RedMax CHT2300L Specifications
Contents
1. ii 15 PRE 17 A Safety Precautions MIN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR HEDGE TRIMMER eRead this Owner Operator Manual carefully Be sure you understand how to operate this unit properly before you use it Failure to do so could result in serious injury Be sure to keep this manual handy so that you may refer to it later whenever any questions arise Also note that you are requested to contact the dealer from whom you purchased the product for assistance in the event that you have any questions which cannot be answered herein e Always be sure to include this manual when selling lending or otherwise transferring the ownership of this product e This product has been designed for use in trimming leaves and branches from trees and hedges and it should never be used for any other purpose since doing so could result in unforeseen accidents and injuries occurring e This product is equipped with extremely sharp blades and when used improperly these blades can be extremely dangerous For this reason you should never use this hedge trimmer when under the influence of alcohol when suffering from exhaustion or lack of sleep when suffering from drowsiness as a result of having taken cold medicine or at any other time when a possibility exists that your Judgment might be impaired or that you might not be able to operate the hedge trimmer properly and in a safe manner Also be sure never2. compter de la date de livraison initiale d une unit Telles sont les limites de la garantie Le co t du transport de l unit jusqu au revendeur RedMax et depuis celui ci sera la charge de l acheteur L acheteur ne supportera pas le co t de main d oeuvre du diagnostic qui am ne la conclusion qu une pi ce garantie est d fectueuse si ce diagnostic est effectu chez le revendeur RedMax L acheteur ou propri taire a pour responsabilit d effectuer l entretien obligatoire tel que d fini par le fabricant dans le manuel du propri taire de l utilisateur Toute pi ce garantie dont le remplacement n est pas pr vu dans le cadre de l entretien obligatoire ou pour laquelle est seulement pr vue une inspection p riodique pour remplacement ou r paration si n cessaire sera garantie pour la p riode de garantie Toute pi ce garantie arriv e l ch ance de son premier remplacement pr vu sera garantie jusqu celui ci Toute pi ce de rechange quivalente en performance ou en durabilit peut tre utilis e pour l entretien hors garantie ou les r parations hors garantie et ce sans r duire l obligation de garantie incombant a la soci t La soci t sera tenue responsable des dommages aux autres composants du moteur caus s par la d faillance de pi ce s garantie s en p riode de garantie La garantie ne s applique pas aux unit s endommag es par suite de n gligence dans la mise en oeuvre des instructions sp cifi
3. Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage and remove any waste which has attached itself to the hedge trimmer Note that it is necessary to remove the plug guard shown in Figure 20 in order to be able to view the upper part of the cylinder IMPORTANT If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins it may cause the engine to overheat and that in turn may cause mechanical failure on the part of the hedge trimmer Cylinder fin Intake air cooling vent back Maintenance W PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1 Remove the muffler insert a screwdriver into the vent and wipe away any carbon buildup Wipe away any carbon buildup on the muffler exhaust vent at the same time Screwdriver 2 Tighten all screws bolts and fittings 3 Check to see if any oil or grease has worked its way in between the clutch lining and drum and if it has wipe it away using oil free lead free gasoline Storage e Old fuel left in the carburetor can cause starting failure Before storing the unit empty the fuel tank and drain the carburetor with the priming pump equipped on it Specifications M HT2300A HT2300L Type EE EE EE AAA Reciprocating single sided dual blades Blade size EDE nn EE EE nn nn EE nn KE EE EE EE EL 29 5 40 in 750 1 000 mm Dry weight EE E
4. es dans le manuel du propri taire de l utilisateur en vue d une utilisation et d un entretien correct fausse man uvre accidentelle modification utilisation abusive lubrification incorrecte utilisation de pi ces ou d accessoires autres que ceux sp cifi s par la soci t ou autres causes hors du contr le de la soci t Cette garantie ne couvre pas les pi ces remplac es en raison de leur usure normale ou de changements d apparence sans effets Il n existe aucune autre garantie explicite Les garanties implicites celles de n gociabilit du produit et de son adaptabilit un usage d fini incluses sont limit es deux 2 ans pour un usage priv un 1 an pour toute autre utilisation compter de la date initiale de livraison Les responsabilit s pour les dommage cons quents ou incidents sont exclues de toutes les garanties Certaines provinces n autorisant pas les limitations la dur e des garanties implicites ou les exclusions ou limitations relatives aux dommages incidents ou cons quents la limitation indiqu e ci dessus peut ne pas vous tre applicable Cette garantie vous donne des droits juridiques sp cifiques et vous pouvez galement jouir d autres droits variant d une province l autre Si vous d sirez obtenir des informations sur le centre de service le plus proche veuillez appeler KOMATSU ZENOAH AMERICA INC au 770 381 5147 Note importante vous recevrez une carte d enregistrement de garan
