RT08G_2011 v_2.1 ANG TITANIUM.cdr
Contents
1. No NAME RANGE DEFAULT SETTING FUNCTION 20 FIREPLACE 45 85 C 55 C Preset temperature of the fireplace kept by the control Temp unit 31 Switch on Temp 30 60 C 50 C Minimal temperature of the fireplace at which of PUMPS the CH pump P3 and P1 WAW can be activated 41 Maximum temp 30 99 C 60 C Maximal temperature of the WAW accumulator of WAW The exceeding turns off the loading pump 42 Minimum temp 30 99 C 50 C Minimal temperature of WAW accumulator of WAW The exceeding turns on the loading pump 43 Loading temp 30 99 C 65 C Preset temperature of the fireplace automatically set at of WAW special the loading of the WAW accumulator in the priority mod WAW MODE SPECIAL 44 Delta Temp 1 10 C 2 C Minimal difference between fireplace and WAW accumulator of WAW temperature needed for the WA W pump operation P1 10 Signal OFF ON ON OFF turns off sound signal ON ALARM ON turns on sound signal ALARM ON ALARM turns on sound and alarm 11 Polish Polish i i Language English Selection of the language version Deutsch OFF backlight is active for 2mins from the last pressin ILCD backlight OFF ON OFF lof the button ION backlight is active when the control unit is switched on PARAMETERS LEVEL 2 No NAME RANGE DEFAULT SETTING FUNCTION Mine Sones OFF IOFF time zo2. A USER CAN BE THE CAUSE OF SAFETY CONDITIONS DETERIORATION AND CAN EXPOSE THE USER TO ELECTRIC SHOCK OR DAMAGE DEVICES SUPPLIED WARNING 1 Producer does not take the responsibility for damage caused by atmospheric discharge 2 and overvoltage in the mains 3 Burnt fuses are not subject to warranty replacement Date of sale Seller s signature and stamp ARGO FILM Recycling Plant No 6 180 Krakowska st 52 015 Wroclaw Register No GIOS E 0002240WZ Worn out electronic the utilization collection place where will 0 515 122 142 be accepted for free and electric devices must be transfered to Ph 071 794 43 01 bs INIA X K C Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 tax index number 899 020 21 48 Bank account BZ WBK S A O WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl E mail tatarek tatarek com pl 1 Demonstration change of the lt 21 gt ALARM Temp parameter defining the fireplace temperature so that after exceeding it the alarm sound is generated Parameters Level 3 Press Repeatedly the button 7 till the Parameters level 0 parameter setting screen appears Button 6 K gt 0 blinks 3 times the button 4 gt 3 blinks Button 6 OK gt 3 stops blinking the Parameters Level 3 has been chosen Button 7 O gt current valu
3. ATAREK has initiated management system and complies with the following standard 1SO9001 2000 CERTIFICATE No 133 2004 of 01 2004 Polish Foreign Trade Chamber The last two digits of the year in which the CE marking was affixed 07 Place of issue Manufacturer representative Wroclaw Mirostaw Z asena Las Date otissue Posion Fig lc Operation configuration of the control unit with the heat exchanger 08 2007 Konstruktor for the CH and WAW systems WAW Warm Applicable Water accumulator boiler FIREPLACE Water jacket fireplace CH Central heating system Tl Upper temperature sensor of the WAW accumulator option T2 Lower temperature sensor of the WAW accumulator T3 Temperature sensor of the fireplace water jacket P1 Pump loading WAW from fireplace P2 Pump of the primary side of heat exchanger it operates if P1 and P3 are activated P3 Circulating pump CH PP Electronically controlled choke valve of the fireplace 2 1 Choke valve operation The choke valve regulates an air supply to the combustion chamber which allows the temperature of the fireplace water jacket to be kept at the preset value The task is realized by comparing the temperature of the water jacket T3 and preset temperature the lt 20 gt FIREPLACE Temp parameter and then by gradual opening shutting the choke valve The shutdown of the regulator caused e g by power decline automatically causes thechoke valve to be set at the rest position defined by the lt 50 gt C
