Samsung SyncMaster 963UW User manual
Contents
1. Connections Tilt angle Using You can adjust the tilt angle within a range of 3 forward to 24 backward for the most comfortable viewing angle Attaching a Base This monitor accepts a 75 mm x 75 mm VESA compliant mounting interface pad Q Monitor Mounting interface pad Sold separately 1 Turn off your monitor and unplug its power cord 2 Lay the LCD monitor face down on a flat surface with a cushion beneath it to protect the screen 3 Remove four screws and then remove the stand from the LCD monitor 4 Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm type base wall mount hanger or other base A e Do not use screws longer than the standard dimension as they may damage the inside of the Monitor Downloaded from ManualMonitor com Manuals Connections e For wall mounts that do not comply with VESA standard screw specifications the length of the screws may differ depending on their specifications Do not use screws that do not comply with the VESA standard screw specifica tions Do not fasten the screws too tightly as this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents e Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the p2. Downloaded from ManualMonitor com Manuals Introduction Package Contents Note Please make sure the following items are included with your monitor If any items are missing contact your dealer Contact a local dealer to buy optional items Unpacking Without stand With stand Monitor Monitor Manuals Quick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables cr Se D Sub Cable Power Cord USB Cable Sold separately DS FF AY DVI Cable HDMI Cable Headphones Downloaded from ManualMonitor com Manuals Introduction Others Cleaning Cloth h Note This is only provided for highly polished black products as a product feature Your Monitor Initial Settings The optimal resolution for this monitor is as follows eee gt 4 een HZ Follow the above settings to set the resolution Language Select the language using the up or down key The displayed content will disappear after 40 seconds Turn the Power button off and on It will be displayed again It can be displayed up to three 3 times Make sure to adjust the resolution of your PC before reaching the maximum count Note The resolution displayed on the screen is the optimal resolution for this product Adjust your PC resolution so that it is the same as the optimal resolution for this product Downloaded from ManualMonitor com Manuals Introduction Front 1 MENU button MENUAL
3. Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Downloaded from ManualMonitor com Manuals Troubleshooting Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode y seee sehiz Environment The location and the position of the monitor may influence the quality and other features of the monitor If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Useful Tips A monitor recreates visual signals received from the computer Therefore if the
4. an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog Press SOURCE button to have the monitor double check the input signal source Q Ifthe power is on reboot the computer to see the initial screen the login screen which can be seen A Ifthe initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your deal er Can you see Not Optimum Mode Recommended Mode 1440 x 900 60 Hz on the screen You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly A Adjust the maximum resolution and frequency that the monitor can handle properly A Ifthe display exceeds WSXGA or 75 Hz a Not Optimum Mode Recommended Mode 1440 x 900 60 Hz message is displayed If the display exceeds 85 Hz the display will work properly but the Not Optimum Mode Recommended Mode 1440 x 900 60 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The message is displayed again if the system is rebooted Q There is no image on the screen Is the power indicator on the monitor blinking at 1
5. second intervals Downloaded from ManualMonitor com Manuals Troubleshooting The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the SOURCE 2 button Then press any key on the keyboard again to activate the monitor and restore the image on the screen Connected using the DVI cable You may get a blank screen if you boot the system before you connect the DVI cable or dis connect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system cannot see the On Screen Display Q A Have you locked the On Screen Display OSD Menu to prevent changes Unlock the OSD by pressing the MENU I button for at least 5 seconds The screen shows strange colors or just black and white Q A A Q A Is the screen displaying only one color as if looking at the screen through a cellophane paper Check the signal cable connection Make sure the video card is fully inserted in its slot Have the screen colors become strange after running a program or due to a crash between ap plications Reboot the computer Has the video card been set properly Set the video card by referring to the video card manual The screen suddenly has become unbalanced Q A Q A Have you changed the video c
