SBC84600 User`s Manual
Contents
1. 41 5 2 2 Advanced BIOS Features 45 5 2 3 Advanced Chipset Features 50 5 2 4 Integrated Peripherals 53 5 2 5 Power Management Setup 56 5 2 6 PNP PCI Configuration 59 5 2 7 PC Health Status 61 5 2 8 Frequency Voltage Control 62 5 2 9 Load Fail Safe Defaults 63 5 2 10 Load Optimized Defaults 64 5 2 11 Set Supervisor User Password 65 5 2 12 Save amp Exit Setup 66 5 2 13 Exit Without Saving 67 Appendix A Watchdog Timer 69 vi Table of Contents SBC84600 All in One CPU Board Series User s Manual Chapter 1 Introduction 1 1 General Description The SBC84600VE is a featured pack CPU Board designed for industrial purpose It provides reliable high performance and function rich capability The onboard CPU incorporates the VIA VT8606 chipset and the VT82C686B with built in AGP 4x VGA controller the PC 104 bus is available for further expansions Its 8 layer structure reduces signal noise and me2. gt E Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults At the bottom of the menu are the control keys for the use of this menu The lt F1 gt key can be pressed in each item field to display the relevant information for help The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following pages describe each item of this menu Award BIOS Utility 41 SBC84600 All in One CPU Board Series User s Manual L Date The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar day The day of week from Sun to Sat determined by the BIOS is read only The date from 1 to 31 or the maximum allowed in the month can date c key in the numerical function key month The month Jan through Dec year The year depends on the year of BIOS 6 Time The time format is lt hour gt lt minute gt lt second gt accepting either function key or numerical key The time is calculated based on the 24 hour military time clock For example 1 p m is 13 00 00 6 IDE Primary Master Primary Slave Secondary Master Secondary Slave This category identifies the type of the channel that is installed in the computer There are 45 predefined types and 2 user definable types for Enhanced IDE BIOS Type 1 to Type 45 a
3. Award BIOS Utility 61 SBC84600 All in One CPU Board Series User s Manual 5 2 8 Frequency Voltage Control This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value CMOS Setup Utility Copyright 1984 2001 Award Software Frequency Voltage Control Auto Detect DIMM PCI Clk Enabled Spread Spectrum Disabled Menu Level gt CPU Host PCl Clock Default gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Auto Detect DIMM PCI Clk When enabled this item will auto detect if the DIMM and PCI socket have devices and will send clock signal to DIMM and PCI devices When disabled it will send the clock signal to all DIMM and PCI socket The choice Enabled Disabled Spread Spectrum This item is to enable disable the spread spectrum modulate The choice Enabled Disabled 62 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 9 Load Fail Safe Defaults This option is to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Opti
4. PNP OS Installed No Item Help Reset Configuration Data Disabled Menu Level gt Resources Controlled By Auto ESCD X IRQ Resources Press Enter Select Yes if you are X DMA Resources Press Enter using a Plug and play capable operating PCI VGA Palette Snoop Disabled system select No if Assign IRQ For VGA Enabled you need the BIOS to Assign IRQ For USB Enabled configure non boot devices gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PNP OS Installed This item is to determine install PnP OS or not The options available are Yes and No Reset Configuration Data Normally this field is Disabled Select Enabled to reset Extended System Configuration Data ESCD When exiting Setup or installed a new add on the system reconfiguration has caused such a serious conflict that the operating system cannot boot The options available are Enabled and Disabled Award BIOS Utility 59 SBC84600 All in One CPU Board Series User s Manual 1 Resource controlled by The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and the Plug and Play compatible devices However this capability means absolutely nothing unless using a Plug and Play operating system such as Windows 98 The options available are Auto and Manual IRQ Resources When resources are controlled manually assign e
5. CN12 26 3 4 11 Keyboard and PS 2 Mouse Connectors CN13 27 Table of Contents V 3 4 12 Composite Video Output CN14 VIDEO Optional Feature ee 27 3 4 13 FDD Connector CN15 28 3 4 14 Mini Pci Type I Connector CN16 28 3 4 15 USB Connectors USB1 and USB2 29 3 4 16 Ethernet PJ 45 Connector LAN1 30 3 4 17 PC 104 Connectors J1 and J2 31 3 4 18 Serial Port Interface 32 3 4 19 Compact Flash Connector CF1 33 Chapter 4 Hardware Description 35 4 1 Microprocessors 35 4 2 BIOS 22 22 oeeo eree eee oeeo eee eooo eooo neee 35 4 3 Real Time Clock and CMOS RAM 35 4 4 System Memory 35 4 5 VGA Interface 0 022020020 0 36 4 6 I O Port Address Map 37 4 7 Interrupt Controller 38 Chapter 5 Award BIOS Utility 39 5 1 BIOS Introduction 39 62 DIOS Setup eee 39 5 2 1 Standard CMOS Setup
6. Description A ps ora Ps see 6 serie SS 28 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual Pin Description Pin Description Pin Description s ow fej awe eo o ER T a ADB RESERVED GND O O CO OININININI OD j loOlO M O MD WloI Nis 2 2 2 2 ojlojlojo Ca ne fe ne e e o ne 1 oo fo nc _ RT se O S S 3 4 15 USB Connectors USB1 and USB2 There are two USB connectors allow installation of USB devices USB1 is 4 pin header connector and USB2 is a single standard USB connector The following table shows the pin outs of the USB connectors Signal Name USB Vcc USB GND Jumpers and Connectors 29 SBC84600 All in One CPU Board Series User s Manual 3 4 16 Ethernet PJ 45 Connector LAN1 The SBC84600VE is equipped with a high performance Plug and Play Ethernet interface which is fully compliant with the IEEE 802 3 standar and consisting of a RJ 45 connector LAN 3 4 16 1 Pin Assignment LANI RJ 45 Connector Pin Assignment Pin Signal 1 Tx Data transmission positive Tx Data transmission negative 12345678 Rx Data reception positive RJ45 termination _ RJ45 termination 6 Rx Data reception negative RJ45 termination RJ 45 8 RJ45 termination 3 4 16 2 Feature 10Mb s and 100Mb s operations Supports 10Mb s and 100Mb s N Way auto negotiation Full duplex capability Full compliance with PCI Revision
7. E Wear a wrist grounding strap available from most electronic component stores when handling boards and components Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd IBM is a registered trademark of International Business Machines Corporation MS DOS and Windows 98 NT 2000 XP are trademarks of Microsoft Corporation Award is a trademark of Award Software Inc IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation VIA C3 and other trademarks of VIA Technology Realtek RTL 8139C are registered trademark of Realtek Semiconductor Corporation Other brand names and trademarks are the properties and registered brands of their respective owners This page does not contain any information Table of Contents Chapter 1 Introduction 1 1 General Description 00 00 0 1 1 2 Specifications 2 Chapter 2 Installation 5 2 1 Installation Steps 5 2 2 Peripherals for a Minimum System 5 Chapter 3 Jumpers and Connectors 7 3 1 Jumpers and Connectors Layout 7 3 2 Jumpers and Connectors Dimensions 8 3 3 Jumper Settings 20 0 9 3
8. Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Award BIOS Utility 45 SBC84600 All in One CPU Board Series User s Manual Virus Warning This item protects the boot sector and partition table of the hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning message If this occurs the user can either continue the operation or run an anti virus program to locate and remove the problem NOTE Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning Thus disable the Virus Warning feature while running any of these programs CPU Internal Cache External Cache Cache memory is additional memory that is much faster than conventional DRAM system memory CPUs from 486 type and up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These items are used to enable speed up memory access or disable the cache function By default these are Enabled CPU L2 Cache ECC Checking When enabled this allows ECC checking of the CPU s L2 cache By default this field is Enabled Processor Number Feature When a Pentium III CPU is installed the system automatically detects it and displays this item Quick Power On Self T
9. The following table lists the function of each connector on the SBC84600VE Connectors 44 Pin IDE Connector 44 pin LCD Connector Flat Panel Bezel Connector 20 pin LCD Connector CPU FAN 5V Connector Printer Port Connector Digital lO Port Conntctor ATX Power On Off Button Power Input Connectors IrDA Connector AC97 Link Interface Keyboard and Mouse Conntctor TV Connector FDD Connector Mini pci Type USB connector VGA CRT Connector Ethernet Connector PC 104 Connector COM Connector COM Connector COM Connector COM Connector Compact Flash Connector VIDEO Connector alo E Q ed fo G Q zZ ojo Zl ST USB1 USB2 VGA1 LANT J1 J2 COM1 COM2 COM3 COM4 C VIDEO 70 ROL H ojo z z Dja Jumpers and Connectors 13 SBC84600 All in One CPU Board Series User s Manual 3 4 1 Enhanced IDE Interface Connector CN1 The SBC84600VE includes a PCI bus enhanced IDE controller that can support master slave mode and post write transaction mechanisms with 64 byte buffer and master data transaction 44 pin IDE Interface Connector Description Description i Description Reset 1 oo zz ND lms Tra s emt 14 GND Data 7 met fe ome baat 8 foa GND IOCHRDY HDC CSI HDD Active C Se Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 4 2 Flat Panel Bezel Connector CN3 CN3 Power LED This 2 pin connector designated at
10. 5 pin IrDA connector for wireless communication CN11 BV l DH 1 Nc OF 2 IRRX OF 3 GND D 4 IRTX OF 5 3 4 10 AC97 Interface Link Connector CN12 CN12 is a AC97 Interface Link Connector for Audio KIT CN1i2 26 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 4 11 Keyboard and PS 2 Mouse Connectors CN13 The SBC84600VE provides a keyboard and Mouse interface CN13 is a DIN connector for PS 2 keyboard Connection VIA Y Cable CN1i3 Mouse Clock 3 4 12 Composite Video Output CN14 VIDEO1 Optional Feature The SBC84600VE provides a PC99 compliant soulution for TV output Composite Video Output CN14 Pin Signal l COMP Y G S Video Output VIDEO1 Pin Signal 1 GND CSYNC CHROMA VIR LUMA U B The S Video Output is use a 4 pin Wafer with box 2 0mm Jumpers and Connectors 27 SBC84600 All in One CPU Board Series User s Manual 3 4 13 FDD Connector CN15 The SBC84600VE provides a 26 pin FCC Z I F type connector and the general output supports a single floppy drives The floppy drive could be any one of the following types 3 5 720KB or 1 44MB 2 88MB CN15 FDD Connector Pin Assignment Description Pin Description 5V 4 STEP w R HT ee e we N oi TRKO mo f RDATA mr s N N 3 4 14 Mini Pci Type Connector CN16 CN16 Connector Pin Assignment Pin Description Pin Description Pin
11. CPU Board Series User s Manual PM Control by APM When enabled an Advanced Power Management device will be activated to enhance the Max Power Saving mode and stop the CPU internal clock If Advance Power Management APM is installed on the system selecting Yes gives better power savings If the Max Power Saving is not enabled this will be preset to No Video Off Option When enabled this feature allows the VGA adapter to operate in a power saving mode Always On Monitor will remain on during power saving modes Monitor blanked when the system enters the Suspend mode Suspend gt Off s Stbv lt gt Off Monitor blanked when the system enters either Suspend or usp Stby Standby modes Monitor blanked when the system enters any power saving All Modes gt Off mod 6 Video Off Method This determines the manner in which the monitor is blanked V H SYNC This causes the system to turn off the vertical and horizontal Blank synchronization ports and write blanks to the video buffer Select this option if your monitor supports the Display Power Management Signaling DPMS standard of the Video Electronics Standards to select video power management values Blank Screen This option only writes blanks to the video buffer 6 Video Off Method In suspending this item is to select the CRT closed method under APM mode The choice Blank Screen V H SYNC Blank DPMS MODEM Use IRQ APM 1 2 fu
12. Pins 1 and 5 connects the system power LED indicator to its respective switch on the case Pin 1 is and pin 5 is assigned as The Power LED lights up when the system is powered ON External Speaker and Internal Buzzer Connector Pins 2 4 6 and 8 of CN3 connect to the case mounted speaker unit or internal buzzer Short pins 4 6 when connecting the CPU card to an internal buzzer When connecting an external speaker set these jumpers to Open and install the speaker cable on pin 8 and pin 2 System Reset Switch Pins 9 amp 11 of CN3 connect to the case mounted reset switch and allow rebooting of your computer instead of turning OFF the power switch This is a preferred method of rebooting in order to prolong the life of the system s power supply HDD Activity LED This connector extends to the hard drive activity LED on the control panel This LED will flash when the HDD is being accessed Pins 10 amp 12 of CN3 connect the hard disk drive and the front panel HDD LED Pins 10 is and pin 12 is assigned as Jumpers and Connectors 15 SBC84600 All in One CPU Board Series User s Manual 3 4 3 VGA Flat Panel Connector VGA1 CN2 CN4 The SBC84600VE has three connectors that support CRT VGA and flat panel displays individually or simultaneously VGA1 is a standard 15 pin pin header connector commonly used for the CRT VGA display and CN2 44 pin CN4 20 pin are dual in line headers for the flat panel connection C
