AEG 40730 Dishwasher User Manual
Contents
1. Adjusting the height of the upper basket with upper basket raised with upper basket lowered Maximum height of dishes in the Upper basket Lower basket 22 cm 30 cm 24 cm 29 cm The height of the baskets can also be adjusted when they are loaded Raising lowering the upper basket 1 Pull out the upper basket complete ly 2 Raise the upper basket as far as it will go and then lower it vertically The upper basket will latch into the lower or the upper position 15 Adding detergent N Detergents remove the dirt from dishes and cutlery The detergent must be added before the cycle starts Only use detergent intended for do mestic dishwashers The detergent compartment is lo cated on the inside of the door If the lid is closed Press the release button The lid will spring open Place the detergent in the detergent dispenser The markings indicate the dosing levels for powder detergents 20 30 corresponds to approx 20 30 ml of detergent Follow the manufacturer s instruc tions with regard to dosing and storage Close the lid and press until it locks into place In the case of very heavily soiled dishes fill the adjoining compart ment 1 with additional detergent This detergent comes into use during the pre wash cycle E E GJ Concentrated detergents2. 0 o AA eee 22 Whatto d0 thio sien faved NAAA 25 Remedying small malfunctions eens 25 If the dishwashing results are not satisfactOory 27 Disposal it Banta os 28 Technical data ooo eee ye ee eae 29 Notes for Test Institutes aaa e eaaa aee 30 Installation and connection instructions 32 Safety information for the installation 32 Installing the dishwasher eaaa aee 33 Connecting the dishwasher eee eee 35 Guarantee Customer Service 39 SEFVICE sesa 00000000 43 Operating Instructions A Safety Prior to using for the first time e Follow the Instructions for installation and connection Correct use e The dishwasher is only intended for washing domestic dishes e Additions or modifications to the dishwasher are not permitted e Use only special salt detergent and rinse aid suitable for domestic dishwashers e Do not put any solvents in the dishwasher This could cause an explo sion Child safety e Keep packaging away from children There is a risk of suffocation e Children often do not recognise the hazards associated with electrical appliances Don t allow children to use the dishwasher unsupervised e Make sure that children and pets don t climb into the dishwasher Could e
3. of injury To ensure that all items of cutlery in the cutlery basket can be reached by the water you should 1 Place the grid insert on the cut 2 Place forks and spoons in the lery basket cutlery basket s grid insert with their handles pointing down wards VEZ 4J 3435 v awnaa Y za TII 145 397 1343 4181 44 11 CPET Bunei asatitij gum u For larger utensils such as whisks leave off one half of the cutlery grid Pots Pans Large Plates Load larger and heavily soiled dishes and pans in the lower basket Max diameter for plates 29 cm AAAHHH SSSSSSSSSSSS 000 0000 Qoo 00 25002 0000 0000000000022 13 To make it easier to load larger dish es the two plate rests on the right in the lower basket can be folded down Cups Glasses Coffee Service Load smaller fragile crockery and long sharp cutlery in the upper bas ket e Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items e The cup racks can be folded up out of the way for tall crockery items e Lay or hang wine and brandy glasses in the slots in the cup racks
4. Customer Care Department To ensure that 4 y the function of the appliance is not impeded the internal diameter of extension hoses must be 19 mm 5 e Extension hoses must not be laid ii 5 more than a maximum distance of 9 3 metres horizontally the maxi P mum permitted height for the con nection for the drain hose is then Pa TN 85 cm Sink outlet connection e The outlet of the drain hose 19 mm fits all commonly available sink outlet types The outer diameter of the sink outlet connection must be at least 15 mm he drain hose must be fixed to the sink outlet connection using the hose clamp supplied Water drainage if the dishwasher is built in at high level If the dishwasher is installed at a high level and the drain hose connec tion is less than 30 cm from the lower edge of the appliance adapter kit ET 111099520 must be fitted by the Customer Care Department Water drainage into sink only possible with free standing appli ances If you wish to hang the drain hose in a wash basin use a detachable hose elbow You can obtain this from customer service by referring to spare part number ET 646 069 190 Fit the elbow to the drain hose Secure the drain hose so that it cannot slide off the edge of the wash basin Pass a piece of cord through the hose elbow and fix it to the wall or the tap Anti flood system For protection from water damage the dis
