AEG 2460 D Cooktop User Manual
Contents
1. Turn the hood on a few minutes before you start cooking then you will get an underpressure in the kitchen It should be left on after cooking for about 15 minutes or until all odours have disappeared The control switches are located on the units front panel Main switch hood on off Start and choice of motor speed 1 2 3 1 2 Indicates speed 1 LED Indicates speed 2 LED Indicates speed 3 LED Indicates Intensive speed LED Intensive speed on off The Intensive speed runs for 5 minutes If the hood is on when the Intensive speed is activated the hood revert to previous speed after 5 minutes If the hood is off when the Intensive speed is activated the hood will automaticly be turned off after 5 minutes To interrupt the Intensive speed press button A or B Light off Light on PPIP f i B CDE Should the hood or the controls fail to operate disconnect the power supply for at least 5 seconds then turn the hood back on again 60 Maintenance and care e The hood must always be disconnected from the mains power supply before beginning any maintenance work Metal grease filter e The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used either in the external evacuation or internal recycling function Attention the metal grease filters must be removed and washed either by hand or in the dishwasher every four weeks Open the metal grease2. filter e First push the metal grease filter stop backwards then extract the filter pulling downwards Fig 3 Hand washing Soak grease filters for about one hour in hot water with a grease loosening cleaner then rinse off thoroughly with hot water Repeat the process if necessary Refit the grease filters when it are dry Dishwasher machine Place grease filters in dish washer Select most powerful washing programme and highest temperature at least 65 C Repeat the process Refit the grease filters when it are dry When washing the metal grease filter in the dishwasher a slight discoloration of the filter can occur this does not have any impact on its performance Clean the inner housing using a hot detergent solution only never use caustic detergents abrasive powders or brushes 61 Carbon filter 62 The activated carbon filter should only be used if you want to use the hood in its filtering function To do this you will need an original AEG activated carbon filter see special accessories Cleaning replacing the carbon filter Unlike other carbon filters the LONGLIFE carbon filter can be cleaned and reactivated At normal use the filter should be cleaned every second month The best way to clean the filter is in the dishwasher Use normal detergent and choose the highest tempera ture 65 C Wash the filter separately so that no food parts gets stuck on the filter and
3. reduce the performance and increase the noise levels of the extractor hood Introduction Extractor version The hood is supplied in the extractor version but it can also be used in the filter version by inserting an activated charcoal filter Special accessory To do this use an original AEG activated charcoal filter see Special accessories The air is discharged to the outside through a pipe which must be fitted to connection flange A Fig 1 For the extractor version this pipe must have a diameter of 150 mm Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof it is possible to use the 150 125 mm reduction flange provided In this case the hood will be slightly more noisy Fig 1 Filter version The air is filtered through an activated charcoal filter and returned to the kitchen through the top grill of the outlet pipe When the hood is used in the filter version it must be fitted with an original AEG KF20 activated charcoal filter see Special accesso ries Fix the deflector using two screws 3 5x6 5 mm Fig 2 Optionally the position of the chimney elements can be changed When using the hood in the filter version the chimney must be fixed at the top with the air outlet grill at the side 59 Fig 2 Hood Operation onm e Best results are obtained by using a low speed for normal conditions and high speed when odours are more concentrated
4. 3000 D 3010 D Dunstabzugshaube Afzuigkap Hotte aspirante Cooker Hood Montage und Gebrauchsanweisung Installatie en gebruiksaanwijzing Manuel de montage et d utilisation Operating and Installation Instructions Contents Safety warnings for user for kitchen unit installer Introduction Extractor version Filter version Hood operation Maintenance and care Metal grease filter Open the metal grease filter Carbon filter Changing the light bulb Cleaning Special accessories Technical assistance service Guarantee conditions Service Technic Details Installation Electrical connection Safety warnings for the electrician Wall unit mounting 56 57 59 60 61 62 63 64 65 67 68 69 Safety warnings for user Always cover lighted elements to prevent excess heat from damaging the appliance In the case of oil gas and coal fired cookers it is essential to avoid open flames Also when frying keep the deep frying pan on the cooker top cooker under careful control The hot oil in the frying pan might ignite due to overheating The risk of self ignition increases when the oil being used is dirty It is extremely important to note that overheating can cause a fire Never carry out any flamb cooking under the hood Always disconnect the unit from the power supply before carrying out any work on the hood including replacing the light bulb take the cartridge fuse out of the fuse hold
