AC International UPP Network Card User Manual
Contents
1. lt MENU gt Continue until Select Net ID 001 gt lt UP gt Select Net ID 001 lt RIGHT gt Select Net ID 001 desired Select Pswd 0000 Select Pswd 1000 Select Pswd 1000 Paseword y lt ENTER gt V lt MENU gt 1 Add Device 2 Edit Device y lt ENTER gt v Select DevID 002 To desired Select DevID 001 UP gt Device ID lt UP gt I lt ENTER gt y Enter Setup Mode ly lt Set gt Add Device aa aay gid lt MENU gt or lt ENTER gt lt Device Added gt Net 001 Dev 001 If device is not found Err Device Fail Net 001 Dev 001 lt MENU gt y lt ENTER gt Add Device is used to add installed UPB devices to the UPB network If a device is not found 1 Make sure there is only one device in set up mode 2 Check the wiring to ensure the connections are proper and the wire nuts are on tight 3 Check the phase coupler to ensure it is properly installed and operational Pocket Programmer 1 Add Device Edit Device lt ENTER gt lt MENU gt y A 1 Add Device 2JEdit Device sa aa lt MENU gt Select DevID 001 Select DevID 002 To desired are aie Device lt ENTER gt lt y Select DevID 001 ELSE Err lt SAI UML gt Device Not Found lt ENTER gt If device is not found y lt MENU gt 1 ID A 2 Receive Links Jer Go to Edit Device A Sub Menu lt UP DOWN gt 1 ID 2 Receive Links A 4 lt2. 6 Delete Link Pocket Programmer 1 Access Network New Network 2 New Network lt DOWN gt lt MENU gt 1 Access Network 2 New Network lt ENTER gt lt MENU gt Model UPP New Network is used to create a UPB network by starting with a Network ID and Password The Network ID can be from 1 250 It is recommended to use a different Network ID for each installation The password is 4 hexidecimal characters 0 9 and A F Once the UPB network is created devices and Links may be added Nothing is stored in the UPP All data is stored in the devices as they are added UPB device must share the same UPB Network ID and password to communicate peer to peer Select Net ID 001 Select Net ID 002 To desired lt UP gt lt UP gt m Network ID lt ENTER gt Select Net ID 001 lt Search for Net gt lt MENU gt Select Net ID 001 Select Pswd 0000 lt ENTER gt y 1 Add Device 2 Edit Device lt MENU gt Continue until lt UP Select Net ID 001 _pigpr Select Net ID 001 iscia Select Pswd 1000 Select Pswd 1000 Password lt ENTER gt to Add Device See Add Device page lt DOWNb gt to scroll through this sub menu See Access Network Sub Menu Pocket Programmer Add Device 1 Access Network 2 New Network To existing Network y lt ENTER gt lt MENU gt cr A Select Net ID 001 Select Net ID 002 To desired os lt UP gt Network ID lt ENTER gt v Model UPP
3. lt ENTER gt Dim Enable YES lt UP DOWN gt Dim Enable NO lt Writing gt 3 Transmit Links 4 Options 3 Dim Enable 4 Def Fade Rate rd lt MENU gt Default Fade lt UP DOWN gt Snap to 1 hour ENTER gt Rate 3 3 seconds lt ENTER gt lt Writing gt lt UP DOWN gt L 4 Options 5 Advanced 4 Def Fade Rate 5 Status Report lt MENU gt lt MENU gt lt ENTER gt lt ENTER gt Status Reports N e ypipown gt Status Reports Y lt Writing gt Ul 1 Add Device 2 Edit Device 5 Status Report 6 Xmit Enable lt UP DOWN gt To select button Chien lt ENTER gt lt LEFT RIGHT gt 0 select YES or NO to enable or disable xmit lt UP DOWN gt Rkr Xmit Option SENTER 4 Button 1 NO lt Writing gt 6 Xmit Enable 7 Ad Del Enable lt MENU gt lt ENTER gt Add Delete Link Enable ON lt UP DOWN gt Add Delete Link lt Writing gt Enable OFF lt ENTER gt Vit 12 Pocket Programmer Model UPP 1 ID 2 Receive Links lt UPIDOWN Edit Device Advanced 1 ID 2 Receive Links A lt UP ER 2 Receive Links 3 Transmit Links 3 1 Xmit Type Transmit Type Transmit Type ee lt Writing gt lt UP DOWN gt gt lt ENTER gt ne dae lt ENTER