5. gelten die Garantiebedingungen der rtlichen Part ner Diese k nnen dort eingesehen werden Further after sales service agencies overseas In these countries our AEG agents own guarantee conditions are appli cable Please obtain further details direct Autres agences trang res assurant le service apr s vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont valables Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condiciones de nuestros representantes locales las cuales pueden ser consultadas all mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei partner locali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes paises s o v lidas as condi es de garantia dos concession rios locais podendo a ser consultadas Tov bbi vev szolg lati irod k k lf ld n Ezekben az orsz gokban a mi AEG vev szolg latainkn l saj t j t ll si felt telek alkalmazhat k A tov bbi adatokat k rj k k zvet len l szerezz k be Servisne sluzbe Na garancijskem listu boste na li seznam poobla enih servisnih slu b AEG 39 40 U A E Abu Dhabi Universal Trading Company P O Box 43 99 Tel 6335331 Service Center 6733974 Egypt Middle East Commercial Center 4 Salah El De
6. in transport Do not under any circumstances connect an ap pliance that is damaged In the case of damage please contact your supplier Never use the dishwasher if the mains cable water inlet or drain hose are damaged or if the control panel work top or plinth area are damaged such that the inside of the appliance is freely accessible Always plug the mains plug into a correctly installed shockproof socket Permanent connection a permanent connection must only be in stalled by a trained electrician Prior to using the appliance for the first time ensure that the rated voltage and type of supply on the rating plate match that of the sup ply where the appliance is to be installed The fuse rating is also to be found on the rating plate Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through overheating he dishwasher s cable must only be replaced by the Customer Care Department or a registered electrician A water inlet hose with safety valve must only be replaced by the Customer Care Department Installing the dishwasher e The dishwasher must be installed on a firm floor and adjusted to en sure that it is stable and level in all directions e To compensate for unevenness in i the floor and to match the height of the appliance to that of sur rounding units extend the thread ed feet using a screwdriver e The drain hose inlet hose and mains ca
7. the salt dispenser with water dispenser opening Fill the dispenser with special salt the capacity of the dispenser is ap prox 1 0 1 5 kg depending on the size of the grains Do not overfill the dispenser If water overflows when filling up with special salt this is completely harmless Clean away any salt remnants from the dispenser opening Screw the lid back on in a clockwise direction Run a dishwashing cycle after filling the salt dispenser with special salt This will wash away salt water and salt crystals that have been spilt Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and for the control indicator for special salt to go out Filling up with rinse aid With rinse aid the rinsing water drains away better and so you get smear free gleaming dishes and clear glasses If you do not use 3in1 detergent fill up with rinse aid Before using the dishwasher for the first time When the control indicator for rinse aid is illuminated on the control panel Use only special rinse aid for dish washers and no other liquid deter gents 1 Open the door The rinse aid compartment is locat x ad the inside of the dishwasher C gt 2 Press the release button on the rinse E aid compartment 3 Open the cover 4 Pour rinse aid in slowly right up to the broken max line this corresponds to a volume of ap pr
8. to be delayed lights up e g 6h if the cycle is to start in 6 hours Select dishwashing cycle The LED indicator for the programme selected and the indicator next to the number of hours will light up The dishwashing cycle will start automatically following a countdown of the hours set To change the time delay As long as the cycle has not yet started you can still change the setting by pressing the DELAY TIMER button Cancelling the delay timer Press the DELAY TIMER button repeatedly until none of the three time displays is lit The selected dishwashing cycle will begin immediately To change a dishwashing cycle As long as the cycle has not yet started you can still change the dish washing cycle First abort the dishwashing cycle then re set the time delay lastly select the new dishwashing cycle Switching off the dishwasher 1 Do not switch off the dishwasher until the indicator for the end of the dishwasher cycle is illuminated in the cycle progress display Press the ON OFF button All display indicators will go out 2 Turn off the water tap ij Carefully open the door Hot steam may escape Hot dishes are sensitive to knocks Therefore leave the dishes to cool for about 15 minutes before removing them You also get a better drying result Removing the dishes It is normal for the inner door and the dispensers to be damp Empty the lower basket first then the upper basket This way you avoid dr
