Miele T 4897 C Operating instructions
Contents
1. m Turn the lever on the condenser unit to the vertical position Cleaning and care If you cannot see any fluff m Replace the condenser unit see following page If you can see some fluff m Clean the condenser unit as described below Cleaning the condenser unit m When rinsing the condenser unit make sure you position it as shown in the next two illustrations m Pull the condenser unit out of its housing by the handle Checking the condenser unit m Use a shower head or similar to rinse the unit out as shown m Hold the condenser unit up to the light as shown m Check to see if there is any fluff inside it The arrows in the illustration above indicate where to look 33 Cleaning and care m Then flush the unit through from the front m Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone m Remove any soiling still visible inside the housing unit by hand using a damp cloth Do not try and access areas you cannot reach by hand m Also make sure the rubber seals are clean The rubber seals must not be removed and must be free of kinks 34 Replacing the condenser unit m With the handle facing upwards push the condenser unit back into position in its housing m Turn the lever down to the horizontal position making sure that the hook on the lever clicks into the groove When replacing2. Notes This programme includes a proofing fixing phase Only use proofing agents which are stated by the manufacturer as being suitable for use on membrane textiles as these contain fluorochemical compounds Do not dry items which have been treated with proofing agents containing parafin Fire hazard Pillows large 1 pillow up to 80 x 80 cm Pillows 1 2 pillows up to 40 x 40 cm Fabric type Pillows suitable for drying in a tumble dryer with feather down or synthetic fillings Notes Please observe the instructions on the care label Pillows can still feel damp after being dried You can use this programme several times until the pillow feels dry 26 Weight of dry laundry Changing the programme sequence To cancel a programme m Press short cut button Cancel The items will be cooled down depending how long they have been dried for and the temperature reached Finish will appear when you press short cut button Cancel again m Switch the tumble dryer off by pressing the D button m Switch the tumble dryer on again by pressing the D button m Select a different programme The programme will continue as long as the cooling down phase has not been reached To interrupt a programme m Switch the tumble dryer off by pressing the D button To continue drying m Switch the tumble dryer on again by pressing the D button Adding or
3. Important N Do not let the drain hose become kinked as this could damage it If you want to drain the water off into a sink you will need to secure the hose carefully e g by tying it to a tap to make sure it cannot slip during use Otherwise there is a risk of overflowing water which could cause damage Use the bow shaped guide to prevent the drain hose from becoming kinked see Front view illustration Installation Connection to a sink drain outlet The drain hose can be connected directly to a sink drain outlet m Remove the following from the back of the dryer at the bottom Adapter 1 and hose clip 3 behind it m Fit adapter 1 to the sink drain outlet using nut 2 If this nut has a flat disc in it you should take the disc out first Important if this nut has a washer or seal in it this must not be removed m Attach the end of the hose to adapter 1 m Use a screwdriver to tighten hose clip 3 up close to the nut If you no longer wish to use an external condensed water outlet N Do not push the drain hose back into the dryer Doing this could cause it to become kinked and damaged in the dryer m Loop the drain hose up m Use a suitable cable tie to secure the looped hose to the back of the dryer or simply lay the looped hose behind the dryer m Attach the open end of the drain hose back onto the holder at the back of the dryer at the top see holder 2 in Setting up the d
4. See the Warning and Safety section of this booklet for further details Energy saving tips To avoid unnecessarily long drying times and high consumption of energy Make sure that your laundry is thoroughly spun before drying The higher the spin the greater the savings that can be made in energy and time during drying Load according to the optimum amount of laundry recommended for the programme being used see Programme chart Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Make sure the room in which the dryer is located is well ventilated Make sure the fluff filters are clean before using the dryer Check the condenser unit from time to time and clean it when necessary Contents Caring for the environment is sss 2 Disposal of the packing material liiis 2 Disposal of your old appliance 0 2 0 0 0 eee 2 Energy SAVING TPS esere sache 2 Warning and Safety instructions lessen 6 Operating the tumble dryer liess 10 Control panels saa xg ee Re REG eR ea aaa a Age a AN eed 10 Display Re TEIG ee beh ee AEG re line 11 Using tor the TIESE UME uinea reg dex aep le kei la ia 13 Notes on laundry Care es 14 Ba jis u c r 14 Here elas BANG A TA tacked sists Suk tg stat BA AI ee TANNA 14 How to dry correctly
5. eee 15 Brierimsiruetions 3 2 paw oe dre ea 15 Favourite programmes e 18 Selecting changing a favourite iiie 18 Saving a favourite programme iilis 20 Extra options iilii s 21 OMON d e tor ES DR RC eee Phe BG qux DIRE Dad Yet ax eke ded dd 21 Low tempetalute vc as ed eee Tea beaded PEE ERR edd duh Lad 21 lm 22 Programme chart il lll es 23 Changing the programme sequence elei isses 27 To CANCEL a progamme ana namen Ro pn aan Fan kk eA dag 27 To interrupt aprogramme aka nn s ree xr nen 27 Adding or removing laundry after a programme has started 27 Electronic programme locking 000002 28 Contents Cleaning and care a 29 Emptying the condensed water container 0 0 i esses 29 Cleaning the fluff fillers ee m e 30 Cleaning them whilst dry 00 e 30 Cleaning them with water 0 0 ee 31 Cleaning the tumble dryer cee 31 Cleaning the condenser unit 000 eect eee 32 Removing the c ndenser nlt iis se ek RR EE E Re RO E Re Y RN 32 Checking the condenser unit eel ee 33 Cleaning the condenser unit liil ees 33 Replacing the condenser unit lile 34 Problem solving guide eese 35 Problemi solving guide assesses pee RE E eb de bed ora 35 Fault messages in the display iliis 35 Other problem
6. 06 581 410 00 en GB
7. AN Technical fault the programme is cancelled the buzzer sounds No obvious cause In some circumstances Clean the filters has already been displayed Clean the filters and the condenser unit To delete the fault message Switch the dryer off and then back on again There is a fault if despite doing this the programme is cancelled and the fault message appears again Contact the Miele Service Department 1 Programme finish time changed This is not a fault Settings were changed while the timer was counting down to the start of a programme or there was a power cut 36 Problem solving guide Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off In some circumstances the following message also appears Clean the filters Please check all the possible causes and switch the dryer off and then back on again Ventilation to and from the dryer may be insufficient e g because it is installed in a small room This has caused the temperature in the room to rise sharply Open a door or window while the machine is in operation for increased air flow The fluff filters are clogged up with fluff or were still wet when they were replaced Remove any fluff The fluff filters must be completely dry The laundry has not been spun sufficiently Make sure