4. Enter Setup Mode lt MENU gt v Add Link 001 lt DOWN gt v lt UP DOWN gt 2 Edit Device To Select Device ID 3 View Device v lt ENTER gt ae lt Link Added gt l Add Link 001 3 View Device 4 Delete Device lt MENUs or lt ENTER gt y lt DOWN gt y 4 Delete Device 5 Add Link Device that is to have the Link added must be in Setup Mode This feature will work with multiple devices as long as all are in Setup Mode This will display even if no device was put in Setup Mode hence no Link added Model UPP 15 Pocket Programmer Delete Link 2 New Network lt ENTER gt lt MENU gt v Select Net ID 001 lt UP gt Select Net ID 002 lt UP gt To desired Network ID Yy lt ENTER gt v lt MENU gt Select Net ID 001 Select Pswd 0000 Continue until pep Select Net ID 001 lt RIGHT gt Select Net ID 001 desired Select Pswd 1000 Select Pswd 1000 Password lt ENTER gt lt v 1 Add Device 2 Edit Device M lt DOWN gt 1 Add Device 2JEdit Device lt DOWN gt v 2 Edit Device 3 View Device TE must be in Setup Mode s au This feature will work with multiple Device that is to have the Link deleted MENU 4 Enter Setup Mode y Oo 3 View Device To Select Device ID v 4 Delete Device J lt ENTER gt SENTERA ee lt DOWN gt zink Deleted This will display even if no y Delet
5. SMe cola el dm agree ies ee ee 3 j f a a FUNCTION The Pocket Programmer has an LCD display with 2 lines of 16 characters a diagnostic LED 7 buttons a polarized power connector and a DB 9 port Model UPP BUTTONS The buttons provide easy navigation through the Pocket Programmer s menus on the LCD display MENU Returns the display to the previous menu from any sub menu exits selection without writing to selected device UP and DOWN Provide movement through the menus and toggle through characters when editing a selection RIGHT and LEFT Provide movement across the display ENTER Enters a selected menu item Provides movement through selected menu item editable fields and executes commands and edits that are sent to the selected device or network Pocket Programmer FUNCTION Toggles the backlight on the LCD display LED The diagnostic LED operates just as the LED on the Computer Interface Module In Run CIM mode the Pocket Programmer exchanges UPB messages between the powerline and the connected computer or controller The indicator on the UPP will glow AMBER when powered flash RED when UPB messages are seen on the power line and flash GREEN when a UPB message is transmitted from the Pocket Programmer DB9 Port Connect a standard serial cable to an RS 232 port to use the Pocket Programmer as a Computer Interface Module The DB9 port may also be used to upgrade the firmware in t
6. Select Position lt UP DOWh gt 5 Device ID lt ENTER gt Device ID lt ENTER gt lt Writing gt 007 007 A lt k UP DOWN gt lt LEFT RIGHT gt UP ae tne Select Character Select Position 6 Mfg ID 0004 lt UP DOWN gt y 7 Product ID Read Only 000 005 A lt P gt SyFirmware Ver v04 15 Pocket Programmer Edit Device Sub Menu Receive Links NID Receive Links lt AE DID 2 Receive Links lt Ae 2 Receive Links 3 Transmit Links A tice ee 3 Transmit Links 4 Options Fr 4 Options 5 Advanced 1 Add Device 2 Edit Device lt MENU gt lt ENTER gt lt Reading Device gt 01 Link Lvl Rate 010 100 Def 02 Link Lvl Rate 000 Def lt MENU gt lt UP DOWN gt y lt ENTER gt Y 01 Link Lv Rate 010 100 Def lt ENTER gt 01 Link Lvl Rate 010 100 Def lt MENU gt y lt ENTER gt Y 01 Link Lv Rate 010 100 Def lt ENTER gt 01 Link Lvl Rate lt Writing gt lt UP DOWN gt Model UPP 16 Link Lv Rate 000 Def 10 Pocket Programmer ID 2 Receive Links A lt U Ho dg 1 ID Receive Links Model UPP Edit Device Sub Menu Transmit Links lt ENTER gt lt Reading Device gt lt UP DOWN gt y Transmit Links Super Toggler Super
