Miele T382C - Operating instructions
Contents
1. Capacity Final spin speed Electricity Drying time incl in a domestic consumption cooling down washing machine time kg rem kWh mins Cottons Extra dry 5 1200 3 44 87 1400 3 28 83 1550 3 17 81 Normal 5 1200 3 17 81 1400 3 02 77 1550 2 91 75 Normal 5 1200 2 88 74 1400 2 74 71 1550 2 64 69 Hand iron AA 5 1200 2 10 56 1400 1 96 53 1550 1 86 51 Machine iron 5 1200 1 65 47 1400 1 51 43 1550 1 41 41 Minimum iron Normal 2 5 1000 1 68 50 Normal 2 5 1000 1 41 45 Hand iron 2 5 1000 1 21 37 All consumption data have been obtained through standard tests EN 61121 A11 Different types of fabric the load and residual moisture after spinning may affect the figures given 12 Emptying the condensed water container During the programme water is con m When the container is empty release densed and collected in a container on the cap The spout closes automati the left behind the fascia panel The cally container holds approx 4 litres and should be emptied after each drying programme m Push in the container until it clicks into place Should the container be inadvertently full when the tumble dryer is started or if it becomes full during operation m The Empty out container indicator light comes on Note The water collected in the container has been distilled by evaporation and can be used in a steam iron or humidi fier for example The foll2. On Off button is depressed m the door is properly closed m the mains plug is plugged in and the fuse or circuit breaker has not tripped Laundry is not sufficiently dry The load consists of dissimilar items in terms of size and fabric m Select a longer drying programme next time Small loads or individual items may cause the programme to terminate pre maturely m Small loads should therefore be time dried Problem solving guide Drying times are too long m Clean the fluff filter in the door The laundry was not spun for a suffi ciently long time The grille under the drum door is blocked preventing any intake of cool air Ventilation is inadequate e g in a small room m When the machine is in operation open a door or the window After cleaning the heat exchanger water leaks from the machine Check that the heat exchanger flap has ben replaced correctly If necess ary remove and replace Items made of synthetic fibres are charged with static electricity after drying Static charge can be reduced by ad ding fabric conditioner during the final rinse cycle in the washing machine or a fabric conditioner sheet in the tumble dryer Formation of fluff Fluff is principally the result of friction when items are worn and washed Ma chine drying hardly causes any fluff to form and as has been established by research institutes has no effect on the lifetime of fabrics Probl
3. Dept should be contacted Problem solving guide The interior drum lighting fails to function The bulb may be defective Replace it as follows m Switch off the machine or disconnect from the mains supply m Open the door m Use a 19 mm spanner to unscrew the plastic cover inside the drum above the door The light bulb must not exceed the maximum wattage quoted on the data plate and the plastic light cover m Replace the bulb and the plastic cover The cover must be fixed securely as otherwise moisture may seep in and cause a short circuit The temperature resistant bulb should only be ordered from your Miele Dealer or the Service Dept After sales service Inthe event of any faults which cannot be remedied or if the appliance is under guarantee please contact your Miele Dealer or the nearest Miele Service Depart ment see back cover for the ad dress When contacting the Service Depart ment please quote the Model and Ser ial nos of your appliance both of which are shown on the data plate on the right hand side below the opening to the drum Example Wy 6 aD germany Typ Installation The machine must be perfectly level to ensure safe and proper operation Minor differences do not however have an adverse effect on operation m The screw feet can be adjusted to compensate for any uneveness in the floor surface 20 Important The grille below th
4. cancel a programme m Turn the programme selector switch to Finish Programmes Cottons Empty out container O On O Drying or i 1 N j Do MADE IN GERMANY SEQUENCE Cooling down 8 Anti crease DRYING STAGE REACHED Machine Hand iron o iron NormalO PROGRAMME MINIMUM IRON Finish COTTONS Extra dry Normal Normal J Hand iron Hand iron b E t Machine iron 20 mins warm 15 mins cool air TIMED DRYING Extra dry Multi layer fabrics which would not be thoroughly dried using the Normal programme max 5 kg Note Jerseywear tends to shrink depending on the quality and type of manufactur ing involved The Extra dry pro gramme should therefore not be se lected for these fabrics Normal Mixed load of cotton fabrics e g towell ing and jerseywear i e single layer and multi layer fabrics max 5 kg Normal Homogeneous loads of cotton fabrics jerseywear flannelette sheets towel ling max 5 kg Note Should certain items still be slightly damp select the Normal pro gramme 10 Hand iron 44 Cotton or linen fabrics e g table linen bedding starched laundry etc max 5 kg Note Iffabrics are too damp for hand iron ing please select the Hand iron A pro gramme Machine iron Cotton or linen fabrics including star ched laundry for machine ironing max 5