9. 26 Fax 371 7845954 Lithuania Electrolux Lithuania Verkui 29 2600 Vilnus Tel 372 272 3326 Fax 372 272 3366 Malta ITC International Trading Company White House Building Mountbatte Street Blata L Bajda Tel 220644 Mauritius Happy World Centre Ltd P O 7 54 1 Chausee Street Port Louis Tel 25355 Namibia AEG NAMIBIA PTY LIMITED Jeppe Street Northern Industrial Area Windhoek Tel 061 21 6082 4 Fax 061 217838 New Zealand Monaco Corporation Ltd 10 Rothwell Avenue Albany Auckland 4399 Auckland 1 New Zealand Tel 0064 94156019 Fax 0064 94157070 Syria WATTAR CO P O Box 36109 Mazzeh Damascus Direct Phone 00963116132649 Fax 00963116119537 Iran ARIAN International Develop ment Co AEG Showroom Shariati Balatar as Safar Teheran Iran Phone No Showroom 021 285 513 4 Phone No Service 021 312 27 67 8 Poland Electrolux Poland Sp zo o ul Domaniewska 41 02 034 Warszawa tel 022 874 33 33 fax 022 874 33 00 Russia Electrolux Russia Ltd 16 Olympiysky prospekt 129090 Moscow Tel 095 937 7837 Fax 095 926 5513 Israel Evis Ltd Tadiran Ampa Service 10 Gibonay Israel Street New Industrial Zone Netanya 42504 Israel Japan Electrolux Japan Ltd Domestic Appliances Department Maruzen Showa Warehouse Building Tookai 4 5 12 Ota ku 143 006 Tokyo Tel 0120 13 7117 Fax 03 3790 5257 Thailand Olympia Thai Tower 444
10. Consult your plumber if the water pres 1 bar 210 N cm2 100 kPa sure is less than 1 bar If the water pressure is greater than 10 bar a pressure reduction valve must be used available from your dealer Highest permitted water pressure 10 bar 2100 N cm2 1 MPa Connecting the inlet hose N The water inlet hose must not be kinked crushed or entangled when it is being connected Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch The inlet hose is fitted with either a plastic or a metal nut Only tighten the nut hand tight Then do a visual check for water tightness Make sure that the tap is not dripping liJ So that access to the tap in the kitchen is not restricted by the use of the dishwasher we recommend installing an additional tap or fitting a T branch to the existing tap If you need a longer water inlet hose than that supplied the following VDE approved complete hose sets are to be used These are available from your local dealer Hose kit WRflex 100 Code 911 239 034 Hose kit WRflex 200 Code 911 239 035 36 Water drainage Drain hose N The drain hose must not be kinked crushed or entangled Connecting the drain hose Maximum permitted height 1 metre Minimum required height 40 cm above the bottom edge of the ap pliance Extension hoses Extension hoses are available from your dealer or from our
11. FAVORIT 40730 Dishwasher User information E 2o E m 7 5 0 ES S So Dear customer Please read this User Information carefully and keep it to refer to at a later date Pass this User Information on to any subsequent owner of the appli ance The following symbols are used in the text N Safety instructions Warning Notes that concern your personal safety Attention Notes that show how to avoid damage to the appliance il Useful tips and hints Fe Environmental information Contents Operating Instructions ai 4 SL 4 Diagram of appliance cece eee eee eens 5 Control panel wea A DRE gag Ned ed ga 5 Prior to using for the first time eee ees 7 Setting the water softener cee eee 7 Adding special salt 9 Filling up with rinse aid isses 10 In daily se ici Cor EE erg Race 12 Loading cutlery and dishes cece cece eter eet eee ees 12 Adjusting the height of the upper basket 15 Adding detergent uiuere an thee ieee equ od eee IE bee 16 Using 3in1 detergents 0 cece cece cece tenet teenies 17 Selecting the dishwashing cycle Cycle Table 18 Starting a dishwashing cycle 0 eee eee 20 Setting the Delay Timer pramana dr hued de Were MOS ador 21 Switching off the dishwasher 002s 21 Care and cleaning
12. Rachadapiser Road Samsennok Huaykwang 10320 Bangkok Thailand Tel 006625136111 Fax 006625136334 Hungary Electrolux Lehel KFT Erzs bet Kir lyn tja 87 1142 Budapest Tel 00361 467 3200 Malaysia Arzbergh Engineering No 49A B Jalan Petaling Utama 7 4600 Petaling Jaya Tel 3 795 1084 Fax 3 795 1082 Singapore Group Pte Ltd 833 Bukit Timah Road Unit no 01 11 Royalville 279887 Singapore Tel 0065 64638484 Fax 0065 64638488 Slovakia Rep Electrolux Slovakia S R O Seberiniho 1 821 03 Bratislava Tel 02 4333 4322 4355 Fax 02 4333 6976 Saudi Arabia Awad Badi Nahas Est Shara Siteen Jeddah 21463 Phone 6646583 Alia Trading Co Mecca Road Riyadh 11491 Phone 4645977 Slovenia Electrolux Slovenia D O O Traska Ul 132 1000 Ljubljana Tel 61 1234 137 Fax 61 1234 238 South Africa AEG Pty Ltd 55 12th Road P O Box 1 02 64 Kew Johannesburg 2000 Tel 8069111 41 42 Service In the event of technical faults please first check whether you can remedy the problem yourself with the help of the operating instruc tions section What to do if If you were not able to remedy the problem yourself please contact the Customer Care Department or one of our service partners In order to be able to assist you quickly we require the following information X A Model description Product number PNC Serial number S No for numbers se