8. 12 Operating the tumble dryer Using for the first time When the tumble dryer is switched on for the first time the welcome screen will appear The welcome screen will not appear again after you have entered the time of day and run an initial programme lasting longer than one hour Setting the time of day Please set the time of day m Set the hour with the multi function selector and confirm this setting Now set the minutes Once this has been confirmed the time of day is saved in memory and the display goes back to the entry menu Notes on laundry care Care symbols Before drying check the drying symbol on the care label If there are no symbols dry at your own risk les aces Dry at normal temperature o PIT Dry at a low temperature Dd AAN BATA Do not tumble dry Tips on drying Always observe the makimum recommended loads given in the Programme chart Never overload the drum Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing Do not put soaking wet items into the tumble dryer Spin them thoroughly after washing using the appropriate spin speed For delicates and fabrics with the following care label 4 select Low temperature Use the Automatic programme for drying mixed loads of cottons and minimum iron fabrics Open jackets so that they can dry evenly Woollens and wool blends
9. A buzzer sounds at intervals for a maximum of 1 hr to let you know the programme has finished Off The buzzer will always sound when there is a fault even if it has been switched off Normal The buzzer sounds at the end of a programme Loud The buzzer sounds louder at the end of a programme A tick will appear beside the option to show that it has been set The machine is delivered with the option Normal set as stan dard An audible tone sounds when the Start button a short cut button or the multi function selector is pressed A tick will appear beside the option to show that it has been set The machine is delivered with the option Off set as standard Display contrast There are ten different display contrast settings The bar chart shows you the setting 55 Settings menu Standby Miele home 56 To save energy the display goes out after 10 minutes and the Start button flashes slowly There are two options Active the machine is delivered with this option selected Standby is activated ifa programme is not selected after the machine has been switched on after the Start button has been pressed atthe end of a programme Not in current programme Standby is activated if a programme is not selected after the machine has been switched on Operating the multi function selector or one of the short cut buttons switches the display back on
10. Condensed water container Control panel Door 42 Service panel for condenser unit Four height adjustable screw feet External drainage options e g via wash basin wash basin drain outlet or gully Installation Installation site N Make sure the dryer door can be opened without hindrance after installation Room in which the dryer is located Air taken in for use in the drying process will be warm when it is expelled from the rear of the dryer This expelled air heats up the air in the room It is therefore very important to ensure that the room is adequately ventilated particularly if the dryer is located in a small room Otherwise running times and energy consumption could be increased Transporting the machine to its installation site When moving the machine you can hold it by the lid where it protrudes to the rear of the dryer To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet Aligning the machine The machine must be perfectly level to ensure safe and proper operation m The screw feet can be adjusted to compensate for any unevenness in the floor The ventilation gaps in the plinth must not be covered over as this would prevent a sufficient intake of air This tumble dryer is not suitable for building under due to its sloping facia Before moving the machine again e g when mo
11. cannot get trapped or damaged when the door is shut m Shut the door either with a gentle swing or lean against it and push it shut How to dry correctly Select a programme m You can select a programme either by using the appropriate short cut button to select one of the four most frequently used programmes favourites or by going into the Programme selection menu m f required you can then select any Extras and use the Timer from the relevant sub menu The Start button will flash as soon as a programme can be started Start the programme m Press the Start button The Start button will light up Programme start will appear in the display followed by Drying and the programme duration With sensor drying programmes the drying level reached e g Machine iron Hand iron 4 etc will show in the display Once drying is in progress you can press short cut Button Timer to call up the current time of day and the estimated end time of the programme Button Save to save the current programme as a favourite Button Cancel to cancel the current programme 16 Estimated time remaining When a programme is selected the estimated drying time will appear in the display Please be aware that it is only an estimate The following factors all affect the estimated time remaining residual moisture content after spinning type of fabric size of load
12. electrician The electrical safety of this machine can only be guaranteed when continuity is complete between it and an effective earthing system which complies with local and national regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock Do not connect the appliance to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating Warning and Safety instructions The machine is built in accordance with current safety requirements Unauthorised repairs could result in unforeseen dangers for the user for which the manufacturer cannot accept liability Repairs should only be undertaken by a Miele approved technician Ensure current is not supplied to the machine until after maintenance or repair work has been carried out Faulty components must only be replaced by genuine Miele original spare parts Only when these parts are fitted can the safety standards of the machine be guaranteed If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger In countries where there are areas which may be s
13. removing laundry after a programme has started m Press the oa button m Open the door N Do not touch the back of the drum when adding or removing items The drum could be very hot danger of burning m Add or remove items m Close the door To continue drying m Press the Start button The time left shown in the display may now vary from the actual drying time 27 Electronic programme locking Programme locking prevents the short cut buttons or the multi function selector being used while drying is in progress The door is not locked and can be opened at any time To activate programme locking m Once the programme has begun press and hold the Start button until the following appears in the display System locked Now no more alterations can be made to the programme Programme locking is deactivated automatically at the end of the programme or by pressing button o3 To deactivate programme locking m Press and hold the Start button until the following appears in the display 28 Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose see installation Empty the condensed water container after every drying programme The drying programme will be interrupted if the maximum level of the condensed water container is reached A message will appear i