5. for these types of garment In extreme cases do not tumble dry these garments Dark coloured garments should be dried separately from light coloured garments Loading the machine Load the laundry very loosely into the drum Duvet covers and pillowcases should be fastened before drying in order to prevent small items from being rolled in side them Important Please check that items of laundry cannot be trapped by the door as this will cause damage to the fabric Unloading the machine At the end of the programme remove the washing from the machine If this is not done the machine automatically proceeds into an intermittent anti crease action for 60 minutes This en tails the drum being rotated at short in tervals in order to reduce the possibility of the formation of creases Once the laundry has been removed check that the drum is empty Any items left in the drum could be dam aged through overdrying in the next programme Clean the fluff filter after each drying cycle to prevent excessive energy con sumption and longer programme run ning times The door should always be closed after use Programme selection Selecting a programme This tumble dryer is fitted with an elec tronic sensor system The required de gree of dryness is measured and moni tored electronically so that the heating element is switch
6. kg Note The laundry should be rolled up to pre vent it from drying out until it can be ironed Programmes Minimum iron and timed drying Empty out container O On I ON Low Door 0 OFF temp Buzzer Start J MADE IN GERMANY DRYING STAGE REACHED gt Machine land E o iron Sala PROGRAMME MINIMUM IRON Finish COTTONS Extra dry A Normal hi Normal jj Hand iron Hand iron 86 U Machine iron SEQUENCE O Drying O Cooling down O Anti crease Finish 20 mins warm 15 mins cool air TIMED DRYING Normal Minimum iron items made of synthetics or blended fabrics e g pullovers dresses trousers etc which are not dried adequately in the Normal pro gramme max 2 5 kg Normal Minimum iron shirts table cloths etc made of blended woven or knitted fab rics e g cotton synthetics max 2 5 kg Hand iron Minimum iron shirts table cloths etc made of blended woven or knitted fab rics e g cotton synthetics which are still to be hand ironed max 2 5 kg Note for all three programmes With blended fabrics consisting of wool and synthetics consult the manufac turer s instructions as the wool compo nent may become matted 15 minutes cool air Items which are only to be aired max 5 kg 20 minutes warm air Individual items e g bathing towels bathing trunks Programmes Consumption data
7. Miele NOVOTRO NIC Operating instructions for condenser tumble dryer T 440 C It is essential to read these opera ting instructions before installing or using the machine to avoid the risk of accident or damage to the machine T Nr 4580690 Contents Page Guide to the appliance oooocoocoococc een ren nenn 3 For the user Warning and safety instructions 0 0 nennen 5 Notes OomlaundIy Cit a ne ra ee A et 7 Loading and unloading WashiNQ o oooccoccco nennen 8 Programme selection a ras nds 9 Programmes TORCQOH NS 245 cca ee oo a nat mag leks eau dees 10 Programmes for Minimum iron and timed drying 222222 11 Programmes Consumption data 0 00 0 20 12 Emptying the condensed water container 2 0 0 0 0 13 Cleaning and Care ce sn aig rn Ae ea we We ee RGA A 14 Problem solving guide 0 0 0 2 cee 17 Alter sales SOI Suicide chou oe ade s de iad d 19 For the installer electrician Installation 2 4 da ra en zen de abate tats a a ate ua 20 Electrical CONMECON sc sae atl ne ea ek ats Rol ee ate ale ge Bh 21 Condensed Water Otitis sa Wr nenne 22 TEechniealData 244 urn aus te A Ped Po Ma TR aea Page SG Bes Rage le 2 24 Help to protect our environment Disposal of the packing material The packaging used to protect the machine during transport largely consists of the following recyclable materials Corrugated paper card Polystyrene CFC free Polyethylene foil transpar
8. and an appropriate plug fitted The plug cut from the flexible cord should be disposed of and on no account be in serted into a 13 A socket elsewhere in the house electric shock hazard The fuse cover must be refitted when changing the fuse and if the fuse cover is lost the plug must not be used until a suitable replace ment is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words in the base of the plug as applicable to the design of plug fitted The correct fuse rating of the replacement fuses that are ASTA ap proved to BS 1362 should be fitted Re placement fuse covers may be purchased from your local electrical suppliers elec tricity showroom or Miele Service Agent 21 External drainage of condensed water The condensed water can be drained m Push the drain hose onto the drain off directly if the machine is installed outlet Make sure that the hose is near a sink drain outlet etc firmly secured by the clip and not kinked Accessories supplied 2 m drain hose Hose clamp Rubber connection sleeve Hose clip Installation Max drain hose length 3 0 m Max delivery head 1 0 m m Detach the hose clip from the drain outlet at the back of the machine and remove the rubber plug 22 External drainage of condensed water The machine is fitted with a non return valve as standard to prev