13. Today s detergents for dishwashers are almost exclusively low alkaline concentrated detergents with natural enzymes in tablet or powder form Using 50 C dishwashing cycles in conjunction with these concentrated detergents reduces pollution and is good for your dishes as these dish washing cycles are specially matched to the dirt dissolving properties of the enzymes in concentrated detergents It is for this reason that us ing 50 C dishwashing cycles in conjunction with concentrated deter gents can achieve the same cleaning results that can otherwise only be achieved using 65 C cycles Detergent tablets Detergent tablets from different manufacturers dissolve at different rates For this reason some detergent tablets do not attain their full cleaning power during short cycles Therefore please use dishwashing cycles with pre wash when using detergent tablets Using 3in1 detergents These products are detergents with a combined cleaning rinsing and salt function If you want to use 3in1 products There is no need to fill up with special salt or rinse aid Set the water softener to water hardness range Set the rinse aid dosage to 1 Before the start of the dishwashing cycle put 3in1 detergent in the de tergent dispenser If you do not want to use 3in1 products any more If you want to stop using 3in1 products please do the following Fill up the dispensers for salt and rinse aid again e Switch the water softe
14. ator timer Programme progress 1 2 display 1 INTENSIVE DELAY 70 O TIMER Q 3h0 D MAIN WASH 6hD 0 DRYING ah MINA ER ENERGY 9h0 BEND 30 MINUTES O SAVING 50 O NORMAL O SALT 50 0 RINSE AID 2 Function but ton 3 Programme buttons Control indicators The Programme buttons are used to select the desired dishwashing cy cle Function buttons In addition to the pre set dishwashing cycle the following functions can also be set using these buttons Function button 1 Sets the water softener Function button 2 not programmed Function button 3 not programmed Programme progress display The current stage of the programme is always shown in the programme progress display The control indicators have the following meanings SALT Y Refill with special salt RINSE AID Y Refill with rinse aid 1 These control indicators are never illuminated while a dishwashing cycle is running Prior to using for the first time il If you wish to use 3 in 1 detergent First read the section Using 3in1 detergents Do not fill up with special salt or rinse aid If you do not use 3in1 detergent before using for the first time 1 Set the water softener 2 Fill up with special salt for water softeners 3 Fill up with rinse aid Setting the water softener The water softener must be set manually and electronically 5 To avoid scale deposits on the dishes an
15. ble must be laid so that they are able to move freely within the plinth area and so that they are not kinked or crushed when the dishwasher is in position e The dishwasher must also be screwed tightly to the work surface or to the adjoining units This is essential to ensure the dishwasher does not tip up 33 AN ij 34 Unscrew the screws from the elbows Push the appliance s worktop back Lift the worktop at the front 3 and Free standing appliances If the dishwasher is installed directly next to a cooker a heat insulat ing non flammable panel laminated with aluminium foil on the side next to the cooker must be fitted flush with the top edge of the work surface depth 57 5 cm If the appliance is built in under a kitchen work surface the worktop supplied with the dishwasher can be removed in the following way at the rear 1 wards about 1 cm 2 remove it If the dishwasher is later used as a free standing appliance the work surface supplied with it must be re mounted The plinth on free standing appliances is not adjustable Connecting the dishwasher Connecting to the water supply e The dishwasher can be connected to cold and hot water supplies up to max 60 C e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure
16. d in the dishwasher the dishes must be washed with soft water i e water with a low lime content The water softener must be set according to the table to the water hard ness in the area where you live Your local water company will be able to give you information about the water hardness in your area The dishwasher must be switched off Setting manually 1 Open the dishwasher door 2 Remove the lower basket from the dishwasher 3 Turn water hardness dial on the left wall of the dishwasher interior to O or 1 see table Setting electronically 1 Press the ON OFF button If indicators for the programme buttons are lit a dishwashing cycle is activated The cycle must be deactivated Press function buttons 2 and 3 simultaneously for approx 2 seconds All additional wash programme button indicators will go out 2 Press function buttons 2 and 3 simultaneously and keep them pressed The LED indicators for function buttons 1 to 3 will flash 3 Press function button 1 The LED indicator for function button 1 will flash The LED indicator for the end of the dishwashing cycle will flash simul taneously The number of times that the LED indicator for the end of the dish washing cycle flashes corresponds to the hardness setting This sequence of flashes is repeated several times with a 3 second pause in between 4 Pressing function button 1 increases the hardness setting by 1 degree Exception
