ASA Electronics AOM-701 Owner`s manual
Contents
1. junction box and camera mounting locations 2 Install all required cables in vehicle 3 2 19mm hole should be drilled for passing cables through vehicle walls barriers etc After the intermediate cable is passed through the hole install the split grommet included If additional cable protection is required install convoluted tubing over the cable 3 After cable wiring has been routed and components are in place temporarily make all system connections and perform a system function check If system does not operate properly see the troubleshooting section of this manual 4 If using an optional PanaVise stalk mount available separately use the mounting template provided on page 11 Install the PanaVise mount to the LCD monitor using the 10 self drilling screws included Important Do not use screws other than those provided with the AOM701 p p Void of warranty and serious product damage will occur 5 There are 2 options for connecting the LCD monitor to the connection cable If the application is such that the monitor is in close proximity to the connection cable the AOM701 monitor can be connected directly to the connection cable If the connection cable is mounted further from the monitor use the 5 intermediate cable included with the AOM701 to connect the monitor to the connection cable If more cable length is needed additional 5 lengths of the intermediate cable can be purchased See the accessory2. O 1 1 1 1 LIAD 4 5 INTERMEDIATE HARNESS 8 X 34 SELF DRILL BLACK SCREWS QTY 1 HARDWARE BAG 4 10 X 5 16 PHP THREAD FORMING BLACK SCREW LUD HARDWARE BAG POWER HARNESS QTY 1 4 SPLIT GROMMET DISTANCE MARKER CONNECTION CABLE 1 O D 3 16 I D STICKER QTY 1 1 QTY 1 SCOT gt 4 BLACK WIRE TIE QTY 4 CONTROLS AND OPERATION 1 Power Stand By Button The Power Stand by Button has two possible operations modes a Manual mode Turned on manual by the user by pressing the Power 1 button b Stand by mode Turned on by a stand by trigger wire generally connected to the vehicles 12V reverse backup lights Manual Mode wiring For manual mode operation the AOM701 should be wired as follows ACC 12V Red wire should be connected to the vehicles accessory feed GND ground wire should be connected to chassis ground Standby Mode wiring For Standby mode operation the AOM701 should be wired as follows ACC 12V Red wire should be connected to the vehicles accessory feed GND ground wire should be connected to chassis ground Standby Reverse trigger blue wire should be connected to the reverse feed of the
3. R WIDTH OF VEHICLE FIGURE A JC936369C 9C FIGURE B PANAVISE MOUNT TEMPLATE OPTIONAL ACCESSORY TROUBLESHOOTING SYMPTOM CAUSE SOLUTION No power No 12V accessory No Replace circuit fuse monitor has protection ground mis wired reversed device built in reset check ground connection verify power is being supplied Video No audio Blue white audio trigger wire Connect to 12V ACC or reverse light circuit not powered Volume adjust down turn volume adjustment up Monitor does not Blue standby wire not powered Connect to reverse circuit 12V activate in Standby reverse trigger Negative dark Low voltage Brightness Check voltage power and ground connections video image adjustment down turn brightness adjustment up No video no audio Camera connection Check camera input selection connection to camera and junction box correct camera connection plugged incorrectly Vehicle battery drained 12V ACC red wire connected to vehicle battery Provide 12V ACC red wire power from switched circuit 11 PRODUCT SPECIFICATIONS LCD panel specifications Size Type 7 diagonal TFT LCD Brightness 350 nit min 420 nit typ Contrast Ratio 200 min 300 typ View Angles 12 o clock 30 min CR210 Bottom 6 o clock 50 min Horizontal 50 min Response Ti
4. Voyager AOM701 7T FLAT PANEL COLOR OBSERVATION MONITOR OWNER S MANUAL zz 63963630309 AOM701 Features T High Performance Color LCD Built in Audio Speaker with Volume Control and 12V Trigger 2 Camera A V Input with A B Select Control Backlit Controls and Day Night Picture Modes for Nighttime Use Auto Manual Power On Sun Visor Included Visit us at http www asaelectronics com Patent Pending Important Please Read This Manual Before Installing Congratulations on your purchase of a Voyager AOM701 LCD Observation Monitor With proper installation and use your AOM701 is designed to provide you with years of trouble free operation This manual contains important information required to properly install and operate the unit Please read this manual thoroughly before beginning All Voyager Observation products are strictly intended to be installed as a supplement aid to standard rear view mirror systems that may already exist in your vehicle Voyager observation products are not intended for use as substitutes for rear view mirror devices or for any other standard motor vehicle equipment required to be installed on vehicles by law While Voyager observation products contribute to improving the vehicle operator s field of view these products are no substitute for proper defensive driving techniques and observance of traffic laws and motor vehicle
