Serial Port Adapter
Contents
1. Adapter Wizard for easy configuration 10 2 Installation Before using your Serial Port Adapter it must be connected to its host system and it must be connected to a power supply The installation differs slightly from model to model This chapter describes how to install your Serial Port Adapter 2 1 OEM Serial Port Adapters If you are using the OEM Serial Port Adapter please refer to the Electrical amp Mechanical Datasheet for the specific model for installation instructions The latest Electrical 8 Mechanical Datasheet can be downloaded from www connectblue se 2 2 Serial Port Adapter 3121 2 2 1 Mounting 25 70 63 50 21 00 Picture 3 The Serial Port Adapter can be mounted using the mounting holes 11 DIN socket M3x25 mm screwes Picture 4 The Serial Port Adapter can be mounted on a DIN socket using the mounting holes Note that the Serial Port Adapter 3121 has internal antenna Therefore it cannot be mounted inside a shielded enclosure 2 2 2 Power Supply If you are not using the power adapter provided with the product of if there is none provided you must use a DC plug 2 1 mm centerpin connector The product shall have a power supply of 5 VDC min 200 mA on the power connector UU Restore Fu2. e Serial Port Profile e Dial up Networking Profile e LAN Access Profile When creating end products based on the Serial Port Adapter the following applies e The end product does not have to be re qualified e A free of charge Bluetooth End Product Listing EPL must be completed at the Bluetooth SIG website www bluetooth org This applies for all products implementing Bluetooth technology The EPL requires no testing online listing only and is good marketing since the product is published at the B vetooth web site www bluetooth com When creating the EPL you shall refer to the Qualified Design ID QDID of the connectBlue device Easy to follow EPL guides are available at www bluetooth org to assist you with the EPL A free of charge Bluetooth SIG Adopter membership is required e The Bluetooth trademark may be placed on the end product and or used in material related to the end product This requires a free of charge Bluetooth SIG Adopter membership For more information see www bluetooth org For more information please visit www connectblue com LAN profile only supported in RSPA333s 23 5 Additional Information 5 1 Guidelines for Efficient and Safe Use Read this information before using your Serial Port Adapter For any exceptions due to national requirements or limitations when using your Serial Port Adapter please visit www bluetooth com Note Changes or modifications to the pro
3. restore button see Picture 5 is pressed during power on the default serial settings as well as the default escape sequence are restored If the function button see Picture 5 is pressed and a remote peer is configured for external connect the connect attempt is initiated See AT Command Specification for further details The status LED uses the following color indications 13 e Green The current mode is data mode and no connection attempt is in progress e Orange The current mode is AT mode e Purple A connection attempt is in progress e Blue A connection is currently active e Blue Blinking A connection is active and data is transmitted or received over air e Red Blinking Buffer overflow parity or framing error detected on the UART 2 3 Rugged Serial Port Adapter 333s 2 3 1 Mounting 85 50 JC ai Wi O ES A BA E D KL D d E O 3 a 3 d 8 NI Co LI al LO O 2 1 i Y Y mm Tolerance 1 0 On CH Picture 8 The Serial Port Adapter can be mounted using the mounting holes Rugged Serial P
