Multimeter with IR Thermometer
Contents
1. IF THE METER IS TO BE STORED FOR A LONG PERIOD OF TIME the batteries should be removed to prevent damage to the unit BATTERY and FUSE Replacement WARNING To avoid electric shock disconnect the test leads from any source of voltage before removing the battery cover PS Turn power off and disconnect the test leads from the meter Lift the meter stand to expose the battery cover Open the rear battery fuse compartment by removing the Phillips head screw on the lower rear of the meter Carefully pull down on the cover just enough to release the latch and then lift it off The cover will not pull down all the way Remove the old battery or fuse and install a new one of the correct rating Place the battery fuse cover back in place Secure with the screw WARNING To avoid electric shock do not operate the meter until the battery cover is in place and fastened securely NOTE If the meter does not work properly check the fuses and replace the battery to make sure that they are still good and that they are properly inserted Battery Safety Reminders o Please dispose of batteries responsibly observe local state and national regulations o Never dispose of batteries in a fire batteries may explode or leak o Never mix battery types install new batteries of the same type 10 EX210_EX210T en US_v1 5 9 15 Specifications Function Range Resol2. Rotate the function switch to the D position 2 Insert the black lead banana plug into the negative COM jack Insert the red test lead banana plug into the positive 2 jack 3 Press the MODE button to indicate M on the display 4 Touch the test probe tips to the circuit or wire you wish to check 5 If the resistance is less than the continuity threshold the audible signal will sound DIODE TEST 1 Rotate the function switch to the green position 2 Insert the black test lead banana plug into the negative COM jack and the red test lead banana plug into the positive Dt jack 3 Press the MODE button to indicate gt and V on the display 4 Touch the test probes to the diode under test Forward voltage will typically indicate 0 400 to 0 700V Reverse voltage will indicate OL Shorted devices will indicate near OV and an open device will indicate OL in both polarities 7 EX210_EX210T en US_v1 5 9 15 NON CONTACT INFRARED TEMPERATURE MEASUREMENTS 1 Rotate the function switch to the IR position The upper right four digit temperature display will switch on 2 Press the MODE button to select F or C 3 Aim the infrared sensor top of meter at the surface to be measured 4 Press and Hold the IRT button to turn on the IR thermometer and laser pointer The laser pointer identifies the surface spot to be measured and SCAN will flash in the display 5 Read the temperature in the display
3. of shipment a six month limited warranty applies to sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department for authorization Visit the website www extech com for contact information A Return Authorization RA number must be issued before any product is returned The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification FLIR Systems Inc specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages FLIR s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied Calibration Repair and Customer Care Services FLIR Systems Inc offers repair and calibration services for the Extech Instruments products we sell NIST certification for most products is also provided Call the Customer Service Department for information on calibration services available for this product Annual calibrations should be performed to verify meter performance an
4. 3063 USA Certificado ISO 9001 Copyright O 2013 2015 FLIR Systems Inc Reservados todos los derechos incluyendo el derecho de reproducci n total o parcial en cualquier medio www extech com 15 EX210_EX210T en US_v1 5 9 15
5. 6 The area of the surface to be measured must be larger than the spot size as determined by the distance to spot size values listed in the specification table 7 Release the IRT O button to turn the IR thermometer and laser pointer off HOLD and the final measured value will remain in the display WARNING Do not directly view or direct the laser pointer at an eye Low power visible lasers do nat normally present a hazard but may present some potential for hazard if viewed directly for extended periods of time AVOID EXPOSURE ATM Laser radiation is emitted from this aperture LASER RADIATION DO NOT STARE INTO BEAM OUTPUT lt 1mW WAVELENGTH 630 670nm CLASS 2 LASER PRODUCT Complies with FDA 21 CFR 1040 10 and 1040 11 IEC 60825 1 2001 08 Edition 1 2 EN 60825 1 1994 A11 1996 A2 2001 A1 2002 IR Spot to Distance Diagram The 4 1 spot to distance ratio determines the size of the measured surface area with respect to the distance the meter is held away from the surface IR Measurement Notes 1 The object under test should be larger than the spot target size calculated by the field of view diagram 2 Ifthe surface of the object under test is covered with frost oil grime etc clean before taking measurements 3 If an object s surface is highly reflective apply masking tape or flat black paint to the surface before measuring 4 The meter will not make measurements through glass steam