14. Miele NAVITRONIC Operating instructions for condenser tumble dryer T 4897 C To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time M Nr 06 581 410 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure they are offered for recycling Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of your appliance with your household waste Please dispose of it at your local community waste collection recycling centre and ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person The plug must be rendered useless and the cable cut off directly behind it to prevent misuse
15. able proprietary stainless steel cleaner following the manufacturer s instructions Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic sufaces and other parts The machine must never be hosed down m Dry all parts with a soft cloth m A microfibre E Cloth is available from the Miele UK Spare Parts Department which is suitable for cleaning surfaces such as stainless steel glass plastic and chrome without the use of chemicals It can be washed 300 times 31 Cleaning and care Cleaning the condenser unit Detergent residue hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage Check the condenser unit at least twice a year If the dryer is used frequently then clean the condenser unit after approx 100 drying cycles Removing the condenser unit m Open the service panel by pressing the two lower corners at the same time see illustration The hooks at the side will prevent the panel from falling off m Now remove the panel by pulling it diagonally upwards m Then place it to one side 32 m Turn the lever on the inner cover downwards to the vertical position m Pull the cover forwards m Then remove it by pulling it diagonally upwards
16. abrics Shirts Max load 2 kg Normal Normal Hand iron 4 Fabric type Shirts and blouses Extra option Low temperature Low temperature cannot be deselected Denim Max load 3 kg Normal Hand iron 4 Fabric type Denim fabrics e g jeans jackets skirts shirts Extra option Low temperature Low temperature cannot be deselected Woollens handcare Max load 2 kg Fabric type Woollen fabrics Notes To refresh and fluff up woollen garments quickly Fabrics are not completely dried in this programme Remove garments as soon as the programme has finished and leave to finish drying at room temperature Extra options Low temperature Low temperature cannot be deselected Silks handcare Max load 1 kg Fabric type Silks e g blouses and shirts Notes Smooths out creasing Fabrics are not completely dried in this programme Remove garments as soon as the programme has finished and leave to finish drying at room temperature Extra option Low temperature Low temperature cannot be deselected Weight of dry laundry 24 Programme chart Smoothing Max load 3 kg Fabric type Cotton and linen fabrics Minimum iron items made of mixed fibres cottons or synthetics e g trousers jackets shirts Notes Smooths out creasing caused during the spin cycle in the was
17. again A tick V will appear beside the option to show that it has been set This setting does not apply to this model 57 58 59 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW tel Abingdon 01235 554455 Service Office 01235 554466 fax 01235 554477 Internet www miele co uk Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 46 10 710 Fax 01 46 10 797 Email info miele ie Internet http www miele ie Australia Miele Australia Pty Ltd A C N 005635398 1 Gilbert Park Drive Knoxfield VIC 3180 Telephone 03 9764 7100 Fax 03 9764 7129 Internet www miele com au Distributor New Zealand Steelfort Engineering Company Ltd 500 Rangitikei Street Palmerston North Priv Bag 11045 NZ Telephone 06 350 1350 Fax 06 356 1507 South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 011 548 1900 Telefax 011 548 1935 Internet www miele co za E mail info miele co za Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 67351191 Fax 65 67351161 Email infosea miele com sg Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk Alteration rights reserved 0905 M Nr
18. d be between 2 C and 35 C If the water is drained externally through the drain hose instead of being collected in the condensed water container make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage Condensed water is not drinking water It can cause health problems in both people and animals Always keep the area around the machine free of dust and fluff Dust drawn into the machine can over time cause blockages in the condenser unit Warning and Safety instructions To prevent the risk of fire the following textiles must not be dried in this machine fabrics which contain a large proportion of rubber foam rubber or rubber like materials items which contain padding or fillings e g pillows jackets items which have been treated with inflammable cleaning agents items which have been splashed with hair lacquer hair spray nail varnish remover or similar substances items which have been soiled with oils or residues containing grease Kitchen oils cosmetics etc items soiled with wax or other chemicals e g mops and floor cloths items which have not been thoroughly cleaned and which are still soiled with grease or oil e g workwear Such clothing may require a heavy duty detergent to get them clean If necessary consult the detergent manufacturer for advice Do not let anyone
19. de of the condenser unit housing Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract static charge Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing machine or a fabric conditioner sheet to the load in the dryer There is a build up of fluff Fluff is principally the result of friction when garments are being worn and washed Machine drying hardly causes any fluff to form and has been established by research institutes to have no appreciable effect on the lifetime of fabric Fluff is collected by the fluff filters and can be easily removed see Cleaning and Care Feather filled pillows smell after drying Feathers are a natural product and this is quite normal The smell will dissipate after sufficient airing 38 Problem solving guide Problem Possible cause Remedy The programme does not start and the display is dark No obvious cause Have you followed the correct procedure for using the machine Is the plug correctly inserted in the socket and switched on Is the appliance door closed properly Has the fuse or circuit breaker tripped The interior drum lighting does not come on The lighting switches off automatically to save energy Switch the dryer off and then on again The lamp needs changing Change the lamp a