4. the product e Make sure all cords and cable are positioned so that they will not be stepped on tripped over or otherwise subject to damage or stress e To reduce risk of electric shock unplug the unit from any power source before attempting to clean it 5 2 Troubleshooting This section lists some problems that you might encounter while using your Serial Port Adapter 1 cannot connect The data send to the Serial Port Adapter does not arrive at the remote device e Make sure that you have connected power to your Serial Port Adapter The LED indicator should emit a green light when powered up being ready to send and receive data e Your Serial Port Adapter is not configured to use the same serial settings e g baud rate as your host system Use the configuration wizard to set the correct baud rate 26 You have configured your Serial Port Adapter to act as a client but you have not selected a server device to connect to Select a server device using the configuration wizard Your Serial Port Adapter is too far away from the selected server device Move the Serial Port Adapter closer to the server device You are not using the correct Bluetooth profile Your Serial Port Adapter must be configured to use the same profile as the device you want to communicate with The remote device is not in connectable mode If the server device is another Serial Port Adapter use the configuration wizard to set the device in
5. 65 5 3 8 Dimensions Model Dimensions with x depth x height Serial Port Adapter 312i 63 5 x 81 5 x 25 7 mm see 2 2 1 Rugged Serial Port Adapter 333s 75 8 x 85 5 x 35 mm see 2 3 1 29
6. DSR 6 nts 3 3 RTS 7 RTS 7 CTS 8 ra lt Q CTS 8 Picture 10 Crossover cable RD2 a TD 2 i TD 3 RD 3 SE 3 k m 3 DTR 4 DSR 4 a EK ba E 2 GND 5 GND 5 EN E Ee DSR 6 DTR 6 S 3 RTS 7 p gt CTS 7 CTS 8 lt q RTS 8 Picture 11 Straight cable 2 3 4 RS422 In this model the same DSUB connector is used when using RS232 RS422 and RS485 However in the case of RS422 and RS485 the pins have different meanings compared to RS232 For details please read the AT command specification document In the RS422 case the following pinning is used e Pin 1 R input receiver e Pin 2 T output transmitter e Pin 3 NC not connected e Pin 4 NC not connected e Pin 5 NC not connected e Pin 6 R input receiver e Pin 7 NC not connected e Pin 8 T output transmitter e Pin 9 NC not connected For four wire RS422 multidrop the following connection setup shall be used pl R T Serial Port Adapter Serial Port Adapter R Picture 12 Four wire RS422 connection setup Note The definition of R R T T may vary between manufacturers 17 2 3 5 RS485 In the case of RS485 the same pinning as for RS422 is used except that pins T and R must be connected externally and pins T and R must be connected externally to produce the signals T R and T R For two wire RS485 multidrop the following connection setup shall be used Seria
7. INDUSTRIAL BLUETOOTH E Bluetooth Serial Port AdapterTM Product Guide 3 3 cB SPA312 cB RSPA333 connectBlue Serial Port Adapter Product Guide Copyright 2006 connectBlue 48 The contents of this document can be changed by connectBlue AB without prior notice and do not constitute any binding undertakings from connectBlue AB connectBlue AB is not responsible under any circumstances for direct indirect unexpected damage or consequent damage that is caused by this document All rights reserved Release 0910 Document version 3 4 Document number cBProduct 0610 05 8 Printed in Sweden Trademarks Registered trademarks from other companies are Bluetooth is a trademark owned by the Bluetooth SIG Inc Microsoft Windows Windows NTTM Windows 2000 Windows CETM Windows METM Windows XPTM are registered trademarks from Microsoft Corporation Contents INTRODUCTION so sssecdscescsssnceces wcdteavesesececes cess oucescesceteccsbencdeesossesocteossoves 8 Lt RELATED DOCUMENTS ci ia 9 1 2 WHAT IS BLUETOOTH WIRELESS TECHNOLOGY 9 1 3 HOW CAN I USE MY SERIAL PORT ADAPTER pp 10 1 4 GETTING STARTED di 10 TNS TAL LA TION 11 2 1 OEM SERIAL PORT ADAPTERS pp 11 2 2 SERIAL PORT ADAPTER 2121 11 A OS A TOS 11 LRD POWEF SUPPLY ci aii 12 DPS RII ZAS ASS AS AS ANO 12 RE ER and LED rerien ces iss aoe vba ae ee EA ES 13 2 3 RUGGED SERIAL PORT ADAPTER 331 14 EE Mounting cise cee pen
