fax gsm manual - Eurotech Communication
Contents
1. LCD will display for about 1sec 0 9 Edit Exit 3 Choose a new multiplication factor by pressing 00 09 2 digit number ki 4 Press HET to accept new value and exit 3 Minimum Digits Minimum number of digits to be dialed This parameter allows the user to specify the minimum number of digits to be dialed for any valid outgoing call 1 Press to reach the sub menu The LCD will indicate Change Exit After about a second the LCD display will change to Min 07 2 Press H in order to modify this value LCD will display Min 02 08 for about 1 sec Choose a number between 02 to 08 2 digit number press MEM to accept and exit Note When you have finished dialing the call will go out after the Inter Digit Timer delay menu parameter No 5 but only if the number of digits dialed is between Minimum Digits and Maximum Digits If Minimum Digits is less than 02 no call will go out Winner Analog GSM Fax User Manual 7 www eurotech communication com Euro 4 Maximum Digits Maximum number of digits to be dialed This parameter allows the user to specify the maximum number of digits to be dialed for any valid outgoing call 1 Press to reach the sub menu The LCD will indicate Change Exit After about a second the LCD display will change to Max 09 2 Press in order to modify this value LCD will display Max 05 202. EuroTech WINNER Analog GSM Fax User Manual Version 4 93 EuroTech COMMUNICATION CONTENTS 1 GU ATI 3 1 1 PACKING LIST auraen dikenes faner 3 1 2 Safety Guidelines ap 3 2 QUICK START GUIDE SER IEEE RE Een 4 2 1 User Informationer een eee aen eee 4 2 2 Interference to Medical and Personal Electronic Devices rrrrrnnrrranvrrnnvvrnnnvnrrnvernnr 4 2 3 Antenna Considerations nesena 4 3 INSTALLATION AND SETUP iiisissssisccssssccscssssisccssasstecessssseassascssdassassiossasstecbssssseobsasseibessaiseaesasss 5 3 1 Stage 1 Setting VOICE MOCO vs siccsdsdvccessauscesacterceosancacesdeensdenscdsadesadtivacsaiadencadtvneceasssdes 5 3 2 Stage 2 Setting Fax MOd isccictisscosivescadedesveartevessatecesscanseesacadedesssacveseassiedeuasanceeuadaees 5 3 3 Stage 3 Setting Data Mode wisicci isenciasedediesveccteabcedieccsd ED ERE 6 3 4 Stage 4 DTMF Operation Parameters Men 6 4 GENERAL TECHNICAL INFORMATION ii scosesssssecessssncnnss scnassssecassscssonascssnsinassscsonassessciaasssssoaess 12 4 1 Telephone Line Characteristics 12 4 1 1 RN OKT 12 4 1 2 Normal dialing ET 13 4 2 Enviromental Characteristics ccccccccssccececssececeesnececseseeeceeneeeeseseeeeeeneeeeesseeeeees 13 4 3 MEAD SNS NS 13 Winner Analog GSM Fax User Manual www eurotech communication com 1 1 1 EuroTech COMMUNICATION OVERVIEW PACKING LIST On receiving your WINNER device please inspect the package to ve
3. 1 Answer Supervision AnsSuperVision Off Hook Signal type This parameter allows the user to specify the type of signal sent to the PBX when the phone handset is lifted off the cradle This signal is PBX specific so check your PBX documentation and pay attention to the notes at the bottom 1 Press to enter the sub menu options The LCD will display Choose Save 2 After 1 second the LCD will display Battery Reversal first item in the Sub Menu Winner Analog GSM Fax User Manual 6 www eurotech communication com Euro 3 To scroll between options in the sub menu press ff to choose an option press ikir Available signal types Sub Menu Items Battery Reversal Polarity reverse Disable Double Line Reverse Break Line Polarity reverse timing Pulse Duration can be programmed using menu parameter 2 Answer Supervision Timer Notes 1 The Off Hook Signal is determined by your type of PBX 2 If you are using a CDR Call Detail Record unit use Double Line Reverse as your preferred option 2 Answer Supervision Timer Modify Off Hook Signal Pulse Duration This parameter is in multiplications of 100ms milliseconds see your PBX documentation for the correct value 1 Press to reach the sub menu The LCD will display Change Exit 2 After 1 second the LCD will display 100msX 100ms times 1 User can change the multiplication value by pressing
4. and code identified as WWYY 1 st two digits identify the chronological week in the year 2nd two digits identify the year Hardware and Software version For Example Logo Model No Serial No Rev HardwareX SoftwareY OX OY Date Month Year Winner Analog GSM Fax User Manual 13 www eurotech communication com