17. e rating plate Type of fault Any error messages displayed by the appliance So that you have the necessary reference numbers from your appliance at hand we recommend that you write them in here Model description Pee Meshes SANG 43 E From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausgerate GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de Copyright by AEG 822 961 618 00 290305 03 Subject to change without notice
18. glass Steel items that rust Wooden boards platters Items made from synthetic ma terials are of limited suitability Only wash stoneware in the dishwasher if it is specifically marked by the manufacturer as being dishwasher safe Glazed patterns may fade if washed very fre quently in the dishwasher Silver and aluminium parts have a tendency to discolour during washing Food remains e g egg white egg yolk and mustard often cause discoloration and staining on silver Therefore always clean food residues from silver immedi ately if it is not to be washed straight after use Glass can become dull after a large number of washes Before loading the dishes you should Remove the worst of the food residues Soak pans with burnt on food residues When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load bowls cups glasses pans etc with the opening downwards so that water cannot collect in them Dishes and items of cutlery must not lie inside one another or cover one another To avoid damage to glasses they must not touch one another Don t put small items e g lids in the baskets for the dishes but in the cutlery basket so that they can t fall through the holes Loading cutlery Warning Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk
19. hardness setting 1 follows hardness setting 10 5 When the hardness setting is correct press the ON OFF button The hardness setting is now saved If the water softener is set electronically to 1 this switches off the control indicator for special salt Water hardness Adjusting the hardness setting Number of flashes in ed in mmol I2 Range Manual Electronic 51 70 9 0 12 5 103 10 43 50 7 6 8 9 9 9 37 2 6 5 7 5 IV 1 8 29 36 5 1 6 4 7 7 23 8 4 0 5 0 6 6 19 22 3 3 3 9 5 5 15 8 2 6 2 4 4 11 14 1 9 2 5 9 3 3 4 10 0 7 1 8 1 11 2 2 1 below 4 below 0 7 l no salt 1 necessary 1 d German degree measure of the hardness of water 2 mmol l millimol per litre international unit for water hardness 3 On this setting the length of the dishwashing cycle may be slightly longer factory setting Adding special salt NO Ci Open the door and remove the low Screw open the lid on the salt dis Only when using the dishwasher Place the funnel supplied over the To decalcify the water softener it must be filled up with special salt Use only special salt suitable for domestic dishwashers If you do not use 3 in1 detergent fill up with special salt Before using the dishwasher for the first time When the control indicator for special salt is illuminated on the con trol panel er basket penser by turning it anti clockwise for the first time Fill
20. he anti flood system has been triggered The mains plug is not plugged in A fuse in the house s wiring system is defective For dishwasher models with a delay start timer A start time has been select ed The dishwashing compart ment is made from rust free stainless steel Rust spots in the dishwashing compart ment are due to rust parti cles from external sources rust particles from water pipes pans cutlery etc Remove such spots with a commercially available stainless steel cleaning product The whistling is not a cause for concern Remedy Turn off the tap and contact the Customer Care department Plug in mains plug Replace fuse If the dishes are to be washed immediately cancel the delay start Only wash cutlery dish es and pans that are suitable for dishwasher use Decalcify appliance with commercially available agents for cleaning dishwashers If the noises can still be heard after decalcifying the machine use a dif ferent brand of deter gent for washing cutlery and dishes If the dishwashing results are not satisfactory The dishes are still dirty e The wrong dishwashing cycle was selected e The dishes were loaded is such a way that the dishwashing water did not reach all items The baskets for the dishes must not be overload ed e The filters in the base of the washing compartment are dirty or incor rectly positioned e Good quality detergent was not used or
