7800S User Instructions
Contents
1. 3M Dual Airline System 3M Dual Airline Respirator Assembly User must follow Dual Airline Supplied Air Respirators User Instructions provided with the 3M Dual Airline Supplied Air Respirators Assembly of 3M Combination Dual Airline Respirator with Cartridges and or Filters The 3M front mounted SA 1600 and back mounted SA 2600 versions of the 3M dual airline breathing tubes allow use of selected NIOSH approved 3M 6000 Series Cartridges and 2000 Series Filters For the listing of approved cartridges and filters reference the NIOSH approval label included with 3M dual airline adapter kits To assemble 3M Dual Airline Combination Breathing Tubes with 3M Cartridges Filters the facepiece inhalation valves must be removed If the facepiece is to be used in air purifying mode without using the 3M SA 1600 or SA 2600 breathing tubes the inhalation valves must be replaced in the facepiece before use Using the 3M Combination Dual Airline Breathing Tubes without Cartridges and or Filters To use the 3M combination dual airline breathing tubes SA 1600 and SA 2600 without cartridges or filters attach a 3M Bayonet Cap 6880 to each outer bayonet mount on the dual airline breathing tube When used as a straight Type C continuous flow supplied air respirator the Assigned Protection Factor is 1000 times the PEL or TLV guidelines for full facepiece respirators To meet the U S National Institute for Occupational Safety and2. 7885 Lens Frame Kit 7894 Eyeglass Frame and Mount with case 7895 Speaking Diaphragm Kit includes Diaphragm Gasket Retainer Ring Tool 7899 25 Lens Cover 25 pack 7899 100 Lens Cover 100 pack 7915 Shroud TychemQC 7925 Spectacle Kit 7986 Tinted Lens Cover 25 pack 7989 Buttons 7990 Clip on Welding Shield Kit 7991 Electronic Lens Assembly 7993 Welder s Shroud Tychem is a registered trademark of DuPont CAUTION Failure to properly dispose of spent cartridges filters or respirators contaminated by hazardous materials can result in environmental harm Handling transportation and disposal of spent cartridges filters or respirators must comply with all applicable federal state and local laws and regulations 3M Filters 2000 Series and 3M Filter 7093 7093C and 3M Filter Adapter 502 3M Cartridge Filter Adapter 701 is required May also be used with 3M Adapter 502 as prefilters on 3M Cartridges 6000 Series Number 502 2071 2076HF 2078 2091 2096 2097 7093 7093C Description Filter Adapter for 3M 2000 Series or Filters 7093 7093C P95 Particulate Filter P95 Particulate Filter hydrogen fluoride with nuisance level acid gas relief i P95 Particulate Filter 3M recommended ozone protection with nuisance level organic vapor acid gas relief P100 Particulate Filter P100 Particulate Filter with nuisance level acid gas relief P100 Particulate Filter 3M recommended
3. P100 Ammonia Methylamine P100 Formaldehyde Organic Vapor P100 Multi Gas Vapor P100 Organic Vapor Acid Gas P100 Mercury Vapor Chlorine Gas P100 against the following contaminants up to ten times the permissible exposure limit when qualitatively fit tested up to fifty times the permissible exposure limit when Quantitatively Fit Tested and up to 1000 times the PEL in powered air purifying or supplied air mode Certain organic vapors Chlorine hydrogen chloride and sulfur dioxide or chlorine dioxide or hydrogen sulfide escape only Certain organic vapors chlorine hydrogen chloride and sulfur dioxide or hydrogen sulfide or hydrogen fluoride Ammonia and methylamine Formaldehyde and certain organic vapors Certain organic vapors chlorine hydrogen chloride chlorine dioxide sulfur dioxide ammonia methylamine formaldehyde hydrogen fluoride or hydrogen sulfide Mercury vapor or chlorine gas Certain organic vapors and particulates Chlorine hydrogen chloride and sulfur dioxide or chlorine dioxide or hydrogen sulfide and particulates Certain organic vapors chlorine hydrogen chloride and sulfur dioxide or hydrogen sulfide or hydrogen fluoride and particulates Ammonia and methylamine and particulates Formaldehyde and certain organic vapors and particulates Certain organic vapors chlorine hydrogen chloride chlorine dioxide sulfur dioxide hydrogen sulfide ammonia methylamine formaldehyde or hydrogen fluori