5. cm 171 m h 268 m h 291 m h 435 m h 118 m h 176 m h 201 m h 267 m h 67 Electrical connection Safety warnings for the electrician 68 Before connecting the appliance to the power supply check that the voltage indicated on the rating plate corresponds to the mains power supply available Appliances fitted with a plug can be connected to any standard power socket within easy access Should it be necessary to provide a fixed connection the hood must only be installed by an electrician authorised by the local electricity board When installing an omnipolar disconnector with a distance of at least 3 mm between contacts must be provided This disconnector may be for example a switch fuses plug fuses must be removed from the fuse box fault current switches and remote switches with a distance of over 3 mm between contacts The manufacture declines all responsibility for malfunctions resulting from failure to comply with the above instructions If the power socket is applied directly above the hood this gives two advantages 1 the socket is not visible 2 the appliance can be disconnected at need merely be removing the plug Electrical connection 220 240 V by means of fixed power cable with plug Fixed connection of the appliance must only be carried out by an au thorised electrician Wall unit mounting Fig 6 First decide which functioning version is better for you If you decide to us
6. d in correctly before contacting the technical assistance service Fig 5 63 Cleaning e Warning always disconnect the hood from the mains power supply before cleaning it Never insert pointed objects in the motor s protective grid e Wash the outside surfaces using a delicate detergent solution Never use caustic detergents or abrasive brushes or powders e Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents e It is extremely important to clean the unit and change the filters at the recommended intervals Failure to do so will cause grease deposits to build up that could constitute a fire hazard Special accessories Carbon filter KF20 E Nr 942 120 600 Technical assistance service 64 You are welcome to telephone our technical assistance service see list of technical assistance centres whenever you need information or in the unlikely event of a fault When calling please be ready to specify 1 The model code number 2 The serial number E Nr 3 The manufacturing number F Nr This information is shown on the registration plate inside the unit behind the grease filter We reserve the right to change specifications and colours as a result of our policy of continuing technological development Guarantee conditions Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance 1 The guarantee is valid for 12 months comme
7. e provided with dimensions that are approximately the same as the outlet hole National and regional building regulations impose a number of restrictions on using hoods and fuel burning appliances connected to a chimney such as coal or oil room heaters and gas fires in the same room Hoods can only be used safely with appliances connected to a chimney if the room and or flat air environment combination is ventilated from outside using a suitable ventilation hole approxi mately 500 600 cm large to avoid the possibility of a depression being created during operation of the hood If you have any doubts contact the relevant controlling authority or building inspector s office Since the rule for rooms with fuel burning appliances is outlet hole of the same size as the ventilation hole a hole of 500 600 cm which is to say a larger hole could reduce the performance of the extractor hood If the hood is used in its filtering function it will operate simply and safely in the above conditions without the need for any of the aforementioned measures When the hood is used in its extractor function the following rules must be followed to obtain optimal operation short and straight outlet hose keep bends in outlet hose to a minimum never install the hoses with an acute angle they must always follow a gentle curve only keep the hose as large as possible 150 mm min Failure to observe these basic rules will drastically
8. e the hood in exhausting version we suggest to position the upper section of the chimney so that the oulet slots are not visible once installation has ended on the contrary if is decided to use the hood in recycling version BE SURE that the side with slots is up See also A B C sequence on on Fig 6 Insert the frame that holds controls grease filter and lamps in the mo tor housing using proper rails and fix each other with two 3x9 screws 1 2 3 Sign the wall with a center line this will aid mounting procedure 4 position the template so that the mid line printed on the template mat ches with the center line previously signed the lower side of the temp late corresponds to the lower side of the hood once mounted 5 Drill two holes 8mm and fix the support bracket with two wall plugs and screws 6 Hang the hood 7 adjust its position 8 9 and from the inside of the hood sign one point for definitive fixing 10 remove the hood and drill an hole 8mm 11 fit a wall plugs hang the hood again and fix it definitively with a screw 12 Drill two holes 8mm on the upper side close to the ceilling 13 fit two wall plugs and fix the chimney support with two screws 14 In case the hood is to be used in Recycling version mount the deflector F on the chimney support with four screws 2 9x6 5 and fit an exhausting pipe 15 to connect deflector to the outlet hole B of the hood In case the hood is to be used in exhausting ve