5. 11670 04064 02512 1111 91003 1030 91340 1110 91320 3540 91120 6836 91140 6839 91140 3884 11660 6845 13310 6845 13320 3880 95020 3880 95010 M sm A tet QQ A NON 1 NNN 1 aN a a a it mm BNNPDN AH NI HAH 9 I dodo doo M mm SI OT ON OT SK m NON NA mm r OOONNDON N I AH QG HK J do dodo o doo o Optional part Optional part Parts List Fig 4 ENGINE GROUP CHT2300B amp CHT2300L Parts List Fig 4 ENGINE GROUP CHT2300B amp CHT2300L 0 JO O1 BR D Cylinder Gasket base Bolt M5x22 Insulator Gasket insulator Gasket carb Screw M5x20 Muffler ass y e Muffler Spark arrester Bolt M5x50 Gasket muffler Plate muffler Screw M4x16 Crancase comp Gasket case Bearing Oil seal Oil seal Snap ring Bolt M5x30 Guard Screw M5x14 Piston Ring piston Pin piston Snap ring Bearing Washer Crankshaft comp Nut Key Shoe Screw Spring Washer Washer Case clutch Screw M5x16 Plate clutch Nut Rotor Coil ass y e Cord e Cap Cap spark plug Spring Grommet Spacer Bolt M4x25 Recoil ass y e Case recoil Spring Spiral e Reel Ratchet Spring e Screw e Retainer e Washer 5602 12110 5500 12213 1850 12130 9500 13163 9500 13121 9500 13131 0263 90520 9603 15100 9603 15110 1601 15120 01252 30550 9600 15210 9600 15220 0263 90416 9600 21100 9500 21141 06030 06001 2169 21210 1850 21220 040
6. counter clockwise IDLE SET SCREW NOTE Warm up the engine before adjusting the idling speed E HOW TO USE e This machine is designed so as to cut twigs upto 8 mm 0 3 inches thick Cutting too thick twigs or metal wires can not only break the blade teeth but also give damage to the drive mechanism When trimming leaves and thin twigs guide the blades as drawing a half circle on the surface and you will get a better finish e Running the engine at high speed with the blades Jammed up can shorten the life of clutch parts When the blades have been jammed by thick twigs stop operation at once and draw your unit off the objects after stopping the engine When clipping comparatively thick twigs move your unit slowly back and forth like a saw and they can be cut to fine finish NOTE When a new unit is first operated in the first few minutes grease may come out of the gear case But since this is excess grease there is no cause for alarm For next use just wipe it off with the engine stopped Maintenance e Make sure that the engine has stopped and is cool before performing any service to the hedge trimmer Contact with moving cutting head or hot muffler may result in a personal injury H DAILY INSPECTION Check all the fasteners for loose or missing ones e Brush off dirt on the blades and apply a light coating of oil NOTE e The blades are loose installed to the guide bar with several screws a
7. to allow children or anyone unable to fully understand the directions given in this manual to use this hedge trimmer e Avoid running the engine indoors The exhaust gases contain harmful carbon monoxide Never use your hedge trimmer under circumstances like those described below 1 When the ground is slippery or when other conditions exist which might make it not possible to maintain a steady posture while using the hedge trimmer 2 At night at times of heavy fog or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the area where the hedge trimmer is to be used to ensure safety 3 During rain storms during lightning storms at times of strong or gale force winds or at any other times when weather conditions might make it unsafe to use this product When using this product for the first time before beginning actual work take the hedge trimmer to a wide clear open space turn on the power and practice handling the hedge trimmer until you are sure that you will be able to handle in it properly in actual operation Lack of sleep tiredness or physical exhaustion results in lower attention spans and this in turn leads to accidents and injury When planning your work schedule allow plenty of time to perform the work of trimming and allow plenty of time for rest Limit the amount of time over which the hedge trimmer is to be used continuously to
8. unit Select outdoor bare ground for fueling and move at least 3m 10ft away from the fueling stop before starting the engine e The RedMax engines are lubricated by oil specially formulated for air cooled 2 cycle gasoline engine use If RedMax oil is not available Use an anti oxidant added quality oil expressly labeled for air cooled 2 cycle engine use RECOMMENDED MIXING RATIO GASOLINE 32 OIL 1 Exhaust emission are controlled by the fundamental engine parameters and components eq carburation ignition timing and port timing without addition of any major hardware or the introduction of an inert material during combustion 32 1 MIXING CHART 2CYCLE OIL thee 4 8 12 16 20 2GYGLE OIL mi 32 64 96 128 160 These engines are certified to operate on unleaded gasoline Make sure to use gasoline with a minimum octane number of 90 ROZ USA Canada pump octane min 87 eUnleaded gasoline is recommended to reduce the contamination of the air for the sake of your health and the environment e Poor quality gasolines or oils may damage sealing rings fuel lines or fuel tank of the engine E HOW TO MIX FUEL 1 Measure out the quantities of gasoline and oil to be mixed 2 Put some of the gasoline into a clean approved fuel container 3 Pour in all of the oil and agitate well 4 Pour in the rest of gasoline and agitate again for at least one minute 5 Put a clear indication on the outside of the contai
9. 65 02812 01252 30530 9500 22110 0263 90514 5600 41111 1100 41210 1101 41310 1260 41320 9500 41410 1101 41340 5600 42001 1650 43230 1000 43240 1140 51111 1140 51250 1600 51223 1140 51230 1970 51241 9600 52110 0263 90516 9600 52150 1650 43230 9601 71110 9600 71200 9600 71220 2616 71320 9500 72110 1900 72120 9500 72130 1260 71261 3310 72150 9990 75101 9990 75110 9990 75120 9990 75130 9990 75140 9990 75151 9990 75270 9990 75160 9990 75170 e Rope e Knob Screw Bracket Gasket carburetor Carburetor ass y Screw e Ring e Swivel e Valve ass y e O ring e Jet 37 e Rebuilt Kit e Body ass y e e e Screen e e Gasket Kit e e e Diaphragm pump e e Gasket pump e e e Diaphragm e e e Gasket diaphragm e Body purge e Pump priming e Cover pump e Screw Screw Label recoil Cap Screw M5x60 Clip Body ass y e Sleeve e Plate choke e Lever choke e Screw Element Cover ass y e Knob Cover fan Screw M5x20 Cover engine Screw M5x12 Screw Spark plug Grommet Cord comp Clamp Cable comp Clamp Tank ass y e Cap ass y e e Packing e e Holder e Filter e e Stopper Pipe comp Filter ass y e Clip Clip 1861 75180 1490 75181 0263 90412 5628 83221 5500 13131 5602 81001 9850 81110 1751 81130 1881 81140 1751 81240 9628 81250 5602 06030 1850 81450 9602 06020 1850 81490 1751 81510 1850 81520 1850 81530 9500 85510 9603 91120 1601 81810 0263
