WATER CONTROL ASS y W FLOAT BALL 738181 0070A FLUSH VALVE 047158 0070A COUPLING KIT BOWL TO TANK 738258 0070A FLAPPER ASSEMBLY A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite 730489 100 Rev B TROUBLESHOOTING GUIDE PROBLEM Does not flush POSSIBLE CAUSE Water supply valve closed Supply line blocked Flush valve chain too loose or disconnected Stuck float float rod Water control flow rate too restricted Tank water level too low Bowl water level too low Poor or sluggish flush Supply valve partly clo
5. n length as needed Follow installation instructions to reduce water control flow rate which will lift lowest position of float rod without affecting water level Replace flapper flush valve assembly as needed Shut off water supply Consult a plumber if necessary Follow instructions to increase water control flow rate AMERICAN STANDARD ONE YEAR LIMITED WARRANTY If inspection of this American Standard plumbing product within one year after its initial installation confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or con
6. or leakage at fittings tighten or correct as needed Do not use plumber s putty to seal these fittings Flush tank and check that tank fills and shuts off within 30 to 60 seconds and tank water level is set as specified on tank rear wall To adjust water level turn water level adjustment screw counterclockwise to raise level turn adjustment screw clockwise to lower level To adjust flow rate tank fill time turn flow rate adjustment screw clockwise to decrease flow rate increase fill time turn adjustment screw counterclockwise to increase flow rate decrease fill time Carefully position tank cover on tank The flush valve float has been factory set and does not require adjustments Repositioning of the float will change the amount of water used which may effect the toilet s performance If bowl fails to siphon an adjustment may be required with the lift chain Simply remove the bead chain from the retainment clip see Fig 10A and take up slack on the chain and reinsert on lift rod Make sure the chain is not too taught REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank NOTE XXX represents color or trim finish options Specify when ordering FOR 4094 ANTIQUITY 4095 REPERTOIRE AND 4094 702 WILLIAMSBURG PART NO 730288 XXX0A 730535 XXX0A 034783 XXX0A 738462 0070A 738181 0070A 047158 0070A 738258 0070A DESCRIPTION TRIP LEVER TRIP LEVER WILLIAMSBU
7. sed Flush valve closes early due to high supply pressure Partially clogged trapway and or drain pipe and or vent Supply pressure too low Toilet leaks Poor supply line connection Poor bowl to tank floor connection Toilet does not Tank water level too high shut off Float rod or float ball depressed by tank cover Flush valve chain too tight holding flush valve open Float rod interfering with flush valve closing Flush valve seat and or flapper worn or deformed Sand or debris lodged in water control Noisy Flush Water control flow rate too restricted CORRECTIVE ACTION Open valve and allow water to fill tank Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Readjust chain length as required Adjust to allow free downward movement of float arm Follow instructions to increase water control flow rate Follow instructions to adjust water level Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged Open supply valve fully Be sure that proper supply tube size is used Follow instructions to reduce water control flow rate Remove obstruction Consult a plumber if necessary Normal supply pressure must be at least 20 psi Review Step 9 of installation procedure Review Step 4 through 7 of installation procedure Follow instructions to adjust water level Readjust float rod Readjust chai
8. sequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States American Standard Inc P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 www AmericanStandard US com In Canada American Standard 2480 Stanfield Rd Mississauga Ontario Canada L4Y 1S2 Toll Free 800 387 0369 www AmericanStandard ca In Mexico Customer Service Manager Ideal Standard S A de C V Via Morelos 330 Col Santa Clara Ecatepec 55540 Edo Mexico www AmericanStandard com mx 730489 100 Rev B
Download Pdf Manuals
Related Search