6. User Guide EXTECH INSTRUMENTS Multimeter with IR Thermometer Extech EX210 and EX210T True RMS Introduction Thank you for selecting the Extech EX210 EX210T True RMS EX210T only Autoranging Multimeter This meter measures AC DC Voltage AC DC Current Resistance Diode Test and Continuity plus non contact InfraRed Temperature Proper use and care of this meter will provide many years of reliable service Please visit the Extech Instruments website www extech com to check for the latest version of this User Guide Extech Instruments is an ISO 9001 certified company Safety This symbol adjacent to another symbol terminal or operating device indicates that the operator must refer to an explanation in the Operating Instructions to avoid personal injury or damage to the meter This CAUTION symbol indicates a potentially hazardous situation which if not CAUTION A avoided may result damage to the product This WARNING symbol indicates a potentially hazardous situation which if not avoided could result in death or serious injury MAX 600V This symbol advises the user that the terminal s so marked must not be connected to a circuit point at which the voltage with respect to earth ground exceeds in this case 600 VAC or VDC voltages For maximum safety the meter and its test leads should not be handled when these terminals are energized This symbol indicates tha
7. com R parations et retours Option 4 E mail repair extech com Les sp cifications produit sont sujettes modifications sans pr avis Pour les toutes derni res informations veuillez visiter notre site Web www extech com FLIR Commercial Systems Inc 9 Townsend West Nashua NH 03063 USA Certifi ISO 9001 Copyright O 2013 2015 FLIR Systems Inc Tous droits r serv s y compris la reproduction partielle ou totale sous quelque forme que ce soit www extech com 14 EX210_EX210T en US_v1 5 9 15 Garantia FLIR Systems Inc garantiza este dispositivo marca Extech Instruments para estar libre de defectos en partes o mano de obra durante un a o a partir de la fecha de embarque se aplica una garant a limitada de seis meses para cables y sensores Si fuera necesario regresar el instrumento para servicio durante o despu s del periodo de garant a llame al Departamento de Servicio a Clientes para obtener autorizaci n Visite www extech com para Informaci n de contacto Se debe expedir un n mero de Autorizaci n de Devoluci n AD antes de regresar cualquier producto El remitente es responsable de los gastos de embarque flete seguro y empaque apropiado para prevenir da os en tr nsito Esta garant a no se aplica a defectos resultantes de las acciones del usuario como el mal uso alambrado equivocado operaci n fuera de las especificaciones mantenimiento o reparaci n inadecuada o modificaci n no autorizada FLIR S
8. d accuracy Technical support and general customer service is also provided refer to the contact information provided below Support Lines U S 877 439 8324 International 1 603 324 7800 Technical Support Option 3 E mail support extech com Repair amp Returns Option 4 E mail repair extech com Product specifications are subject to change without notice Please visit our website for the most up to date information www extech com FLIR Commercial Systems Inc 9 Townsend West Nashua NH 03063 USA ISO 9001 Certified Copyright O 2013 2015 FLIR Systems Inc All rights reserved including the right of reproduction in whole or in part in any form www extech com 13 EX210_EX210T en US_v1 5 9 15 Garantie FLIR Systems Inc garantit que cet appareil Extech Instruments est exempt de d fauts mat riaux et de fabrication pendant un an partir de la date d envoi une garantie limit e de six mois s applique aux capteurs et aux c bles Si le renvoi de l appareil pour r paration devient n cessaire durant ou apr s la p riode de garantie contactez le service client pour autorisation Pour obtenir les coordonn es visitez le site Web suivant www extech com Un num ro d autorisation de retour AR doit tre d livr avant tout retour de produit L exp diteur prend sa charge les frais d exp dition le fret l assurance et l emballage correct de l appareil afin de pr venir toute d t rioration durant le transport Cett