8. ay cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 3 1 1 RF Exposure Statement This transmitter MUST have a separation distance of at least 20 cm between the antenna and the body of the user or nearby persons excluding hands wrists feet and ankles If the radio is installed in a laptop display transmission MUST be prevented if the lid 15 closed to ensure that the minimum distance of 20 cm between the user and the transmitting antenna is maintained Any notification to the end user of installation or removal instructions about the integrated radio is NOT allowed 3 1 2 Antenna The antenna is fixed and cannot be removed or replaced by the user 20 3 1 3 Caution Any changes or modifications NOT explicitly APPROVED by connectBlue AB could cause the device to cease to comply with FCC rules part 15 and thus void
9. connectable mode If the device is another Bluetooth device consult the manual for that device to set it in connectable mode Make sure that the Serial Port Adapter 15 in transparent data mode green light Make sure that the Serial Port Adapter is not in configuration mode orange light After configuring your Serial Port Adapter remember to exit the configuration wizard before disconnecting it from the PC If high security mode has been selected on one of the devices wanting to communicate the two devices have to be paired with each other Either disable security or perform pairing Also note that pairing is automatic during a connection setup if it is needed The Bluetooth link between my Serial Port Adapter and my selected remote peer disconnects Your Serial Port Adapter is configured to disconnect if no data 15 received or sent during a longer period of time Use the configuration wizard to disable the automatic disconnect or change the value of the timer Your Serial Port Adapter is too far away from the device it is communicating with Move the two devices closer to each other There is no color on the LED indicator Make sure that power is connected to the Serial Port Adapter When search for other devices using the configuration wizard cannot find the device I m searching for The remote device is too far away Move it closer to your Serial Port Adapter The remote device is not in discoverable mode If the remote
10. d cess hes E R 14 St POWer SUPPLY NAS 15 EE PE e EE 15 CO 76 PAE IRSAS EREE A babies cide AE E EAA E lacie kate a ees 18 23 6 BUHO AMADA tata 18 REGULATORY INEORMATION ir 20 IL ECC STATEMEN EE 20 7 RF Exposure Ge111E11 ee 20 20 27 3 2 DECLARATION OF CONFORMITY pp 22 BLUETOOTH QUALIFICATION uu csssscccsssscccssssccccssseccccssseccscsssees 23 ADDITIONAL INFORMATION ccsscsssssssssssccccccccssssscceccccscssssssecee 24 5 1 GUIDELINES FOR EFFICIENT AND SAFE USE 24 TAL Product Care maue ae S TEN A AE E 24 5 1 2 Radio Frequency EXPOSUre serren 24 5 1 3 Electronic lt 0074072777070 0 26 5 1 4 Potentially Explosive Atmospheres ccoo 26 D215 POWer EE 26 3 2 TROUBLESHOOTING o Gui ii 26 5 3 TECHNICAL SPECIFICATIONS cccoconnononnnnnnononnnnononononnononnanonnnoncononannanononos 27 3 2 7 7 7 7677 27 5 3 2 Certifications and Complieoece coo 28 3 3 3 Type Approval o sdi CE EEEE inner 28 5 3 4 Radio Output oe 28 5 3 3 Power SUDPIV Ee iniae aian a ARA S a R STT S a 28 E EE 26 0 26 5 3 8 er 29 1 Introduction Congratulations on your purchase of a connectBlue Serial Port AdapterTM The Serial Port Adapter can be used as a component in many t
11. device is a Serial Port Adapter use the configuration wizard to set it in discoverable mode If the remote device is another device consult the manual of that device to set it in discoverable mode 5 3 Technical Specifications 5 3 1 Environmental Storage temperature 30 85 C Maximum operating temperature 30 85 C 27 Humidity RH 5 90 non condensing Shock and vibration IEC 61131 2 5 3 2 Certifications and Compliance EMC compliance ENV 50081 1 ENV 50081 2 Environment IEC 61131 2 Medical IEC 60601 01 2 5 3 3 Type Approval FCC CFR 47 part 15 for RSPA333s SPA312i ETS 300 328 300 826 5 3 4 Radio Output Power Model Output Power Serial Port Adapter 312i 7 dBm Rugged Serial Port Adapter 3335 16 9 dBm 0 dBm 1 MW 4dBM 2 5 mW 20 dBm 100 mW 5 3 5 Power Supply Model Power Supply Serial Port Adapter 312i 5 VDC Rugged Serial Port Adapter 333s 8 30 VDC 5 3 6 Serial Interface Model Serial Interface Serial Port Adapter 312i RS232 male DSUB 9 300 921600 baud CTS RTS flow control or no flow control Rugged Serial Port Adapter 333s RS232 RS422 RS485 male DSUB 9 300 921600 baud CTS RTS flow control or no flow control 5 3 7 Housing Model Housing Serial Port Adapter 312i Plastic housing 1020 28 Rugged Serial Port Adapter 3335 Aluminum housing 10