13. assignments are listed on the following table Pin Description Pin Description 4 Dat Carir Detect 00D 2 Dansere os 15 DI 5 TrensnitDaia 7X0 6 oearosearcrs gt la alg oo pao nc CS 32 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual The RS 422 485 pin assignments for COM72 are listed below Signal Name TX DATA N 7 10 3 4 19 Compact Flash Connector CF1 The SBC84600VE Series is equipped with a CompactFlash disk socket on the solder side and it supports the IDE2 interface CompactFlash disk card The socket itself is specially designed to prevent any incorrect installation of the CompactFlash disk card When installing or removing the CompactFlash disk card make sure the system power is off The CompactFlash disk card is defaulted as the E or F disk drive in the PC system Jumpers and Connectors 33 SBC84600 All in One CPU Board Series User s Manual This page does not contain any information 34 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual Chapter 4 Hardware Description This chapter gives a detailed explaination of the hardware features of the SBC84600VE CPU Board 4 1 Microprocessors The SBC84600VE supports VIA EDEN 400MHz 667MHz or C3 800MHz C3 1G CPU other frequency processors are manufacturer optional Systems based on these CPUs can be operated under Windows XP NT 2000 98 Me and
14. interface with support for two IDE channels Select Enabled to activate each channel separately The choice Enabled Disabled IDE Prefetch Mode The onboard IDE drive interface supports IDE prefetching for faster drive accesses If a primary and or secondary add in IDE interface are installed set this field to Disabled if the interface does not support Award BIOS Utility 53 SBC84600 All in One CPU Board Series User s Manual prefetching e Primary Secondary Master Slave PIO The four PIO Programmed Input Output fields sets a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device The choice Auto Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Primary Secondary Master Slave UDMA Ultra DMA 33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 98 or a third party IDE bus master driver If the hard drive and the system software both support Ultra DMA 33 select Auto to enable BIOS support The Choice Auto Disabled Init Display First This item is to active whether PCI Slot or on chip VGA first The choice PCI Slot Onboard IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If the IDE hard drive
15. or EDO extended data output DRAMs The available choices are 66 MHz and Host CLK SDRAM Cycle Length When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing Do not reset this field from the default value specified by the system designer The default setting is 3 Memory Hole To improve performance certain space in memory is reserved for ISA cards This memory must be mapped into the memory space below 16MB The available choices are 15M 16M and Disabled P2C C2P Concurrency This item enables or disables the PCI to CPU and CPU to PCI concurrency By default this field is set to Enabled System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result The choice Enabled Disabled Video RAM Cacheable Selecting Enabled allows caching of the A B segment resulting in better system performance The choice Enabled Disabled AGP Aperture Size The field sets aperture size of the graphics The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The choice 4M 8M 16M 32M 64M 128M and 256M OnChip USB This should be enabled if the system has a USB installed on the system
16. supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support The choice Enabled Disabled Onboard FDD Controller Select Enabled if the system has a floppy disk controller FDC installed on the system board and the FDC will be used If the and in FDC are installed or the system has no floppy drive select Disabled in this field The choice Enabled Disabled Onboard Serial Port 1 Port 2 Select an address and corresponding interrupt for the first second and twist serial ports The choice 3F8 IRQ4 2E8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto 54 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual UART 2 Mode This item a is to select UART mode By default this field is set to Standard IR Function Duplex This item is to select the IR half full duplex funcion TX RX inverting enable This item is to enable the TX RX inverting which depends on different H W requirement This field is not recommended to change its default setting for avoiding any error in the system Onboard Parallel Port This item is to determine access onboard parallel port controller with which I O address The choice 3BC IRQ7 378 IRQ7 278 IRQ5 Disabled Onboard Parallel Mode Select an operating mode for the onboard parallel printer port Select Normal Compatible or SPP unless you are certain y
17. 2 JP2 SBC84600VE supports both 3 3V and 5V flat panel displays Configure the jumper JP2 to the appropriate voltage of the flat panel Settings 1 Short 1 2 3 3V default Short 2 3 S 3 3 3 CMOS Clear Jumper JP3 Options Settings Clear CMOS Short 2 3 Normal default Short 1 2 10 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 3 4 COM2 RS232 422 485 Settings JP4 JP5 JP6 COM2 JP4 JP5 JP6 RS 232 default Short 1 2 Short 3 5 4 6 Short 3 5 4 6 RS 422 Short 3 4 Short 1 3 2 4 Short 1 3 2 4 RS 485 Short 5 6 7 8 Short 1 3 2 4 Short 1 3 2 4 JP4 JP5 and JP6 7 5 3 6 oO of 5 oo 4 1 a oO 2 nm oO L O 3 3 5 Power Supply Type Selection JP7 Options Settings AT P S Short 1 2 default Options Setting Pin 1 5V Short 1 3 3 3 7 Options Setting Pin 1 5V Short 1 3 2 Pin 1 DCD Short 2 3 default 1 Jumpers and Connectors 11 SBC84600 All in One CPU Board Series User s Manual 3 3 8 COM4 Signal 5V Selection JP10 Options Setting Pin 1 5V Short 1 3 Options Setting Pin 1 5V Short 1 3 Options Setting Short 2 3 5V 12 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 4 Connectors The connectors allow the CPU Board to connect with other parts of the system Ensure that all connectors are in place and firmly attached
18. 2 1 PCI Bus Master data transfers 3 4 16 3 Drivers Supported Bundled with popular software drivers the SBC84600VE Ethernet interface allows great flexibility to work with all major networking operating systems including Novell NetWare v2 x v3 x v4 x Microsoft LAN Manager Win3 1 Win NT Win95 IBM LAN Server SCO UNIX or other ODI NDIS and Packet drive compliant operating systems 30 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 4 17 PC 104 Connectors J1 and J2 The PC 104 is an industrial standard It is a compact form factor with dimensions of 3 6 x 3 8 and is fully compatible with the ISA Bus The PC 104 interface is able to adapt the off the shelf PC 104 modules such as sound module fax modem module multi I O module and etc J1 PC 104 Bus Pin Assignment Pin rs so fs fev 7 sos e roo Pe soe 0 fav ar 2 or SAIS am afre sm 60 osc _ J2 PC 104 Bus Pin Assignments Ps fos e ims 7 fro fe jum Pe pron ao var Jumpers and Connectors 31 SBC84600 All in One CPU Board Series User s Manual 3 4 18 Serial Port Interface 3 4 18 1 COM Port Connector COM1 The connector COM 1 is a DB 9 connector and the following table shows the pin assignments of this connector Pin Signal Name 1 DCD Data carrier detect com a E 6 T DSR Data setreay e TOS garang 9 RI Ringindicator 3 4 18 2 COM Port Connectors COM2 COM3 COM4 The RS 232 pin