4. groove onto the plastic bar and seat the gasket 3M Inhalation Port Gaskets 7887 Remove the gaskets from each side of the facepiece Replace the gaskets if they are warped distorted cut or split Replace one gasket on each side of the facepiece Be sure the gasket is flat and seated correctly 3M Nose Cup Valves 7882 The nose cup valves are supplied as a complete 3M Nose Cup Valve Assembly 7882 Remove the nose cup valves if they become warped torn or otherwise damaged Replace the valves in the nose cup such that the post points away from the nose 3M Inhalation Port Gasket 6895 Replacement Replace if gasket is warped distorted cracked or split FOR MORE INFORMATION In United States contact Website www 3M com OccSafety Technical Assistance 1 800 243 4630 For other 3M products 1 800 3M HELPS or 1 651 737 6501 3M Occupational Health and Environmental Safety Division 3M Center Building 0235 02 W 70 St Paul MN 55144 1000 3M 2007 98 0060 0010 7 4
5. oz 30 ML household bleach in 2 gallons 7 5 L of water or other disinfectant Rinse in fresh warm water and air dry in noncontaminated atmosphere 5 Respirator components should be inspected prior to each use A respirator with any damaged or deteriorated components should be repaired or discarded before use 6 The cleaned respirator should be stored away from contaminated areas when not in use REPLACEMENT PART INSTRUCTIONS Respirator parts should be inspected prior to each use Replace worn or deteriorated parts with new parts before use 3M Lens 7884 The lens should be inspected for cracking or crazing Replace if necessary Replace as follows Remove two screws on either side of lens with a Phillips screwdriver remove the top and bottom lens frame and remove the lens To reassemble first align the center of the lens with the centerline of the facepiece The center of the lens is marked by two small lines one at the top center and second at the bottom center of the lens Place the lens into the facepiece and then reattach the lens frame Replace the two center screws and tighten 3M Exhalation Valve Cover 7918 and Exhalation Valve 7283 Remove the 3M Exhalation Valve 7918 cover by lifting out on the two top prongs on either side of the center opening and sliding down Remove the exhalation valve by grasping and pulling on the edges of the valve Replace the valve if it is warped distorted cut split or if it will not s
6. Full Facepiece Respirator 7000 Series User Instructions for 3M Silicone Small 7800S Silicone Medium 7800S Silicone Large 7800S Full Facepieces Important Keep these User Instructions for reference GENERAL SAFETY INFORMATION Intended Use The 3M Full Facepiece Respirators 7000 Series are NIOSH approved and designed to help provide respiratory protection against certain airborne contaminants when used in accordance with all use instructions and limitations and applicable safety and health regulations The 3M Full Facepiece 7000 Series meets the requirements of the ANSI Z87 1 2003 standard high impact level for face and eye protection These products help provide limited eye and face protection against flying particles NWARNING This respirator helps protect against certain airborne contaminants Misuse may result in sickness or death For proper use see supervisor or User Instructions or call 3M in U S A 1 800 243 4630 In Canada call Technical Service at 1 800 267 4414 These User Instructions provide information about facepiece use only Important information is provided in the User Instructions with each of the air filtration supplied air systems that are NIOSH certified to be used with the Full Facepiece Respirator 7000 Series Failure to follow the User Instructions for the air filtration supplied air systems being used may result in sickness or death When in supplied air mode your employer must provide brea
7. Health NIOSH requirement for minimum 4 cfm 115 lpm and maximum 15cfm 424 Ipm airflow the air control valves approved for use with the 3M 7000 Series Respirators must be operated within the supply pressure ranges and hose lengths stated in User Instructions with air regulating valves Failure to do so may result in sickness or death FITTING INSTRUCTIONS Must be followed each time respirator is worn Note Do not use with beards or other facial hair or other conditions that prevent a good seal between the face and the faceseal of the respirator Standard eyeglasses cannot be worn with full facepiece respirators If corrective eyeglasses are required a 3M Spectacle Kit must be used inside the respirator To help maintain a good seal between the face and the faceseal all hair hoods or other equipment must be kept out of respirator faceseal area at all times Note Before assigning any respirator to be worn in a contaminated area a qualitative or quantitative fit test must be performed per OSHA Standard 1910 134 or CSA Standard Z94 4 Donning Respirator Fig 10 1 Fully loosen all six head straps With one hand pull hair back out of facepiece sealing area Place chin in the respirator chin cup While holding the facepiece in place pull the head harness to back of head Fig 10 2 Pull the ends of the six straps to adjust tightness starting with the neck straps first followed by the temple straps and finally forehead straps D