7. gt UPB Noise lt 1il gt UPB Signal lt 087 gt lt MENU gt lt CIM Enabled gt lt MENU gt Set Contrast 070 UPB Noise View Run CIM Set Contrast Noise displays as bars Signal displays as unit less numbers between 001 and 100 Default is Message Mode UPStart will change to Pulse Mode To return to Message Mode press lt MENU gt and lt ENTER gt lt UP DOWN gt To select contrast level Model UPP 19 Pocket Programmer Model UPP Simply Automated Incorporated 5825 Avenida Encinas Suite 101 Carlsbad CA 92008 USA A Simply Technical Support www simply automated com or 800 630 9234 Automated 452 0031 0001 Rev A Revised May 16 2006 20
8. Main Menu 1 Access Network 2 New Network lt UP DOWN gt 1 Access Network 2 New Network lt UP DOWN gt 2 New Network 3 UPB Explorer lt UP DOWN gt 3 UPB Explorer 4 UPB Noise View lt UP DOWN gt 4 UPB Noise View 5 Run CIM lt UP DOWN gt 5 Run CIM 6 Set Contrast Model UPP Access Network Sub Menu Access Network 1 Access Network 2 New Network 1 Add Device ences lt MENU gt 2 Edit Device y lt UP DOWN gt Select Net ID 001 gt lt yp gt Select Net ID 002 jp LE saat etwor 1 Add Device y 2 Edit Device lt ENTER gt lt ah Y z NEN F Continue until lt UP DOWN gt Select Net ID 001 lt yp gt Select Net ID 001 epigr Select Net ID 001 das rad Select Pswd 0000 Select Pswd 1000 Select Pswd 1000 Password 2 Edit Device y 3 View Device lt ENTER gt y lt MENU gt lt UP DOWN gt 1 Add Device 2 Edit Device 3 View Device v lt ENTER gt to Add Device See Add Device page lt DOWN gt to scroll through this sub menu See Access Network Sub Menu 4 Delete Device lt UP DOWN gt 4 Delete Device 5 Add Link Access Network is used on an installed UPB network It is useful when viewing or editing devices Devices can be added or deleted Links may also be added or deleted The same functions are available in UPStart under the Device Link and Network menus lt UP DOWN gt 5 Add Link
9. Pocket Programmer Model UPP m Simply z rad incorporated UPB Pocket Programmer User Guide Pocket Programmer DESCRIPTION The Pocket Programmer model UPP provides many of the features of UPStart UPB configuration software in a portable hand held device The Pocket Programmer comes with a handy carrying case and AC power cord that plugs into any standard receptacle allowing communication to installed UPB devices The Pocket Programmer is intended for use by an installer who is familiar with UPStart and UPB products It virtually eliminates the need to have a PC with UPStart software and a Computer Interface Module CIM at every jobsite It makes configuring UPB devices from room to room quick and easy The UPP may be used instead of UPStart to provide initial configuration steps such as adding devices to a UPB network or disabling dimming allowing a newly installed switch to operate a fluorescent fixture It could also be used to program an entire UPB installation No data is stored in the UPP The UPB network and device programming is stored in each UPB device A UPB network that was configured with the UPP may be added to UPStart at any time by using the Network Discovery feature in UPStart The UPP has diagnostic tools that include a noise and signal meter and an explorer feature that reads and transmits UPB messages on the powerline In the Run CIM mode the Pocket Programmer may be used as a Computer Interface Modu
