Makita HM1317CB Instruction manual
Contents
1. e Tr a k ta SYS AN SA Y En Aw 010282 E DOUBLE INSULATION nd UNDERSTAND before using OR FUTURE REFERENCE ENGLISH SPECIFICATIONS Model HM1317C HM1307C HM1317CB HM1307CB Blows per minute 730 1 450 Overall length 715 mm 849 mm Net weight 17 0 kg 15 3 kg 19 1 kg 17 5 kg Safety class By Due to our continuing programme of research and development the specifications herein are subject to change without notice Note Specifications may differ from country to country Weight according to EPTA Procedure 01 2003 END201 4 Symbols The following show the symbols used for the equipment Be sure that you understand their meaning before use Read instruction manual 8 DOUBLE INSULATION X Only for EU countries Do not dispose of electric equipment together with household waste material In observance of European Directive 2002 96 EC on waste electric and electronic equipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility ENE045 1 Intended use The tool is intended for chiselling work in concrete brick stone and asphalt as well as for driving and compacting with appropriate accessories ENF002 1 Power supply The tool should be connected only to a power supply of the sa2. 2 Vibration The vibration total value tri axial determined according to EN60745 Work mode chiseling function with side handle Vibration emission an cheg 8 5 m s Uncertainty K 1 5 m s vector sum For Model HM1317CB ENG102 2 For European countries only Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 81 dB A Sound power level Lwa 101 dB A Uncertainty K 3 dB A Wear ear protection ENG216 2 Vibration The vibration total value tri axial determined according to EN60745 Work mode chiseling function with side handle Vibration emission an cheg 7 0 m s Uncertainty K 1 5 m s vector sum ENH213 1 EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine s Designation of Machine Demolition Hammer Model No Type HM1307C HM1307CB HM1317C HM1317CB are of series production and Conforms to the following European Directives 2000 14 EC 98 37 EC until 28th December 2009 and then with 2006 42 EC from 29th December 2009 And are manufactured in accordance with the following standards or standardised documents EN60745 The technical documentation is kept by our authorised representative in Europe who is Makita International Europe Ltd Michigan Drive Tongwell Milton Keynes MK15 8JD England The conformity assessment procedure required by Directive 2000 14 EC was
3. and grease lubricating and GEB004 6 HAMMER SAFETY WARNINGS Wear ear protectors Exposure to noise can cause hearing loss Use auxiliary handle s if supplied with the tool Loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock 4 Wear a hard hat safety helmet safety glasses and or face shield Ordinary eye or sun glasses are NOT safety glasses It is also highly recommended that you wear a dust mask and thickly padded gloves 5 Be sure the bit is secured in place before operation 6 Under normal operation the tool is designed to produce vibration The screws can come loose easily causing a breakdown or accident Check tightness of screws carefully before operation 7 In cold weather or when the tool has not been used for a long time let the tool warm up for a while by operating it under no load This will loosen up the lubrication Without proper warm up hammering operation is difficult 8 Always be sure you have a firm footing Be sure no one is below when using the tool in high locations 9 Hold the tool firmly with both hands 10 Keep hands away from moving parts 11 Do not leave the tool running Operate the tool only whe
4. and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Service 24 25 26 Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Follow instruction for changing accessories Keep handles dry clean and free from oil
5. by turning the adjusting dial This can be done even while the tool is running The dial is marked 1 lowest speed to 5 full speed Refer to the table below for the relationship between the number settings on the adjusting dial and the blows per minute Number on adjusting dial Blows per minute 5 1450 4 1350 3 1150 2 800 1 730 For model HM1317C HM1317CB only NOTE Blows at no load per minute becomes smaller than those on load in order to reduce vibration under no load but this does not show trouble Once operation starts with a bit against concrete blows per minute increase and get to the numbers as shown in the table When temperature is low and there is less fluidity in grease the tool may not have this function even with the motor rotating A CAUTION The adjusting dial can be turned only as far as 5 and back to 1 Do not force it past 5 or 1 or the speed adjusting function may no longer work Indicator lamp 1 Power ON indicator lamp green 2 Service indicator lamp red The green power ON indicator lamp lights up when the tool is plugged If the indicator lamp does not light up the mains cord or the controller may be malfunction The indicator lamp is lit but the tool does not start even if the tool is switched on the carbon brushes may be worn out or the controller the motor or the ON OFF switch may be malfunction The red service indicator lamp flickers up when the
6. carbon brushes are nearly worn out to indicate that the tool needs servicing After approx 8 hours of use the motor will automatically be shut off ASSEMBLY A CAUTION Always be sure that the tool is switched off and unplugged before carrying out any work on the tool Side handle auxiliary handle 1 Set bolt 2 Nut 3 Side handle The side handle can be swung 360 on the vertical and secured at any desired position Just loosen the clamp nut to swing the side handle to a desired position Then tighten the clamp nut securely Installing or removing the bit For Model HM1307C HM1317C only 1 Bit 2 Tool retainer 3 Tool holder With the notched portion on the shank of the bit facing toward the tool retainer insert the bit into the tool holder as far as it will go Then pull out and turn the tool retainer 180 to secure the bit After installing always make sure that the bit is securely held in place by trying to pull it out For Model HM1307CB HM1317CB only 1 Bit with collar 1 2 Bit without collar This tool accepts bits either with or without a collar on its shank 1 For bits with a collar 1 Bit 2 Tool retainer 3 Tool holder 4 When the bit is inserted 5 When the bit is retained To install the bit follow either procedure 1 or 2 described below Pivot the tool retainer back and slightly downward Insert the bit into the tool holder as far as it will go To s
7. non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and care 17 20 21 22 23 Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous
