CopterX CX-CT6A Instruction manual
Contents
1. OK when the adjustment is finished To adjust engine throttle curve to make it more suitable for the model have a better performance and gain better control of the model click Thro Curv There are two parts Normal State NOR and Stunt State IDEL Each curve is made up of five points and each point can be set up individually Adjusted value is from 0 to 100 You may enter the numbers directly from the keyboard Click OK when the adjustment is finished To adjust the helicopter PIT click Pith Curv By this function you can get a better control of the model There are two parts Normal State NOR and Stunt State IDEL Each curve is made up of five points and each point can be set up individually Adjusted value is from 0 to 100 You may enter the numbers directly from the keyboard Click OK when the adjustment is finished To select model click Type There are four models in this system for selection ACRO HELI 90 HELI 120 and HELI 140 Click OK when the adjustment is finished 14 CX CTGA Computer Transmitter Gea To adjust swashplate of CCPM function helicopter for a better control click Swash Afr CH1 CH2 CH4 channels can be adjusted individually Adjusted value is from 0 to 100 You may enter the numbers directly from the keyboard Click OK when the adjustment is finished To use the programmable mixed control function cl2. power supply 5 Check the LED on the receiver If the LED does not flash it means it is successfully matched This process takes about 10 seconds 6 Release the match button on the transmitter Take out the match line 7 Install the servo and then do the test 8 If the test is failed repeat the above steps 9 If the test is successful insert the power supply port into BAT and make the match completed The above steps are only suitable on CopterX 2 4G products Match Line a S P Figure 1 CX CTGA Computer Transmitter Gea 10 02 Boot 1 Connect every part 2 Switch on the power supply 3 Connect the power supply 4 Receive LED light solid 5 Ready for use Tx power ON Rx power ON 10 03 Shut down 1 Cut off the receiver power supply 2 Cut off the transmitter power supply gt Shut down 2 NE i COMPUTER TRANSMITTER Rx power OFF Tx power OFF CX CTGA Computer Transmitter Geek 11 Computer Hardware Connection Steps A programming line is included in this transmitter You may use it to set up the program as you like 1 Install the battery to the transmitter and switch on the power 2 Plug in the programming line to the transmitter port 3 Plug in the other head of the programming line to PC 4 Launch the software program T6CONFIG EXE 5 Click the setting buttons and select programming line port 6 Click GetUser
3. suitable angle for a better control click EndPoint Each servo can be adjusted individually It is divided into left half part and right half part Adjusted value is from 0 to 100 You can enter the numbers directly through the keyboard Click OK when the adjustment is finished To restore click Cancel To change the direction of servo movement click Reverse It keeps the transmitter control direction corresponding to the servo M Click the channel you want to change Click OK when the adjustment is finished System Setting To adjust single space servo for better control of the model click SubTrim Each servo can be adjusted individually Adjusted value is from 120 to 120 You can enter the numbers directly through the keyboard Click OK when the adjustment is finished 13 CX CTGA Computer Transmitter Gea To use double ratio control of CH1 CH2 CH4 channel click DR It gives you the best control of the model It is also a great help for beginners CH1 CH2 CH4 channels can be adjusted individually Adjusted value is from 0 to 100 You may enter the numbers directly from the keyboard This function will only be effective when the DR button is switched on Click OK when the adjustment is finished To adjust the control mode according to one s own habit click Stick There are four different modes for selection Click
4. BO CX CIbA Computer Transmitter INSTRUCTION MANUAL a Channel C HZ 6 channel Radio Digital Propotional Control System Radio Control System www copterx com Copyright 2008 KY MODEL Company Limited CX CTGA Computer Transmitter Table Of COMT ME 000ccccccceeccccccenccccccennccececenseeeeeenneeeeennneesennags 1 1 Introduction 2 2 SEFV CES NNN 2 3 Special Symbols 2 nni 3 A Safety uileS vonu ad 5 Battery Charginy cc000 ona KK KA KKK KKK KE 4 6 Transmitter ParameterS lt lt lt cccr 1 00naa aaa KA J 1 Receiver ParameterS lt lt lt lt lt lt lt srr ron aaa K KKK J 8 Respective Part of the Transmitter lt lt lt lt lt lt c ccoocss aa1n5 6 9 Receiver and Server Connectivity 0 0000 o na n n a n nn 7 10 2 46 Operation NOTES cccccccce ec ccccencccensccecunceeenneceeennesenaneseuas 8 10 01Matching 00 K K KA K KA 8 10 02 Boot ee KK KAR nn 9 10 03 Shutdown ee K K K KA KK g 11 Computer Hardware Connection SteiS 2 2 0000 nn 10 12 Computer Software Installation 0cccccccccecsccccccccccccecneeceeeaes 11 13 Transmitter Function Notes Heli ccccccccccccecscccccecsccecennneess 12 13 01 Sy