4. CLARATION Ref No 58 RT 01 2007 1 B We ZAKLAD ELEKTRONICZNY TATAREK Jerzy Tatarek 75 Swieradowska St 50 559 Wroclaw declare under our sole responsibility that the product Regulator of heating system with solar collector model RT 08 RT 08K RT 08P RT 08G is in conformity with the basic requirements included in Directive EMC 2004 108 WE of 15 12 2004 the electromagnetic compatibility law of 13 04 07 and Directive LVD 2006 95 WE of 21 08 07 Laws Journal of 2007 No 155 pos 1098 regarding the requirements for electric devices To the conformity evaluation the following harmonized standards were used CH Central Heating WAW Warm Applicable Water PN EN 60730 2 1 2002 Automatic electric regulators for house usage and the like Part 2 1 PERE Specific SRE regarding electric cain for electric house Fig 1b Operation configuration of the control unit with the heat exchanger for the CH system devices pump of the heat exchanger and the CH system connected to the P3 output PN EN 60730 1 2002 Automatic electric regulators for house usage and the like Part 1 General requirements PN EN 55022 2000 Electromagnetic compatibility EMC IT devices Characteristics of radioelectric noises Acceptable levels and measurement methods Complementary information Laboratory IASE 51 618 Wroclaw 1 Wystawowa st Test report No 39 DL 1 07 of 22 06 2007 41 DL 1 07 of 03 07 2007 FIREPLACE Electronic Engineering Plant T
5. TIES OF THE FIREPLACE AND CENTRAL HEATING SYSTEM THEIR CHANGE OUGHT TO BE CONSULTED WITH THE FIREPLACE PRODUCER ILL CONSIDERED MODIFICATIONS CAN CAUSE UNSTABLE AND INEFFICIENT OPERATION OF THE SYSTEM Screen of the fireplace operation shows the current temperature of the fireplace and the level of choke valve opening Current time Temperature of the water jacket of the fireplace T3 Time zone a ten a ae Operation mode Choke valve opening o the fireplace Preset temperature It s a stable state that is in order to change it you need to press the CHOOSE button 7 During appearing this screen you can change the preset temperature of the fireplace the lt 20 gt FIREPLACE Temp parameter After pressing the CONFIRM button 6 K the preset temperature blinks whose value can be altered with the buttons 4 or 5 To confirm the changes you need to press the CONFIRM button 6 Kk once more At the economic time zones e4 or e5 the displayed temperature is corrected by the drop the lt 22 gt ECO Temp parameter that is indicated by the minus sign instead of C During the loading of the WAW accumulator inthe WAW MODE SPECIAL mode the preset temperature gets automatically raised up to the lt 43 gt Loading temp of WAW special parameter value that is indicated by the plus s
6. WARNING WE INFORM THAT THE OFFERED CONTROL UNIT CAN BE ONLY APPLIED TO THE FITTING DEVICES THE REQUIREMENTS OF THE TECHNICAL AND BUILDING STANDARDS CONCERNING THE CORRECTNESS OF STOVE FITTER AND HEATING SYSTEMS HANDLING THE FIREPLACE INPUTS MUST BE MET WRONG USAGE OF THE CONTROL UNIT CAN LEAD BOTH TO ITS DAMAGE AND IN EXTREME CASES TO THE DAMAGE OF THE FIREPLACE INPUT AND HEATING SYSTEM CONTROLLED BY THE FIREPLACE AS WELL ALONG WITH THE DEVICES THAT COOPERATE WITH THE HEATING SYSTEM WNASS Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 Tax index number 899 020 21 48 Bank account BZ WBK S A WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl e mail tatarek tatarek com pl 20 WANA RT08G 2011 v 2 1 ANG TITANIUM Zak ad elektroniczny TATAREK Jerzy Tatarek USER MANUAL Program version 2 1 31 01 2011 RT 08G TATAREK CONTROL UNIT OF THE HEATING SYSTEM WITH A FIREPLACE CONTROLLED BY A CHOKE VALVE The RT 08G control unit controls the heating system based on the water jacket fireplace that is a heat source in which combustion process is controlled by a choke valve The heat receivers are Warm Applicable Water accumulator WAW and Central Heating system CH The control unit is equipped with its own emergency power source breaks in power supplying up to 8 secs do not interrupt its operation over the time th
7. active zone of higher number In the control unit there s a zones program In order to activate it you need to set the lt 14 gt Time zones parameter to ON fia ZONE 1 FROM 6 00 TO 8 00 ZONE 2 FROM 14 00 TO 17 30 ZONE 3 FROM 20 00 TO 22 30 ZONE e4 FROM 23 00 TO 5 30 ZONE e5 FROM 8 00 TO 13 30 The zones 1 3 relates to the pump loading the WAW accumulator in the mode CLOCK and Special see p 2 4 The zones e4 e5 enable lowering the preset temperature of the fireplace by the lt 22 gt ECO Temp parameter atthe limited demand for the heat 3 2 Screens Alarm screens ALARM is not seen till the following emergency situation takes place 1 Damage of the T1 sensor upper one of the WAW The WAW temp sensor T1 damaged text shows up The alarm doesn t work if the sensor is not installed 2 Damage of the T2 sensor lower one of the WAW The WAW temp sensor T2 damaged text shows up 3 Damage of the T3 sensor of the fireplace The Fplace temp sensor T3 damaged text shows up 4 The exceeding of the limit temperature of the fireplace defined by the lt 21 gt ALARM Temp parameter The too high temp of the fireplace text shows up Emergency situation is accompanied by a broken sound alarm that can be turned off by pressing the CONFIRM button 6 OK In the emergency of exceeding the temperature of the fireplace the CH pump turns on to cool off the fireplace PARAMETERS LEVEL 1