12. duct not expressly approved by connectBlue AB will void the user s authority to operate the equipment 5 1 1 Product Care e Do not expose your product to liquid or moisture e Do not expose you product to extreme hot or cold temperature see Technical Specification for further information e Do not expose your product to lit candles cigarettes cigars open flames etc e Do not drop throw or try to bend your product since rough treatment could damage your product e Do not attempt to disassemble your product Doing so will void warranty The product does not contain consumer serviceable or replaceable components Service should only be performed by connectBlue AB e Do not paint your product as the paint could prevent normal use e Ifyou will not be using your product for a while store it in a place that is dry free from damp dust and extreme heat and cold e The clearance and creepage distances required by the end product must be withheld when the module is installed e The cooling of the end product shall not negatively be influenced by the installation of the module when the module is installed 5 1 2 Radio Frequency Exposure The Serial Port Adapter contains a small radio transmitter and receiver During communication with other Bluetooth products the Serial Port Adapter receives and transmits radio frequency RF electromagnetic fields microwaves in the frequency range 2400 to 2500 MHz The output power of the radio
13. icates with its host system using RS232 RS422 or RS485 Once connected to its host system and configured the Serial Port Adapter can communicate using Bluetooth with a wide range of other Bluetooth enabled devices such as other Serial Port Adapters mobile phones handheld computers and laptops RS232 422 485 Logic level UART Picture 2 The Serial Port Adapter connected to the controller communicates wirelessly with a Bluetooth enabled Laptop The Serial Port Adapter can initiate as well as accept connections to and from other Bluetooth devices When initiating a connection to another device the Serial Port Adapter acts as a client When accepting a connection from another device the Serial Port Adapter acts as a server In most cases the Serial Port Adapter communicates with one Bluetooth device at a time but in some variants it is possible for the Serial Port Adapter to simultaneously communicate with several Bluetooth devices This feature 15 called Wireless Multidrop For further details please read the Serial Port Adapter AT Command Specification or the ECI Protocol Specification 1 4 Getting Started Before using your Serial Port Adapter you must e Install your Serial Port Adapter For more information see chapter 2 e Configure your Serial Port Adapter For more information please read the Serial Port Adapter AT Command Specification or the ECI Protocol Specification It is also possible to use the Serial Port
14. l Port Adapter Serial Port Adapter T R T R 00002 H Devices Picture 13 Two wire RS485 connection setup 2 3 6 Button and LED If the restore button see Picture 9 is pressed during power on the default serial settings as well as the default escape sequence are restored The status LED uses the following color indications e Green The current mode is data mode and no connection attempt is in progress e Orange The current mode is AT mode e Purple A connection attempt is in progress e Blue A connection is currently active e Blue Blinking A connection is active and data is transmitted or received over air e Red Blinking Buffer overflow parity or framing error detected on the UART 18 19 3 Regulatory Information 3 1 FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy ana if not installed and used in accordance with the instructions m