8. anges and hose lengths specified in the User s Instructions F Do not use powered air purifying respirators if airflow is less than four cfm 115 lpm for tight fitting facepieces or six cfm 170 lpm for hoods and or helmets G If airflow is cut off switch to filter and or cartridge or canister and immediately exit to clean air H Follow established cartridge and canister change schedules or observe ESLI to ensure that cartridges and canisters are replaced before breakthrough occurs I Contains electrical parts which have not been evaluated as an ignition source in flammable or explosive atmospheres by MSHA NIOSH J Failure to properly use and maintain this product could result in injury or death L Follow the manufacturer s User s Instructions for changing cartridges canisters and or filters M All approved respirators shall be selected fitted used and maintained in accordance with MSHA OSHA and other applicable regulations N Never substitute modify add or omit parts Use only exact replacement parts in the configuration as specified by the manufacturer O Refer to User s Instructions and or maintenance manuals for information on use and maintenance of these respirators P NIOSH does not evaluate respirators for use as surgical masks S Special or critical User s Instructions and or use limitations apply Refer to User s Instructions before donning S Special or Critical User s Instru
9. cracks tears and dirt Examine the inhalation valves for signs of distortion cracking or tearing 2 Check that the headstraps are intact and have good elasticity ae Examine all plastic parts and gaskets for signs of cracking or fatiguing and replace if necessary 4 Remove the exhalation valve cover and examine the exhalation valve and seat for signs of dirt distortion cracks or tears 5 Replace the valve if necessary Secure the valve cover prior to use Fig 15 Examine the lens for signs of cracking or other damage Replace if necessary Straps Exhalation Valve Grill Cover Fig 15 Cleaning and Storage Cleaning is recommended after each use Do not clean respirator with solvents Cleaning with solvents may degrade some respirator components and reduce respirator effectiveness Inspect all respirator components before each use to ensure proper operating condition Failure to do so may result in sickness or death 1 Remove cartridges filters and or breathing tubes The center adapter lens and faceseal can also be removed if necessary 2 Clean facepiece excluding filters and cartridges by immersing in warm cleaning solution water temperature not to exceed 120 F 49 C and scrub with soft brush until clean Add neutral detergent if necessary Do not use cleaners containing lanolin or other oils 3 Disinfect facepiece by soaking in a solution of quaternary ammonia disinfectant or sodium hypochloride 1
10. ctions 3M Mercury Vapor Cartridges 6009 and 60929 are equipped with passive 3M End of Service Life Indicators ESLI The color change indicator must be readily visible when wearing the respirator without manipulation If you cannot readily see the ESLI do not use The mercury vapor cartridges must be discarded when the ESLI changes to the discard color found on the mercury vapor cartridge label or within 30 days of opening packaging or when ESLI becomes dirty or damaged or when odors of vapors or gases become noticeable whichever occurs first Mercury vapor has no odor To assemble 3M Dual Airline Combination Breathing Tubes with 3M Cartridges Filters the facepiece inhalation valves must be removed If the facepiece is to be used in air purifying mode without using the 3M breathing tubes SA 1600 or SA 2600 the inhalation valves must be replaced in the facepiece before use 3M Nose Cup Assembly 7881S or 7981S must be used in all Full Facepiece 7000 Series applications except for Face Mounted Power Air Purifying Systems Cartridge and Filter Selection and Approvals Before using any of these products the user must read the specific use for use limitations and warning information in the User Instructions and product packaging or call OH amp ESD Technical Service at 1 800 243 4630 In Canada call Technical Service at 1 800 267 4414 Do not exceed maximum use concentrations established by local regulatory agencies Cartri
