CRU DE75, Frame Only, ATA/133
Contents
1. Rugged Reliable Mobile Secure Data Express DE75 ATA 133 Install Guide Removable Ultra ATA133 Drive Enclosure Drive Installation Overview tect vocal nN 2 Sprays amp SRS FA saa Receiving Frame Motherboard sae Lo rey unger Donet mnom Receiving Frame Motherboard Rear View Recei ng Frame Motherboard DC Power Connector P1 The Data Express uses a standard 4 pin DC Power Connector to accept DC power 1 0 Connector JP1 The input output connector provides a standard interface for all IDE signals 300 260 9800 JP6 Header Master Slave Setting JP6 IDO amp ID1 1D0 Jumper installed on Pins 1 amp 2 Factory Default for Master configuration 1D1 Jumper installed on Pins 3 amp 4 for Slave configuration Remote Drive Activity JP6 RLED Pins 17 amp 18 are used for remote drive activity Jumper JP6 DDA Factory installed on Pins 15 amp 16 Do not remove JP4 Option Refer to the full version of the DE7Si A100 Manual for further information Master Slave Drive Selection There are two 2 ways to set the Master Slave drive designation for the DE7Si A100 unit Method 1 Recommended Using the factory installed jumper on your IDE drive In most cases the drive will be factory configured as a Master Ultra ATA133 drive using a jumper plug on the drive itself No configuration changes are required For multiple drive2. configura tions it is necessary to set the first IDE drive as Master and the second IDE drive to Slave This can be done by changing the jumper on the Ultra ATA133 drive itself refer to your drive manu facturer documentation This method requires no additional configuration ofthe drive car rier circuit board gt www CRU DataPort com Rugged Reliable Mo However the appropriate jumper setting must still be configured on JP6 IDO amp ID located on the receiving frame motherboard Figure 2 For Master setting install jumper on IDO Pins 1 amp 2 For slave setting install jumper on 1D1 Pins 3 amp 4 Skip the Method 2 section and continue with installation Method 2 Using the hard wire connector JP3 on the drive carrier circuit board to allow drive carrier interchangeability between Master Slave configured receiving frames To allow this interchangeabilty it is necessary to set the Mas ter Slave drive selection by a hard wire connection between the drive and the drive carrier circuit board This method requires the fabrication of a cable wire not pro vided Refer to the DE7Si A100 Manual for further information regarding Method 2 Unit ID Select Switch Settings The following table lists the unit ID select switch settings and the valid AT IDE unit numbers Invalid switch settings are indicated by an X and will result in a blank display in the receiving frame window Unit ID Sel
3. ect Switch Settings Note The unit ID number display is for ID display purposes only The master slave setting must still be set on the drive itself refer to the drive manufacturer s documentation for further information Selecting the Ur vided to select the D Number Use the alignment tool pro number of the disk drive Unit ID Select Switch Location igen al Note The lock on the Data Express serves as a power switch It must be engaged turned counterclockwise for the Data Express to power up and function properly Limited Product Warranty CRU DataPort CRU warrants the Data Express DE7S to be free of significant defects in material and workmanship for a period of five years from the original date of purchase CRU s warranty is nontransferable and is limited to the original purchaser ity The warranties set forth in this agreement replace all other war ranties CRU expressly disclaims all other warranties including but not limited to the implied warranties of merchantability and fit ness for a particular purpose and non infringement of third party rights with respect to the documentation and hardware No CRU dealer agent or employee is authorized to make any modifica tion extension or addition to this warranty In no event will CRU or its suppliers be liable for any costs of procurement of substi tute products or services lost profits loss of information or data computer malfunction or any othe
4. r special indirect consequen tial or incidental damages arising in any way out of the sale of use of or inability to use any CRU product or service even if CRU has been advised of the possibility of such damages In no case shall CRU s liability exceed the actual money paid for the products at issue CRU reserves the right to make modifications and addi tions to this product without notice or taking on additional liability Limitation of Lial Certification EMI Standard FCC Part 15 Class B CE EMC Standard EN55022 ENS5024 FCC Certification This device has been tested and found to comply withthe limits for a Class B digital device pursuant to Part 15 of the FCC rules Operation is subject to the following two condi tions 1 This device may not cause harmful interference 2 This device must accept any interference received includ ing interference that may cause undesired operation Register your product at www CRU DataPort com A7 075 0004 Rev 2 1 gt 1 800 260 9800 gt www CRU DataPort com
Download Pdf Manuals
Related Search