15. nction AA Picture 5 DC plug 2 1 mm centerpin and 9 pin DSUB male 2 2 3 RS232 RS232 male 9 pin DSUB e Pin 1 NC not connected e Pin 2 RD input receive data e Pin 3 TD output transmit data 12 e Pin4 DTR output data terminal ready e Pin 5 GND ground e Pin 6 DSR input data set ready e Pin 7 RTS output request to send e Pin 8 CTS input clear to send e Pin 9 NC not connected The model is designed to operate as a DTE Data Terminal Equipment When connecting the Serial Port Adapter to a DCE Data Communication Equipment e g a modem a regular modem cable straight cable shall be used When connecting the Serial Port Adapter to another DTE e g a PC a crossover serial cable must be used The crossover cable must have TD and RD crossed pins 2 3 and 3 2 RTS and CTS crossed pins 7 8 and 8 7 and optionally DTR and DSR crossed pins 4 6 and 6 4 RD 2 T RD 2 TD 3 TD 3 DTR 4 DTR 4 GND 5 GND 5 DSR 6 DSR 6 RTS 7 RTS 7 CTS 8 a EN CTS 8 Picture 6 Crossover cable RD 2 70 2 703 RD 3 DTR 4 _ DSR 4 GND 5 GND 5 DSR 6 lt DTR 6 RTS 7 _ CTS 7 CTS 8 lt _ RTS 8 Serial Port Adapter DTE Host System DTE Serial Port Adapter DTE Host System DCE Picture 7 Straight cable 2 2 4 Buttons and LED If the
16. ons e The OEM Serial Port Adapter Electrical amp Mechanical Datasheets contains important information about the OEM Serial Port Adapter Read this document if you are using the OEM Serial Port Adapter e The Bluetooth Enabler Development Kit is required when using the ECI functionality embedded in the Serial Port Adapter only available on OEMSPA333i x and RSPA3335 o The ECI Protocol Specification contains detailed descriptions of the ECI protocol Serial Port Adapter AT Commands OEM Serial Port Adapter Electrical amp Mechanical Datasheet Serial Port Adapter Product Guide Bluetooth Enabler Development Kit ECI Driver with connectBlue ECI Protocol Specification Extensions User Manual Picture 1 Serial Port Adapter documents 1 2 What is Bluetooth Wireless Technology Bluetooth allows compatible portable and stationary communications devices to communicate without using cables The technology is based on a radio link that offers fast and reliable transmission of voice and data information It doesn t require a line of sight connection in order to establish and maintain communication The Bluetooth wireless technology uses a globally available frequency range intended to ensure communication compatibility worldwide Bluetooth 15 available in mobile phones laptops handheld computers industrial devices cars and more 1 3 How can 1 use my Serial Port Adapter Your Serial Port Adapter commun
17. ort Adapter 333s must only be used with the antenna provided with the product Using another antenna will violate the regulatory type approval The product cannot be mounted inside a shielded enclosure 14 2 3 2 Power Supply The product shall have a power supply of 8 30 VDC 1 W on pin 1 and 2 on the power connector Use a female power connector 712 series from Binder Picture 9 DSUB serial connector male 2 3 3 RS232 This model supports RS232 with a male 9 pin DSUB Pin 1 NC not connected Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 RD input receive data TD output transmit data DTR output data terminal ready GND ground DSR input data set ready RTS output request to send CTS input clear to send NC not connected The model is designed to operate as a DTE Data Terminal Equipment When connecting the Serial Port Adapter to a DCE Data Communication Equipment e g a modem a regular modem cable straight cable shall be used When connecting the Serial Port Adapter to another DTE e g a PC a crossover serial cable must be used The crossover cable must have TD and RD crossed pins 2 3 and 3 2 RTS and CTS crossed pins 7 8 and 8 7 and optionally DTR and DSR crossed pins 4 6 and 6 4 15 RD 2 SE See RD 2 TD 3 TD 3 ir E S f D DTR 4 DTR 4 a S bal 2 GND 5 GND 5 DSR 6