21. hwasher is equipped with a anti flood system In the event of a fault the safety valve in the water inlet hose immedi ately interrupts the supply of water to the appliance and the drain pump is activated In this way water can neither escape nor overflow The remaining water in the appliance is automatically pumped out Electrical connection Details about the voltage type of supply and the fuses required are to be found on the rating plate The rating plate is located on the right hand inner edge of the dishwasher door To isolate the dishwasher from the mains pull out the mains plug Important The plug must be accessible after the appliance has been installed Following installation live parts and insulated wiring must not be ac cessible to a test finger in accordance with DIN EN 60335 1 37 38 Connecting systems The water inlet hose drain hose and the mains cable must all be con nected to the side of the dishwasher as there is no space for them be hind the appliance 2 connection pieces 45 or doublevalve r water r waterinlet straight outer 19 mm drainage length 30 mm A 2 i os v N p ap fi a water mains water mains socket mains cable inlet cable drainage Guarantee Customer Service Weitere Kundendienststellen im Ausland In diesen L ndern
22. in St 2nd floor Heliopolis Kairo Egypt Tel 2024181719 Australia The Andi Co Group 1 Stamford Road Oakleigh VIC 3166 Tel 03 9569 1255 Fax 03 9569 1450 www andico com au Bahrain Arabian Gulf A A Zayani amp Sons P O Box 9 32 Bahrain Tel 17311124 Bulgaria Electrolux Bulgaria E 0 0 D 91 Levski Blvd 1000 Sofia Tel 2 806676 Fax 2 980 5276 Cyprus Hadjikyrlakos amp Sons Ltd Prodromou 121 P O Box 21587 Nicosia 1511 Service Telephones Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Estonia Electrolux Estonia Ltd Mustam e tee 24 EEO006 Tallinn Tel 372 6 650 090 Fax 372 6 650 092 Hong Kong Dah Chong Hong Ltd 20 Kai Cheung Road Kowloon Bay Kowloon Hong Kong Tel 0085222621620 Fax 0085227550333 Jordan Jordan Household Supply Co Ltd P O Box 3 68 Amman Tel 69 70 50 Canada EURO LINE Appliances 2150 Winston PARK Drive 20 Oakville Ontario L6H 5V1 Tel 905 829 3980 Fax 905 829 3985 Korea South Core Incorp 3 F Chewoo Bldg 200 Nonhyun Dong Kangnam Ku 135 010 Seoul Telefon 82 2 549 89 61 Croatia Electrolux D O O Suplova 7 10000 Zagreb Tel 161 19512 Fax 1 61 19513 Kuwait Arabian Gulf Ali Al Ghanim Est P O Box 21540 Safat Tel 4822190 Fax 4820116 Lebanon Adib amp Assaferi P O Box 539 Tripoli Latvia Electrolux Latvija Ltd Kr Barona ela 130 2 Riga LV 1012 Tel 371 73136
23. ipping water from the upper basket onto dishes in the lower basket 21 Care and cleaning IN Do not use furniture care products or aggressive cleaners When necessary clean the dishwasher s controls with a soft cloth and clean warm water Occasionally check the internal dispensers door seal and water inlet filter if fitted for dirt and clean them if necessary Cleaning the filters i The filters must be regularly checked and cleaned Dirty filters will spoil the wash results 1 Open the door and remove the lower basket 2 Turn the handle about 1 4 of a turn anticlockwise A and remove the fil ter system B 3 Grasp the grip hole on the fine filter 1 and remove it from the micro fil ter 2 4 Clean all filters thoroughly under running water 22 5 Remove the flat filter 3 from the base of the washing compartment and clean both surfaces thoroughly 6 Re insert the flat filter 7 Place the fine filter in the micro fil ter and fit the two together 8 Insert the filter system in place and lock it by turning the handle clock wise as far as it will go Ensure that the flat filter does not protrude above the base of the washing com partment Under no circumstances may the dishwasher be used without its filters Cleaning the spray arm jets Regularly check the jets in the spray arms for blockages When cleaning is necessary remove spray arm from the fixture a
24. lt message Malfunction Possible cause Remedy The tap is blocked or furred with lime scale Clean tap The tap is turned off Turn the tap on The filter where present in the threaded hose fitting on the tap is blocked The programme indicator for the selected dishwashing cy cle is flashing the indicator for the end of Cancel the dishwashing the dishwashing cycle is cycle see chapter flashing in rhythm 1 short Starting a dishwashing light signal with approx 3 cycle second pause in between clean filters see chap Problems with water inlet ter Cleaning the filters then start the dishwash ing cycle again Clean the filter in the threaded hose fitting Filters in the base of the washing compartment are blocked Water inflow hose has not been correctly positioned cup uid The programme indicator for The sink outlet is blocked Clean out sink outlet the selected dishwashing cy cle is flashing the indicator for the end of the dishwashing cycle is Water drain hose has not flashing in rhythm 2 short been correctly positioned light signals one after anoth er Check hose installation 26 Malfunction the indicator for the end of the dishwashing cycle is flashing in rhythm 3 short light signals one after anoth er The cycle is not starting Rust spots are visible in the dishwashing compartment A whistling noise can be heard when washing dishes Possible cause T
