User Manual Trinocular Stereo Microscope
Contents
1. Cover the microscope with the dust cover when not in use 1 Components Illustration Jo 01 R WD Photo Tube Stand Post Trinocular Body Eyepiece Photo Switch Thumb Screw Focus Knob Focus Block 10 11 12 13 14 Post Collar Incident Light Intensity Dial Transmitted Light Intensity Dial Eyepiece Diopter Ring Eyepiece Tube Zoom Knob www microscopenet com 15 16 17 18 19 20 21 Holding Ring Objective Housing Incident Light Power Switch Stage Clip Stage Plate Base OMAX www microscopenet com 2 Installation 2 1 Install the microscope body 2 1 1 Loosen the thumb screw on the body holding ring 2 1 2 Sit the body into the holding ring firmly 2 1 3 Tighten the thumb screw 2 2 Install the eyepieces 2 2 1 Take off the plastic covers on the eyepiece tubes 2 2 2 Insert the eyepieces into the eyepiece tubes 2 3 Adjust the focus block 2 3 1 Loosen the knob on the focus block E 2 3 2 Slide the focus block up or down on the stand post so that the distance between the bottom of the objective housing and the OM stage plate is about 95mm with no auxiliary lens or 150mm with 0 5X auxiliary lens on And then tighten the knob 2 3 3 Slide the post collar to against the focus block as showed in the figure and then tighten its knob 2 4 Replace the incident light bulb 2 4 1 Turn the power off and disconnect the power cord 2 4 2 Allow some time to cool down the lamp 2 4 3 Take2. E A9254 A9254P 54 LEDs Macro Ring Light A9264S 64 LEDs Macro Ring Light GA g A92144B 144 LEDs Macro Ring Light o i io A92144L 144 LEDs Macro Ring Light A92144S 144 LEDs Macro Ring Light D ee _ T 6 1 3 Auxiliary Objective Lens TO vwa o oo O O A1530 2048 x 1536 3 0MP MS Windows 32bit E AJ5D75AUX 0 75X 10
3. the zoom knob for the desired magnification 3 3 5 Adjust the focus knob slightly to get clear image 3 4 Adjusting interpupillary distance While observing with both eyes hold the left and right eyepiece tubes and swing inwards or outwards The interpupillary y distance is correct when the left and right fields of view converge completely into one image _ 3 5 Adjusting eyepiece diopter 3 5 1 Turn the diopter rings on both eyepiece tubes at 0 positions 3 5 2 Using your right eye only observe your specimen through the right eyepiece and bring it into focus by adjusting the focus knob 3 5 3 Then observe the specimen with your left eye only through the left eyepiece If the specimen is not in focus rotate the diopter ring until a sharp image is obtained 3 6 Adjust the light 3 6 1 Plug in the power cord to a power outlet 3 6 2 Turn the switch to the I position to turn on the power y 3 6 3 Turn the switch to the O position to turn off the power gt 3 6 4 Turn the incident light intensity dial to turn the incident light on and adjust the intensity oa su BB 3 6 5 Turn the transmitted light intensity dial to turn the transmitted light ast on and adjust the intensity 3 7 Adjust the ring light optional 3 7 1 Install the ring light and connect the AC adapter to the power outlet 3 7 2 Turn on the power button on the ring light 3 7 3 Adjust the intensity dial OMAX www microscopenet com 3 8
4. Camera optional 3 8 1 Install the camera following the procedures in 2 8 3 8 2 Focus the microscope following the procedures in 3 3 3 8 3 Pull out the switch bar 3 8 4 Open the software of the camera and launch the live view window 3 8 5 If the live view image is not in focus loosen the thumb screw showed in the right figure turn the plastic part of the photo tube to adjust the photo tube height till the image is in focus then tighten the thumb screw 3 8 6 You can observe image snap picture and capture video pieced in the software Note1 Please refer to the User Manual in the Camera CD for Thumb the software operation me Note2 The camera is optional and may have different color SS vien a and shape from the one in the picture depends on the n m model purchased OMAX www microscopenet com 4 Specifications Trinocular 45 inclined 360 swiveling Microscope body Adjustable Interpupillary distance 55 75mm 2 3 16 2 15 16 Adjustable diopter on both eyepiece tube 5dp ENS 1 pair of WF10X yep 1 pair of WF20X optional Obiectives Zoom 0 7x 4 5x ratio 6 5 1 Auxiliary lens 0 5X optional Focusing Mechanism Rack and pinion focusing knobs on both sides 95 mm 3 3 4 Working Distance 152 mm 6 with 0 5X auxiliary lens on Frosted glass plate 95mm 3 3 4 in diameter Stage Plate White black plastic plate 95mm 3 3 4 in diameter Incident upper 12V 10W halogen light Il
5. User Manual Trinocular Stereo Microscope Model JAA Series MicroscopeNet com Table of Contents o isa 1 ii Care and Maintenance LL 2 Le omponent MUST Ono 3 2 WAS MU 4 SUPE 6 ad SPECHICAID Siae 8 5 Troubleshooting Guld rai na 9 D ODIODal ses E ia sv a ee Dux cx Ry 10 OMAX www microscopenet com i Caution 1 Find the UP sign and place the Styrofoam container on your table or bench so that the arrow is pointing upward Open the shipping carton carefully to prevent any accessory like eyepieces from dropping and being damaged 2 Do not discard the molded Styrofoam container The container should be retained should the microscope ever requires reshipment 3 Keep the instrument out of direct sunlight high temperature or humidity and dusty environments Ensure that the microscope is located on a smooth level and firm surface 4 f any specimen solutions or other liquids splash onto the stage objective or any other component disconnect the power cord immediately and wipe up the spillage Otherwise the instrument may be damaged 5 Important the lamp lamp housing and adjacent parts will become very hot Do not touch these parts until they have completely cooled Never attempt to handle a hot halogen bulb 6 All electrical connectors power cord should be inserted into an electrical surge suppressor to prevent damage due to voltage fluctuations 7 For safety when replacin