8. auses blinking of the parameter field to be changed By pressing 4 or 5 one can alter its value If there are more parameter fields on the screen e g setting the clock then one will go among them by pressing the CHOOSE button 7 By clicking the CONFIRM button 6 one confirms the changes the parameter field stops blinking The changed parameter not confirmed for 10 secs is not accepted by the control unit and it recalls a previous value of the parameter PARAMETERS LEVEL 4 No NAME RANGE DEFAULT FUNCTION 90 ProdNo 0 n 1 Number of the parameters set dependent on fireplace producer 91 RESET OFF ON OFF Setting the value of ON causes the recall of all parameters to their default pre sets and restarts the control unit 92 PASSWORD 0 9999 0000 0000 PASSWORD OFF PASSWORD ON 99 Service OFF OFF The ON value causes diagnostics screen to be added Screen ON for servicing Password The changes of important parameters are possible only at unlocked password To unlock the password you need to input proper sequence of digits with the buttons With the CHOOSE button 7 to change the digits position and CONFIRM button 6 OK to acknowledge all and finish the procedure of changing the password The unlocked password is set to 0000 Once again entering into the password change procedure causes a new pa
9. e emergency buffering power source is activated The control unit can cooperate with the TATAREK A 200WAC emergency power supply system which ensures that all the devices connected to the RTO8G control unit can operate without any disruption in case of power decline even up to 9 hrs 1 Basic technical parameters Power Power consumption without load Max connection power Operation conditions Housing protection class Fuse Number of outputs to control pumps Number of nonvoltage outputs Number of outputs to control the choke valve drive Number of water temperature sensors Temp measurement precision Temp measurement resolution Number of the time zones 230V 50Hz 5W 750W 0 50 C humidity 10 90 no condensation IP41 6 3A 250V 3 250W 230V 50Hz 1 1 5V 500mA DC 3 KTY81 0 100 C 2 C 0 5 C 4 2 Principle of Operation The main function of the control unit is to keep temperature in the water jacket at the preset value The task is realized by measuring temperature T3 and controlling the cold air choke valve PP properly Fireplace operation temperature is defined by the lt 20 gt FIREPLACE Temp parameter see PARAMETERS LEVEL 1 If the fireplace temperature T3 is higher than the lt 20 gt FIREPLACE Temp parameter the choke valve is gradually shut off limiting air supply and if the temperature T3 is lower than the lt 20 gt FIREPLACE Temp paramet
10. e of the lt 21 gt ALARM Temp parameter shows up Button 7 Kk gt current value you want to change starts blinking Buttons 4 and 5 and gt you set a new value Button 6 gt we confirm the new value Repeatedly the button 7 O till the parameter end setting screen appears 4 Installing the control unit THE REGULATOR IS SUPPLIED BY 230V S0HZ ANY MOVES REGARDING INSTALLATION SHOULD BE MADE AT THE DISCONNECTED MAINS THE REGULATOR HAS TO BE CONNECTED TO THE MAINS WITH THE ZERO PIN THE REGULATOR SHOULD NOT BE EXPOSED TO WATER AFFECTING ITS ENVIRONS OUGHT TO BE CLEAN THE PRODUCER DOESN T TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED BY WRONG USAGE OF THE REGULATOR Connection diagram of the elements of the control unit is presented on fig 3 PP O O Choke valve seo S mir Pm O e T2 Temperature uw 3 i sensors o ojejo V T3 LifL2jL3 L D ri LL 29 9 2 NIN NIN Ae 2 2 CONTROL Pump P1 L N MAINS 230V 50Hz La PF 230V 50Hz Pump P2 230V 50Hz Fig 3 Electrical scheme Pump P3 230V 50Hz PP Choke valve Tl Upper temperature sensor of the WAW accumulator option T2 Lower temperature sensor of the WAW accumulator T3 Temperature sensor of the fireplace water jacket P1 Pump loading the WAW accumulator from the fireplace P2 Pump of the primary side of t