9. dust and smoke 5 To find a hot spot aim the meter outside the area of interest then scan across in an up and down motion until the hot spot is located 8 EX210_EX210T en US_v1 5 9 15 AUTORANGING MANUAL RANGE SELECTION When the meter is first switched on it automatically enters the AutoRanging mode This automatically selects the best range for the measurements being made and is generally the best mode for most measurements For measurement situations requiring that a range be manually selected perform the following 1 Press the RANGE button The AUTO display indicator will turn off 2 Press the RANGE key to step through the available ranges until the range desired is selected 3 Press and hold the RANGE button for 2 seconds to exit manual ranging Note Manual ranging does not apply to the Temperature Diode and Continuity functions MAX MAXIMUM READING MODE 1 Press the MAX button to activate the MAX mode The display icon MAX will appear The meter will display and hold the maximum reading and will update only when a new maximum value is detected 2 Press the MAX button again to exit the mode Note Max does not apply to the Resistance Diode and Continuity functions DISPLAY BACKLIGHT Press and hold the IRT 8 button for 2 second to turn the backlight on The backlight will automatically turn off after approximately 10 seconds or press and hold the button again for 2 seconds to manually turn it off HOLD T
10. e garantie ne s applique pas aux dommages imputables l utilisateur tels que l usage impropre ou abusif un mauvais c blage une utilisation non conforme aux sp cifications un entretien ou une r paration incorrecte ou toute modification non autoris e FLIR Systems Inc d clinera sp cifiquement toute garantie ou qualit marchande ou aptitude l emploi pr vu et ne sera en aucun cas tenu responsable pour tout dommage cons quent direct indirect ou accidentel La responsabilit totale de FLIR est limit e la r paration ou au remplacement du produit La garantie d finie ci dessus est inclusive et aucune autre garantie crite ou orale n est exprim e ou implicite Calibrage r paration et services apr s vente FLIR Systems Inc offre des services de calibrage et de r paration pour les produits Extech Instruments que nous commercialisons Nous fournissons galement une certification NIST pour la plupart des produits Contactez notre service client pour toute information sur les services de calibrage disponibles pour ce produit Un calibrage doit tre effectu chaque ann e pour v rifier les performances et la pr cision du m tre Nous offrons galement une assistance technique et un service la client le Veuillez vous reporter aux coordonn es fournies ci dessous Lignes d assistance tats Unis 877 439 8324 international 1 603 324 7800 Service d assistance technique Option 3 E mail support extech
11. e input jack 12 COM input jack X D OL Note Tilt stand test lead holders and battery compartment are on rear of unit Symbols and Enunciators lt a Continuity gt t Diode test u micro 10 amps m milli 10 volts amps A Amps k kilo 10 ohms M mega 10 ohms Q Ohms V Volts AC Alternating current DC Direct current F Degrees Fahrenheit C Degrees Centigrade MAX Maximum AUTO Autoranging HOLD Display hold SCAN _ IR temperature in progress HoD HN CL aio EX210_EX210T en US_v1 5 9 15 Operating Instructions WARNING Risk of electrocution High voltage circuits both AC and DC are extremely dangerous and should be measured with great care 1 ALWAYS turn the function switch to the OFF position when the meter is not in use 2 If OL appears in the display during a measurement the value exceeds the range you have selected Change to a higher range AC DC VOLTAGE MEASUREMENTS CAUTION Do not measure DC voltages if a motor on the circuit is being switched ON or OFF Large voltage surges may occur that can damage the meter 1 Rotate the function switch to the VAC or VDC position 2 Insert the black test lead banana plug into the negative COM jack Insert the red test lead banana plug into the positive V jack 3 Touch the black test probe tip to the negative side of the circuit Touch the red test probe tip to the positive side of the circuit 4 Read the v
12. f the test leads and the meter itself for any damage before operating the meter e Use great care when making measurements if the voltages are greater than 25 VAC rms or 35 VDC These voltages are considered a shock hazard e Warning This is a Class A device This device can cause interference in residential areas e Always discharge capacitors and remove power from the device under test before performing Diode Resistance or Continuity tests e Voltage checks on electrical outlets can be difficult and misleading because of the uncertainty of connection to the recessed electrical contacts Other means should be used to ensure that the terminals are not live e If the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired e This device must not be used by children It contains hazardous objects as well as small parts that the children could swallow e Do not leave batteries and packing material lying around unattended they can be dangerous to children e Inthe event that this device will be stored for an extended period of time remove the batteries e Expired or damaged batteries can leak and can be hazardous to skin Use suitable hand gloves in such cases e Do not short circuit the battery Do not place the battery near a fire e Never mix battery types Always install new batteries of the same type 3 EX210_EX210T en US_v1 5 9 15 SAFETY INSTRUCTIONS Th