6. g the halogen lamp or fuse be sure the main switch is off unplug the power cord and only replace the halogen bulb after the bulb and the lamp house has completely cooled 8 Confirm that the input voltage indicated on your microscope corresponds to your line voltage The use of a different input voltage other than that as indicated will cause severe damage to the microscope OMAX www microscopenet com ii Care and Maintenance 1 Do not attempt to disassemble any component including eyepieces objectives or focusing mechanism Keep the instrument clean remove dirt and debris regularly Accumulated dirt on metal surfaces should be cleaned with a damp cloth More persistent dirt should be removed using a mild soap solution Do not use organic solvents for cleansing The outer surface of the optics should be inspected and cleaned periodically using an air stream from an air bulb If dirt remains on the optical surface use a soft cloth or cotton swab dampened with a lens cleaning solution available at camera stores All optical lenses should be swabbed using a circular motion A small amount of absorbent cotton wound on the end of a tapered stick makes a useful tool for cleaning recessed optical surfaces Avoid using an excessive amount of solvents as this may cause problems with optical coatings or cemented optics or the flowing solvent may pick up grease making cleaning more difficult Store the instrument in a cool dry environment
7. lumination Transmitted lower 12V 10W halogen light With switch and intensity dials separately Power Supply Microscope AC 110V 240V 50 60Hz Dimension 23cm x 16cm x 44cm 9 x 6 x 17 1 2 Net weight 6 kg 13 Ib OMAX www microscopenet com 5 Troubleshooting Guide Totally dark in the The cover of objectives is Take off the cover of objectives view field still on poque i Clean the lens with a camera cleaning kit Stains or dust on the JSP J field of view l Stains or dust on the Clean the specimen specimen mE Adjust the height of the focusing Mpeg meds da mechanism so that the distance between Can not focus to the specimen and out of the objectives and specimen is about the range of focus stroke 95mm with no auxiliary lens or 152mm with 0 5X auxiliary lens on Image moves while opecimen rises from stage focusing surface No electrical power Check power cord connection Lamp does not light Lamp bulb burnt out Replace bulb when switched on Fuse blown out Replace fuse Secure the specimen OMAX www microscopenet com 6 Optional Parts The optional parts may be included in some models or sold separately a we 640 x 480 0 3MP gf A1510 1280 x 1024 1 3MP MS Windows 32 64bit EUM A1520C 1600 x 1200 2 0MP A Included 6 1 1 Camera A A1550 2592 x 1944 5 0MP TT 32 64bit A A1590 3488 x 2616 9 0MP 1 6 1 2 Illuminator Wd hm I 128W Fluorescent Ring Light A9239 39 LEDs Macro Ring Light
8. off the black light housing by turning it counterclockwise 2 4 4 Pull the bulb with reflector out gently 2 4 5 Align the two pins of the bulb with the sockets then press the light bulb gently in 2 4 6 Put the light housing on and tighten by turning it clockwise Light Housing Light Bulb 2 5 Replace the transmitted light bulb 2 5 1 Turn the power off and disconnect the power cord 2 5 2 Allow some time to cool down the lamp 2 5 3 Turn over the microscope on its side find the light compartment at the bottom 2 5 4 Open the cover of the compartment by loosening the screw 2 5 5 Take out the dead bulb and insert the new bulb Be sure the pins on the bulb are completely inserted into the lamp socket 2 5 6 Put the cover back and tighten the screw Screw Light Compartment Light Bulb OMAX www microscopenet com 2 6 Replace the fuse 2 6 1 Pry out the fuse holder with a screw driver 2 6 2 Install replace the fuse 2 6 3 Insert the fuse holder back to its place 2 7 Install the auxiliary lens optional 2 1 Screw off the plastic cover on the bottom of objective housing 2 2 Screw on the auxiliary lens onto the objective housing Note The auxiliary lens is optional and may have different color and shape from the one in the picture depends on the model purchased 2 8 Install the camera optional 2 8 1 Take off the plastic cover on the phototube 2 8 2 Insert the camera into the phototube and then c
9. onnect the camera to a computer by a USB cable 2 8 3 Refer to the manual in the Camera CD to installation the driver and software Note The camera is optional and may have different color and shape from the one in the picture depends on the model purchased 2 9 Install the ring light optional 2 9 1 Screw off the plastic cover on the bottom of objective housing 2 9 2 Screw on the ring light adapter onto the objective housing Fuse Holder Hz 12V20W F Auxiliary Lens N Camera 4 Photo Tube 2 9 3 Put the ring light on to the ring light adapter Tighten the 3 screws Make sure the end of the screws stick into the groove of the adapter Note The ring light is optional and may have different color and shape from the one in the picture depends on the model purchased Ring Light Adapter Ring Light OMAX www microscopenet com 3 Operation 3 1 Change the stage plate 3 1 1 Loosen the stage lock screw at the front of base 3 1 2 Take off the glass plate and put on the white black plate or vice versa 3 1 3 Tighten the set screw Thumb Screw 3 2 Place the specimen 3 2 1 Put the specimen in the center of the stage plate 3 2 2 Hold the specimen with the stage clips if necessary Ah SS T 2 3 3 Focusing 3 3 1 Turn the zoom knob at 0 7 3 3 2 Turn the focus knob until the specimen is in focus 3 3 3 Move the interesting spot of specimen into the center of field of view 3 3 4 Turn
Download Pdf Manuals
Related Search