11. er the choke valve is gradually opened up The second function is to control the WAW pump loading the warm applicable water accumulator WAW The WAW P1 pump operates if the fireplace temperature both exceeds the lt 31 gt Switch on Temp of PUMPS value andis higher than the WAW accumulator temperature T2 by the lt 44 gt Delta Temp of WAW parameter see PARAMETERS LEVEL 1 The third function is to control the circulating pump P3 of central heating system The pump works if the fireplace temperature exceeds the lt 31 gt Switch on Temp of PUMPS value It s possible to activate the WAW priority function PRIORITY see the description of operation modes of the WAW accumulator chapter 2 4 of the manual The control unit is also equipped with the CLOCK function to control the WAW priority and the fireplace operation temperature in selected times of day l The fireplace can also be equipped with warm air distribution system based on the RT 03C ARO control unit The control unit measures temperature in the chamber of the fireplace air ventilator and controls its rotation speed in manual or automatic mode Fig la Basic operation configuration of the control unit 2 Admission date Realization date Signature Remarks 7 f IINTASe PRODUCENT ZASILACZY SIECIOWYCH ISO 9001 2000 CE CONFORMITY DE
12. function of the buffer only ON Standard operation parallel operation of pumps without favouring the WAW circuit PRIORITY Faster reaching the readiness of the WAW accumulator by limiting heat obtain by the heating system The CH pump works cyclically Turning off the WAW pump after loading the accumulator causes the comeback of normal operation of the CH pump CLOCK beyond the time zones 1 3 the pump operates like inthe ON mode and in the time zone like PRIORITY SPECIAL beyond the time zones 1 3 the pump operates like inthe ON mode and in the time zone like PRIORITY Additionally during loading the WAW accumulator the preset temperature of the water jacket is raised up to 65 C the lt 43 gt Loading temp of WAW special parameter 2 5 Nonvoltage CONTROL output The control unit is equipped with the CONTROL relay whose contacts can be used e g to switch off another heat source when the fireplace works The lt 12 gt CONTROL Relay parameter defines the function of the relay more precisely see PARAMETERS LEVEL 3 REL O CONTROL relay turned off REL 4 Z CONTROL relay turned on The nonvoltage relay described as CONTROL in the schematic diagram Fig 3 enables connecting different kinds of devices controlling another device we want to switch on or switch off acc to the settings PARAMETERS LEVEL 3 of the lt 12 gt CONTROL Relay parameter The output relay is inactive nonvoltage and can be used for handl
13. he heat exchanger it operates if P1 or P2 is activated P3 CH circulating pump 16 One of the sensors T1 or T2 connected The WAW loading pump P1 turns on if the temperature of the WAW accumulator is lower than 50 C the lt 42 gt Minimum temp of WAW parameter and turns offif the temperature is higher than 60 C the lt 41 gt Maximum temp of WAW parameter Both of the sensors T1 low and T2 up connected The loading starts when the temperature sensor T1 measures below 50 C the lt 42 gt Minimum temp of WAW parameter and ends when the temperature sensor T2 measures above 60 C the lt 41 gt Maximum temp of WAW parameter The lt 46 gt Loading mode of WAW parameter should have the value 2 which means the operation of both of the sensors The value 1 causes the operation to be made like at the temperature sensor T2 only active sensor T1 then doesn t take part in the control but its measurements are still shown After the loading of the WAW accumulator ends the pump runs for 1min the lt 45 gt Rundown Time of WAW PUMP which prevents the temperature in the water jacket from rising especially in summer time when the CH pump doesn t operate 2 4 WAW priority and the summer mode OFF The WAW loading pump turned off Only the CH pump can run SUMMER Turning off the heating system in summer time the CH pump doesn t operate Fa Fireplace only works in the preparation function of the WAW or loading
14. hokeV State OFF parameter Default setting is 0 full shut off 2 2 CH pump operation Ifthe fireplace temperature exceeds the preset value of 45 C the lt 31 gt Switch on Temp of PUMPS parameter the CH pump P3 turns on The fireplace inputs with the water jacket optimally operate at water temperature in the range of 45 C 85 C Most producers don t recommend using the water jacket fireplace below the so called dew point The operation in such conditions leads to emitting a lot of condensate on the surface of the furnace The effect originates from too much cooling down combustion gas in the combustion chamber As a result it has anegative impact on the cleanness of the fireplace windowpane efficiency and life time of the fireplace input