10. Toggler ER Super Toggler lt UP DOWN gt Vv 3 Transmit Links 01 Link 241 01 Link 242 Field rolls over v lt UP DOWN gt Options Super Toggler Super Toggler Range is 001 to 250 re 4 Options 01 Link 241 UP DOWN gt O1 Link 241 Choices as Down Button is pressed Advanced Super Toggler On Off Button Super Toggler Link Actuator v Toggle Button Drape Close lt MENU gt Super Multi Button Drape Open Multi Button Null Button Add Device 01 Link 241 Panic Button BtmSuperRocker 2 Edit Device lt Writing gt Bottom Rocker TopSuperRocker Top Rocker Indicator Off Dim Button Indicator On Bright Button Status Button On Button On Off Button Off Button ll Pocket Programmer Edit Device Options DID 2 Receive Links Model UPP Options vary from module to module They follow the selections in UPStart for each device gt lt ENTER gt 1 Faceplates A lt UP DOWN gt v 2 LED Options 1 ID To scroll 2 Receive Links lt DOWN gt 1 Faceplates A ase a 2 LED Options 2 Receive Links F i lt MENU gt lt ENTER gt F opiate ag MT ENTER Faceplate US selections LED Options To scroll lt MENU gt lt Writing gt lt ENTER gt lt UP DOWN gt through lt ENTER gt On GRN OFF RED Mroug selections lt UP DOWN gt 3 Transmit Links 2 LED Options 3 Dim Enable ee lt MENU gt lt ENTER gt
11. UP DOWN gt 2 Receive Links 3 Transmit Links A 4 lt UP DOWN gt 3 Transmit Links 4 Options 1 lt UP DOWN gt 4 Options 5 Advanced Edit Device is used to change the settings on a previously added device For instance the dimming can be disabled under the Options sub menu Model UPP Edit Device Sub Menu ID Pocket Programmer DID 2 yReceive Links lt UP DOWRK y DID J 2 Receive Links Y lt UP DOWK Y 2 yReceive Links 3 Transmit Links lt UP DOWhK v 3yTransmit Links 4 Options y v lt UP DOWhK y 4 Options 5 Advanced y v lt MENU gt 1 Add Device 2 Edit Device Model UPP lt Reading Device gt 1 Network Name lt ENTER gt 1 Network Name lt ENTER gt lt Writing gt New Network Name New Network Name lt UP DOWK gt lt LEFT RIGHT gt Select Character Select Position lt ENTER gt 2JRoom Name lt ENTER gt New Room Name lt UP DOWK gt lt LEFT RIGHT gt lt DOWN gt 2Room Name New Room Name lt Writing gt lt UP DOVWN gt Select Character Select Position lt ENTER gt lt Writing gt 3 Device Name lt ENTER gt 3 Device Name New UMA New UMA lt UP DOWK gt lt LEFT RIGHT gt lt UP DOWK gt Select Character Select Position 4 Network ID 4 Network ID lt Writing gt 001 lt ENTER 001 lt ENTER gt lt UP DOWN gt lt LEFT RIGHT gt Select Character
12. e Link 001 device was put in Setup Mode hence no Link deleted 4 Delete Device 5 Add Link v lt MENU gt or lt ENTER gt 5 Add Link 6 Delete Link lt UP DOWN gt devices as long as all are in Setup Mode Model UPP 16 Pocket Programmer UPB Explorer Smart Transmit 1 Access Network 2 New Network 1 Smart Transmit ENTER Select Type LINK Center Select Type Link lt ENTER gt lt UP DOWN gt A 2 Smart Receive Select NetID 001 7 ir UPON Ed SENIER 1 Access Networ 2 New Network 1 Smart Transmit Select Type DIRCT Link 001 lt UP DOWN gt 2 Smart Receive 1 Activate T 2 N N k lt UP DOWN gt lt ENTER gt ew Networ 3 UPB Explorer lt MENU gt 2 Smart Receive 3 Expert Receive A lt U Ge lt UP DOWN gt 3 Expert Receive 4 Expert Transmit Link 001 2 Deactivate Link 001 9 Blink v Smart Transmit is used test communications of Links or control of devices lt UP DOWN gt lt UP DOWN gt Model UPP To select Network ID To select Link ID 1 Activate lt Sent gt Activate Deactivate 1 2 3 4 Goto OFF 5 Goto lt ENTER gt 050 6 Fade UP STOP 7 Fade DOWN STOP 8 Fade STOP 9 Goto lt ENTER gt allows selection of level with lt UP DOWN gt buttons Fade UP STOP and Fade DOWN STOP brighten or dim while holding the lt ENTER gt but