6. video for video chatting O Mic Using this microphone you can view and send audio for video chatting Speaker You can hear sound by connecting the soundcard of your PC to the monitor Rear Note The configuration at the back of the monitor may vary from product to product POWER Downloaded from ManualMonitor com Manuals Introduction POWER Connect the power cord for your monitor to the POWER port on the back of the monitor DVIIN RGB IN Q VI IN Connect the DVI cable to the DVI IN port on the back of your monitor Ores IN Connect the RGB JN terminal at the back of your monitor to your computer O lt USB connection termi nal Option Dup USB upstream port Connect the a UP port of the monitor and the USB port of the computer with the USB cable Obown USB downstream port Connect the a DOWN port of the USB monitor and a USB device with the USB cable Note Touse lt DOWN Downstream Port you have to connect the gt UP Upstream Cable to the PC Make sure to use the USB cable supplied with this monitor to connect the monitor s lt UP port and your computer s USB port Downloaded from ManualMonitor com Manuals Introduction 2 E Kensington Lock The Kensington Lock is a device used to physi cally fix the system when using it in a public place The locking device has to be purchased separately The appearance and locking meth
7. Check note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test Feature Check 1 Turn off both your computer and the monitor 2 Unplug the video cable from the back of the computer 3 Turn on the monitor If the monitor is functioning properly you will see a box in the illustration below Check Signal Cable This box appears during normal operation if the video cable becomes disconnected or damaged 4 Turn off your monitor and reconnect the video cable then turn on both your computer and the monitor If your monitor screen remains blank after using the previous procedure check your video controller and computer system your monitor is functioning properly Warning Messages If there is something wrong with the input signal a message appears on the screen or the screen goes blank although the power indicator LED is still on The message may indicate that the monitor is out of scan range or that you need to check the signal cable Not Optimum Mode Recommended Mode x seee sehiz Environment The location and the position of the monitor may influence the quality and other features of the monitor If there are any sub woofer speakers near the monitor unplug and relocate the woofer to another room Remove all electronic devices such as radios fans clocks and telephones that are within 3 feet one meter of the monitor Downloaded from Ma
8. Examples of media devices MP3 digital camera etc Downloaded from ManualMonitor com Manuals Connections e You can run move copy or delete the files on the storage device Examples of storage devices external memory memory card memory reader HDD type MP3 player etc e You can use other USB devices that can be connected to a computer Note When connecting a device to the DOWN port of the monitor connect the device using a cable appropriate to the device For the purchase of the cable and external devices ask the service center of the corresponding product The company is not liable for problems or damages to an external device caused by using an unauthorized cable for the connection Some products do not follow the USB standard and it may cause a malfunction of the device If the device malfunctions even if it is connected to the computer contact the service center of the device computer 963UW Connecting Headphone Note You may connect your headphones to the monitor 1 Connect your headphones to the Headphone connection terminal 963UW Connecting MIC note You may connect your microphone to the monitor Downloaded from ManualMonitor com Manuals Connections 1 Connect the microphone cable to the MIC port on the monitor 963UW Using the Stand Monitor Assembly Simple Stand Monitor and Bottom Downloaded from ManualMonitor com Manuals
9. Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu Customized Key You can customize key assignment for the Custom button according to your pref erences Note You can configure the Customized key for a required function via Setup gt Cus tomized Key 3 Volume button When OSD is not on the screen push the button to adjust volume gt gt Click here to see an animation clip Adjust buttons Wf Adjust items in the menu O SOURCE button Enter button Push the SOURCE then selects the video signal while the OSD is off When the SOURCE button is pressed to change the input mode a message appears in the upper left of the screen displaying the current mode analog or digital input signal Activates a highlighted menu item Downloaded from ManualMonitor com Manuals Introduction Note If you select the digital mode you must connect your monitor to the graphic card s DVI port using the DVI cable gt gt Click here to see an animation clip 6 AUTO button Use this button for auto adjustment Available in Analog mode only gt gt Click here to see an animation clip QO Power button Power indicator Use this button for turning the monitor on and off This light glows blue during normal operation and blinking blue once as the monitor saves your adjustments Q Camera Using this camera you can view and send