19. 3 1 Watchdog Timer Trigger Mode Setting JP1 10 3 3 2 Power Selection of Flat Panel Connector VDDM of LCD1 add RIE aota 10 3 3 3 CMOS Clear Jumper JP3 10 3 3 4 COM2 RS232 422 485 Settings JP4 JP5 JP6 11 3 3 5 Power Supply Type Selection JP7 11 3 3 6 COM2 Signal 5V Selection JP8 11 3 3 7 COM1 Signal 5V Selection JP9 11 3 3 8 COM4 Signal 5V Selection JP10 12 3 3 9 COM3 Signal 5V Selection JP11 12 3 3 10 Compact Flash Voltage Selection JP12 12 3 4 Connectors 20 ennnnennnnennenennnee 13 3 4 1 Enhanced IDE Interface Connector CNT 14 3 4 2 Flat Panel Bezel Connector CN3 15 3 4 3 VGA Flat Panel Connector VGA1 CN2 CN4 16 3 4 4 CPU Fan Connector CN5 22 3 4 5 Parallel Port CN7 23 3 4 6 Digital I O Port DIO1 CN8 24 3 4 7 ATX Power On Off Button CN9 25 3 4 8 Power Input Connector CN10 25 3 4 9 IrDA Connector CN11 26 3 4 10 AC97 Interface Link Connector
20. MS DOS environments The system performance depends on the installed CPU on the board 4 2 BIOS The system BIOS used in SBC84600VE is Award Plug and Play BIOS The SBC84600VE contains a single 4M bit Flash EPROM 4 3 Real Time Clock and CMOS RAM The SBC84600VE contains VT82C686B Integrated Real Time Clock RTC and 128 bytes of CMOS RAM The CMOS RAM stores the system configuration information entered via the SETUP program A battery with power lasting 10 years keeps the stored information on the RTC and CMOS RAM active when system power is turned off 4 4 System Memory SBC84600VE has one onboard 144 pin SODIMM socket that supports 16MB 32MB 64MB 128MB 256MB and up to 512MB SODIMM modules Hardware Description 35 SBC84600 All in One CPU Board Series User s Manual 4 5 VGA Interface The Twister T integrates S3 Graphics 128 bit ProSavage4 graphics accelerator into a single chip TwisterT brings mainstream graphics performance to the Value PC with leading edge 2D 3D and DVD video acceleration into a cost effective package Based on its capabilities Twister T is an ideal solution for the consumer corporateration users and entry level professionals The industry s first integrated AGP 4X solution TwisterT combines AGP 4X performance with Microsoft Direct X texture compression and assive 2Kx2K textures to deliver unprecedented 3D High Performance 3D Accelerator 128 bit 2D Graphics Engine DVD Playback and Video o
21. SBC84600VE 3 5 HDD Form Factor All in One CPU Board User s Manual Disclaimers The information in this manual has been carefully checked and is believed to be accurate AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document AXIOMTEK makes no commitment to update or to keep current the information contained in this manual AXIOMTEK reserves the right to make improvements to this document and or product at any time and without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2003 by AXIOMTEK Co Ltd All rights reserved July 2003 Version A2 Printed in Taiwan ESD Precautions Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions R Do not remove boards or integrated circuits from their anti static packaging until you are ready to install them E Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This helps to discharge any static electricity on your body
22. Save amp Exit Setup Abandon all Datas Award BIOS Utility 67 SBC84600 All in One CPU Board Series User s Manual This page does not contain any information 68 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual AppendixA Watchdog Timer Using the Watchdog Function The SBC84600VE CPU Board uses version 2 0 of the watchdog timer This onboard WDT generates either a system reset or non maskable interrupt NMI depending on the settings made on jumper JP1 of SBC84600VE Follow the steps below to enable and program the watchdog function of SBC84600VE Start 4 Un Lock WDT 4 Set multiple 1 4 4 Set base timer 0 F 4 WDT counting 4 re set timer 4 IF No re set timer 4 IF to disable WDT Watchdog Timer OUT 120H OAH enter WDT function OUT 120H 0BH enable WDT function OUT 120 ONH N 1 2 3 or 4 OUT 121 OMH M 0 1 2 F OUT 121 OMH M 0 1 2 F WDT time out generate RESET or NMI OUT 120 00H Can be disable at any time 69 SBC84600 All in One CPU Board Series User s Manual 70 Watchdog Timer
23. There will be no warning message displayed if the drive installed is 360K Boot Up NumLock Status This option enables and disables the numberlock function of the keypad The default value is On Qn Keypad functions confine with numbers CH Keypad functions convert to special functions i e left right arrow keys Gate A20 Option The default value is Fast The A20 signal is controlled by keyboard controller or chipset hardware Default Fast The A20 signal is controlled by Port 92 or chipset specific Fast method 6 Typematic Rate Setting This determines the typematic rate of the keyboard The default value is Disabled Enabled Enable typematic rate and typematic delay programming Disable typematic rate and typematic delay programming The system Disabled BIOS will use default value of these 2 items and the default is controlled by keyboard Award BIOS Utility 47 SBC84600 All in One CPU Board Series User s Manual Typematic Rate Chars Sec This option refers to the number of characters the keyboard can type per second The default value is 6 6 6characters persecond 8 Bcharacters persecond Typematic Delay Msec This option sets the display time interval from the first to the second character when holding a key The default value is 250 250 500 750 Security Option This item limits the access to the system and Setup or just to Setup T
24. Uninterrupted Power System UPS or to perform the store security control The digital I O is controlled via software programming Digital I O Connector CN8 Pin Signal Pin Signal DIO Out 0 2 DIO In 0 DIO In 1 20 ee 19 Dooi 6 TE E 00003 8 DIOIn3 i Dond 1 DIO In E 3 Pleu 3 4 6 1 Digital I O Software Programming The Digital I O on the board is not an isolated type Output Address Bit Output Address Bit Out 0 123h 0 In 0 123h 0 Out 1 123h 1 In 1 123h 1 Out 2 123h 2 In 2 123h 2 Out 3 123h 3 In 3 123h 3 Out 4 123h 4 In 4 123h 4 Out 5 123h 5 In 5 123h 5 Out 6 123h 6 In 6 1233h 6 Out 7 123h 7 In 7 123h 7 Example program Out 123h 03h Out 0 Out 1 Turn On Out 2 Out 3 Turn Off Out 123h OAh Out 0 Out 2 Turn Off Out 1 Out 3 Turn On 24 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual Example program If INPUT 123 is 1011 then INPUT 2 is 0 If INPUT 123 is 1100 then INPUT 0 amp 1 are 0 The INPUT signal has to be TTL signal 3 4 7 ATX Power On Off Button CN9 This 2 pin connector CN9 connects the ATX power button of the front panel to the Board allowing user to control the power on off state of the ATX power supply This jumper is only useful when installing an ATX power supply OO OOO OOS 00 3TH LR P Lo LA Jumpers and Connectors 25 SBC84600 All in One CPU Board Series User s Manual 3 4 9 IrDA Connector CN11 CN11 is a