13. gt y lt UP DOWN gt lt ENTER gt y 2 Xmit Atmpts Link Direct 3 Transmit Links 4 Options aD i X 1 Xmit Type TX Attempts 2 ST ie ME 2Xmit REA lt ENTER gt lt UP DOWN gt 1to 4 lt ENTER gt 4 Options 5 Advanced J iek 7 l lt gt 7 lt MENU gt 2 Xmit Atmpts lt ENTER gt Xmit to Repeatr lt UP DOWN gt Xmit to Repeatr ENTER gt lt Writing gt 3 Xmit 2 Rpeatr No Repeater Repeater Tx 1 i UP DOWN gt 1 Add Device 2 Edit Device Tx 1 to 3 13 Pocket Programmer 1 Add Device View Device 2 Edit Device View is Read Only ee lt MENU gt 1 Add Device View Device is used to check the 2 Edit Device l current settings of a UPB device Settings can be observed but not changed lt ENTER gt lt MENU gt 2 Edit Device 3 View Device nae aks lt MENU gt up Select DevID 002 wipe desired Device ID ELSE Err S Device Not Found If device is not found Select DevID 001 Select DevID 001 lt SAI UML gt lt ENTER gt y lt MENU gt 1 ID 2 Receive Links Go to Edit View lt ENTER gt Device Sub Menu lt UP DOWN gt 1 ID 2 Receive Links lt UP ee 2 Receive Links 3 Transmit Links A lt UP ee 3 Transmit Links 4 Options y e 4 Options 5 Advanced Model UPP 1 Access Network Delete Device 2 New Network J ER
14. he UPP MENU NAVIGATION Pressing the lt MENU gt button backs out of a selection without making changes Pressing lt ENTER gt opens the menu selection and sub menus Some menus require the use of the lt UP gt lt DOWN gt and lt RIGHT gt lt LEFT gt buttons to edit characters and move the cursor position Model UPP USING THE POCKET PROGRAMMER The pocket programmer mirrors the functionality of UPStart Configuration software If the installer is familiar with UPStart then most of the UPP menus and functions are intuitive and easy to use If there are any questions or difficulties in using the UPP referencing the specific function in the UPStart software is highly recommended The pocket programmer identifies device by Device ID number device names are not used It is highly recommended that the User knows has created a list or plan for the device s ID when programming A device s ID can Viewed by putting the device in setup mode then use the pocket programmer to View the device from the Access Network sub menu UPDATING THE POCKET PROGRAMMER The Pocket Programmer was designed with the future in mind As new UPB devices become available the UPP will need to have its program updated to allow use with these new devices To update your UPP please visit www Simply Automated com U PP UPDATE and follow the instructions A personal computer with a connection for a DB9 serial cable is required Pocket Programmer