10. alled remove it reboot the computer and then install the program again You need to reboot the computer for it to operate normally after installing or removing the program Note Visit the MagicTune website and download the installation software for MagicTune MAC Check the following items if there is trouble with the monitor Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does request an a service for the main board of the computer If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter in the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver Note If problems repeatedly occur contact an authorized service center 2063UW Q amp A Q How can I change the frequency The frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Q How can I adjusts the resolution W
11. ard or the driver Adjust screen image position and size using the OSD Have you adjusted the resolution or frequency to the monitor Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD The screen is out of focus or OSD cannot be adjusted Q A Have you adjusted the resolution or frequency on the monitor Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes Downloaded from ManualMonitor com Manuals Troubleshooting LED is blinking but no images on the screen Q Is the frequency properly adjusted when checking the Display Timing on the menu A Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product There are only 16 colors shown on the screen The screen colors have changed after changing the video card Q Have the Windows colors been set properly A Windows XP Set the resolution at the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution at the Control Panel Display Settings Q Has the video card been set properly Set the video card by referring to the video card manual There is a message that reads Unrecognized monitor Plug amp Pl
12. ask the service center of the corresponding product The company is not liable for problems or damages to an external device caused by using an unauthorized cable for the connection Some products do not follow the USB standard and it may cause a malfunction of the device If the device malfunctions even if it is connected to the computer contact the service center of the device computer 2063UW Connecting Headphone Note You may connect your headphones to the monitor Downloaded from ManualMonitor com Manuals Connections oll 1 Connect your headphones to the Headphone connection terminal 2063UW Connecting MIC note You may connect your microphone to the monitor lal 1 Connect the microphone cable to the MIC port on the monitor Downloaded from ManualMonitor com Manuals Connections 2063UW Using the Stand Monitor Assembly Simple Stand Monitor and Bottom Tilt angle Using You can adjust the tilt angle within a range of 3 forward to 24 backward for the most comfortable viewing angle Attaching a Base This monitor accepts a 100 mm x 100 mm VESA compliant mounting interface pad Downloaded from ManualMonitor com Manuals Connections Q Monitor Mounting interface pad Sold separately 1 2 Turn off your monitor and unplug its power cord Lay the LCD monitor face down on a flat surface with a cushion beneath it to protect the
13. ay VESA DDC monitor found Q Have you installed the monitor driver A Install the monitor driver according to the Driver Installation Instructions Q See the video card manual to see if the Plug amp Play VESA DDC function can be supported A Install the monitor driver according to the Driver Installation Instructions Check when MagicTune does not function properly Q MagicTune feature is found only on PC VGA with Window OS that supports Plug and Play A To check whether your PC is available for MagicTune feature follow the steps below When Windows is XP Control Panel Performance and Maintenance gt System Hardware Device Manager Monitors After deleting Plug and Play monitor find Plug and Play monitor by searching new Hardware A MagicTune is an additional software for the monitor Some graphic cards may not support your monitor When you have a problem with the graphic card visit our website to check the compatible graphic card list provided http www samsung com monitor magictune MagicTune doesn t work properly Q Have you changed your PC or video graphic card A Download the latest program The program can be downloaded http www samsung com mon itor magictune Downloaded from ManualMonitor com Manuals Troubleshooting Q Did you install the program Reboot the computer after installing the program for the first time If a copy of the program is already inst