25. ach system interrupt a type depending on the type of device using the interrupt DMA Resources When resources are controlled manually assign each system DMA channel as one of the following types depending on the type of device using the interrupt Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific DMA channel 2 PCI ISA PnP Devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture The default value is PCINSA PnP PCI VGA Palette Snoop Leave this field at Disabled The choice Enabled Disabled Assign IRQ For USB VGA This item is to enable or disable the IRQ assignment for USB VGA The options available are Enabled Disabled 60 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 7 PC Health Status This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value Phoenix AwardBIOS CMOS Setup Utility PC Health Status Current CPU Fan Current System Fan Vcore 2 5V 3 3V 5V 12V gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Current CPU Temp Show the current CPU temperature Current System Temp Show the current system temperature 2 5V 3 3V 5V Show the voltage of 2 5V 3 3V 5V
26. board and the USB will be used Even when equipped if a higher performance controller is added this feature should be disabled The choice Enabled Disabled Award BIOS Utility 51 SBC84600 All in One CPU Board Series User s Manual USB Keyboard Support Select Enabled if the system contains a Universal Serial Bus USB controller and you have a USB keyboard The choice Enabled Disabled CPU to PCI Write Buffer When this field is Enabled writes from the CPU to the PCI bus are buffered to compensate for the speed differences between the CPU and the PCI bus When Disabled the writes are not buffered and the CPU must wait until the write is complete before starting another write cycle PCI Dynamic Bursting This item is to enable disable the PCI dynamic bursting function PCI Master 0 WS Write When Enabled writes to the PCI bus are executed with zero wait states PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The default setting is Disabled PCI 2 Access 1 Retry When Disabled PCI 2 will not be disconnected until access finishes default When Enabled PCI 2 will be disconnected if max retries are attempted without success AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wa
27. changes with Setup the Award BIOS via its built in override feature resets your system to the CMOS default settings Avoid making any changes to the chipset defaults are strongly recommanded These defaults have been carefully chosen by both Award and the system manufacturer to provide the absolute maximum performance and reliability 40 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 1 Standard CMOS Setup Standard CMOS Setup is used to record some basic hardware configurations in the computer system and set the system clock and error handling If the motherboard is already installed in a working system there is no need to enter this option However the Standard CMOS option has to be setup in any of the following situations the system hardware configurations are changed the onboard battery fails and the configuration stored in the CMOS memory is lost or damaged Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Wed Aug 7 2002 Item Help Time hh mm ss 13 9 11 Menu Level K gt IDE Primary Master None gt IDE Primary Slave None Change the K IDE Secondary Master None Day month K IDE Secondary Slave None Year and Century Drive A 1 44M 3 5 in LCD Type T9 800x600 TFT Screen Expansion Enable TV Type NTSC Display Type During Post VGA Default Display Type After Post VGA Default Halt on All But keyboard Base Memory 640K Extended Memory 65535K
28. d Connectors SBC84600 All in One CPU Board Series User s Manual ENAVDD ENAVDD ENAVDD ENABLK ENABLK ENABLK Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 2 P oja CD re oO NIN 3 x AJAJ ao oa 22 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 4 5 Parallel Port CN7 The SBC84600VE has a multi mode parallel port CN7 to support Standard mode IBM PC XT PC AT and PS 2 compatible with bi directional parallel port Enhanced mode Enhance parallel port EPP compatible with EPP 1 7 and EPP 1 9 IEEE 1284 compliant High speed mode Microsoft and Hewlett Packard extended capabilities port ECP IEEE 1284 compliant The address select of the onboard parallel port in LPT1 3BCH or disabled is done by BIOS CMOS setup Description Pin Description Strobe 14 Auto Form Feed Data 1 Initializedt Data 2 Printer Select In Data 3 Acknowledge Busy Paper Empty gO D D D D D D D D D D D D D D oda D 0 D 0 D 0 oda Jumpers and Connectors 23 SBC84600 All in One CPU Board Series User s Manual 3 4 6 Digital I O Port DIO1 CNS The board is equipped with an 8 channel digital I O connector CN8 that meets a system customary automation control needs The digital I O can be configured to control the cash drawer or to sense the warning signal of an
29. est This option speeds up Power On Self Test POST after turning on the system power If it is set as Enabled BIOS will shorten or skip some check items during POST The default setting is Enabled Enable Quick POST Normal POST First Second Third Boot Device These items allow the selection of the 1 27 and 3 devices that the system will search for during its boot up sequence The wide range of selection includes Floppy LS120 ZIP100 HDDO 3 SCSI and CDROM Boot Other Device This item allows the user to enable disable the boot device not listed on the First Second Third boot devices option above The default setting is Enabled 46 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual Swap Floppy Drive This allows you to determine whether to enable Swap Floppy Drive or not When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek During POST BIOS will determine the floppy disk drive type 40 or 80 tracks 360Kb type is 40 tracks while 720Kb 1 2MB and 1 44MB are all 80 tracks The default value is Enabled BIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Note Enabled that BIOS can not tell from 720K 1 2M or 1 44M drive type as they are all 80 tracks Disabled BIOS will not search for the type of floppy disk drive by track number
30. ets ACPI function with its built in power management feature Designed for the professional embedded developers this SBC84600VE is virtually an ultimate one step solution to various applications It provides fanless possibility for critical application environmemts with low power consumption design to improve system MTBF Introduction 1 SBC84600 All in One CPU Board Series User s Manual 1 2 Specifications Processor B VIA EDEN 400MHz 667MHZ or C3 800MHz C3 1GHz CPU or other frequency processors are manufacturer optional L2 Cache B Integrated in CPU Chipset B VT8606 Twister T VT82C686B System Memory B One 144 pin DIMM socket B Maximum up to 512MB SDRAM BIOS B AWARD BIOS Plug and Play 4Mbit Flash ROM with SmartView VGA BIOS Function and integrated Ethernet Novell RPL and Windows PXE Boot ROM functions Watchdog Timer RB Generates a system reset or NMI by jumper selectable E Software programmable time interval E 64 levels 0 5 8 5 80 50 800 100 1600 seconds Standard I O B Four serial ports including three RS 232 and one RS 232 422 485 One parallel port SPP EPP ECP One HDD Interface One FDD Interface One PS 2 Keyboard amp Mouse Interface One IrDA interface for wireless communication USB Interface 2 USB ports with USB Spec Rev 1 1a compliant Ethernet B Realtek 8139C PCI Bus 10 100M Base T B Wake On LAN via ATX power supply B Onboard RJ 45 connector Digital I O 8 channel TTL DTL compatible