11. de and particulates Certain organic vapors chlorine hydrogen chloride and sulfur dioxide or hydrogen sulfide 1 or hydrogen fluoride and particulates Mercury vapor or chlorine and particulates 3M recommended for use against methylbromide or radioiodine up to 5 ppm with daily cartridge replacement Note Not NIOSH approved for use against methylbromide or radioiodine 3M Responder Cartridge and Canister Number 450 02 11R06 CP3N Canister FR 64 Product Name Description Alpha chloroacetophenone CN ortho chlorobenzylidene malonitrile CS and P100 Cartridge Certain organic vapors chlorine hydrogen chloride chlorine dioxide sulfur dioxide ammonia methylamine formaldehyde hydrogen fluoride hydrogen sulfide alpha chloroacetophenone CN ortho chlorobenzylidene malonitrile CS or phosphine and P100 Service Life of Chemical Cartridges and Filters 3M Chemical Cartridges 6000 Series should be used before the expiration date on cartridge packaging The useful service life of these cartridges will depend upon activity of wearer breathing rate specific type volatility and concentration of contaminants and environmental conditions such as humidity pressure and temperature Cartridges must be replaced in accordance with an established change schedule regulations or earlier if smell taste or irritation from contaminants is detected Filters must be replaced if they become damaged soiled or if a
12. dges filters are approved as assemblies for use with 3M facepieces 7800S S 7800S M or 7800S L For NIOSH approval refer to NIOSH approval label packaged with facepiece LIST OF PRODUCTS 3M 7800S Full Facepiece Respirator Parts Filters Chemical Cartridges or Airline Accessories 3M Facepiece Facepieces do not include filters chemical cartridges retainers or airline accessories Number Description Button Color 7989 7800S S silicone small red 7800S M silicone medium yellow 7800S L silicone large green Number Description 7884 a Lens 7914 b Band Clamp 7916 c Breathing Room Assembly 7999 d Air Inlet Gasket 7890 e Full Face Plug 7283 f Exhalation Valve 7918 g Exhalation Valve Cover 7893S h Head Strap Assembly Silicone 7886 i Removable DIN Connector 7887 Qj Inhalation Port Gasket 701 k Cartridge Filter Adapter for 3M Cartridges 6000 Series or 3M 2000 Series Filters 6895 1 Inhalation Gasket included in 701 m 3M Filters 2000 Series n 3M Cartridge 6000 Series 7881S 0 Nose Cup Assembly Silicone includes Nose Cup Valve Assembly 7882 or 7981S Nose Cup Assembly Silicone Small includes Nose Cup Valve Assembly 7882 3M Accessories and Parts Number Description Not Pictured 601 Fit Test Adapter for quantitative fit testing with 3M P100 Filters 2091 or 7093 7282 Inhalation Valve 7882 Nose Cup Valve Assembly 7883 Neckstrap Assembly
13. e cartridge filter adapter 701 is used the bayonet style filters cartridges can be attached directly to the facepiece 3M 2000 Series and 3M Filters 7093 7093C 3M Filters 2000 Series and 3M P100 Filter 7093 7093C can be attached directly to the cartridge filter adapters 701 1 Align opening of filter with filter attachment on facepiece 2 Turn filter clockwise until it is firmly seated and cannot be further turned Fig 1 3 Repeat for second filter 3M Cartridges 6000 Series 3M Cartridges 6000 Series can be attached directly to the 3M Cartridge Filter Adapters 701 1 Align the cartridge notch with the small solid bayonet lug on facepiece and push together Turn cartridge clockwise to stop 1 4 turn Repeat with second cartridge Fig 2 and 3 Loosen the adapter nuts and position cartridge to desired location Hold cartridge in place and tighten nuts ne Qu Note If 3M Mercury Vapor Cartridges 6009 or 60929 are being used position the cartridge at the location that allows the greatest visibility of the ESLI If the wearer cannot see the ESLI do not use for Mercury Vapor exposures Filter Assembly for 3M Filters 5N11 and 5P71 1 Place filter into 3M Retainer 501 so printed side of filter faces the cartridge 2 Press cartridge into filter retainer It should snap securely into filter retainer When correctly installed filter should completely cover face of cartridge Fig 4 3 To rep