14. become unbalanced Q A Q Have you changed the video card or the driver Adjust screen image position and size using the OSD Have you adjusted the resolution or frequency to the monitor Downloaded from ManualMonitor com Manuals Troubleshooting A Adjust the resolution and frequency at the video card Refer to the Preset Timing Modes Q The screen can be unbalanced due to the cycle of the video card signals Readjust Position by referring to the OSD The screen is out of focus or OSD cannot be adjusted Q Have you adjusted the resolution or frequency on the monitor A Adjust the resolution and frequency of the video card Refer to the Preset Timing Modes LED is blinking but no images on the screen Q Is the frequency properly adjusted when checking the Display Timing on the menu A Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes The maximum frequency per resolution may differ from product to product There are only 16 colors shown on the screen The screen colors have changed after changing the video card Q Have the Windows colors been set properly A Windows XP Set the resolution at the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution at the Control Panel Display Settings Has the video card been set properly A Set the video card by referring to the video card manual Ther
15. e is a message that reads Unrecognized monitor Plug amp Play VESA DDC monitor found Q Have you installed the monitor driver A Install the monitor driver according to the Driver Installation Instructions Q See the video card manual to see if the Plug amp Play VESA DDC function can be supported A Install the monitor driver according to the Driver Installation Instructions Check when MagicTune does not function properly Q MagicTune feature is found only on PC VGA with Window OS that supports Plug and Play A To check whether your PC is available for MagicTune feature follow the steps below When Windows is XP Downloaded from ManualMonitor com Manuals Troubleshooting Control Panel Performance and Maintenance System Hardware Device Manager Monitors After deleting Plug and Play monitor find Plug and Play monitor by searching new Hardware A MagicTune is an additional software for the monitor Some graphic cards may not support your monitor When you have a problem with the graphic card visit our website to check the compatible graphic card list provided http www samsung com monitor magictune MagicTune doesn t work properly Q Have you changed your PC or video graphic card A Download the latest program The program can be downloaded http www samsung com mon itor magictune Q Did you install the program Reboot the computer after installing the program
16. for the first time If a copy of the program is already installed remove it reboot the computer and then install the program again You need to reboot the computer for it to operate normally after installing or removing the program r Note Visit the MagicTune website and download the installation software for MagicTune MAC Check the following items if there is trouble with the monitor Check if the power cord and the video cables are properly connected to the computer Check if the computer beeps more than 3 times when booting If it does request an a service for the main board of the computer If you installed a new video card or if you assembled the PC check if the installed the adapter video driver and the monitor driver Check if the scanning ratio of the video screen is set to between 56 Hz 75 Hz Do not exceed 75 Hz when using the maximum resolution If you have problems in installing the adapter video driver boot the computer in Safe Mode remove the Display Adapter in the Control Panel System Device Administrator and then reboot the computer to reinstall the adapter video driver Note If problems repeatedly occur contact an authorized service center 963UW Q amp A Q How can I change the frequency The frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card ma
17. indows XP Set the resolution in the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can I set the Power Saving function Windows XP Set the resolution in the Control Panel Appearance and Themes Display Screen Saver Downloaded from ManualMonitor com Manuals Troubleshooting Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual A Windows ME 2000 Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual Q How can I clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer Downloaded from ManualMonitor com Manuals
18. m to the lt DOWN port of the monitor without connecting them to the PC The o USB port of the monitor supports High Speed Certified USB 2 0 High speed Full speed Low speed Data Rate 480 Mbps 12 Mbps 1 5 Mbps Power Consumption 2 5 W 2 5 W 2 5 W Max each port Max each port Max each port SAMSUNG 1 Connect the S UP port of the monitor and the USB port of the computer with the USB cable Note To use S DOWN port you have to connect the UP Upstream Cable to the PC Make sure to use the USB cable supplied with this monitor to connect the monitor s lt UP port and your computer s USB port Downloaded from ManualMonitor com Manuals Connections 2 Connect the R gt DOWN port of the USB monitor and a USB device with the USB cable 3 The use procedures are as the same as those for using an external device connecting to the PC e You can connect and use a keyboard and mouse e You can play a file from a media device Examples of media devices MP3 digital camera etc e You can run move copy or delete the files on the storage device Examples of storage devices external memory memory card memory reader HDD type MP3 player etc e You can use other USB devices that can be connected to a computer Note When connecting a device to the lt DOWN port of the monitor connect the device using a cable appropriate to the device For the purchase of the cable and external devices