31. he default value is Setup The system will not boot and access to Setup will be denied if the incorrect System password is entered at the prompt The system will boot but access to Setup will be denied if the correct password Setup is not entered at the prompt NOTE To disable security select PASSWORD SETTING at Main Menu and then password is asked to enter Do not type anything just press lt Enter gt and it will disable security Once the security is disabled the system will boot and you can enter Setup freely OS Select for DRAM gt 64MB This segment is specifically created for OS 2 when DRAM is larger than 64MB If the operating system is OS 2 and DRAM used is larger the 64MB OS 2 has to be selected otherwise under non OS2 default is NON OS2 48 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 6 Video BIOS Shadow Video shadowing increases the video speed by copying the video BIOS into RAM However it is still optional depending on the chipset design The default value of this option is Enabled Enabled Video BIOS shadowing is enabled Disabled Video BIOS shadowing is disabled C8000 CBFFF Shadow DCO000 DFFFF Shadow Shadowing ROM reduces available memory between 640KB and 1024KB These fields determine whether optional ROM is copied to RAM or not Award BIOS Utility 49 SBC84600 All in One CPU Board Series User s Manual 5 2 3 Advanced Ch
32. ing Setup Award BIOS Utility 65 SBC84600 All in One CPU Board Series User s Manual 5 2 12 Save amp Exit Setup This is to determine whether or not to accept the modifications Typing Y quits the setup utility and saves all changes into the CMOS memory Typing N brigs back to Setup utility Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password pater Men SAVE to CMOS and EXIT Y N Y PnP PCI Con PC Health Status Exit Without Saving Esc Quit 4 Vv gt Select Item F10 Save amp Exit Setup Save Data to CMOS 66 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 13 Exit Without Saving Select this option to exit the Setup utility without saving the changes made in this session Typing Y will quit the Setup utility without saving the modifications Typing N will return to Setup utility Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power M SAS ean Quit Without Saving Y N N PnP PCI Con PC Health Status Exit Without Saving Esc Quit M YV gt Select Item F10
33. input and output Board ID Dallas DS2401 Board unique ID support Solid State Disk Interface Introduction SBC84600 All in One CPU Board Series User s Manual B One CompactFlash Type II Socket Expansion Slot one 16 bit pc 104 connector AC97 Link AC97 Link intelface for external audio Cedoec Kit AX93100 Drivers VIA Chipset Driver 6 Ethernet Utility and Drivers VGA Drivers Introduction 3 SBC84600 All in One CPU Board Series User s Manual This page does not contain any information 4 Introduction SBC84600 All in One CPU Board Series User s Manual Chapter 2 Installation 2 1 Installation Steps Follow the steps listed below to install the SBC84600VE in the system 1 Make sure the power is OFF 2 Set the configuration jumpers according to the jumper settings in Chapter 3 3 Connect the I O cables and peripherals i e floppy disk hard disk monitor keyboard power supply and etc to the CPU board NOTE The color of pin one is usually red or blue while others are gray 2 2 Peripherals for a Minimum System The followings is a list of typical peripherals required to build a minmum system AT or ATX Power supply e IBM PS 2 keyboard And Mouse Display monitor Floppy or hard disk with MS DOS or Flash Disk emulator Installation 5 SBC84600 All in One CPU Board Series User s Manual This page does not contain any information 6 Installation SBC84600 All in One CPU B
34. ipset Features Since the features in this section are related to the chipset on the CPU board and are completely optimized changing the default settings in this setup table are not recommended unless the user is well oriented with the chipset features Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing By SPD Enabled Item Help X DRAM Clock Host CLK X SDRAM Cycle Length 3 Menu Level K X Bank Interleave Disabled Memory Hole Disabled P2C C2P Concurrency Enabled System BIOS Cacheable Disabled Video RAM Cacheable Disabled Frame Buffer Size 16M AGP Aperture Size 64M AGP 4X Mode Enabled AGP Driving Control Auto AGP Driving Value DA OnChip USB Enabled USB Keyboard Support Disabled OnChip Sound Auto OnChip Modem Disabled CPU to PCI Write Buffer Enabled PCI Dynamic Bursting Enabled PCI Master 0 WS Write Enabled PCI Delay Transaction Disabled PCl 2 Access 1 Retry Enabled AGP Master 1 WS Write Disabled AGP Master 1 WS Read Disabled gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults DRAM Timing By SPD This item is selected depending on whether the board has paged DRAMs or EDO extended data output DRAMs 50 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual DRAM Clock The DRAM clock value is set depending on whether the board has paged DRAMs
35. isk error it will stop for all other errors 44 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 2 Advanced BIOS Features This section is used to configure and improve the system and set up some system features according to the user s preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features Virus Warning Disabled Item Help CPU Internal Cache Enabled External Cache Enabled Menu Level K CPU L2 Cache ECC Checking Enabled Processor Number Feature Enabled Allows you to Quick Power On Self Test Enabled choose the VIRUS First Boot Device HDD 0 warning feature Second Boot Device Floppy for IDE Hard disk Third Boot Device LS120 boot sector Boot Other Device Enabled protection If this Swap Floppy Drive Disabled function is enable Boot Up Floppy Seek Enabled and someone Boot Up NumLock Status On attempts to write Gate A20 Option Fast data into this area Typematic Rate Setting Disabled BIOS will show Typematic Rate Chars Sec 6 a warning Typematic Delay Msec 250 message on Security Option Setup screen and alarm OS Select For DRAM gt 64MB Non OS2 beep Video BIOS Shadow Enabled C8000 CBFFF Shadow Disabled CC000 CFFFF Shadow Disabled D0000 D3FFF Shadow Disabled D4000 D7FFF Shadow Disabled D8000 DBFFF Shadow Disabled DC000 DFFFF Shadow Disabled Small Logo EPA Show Disabled A gt E Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5