20. dings numbered show the operating sequence and can be used as a brief guide to using your machine Sort the laundry To ensure an even drying result separate out the washed laundry and sort it according to the drying level required the type of fibre or weave Size the moisture content after spinning N Make sure that objects e g detergent dispensing balls have been removed from the laundry They could melt and cause damage to the dryer or the laundry Check seams and stitching to ensure that padding and linings are intact Fasten duvet covers and pillow cases to prevent small items from being trapped inside them Fasten hooks and eyes etc Tie fabric belts and apron strings Sew in or remove underwiring from bras Turn on the tumble dryer m Switch the dryer on by pressing the On Off button CD The tumble dryer may be switched on after loading saving energy as the light will not come on O Load the tumble dryer m Press the oa button to open the door m Load the laundry loosely into the drum Do not overload the drum See the Programme chart for recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result m Before closing the door make sure the fluff filter is correctly positioned in the door Check the laundry is right inside the drum so that it
21. drying when the dryer is next used If the appliance is switched on at the mains and the door is opened the drum lighting will come on It will go out a few minutes later to save energy m Press the D button to switch the dryer off m Clean the fluff filters m Close the door Favourite programmes You can programme the short cut buttons to callup the four drying programmes you use most frequently Selecting changing a favourite m Switch the dryer on Entry menu 1 Cottons 2 Minimum iron Settings F 3 Woollens handcare 4 Smoothing 9 00 m Press short cut button Main menu Cottons Duration 1 23 h Extras Timer Ih b d bd m Turn the multi function selector to highlight either the Programme or the Drying level m Confirm your selection of the part you want to change by pressing the multi function selector once Depending on the option highlighted the following will be displayed Programme selection Programme Back 4 selection Iinirium iran Delicates m Use the multi function selector to select the programme you want and confirm your selection The main menu will appear 18 Favourite programmes Important If you do not make a selection in the sub menu within approx 15 seconds the display will revert to the main menu Programmes with drying levels Cottons Marmal Drying level Machine iron Extra dry ET m Use the multi function selector to sel
22. ect the drying level you want and confirm your selection The display will show which drying levels can be selected for each individual programme Warm air Cool air programmes arm air Finish 3 30 Duration Warm air 0 30 h m Use the multi function selector to select the duration you want and confirm your selection 15 to 30 minutes in 5 minute stages 30 minutes to 2 hours in 10 minute stages The programme end time for the duration selected will also appear Other programmes You cannot alter the drying level or duration for the other programmes Favourite programmes Selecting an extra option m Press short cut button Extras Cottons Mormal Low temp Back m Use the multi function selector to select the extra option you want and confirm your selection The main menu will reappear Saving a favourite programme All the settings you have selected are now shown in the main menu Cottons Horrnalt Low temp Duration 1 59 h Extras Timer c Back bd v v m Press short cut button 9 Save Selecting a short cut button Cottons Marmal Low temp Previous Cottons Normal Save to Ee 4 Back 4 m Use the multi function selector to select the number you want and confirm your selection Your settings have now been saved as a favourite programme and will appear in the Entry menu Repeat the procedure if you want to customise other favourite programme
23. ecting an individual future programme quickly These buttons can be programmed to select your own favourite drying programmes This is used to select menu options Start button by turning it and to confirm your selection by pressing it On Off button D To switch the dryer on or off 2 Short cut buttons Multi function selector Door button o To open the door Operating the tumble dryer Display Entry menu 1 Cottons Programme selection 2 Minimum iron Settings F 3 Woollens handcare 4 Smoothing 9 00 When the machine is switched on the entry menu with factory default settings appears and Programme selection is highlighted Multi function selector Short cut buttons Turning the multi function selector moves the highlighting to the next menu option Pressing the multi function selector selects the highlighted menu option Pressing a short cut button selects one of the four favourite programmes which appear on the left of the display You can customise the favourite programmes to suit your own requirements The short cut buttons have different functions in the other menus Where this is the case an arrow W will appear in the display above the short cut button together with a description of its function Programme selection There are two ways of selecting a programme Option 1 Select the Programme selection menu in the display and confirm your selection by pressing
24. eed rue Osea oes lg E ee 53 Ko rr 53 eps L 55 Kopad TONG sanan te tn ay cece ee MER D DELETED 55 Display CONAS err a a ee ge nen 55 AIMCO en ere ee ae ae Dee gl 56 Warning and Safety instructions To avoid the risk of accidents and damage to the machine please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner of the machine Correct use The tumble dryer is only intended for drying fabrics which have been washed in a water solution marked on the manufacturer s care label as being suitable for tumble drying Dry cleaning kits for freshening up garments in a tumble dryer are increasingly available on the market If using do so at your own risk and follow the instructions provided on the packaging Any other applications may be dangerous The manufacturer is not liable for damage resulting from improper use or operation Technical safety Before setting up the machine check it for any externally visible damage Do not install or use a damaged machine Before connecting the machine ensure that the connection data on the data plate voltage and connected load match the mains electricity supply If in any doubt consult a qualified
25. hing machine Fabrics are not completely dried in this programme Remove garments as soon as the programme has finished and leave to finish drying at room temperature Extra option Low temperature Low temperature cannot be deselected Warm air Max load 6 kg Fabric type Voluminous and multi layered fabrics whose layers have different drying characteristics e g jackets pillows For drying individual items e g bath towels bathing costumes tea towels Notes Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Extra option Low temperature select this option for delicate fabrics with the O symbol on the care label Cool air Max load 6 kg Fabric type Any item which only needs airing Weight of dry laundry 25 Programme chart Sportswear Max load 2 kg Normal Normal Hand iron 4 Fabric type Sportswear which is suitable for drying in a tumble dryer Outerwear Max load 2 kg Normal Hand iron 4 Fabric type Outerwear which is suitable for drying in a tumble dryer Proofing Max load 2 kg Fabric type For drying microfibre fabrics ski wear fine closeweave cotton garments poplin or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish
26. hows you the setting The machine is delivered with a medium setting set as stan dard Depending on the setting the programme duration will be shorter Damper or longer Drier Extending the cooling down time 52 The cooling down phase which takes place before the end of a programme can be lengthened if required This makes the garments easier to handle The bar chart shows you the setting The machine is delivered with O mins normal cooling down period set as standard You can select an extended cooling down time in 2 minute increments up to a maximum of 18 minutes You cannot extend the cooling down time for the Warm air Cool air Woollens handcare or Smoothing programmes Settings menu F Airways indicator Fluff should be removed after drying The Clean the filters message will remind you to clean the filters when a certain amount of fluff has collected in them You can decide at what level of fluff this reminder should be given You will have an idea of how often this should be done after a few drying programmes Off Clean the filters does not appear Heavy Clean the filters only appears when there is a heavy build up of fluff Normal Factory default setting Light Clean the filters appears when there is only a small build up of fluff A tick will appear beside the option to show that it has been set Anti crease action Lock The drum will continue to rotate at interval
27. m Once clean push the filter back into the door holder until it clicks into position Ensure it is facing the correct way m Also clean the door seal 2 with a damp cloth m Use your fingers to remove the fluff from the two fluff filters in the door opening m Close the door Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters they can be removed and cleaned under hot running water m To remove the fluff filter from the door holder see previous page m To remove the filters in the door opening grip the holder and push upwards in the direction of the arrow to remove it m Rinse the filters under hot running water m Then shake the filters until no more water droplets are visible m Dry the filters thoroughly with care N Do not replace them if they are damp or wet Damp or wet filters could cause operational faults m Push the large filter back into the door holder until it clicks into position Ensure it is facing the correct way m Place the filters back in the door opening the left and right filters are identical with the finger holders facing upwards See illustration Cleaning the tumble dryer Disconnect the machine from the mains electricity supply m Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water m The drum and other stainless steel parts can be cleaned with a suit
28. mme Cottons Marmial Low temp m Use the multi function selector to select the programme end time and confirm your selection The programme end time will be adjusted to the next full or half hour Once the end time has been entered the start time of the programme will also appear To start the timer m Press the Start button The timer will count down in minutes until the start of the programme If the time until the programme start is more than one hour the drum will turn briefly every hour to prevent creasing While the timer is counting down you can still change the Extra options or drying levels press the oa button and add or remove laundry After shutting the door again press the Start button alter the programme end time by pressing short cut button Timer To cancel the timer m Press short cut button 4 once to cancel the timer Press it again to come out of this menu 22 Programme chart Cottons Max load 6 kg Extra dry Normal Normal Fabric type Single and multi layered cotton fabrics such as towelling jerseywear underwear flannelette bedlinen Notes Select Extra dry for multi layered and very thick fabrics Do not use Extra dry for jersey fabrics as they have a tendency to shrink Extra options Short Low temperature select this option for delicate fabrics with the E symbol on the care label Hand iron 4 Hand iron 447 Machi
29. moisture levels after spinning fluctuations in the electricity supply and any Extra options selected 47 Technical data Height Widih Depth Depth with door open Weight Drum volume Maximum capacity Capacity of condensed water container Hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Connected load Fuse rating UK Lamp wattage Energy consumption Test certificates awarded 48 850 mm adjustable 7 7 mm 595 mm 580 mm 1 060 mm 54 kg 100 litres 6 kg dry weight approx 3 5 2m 1m 3m 2m see data plate see data plate see plug see data plate see Consumption data section Radio TV suppression VDE Settings menu P for changing standard settings The Settings menu is used to alter the dryer s electronics to suit different requirements Settings can be altered at any time 49 Settings menu P To open the Settings menu 1 Cottons Programme selection 2 inirur iron Settings P 3 Woollens handcare 4 Smoothing 3 00 m Select Settings P from the entry menu and confirm your selection with the multi function selector To select a setting Back 4 Language P Time of day Drying lewels m Select the setting you want to change and confirm your selection If you do not make a selection in the sub menu within approx 15 seconds the display will revert to the main menu To close the Se
30. n the display m Holding the container firmly in both hands as shown pull it out slightly towards the right hand side m Hold the container in a horizontal position when carrying it m Open the shutter and empty out the water m To replace the container hold it at a slight angle as when removing it and push it in gently until you feel it click into position m To remove the message from the display switch the dryer off and then on again Condensed water should not be consumed It could lead to health problems for people and animals Condensed water can be put to household use e g used in a steam iron or humidifier To ensure that any residual particles of fluff in the condensed water are removed before use pass it through a fine sieve or paper filter first 29 Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening Clean the filters after each drying programme Cleaning them whilst dry m Open the door and pull the fluff filter 1 out ofthe door as illustrated m Use your fingers to remove the fluff from the surface of the filter 30 m Remove any fluff from the hollow part of the door holder A cleaning brush is available as an optional extra from your Miele dealer or the Miele Spare Parts Department Tip You can also use a vacuum cleaner
31. ne iron Fabric type Cottons or linen fabrics e g table bedlinen starched laundry Notes To prevent laundry from drying out it should be rolled up until you are ready for ironing Extra options Short Low temperature select this option for delicate fabrics with the E symbol on the care label Minimum iron Max load 3 kg Normal Normal Hand iron 4 Fabric type Minimum iron items made of cotton synthetic or blended fabrics e g shirts blouses skirts and table cloths Notes In the Minimum iron Hand iron programme items are dried with very little creasing depending on fabric type and amount of laundry Extra options Short Low temperature select this option for delicate fabrics with the E symbol on the care label A Weight of dry laundry vote for test institutes Use this programme without any extra options when testing according to EN 61121 Standard 23 Programme chart Delicates Max load 2 kg Normal Normal Hand iron 4 Hand iron 44 Machine iron Fabric type For delicate garments made of synthetic fibres mixed fibres easy care cotton shirts and blouses and evening wear with sequins and beading Extra option Low temperature Low temperature cannot be deselected Automatic Max load 3 kg Normal Normal Hand iron 4 Fabric type Mixed load of cotton and minimum iron f