10. 6833 93112 103 Cr OWNER OPERATOR MANUAL HEDGE TRIMMERS HT2300A HT2300L CHT2300B CHT2300L HT2300A HT2300L CHT2300B CHT2300L WARNING Thank you for purchasing a RedMax product Before using our hedge trimmers please read this manual carefully to understand the proper use of your unit The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm APPLICABLE SERIAL NUMBERS HT2300A CUTTING UNIT 900532 and up ENGINE UNIT 968060 and up HT2300L CUTTING UNIT 900101 and up ENGINE UNIT 968060 and up CHT2300B CUTTING UNIT 901223 and up ENGINE UNIT 972833 and up CHT2300L CUTTING UNIT 900504 and up ENGINE UNIT 972833 and up Read this manual carefully to understand all safety precautions controls proper operation and maintenance of your RedMax hedge trimmers Failure to do so could result in serious injury SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury and for this reason you are requested to read all such instructions carefully and follow them without fail Note that there may be times when warning seals peel off or become soiled and impossible to read If this happens you should contact the dealer from which you purchased the product to order new seals and affix the
11. 90 75140 9990 75151 9990 75270 9990 75160 9990 75170 e Rope e Knob Screw Bracket Gasket carburetor Carburetor ass y Screw e Ring e Swivel e Valve ass y e O ring e Jet 37 e Rebuilt Kit e Body ass y eee Screen e e Gasket Kit e e e Diaphragm pump e e Gasket pump e e e Diaphragm e e e Gasket diaphragm e Body purge e Pump priming e Cover pump e Screw Screw Label recoil Cap Screw M5x60 Clip Body ass y e Sleeve e Plate choke e Lever choke e Screw Element Cover ass y e Knob Cover fan Screw M5x20 Cover engine Screw M5x12 Screw Spark plug Grommet Cord comp Tube Cable comp Tank ass y e Cap ass y e e Packing e e Holder e Filter e e Stopper Pipe comp Filter ass y e Clip Clip 1861 75180 1490 75181 0263 90412 5628 83221 5500 13131 5602 81001 9850 81110 1751 81130 1881 81140 1751 81240 9628 81250 5602 06030 1850 81450 9602 06020 1850 81490 1751 81510 1850 81520 1850 81530 9500 85510 9602 91120 1601 81810 0263 90560 1950 86120 9500 82102 1970 82190 9500 82131 9500 82140 2630 33610 9500 82171 9600 82203 9500 82221 9600 31110 0263 90520 9600 32101 1850 32160 1900 31410 5602 73110 1852 72121 5602 73200 5602 73310 1751 82101 9607 85001 9607 85201 9500 85220 9601 85300 9601 85260 4820 85260 5500 85300 9500 85400 1260 85460 1950 86120 gt ee Parts List Fig 3 CUTTER GROUP CHT2300B a
12. 90560 1950 86120 9500 82102 1970 82190 9500 82131 9500 82140 2630 33610 9500 82171 9600 82203 9500 82221 9600 31110 0263 90520 9600 32101 1850 32160 1900 31410 5602 73110 1852 72121 5601 73200 1140 72231 9601 83100 1140 72231 5607 85001 9607 85201 9500 85220 9601 85300 9601 85260 4820 85260 9500 85300 59500 85400 1260 85460 1950 86120 gt ee CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE IN CALIFORNIA NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED BUILT AND EQUIPPED TO MEET THE STATE S STRINGENT ANTI SMOG STANDARDS KOMATSU ZENOAH Co MUST WARRANT THE EMISSION CONTROL SYSTEM ON YOUR LAWN AND GARDEN EQUIPMENT ENGINE FOR THE PERIODS OF TIME LISTED BELOW PROVIDED THERE HAS BEEN NO ABUSE NEGLECT OR IMPROPER MAINTENANCE OF YOUR LAWN AND GARDEN EQUIPMENT ENGINE YOUR EMISSION CONTROL SYSTEM MAY INCLUDE PARTS SUCH AS THE CARBURETOR THE IGNITION SYSTEM AND CATALYTIC CONVERTER ALSO INCLUDED MAY BE THE HOSES BELTS CONNECTORS AND OTHER EMISSION RELATED ASSEMBLIES WHERE A WARRANTABLE CONDITION EXISTS KOMATSU ZENOAH Co WILL REPAIR YOUR LAWN AND GARDEN EQUIPMENT ENGINE AT NO COST TO YOU INCLUDING DIAGNOSIS PARTS AND LABOR MANUFACTURER S WARRANTY COVERAGE THE 1995 AND LA
13. A HT2300L CHT2300B CHT2300L NOTE 1 Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and or replacement KOMATSU ZENOAH does not warrant the machines which have been damaged by the use of any parts other than those specified by the company When placing parts orders for repair and or replacement check if the model name and the serial number are applicable to those specified in the parts list then use parts number described in the parts list 4 The contents described in the parts list may change due to improvement 5 The parts for the machine shall be supplied seven 7 years after the machine is discontinued lt is possible that some specific parts may be subject to change of their delivery term and list price within the limit of ten 7 years after the machine is discontinued It is also possible that some parts may be available even after the limit of seven 7 years APPLICABLE SERIAL NUMBERS Mar 2001 HT2300A CUTTING UNIT 900532 and up ENGINE UNIT 968060 and up HT2300L CUTTING UNIT 900101 and up ENGINE UNIT 968060 and up CHT2300B CUTTING UNIT 901223 and up ENGINE UNIT 972833 and up CHT2300L CUTTING UNIT 900504 and up ENGINE UNIT 972833 and up Parts List Fig 1 CUTTER GROUP HT2300A amp HT2300L 18 Parts List Fig 1 CUTTER GROUP HT2300A 8 HT2300L Key Description Part Number 2300A 2300L Right handle comp Washer Reinforce Reinforce Guide plate Guide pl