19. nual for details Downloaded from ManualMonitor com Manuals Troubleshooting How can I adjusts the resolution Windows XP Set the resolution in the Control Panel Appearance and Themes Display Settings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can I set the Power Saving function Windows XP Set the resolution in the Control Panel Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual A Windows ME 2000 Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual How can I clean the outer case LCD Panel Disconnect the power cord and then clean the monitor with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the monitor Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer 2063UW Self Test Feature Check note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly Self Test
20. nualMonitor com Manuals Troubleshooting Useful Tips A monitor recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1440 x 900 60 Hz message comes up disconnect the cable from the computer while the monitor is still powered on If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble 963UW Check List r4 Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer No images on the screen cannot turn on the monitor Q Is the power cord connected properly A Check the power cord connection and supply Q Can you see Check Signal Cable on the screen A Connected using the D sub cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check
21. od may differ from the illustration depending on the manufacturer Refer to the manual provided with the Kensington Lock for proper use The locking device has to be purchased separately Note The location of the Kensington Lock may be dif ferent depending on its model Using the Anti Theft Kensington Lock 0 1 Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction 2 Connect the Kensington Lock cable 3 Fix the Kensington Lock to a desk or a heavy stationary object Or Headphone output terminal Ou Connect a microphone to the MIC terminal Cable holding ring Fix the cables using the holding ring as shown in the figure Downloaded from ManualMonitor com Manuals Introduction Note See 963UW Connecting Cables for further information regarding cable connections Downloaded from ManualMonitor com Manuals Connections 963UW Connecting Cables Rear of Monitor Rear of Computer Macintosh SAMSUNG Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet Use a connection appropriate for your computer Using the D sub Analog connector on the video card e Connect the signal cable to the 15 pin D sub port on the back of your monitor RGB IN Using the DVI Digital connect
22. or on the video card e Connect the DVI Cable to the DVI IN Port on the back of your Monitor a pa DVI IN 2 3 Connected to a Macintosh e Connect the monitor to the Macintosh computer using the D sub connection cable Note If the monitor and the computer are connected you can turn them on and use them Downloaded from ManualMonitor com Manuals Connections 963UW Connecting USB note You can use a USB device such as a mouse keyboard Memory Stick or external hard disk drive by connecting them to the lt DOWN port of the monitor without connecting them to the PC The USB port of the monitor supports High Speed Certified USB 2 0 High speed Full speed Low speed Data Rate 480 Mbps 12 Mbps 1 5 Mbps Power Consumption 2 5 W 2 5 W 2 5 W Max each port Max each port Max each port SAMSUNG 1 Connect the lt UP port of the monitor and the USB port of the computer with the USB cable U Note To use lt DOWN port you have to connect the UP Upstream Cable to the PC Make sure to use the USB cable supplied with this monitor to connect the monitor s lt UP port and your computer s USB port a E 2 Connect the gt DOWN port of the USB monitor and a USB device with the USB cable 3 The use procedures are as the same as those for using an external device connecting to the PC e You can connect and use a keyboard and mouse e You can play a file from a media device
23. re is a problem with the computer or the video card this can cause the monitor to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact the Service Center or your dealer Judging the monitor s working condition If there is no image on the screen or a Not Optimum Mode Recommended Mode 1680 x 1050 60 Hz message comes up disconnect the cable from the computer while the monitor is still powered on If there is a message coming up on the screen or if the screen goes white this means the monitor is in working condition In this case check the computer for trouble Downloaded from ManualMonitor com Manuals Troubleshooting 2063UW Check List 4 Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer No images on the screen cannot turn on the monitor Is the power cord connected properly A Check the power cord connection and supply Q Can you see Check Signal Cable on the screen A Connected using the D sub cable Check the signal cable connection Connected using the DVI cable If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog If you still see