14. eal tightly on the valve seat Replace by pushing the valve onto the exhalation valve post 3M Speaking Diaphragm Kit 7895 Remove the nose cup Using the diaphragm removal tool turn diaphragm retaining ring counter clockwise and remove Push diaphragm assembly out of the facepiece from underneath using the eraser end of a pencil or a similar object Check the speaking diaphragm gasket for damage or deformation To replace the diaphragm follow the steps in reverse Note The grill pattern with deep indentation in the center should be visible from inside the respirator 3M Removable DIN Connector 7886 Hold the inside part of the connector secure grasp the outside of the connector and twist counter clockwise to remove To replace the connector press the inner section into the facepiece until the end of the threads are flush with the facepiece exterior then screw on the outer piece by turning clockwise 3M Inhalation Valves 7282 Grasp the edges of the valve and pull away from the plastic post Replace if the valve is distorted cut split or cannot be sealed on the valve seat If the valve seat is damaged replace the removable DIN connector 7886 3M Air Inlet Gasket 7999 Remove the gasket from the air inlet opening base Replace the gasket if it is warped distorted cut split or cannot be reassembled into the air inlet To replace position the gasket so the small cut out on the gasket is pointing toward the lens Push the gasket
15. ir Systems Your employer must provide breathing air that meets at least the requirements of the specification for Grade D breathing air as described in the Compressed Gas Association Commodity Specification G 7 1 1997 in the United States In Canada breathing air systems must be supplied with air which meets at least the requirements of CSA Standard Z180 1 Failure to do so may result in sickness or death 3M Airline Air Purifying Assembly If required attach 3M Cartridges Filters 2000 or 6000 Series according to previous instructions If cartridges filters are not required remove Adapters 701 Screw 3M Full Face Plugs 7890 into both sides of the facepiece 3M Breathing Tube Assembly W 3188 1 Remove 3M Full Face Plug 7890 and screw in 3M Adapter W 3187 into center opening Fig 7 Fig 7 Fig 8 2 Connect 3M Breathing Tube W 3188 to adapter Fig 8 3 Connect 3M Breathing Tube W 3188 to air regulator valve Fig 8 4 Check all attachments for secureness See User Instructions included with air regulating valves for further information 3M Breathing Tube Assembly W 3264 1 Remove Full Face Plug 7890 and screw in 3M Breathing Adapter Tube W 3264 into center opening Fig 9 2 Fig 9 2 Connect the other end of breathing tube to air regulating valve 3 Check all attachments for secureness prior to each use See User Instructions included with air regulating valves for further information
16. lace filter remove retainer by lifting on TAB A WARNING Use product before expiration date This respiratce helps protect aganst certain arbome contaminants Misuse may vctons ask death For proper ese see Fig 4 3M Filter Adapter 502 Assembly and Filter Attachment 1 Align adapter over cartridge Engage front snap by squeezing front of cartridge and adapter together placing thumbs of both hands over top of adapter and fingers along bottom sides of cartridge Fig 5 2 Engage back snap by squeezing back side of cartridge and adapter together using the same hand positions An audible click should be heard as each snap is engaged Fig 6 3 Place filter onto the filter holder so that filter comes into even contact with gasket Twist clockwise a quarter turn until it is firmly seated and filter cannot be turned further Repeat for second filter Note The 3M Filter Adapter 502 once installed on a 3M Cartridge 6000 Series is not to be removed or reused Removal or reuse may result in leakage overexposure sickness or death Fig 6 3M 2000 Series and Filters 7093 7093C with 3M Filter Adapter 502 Place filter onto the filter holder so that filter comes into even contact with gasket Twist clockwise one quarter turn until it is firmly seated and filter cannot be turned further Repeat for second filter Note The 3M Filter Adapter 502 once installed on a 3M Cartridge 6000 Series is not to be remo