5. e unit will exit the Picture Adjustment mode Volume Buttons This 2 button set of controls adjusts the output volume of the built in audio speaker when the audio function is enabled see typical system connection diagram The button increases output volume The button decreases output volume Volume level is indicated by the OSD bar graph at the bottom of the screen These buttons also serve as adjustment controls while in the Picture Adjustment Menu mode see above section for details Note The AOM701 requires 12V to be applied to the Audio Enable trigger input in order to activate the built in speaker If no audio output is heard from the speaker regardless of the volume level adjustment check this connection INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLATION Before drilling be sure that no cable or wiring is on the other side Clamp all wires securely to reduce the possibility of them being damaged during installation and use Keep all cables away from hot or moving parts and electrically noisy components Wiring Definitions Power connection 1 ACC 12 Red Pin2 Standby Trigger Blue wire Pin3 Ground Black wire Pin4 Audio Trigger Blue w white stripe wire m Camera A input Connection for camera or camera extension cable m Camera B input Connection for camera or camera extension cable LCD panel 12 pin DIN cable connection Procedure 1 Choose the monitor
6. list at the back of this manual for part number details 6 Connect the 4 pin power harness to vehicle See system connection illustration page 8 7 Plug camera extension cable available separately into AV1or AV2 input connector on the connection cable Plug observation camera into camera extension cable 8 Make sure all cables are routed away from hot or moving parts and away from sharp edges Secure cables with wire ties 9 For rear observation applications range marker stickers have been included with this product These markers are designed to adhere to your LCD monitor and provide a reference for gauging distance See page 9 for illustration showing proper use and installation of the range markers 318V9 31VIQ3WH3INI S NOIL03NN09 L GNNOYD SISSVHO 6I0v 18 B YOLINOW 097 LOZNOY gt ads Mas 1 98 U09 aiqejiene ajqeo jeuondo SWALI AH0SS399V NOLLOSNNOO WALSAS TVOIdAL REAR OBSERVATION INSTALLATION DISTANCE MARKER USE INSTALLATION PLACE INDICATOR MARKERS CONE BOX ANY REFERENCE OBJECT HANDY BEHIND VEHICLE AS IN FIGURE A PLACE RANGE MARKER DECALS ON SCREEN OF MONITOR OVER IMAGE OF INDICATOR MARKERS ON GROUND BEHIND VEHICLE AS VIEWED ON THE MONITOR SCREEN THIS GIVES YOU A VISUAL REFERENCE OF ACTUAL DISTANCE BEHIND VEHICLE AS OBJECTS ARE VIEWED INDICATO
7. me Rise 12ms typ 50ms max Fall 18ms typ 60ms max Back light CCFL Back light Life 30k hrs min 40k hrs typ Operation Temperature Range 20 C to 65 C Storage Temperature Range 40 C to 80 C Max Humidity 100 RH Max Vibration Force 2 5G Max Shock Force 100G Operating Voltage Range 11VDC to 26VDC Current Draw typical 50mA Idle 1 50A typ 1 70A max Signal System NTSC Video Aspect Ratio 16 9 Input format Composite NTSC Input level 1Vp p into 75Q Audio Input level 10dBV nominal 317mV Product Weight 3 0165 approximate Product Overall Dimensions 7 197mm W x 5 4 134mm H x 1 3 16 29 5mm D Visit us at http www asaelectronics com 12
8. safety regulations Warnings Installation Location It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped with a television viewer or screen located at any point forward of the back of the driver s seat or in any location that is visible directly or indirectly to the driver while operating the vehicle The AOM701 product is designed to be used primarily as a rear observation device in conjunction with closed circuit cameras In any installations where the AOM701 is used to display television broadcasts or recorded video playback installation location must adhere to local laws and regulations Tampering To prevent electrical shock DO NOT OPEN THE MONITOR CASE There are potentially harmful voltages inside the monitor There are no user serviceable parts inside If evidence of tampering is detected the warranty will be considered void Moisture Your Voyager AOM701 was designed to be water resistant While it will withstand short periods of exposure to moisture this product does contain sensitive electronic components and exposure to moisture should be limited by the user installer This product is not designed for applications where constant exposure to moisture or immersion can be encountered This unit should NEVER be cleaned with a power washer or used where direct power washer spray may be encountered PACKING CONTENTS olaaa ae WARRANTY CARD LCD MONITOR SUN SHIELD 4 X 2 VELCR
9. vehicles backup lighting system The power button 1 features dual illumination It will be brighly lit when the unit is turned on and will be dimly lit when the unit is turned off When the unit is turned on all other buttons will be illuminated When off only the Power button will be lit Note Please note that when the unit is in the standby mode trigger wire is triggered the Power button 1 will not function 2 3 A B Input Select Button This control toggles the active display image back and forth between AV1 and AV2 inputs AVI is the default source for the Blue Stamdby trigger wire Day Night Mode Button This control toggles the unit between Day and Night LCD illumination modes In the Day mode the LCD backlight intensity is at maximum In Night mode the LCD backlight is dimmed to a preset level that is more suitable for low light operation Picture Adjustment Menu Button This control accesses an On Screen Display OSD menu for four LCD picture adjustments Brightness Contrast Color and Tint The first depress of the button accesses the Brightness adjustment The Volume controls adjust the level which is indicated by the bar graph at the bottom of the screen Each consecutive depress of the Picture button accesses the adjustment screen for each picture adjustment If no buttons are pressed within 6 seconds or controls other than the Picture and Volume buttons are pressed th
Download Pdf Manuals
Related Search