14. DE EE EE ZITTI TIZI MII TTI I III nn II III III III III III III III EE ELIE 12 13 los 6 6 5 kg Engine Type annnunnanenunnnnnennunnnnnennnnunnnnnunnanennnnnnnnennnnnnnunnnnnnnnnnnnnnen Air cooled 2 stroke gasoline Model ona Zenoah G23LH Displacement EE EE EE OO EE OO EE KE EE EE EE EE 22 5 CC Fuel A Mixture Gasoline 32 Oil 1 Carburetor anununnnannunnunnnnennnnnnnnennnennnunnunnnnunnnnanennnnnnnnennnnnnnnnnnne Walbro Diaphragm type Spark plug O Champion RCJ6Y Fuel tank capacity ENKO EE EN EE NT EE EE ONE EE ET EE EE EI 20 fl oz 0 6 2 Transmission A Centrifugal clutch Cam crank Reduction ratio AS 4 14 m CHT2300B CHT2300L Type AAA Reciprocating duble sided dual blades Blade size A AA 23 6 30 in 600 760 mm Dry weig IS 1 0 8 1 1 3 lbs 5 4 5 6 kq Engine Type anununnunennnnnnnennnnnnnnennnnunnnnnnnnnennnnnnnnenunnnnnnnnnnnnnunnnnnnen Air cooled 2 stroke gasoline Model DR nn nn nn nn nn Na n n a n nn en nn nn INI Saa DE ES III III III III TITLE Zenoah G23LH Displacement AA 22 5 CC Fuel DR nn nn TITTLE LLL Mixture Gasoline 32 Oil 1 Carburetor anununnunnunnnnnnennnnnnnnennnnnnnnnnunnnnunnnnnnennnnnnnnennnnnnnnnnene Walbro Diaphragm type Spark plug O Champion RCJ6Y Fuel tank capacity KEK EE EE EE ON EE OO EE EE ONE EE EE EKI 20 fl oz 0 6 2 Transmission AS Centrifugal clutch Cam crank Reduction ratio nn nn nn EE TET 4 14 Specifications are subject to change without notice Parts List HEDGE TRIMMERS HI2300
15. INT FOR THAT PART ANY REPLAGEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DURABILITY MAY BE USED IN NON WARRANTY MAINTENANCE OR REPAIRS AND SHALL NOT REDUGE THE WARRANTY OBLIGATION OF THE COMPANY THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAILURE OF A WARRANTED PARTS STILL UNDER WARRANTY THIS WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF INSTRUCTION LISTED IN THE OWNER OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS AGCIDENT MISHANDLING ALTERATION ABUSE IMPROPER LUBRICATION USE OF ANY PARTS OR ACCESSORIES OTHER THAN THOSE SPECIFIED BY THE COMPANY OR OTHER CAUSES BEYOND THE COMPANY S CONTROL THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN THEIR APPEARANCE THERE ARE NO OTHER EXPRESS WARRANTIES IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO TWO 2 YEARS OF HOME USE ONE 1 YEAR FOR ANY OTHER USE FROM THE ORIGINAL DELIVERY DATE LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES ARE EXCLUDED SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IF YOU NEED TO OB
16. List Fig 2 ENGINE GROUP HT2300A amp HT2300L Parts List Fig 2 ENGINE GROUP HT2300A amp HT2300L 0 JO O1 BR D Cylinder Gasket base Bolt M5x22 Insulator Gasket insulator Gasket carb Screw M5x20 Muffler ass y e Muffler Spark arrester Bolt M5x50 Gasket muffler Plate muffler Screw M4x16 Crancase comp Gasket case Bearing Oil seal Oil seal Snap ring Bolt M5x30 Guard Screw M5x14 Piston Ring piston Pin piston Snap ring Bearing Washer Crankshaft comp Nut Key Shoe Screw Spring Washer Washer Case clutch Screw M5x16 Plate clutch Nut Rotor Coil ass y e Cord e Cap Cap spark plug Spring Grommet Spacer Bolt M4x25 Recoil ass y e Case recoil Spring Spiral e Reel Ratchet Spring e Screw e Retainer e Washer 5602 12110 5500 12213 1850 12130 9500 13163 9500 13121 9500 13131 0263 90520 9603 15100 9603 15110 1601 15120 01252 30550 9600 15210 9600 15220 0263 90416 9600 21100 9500 21141 06030 06001 2169 21210 1850 21220 04065 02812 01252 30530 9500 22110 0263 90514 5600 41111 1100 41210 1101 41310 1260 41320 9500 41410 1101 41340 5600 42001 1650 43230 1000 43240 1140 51111 1140 51250 1600 51223 1140 51230 1970 51241 9600 52110 0263 90516 9600 52150 1650 43230 9601 71110 9600 71200 9600 71220 2616 71320 9500 72110 1900 72120 9500 72130 1260 71261 3310 72150 9990 75101 9990 75110 9990 75120 9990 75130 99
17. TAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER PLEASE CALL KOMATSU ZENOAH AMERICA ING AT 770 381 5147 IMPORTANT YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE PLEASE FILL OUT THE CARD AND SEND IT TO RedMax KOMATSU ZENOAH AMERICA WITHIN SEVEN 7 DAYS BE SURE TO KEEP A COPY FOR YOUR RECORDS KOMATSU ZENOAH AMERICA INC 4344 Shackleford Road Suite 500 Norcross Georgia 30093 RedMax Garantie limit e 2 ans Pi ces en rapport avec les missions de gaz d chappement KOMATSU ZENOAH AMERICA ING par l interm diaire de n importe quel revendeur RedMax r parera gratuitement ou remplacera gratuitement pour l acheteur initial et chaque acheteur successif toute s pi ce s se r v lant de constitution et ou de montage d fectueux pendant deux 2 ans compter de la date initiale de livraison d une unit Les pi ces en rapport avec les missions de gaz d chappement sont l assemblage carburateur l assemblage bobine le rotor la bougie le filtre air le filtre carburant la tubulure d admission et les joints Toutes autres pi ces except es celles mentionn es ci dessus La soci t par l interm diaire de n importe quel revendeur RedMax r parera gratuitement ou remplacera gratuitement pour l acheteur initial toute s pi ce s se r v lant de constitution et ou de montage d fectueux pendant deux 2 ans en cas d utilisation priv e un 1 an pour toute autre utilisation
18. TER UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES ARE WARRANTED FOR TWO YEARS IF ANY EMISSION RELATED PART ON YOUR ENGINE IS DEFECTIVE THE PART WILL BE REPAIRED OR REPLACED BY KOMATSU ZENOAH Co OWNER S WARRANTY RESPONSIBILITIES AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER YOU ARE RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE LISTED IN YOUR OWNER S MANUAL KOMATSU ZENOAH Co RECOMMENDS THAT YOU RETAIN ALL RECEIPTS COVERING MAINTENANCE ON YOUR LAWN AND GARDEN ENGINE BUT KOMATSU ZENOAH Co CAN NOT DENY WARRANTY SOLELY FOR THE LACK OF RECEIPTS OR FOR YOUR FAILURE TO ENSURE THE PERFORMANCE OF ALL SCHEDULED MAINTENANCE AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER YOU SHOULD BE AWARE HOWEVER THAT KOMATSU ZENOAH Co MAY DENY YOU WARRANTY COVERAGE IF YOUR LAWN AND GARDEN EQUIPMENT ENGINE OR A PART HAS FAILED DUE TO ABUSE NEGLECT IMPROPER MAINTENANCE OR UNAPPROVED MODIFICATION YOU ARE RESPONSIBLE FOR PRESENTING YOUR LAWN AND GARDEN EQUIPMENT ENGINE TO A KOMATSU ZENOAH Co DISTRIBUTION CENTER AS SOON AS A PROBLEM EXISTS THE WARRANTY REPAIRS SHOULD BE COMPLETED IN A REASONABLE AMOUNT OF TIME NOT TO EXCEED 30 DAYS IF YOU HAVE ANY QUESTIONS REGARDING YOU WARRANTY RIGHTS AND RESPONSIBILITIES YOU SHOULD CONTACT KOMATSU ZENOAH AMERICA INC AT 770 381 5147 RedMax 2 YEAR LIMITED WARRANTY EMISSION RELATED PARTS FOR TWO 2 YEARS FROM THE DATE OF ORIGINAL DELIVERY KOMATSU ZENOAH AMERICA ING THE COMPANY THROUGH AN