During loading the warm applicable water accumulator WAW the CH pump can operate cyclically if the WAW mode is set to PRIORITY Limitation of the heat amount flowing into the CH system The cyclical operation is based on turning on the pump for 45 secs and then turning off for 4mins the lt 32 gt Stoptime of CH PUMP parameter ANTIFREEZE Function The control unit protects the system from freezing automatically turning on the circulating pump if the measured temperature is below 4 C ANTISTOP Function The control unit realizes the after season rundown of the pump by switching it on for 1 min if it doesn t operate for a week 2 3 WAW pump operation The control unit controls as wel
15. ibed above MAN OFF AUTO ON Possible operation modes of the WAW accumulator are as follows described above OFF SUMMER ON PRIORITY CLOCK SPECIAL Icon of the current mode Selection of the mode from the list Screen of the clock The screen shows the current time and the number of the activated time zone Time correction is possible after pressing the CONFIRM button 6 OK and the minutes field begins blinking The blinking value can be altered with the buttons 4 4 or 5 Pressing the CHOOSE button 7 you come to the hours field that can be set also with the buttons or Pressing the CONFIRM button 6 x confirms the changes the clock field will stop blinking Screen of setting the parameters Normally the parameters level equals to 0 namely the parameters aren t available After changing the level to 1 2 3 or 4 successive screens show the values of the parameters The last screen contains after which it comes back to the above mentioned screens
16. ign Ifthe manual mode is set FIREPLACE MODE MAN the green LED diode 1 blinks you can manually control the choke valve the button 4 causes the opening of the choke valve one step 10 and the button 5 causes its closing There are the following operation modes of the fireplace h MAN Automatic control locked only manual control of the choke valve is available Green status diode 1 blinks E Setting the choke valve to the rest position the lt 50 gt ChokeV State OFF parameter Green status diode 1 doesn t light AUTO Full automatic burning cycle in the fireplace firing up operation burning out rl Automatic operation is controlled by pressing the button 3 Ft Green status diode 1 lights during the uu fireplace operation and goes out when the burnt out state is detected At the end of the burning out phase the choke valve sets to the rest position 0 full shut off which prevents a room from cooling off and protects the water attachment against freezing ON The choke valve is automatically controlled to stabilize temperature of the water jacket Green status diode 1 does light Automatic operation is activated by pressing the ON OFF button 3 F The choke valve is fully opened In 2hrs the fireplace ought to heat itself and reach the preset temperature stabilized by choke valve movements From that moment the temperature fall to the preset temperature by m
17. in the heating system 45 Rundown 0 10mins Imin Rundown time of the WAW pump The extending of the time Time of for the pump operation after finishing loading the WAW accumulator WAW PUMP It prevents a sudden temperature increase in the fireplace water jacket after ending the loading especially in summer time when the CH pump doesn t run Loading 1 2 1 Kind of loading for the WAW accumulator 46 mode of WAW 1 Temperature sensor T2 down controls the loading of WAW 2 Temperature sensors T1 up and T2 down control the loading of the WAW accumulator 21 ALARM 75 95 C 85 C Fireplace temperature at which the alarm turns on Temp 23 FPLACE OFF 5 25 C 10 C Decreasing fireplace temperature in relation to preset temperature Temp at whose exceeding the countdown of 30mins begins up to the switch off of fireplace stop condition at FIREPLACE MODE AUTO 12 CONTROL 2 6 2 Switch on of the CONTROL relay if Relay 2 fireplace temperature is higher than Switch on Temp of PUMPS WAW temperature measured by T2 sensor is higher 3 than the lt 42 gt Minimum temp of WAW parameter 4 WAW temperature measured by T1 sensor is higher than the lt 42 gt Minimum temp of WAW parameter 5 WAW temperature measured by T2 sensor is higher than the lt 41 gt Maximum temp of WAW parameter 6 fireplace temperature is higher than the lt 21 gt ALARM Temp 51 ChokeV T2 1 Control type of