32. ogramme is recognised that there to dry individual items cancelled was no laundry in the To delete the fault the buzzer sounds drumand cancelled the message programme Open the door or switch Drying individual the dryer off and then garments or items which back on again are already dry can also cause the programme to be cancelled iz The condensed water Empty out the condensed Empty out the container container is full or there is water container or check the programme is a kink in the drain hose the drain hose cancelled To delete the fault message Switch the dryer off and then back on again the buzzer sounds 35 Problem solving guide Problem Possible cause Remedy The following message appears after the programme has finished Clean the filters The dryer is not working efficiently or economically Possible cause The filter is clogged with fluff or with detergent residues Cleaning the filters is usually all that is required However if the message does not go out after you have cleaned the filters then also check all the possible causes described under The drying process goes on too long or even switches off To delete the fault message Switch the dryer off and then back on again You can adjust the setting which controls when or if the message Clean the filters appears See Settings menu Airways indicator
33. rain hose 45 Electrical connection Electrical connection U K All electrical work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations Ensure power is not supplied to the appliance until after installation work has been carried out The appliance is supplied with a mains cable with moulded plug ready for connection to a 230 240V mains supply The voltage and connected load are given on the data plate Please ensure these match the household mains supply The fuse rating is quoted on the plug Connection should be made via a suitable switched socket which is easily accessible after installation For extra safety it is advisable to install a residual current device RCD with a trip Current of 30 mA in accordance with DIN VDE 0664 VDE 0100 Section 739 Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating 46 Non rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse and if the fuse cover is lost the plug must not be used until a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words on the base of the plug as applicable to the design of plug fitted Replacement fuses should be ASTA approved
34. room temperature fluctuations in power supply The electronics continually assess conditions in the machine and adjust the estimated time remaining for a more accurate reading Because of this the time displayed can alter during the course of a programme In the same way the Woollens handcare and Smoothing programmes can finish earlier than expected if a certain temperature is reached This can happen with particularly fine fabrics or if items were dry beforehand How to dry correctly Before the end of a programme m Empty the condensed water container unless the dryer is There see CODING COW DNase SENI connected for external drainage end of the drying sequence Cooling down will appear in the display The programme will not finish until the cooling down phase has been completed There is no cooling down phase at the end of the following programmes Woollens handcare Smoothing At the end of a programme Anti crease and Finish will appear in the display to indicate that the programme has finished The buzzer will sound During the anti crease phase factory default setting the drum will continue to rotate at intervals to prevent laundry creasing if you do not wish to remove it immediately The anti crease phase lasts for 1 hour Remove the laundry m Press the oa button to open the door m Remove the laundry Make sure that the drum is empty If items are left in the dryer they could be damaged by over
35. s eese rem pede E Rc pex dd Ohad bar UAE be quos 37 Changing thelamp as seu epa pre en dr Bere a enge 40 After Sales service illl ese 41 Future updates PO cuu be ADHERE dh DER ax Deua be oe d ded dd 41 Appliance guarantee 1 rs 41 Optional accessorles nia x ect eR PEG ae CARRIER E OR ROSE UR E Rep 41 Installation RH RH 42 FONE VIG deiig tee ee Bee ea en eu ke ee nur 42 Installal n siie a sasaji kar ob rear 43 Room in which the dryer is located aa 43 Transporting the machine to its installation site 43 Aligning the machine 2 22 seeeeeeen rennen een 43 Before moving the machine again e g when moving house 43 External condensed water outlet 2 aK Ka eee 44 Setting up the drainhose 2 22 eee 44 Connection to a sink drain outlet 0 aaa 45 If you no longer wish to use an external condensed water outlet 45 Contents Electrical connection GG 46 ElectriGal connectiom UI uus ses nsa be aa E RUE A 46 Consumption ees 47 Technical data GG 48 Settings menu RR 50 Language ee a Cere eran EE CE ee ee eon ad 50 GO GAN ss sate ag A Bak WERNE T IEEE LETTRE 51 Drying levels 2 aa ai eee eee 52 Extending the cooling down time lile 52 Airways IndiGator 4 essersi e cbr RR ey ev ae 53 Anti Crease agllon isses bet opa
36. s and save them to short cut buttons which have not yet been used 20 Extra options Selecting an extra option Short Not all the extra options are suitable for use with every programme It is not possible to select the Short and Low temperature options at the same time m Use the multi function selector to select the Extra you want and confirm your selection An extra option which has already been selected is indicated by a tick V can be de selected by highlighting it and then confirming your selection For drying fabrics which can withstand higher temperatures Do not use on minimum iron or delicate fabrics The programme duration is shorter Low temperature Delicate fabrics are dried at a lower temperature For all delicate or minimum iron fabrics with the C symbol on the care label e g acrylic garments The programme duration is longer On some programmes Low temperature is a standard part of the programme and so cannot be deselected 21 Timer You can use the timer to set the end time of a programme allowing you to make use of night time economy electricity rates for example The start of a programme can be delayed by up to 24 hours To open the Timer sub menu Cottons Marmal Low temp Duration 1 59 h Extra options Timer T Back v v v m Press short cut button 2 Timer This opens the Timer sub menu To select the end time of a progra