19. Y RedMax DEALER WILL REPAIR OR REPLAGE FREE OF CHARGE FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND OR WORKMANSHIP EMISSION RELATED PARTS ARE THE CARBURETOR ASSY COIL ASSY ROTOR SPARK PLUG AIR FILTER FUEL FILTER INTAKE MANIFOLD AND THE GASKETS ALL OTHER PARTS EXCEPT ABOVE PARTS FOR TWO 2 YEARS OF HOME USE ONE 1 YEAR FOR ANY OTHER USE FROM THE DATE OF ORIGINAL ANY DELIVERY THE COMPANY THROUGH ANY RedMax DEALER WILL REPAIR OR REPLAGE FREE OF CHARGE FOR THE ORIGINAL PUSHCHASER ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND OR WORKMANSHIP THIS IS THE EXCLUSIVE REMEDY THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION THAT A WARRANTED PART ID DEFECTIVE IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANGE OF THE REQUIRED MAINTENANGE AS DEFINED BY THE MANUFACTURER IN THE OWNER OPERATOR MANUAL ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLAGEMENT AS REQUIRED MAINTENANGE OR WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF REPAIR OR REPLACE AS NECESSARY SHALL BE WARRANTED FOR THE WARRANTY PERIOD ANY WARRANTED PART WHICH IS SCHEDULED FOR REPLAGEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF TIME UP TO THE FIRST SCHEDULED REPLAGEMENT PO
20. allic parts reach high temperatures during operation and doing so could result in serious burns y abi ENEN e When you finish trimming in one location and wish to continue work in another spot turn off the engine place the protective cover over the blades and turn the hedge trimmer so that the blades face away from your body before carrying it to the new location e Never transport the hedge trimmer over rough roads over long distances without first removing all fuel from the fuel tank as doing so might cause fuel to leak from the tank as a result of shocks absorbed during transport A Safety Precautions M NOTES ON CARE AND MAINTENANCE OF YOUR HEDGE TRIMMER In order to maintain your hedge trimmer in proper working order perform the maintenance and checking operations described in this manual at regular intervals In the event that any parts must be replaced or any maintenance or repair work not described in this manual must be performed please contact a representative from the store nearest RedMax authorized Servicing dealer for assistance Under no circumstances should you ever take apart the hedge trimmer or alter it in any way Doing so might result in the hedge trimmer becoming damaged during operation or the hedge trimmer becoming unable to operate properly Always be sure to turn off the engine before performing any maintenance or checking procedures When sharpening removing or reattachi
21. ate Upper blade Upper blade Lower blade Lower blade Washer Screw 19mm long Screw 29mm long Screw 22mm long Felt Plate Screw Bearing Lower case Bolt Bolt Rod Gear comp Pinion Fitting Bearing Bearing Plate Nut Nut Clutch drum Upper case Bolt Left handle comp Plate Bracket Nut Collar Washer Bolt Bolt Snap ring Band Bolt Lever ass y Protector Tool set Spanner e Socket e Screwdriver Switch Plate Washer Nut Cap Cover blade Cover blade Wrench Wrench 3883 12101 3883 12130 3880 11750 3885 11750 3883 11612 3927 11612 3880 11720 3927 11720 3880 11730 3927 11730 3880 11780 3884 11750 6095 11810 3884 11660 3873 11320 3880 11340 0260 00305 06001 00608 3873 11210 0225 10516 0225 10520 3873 11500 6830 11400 3884 11420 3199 13350 06001 00608 06004 06001 3876 11670 3880 11790 3880 11140 3884 11410 3887 11111 0212 50530 6830 13100 6095 13310 6095 13320 3876 14470 6095 13330 6095 13360 0225 10625 3883 12140 04064 02512 3880 13350 0225 10614 3881 13210 3887 91170 1111 91003 3540 91120 1110 91320 1030 91340 1059 72210 1120 72110 1520 72220 1520 72230 3422 72250 3880 91140 3927 91140 3880 95020 3880 95010 M M M M NM sts Q mm HN OBR ND AH PD H NU SN ni ANN ON SH si NA ii r 1 a 1 nm mm O a NDLR ND py H mm aNNO NN rnb OOD 1 r A i se Optional part Optional part Parts
22. g the engine place the body of the hedge trimmer onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the blades nor the throttle come into contact with any obstacles when the engine starts up e Never place the throttle into the high speed position when starting the engine After starting up the engine check to make sure that the blades stop rotating when the throttle is moved fully back to its original position If the blades continue to rotate even after the throttle has been moved fully back turn off the engine and take the unit to your authorized RedMax servicing dealer for repair E AVOID NOISE PROBLEM NOTE Check and follow the local regulations as to sound level and hours of operations for hedge trimmer In general operate hedge trimmers between 8a m and 5p m on week days and 9a m to 5p m weekends Avoid using hedge trimmer late at night and or early in the morning Safety Precautions M THINGS TO BE CAREFUL ABOUT WHEN USING YOUR HEDGE TRIMMER When using your hedge trimmer grip the handles of the hedge trimmer firmly with both hands place your feet slightly apart slightly further apart than the width of your shoulders so that your weight is distributed evenly across both legs and always be sure to maintain a steady even posture while working eMaintain the speed of the engine at the level required to perform trimming work and never rai