5. for about1 sec Choose a number between 05 to 20 2digit number 3 Dress to accept and exit Note When the Maximum Digits number is reached during dialing the call will go out immediately regardless of any superfluous dialing 5 Inter Digit Timer The interval between the end of your dialing sequence and the moment the call goes out This parameter is in multiplications of 5Oms milli seconds 4 Press UT to reach the sub menu The LCD will indicate Change Exit After about a second the LCD display will change to 50msX200 5 Press H in order to modify this value LCD will display for about 1 sec 50msX 001 200 Choose a number between 001 to 200 3 digit number TET 6 Press to accept and exit Note When you have finished dialing the call will go out after the Inter Digit timer delay menu parameter No 5 but only if the number of digits dialed is between Minimum Digits and Maximum Digits If Minimum Digits is less than 02 no call will go out If Maximum Digits is reached during the dialing sequence the call will go out immediately regardless of any superfluous dialing 6 Ignore First Digit This parameter allows you to ignore the first dialing digit 1 Press to reach the sub menu the LCD will indicate Change Exit After 1 second the LCD will display Digit 2 Pressing HIT until LCD shows the digit that you need to ignor
6. D screen and then VOICE MODE appear on the LCD screen SIM READY The unit is ready for Voice calls Default TR RC 3 2 STAGE 2 SETTING FAX MODE gt To set Fax Mode 1 In order to send a fax or press the following sequence on your fax machine 01 the unit will turn to FAX mode 2 To send a fax dial the number and send 3 Once the unit sends the fax the unit will show the following sequences on the LCD gt gt gt INIT LCL FAX the unit is connecting amp initializing sending from fax machine LC FAX TO MEMORY means the fax has been sent and is stored in the unit memory FAX 002 1 PG 002 shows how much of the unit s memory is used 1 PG means 1 PG is in memory DISCONNECTING the unit is disconnecting from the local fax machine CONNECTING the unit connects to destine remote fax machine The unit will show you the last five digits of that fax number CALL TO RM FAX the unit is attempting to call to the remote fax machine MEMORY TO RM FAX the fax has been transferred from the unit s memory to the remote fax machine Winner Analog GSM Fax User Manual 5 www eurotech communication com EuroTech COMMUNICATION 4 To receive a Fax press the following sequence on your fax machine gt If you are not in fax mode then press 401 the unit will turn to FAX mode gt When the fax is being received the unit will show the following sequence Incoming Fac call I
7. MF detection DTMF TX Mute The length in which the voice reception is been silenced so it will not disturb in the DTMF detection DTMF Inter digits the length of restoration between each digit 17 Boot Loader Optional remote programming through comport Enables the user to reprogram upgrade software the unit using a local PC Boot Loader Mode is only available with units that include Data mode This parameter is Optional and can be obtained by special order only For trained personal only Contact your dealer for details Winner Analog GSM Fax User Manual 11 www eurotech communication com EuroTech COMMUNICATION 4 GENERAL TECHNICAL INFORMATION gt v v v v v v 4 1 Electrical Power supply 12 VDC 5 1 2 A 300 mA average in GSM 900 at Tx power Voice 0 5W Data 2W gt 200 mA in idle mode Physical Maximum dimension 114 x 90 x 34 mm Weight 600 g Casing Complete shielding stainless stee Mounting 4 screw holes gt Operating temperature range 5 C to 55 C Optimal storage temperature 35 C to 85 C Analog Telephone LANDLINE PBX interface gt TIP Ring Voltage 48V Line current 25ma gt Ringing Voltage 140 Vpp Load 3REN Crest Factor 1 25 Frequency 20 Hz Cadency 2s 4s Answer supervision Reverse polarity DTMF compliancy gt Dial Tone 400 Hz Busy Tone 400 Hz cadency 500ms 500ms GSM circuit Data Features Data circuit asynchrono
8. e Wek 3 Press to choose and exit Winner Analog GSM Fax User Manual 8 www eurotech communication com Available options 1 Disable Don t ignore any digits 2 0to 9 Set the specific digit to be ignored at the start of the dialed number 3 Any Any first dialed digit will be ignored 7 Software Version Indicates the software version 8 Data Mode Data mode on Data mode off This parameter allows the user to transmit digital data over the GSM An 8 pin serial data cable has to be connected to the serial port Comport off the PC on one side and on other side the RJ45 Once Data Mode ON setting has been done Enter main menu gt gt gt Browse to the data mode menu gt gt gt Enter data mode and choose ON the HyperTerminal has to be accessed Make sure the setting the HyperTerminal is as follows s gzip g p a amame ae MONE ne tents tinno re onh an marang chee te TOR AGM ve ted er ht ml LST ca H em EL SRI mar eg re no nr fu B m npete V RE nal Al 1 Open the HyperTerminalon 19200 frequency This Enables you to send AT Commands Data Note This parameter must be OFF when being used for Voice only 9 Pre Digit Dialling Allows you to transmit a prefix using an ordinary phone This parameter allows you to attach a series of digits i e 050 to every number dialed i e your cell phone prefix number Every time you dial a number this prefi