13. he HOLD function freezes the reading in the display Press the HOLD button momentarily to activate or to exit the HOLD function Note The HOLD button does not function in the IR measurement mode AUTO SLEEP If no button is pressed the auto sleep feature will place the meter in sleep mode after approximately 15 minutes of operation If this happens press any button to wake the meter or switch the meter to OFF if it no longer in use 9 EX210_EX210T en US_v1 5 9 15 Maintenance WARNING To avoid electric shock disconnect the test leads from any source of voltage before removing the back cover or the battery or fuse covers WARNING To avoid electric shock do not operate the meter until the battery and fuse covers are in place and fastened securely This MultiMeter is designed to provide years of dependable service if the following care instructions are followed 1 6 KEEP THE METER DRY If it gets wet wipe it off 2 USE AND STORE THE METER IN NORMAL TEMPERATURES Temperature extremes can shorten the life of the electronic parts and distort or melt plastic parts HANDLE THE METER GENTLY AND CAREFULLY Dropping it can damage the electronic parts or the case KEEP THE METER CLEAN Wipe the case occasionally with a damp cloth DO NOT use chemicals cleaning solvents or detergents USE ONLY FRESH BATTERIES OF THE RECOMMENDED SIZE AND TYPE Remove old or weak batteries so they do not leak and damage the unit
14. is meter has been designed for safe use but must be operated with caution The rules listed below must be carefully followed for safe operation 1 NEVER apply voltage or current to the meter that exceeds the specified maximum Input Protection Limits Function Maximum Input V AC DC Resistance Diode Test Continuity 600 VDC AC rms yA or mA AC DC 200mA fused A ACIDC 10A fused USE EXTREME CAUTION when working with high voltages DO NOT measure voltage if the voltage on the COM input jack exceeds 600V above earth ground NEVER connect the meter leads across a voltage source while the function switch is in the current resistance or diode mode Doing so can damage the meter ALWAYS discharge filter capacitors in power supplies and disconnect the power when making resistance or diode tests ALWAYS turn off the power and disconnect the test leads before opening the covers to replace the fuse or batteries NEVER operate the meter unless the back cover and the battery and fuse covers are in place and fastened securely If the equipment is used in a manner not specified by the manufacturer the protection provided by the equipment may be impaired 4 EX210_EX210T en US_v1 5 9 15 Controls and Jacks IR Thermometer Laser Pointer 2000 count LCD MAX button MODE button FUNCTION switch mA pA and 10A input jacks O NO ANA IR Thermometer button 9 HOLD button 10 RANGE button 11 Positiv
15. old 20 to 50Q test current lt 1 5mA Input Impedance AC Response ACV Bandwidth IR Spectral response IR Emissivity IR distance ratio Laser pointer Display Overrange indication Auto Power Off Polarity Measurement Rate Battery Fuses Operating Temperature Storage Temperature Operating Humidity Storage Humidity Operating Altitude Weight Size Safety Approvals 10MQ VDC VAC True rms EX210T only 40Hz to 1000Hz 6 to 16um 0 95 fixed 4 1 Class 2 laser lt 1mW power Wavelength is 630 to 670nm 2 000 count backlit liquid crystal display OL is displayed 15 minutes approximately Automatic no indication for positive Minus sign for negative 2 times per second nominal One 9 volt NEDA 1604 battery mA HA ranges 200mA 250V ceramic fast blow A range 10A 600V ceramic fast blow 14 F to 122 F 10 C to 40 C 14 F to 140 F 10 C to 60 C Max 80 up to 31 C 87 F decreasing linearly to 50 at 40 C 104 F lt 80 7000 ft 2000m maximum 9 17 oz 260 g 5 8x2 9x1 6 147x76x42 mm This meter is intended for origin of installation use and protected against the users by double insulation per IEC EN 61010 1 2001 and IEC EN 61010 031 2002 to Category III 600V Pollution Degree 2 CE 12 EX210_EX210T en US_v1 5 9 15 Warranty FLIR Systems Inc warrants this Extech Instruments brand device to be free of defects in parts and workmanship for one year from date