23. mp CHT2300L 49A 49B 22 Parts List Fig 3 CUTTER GROUP CHT2300B amp CHT2300L Q ty Key Description Part Number oy o 1 1 NOUS D gt Rear handle ass y e Screw M4x10 e Plate e Cable end Switch ass y e Throttle lever Snap ring e Pin Spring e Cap e Screw M4x16 e Screw M4x30 e Nut M6 Bolt M6x50 Nut M6 Bolt M6x40 Clutch drum Middle case Bolt M6x35 Front handle Bolt M6x14 Nut M5 Nut M6 Nut M6U Guide plate Guide plate Grease fitting Bearing 6001 2RS Bearing 608Z Pinion Gear comp Rod ass y Upper blade Upper blade Bearing 608Z Screw M3x5 Plate Felt Lower blade Lower blade Lower case Bolt M5x16 Bolt M5x20 Washer Screw M6x19 Plate Snap ring Tool set e Screwdriver e Socket Hex 3 4 Spanner 8x10 Cover blade Cover blade Screw M6x22 Stopper Spring Wrench Wrench 6845 13100 3873 13180 3873 13170 3873 13210 6845 13130 3873 13221 3873 13230 3873 13140 3873 13150 3873 13160 3873 13240 3873 13250 0280 10403 0225 50650 0280 10605 0225 50640 3884 11410 3873 11111 0225 30635 3873 12102 0225 10614 3880 11140 0280 10605 3880 11790 3873 11613 3929 11612 3199 13350 06004 06001 06001 00608 3884 11420 6830 11400 3873 11500 3879 11720 3929 11720 06001 00608 0260 00305 3880 11340 3873 11320 3879 11730 3929 11730 3873 11210 0225 10516 0225 10520 3873 11780 3884 11750 3876
24. n work is to be performed simultaneously by two or more persons care should also be taken to constantly look around or otherwise check for the presence and locations of other people using hedge trimmers within the work area so as to maintain a distance between each person sufficient to ensure safety Before beginning work each component of the hedge trimmer should be checked to make sure that it is in proper working order and to make sure that there are no loose screws or bolts fuel leaks ruptures dents or any other problems which might interfere with safe operation Be especially careful at this time to check that there is nothing wrong with the blades or with the joints by which the blades are attached to the hedge trimmer Never use the hedge trimmer when the blades have been worn down severely or when there is any sort of damage which has occurred to the blade mechanism Check to make sure that the handle grip and the protective cover have not come loose before using the hedge trimmer Bi THINGS TO CHECK BEFORE STARTING UP THE ENGINE Take a careful look around to make sure that no obstacles exist within a perimeter of 15 feet 5m or less around the hedge trimmer before starting the engine The RedMax hedge trimmer is equipped with a centrifugal clutch mechanism which causes the cutting blades to begin to rotate as soon as the engine is started by putting the throttle into the start position When startin
25. nd nuts Do not tighten up those screws or the blades will be locked and result in clutch failures Allow the screws a half spare turn and secure there with the nut See NOTE on page 8 W GEAR CASE e At every 25 hours of use supply grease to the gear case Pump in grease via the grease fitting until it comes out of the root of blades GREASE FITTING CHT2300 E AIR FILTER The air filter if clogged will reduce the engine performance Monthly check and clean the filter element in warm soapy water as required Dry completely before installing If the element is broken or shrunk replace with a new one FILTER ELEMENT CHT2300 E FUEL FILTER e When the engine runs short of fuel supply check the fuel cap and the fuel filter for blockage E SPARK PLUG Starting failure and mis firing are often caused by a fouled spark plug Periodically clean the spark plug and check that the spark gap is in the correct range For a replacement plug use the correct type specified by RedMax See SPECIFI CATIONS on the page 15 025 in 0 65 mm REPLACEMENT PLUG IS A CHAMPION RCJ6Y OR THE EQUIVALENT SUCH AS BOSCH WR8E OR NGK BR6S IMPORTANT e Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged e To install the spark plug first turn the plug until it is finger tight then tighten it a quarter t
26. ner to avoid mixing up with gasoline or other containers 6 Indicate the contents on outside of container for easy identification E FUELING THE UNIT 1 Untwist and remove the fuel cap Rest the cap on a dustless place 2 Put fuel into the fuel tank to 80 of the full capacity 3 Fasten the fuel cap securely and wipe up any fuel spillage around the unit 1 Select bare ground for fueling 2 Move at least 10 feet 3 meters away from the fueling point before starting the engine 3 Stop the engine before refueling the unit FOR YOUR ENGINE LIFE AVOID 1 FUEL WITH NO OIL RAW GASOLINE It will cause severe damage to the internal engine parts very quickly 2 GASOHOL It can cause deterioration of rubber and or plastic parts and disruption of engine lubrication 3 OIL FOR 4 CYCLE ENGINE USE or WATER COOLED 2 CYCLE ENGINE USE It can cause spark plug fouling exhaust port blocking or piston ring sticking 4 Mixed fuels which have been left unused for a period of one month or more may clog the carburetor or result in the engine failing to operate properly 9 Operation HM STARTING ENGINE Keep the blades clear of the surrounding as they will start moving upon starting of the engine When first starting up after putting fuel into the machine push the priming pump until fuel runs out in the clear tube Then close the choke Choking may not be necessary when re starting right after stopping the e