9. e your WINNER near blasting caps or in a blasting area to avoid the possibility of triggering an explosion Do not operate a WINNER transmitter in a hazardous atmosphere an explosion or fire may result The telephone interface is not designed for outdoor application RJ 11 cable must not be run to an outdoor telephone this minimizes equLandlinement exposure to coupling and directs lightning surges Winner Analog GSM Fax User Manual 3 www eurotech communication com EuroTech COMMUNICATION 2 QUICK START GUIDE 2 1 USER INFORMATION Placement of the device the WINNER GSM gateway unit is designed for installation on a vertical surface but may be mounted also on a wall gt Ifyou wish to mount the device on a wall follow these steps 1 Remove the black metallic strandline used for hanging the unit on the wall by sliding it out from the back of the WINNER unit 2 Place the metallic strandline on the wall to indicate the location of the screws 3 Hold the strandline on the wall and drill holes for the screws to go into the wall through the metallic strandline 4 Place the unit onto the wall by sliding the metallic strandline back into its place 2 2 INTERFERENCE TO MEDICAL AND PERSONAL ELECTRONIC DEVICES Most electronic equipment is shielded from RF energy Nevertheless RF energy from the WINNER transmitter may affect inadequately shielded electronic equipment We therefore advise to consult the manufacturer s of y
10. nit GSM Fax RM FAX TO MEMORY the fax that s being sent to you is stored into the unit s memory gt MEMORY TO LC FAX the fax has been transferred from the unit s memory to your fax machine Note In case the receiving fax machine is busy the unit will store the fax being sent to it s memory In order to re send the fax you will have to press 03 at your convenience The unit will show you the following For example FAX 002 1 PG 03 H to send When a new fax is being received or sent it will overwrite the current fax which in memory 3 3 STAGE 3 SETTING DATA MODE gt Toset Data Mode 1 In order to send or receive data Data Mode has to be on enable at menu 11 in programming mode see DTMF programming press the following sequence on your fax machine HOLH 2 After the COM PORT cable to is connected to PC the following massage will appear on the LCD Data Mode RS 232 Connection In order to revise to VOICE Mode again Please press OO 3 4 STAGE 4 DTMF OPERATION PARAMETERS MENU gt To enter programming mode 1 Pick up the handset of the landline phone and press the star key 3 times 2 LCD will indicate Programming Mode it is now in programming mode after 1 second the LCD will display the first parameter 1 AnsSuperVision 3 In order to scroll through the Programming Options parameter menu press ft 4 To enter any sub menu press 3 4 1 PARAMETER MENU
11. ns 1 By Network According to cellular network 2 Invocation Inactives ID display 3 Suppression ID will be displayed 13 Voice Gain Volume of Caller or Receiver voice 1 Press to reach the sub menu the LCD will indicate Change Exit 2 Scroll through the Sub Menu options using Hf 3 Press for 3 secs in order to change volume setting 3 digits 4 Press to accept the option in the display and exit to the parameter menu Options Rx gain Incoming voice Volume Control Tx gain Outgoing voice Volume Control 14 RX DTMF Restoration Correcting the reception DTMF signal Options for the length of the signal restoration 1 Enable 2 Short 3 Long 4 User See section 16 DTMF Restoration Timers 15 TX DTMF Restoration Correcting the transmission DTMF signal Options for the length of the signal restoration 1 Enable 2 Short 3 Long 4 User See section 16 DTMF restoration timers Winner Analog GSM Fax User Manual 10 www eurotech communication com 16 DTMF Restoration Timers Enable you to choose manually the length of DTMF Restoration 1 Choose Browse 2 Press for Approx 5 Seconds for editing the length 3 Press 3 digits 000 225 4 See OK Options for Editing 1 2 3 5 DTMF RX See section 14 DTMF TX See section 15 DTMF RX Mute The length in which the voice reception is been silenced so it will not disturb in the DT