15. le Model UPP IMPORTANT SAFETY INSTRUCTIONS When using electrical products basic safety precautions should always be followed including the following 1 READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2 Keep away from water If product comes into contact with water or other liquid unplug immediately 3 Never use products that have been dropped or damaged 4 Do not use this product outdoors 5 Do not use this product for other than its intended use 6 Toavoid risk of fire burns personal injury and electric shock install this product out of reach of small children 7 Do not cover the product with cloth paper or any material when in use 8 This product uses polarized plugs and sockets one blade is wider than the other as a feature to reduce the risk of electric shock These plugs and sockets fit only one way If they do not fit contact a qualified technician Do not use with an extension cord unless plugs can be fully inserted Do not alter or replace plugs 9 SAVE THESE INSTRUCTIONS Pocket Programmer INSTALLATION The Pocket Programmer is designed for indoor use Simply plug the appropriate end of the provided AC cord into the top of the UPP the other end into any 120 volt outlet anywhere in the house Once the Pocket Programmer completes its start up procedure the top two of six selections of the main menu are on the display and it is ready for use Kar ms y eg gt Vili mg mme meg vm TG T Ree uke
16. lt MENU gt v Select Net ID 001 Select Net ID 002 To desirec da SUP Network ID lt ENTER gt Y lt MENU gt Select Net ID 001 Select Pswd 0000 5 7 Continue until lt UP gt Select Net EN lt RIGHT gt Select Net DE desired Select Pswd 1000 Select Pswd 1000 Password Select DevID 001 lt UP DOWN gt To ka Device D lt ENTER gt 1 Add Device 2 Edit Device lt DOWh gt y DAdd Device 2 Edit Device 7 lt ENTER gt TENTER ork gt A Select DevID 001 lt Finding Device gt 2 Edit Device 3 View Device lt Set gt Delete y DOWN ck i MENU Net 001 Dev 001 3 View Device 4 Delete Device lt ENTER gt y Deleting Device lt Device Deleted gt Net 001 Dev 001 lt MENU gt or lt ENTER gt 14 Pocket Programmer 1 Access Network 2 New Network lt lt y lt ENTER gt lt MENU gt v Add Link Select Net ID 001 Select Net ID 002 gt lt UP gt lt ENTER gt y lt MENU gt lt UP gt Select Net ID 001 Select Pswd 1000 Select Net ID 001 UP Select Pswd 0000 ee lt ENTER gt lt Add Link is used to create and add a Link to one or more UPB devices To desired Network ID Continue until lt RIGHT gt Select Net ID 001 desired Select Pswd 1000 Password 1 Add Device 2 Edit Device y lt DOWN gt 1 Add Device 2 Edit Device
17. ton and stop upon release 17 Pocket Programmer Model UPP UPB Explorer Smart Receive Expert 1 Access Network Receive and Expert Transmit 2 New Network lt ENTER gt 1 Smart Transmit 2 Smart Receive lt UP DOWN gt lt UP DOWN gt 1 Access Network UPB While in this mode 2 New Network 1 Smart Transmit enter gt lt Monitoring UPB gt message Net 001 Link 001 the display will lt UP DOWN gt 2 Smart Receive dr ACTIVATE change with each lt UP DOWN gt lt MENU gt or lt ENTER gt UPB message 2 New Network UPB SJUPB Explorer 2 Smart Receive lt ENTER gt Monitoring UPB gt C1C2NtLkScMdLvRt message 3 Expert Receive j 890501010521FFFF received lt UP DOWN gt lt MENU gt or lt ENTER gt C1iC2NtLkScMdLvRt 890501010521 FF FF lt ENTER gt C1C2NtLkScMdLvRt lt UPB Transmited gt lt ENTER gt 3 Expert Receive 4 Expert Transmit Smart Receive is used to observe UPB transmissions lt MENU gt or lt ENTER gt lt UP DOWN gt To select Character lt LEFT RIGHT gt To select Position 18 Pocket Programmer 1 Access Network 2 New Network lt UP DOWN gt 1 Access Network 2 New Network lt UP DOWN gt 2 New Network 3 UPB Explorer lt UP DOWN gt 3JUPB Explorer 4 UPB Noise View lt UP DOWN gt 4 UPB Noise View 5 Run CIM lt UP DOWN gt 5 Run CIM 6 Set Contrast lt ENTER gt lt ENTER gt lt ENTER
Download Pdf Manuals
Related Search