16. oltage in the display AC DC CURRENT MEASUREMENTS 1 Insert the black test lead banana plug into the negative COM jack 2 Press the MODE button to indicate DC or AC on the display 3 For current measurements up to 2000pA set the function switch to the pA position and insert the red test lead banana plug into the pA mA jack 4 For current measurements up to 200 mA DC set the function switch to the mA position and insert the red test lead banana plug into the HA mA jack 5 For current measurements up to 10A DC set the function switch to the 10A position and insert the red test lead banana plug into the 10A jack 6 Connect the test leads in series with the circuit under test 7 Apply power to the circuit 8 Read the current in the display 6 EX210_EX210T en US_v1 5 9 15 RESISTANCE MEASUREMENTS WARNING To avoid electric shock disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements Remove the batteries and unplug the line cords 1 Rotate the function switch to the Q position 2 Insert the black test lead banana plug into the negative COM jack Insert the red test lead banana plug into the positive Q jack 3 Touch the test probe tips across the device under test 4 Read the resistance in the display CONTINUITY CHECK WARNING To avoid electric shock never measure continuity on circuits or wires that have a voltage potential 1
17. t a device is protected throughout by double insulation or reinforced insulation This symbol adjacent to one or more terminals identifies them as being associated with ranges that may in normal use be subjected to particularly hazardous PER IEC1010 OVERVOLTAGE INSTALLATION CATEGORY OVERVOLTAGE CATEGORY I Equipment of OVERVOLTAGE CATEGORY is equipment for connection to circuits in which measures are taken to limit the transient overvoltages to an appropriate low level Note Examples include protected electronic circuits OVERVOLTAGE CATEGORY II Equipment of OVERVOLTAGE CATEGORY ll is energy consuming equipment to be supplied from the fixed installation Note Examples include household office and laboratory appliances OVERVOLTAGE CATEGORY III Equipment of OVERVOLTAGE CATEGORY III is equipment in fixed installations Note Examples include switches in the fixed installation and some equipment for industrial use with permanent connection to the fixed installation OVERVOLTAGE CATEGORY IV Equipment of OVERVOLTAGE CATEGORY IV is for use at the origin of the installation Note Examples include electricity meters and primary over current protection equipment 2 EX210_EX210T en US_v1 5 9 15 CAUTIONS e Improper use of this meter can cause damage shock injury or death Read and understand this user manual before operating the meter e Always remove the test leads before replacing the battery or fuses e Inspect the condition o
18. ution Accuracy DC Voltage 200 mV 0 1 mV 0 8 reading 6 digits 2V 0 001V 0 5 reading 2 digits 20V 0 01V 200V 0 1V 0 8 reading 2 digits 600V 1V AC Voltage 200 mV 0 1 mV 50 60Hz 2V 0 001V 20V 0 01V 1 5 reading 6 digits True RMS 200V 0 1V EX210T only 600V 1V All AC voltage ranges are specified from 5 of range to 100 of range DC Current 200 pA 0 1 pA 2000 pA 1 pA 1 5 reading 5 digits 20 mA 0 01 mA 200 mA 0 1 mA 2 000 0 001 A 2 5 reading 5 digits 10A 0 01A Note 10A for 30 sec max AC Current 200 pA 0 1 HA 50 60Hz 2000 pA 1 pA 1 5 reading 8 digits 20 mA 0 01 mA True RMS 200 mA 0 1 mA EX210T only 2 000 0 001 3 0 reading 5 digits 10A 0 01 A Note 10A for 30 sec max NOTE Accuracy is stated at 18 C to 28 C 65 F to 83 F and less than 75 RH EX210_EX210T en US_v1 5 9 15 Function Range Resolution Accuracy Resistance 200 Q 0 1Q 0 8 reading 5 digits 2kQ 0 001 kQ 20 kQ 0 01 kQ 0 8 reading 2 digits 200 kQ 0 1 KQ 2MQ 0 001 MQ 2 5 reading 8 digits 20 MQ 0 01 MQ Temperature IR 20 to 0 C 4 C 0 to 93 C 2 0 rdg or 2 C 93 to 230 C 3 0 rdg or 3 C 0 1 C F 5 to 32 F 8 F 32 to 200 F 2 0 rdg or 4 F 200 to 446 F 3 0 rdg or 6 F Enclosure Double molded Diode Test Test current of 0 9mA maximum open circuit voltage 2 8V DC typical Continuity Thresh
19. ystems Inc rechaza especificamente cualesquier garant as impl citas o factibilidad de comercializaci n o idoneidad para cualquier prop sito determinado y no ser responsable por cualesquier da os directos indirectos incidentales o consecuentes La responsabilidad total de FLIR est limitada a la reparaci n o reemplazo del producto La garant a precedente es inclusiva y no hay otra garant a ya sea escrita u oral expresa o impl cita Servicios de calibraci n reparaci n y atenci n a clientes FLIR Systems Inc ofrece servicios de reparaci n y calibraci n para los productos que vendemos de Extech Instruments Adem s ofrecemos certificaci n NIST para la mayor a de los productos Llame al Departamento de Servicio al Cliente para solicitar informaci n de calibraci n para este producto Para verificar el funcionamiento y precisi n se debe realizar la calibraci n anual Adem s se provee Soporte T cnico y servicios generales al cliente consulte la informaci n de contacto en seguida L neas de soporte EE UU 877 439 8324 Internacional 1 603 324 7800 Soporte T cnico Opci n 3 correo electr nico support extech com Reparaci n Devoluciones Opci n 4 correo electr nico repair extech com Las especificaciones del producto est n sujetas a cambios sin aviso Por favor visite nuestra p gina en Internet para la informaci n m s actualizada www extech com FLIR Commercial Systems Inc 9 Townsend West Nashua NH 0
Download Pdf Manuals
Related Search