18. ing turning on off devices making use of the normally closed or opened comets e g gas furnaces ventilation At the normally opened connection you connect COM and NO At the normally closed connection you connect COM and NC Those contacts can be also used for handling any electric device like a pump or electrovalve of 500W max power You have to remember it s a nonvoltage contact that is you need to separately power that connected device through the CONTROL contacts control A gas E furnace control TAr Connecting additional pump Turning off the gas furnace 3 Service of the control unit There are elements on the control panel fig 2 In the turn off state only the orange stanby state LED 1 lights and the graphic display shows current temperature of the water jacket and current time The turn on of the control unit follows by pressing the button 3 F In order to turn it off press once more the button 3 F and at the same time hold it down tor about Isec In case of supply voltage decline the contro unit comes back to the state before the decline The operation state is presented on the graphic display 2 The screens inform about the operation of devices temperature of sensors they make it possible to change the parameters etc The change of screen is done by pressing the CHOOSE button 7 If this is the screen that is able to change a parameter press the CONFIRM button 6 OK which c
19. l the pump P1 loading the warm applicable water accumulator WAW The loading pump can be turned on if water temperature in the fireplace is higher than the preset threshold of 45 C the lt 31 gt Switch on Temp of PUMPS parameter and higher than in the WAW accumulator by 5 C the lt 44 gt Delta Temp of WAW parameter Dependent on the quantity of connected temperature sensors of the WAW accumulator or the buffer there are the following ways of the pump operation Sensors T1 and T2 not connected Loading the WAW accumulator at random The WAW loading pump turns on if water temperature in the fireplace jacket reaches the preset value or is higher than 50 C the lt 42 gt Minimum temp of WAW parameter WARRANTY 1 Warranty is valid 24 months from the date of sale 2 Producer does not take responsibility for any mechanical damages made by user 3 MAKING REPAIRS OR MODYFYING THE DEVICE BY USER IS FORBIDDEN AND CAUSES WARRANTY CANCELATION 4 Warranty card is valid only with date of sale seller s signature and stamp 5 Warranty and after warranty repairs should be done only by producer damaged regulators should be sent to producer in order to make all repairs needed 6 Warranty protection involves the EU 7 Warranty does not exclude not restrict and not suspend buyer s rights coming from the incompatibility of the article with the agreement Laws Journal No 141 Pos 1176 WARNING ANY MODIFICATION OF THE CONTROL UNIT MADE BY
20. nes function disabled 14 ON OFF ON time zones enabled acc to the settings below that is K lt 70 gt lt 79 gt and lt 22 gt 70 Zonel from 0 00 23 4 6 00 Start of the 1st time zone 5 71 Zonel to 0 00 23 4 8 00 End of the 1st time zone 5 72 Zone2 from aaa a 14 00 Start of the 2nd time zone 73 Zone2 to ak as 17 30 End of the 2nd time zone 74 Zone3 from 9 00 23 4 20 00 Start of the 3rd time zone 5 75 Zone3 to ae ei 22 30 End of the 3rd time zone 76 ECO4 from 0 00 23 4 23 00 Start of the 4th time zone economic 5 77 ECO4 to 0 00 23 4 5 00 End of the 4th time zone economic 5 78 ECOS from oeo a 8 00 Start of the 5th time zone economic 79 ECOS to ee 13 30 End of the 5th time zone economic 22 ECO Temp 1 9 C 5 C The lowering of the fireplace temperature in relation to the preset temperature during the economic time zone e4 or e5 p Demonstration procedure of setting the parameters level 1 Press repeatedly the button 7 till the Parameters level 0 parameter setting screen appears Button 6 OK gt 0 blinks Once the button 4 gt 1 blinks Button 6 OK gt 1 stops blinking the Parameters Level 1 has been chosen Parameter Unit Upper and lower thershold of the changes Parameter value change with PARAMETERS ADJUST THE CONTROL UNIT TO THE PROPER