36. it states AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states 52 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 4 Integrated Peripherals This option sets the hard disk configuration mode and port Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Channeld Enabled Item Help OnChip IDE Channel Enabled IDE Prefetch Mode Enabled Menu Level K Primary Master PIO Auto Primary Slave PIO Auto Secondary Master PIO Auto Secondary Slave PIO Auto Primary Master UDMA Auto Primary Slave UDMA Auto Secondary Master UDMA Auto Secondary Slave UDMA Auto Init Display First PCI Slot IDE HDD Block Mode Enabled Onboard FDD Controller Enabled Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 UART 2 Mode Standard IR Function Duplex Half TX RX inverting enable No Yes Onboard Parallel Port 378 IRQ7 Onboard Parallel Mode Normal X ECP Mode Use DMA 3 X Parallel Port EPP Type EPP1 9 Onboard Legacy Audio Disabled X Sound Blaster Disabled X SB I O Base Address 220H X SB IRQ Select IRQ5 X SB DMA Select DMA 1 X MPU 401 Disabled X MPU 401 I O Address 330 333H gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults On Chip IDE Channel0 Channel1 The integrated peripheral controller contains an IDE
37. mized Defaults Integrated Peripherals Set Supervisor Password Power M lais Load Fail Safe Defaults Y N N PnP PCI C PC Health Status Exit Without Saving Esc Quit M V gt Select Item F10 Save amp Exit Setup Load Fail Safe Defaults To load BIOS defaults value to CMOS SRAM enter Y If not enter N Award BIOS Utility 63 SBC84600 All in One CPU Board Series User s Manual 5 2 10 Load Optimized Defaults This option is to load the default values to the system configuration These default settings are optimal and enable all high performance features Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password P M ower Man Load Optimized Defaults Y N N PnP PCI Co PC Health Status Exit Without Saving Esc Quit A Vv gt Select Item F10 Save amp Exit Setup Load Optimized Defaults To load SETUP defaults value to CMOS SRAM enter Y If not enter N 64 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 11 Set Supervisor User Password Either supervisor or user password or both of them can be set in this option The differences between them are 1 supervisor password can enter and change the options of the setup menus 2 user passwo
38. nction used only The choice NA 3 4 5 7 9 10 11 Award BIOS Utility 57 SBC84600 All in One CPU Board Series User s Manual e Soft off by PWRBTN This only works with the system using an ATX power supply It also allows user to define the type of soft power OFF sequence for the system to follow This option follows the conventional manner systems perform when power is turned OFF Instant Off is a soft power OFF sequence requiring only the switching of the power supply button to OFF Instant Off default Upon turning OFF system from the power switch this option will delay the complete system power OFF sequence by approximately 4 seconds Within this delay period system will temporarily enter into Suspend Mode enabling you to restart the system at once Delay 4 Sec Wake Up Events An input signal on the network 2 awakens the system from a soft off state 58 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual 5 2 6 PNP PCI Configuration This section describes the PCI bus system configuration PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make changes to the default settings Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations
39. nferencing LCD and Flat Panel Monitor Support High Screen Resolution CRT Support 36 Hardware Description SBC84600 All in One CPU Board Series User s Manual 4 6 lO Port Address Map The CPU card communicates via I O ports It has a total of 1KB port addresses that can be assigned to other devices via I O expansion cards Address Devices 000 01F DMA controller 1 020 03F 040 05F 060 06F 070 07F 080 09F 0A0 0BF OFO Clear math coprocessor busy signal 0C0 ODF DMA controller 2 OF1 Reset math coprocessor OF8 OFF 120 Interrupt controller 1 Timer Keyboard controller Real time clock NMI DMA page register Interrupt controller 2 Math processor Disable watchdog timer operation read Enable watchdog timer operation read Watchdog Fixed disk controller 122 1F0 1F8 200 207 300 31F 360 36F 378 37F 3B0 3BF 3C0 3CF 3D0 3DF CGA card 3F0 3F7 Floppy disk controller 3F8 3FF Serial port 1 COM1 2F8 2FF Serial port 2 COM 3E8 3EF Serial port 3 COM3 2E8 2EF Serial port 4 COM4 Game port Prototype card Reserved Parallel port 1 MDA video card including LPT EGA card N N Slo Hardware Description 3 SBC84600 All in One CPU Board Series User s Manual 4 7 Interrupt Controller The SBC84600VE is a fully PC compatible control board It consists of 16 ISA interrupt request lines and 4 of the 16 can be either ISA or PCI The mapping list of the 16 interrupt re
40. nsity drive 1 2MB capacity 720K 3 5 in 3 5 inch double sided drive 720Kb capacity 1 44M 3 5 in 3 5 inch double sided drive 1 44MB capacity 2 88M 3 5 in 3 5 inch double sided drive 2 88MB capacity Select Display Device This item selection includes Auto CRT LCD and CRT LCD LCD Type This item selection includes TO 640x480 TFT T1 800x600 TFT T2 1024x768 TFT T3 1280x1024 TFT T4 640x480 DSTN T5 800x600 DSTN T6 1024x768 DSTN T7 1024x768 TFT T8 640x480 TFT T9 800x600 TFT T10 1024x768 TFT T11 1280x1024 TFT T12 1400x1050 DSTN T13 800x600 DSTN T14 1024x768 DSTN T15 1280x1024 DSTN Display Type During Post This item selection includes VGA DEFAULT CRT LCD CRT LCD TV and CRT TV Display Type After Post This item selection includes VGA DEFAULT CRT LCD CRT LCD TV and CRT TV Award BIOS Utility 43 SBC84600 All in One CPU Board Series User s Manual Halt On This field determines whether the system will halt if an error is detected during power up The system boot will halt on any error detected No errors default Whenever the BIOS detects a non fatal error All errors S R the system will stop and you will be prompted All But Keyboard The system boot will not stop for a keyboard error it will stop for all other errors The system boot will not stop for a keyboard or All But DiskiKey disk error it will stop for all other errors All But Diskette The system boot will not stop for a d
41. oard Series User s Manual 3 1 Chapter 3 Jumpers and Connectors Jumpers and Connectors Layout CN8 COM2 COM3 COM4 JP8 JP9 USR USB2 CN2 VIDEO1 CN14 N13 LAN1 CN1 CN12 VGA1 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 2 Jumpers and Connectors Dimensions 104 EH 100 86 T III pensaa J o IIT T T arya 98 04 T aa 19837 96 347 x Pea red I I LC LGT a SI P apt 8 89 i 5 16 Sal po a MEJA a a 152 6 8 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual 3 3 Jumper Settings Making the proper jumper settings configure the SBC84600VE to match the needs of your application The following table shows the default jumper settings for the onboard devices C aer Face Troe Danes T aa eee Jumpers and Connectors 9 SBC84600 All in One CPU Board Series User s Manual 3 3 1 Watchdog Timer Trigger Mode Setting JP1 The watchdog timer is an indispensable feature of the SBC84600VE It has a sensitive error detection function and a report function When the CPU processing comes to a halt the watchdog either generates a NMI or resets the CPU Options Setting NMI Short 1 2 RESET Short 2 3 Disabled default Open 3 3 2 Power Selection of Flat Panel Connector VDDM of LCD1 and LCD