27. new seal s in the required location s E Notes on types of warnings Instructions labeled as shown at left concern critical steps or procedures which must be followed in order to prevent accidents which could lead to serious bodily injury or death This mark is used to indicate instructions which must be followed without exception IMPORTANT Instructions labeled as shown at left concern steps or procedures which if not followed correctly could lead to mechanical failure breakdown or damage Used to label supplementary instructions designed to provide hints or directions useful in the use of the product CONTENTS SAFETY PRECAUTIONS 2 PROPER AND SAFE OPERATION OF YOUR HEDGE TRIMMER WORK GEAR AND CLOTHING WARNINGS CONSIDERING HANDLING OF FUEL THINGS TO CHECK BEFORE USING YOUR HEDGE TRIMMER THINGS TO CHECK BEFORE STARTING UP THE ENGINE AVOID NOISE PROBLEM THINGS TO BE CAREFUL ABOUT WHEN USING YOUR HEDGE TRIMMER NOTES ON CARE AND MAINTENANCE OF YOUR HEDGE TRIMMER SETUP ee 7 HT2300A HT2300L CHT2300B CHT2300L FUEL de 9 HOW TO MIX FUEL FUELING THE UNIT PENN 10 STARTING ENGINE STOPPING ENGINE ADJUSTING IDLING SPEED HOW TO USE MAINTENANCE fri ia at a dra dada 12 DAILY INSPECTION GEAR CASE AIR FILTER FUEL FILTER SPARK PLUG MUFFLER SPARK ARRESTER INTAKE AIR COOLING VENT PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE STORAGE ilaria 14 SPECIFICATIONS
28. ng the blades be sure to wear thick sturdy gloves and use only proper tools and equipment to prevent injury When replacing blades or any other parts or when replacing the oil or any lubricants always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax hedge trimmer Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit Set up MHT2300A HT2300L 1 Join the engine unit to the clutch housing of the cutter unit with the fuel tank on the blade side 2 Align the mounting holes and tighten the engine securely with the 3 screws 3 Remove the right handle mounting screw nut and washer casually attached on the blade beam 4 Set the right handle on the beam making the grip come to the opposite side of the cutting teeth and attach with the hardware removed before When fastening the nut hold the screw to keep the blade washer loose Keep Loose NOTE eTo assure designed cutting performance always keep a half spare turn for the blade Screws It will cause blade seizure and premature wear of the clutch system if they are too tight Too loose screws will make the gap between the blades large and result in poor cutting performance 5 Install the left handle to the bracket attached to the clutch housing Use the hardware as shown below BOLT PLATE To e NUT BRACKET 6 Attach the th
29. ngine CLOSE OPEN 4m NO Pull the throttle lever and push the lock button to set the lever in the START position 3 CHT2300B CHT2300L only Slide the ignition switch to the engine side to set it in the ON position 4 Rest the unit on a flat firm place While holding the unit with your left hand on the starter housing pull the starter knob quickly ve HT2300 NOTE e Avoid pulling the rope to its end or returning it by releasing the knob Such actions can cause starter failures 5 When the engine has started gradually open the choke 6 Allow the engine to warm up for a half minute before starting operation NOTE elf the engine won t start after several attempts open the choke and repeat pulling the rope or remove the spark plug and dry it H STOPPING ENGINE 1 Release the throttle lever and run the engine at idling speed for a half minute 2 Stop the engine by the stop switch HT2300A HT2300L Press on the stop button until the engine stops completely STOP BUTTON CHT2300B CHT2300L Shift the ignition switch to the STOP position NOTE eExcept for an emergency avoid stopping the engine while running it at high speed Operation W ADJUSTING IDLING SPEED 1 When the engine tends to stop frequently at idling mode turn the idle set screw clock wise 2 When the cutting blades keep moving after releasing the throttle trigger turn the idle set screw
30. rottle lever and the engine Stop switch to the left handle and connect the throttle cable and the switch wire Put the rubber cap onto the switch button Hold the wires at the lower part of the handle using the tie band STOP SWITCH ie goa CAP THROTTLE LEVER TIE BAND 7 Check the cable play and if necessary adjust between 04 and 08 1 2mm by bending throttle wire receiver of the bracket with a nipper Set up m CHT2300B CHT2300L 1 Attach the engine to the clutch housing of the cutter unit Casually fix the front 2 points with the screws 55 long 15mm long 2 After connecting the ground wire install the rear handle to the clutch housing with the screw 2 long 50mm long and the nut 3 Put the screw 1 6 long 40mm long through the ground wire terminal and the rear handle and in to the engine mounting base Securely tighten all of the engine mounting screws 4 Attach the front handle onto the gear housing and fasten with 2 screws 1 2 long 30mm long and nuts 5 Connect the throttle cable with the lever on the rear handle and secure the end with the hardware attached to the handle 6 Check the cable play and if necessary adjust between 04 and 08 1 2mm by bending throttle wire receiver of the bracket with a nipper Fuel Gasoline is very flammable Avoid smoking or bringing any flame or sparks near fuel Make sure to stop the engine and allow it cool before refueling the
31. se the speed of the engine above the level necessary Always be sure never to allow other persons to come within the work area while trimming e Be especially careful not to slip if it is raining or if rain has just stopped as the ground is likely to be slippery at such times elf a branch or other object gets caught in the blades during operation always be sure to turn off the engine before removing the object Guard against hazardous situations at all times Warn adults to keep pets and children away from the area Establish a safe method for gaining your attention during operation Be careful if you are approached eTo protect yourself against injury from falling branches always be sure to wear the required safety equipment and be careful when working to watch to see in which direction branches are moving and falling so as to avoid being hit by falling branches If someone calls out or otherwise interrupts you while working always be sure to turn off the engine before turning around e Keep operation area clear of all persons particularly small children and pets Injury may result from flying debris Never touch the spark plug or plug cord while the engine is in operation Doing so may result in being subjected to an electrical shock s4 e eNever touch the muffler spark plug or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine These met