8. ecurely retain the bit return the tool retainer to its original position ACAUTION Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure 2 For bits without a collar 1 Bit 2 Tool retainer 3 Tool holder 4 When the bit is inserted 5 When the bit is retained Pivot the tool retainer back and slightly downward With the notched portion of the bit facing the tool retainer shaft insert the bit into the tool holder as far as it will go Then pivot the tool retainer further downward toward the barrel to securely retain the bit ACAUTION Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure The bit without a collar cannot be retained by the method shown in Fig 1 To remove the bit follow the installation procedure in reverse OPERATION Chipping Scaling Demolition Always use the side grip auxiliary handle and firmly hold the tool by both side grip and switch handle during operations Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around uncontrolled Pressing very hard on the tool will not increase the efficiency MAINTENANCE ACAUTION Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance Lubrication ACAUTION This servicing s
9. hould be performed by Makita Authorized or Factory Service Centers only This tool requires no hourly or daily lubrication because it has a grease packed lubrication system However it is recommended to periodically replace the grease for longer tool life First switch off and unplug the tool For model HM1307C HM1307CB only 1 Rear cover 2 Hex wrench Remove the six screws using a hex wrench and remove the rear cover 1 Crank cap Pull out the crank cap in the direction of arrow and remove it 1 Hammer grease Then replenish with fresh grease 60g Use only Makita genuine hammer grease optional accessory Filling with more than the specified amount of grease approx 60 g 2 oz can cause faulty hammering action or tool failure Fill only with the specified amount of grease To reassemble the tool follow the disassembling procedure in reverse For model HM1317C HM1317CB only 1 Rear cover 2 Hex wrench Remove the six screws using a hex wrench and remove the rear cover 1 Crank cap cover Pull out the crank cap cover in the direction of arrow and remove it 1 Hammer grease Then replenish with fresh grease 60g Use only Makita genuine hammer grease optional accessory Filling with more than the specified amount of grease approx 60 g 2 oz can cause faulty hammering action or tool failure Fill only with the specified amount of grease To reassemble the tool follow the disassembl
10. in Accordance with annex VIII Notified Body TUV Rheinland identification no 0197 Model HM1307C Product Safety GmbH Measured Sound Power Level 101dB Guaranteed Sound Power Level 103dB Model HM1307CB Measured Sound Power Level 101dB Guaranteed Sound Power Level 104dB Model HM1317C Measured Sound Power Level 101dB Guaranteed Sound Power Level 103dB Model HM1317CB Measured Sound Power Level 101dB Guaranteed Sound Power Level 104dB 8th April 2009 AR Tomoyasu Kato Director Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi JAPAN GEA005 2 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool Work area safety 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes 3 Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any
11. ing procedure in reverse ACAUTION Be careful not to damage the brush holder unit and carbon brushes especially when installing the rear cover Do not reuse the six bolts but use new ones in the reassembling since these bolts are applied with adhesive To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized Service Centers always using Makita replacement parts ACCESSORIES ACAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Bull point Cold chisel Scaling chisel Clay spade Rammer Hammer grease Safety goggles Plastic carrying case 11 Makita Corporation Anjo Aichi Japan 884923 224
12. me voltage as indicated on the nameplate and can only be operated on single phase AC supply They are double insulated in accordance with European Standard and can therefore also be used from sockets without earth wire For Model HM1307C ENG102 2 For European countries only Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 81 dB A Sound power level Lwa 101 dB A Uncertainty K 3 dB A Wear ear protection ENG216 2 Vibration The vibration total value tri axial determined according to EN60745 Work mode chiseling function with side handle Vibration emission ah cHea 12 5 m s Uncertainty K 2 0 m s vector sum For Model HM1307CB ENG102 2 For European countries only Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 81 dB A Sound power level Lwa 101 dB A Uncertainty K 3 dB A Wear ear protection ENG216 2 Vibration The vibration total value tri axial determined according to EN60745 Work mode chiseling function with side handle Vibration emission ah cneq 12 0 m s Uncertainty K 1 5 m s vector sum For Model HM1317C ENG102 2 For European countries only Noise The typical A weighted noise level determined according to EN60745 Sound pressure level Lpa 81 dB A Sound power level Lwa 101 dB A Uncertainty K 3 dB A Wear ear protection ENG216
13. n hand held 12 Do not point the tool at any one in the area when operating The bit could fly out and injure someone seriously 13 Do not touch the bit or parts close to the bit immediately after operation they may be extremely hot and could burn your skin 14 Do not operate the tool at no load unnecessarily 15 Some material contains chemicals which may be toxic Take caution to prevent dust inhalation and skin contact Follow material supplier safety data SAVE THESE INSTRUCTIONS ZA WARNING DO NOT let comfort or familiarity with product gained from repeated use replace strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury FUNCTIONAL DESCRIPTION ACAUTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch action 1 Switch lever ACAUTION Before plugging in the tool always check to see that the tool is switched off Switch can be locked in ON position for ease of operator comfort during extended use Apply caution when locking tool in ON position and maintain firm grasp on tool To start the tool push the switch lever ON 1 on the left side of the tool To stop the tool push the switch lever OFF O on the right side of the tool Speed change 1 Adjusting dial The blows per minute can be adjusted just
14. way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock If operating a power tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI protected supply Use of an GFCI reduces the risk of electric shock Personal safety 10 11 12 13 14 15 16 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use personal protective equipment Always wear eye protection Protective equipment such as dust mask
Download Pdf Manuals
Related Search