42. onfiguration of the VGA interface is done via the software utility and no jumper setting is required The following two tables are the pin assignments for the CRT VGA connector and the flat panel connector VGA1 CRT VGA Connector Pin Assignment fin Descipion in Description Pin Tans Pi res 2 Gren a me a m s w s w z w s w o m CN2 Flat Panel Connector Pin Assignment R Description Pin Tea Pin Haas Pa eno s wm 6 ow r me s ow Jo o m Ja s Jes e o m o e e e sp e fop m fa e a vw Je e l s ww a ww 16 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual CN4 Flat Panel Connector for XVGA Name Description PO P35 Flat panel data output Jumpers and Connectors 17 SBC84600 All in One CPU Board Series User s Manual 3 4 3 2 Flat Panel Interface Pins for Color DSTN and Color TET LCD Twister T VT8606 a H H 9 sok x x H o o o f eo w R H E E e wo oo o et o a es er et et e e H 7 HTH Cafe lela e ee e e e w ss Cm Js a ee ee o ea a pews OP 18 Jumpers and Connectors SBC84600 All in One CPU Board Series User s Manual LP LP LP Jumpers and Connectors 19 SBC84600 All in One CPU Board Series User s Manual 2X15 bit LP LP LP HSYNC Hlwloymsyrm o B Hlwlopyrmsyrm o A 20 Jumpers an
43. our hardware and software both support one of the other available modes The choice SPP EPP ECP ECP EPP ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode The choice 3 1 Award BIOS Utility 55 SBC84600 All in One CPU Board Series User s Manual 5 2 5 Power Management Setup The Power Management Setup is to save energy of the system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Disabled Item Help Power Management Press Enter ACPI Suspend Type 1 POS Menu Level K PM Control by APM Yes Video Off Option Suspend gt Off Video Off Method V H SYNC Blank MODEM Use IRQ 3 Soft Off by PWRBTN Instant Off Wake Up Events Press Enter A gt E Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults 6 ACPI Function This item is to enable disable the Advanced Configuration and Power Interface ACPI The choice Enabled Disabled Power Management This item is to select the Power Management mode The choice User Define Min Saving Max Saving ACPI Suspend Type This item is to select the APCI suspend type S1 POS gt Power On Suspend S3 STR gt Suspend To DRAM The choice S1 POS S3 STR 56 Award BIOS Utility SBC84600 All in One
44. quest lines is shown below NMI Parity check error IRQO System timer output ras Repay aes Pinas Reeves oooO 38 Hardware Description SBC84600 All in One CPU Board Series User s Manual Chapter 5 Award BIOS Utility Chapter 5 describes the different settings available in the Award BIOS that comes with the SBC84600VE CPU card Also the instructions on how to set up the BIOS configuration are contained in this chapter 5 1 BIOS Introduction The Award BIOS Basic Input Output System installed in the system ROM supports Intel Celeron processors in a standard IBM AT compatible I O system The BIOS provides critical low level support for standard devices such as disk drives serial and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system 5 2 BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When the computer is turned ON the Award BIOS is immediately activated The following message will appear on the screen Press lt DEL gt to Enter Setup Then press the lt Del gt key immediately to enter the Setup utility The delay of pressing the lt Del gt key will cause POST Power On Self Test to continue with the test routines thus preventing invoking the Setup In this case the system has to be re
45. rd just can enter but do not have the right to change the options of the setup menus When this function is selected the following message will appear at the center of the screen for creating a password ENTER PASSWORD Type the password with eight characters at most and press lt Enter gt The password typed will now clear any previously entered password from CMOS memory Then confirm the password by typing the password again and pressing lt Enter gt Or not enter a password and abort the selection by pressing lt Esc gt To disable the password by pressing lt Enter gt without typing in any password when the message Enter Password is showed Then message below will appear to confirm that the password has been disabled PASSWORD DISABLED Once the password is disabled the system will boot and enter Setup freely When a password is enabled it has to be typed to enter the Setup every time This prevents any unauthorized person from changing the system configuration Additionally when a password is enabled the BIOS can also set to request a password every time the system reboots This would prevent unauthorized use of the computer The user can determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password is required during boot up and entry into Setup If it set as Setup prompting will only occur prior to enter
46. re predefined Type User is user definable Press lt PgUp gt lt gt or lt PgDn gt lt gt to select a numbered hard disk type or type the number and press lt Enter gt Note that the specifications of the drive in the system must match with the drive table The hard disk will not work properly if the improper information within this category is entered If the disk drive type does not match or is not listed the Type User is used to define the drive type manually If the Type User is selected related information has to be entered Enter the information directly from the keyboard and press lt Enter gt This information should be provided in the documentation from the hard disk vendor or the system manufacturer If the controller of HDD interface is ESDI select Type 1 If the controller of HDD interface is SCSI select None If the controller of HDD interface is CD ROM select None CYLS number of cylinders LANDZONE HEADS number of heads SECTORS number of sectors PRECOMP MODE HDD access mode If there is no hard disk drive installed select NONE and press lt Enter gt 42 Award BIOS Utility SBC84600 All in One CPU Board Series User s Manual Drive A type Drive B type The category identifies the types of floppy disk drive A or drive B installed in the computer No floppy drive installed 360K 5 25 in 5 25 inch PC type standard drive 360Kb capacity 1 2M 5 25 in 5 25 inch AT type high de
47. started for entering the BIO setup by pressing the Reset button or simultaneously pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys Besides turning the system OFF first and then ON again can also restart the system When entering the Setup utility the Main Menu screen will appear on the screen Various setup functions and exit choices can be selected from this menu In general the arrow keys are used to highlight items lt Enter gt to select the lt PgUp gt and lt PgDn gt keys to change entries lt F1 gt for help and lt Esc gt to quit Award BIOS Utility 39 SBC84600 All in One CPU Board Series User s Manual Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving Esc Quit F9 Menu in BIOS AV gt lt Select Item F10 Save amp Exit Setup Time Date Hard Disk Type The section below the setup items in the Main Menu displays the control keys for this menu Another section located at the bottom of the Main Menu just below the control keys section displays information on the currently highlighted item in the list NOTE If the computer cannot boot after making and saving system
Download Pdf Manuals
Related Search