21. ord The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman sets the password e g 1234 and tells it to the user the user has access to the important parameters but without knowing the password the other persons cannot make the changes 5 The user has the unlocked control unit or his own password Serviceman decides the user though oughtn t have access to the important parameters The serviceman locks the control unit with his secret password which removes the user s password and locks the control unit 6 Serviceman doesn t have to know the user s password Always he can use his own secret password and at the end lock with the 9999 which reactivates the user s password 15 PARAMETERS LEVEL 3 PARAMETERS CAN BE CHANGED AT THE UNLOCKED PASSWORD FUNCTION No NAME RANGE DEFAULT SETTING 50 ChokeV 0 100 0 Position of the choke valve in the power supply state State OFF turned off 0 full shut off 100 full opening 32 Stoptime 1 30mins 4mins Break time of the CH pump in the cyclical mode After of CH PUMP that time the pump turns on for 45secs 33 Hysteresis 1 10 C re Temperature hysteresis of turning on off the pumps of PUMPS The temperature difference between turning on and turning off the pumps It prevents from often switchovers especially if there s another heat source
22. ore than 10 C the lt 23 gt FPLACE OFF Temp parameter existing for 30mins is treated as a burnout of the fireplace The control unit ends the operation cycle setting the choke valve to the rest position Pressing the ON OFF button 3 F1 once more starts another operation cycle Green status diode 1 lights during the fireplace operation and goes out after recognizing the burnout state of the fireplace i AUTO operation icon in waiting for the start of a new cycle that is before its start or after its end AUTO operation icon during the cycle It s a stable state that is in order to change it you need to press the CHOOSE button 7 Operation screen of the whole system T1 T2 temperature of the WAW accumulator Temperature of the water jacket of the fireplace x WAW pump doesn t run State of the CONTROL relay Operation mode of the WAW CH pump runs Current time Time 10 The display shows the operation of the WAW P1 and CH P3 pump The pump P3 is not shown because it s switched on parallelly with the pump P1 or P3 It s a stable state that is in order to change it you need to press the CHOOSE button 7 0 Screen of the operation modes_ enables changing the operation mode of the fireplace and WAW accumulator Possible operation modes of the fireplace are as follows descr
23. ssword to be set PASSWORD 9999 HAS CONSIDERABLE MEANING IT CAUSES THE REACTIVATION OF THE PREVIOUS PASSWORD IF PRESENT WITHOUT IT BEING EXPOSED PASSWORD OF PRODUCER S SERVICE IS UNIQUE AND IS NOT DEPENDENT ON THE USER S PASSWORD IT SHOUDN T BE EXPOSED TO THE USER INSTEAD OF THAT THE SERVICE CAN SET THE USER HIS OWN PASSWORD Examples of passwords 1 The control unit is installed with the unlocked password The user can enter his own password e g 1234 From this moment the important parameters cannot be altered without the password being unlocked that is resetting the password 1234 After changing essential parameters the user can leave the control unit unlocked set any new password or enter 9999 which activates the password 1234 2 Producer gives the control unit with the set password The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman enter the secret password or 9999 the user still hasn t access to the important parameters 3 Producer gives the control unit with the set password The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman leaves the control unit unlocked the user now has access to the important parameters He can enter his own password like in example No 1 4 Producer gives the control unit with the set passw
24. the choke valve Mode Continuous control servomotor of the choke valve is always 1 active Dynamic control servomotor of the choke valve is active only if the position change of the valve is needed Parameter number No is of auxiliary role it helps to identify the name e g for different language versions 14 ON OFF j y CHOOSE CONFIRM Fig 2 Control panel view 1 Control unit status diode alarm red standby orange operation green manual MAN blinking green Graphic display Button F1 switch on off power supply Increase button Decrease button Confirmation button Parameter selection button Button F2 for producer COON Ge ee 3 1 Time zones In the default settings the time zones are turned off In order to activate them you need to set the lt 14 gt Time zones parameter to ON The control unit is equipped with the clock which enables the automatic change of the control unit operation at different times of day 24 hrs are divided into 5 time zones 1 2 3 e4 e5 and the single time when no zone is active that is ZONE 0 or BAZA BASE Each zone has a start time FROM and an end time TO The same start and end time means the zone isn t active which doesn t change the settings of the control unit The time zones can overlap each other in that case binding are the settings for the
Download Pdf Manuals
Related Search