9. can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with local and national regulations It is most import ant that this basic safety requirement is regularly tested by a qualified electri cian The manufacturer can not be held responsible for the consequences of an inadequate earthing system The machine is built in accordance with current safety requirements Unauthorised repairs could result in un foreseen dangers for the user for which the manufacturer can not accept responsibility Repairs should only be undertaken by a Miele approved engin eer In the event of a fault or for clean ing purposes the machine is only completely isolated from the electricity supply either when the plug is withdrawn or itis switched off at the mains the mains fuse is withdrawn Use There is a danger of fire with fab rics which contain rubber foam rubber or rub ber like materials have been treated with inflammable cleaning agents have been splashed with hair lac quer hair spray nail varnish remover or similar Always close the door after use This way you will avoid the danger of anyone sitting or leaning on the door which can cause the machine to tip up Do not install the machine in a room where the temperature may drop below freezing At very cold tempera tures the machine may be difficult to start At very cold tempe
10. ccordance with national and local safety regulations Connection should be made via a fused plug and a suitable switched socket which is easily accessible For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA The voltage rated load and fuse rating are given on the data plate Please en sure that these match the household mains supply Important The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live As the colours of the wires in the mains lead of this appliance may not corre spond with the coloured markings ident ifying the terminals in your plug pro Electrical connection ceed as follows The wire which is coloured green and yellow must be connected to the termi nal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red WARNING THIS APPLIANCE MUST BE EARTHED Non rewireable plugs BS 1363 U K If this machine or appliance is fitted with a non rewireable plug the follow ing information applies If the socket outlets are not suitable for the plug supplied with this product it must be cut off
11. e appliance must be properly installed and connected to the electricity supply Warning and safety instructions Please read the operating instruc tions before using the tumble dryer for the first time They contain im portant information about the safety use and maintenance of the ma chine This will avoid the risk of acci dents and damage to the machine Keep these operating instructions in a safe place and ensure that new users are familiar with the content Pass them on any future owner of the machine Correct usage The tumble dryer is only intended for drying fabrics which have been washed in a water solution marked on the manufacturer s wash care label as being suitable for tumble drying Any other applications may be dangerous The manufacturer is not liable for damage resulting from im proper use or operation Do not let small children play with the machine and its controls or operate it Please supervise its use by the elderly or infirm Technical safety Before connecting the machine en sure that the connection data on the data plate fusing voltage and fre quency matches the mains electricity supply If in any doubt consult a quali fied electrician Faulty components must only be exchanged for Miele original spare parts Only when these parts are fitted can the safety standards of the ma chine be guaranteed Warning and safety instructions The electrical safety of this ma chine
12. e drum door should never be blocked as this will prevent a sufficient intake of cold air Installation It is possible to install this appliance under a continuous worktop in a row of kitchen units using a special conver sion kit The machine lid is replaced by a coverplate which must be fitted by a suitably competent person to ensure electrical safety When installing under a worktop with a working height of 900 910 mm a spacer kit is needed When built under the programme run ning times may be longer The tumble dryer can also be com bined with a Miele washing machine in a washer dryer stack For this purpose the appropriate stacking kit to match your washing machine is required These items are all available from your Miele Dealer For U K only This tumble dryer is supplied ready for connection to an a c single phase 230 V 50 Hz supply The rated load is 3 kW The machine is supplied with a2 m long mains cable with moulded plug and the fuse rating is 13 A The appliance should be connected up only by a qualified elec trician in accordance with national and local safety regulations For other countries This tumble dryer is supplied ready for connection to an a c single phase 220V 60 Hz supply The rated load is 2 86 kW The machine is supplied with a 2 m long mains cable with moulded plug and the fuse rating is 16 A The appliance should be connected up only by a qualified elec trician in a
13. ed off as soon as it is reached The drying cycle automati Cally finishes with a cooling down period This may be followed by the anti crease action cycle The following drying programmes are available Cottons six drying levels from Extra dry to Machine iron Minimum iron three drying levels from Normal to Hand iron Timed drying 15 mins cool air and 20 mins warm air Low temperature By selecting Low temperature the temperature can be lowered for deli cate fabrics e g acrylic Correct procedure m Load the drum m Close the door m Switch on the machine m Select a programme by turning the selector switch clockwise or anti clockwise Select Low temperature if required m Press Start After drying m Turn the programme selector switch to Finish m Switch the machine off m Clean the fluff filter Opening the door during a pro gramme If the door is opened during a pro gramme the programme will have to be started again m Close the door m Press Start The selected programme restarts The programme is not continued if There is a power failure lasting more than 30 minutes The programme has already reached the Cooling down or Anti crease stage To reselect a different programme during drying m Set the programme selector switch to the required programme The new programme starts from the be ginning To