24. roduct installation instructions A e To mount the monitor on a wall you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface e Contact the nearest Samsung Service Center for more information Samsung Electronics will not be responsible for damages caused by using a base other than those specified e Please use Wall Mount according to the International standards 2063UW Connecting Cables Rear of Monitor Rear of Computer Macintosh SAMSUNG ie a Connect the power cord for your monitor to the power port on the back of the monitor Plug the power cord for the monitor into a nearby outlet Use a connection appropriate for your computer Using the D sub Analog connector on the video card e Connect the signal cable to the 15 pin D sub port on the back of your monitor R Using the DVI Digital connector on the video card Downloaded from ManualMonitor com Manuals Connections e Connect the DVI Cable to the DVI IN Port on the back of your Monitor a cae DVI IN 2 3 Connected to a Macintosh e Connect the monitor to the Macintosh computer using the D sub connection cable Note If the monitor and the computer are connected you can turn them on and use them 2063UW Connecting USB note You can use a USB device such as a mouse keyboard Memory Stick or external hard disk drive by connecting the
25. screen Remove four screws and then remove the stand from the LCD monitor Align the mounting interface pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm type base wall mount hanger or other base A e Do not use screws longer than the standard dimension as they may damage the inside of the Monitor e For wall mounts that do not comply with VESA standard screw specifications the length of the screws may differ depending on their specifications Do not use screws that do not comply with the VESA standard screw specifica tions Do not fasten the screws too tightly as this may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents e Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions A To mount the monitor on a wall you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface e Contact the nearest Samsung Service Center for more information Samsung Electronics will not be responsible for damages caused by using a base other than those specified e Please use Wall Mount according to the International standards Downloaded from ManualMonitor com Manuals Troubleshooting 963UW Self Test Feature
26. ssage is displayed again if the system is rebooted There is no image on the screen Is the power indicator on the monitor blinking at 1 second intervals The monitor is in PowerSaver mode Press a key on the keyboard to activate the monitor and restore the image on the screen If there is still no image press the SOURCE 2 button Then press any key on the keyboard again to activate the monitor and restore the image on the screen Connected using the DVI cable You may get a blank screen if you boot the system before you connect the DVI cable or dis connect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals Connect the DVI cable and then reboot the system cannot see the On Screen Display Q A Have you locked the On Screen Display OSD Menu to prevent changes Unlock the OSD by pressing the MENU D button for at least 5 seconds The screen shows strange colors or just black and white Q A A Q z Is the screen displaying only one color as if looking at the screen through a cellophane paper Check the signal cable connection Make sure the video card is fully inserted in its slot Have the screen colors become strange after running a program or due to a crash between ap plications Reboot the computer Has the video card been set properly Set the video card by referring to the video card manual The screen suddenly has
27. to see if the monitor status is set to analog If you still see an error message on the screen when the monitor is connected properly check to see if the monitor status is set to analog Press SOURCE button to have the monitor double check the input signal source Q Ifthe power is on reboot the computer to see the initial screen the login screen which can be seen A Ifthe initial screen the login screen appears boot the computer in the applicable mode the safe mode for Windows ME XP 2000 and then change the frequency of the video card Refer to the Preset Timing Modes If the initial screen the login screen does not appear contact the Service Center or your deal er Q Can you see Not Optimum Mode Recommended Mode 1440 x 900 60 Hz on the screen Downloaded from ManualMonitor com Manuals Troubleshooting You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly Adjust the maximum resolution and frequency that the monitor can handle properly If the display exceeds WSXGA or 75 Hz a Not Optimum Mode Recommended Mode 1440 x 900 60 Hz message is displayed If the display exceeds 85 Hz the display will work properly but the Not Optimum Mode Recommended Mode 1440 x 900 60 Hz message appears for one minute and then disappears Please change to the recommended mode during this one minute period The me
Download Pdf Manuals
Related Search