9. er or switch off the automatic circuit breaker It is very important to clean the hood and replace the filter at the recommended intervals Failure to do so could cause grease deposits to build up causing a fire hazard for kitchen unit installer When used as an extractor unit the hood must be fitted with a 150mm diameter hose Falls ein Abluftrohr in Wand oder Dach mit einen Durchmesser von 125 mm schon besteht kann der mitgelieferte Reduzierstutzen 150 125 mm verwendet werden Zusammen mit dem Reduzierstutzen kann der Ablaufschlauch 125 montiert werden When installing the hood make sure you respect the following minimum distance from the top edge of the cooking hob ring surfaces electric cookers 600 mm gas cookers 650 mm coal and oil cookers 700 mm min 57 58 The national decree on fuel burning systems specifies a maximum depression of 0 04 bar in such rooms The air outlet must not be connected to chimney flues or combustion gas ducts The air outlet must under no circum stances be connected to ventilation ducts for rooms in which fuel burning appliances are installed It is advisable to apply for authorization from the relevant controlling authority when connecting the outlet to an unused chimney flue or combustion gas duct The air outlet installation must comply with the regulations laid down by the relevant authorities When the unit is used in its extractor version a sufficiently large ventilation hole must b
10. later causes bad odours To reactivate the carbon the filter should be dried in an oven for 10 minutes with a temperature of maximum 100 C After approximately three years of use the carbon filter should be replaced with a new as the odour reduction capacity will be reduced Mounting Remove the frame i which supports the filter h by unscrewing it from the hood g Fig 4 Insert the coal mattress inside the frame and put all parts back in their place To dismount proceed in reverse order Always specify the hood model code number and serial number when ordering replacement filters This information is shown on the registration plate located on the inside of the unit The activated carbon filter can be ordered from the AEG technical assistance service Afb 4 AN Warning Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard You are therefore strongly recommended to follow these instructions The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations Changing the light bulb Disconnect the cooker hood from the main supply Remove the lamp cover use a screw driver as a lever Fig 5 Replace the old bulb with a new one of the same type Remount the lamp cover If the light does not come on make sure the bulb has been inserte
11. ncing when the appliance is handed over to the first retail purchaser which must be verified by purchase invoice or similar documentation The guarantee does not cover commercial use 2 The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials The guarantee does not cover appliances where defects or poor performance are due to misuse accidental damage neglect faulty installation unauthorised modification or attempted repair commercial use or failure to observe requirements and recommendations set out in the instruction book This guarantee does not cover such parts as light bulbs removable glass ware or plastic 3 Should guarantee repairs be necessary the purchaser must inform the nearest customer service office manufacturer s service or authorised agent AEG reserves the right to stipulate the place of the repair i e the customer s home place of installation or AEG workshop 4 The guarantee or free replacement includes both labour and materials 5 Repairs carried out under guarantee do not extend the guarantee period for the appliance Parts removed during guarantee repairs become the property of AEG 6 The purchaser s statutory rights are not affected by this guarantee European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first pu
12. rchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products This guarantee relates to you an cannot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country 65 Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis Germany Nurnberg Italy Pordenone Sweden Stockholm UK Slough 66 33 0 44 62 29 29 49 0 911 323 2600 39 0 1678 47053 46 0 8 738 7910 44 0 1753 219899 Technic Details Dimensions Extractor version Height x Width x Depht in cm 660 1120 x8 Dimensions Filter version Height x Width x Depht in cm 755 1220 x Maximum absorbed power Motor absorption Lighting Lenght of the cable Fan powers speed speed in compliance with DIN 44971 m Extractor version Speed Filter version Speed 09 PO 77 Co N Flange 150 mm 98X x 500 898 x 500 210 W 1x 170W 2 x20 W 150
13. rsion then the deflector must not be mounted and fit an exhausting pipe 15 to connect outlet hole B of the hood to the outside Make electrical connection 16 but leave the hood disconnected from the home general electric panel Connect lamps and control panel to the motor housing 17 Insert the vapour catcher on the motor housing and fix it with four screws M4x35 18 Model 3010D has an additional part that can be mounted to the first part fixed on step 18 before or after this step choose the convenience fixing between this two parts must be done with four screws Fix the chimney first up 19a to the chimney support 19b then on the bottom 20a to the upper side of the frame 20b using four screws 2 9x6 5 Connect the hood the the home general electric panel and check if the hood work properly 69 HAN No N we re DIN KA W Fig 6 70 AEG Hausgerate GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de Copyright by AEG LI1M7B Ed 05 01
Download Pdf Manuals
Related Search