18. the user s authority to operate the equipment 21 3 2 Declaration of Conformity CEO We connectBlue AB of Norra Vallgatan 64 3V SE 211 22 Malm Sweden declare under our sole responsibility that our products cB RSPA333s cB 0144 cB SPA312i cB 0090 to which this declaration relates conforms to the following product specifications R amp TTE Directive 1999 5 EC EN 300 328 V1 7 1 2006 05 EMC EN 301 489 1 V1 8 1 2008 04 EN 301 489 17 V1 2 1 2002 08 EN 61000 6 2 2005 Safety Compliance EN 60950 1 2001 and or IEC 60950 1 2001 1 Edition EN 60950 1 A11 2004 Corrigendum 2004 Medical Electrical Equipment IEC 60601 1 2 2001 09 10 2009 Malm Sweden Mats Andersson CTO of connectBlue AB If an RSPA333s or SPA312i is used within EU a notification must be made to each of the national authorities responsible for radio spectrum management of the intention to place radio equipment that uses frequency bands whose use is not harmonized throughout the EU on its national market More information at Atto europa eu int comnventerprise rtte gener htm 22 4 Bluetooth Qualification All Serial Port Adapter models have been qualified according to the Bluetooth specification Module Bluetooth QDID List date specification SPA3 121 2 0 B010960 2007 01 24 RSPA333s 2 0 BO11801 2007 01 24 The following Bluetooth profiles are supported covered functionality e Generic Access Profile
19. transmitter is very low 24 When using the Serial Port Adapter you will be exposed to some of the transmitted RF energy This exposure 15 well below the prescribed limits in all national and international RF safety standards and regulations 25 5 1 3 Electronic Equipment Most modern electronic equipment for example in hospitals and cars is shielded from RF energy However certain electronic equipment is not Therefore Note This equipment emits RF energy in the ISM Industrial Scientific Medical band Please insure that all medical devices used in proximity to this device meet appropriate susceptibility specifications for this type of RF energy 5 1 4 Potentially Explosive Atmospheres Turn off your electronic device when in any area with potentially explosive atmosphere It is rare but your electronic device could generate sparks Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death Areas with a potentially explosive atmosphere are often but not always clearly marked They include fuelling areas such as petrol station below deck on boats fuel or chemical transfer or storage facilities and areas where the air contains chemicals or particles such as grain dust or metal powders 5 1 5 Power Supply The Serial Port Adapter must be supplied by a limited power source according to EN 60950 1 e Connect your power supply only to designated power sources as marked on
20. ypes of systems allowing them to communicate wirelessly with other Bluetooth products such as PC cards laptops handheld computers mobile phones and other Serial Port Adapters The Serial Port Adapter is a suitable component in new products as well as in existing products A wide range of models is available to cover a wide range of usage areas This manual covers all the boxed Serial Port Adapters from connectBlue It especially focuses on how to mount the Serial Port Adapter and how to use the connectors of the Serial Port Adapter Brief overview of the features of the different Serial Port Adapter models Serial Port Plastic housing short Adapter range 7 dBm RS232 312i DSUB internal antenna 5 VDC power supply AT command interface Rugged Metal housing IP65 Serial Port long range Adapter 20 dBm 3335 RS232 RS422 RS485 DSUB stub antenna 8 30 VDC power supply AT and ECI command interface Please read the chapter Guidelines for Efficient and Safe use before using your Serial Port Adapter 1 1 Related Documents e The Serial Port Adapter Product Guide this document contains information on how to use the Serial Port Adapter Study this document before moving on to the others e The Serial Port Adapter AT Commands document contains a description of the AT commands supported in the Serial Port Adapter It also contains information on how to use the AT commands to create Bluetooth applicati
Download Pdf Manuals
Related Search