14. em solving guide To open the door in the event of power failure m Using the spatula provided lever the door open Water droplets appear at the upper edge of the drum aperture A double filter system with double seal prevents fluff from being deposited in the heat exchanger This means that the heat exchanger does not need to be cleaned so often The double seal may lead to the build up of condensate Laundry being removed from the machine may come into contact with these water droplets They will however dry off in a matter of minutes 18 The Anti crease indicator lamp in the sequence indicator display starts flashing m Release the On Off button and then press it in again m Press the Start button If the indicator lamp starts flashing again this indicates a fault in the ma chine Please then contact your Miele Dealer or the Miele Service Dept The drum door opens during the drying cycle The machine has overheated The tem perature limiter opens the drum door and thus causes the machine to switch off automatically Possible reasons for overheating m The fluff filters in the door and in the door opening are clogged m The heat exchanger is blocked Before restarting the programme pro ceed as follows m Clean the affected part of the ma chine m Press the Start button Should the drum door open again this must be due to a technical fault and the Service
15. ent Fibreboard solvent free Untreated wood Packaging straps Polyamide blue Polypropylene black Rather than just throwing these materials away please take them to the nearest col lection point for specific waste Disposal of your old appliance Old appliances contain materials which can be recycled Please contact your local authorities or scrap merchant about potential recycling schemes before dis posing of the appliance Guide to the appliance 1 a c connection cable 2 m long with plug for connection to 240 V 50 Hz 13 A GB 2 Condensed water container 3 Drum door 4 Control panel 5 Drain hose for condensed water 6 Four height adjustable screw feet Guide to the appliance Empty out container O On i 1 N j MADE IN GERMANY DRYING STAGE REACHED Machine Hand iron o iron O NormalO PROGRAMME MINIMUM IRON Finish COTTONS Extra dry D Normal Hand iron b U Machine iron SEQUENCE O Drying O Cooling down 8 Anti crease Normal Hand iron 20 mins warm 15 mins cool air TIMED DRYING J Pushbuttons Door opens the door On Off for switching the appliance on and off Low temperature low temperatures for delicate fabrics e g acrylics Buzzer sounds when the drum turns during the intermittent anti crease action period Start starts a drying programme Indicator light Empty out containe
16. ent water from flowing back into the machine eg if the machine is connected to a siphon m Close the water inlet port above the condensed water container with the bottom part of the rubber plug The plug must face towards the interior of the machine so that the con densed water container can easily be inserted Connection to wash basin drain outlet Push the hose clip 1 and knurled nut connector 2 from the sink drain outlet over the drain hose Put the adapter sleeve 3 supplied into the hose Screw the drain hose to the drain out let with the knurled nut connector m Tighten the hose clip 1 up close to the nut 2 23 Technical data Max delivery head Max d rain hose length Test certificates awarded Electrically suppressed 24 85 0 cm adjustable 1 0 5 cm 59 5 cm 60 0 cm 55 kg 103 5 kg dry weight See data plate 1 0m 3 0m Radio TV suppression VDE Acc to DIN EN 60555 VDE 0838 25 26 27 Miele United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW tel Abingdon 01235 554455 telex 837 121 fax 01235 554477 Service Office tel Abingdon 01235 554466 Alteration rights reserved 000 GB 5095
17. ng pads to clean the machine Cleaning and care Heat exchanger The heat exchanger should be cleaned once or twice a year Before cleaning disconnect the ma chine from the mains supply m Open the door m Turn both levers on the heat ex changer so that they are vertical m Turn the flap lever so that it is vertical Cleaning and care A m Clean the heat exchanger 16 at both ends front and back and along the two long sides m Stand the heat exchanger lengthwise on a towel until it is quite dry m Replace the heat exchanger in the reverse order Attempt to pull forward the heat ex changer and the flap to check that both are firmly positioned as otherwise water may leak from the machine Electrical appliances should only be repaired by qualified personnel In correctly repaired machines may pose a considerable risk to the user There are however minor faults which can be corrected without contacting the Service Department The tumble dryer fails to start when switched on Check whether the On indicator lamp lights up If so failure to start may be due to an incorrect selection procedure sequence when switching on the ma chine m Repeat the switch on procedure in the correct sequence see P 9 Ifthe On indicator lamp does not light up check that m the