37. s described at the end of this section The display is in a different language A different language has been selected in the Settings Language IN menu Set the language you want The flag symbol will guide you The Start button light flashes when a programme is being selected This is not a fault The flashing indicates that a programme can be started After the programme has started the flashing will change to a constant light The display is dark and the light ring around the multi function selector is not lit up The Start button is flashing slowly The display has switched off automatically to save energy Standby mode The display and the multi function selector will light up when one of the buttons is pressed The lighting is defective if it does not come on when one of the buttons is pressed Contact the Miele Service Department 39 Problem solving guide Changing the lamp Thelamp specification and Disconnect the machine from the maximum wattage is stated on the mains electricity supply data plate and on the lamp cover m Open the door m Replace the lamp You will find the interior lamp cover at m lo close the cover push it upwards the top of the drum aperture and press it on the left and right until you hear it click into position N Ensure that it is fitted into position securely as any moisture could cause a short circuit m in
38. s for one hour to prevent laundry creasing if you do not wish to remove it immediately A tick will appear beside the option to show that it has been set The machine is delivered with the option On set as standard The anti crease function cannot be used with the Woollens handcare programme The system lock prevents your machine being used without your knowledge When the system lock has been activated you have to enter a code after switching the dryer on Otherwise the dryer cannot be operated The door is not locked and can be opened at any time To activate the lock m Select Activate and confirm your selection 53 Settings menu P To enter the code The display will now request that a code is entered The code is 250 and cannot be altered Enter lock code m Turn the multi function selector until the number 2 appears Confirm your selection of this number Now set the second number m Repeat the process until all three numbers have been entered After the last number has been entered you must confirm the code with OK 2 5 Confirm lock cade m Confirm the code then switch the dryer off To unlock the machine When the machine is switched on again the display will request the lock code m Enter lock code 250 as described above and confirm the entry To deactivate the lock 54 m Proceed as for activating the lock Settings menu F Buzzer Keypad tones
39. sert a suitable tool such as a wide bladed screwdriver under the side edge of the lamp cover as illustrated m Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover The cover will open downwards The temperature resistant lamp should only be ordered from your Miele dealer or the Miele Spare Parts Department 40 After Sales service In the event of any faults which you cannot remedy yourself or ifthe machine is under guarantee please contact your Miele dealer or the Miele Service Department see back cover for contact details When contacting your dealer or the Service Department please quote the model and serial number of your machine both of which are shown on the data plate situated on the right hand side below the drum aperture Future updates PC The indicator or check light marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the machine s programme data Appliance guarantee Please see the guarantee card supplied with your machine Optional accessories Optional accessories for this dryer are available from your Miele Dealer or from the Miele Spare Parts Department Please note that telephone calls may be monitored and recorded for training purposes 41 Installation Front view Mains connection cable 2
40. sit or lean on the door as this can cause the machine to tip up Always close the door after use This way you will avoid the danger of children climbing onto or into the dryer or hiding things in it pets or other small animals climbing into it Safety with children This machine is not a toy To avoid the risk of injury keep children away from the machine at all times and supervise them whilst you are using it Do not allow children to play on or near it or to play with its controls Supervise its use by the elderly or infirm Using accessories Accessory parts may only be fitted when expressly approved by Miele If non Miele parts are used with this machine guarantee performance and product liability claims may be invalidated Disposal of your old machine Before discarding an old machine switch it off at the wall socket and unplug it Render the plug useless and cut off the cable directly behind the machine This should be done by a competent person The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the tumble dryer Control panel CD SB s o eo 6 bo 6 ae Display Optical interface PC See the following pages for more This is used by service technicians information to run diagnostic checks on your machine and can also be used to update programming data in the For sel
41. tend to become matted and shrink if dried in a tumble dryer They can however be partially dried using the Woollens handcare programme 14 Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise become rough They can be partially dried using the Smoothing programme Loopknit garments e g T shirts and underwear tend to shrink depending on their quality Do not over dry these textiles When purchasing these garments it is advisable to take their shrinkage properties into account For garments made from very fine weave fabrics such as shirts or blouses only use the Shirts or Delicates programme to avoid creasing If in doubt reduce the load or use the Smoothing or Silks handcare programme Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch should be used New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the machine Dark coloured fibres can also settle on light coloured garments and vice versa How to dry correctly Brief instructions The hea
42. that your laundry is thoroughly spun at the washing machine s maximum spin speed The tumble dryer has been overloaded Do not exceed the maximum load for the programme selected Metallic components e g zips have prevented the dryer from registering the correct moisture level in the laundry Open zips next time If the problem occurs again dry garments with long zips using the Warm air programme timed drying Detergent residues hair and fine fibres can block up the condenser unit Check the condenser unit from time to time and clean it if necessary The vents below the door are blocked Remove any objects that are blocking the vents The laundry is not sufficiently dry The load consisted of different fabrics Finish drying using the Warm air programme Select a different programme the next time 37 Problem solving guide Problem Possible cause Remedy The condenser unit service panel will not shut Water leaks from the machine after the condenser unit has been cleaned The inner cover of the condenser unit has not been locked properly and or the condenser unit has not been positioned correctly Fluff has collected at the bottom ofthe condenser unit housing Ensure that the condenser unit is positioned correctly and lock the cover Check the rubber seals Use a cloth to remove any fluff from the insi