5. TGA Computer Transmitter va 6 Respective Part of the Transmitter Antenna Handle HOV Pit Pit Trim Switch B e __ Z Switch A N Elevator Trim Throttle Trim Aileron Throttle Stick Direction Elevator FIR Rudder Trim Alieron Trim Matching yards Keys Power Indicator Light p Power Switch COMPUTER TRANSMITTER i NAM GUDER AND HEUCOPTEASYSTEM DIGITAL PROPORTIONAL RADIO CONTROL SYSTEM Simulant Connector Je Battery Box Battery Cover Charger Port CX CTGA Computer Transmitter Ger 9 Receiver and Server Connectivity When you install the receiver please make sure that it is shown as below Receiver Module Main Receiver 07 CX CTGA Computer Transmitter Gea 10 2 46 Operation Notes This is a 2 4G item with automatic address code Digital transmission mode is used so outside interference can be prevented 10 01 Matching code If you are going to match the receiver with other transmitter please follow the following steps 1 Install the battery in the 2 4G transmitter and shut it down 2 Insert the matching lines to the channel Bat port of the receiver Figure 1 3 Connect the receiver battery to any one of the channel ports If the two LEDs are flashing at the same time this means the receiver is successfully matched 4 Press and hold the button on the transmitter then switch on the
6. button and import the transmitter data to PC 7 Apply programmable settings on the existing parameters onoho TY K PD A UNA Serene A K 10 CX CTGA Computer Transmitter Gea 12 Computer Software Installation With new computer programmable model design all functions of transmitter can be set up through computer 12 01 PC Software Download You can download from our website www copterx com 12 02 PC Software Installation 1 Install driver software PL 2303 Driver Installer exe 2 Install application software t6config exe 3 Restart computer 4 Installation completed 12 03 PC Software Application 1 Install the battery to the transmitter and switch on the power 2 Connect the transmitter programming line and the PC 3 Double click the application icon and the following screen will be shown sj T config Sys i Setting Help Save Open System Setting EndPoint Reverse SubTrim DR Mode Type Thro Cuv Pitch Cuy Swash Afr MIX Switch Program Switch A Switch B VR A vR B Application Interface 11 CX CTGA Computer Transmitter Gea 13 Transmitter Function Notes Heli Connect the transmitter programming line with the PC Switch on the transmitter and start the application software If you choose HELI90 HELI120 or HELI140 the following interface will appear Channel Output Disp
7. ick MIX This system offers three individual mixed control function MIX1 MIX2 MIX3 Source Mixed Control Source Selection Des Destination Selection Up Rate Upper Part s Mixed Control Ratio 100 100 Down Rate Lower Part s Mixed Control Ratio 100 100 Switch Activation Ways OFF ON SWA SWB Click OK when the adjustment is finished 13 03 Switch and Potentionmeters Settings To select setting and function of Switch A or Switch B click Switch A or Switch B You can choose the followings NULL DR Throcut or NOR ID Click OK when the adjustment is finished To select setting and function of both potentiometers click VR A or VR B You can choose the followings NULL or Pith Adjust Click OK when the adjustment is finished 15 CX CTGA Computer Transmitter Gea 14 Content MOC uan nemara 6 Channel 2 4G Transmitter CX CT6A 6 Channel 2 4G 1 Receiver CX CR6B es es 121117 16 Co oR www copterx com Conyright 2008 KY MODEL Company Limited