25. nd clean jets with a pointed object wire or needle Then rinse out the spray arm using a strong jet of water Do not damage the jet opening Upper basket spray arm To remove upper basket spray arm tilt it down hard 2 Clean spray arms jets 23 24 3 Place cleaned upper basket spray arm back in position against the cm E ing piece press the two together firmly until you feel them snap into place Bottom spray arm 1 To remove bottom spray arm pull it upwards out of its catch 2 Clean spray arm jets 3 Place bottom spray arm back in posi tion against connecting piece and press down firmly until you feel it snap into place ME YS E e qus p am What to do if Remedying small malfunctions If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table please consult this to find out how to remedy the fault After remedying the fault that is flashing in the first or second rhythm in the programme progress display press the button for the dishwashing cycle that had already started The cycle will continue In the case of other fault messages Cancel the dishwashing cycle Switch the appliance off and on again Select dishwashing cycle If the fault is displayed again please contact the Customer Care De partment and inform them of the fau
26. ndanger life e Dishwasher detergents can cause chemical burns to the eyes mouth and throat Could endanger life Comply with the safety instructions of the dishwasher detergent manufacturer e The water in the dishwasher is not for drinking Risk of chemical burns General safety e Repairs to the dishwasher are only to be carried out by qualified serv ice engineers When the dishwasher is not being used switch it off and shut off the water tap e Never unplug the appliance by pulling on the cable Always pull the plug e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves e Never sit or stand on the open door e f the dishwasher is located in a room where there may be a frost re move the connection hose from the tap after each use of the dish washer Diagram of appliance Top Spray Nozzle Upper basket spray arm and floor spray arm Water hardness dial Dispenser for special salt Dispenser for detergent E Dispenser for rinse aid Rating plate Filters Control panel 0 DRYING 0 END INTENSIVE peur IO DELAY 9m O MAIN wast sawal O salt O NORMAL 1 Usar so 0 RINSE AID ON OFF button The ON OFF button is used to turn the dishwasher on and off Function buttons Set delay End of cycle indic
27. ner to the highest setting and perform up to three normal cycles without loading any dishes hen set the water softener to the water hardness in your area 17 Selecting the dishwashing cycle Cycle Table Programme Consumption sequence values n Dishwashing Suitable Type of is cycle for soiling E E 95 E de e 2 ET SED cedes al ese eee E e sse e o t EE E E53 E RES 22 heavily soiled cM INTENSIVE dura dried on food re e doal SFs 70 N mains in particular o y protein and starch SS eee 30 MINUTES EA eee LILLE 60 2 E normally soiled E o Dinner serv a o gt Msc ice and normally soiled ex en Een ex Een s 0 B0 cookware a a Dinner serv ice and 3 8 ENERGY cookware VO EI ed Ne pes cw Ro Lar Mass SAVING 50 2 temperature y 29 me en sensitive ES crockery 1 The consumption values were obtained under standardised conditions They depend on how full the baskets for the dishes are Variations are therefore possible in practice 2 When using this cycle only load the dishwasher half full 3 Test programme for Test Institutes 18 Selecting a programme When your dishes look like this select an intensive programme a normal or energy saving pro gramme a short programme e g 30 minute programme Starting a dishwashing cycle 1 Check that the spray arms can turn freely 2 Turn the water ta
28. ng of elec trical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed infor mation about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Warning When your appliance has finished its working life remove the plug from the socket Cut off the cable and plug and dispose of them Break the door lock so that the door no longer shuts This prevents chil dren from trapping themselves inside and endangering their lives Technical data Capacity 12 place settings including serving dishes Permitted water pres i 1 10 bar 210 100 N cm 0 1 1 0 MPa sure 230 V 10 A also see the rating plate on the right hand side Electrical conne e Hone of the dishwasher s interior door Dishwasher Free standing appliances Dimensions 850 x 598 x 598 H x W x D in mm Max weight 54 kg C This appliance conforms with the following EU Directives 73 23 EEC dated 19 02 1973 Low Voltage Directive 89 336 EEC dated 03 05 1989 EMC Directive inclusive of Amending Directive 92 31 EEC 93 68 EEC dated 22 07 1993 CE Marking Directive 29 30 Notes for Test Institutes Testing in accordance with EN 60704 must be carried o