43. the multi function selector Option 2 Press short cut button or This will automatically take you into the main menu of that programme Operating the tumble dryer Programme selection menu Programme Back 4 selection Iinirnum iran Delicates You can use the multi function selector to select any programme The highlighting will move up or down depending on the direction the multi function selector is turned in The A W arrows on the right of the display indicate the direction and further options Pressing the multi function selector takes you to the main menu of the programme selected Drying programme main menu Cottons Marrnal Duration 1 23 h Extras Timer J Back v v v m Turn the multi function selector to highlight either the Drying level or the Programme m Pressing the multi function selector selects the highlighted option and opens the relevant sub menu m The sub menus Extras Timer and Save can be opened by pressing the short cut button directly below them You return to the entry menu by pressing short cut button below the word Back Alternatively you can also highlight and confirm all options by just using the multi function selector Important All the times given in these instructions are examples and can vary Settings menu The Settings menu is used to alter the tumble dryer s electronics to suit different requirements See Settings menu for more details
44. the cover after cleaning ensure that the rubber seal fits correctly into the groove m Replace the cover making sure the hooks locate correctly Hold it at an angle and push it gently downwards m Then turn the lever upwards into the horizontal position to lock the cover m Replace the service panel and press the upper edge until it clicks into position Itis important to ensure that both the condenser unit and the cover are correctly positioned and locked otherwise water may leak from the machine Problem solving guide Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department N Repair work to electrical appliances should only be carried out by a suitably qualified person in accordance with local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Fault messages in the display Problem Possible cause Remedy Machine locked Enter The lock has been See Settings menu P lack code activated a The electronic Press and hold the Start System locked programme lock has button until Ready appears been activated in the display This is not a fault Use the Warm air Adjust the load The electronic unit programme timed drying the pr
45. to BS 1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier WARNING THIS APPLIANCE MUST BE EARTHED Consumption Programme Load Final spin speed Energy Time in a domestic washing machine kg rpm kWh Minutes Cottons 6 0 800 70 residual moisture 3 90 109 Normal 1200 3 10 87 1400 2 95 83 1600 2 80 81 1800 2 55 74 Cottons 6 0 800 70 residual moisture 3 25 93 Hand iron 44 1200 2 40 71 1400 2 25 66 1600 2 15 64 1800 1 85 56 Minimum iron Normal 3 0 1000 50 residual moisture 1 50 47 Minimum iron Hand iron 4 3 0 1000 1 30 41 Delicates Normal 2 0 1 25 78 Automatic Normal 3 0 900 1 85 66 Shirts Normal 2 0 900 1 25 48 Denim Normal 3 0 800 1 75 52 Woollens handcare 2 0 900 0 15 Silks handcare 1 0 0 15 Smoothing 3 0 0 30 Sportswear Normal 2 0 1 40 50 Outerwear Normal 2 0 1 50 57 Proofing 2 0 1 60 56 Pillows 1 0 1 60 84 Large Pillows 1 2 1 60 98 Weight of dry laundry EN 61121 test programme All data established in accordance with EN 61121 Before testing in accordance with EN 61121 dry a 3 kg load of cotton laundry with 7096 residual moisture as per the above standard using the Cottons Normal programme without any Extra options Consumption data can vary from the nominal values given above depending on the size of the load types of textiles residual
46. ttings menu Language PR Time of day Drying levels m Select Back and confirm your selection The display will revert to the entry menu Language F The display can be set to appear in several different languages A tick will appear beside the language to show that it has been set The flag P after the word Language acts as a guide to prevent a language which will not be understood from being set 50 Settings menu F First select either a 24 hour or 12 hour clock Then set the current time of day To select a 24 hour or 12 hour clock Time of day m Select either the 24 hour or the 12 hour clock option and confirm your selection The display will then change to the screen for setting the time of day To set the time of day 10 Be Please set the time of day m Use the multi function selector to select the hour and confirm your selection Now set the minutes Confirm the selection again to save the time of day in memory The time of day can be changed at any time later on by 1 Cottons Programme selection 2 Minimum iron Settings F 3 Woollens handcare 4 Smoothing C m Highlighting the time of day in the Entry menu and confirming your selection The display will then change to the screen for setting the time of day 51 Settings menu Drying levels You can alter the drying levels for the Cottons and Minimum iron programmes The bar chart s
47. ubject to infestation by cockroaches or other vermin pay particular attention to keeping the machine and its surroundings ina clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the machine guarantee Warning and Safety instructions In the event of a fault or for cleaning purposes the machine is only completely isolated from the electiricty supply when itis switched off at the wall socket and the plug is withdrawn or itis switched off at the mains or the mains fuse is withdrawn Operation This equipment may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way The fluff filters must be thoroughly dried after cleaning If they are still damp or wet when replaced there is a risk of faults occurring when the machine is used The dryer must not be used without the condenser unit in place Do not install the machine in a room where there is a risk of frost occurring At temperatures around freezing point the machine may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump hoses and or condensed water container The ambient room temperature shoul
48. ving house After each use a small quantity of condensed water will collect in the area around the pump This water can run out if the machine is tipped up when it is being moved It is a good idea to run the Cool air programme for approximately 1 minute before moving the machine Any remaining condensed water will then be fed into the condensed water container or out through the drain hose 43 Installation External condensed water outlet When drying is in progress condensed water is pumped into the condensed water container through the drain hose atthe back of the dryer The condensed water can also be drained off directly if the machine is installed near a sink drain outlet etc so that the condensed water container does not have to be emptied The drain hose approx 2 m long is stored in the dryer It must be pulled out of the dryer to its full extent if condensed water is to be drained externally Maximum delivery head 1m If it is not long enough an extension hose is available as an optional accessory through your dealer or from the Miele Spare Parts Dept Setting up the drain hose From the back of the dryer at the top m Unclip the drain hose from clip 1 m Then pull it off holder 2 44 From the back of the dryer at the bottom AN e 2 D m Unclip the drain hose from clip 3 m Then pull the drain hose completely out of the dryer towards the left 4 See illustration
Download Pdf Manuals
Related Search