32. somewhere around 30 40 minutes per session and take 10 20 minutes of rest between work sessions Also try to keep the total amount of work performed in a single day under 2 hours or less A Safety Precautions EWORK GEAR AND CLOTHING When using your hedge trimmer always be sure to wear strong durable work clothing shirts should be long sleeved shirts and pants should be full length pants reaching down to the ankles e Always be sure to wear and helmet and face protector when using your hedge trimmer When using your hedge trimmer always be sure to wear thick work gloves to protect your hands and non slip sole work boots to prevent you from slipping Never use your hedge trimmer when wearing pants with loose cuffs when wearing sandals or when barefoot eWhen using your hedge trimmer for an extended period of time you should wear ear protectors to protect yourself from loss of hearing from overexposure to high levels of sound Face protector Helmet N Ear protectors Work gloves Work clothing Work boots W WARNINGS CONSIDERING HANDLING OF FUEL e The engine of the RedMax hedge trimmer is designed to run on a mixed fuel which contains highly flammable gasoline This fuel is highly flammable and you should never store cans of fuel or refill the tank of the hedge trimmer in any place where there is a boiler stove wood fire electrical sparks welding sparks or any other source of heat or fire
33. tie au moment de l achat Veuillez la remplir et l adresser RedMax KOMATSU ZENOAH AMERICA sous sept 7 jours en prenant soin de conserver une copie pour vous amp KOMATSU ZENOAH AMERICA INC P 4344 Shackleford Road Suite 500 Norcross Georgia 30093 Emission Control Label IMPORTANT ENGINE INFORMATION INFORMATION IMPORTANTE CONCERNANT LE MOTEUR THIS ENGINE CONFORMS TO U S EPA Ce moteur conforme aux normes U S EPA PH1 pour PH1 FOR SMALL OFF ROAD ENGINES les petits moteurs tout terrain ENGINE FAMILY 1KZXS 0254CD EM Type de moteur 1KZXS 0254CD EM ENGINE DISPLACEMENT 22 5cc Cylindr e du moteur 22 5 cc REFER TO OWNER S MANUMAL FOR MAINTE Se r f rer au Manuel de l utilisateur pour NANCE SPECIFICATIONS AND ADJUSTMENTS les sp cifications d entretien et les r glages ZENORH KOMATSU ZENOAH GO ZENORH KOMATSU ZENOAH GO RedMax Made in Japan RedMax Made in Japan Cr KOMATSU 7ENOAH AMERICA INC 4344 Shackleford Road Suite 500 Norcross Georgia 30093 O Printed in Japan
34. urn more with a socket wrench Maintenance am MUFFLER e Inspect periodically the muffler for loose fasteners any damage or corrosion If any sign of exhaust leakage is found do not use the hedge trimmer and have it repaired immediately Note that failing to do so may result in the engine catching on fire EH SPARK ARRESTER e The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet Periodically inspect and clean as necessary with a wire brush In the State of California it is required by law Section 4442 of the California Public Resources Code to equip a spark arrester when a gas powered tool is used in any forest covered brush covered or grass covered unimproved land SPARK ARRESTER E INTAKE AIR COOLING VENT e Never touch the cylinder muffler or spark plugs with your bare hands immediately after stopping the engine The engine can become very hot when in operation and doing so could result in severe burns When checking the hedge trimmer to make sure that it is okay before using it check the area around the muffler and remove any wood chips or leaves which have attached themselves to the hedge trimmer Note that failing to do so could cause the muffler to become overheated and that this in turn could cause the hedge trimmer to catch on fire Always make sure that the muffler is clean and free of wood chips leaves and other waste before use
35. which might ignite the fuel e Smoking while operating the hedge trimmer or refilling its fuel tank is extremely dangerous Always be sure to keep lit cigarettes away from the hedge trimmer at all times When refilling the tank always turn off the engine first and take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling If any fuel spillage occurs during refueling always be sure to use a dry rag to wipe any fuel which has been spilled onto the hedge trimmer before turning the engine back on again e After refueling screw the fuel cap back tightly onto the fuel tank and then carry the hedge trimmer to a spot 10 feet or more away from where it was refueled before turning on the engine Safety Precautions M THINGS TO CHECK BEFORE USING YOUR HEDGE TRIMMER Before beginning work look around carefully to get a feel for the shape of the land the trees or hedges to be trimmed and whether or not there are any obstacles which might get in the way while working and remove any obstacles which can be cleared away before beginning work The area within a perimeter of 50 feet 15m of the person using the hedge trimmer should be considered a hazardous area into which no one should enter while the hedge trimmer is in use and when necessary yellow warning rope warning signs or some other form of warnings should be placed around the perimeter of the area Whe
Download Pdf Manuals
Related Search