18. owing points should be remem bered The laundry should be thoroughly rinsed before it is loaded in the tumble dryer As a precautionary measure the water should be passed through a fine sieve or coffee filter in order to strain out any very small particles of fluff from the water which might otherwise cause damage m Pull forward the cap of the spout as indicated by the arrow and hold open while emptying the container Cleaning and care The fluff which occurs during drying is collected in the fluff filter in the door Clean the filter after every programme to save time and energy m Grip the filter by the recessed handle and pull upwards to clean m Remove any remaining fluff from the hollow part of the door through the wide slit at the bottom 14 Remove fluff from the filters in the door opening These filters can be taken out and rinsed if necessary Dry the filters before putting them back in place Before cleaning the tumble dryer Al ways disconnect the machine from the power supply The dryer can be cleaned with a cloth using soapy water or a mild detergent not scouring powder and dried with a soft cloth The drum may be cleaned using a suitable proprietary stainless steel cleaner following the manufactu rer s instructions The machine must never be hosed down Do not use any abrasive sub stances or scouri
19. r Programme sequence indicator lights On Drying Cooling down Anti crease Finish Programme selector switch Cottons Extra dry Normal Normal Hand iron Hand iron 44 Machine iron Minimum iron Normal Normal Hand iron Timed drying 15 mins cool air 20 mins warm air Drying stage display This shows the stage of drying reached For programmes Normal and Extra dry the indicator light re mains at the Normal position Guide to the appliance Environmentally conscious drying The sensitive system automatically ad justs drying to suit the water quality The water conductivity is measured and registered by the control which then compensates to achieve a uniform residual moisture level The Novotronic control offers 9 programmes with elec tronic moisture measuring and 2 timed programmes The automatic reversing action turns the drum clockwise and anti clockwise to loosen the laundry and prevent damp patches and thus to ensure even drying results Energy saving tips Make sure that your laundry is thor oughly spun before drying You will save up to 35 energy and time if laundry is spun at full spin speed in stead of at 600 rpm Load according to the optimum amount of washing for the programme to be selected Underload ing is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Before using for the first time Important Th
20. ratures the ma chine may be difficult to start Laundry will not dry and the anti crease indica tor light will flash to indicate there is a problem Freezing condensed water in the pump hoses and in the condensed water container can lead to damage Make sure the drain hose is se curely attached if you hang it ina sink or basin external drainage of con densed water to avoid the hose slip ping and the water causing damage Condensed water is not drinking water It can cause health prob lems in people and animals Using accessories Accessory parts may only be fitted when expressly approved by Miele If other parts are used guaran tee performance and product liability claims may be invalidated Disposal of your old machine Before discarding an old machine unplug it Render the plug useless Cut off the cable directly behind the ap pliance to prevent misuse Notes on laundry care Before drying check the drying symbol on the textile care label Significance of symbols Dry at normal temperature Dry at low temperature El Do not tumble dry If no symbol is featured dry at your own risk applying the following principles Cottons and minimum iron items should be dried at a normal tempera ture at the appropriate programme setting For delicate fabrics e g acrylic fibres the low temperature setting should be selected The following fabrics should not be dried in a tumble dr
21. yer Woollens and wool blends These fabrics tend to become matted and shrink Items filled with down The fine fabric interior tends to shrink depending on the quality involved Pure linen These items should only be machine dried if specified as suitable by the manufacturer on the textile care label as the surface of the fabric may other wise tend to roughen Note Some woven and loopknit materials tend to shrink to varying extents de pending on their quality This tendency is exaggerated by over drying When purchasing woven materials it is advisable to take their shrinkage properties into account Starched washing can also be dried in the tumble dryer In order to achieve the usual finish double the amount of starch should be used Select the most suitable programme for hand or machine ironing Minimum iron items should be spun for 10 to 30 seconds before being tumble dried Such fabrics tend to crease if overdried These items should be given only a short period in the dryer and taken out slightly damp The Minimum iron Normal programme is recom mended Minimum iron shirts in 100 cotton may crease during tumble drying de pending on the quality and weave Minimum iron fabrics tend to crease more the greater the load This is par ticularly true of very delicate fabrics The load should be reduced to 1 5 kg or if necessary to 1 kg The Hand iron setting is recommended
Download Pdf Manuals
Related Search