12. our medical and personal electronic device s for example a pacemaker or hearing aid to determine if they are adequately shielded from external RF energy Do not install a WINNER gateway unit in a health care facility if regulations posted in the area restrict the use of cellular phones Hospitals and health care facilities may be using equipment t that is sensitive to external RF energy 2 3 ANTENNA CONSIDERATIONS Use only the supplied or approved antenna An unauthorized antenna modifications or attachments could affect call quality Winner Analog GSM Fax User Manual 4 www eurotech communication com 3 EuroTech COMMUNICATION INSTALLATION AND SETUP MODE SEQUENCES TABLES gt Voice Mode 00 gt Fax Mode H01 gt Data Mode HO2 gt Sending Fax from Memory WIER Skoll STAGE 1 SETTING VOICE MODE gt Toset the Voice Mode Connect the phone cable to the Winner analog fax via RJ11 connection and the otherend of the phone cable to your fax machine Please insert SIM Card in to the SIM socket Connect the Winner analog fax to the SMA Antenna The fax module will begin initialization process gt gt gt gt gt After a few seconds the word PORT EXPANDER will appear on the LCD screen After a few seconds the word GSM ENGINE will appear on the LCD screen After a few seconds the word VOICE MODE will appear on the LCD screen After a few seconds the NETWORK will appear on the LC
13. rify that you have the following gt 1 Winner GSM analog fax unit gt 1 Communications cable com port 8 Pines gt 1 Phone cable gt 1 Power adapter gt 1SMA Antenna gt 1 Bag with 2 screws amp 2 screw wall plugs gt 1 metal adapter for attaching the fax unit to the wall 1 2 SAFETY GUIDELINES For the safe and efficient operation of your WINNER gateway unit please observe the following guidelines gt Please read the installation instructions and safety guidelines in this User Manual carefully before v v v v v v v v installing the unit Do not handle the equipment before disconnecting it from the electrical outlet Do not use any cleaning agents or detergents on the exterior or interior surfaces If you intend to clean the device disconnect from electrical outlet and use only a damp cloth Do not position device in a damp place do not expose to water Do not expose to extreme temperatures optimal operating temperatures 5 C to 50 C Position equipment in a stable environment any sudden fall or sharp movement may damage the device Do not cover or stick any foreign objects in devices openings or ventilation holes Do not operate your WINNER device while any person is within 0 02m of the antenna A person or object within 0 02 m of the antenna could impair call quality and may cause the phone to operate at a higher power level than necessary Warning Potential Explosive Atmospheres Do not operat
14. us transparent and non transparent up to 14 400 b s Automatic fax group 3 Class 1 amp 2 Alternate speech and fax gt MNP2 V 42bis TELEPHONE LINE CHARACTERISTICS 4 1 1 DTMF DIALING gt Detection level 25dBm to 3dBm gt Ontime 5Omsec gt Offtime 12 characters gt Ringing Signal gt Feeding type Balanced signal gt Distortion Less than 5 Winner Analog GSM Fax User Manual 12 www eurotech communication com EuroTech COMMUNICATION Ring drive capability 3 type A gt Minimum ring Voltage 40 Vrms crest factor 1 2 gt Frequency 20 Hz 4 1 2 NORMAL DIALING TONE Frequency 400Hz Level 2dB Cadence continuous Congestion Busy Tone Frequency 400Hz Level 2dB gt Cadence gt 500ms 20 signal gt 500ms 20 pause 4 2 ENVIROMENTAL CHARACTERISTICS The WINNER complies to the following requirements gt Temperature we claim 5 to 70 Israeli Standard Institute Approval is in process gt Humidity 5 to 95 gt Safety Israeli Standard Institute Approval gt Packing Per EuroTech standard gt Transportation Transport conditions are according to EuroTech Standards gt Storage Condition Storage conditions are according to class 1 1 ETS 300 019 1 1 20 C 80 C 25 C to 65 C 4 3 LABELS Each WINNER labeled as following Product ID located at the box side in future units The label contains product model number Serial number Date
15. x will be added automatically This attribute can save valuable dialing time 1 Press to reach the sub menu the LCD will indicate Change Exit After a short delay the LCD displays String ki 2 Press and write your prefix ie O50 then press Until the LCD display returns to 9 Pre Dialling 10 CID Setup Caller ID Caller I D option This parameter is Optional and can be obtained by special order only Winner Analog GSM Fax User Manual 9 www eurotech communication com If this option is active ON and your PBX Supports this service the caller ID will be sent to the target extension Caller I D will always appear on your LCD with or without this option 11 PIN Number 1 Press to reach the sub menu the LCD will indicate ft Change Exit After a short delay the LCD displays PIN XXXXXX 2 Press to accept the existing No and exit to the parameter menu 3 Press to add a new PIN number or change the current PIN No NEW PIN will be displayed Key in a PIN number max 8 digits using the telephone keypad 4 Press to accept the PIN number and exit to the parameter menu 12 CLIR Mode CLIR ClearCaller ID 1 Press to reach the sub menu the LCD will indicate Change Exit 2 Scroll through the Sub Menu options using ft 3 Press to accept the option in the display and exit to the parameter menu Available optio
Download Pdf Manuals
Related Search