29. ox 140 ml when full 5 Press the lid shut until it clicks into place 6 Wipe up any spilt rinse aid with a cloth Otherwise there will be too much foam when rinsing Setting the amount of rinse aid required Only change the amount dispensed if smears milky spots reduce the amount or dried on water spots increase the amount can be seen on glasses and dishes See section If dishwashing results are not satisfac tory The dosage can be set from 1 6 The dosage is pre set to 4 in the factory 1 Open the dishwasher door 2 Press the release button on the rinse aid compartment 3 Open the cover 4 Set the dosage level 5 Press the lid shut until it clicks into place 6 If rinse aid has leaked out wipe it away with a cloth In daily use Loading cutlery and dishes AN 12 Sponges cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher Plastic and Teflon coated dishes and pans tend to retain water droplets These dishes and pans therefore do not dry as well as those made of china and stainless steel For washing in the dishwasher the following cutlery dishes pots and pans are not suitable Cutlery with wooden horn china or mother of pearl han dles Plastic items that are not heat resistant Older cutlery with cement that is sensitive to temperature Dishes or cutlery with glued parts Pewter or copper items Lead crystal
30. p on fully 3 Close the door 4 Press the ON OFF button 5 Select the desired cycle The programme display lights up One or two lights will flash in the programme progress display The selected cycle will begin after approximately 3 seconds Interrupting or aborting a dishwashing cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary Interrupting the dishwashing programme by opening the dishwash er door DN Hot steam may escape when the door is opened There is a risk of scald ing 1 Open the door carefully The dishwashing cycle will stop 2 Close the door The cycle will continue Aborting the dishwashing cycle 1 Press function buttons 2 and 3 and keep them pressed The programme display for the current cycle will flash for several sec onds and then go out 2 Release the function buttons The dishwashing cycle has been can celled 3 11 you want to start a new cycle check whether there is any detergent in the dispenser 5 Turning off the dishwasher will only interrupt a selected dishwashing cycle not cancel it The cycle will recommence after turning the dish washer back on again 20 Setting the Delay Timer N Using the delay timer you can delay the start of a dishwashing cycle for 3 6 or 9 hours Press the ON OFF button Press the Delay Timer button repeatedly until the indicator next to the number of hours for which the start of the dishwashing cycle is
31. too little was used e In the case of scale deposits on the dishes The special salt dispenser is empty or the water softening system has been incorrectly set e The drain hose is incorrectly positioned e Pollutants from the water in the dishwasher can block the jets in the spray arms You have the option of removing the spray arms from their fixture for cleaning see section Care and Cleaning The dishes do not dry and are not shining e Poor quality rinse aid was used The rinse aid dispenser is empty There are smears streaks milky spots or a shiny bluish coating on glasses and dishes e Lower rinse aid dosage There are dried water drops on the glasses and dishes e Increase rinse aid dosage e The detergent may be the cause Contact the detergent manufactur er s customer advice centre Glass corrosion Contact the detergent manufacturer s customer advice centre 27 Disposal Go 28 Packaging material The packaging materials are environmentally friendly and can be recy cled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities Old appliance The symbol x on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycli
32. ut with the appliance fully loaded and using the test cycle see Cycle Table Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively and using the test cycle see Cycle Table Full load Half load 12 place settings 6 place settings including serving including serving dishes dishes leaving alternate positions in the rack free Amount of detergent required 5g E 25g Type B 20g Type B Rinse aid setting 4 Type III 4 Type III Example loading arrangements Upper basket e dl If there are cup racks in place on the lefthand side or the cutlery tray is in place re move them Lower basket with cutlery basket Cutlery basket 1 TT m 6 17 7 TY SSS hill a h Ka Bo MINUS A 22222 REF If there are cup racks in place on the lefthand side or if beer glass holders are in place remove them 31 32 Installation and connection instructions AN Safety information for the installation Only transport the dishwasher in an upright position otherwise salt water may run out Before using the dishwasher for the first time check for any damage caused
Download Pdf Manuals
Related Search