8. item is not operated by following the instructions minor injuries may be resulted Prohibition Mandatory 4 Safety Guides Do not fly during bad weather such as rain thunder amd wind Before the flying please make sure that the servo corresponds with the elevator stick If they are inconsistent please make adjustment first You need to set the throttle trim down and centre the rest of the trims first then connect the battery After that turn on the transmitter and wait for a few seconds Finally connect the receiver and test the connection by fingering the throttle stick To shut down the power please disconnect the battery to disable the power for the receiver first Afterwards shut down the transmitter power If the above steps are reversed it may cause accident 03 CX CTGA Computer Transmitter Gea J Battery Charging Notes If you use a Ni Cd or Ni MH rechargeable battery please check before the flying If there is a lack of electricity accident may be resulted because of AN inadeguate power or out of control Therefore please charge the battery immediately when the power is low If you recharge a Ni Cd or Ni MH battery please use our company dedicated charger If the electrical current is too large it may lead to overheat and fire AN accident Please cut off the power supply immediately after recharging the ta battery Please take out the battery from the trans
9. lay System Optio System Function Option System Setting EndPoint Reverse SubTrim DR Mode Type Thro Cuy Pitch Cuy Swash Afr MIX Switch Program Switch Program Setting Switch A Switch B VRA VRB System Function Setting 13 01 System Function Option GetUser Import the transmitter data to the PC During programming please use GetUser button to transfer the data to PC after making sure the setting function This helps to prevent the data to be overwritten Clicking Setting as this is useful for the programming line USB port selection It improves the communication of the transmitter and the PC If the selection is wrong there is no data changes and all other settings are invalid Click OK after finishing the selection Clcik HELP on the interface The service information will be offered Copyright KY Model Limited www copterx com 12 CX CTGA Computer Transmitter Gea If you want to save your settings click SAVE on the main interface You can then give it a name and click SAVE to save 1X441 user Fs TIRU EFS Switch Program Switch A Switch B VRIAJ VRIE If you want to open your settings click OPEN on the main interface Select the file and click OPEN to open Switch A Switch B 13 02 System Function Settings To adjust the movement of servo to a
10. mitter if you do not use it within a period Transmitter charger 1 Install the battery in the transmitter with correct direction and cover it 2 Connect the charger to the main connector 3 Connect the charger to the transmitter connector 4 Cut off the power supply immediately after the recharge Rechargeable battery is not included in the transmitter Respective purchase is needed 04 CX CTGA Computer Transmitter Gea 6 Transmitter Parameters Channels 6 Charger port Yes Frequency band 2 4GHz Simulator port PS 2 Power resource 1 5V 8 AA Battery Program type GFSK Modulation type FM RF power 19db Static current lt 250MA Voltage display type LED Size 189 97 218mm Weight 575g Color Black Antenna length 26mm Heli 140 Heli 120 Heli 90 Acro Sub Trim Yes Thro Cuv Programmable Pith Cuv Programmable Support multiple user model Support trim movement Support rudder angle overturned Support rudder angle adjustment Support both hand software adjustment Support swashplate adjustment Support programmable channel output I Receiver Parameters Channel 6 Frequency band 2 4GHz Power resource 1 5V 4 AA Battery Program type GFSK Modulation type FM RF Receiver sensitivity 76db Static current lt 85mA Size 45 23 13 5mm 25 16 8 6 5mm Weight 12g Color Gray semi transparent Antenna length 26mm 05 CX C
11. stem Function OpliON o 00000000 nan n n n nn 12 13 02 System Function Setting c lt lt lt lt c lt cc0000 oa nn 13 13 03 Switches and Potentionmeter SetiingS lt lt lt c lt cc c 2 15 U Content 0 2 0000 KK KA KKK KODAK 16 01 CX CTGA Computer Transmitter Gea 1 Introduction Thank you for choosing 2 4G radio remote control digital products If this is your first time to use this type of products please read this manual carefully and strictly follow the instruction You could refer to the manual if you have any problems during the operation Please keep the manual well because you may have to use it again 2 Services If you have any problems during the operation process please refer to the manual If the problem still exists you may contact our dealers for more information You may also email us at info copterx com CX CTGA Computer Transmitter Gea Special Symbols Please pay attention to the following symbols when they appear on the manual If the item is not operated by following the instructions Danger de sula dini sn serious injuries even mortal danger may be resulted If the item is not operated by following the instructions AAN Warning rem is not operated by following the instru serious injuries even mortal danger may be resulted AN Mtention If the
Download Pdf Manuals
Related Search