17. lapse slightly and pull closer to your face with no leaks between the face and the facepiece a proper seal has been obtained If faceseal air leakage is detected reposition respirator on face and or readjust tension of straps to eliminate the leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor Negative Pressure User Seal Check with Dual Airline Center Mounted Airline and Pressure Demand 1 2 Disconnect airline hose from air control valve With breathing tube still connected to respirator and the air control valve inhale gently If you feel facepiece collapse slightly and pull closer to your face with no leaks between the face and facepiece a proper seal has been obtained For Combination Dual Airline where cartridges or filters are attached perform user seal check as described above under the appropriate cartridge or filter that is being used If faceseal air leakage is detected reposition the respirator on your face and or readjust the tension of the straps to eliminate the leakage and recheck seal If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor RESPIRATOR REMOVAL 1 2 Fully loosen all six head straps by lifting up on buckles Remove respirator by pulling straps over head Fig 13 Fig 14 FIT TESTING The effectiveness of a respirator will be reduced if it is not fit tested properly Therefore either qualitative or quantitati
18. ll closer to your face with no leaks between the face and facepiece a proper seal has been obtained Fig 14 2 Iffaceseal air leakage is detected reposition respirator on face and or readjust tension of straps to eliminate the leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor 3M Filter 7093 7093C 1 Using both hands press or squeeze filter covers toward facepiece and inhale gently If you feel facepiece collapse slightly and pull closer to your face with no leaks between the face and facepiece a proper seal has been obtained 2 Iffaceseal air leakage is detected reposition the respirator on your face and or readjust the tension of the straps to eliminate the leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor 3M GVP PAPR 1 Place the palm of the hand over the breathing tube opening 2 Inhale gently If you feel the facepiece collapse slightly and pull closer to your face with no leaks between the face and the facepiece a proper seal has been obtained 3 If faceseal air leakage is detected reposition respirator on face and or readjust tension of straps to eliminate air leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor 3M Powerflow PAPR and Canister Cartridge 1 Place palms of hands over the air inlet of the cartridge canister Inhale gently If you feel the facepiece col
19. ll times of exposure can reduce respirator effectiveness and may result in sickness or death 2 Before using this respirator a written respiratory protection program must be implemented meeting all the requirements of OSHA 29 CFR 1910 134 such as medical evaluation training and fit testing and applicable OSHA substance specific standards In Canada follow the recommendations of CSA Z94 4 and or requirements of the applicable jurisdiction as appropriate When used in supplied air mode your employer must supply breathing air that meets at least the requirements of Grade D breathing air in Compressed Gas Association Commodity Specifications G 7 1 1997 In Canada breathing air systems must be supplied with air which meets at least the requirements of CSA Standard Z180 1 3 The airborne contaminants which can be dangerous to your health include those that are so small you may not be able to see or smell them 4 Leave the contaminated area immediately and contact supervisor if you smell or taste contaminants or if dizziness irritation or other distress occurs 5 Store respirator away from contaminated areas when not in use 6 Dispose of used product in accordance with applicable regulations Use Limitations 1 This respirator does not supply oxygen when used in air purifying mode Do not use in atmospheres containing less than 19 5 oxygen 2 Do not use when concentrations of contaminants are immediately dangerous to life or health are u
20. n increase in breathing resistance occurs N series filters should not be used in environments containing oils R series filters may be limited to 8 hours of continuous or intermittent use if oil aerosols are present In environments containing only oil aerosols P series filters should be replaced after 40 hours of use or 30 days whichever is first ASSEMBLY INSTRUCTIONS The 3M 7800S can be used in many different configurations It can be used as a positive or negative pressure air purifying respirator or in systems that are air supplied The following assembly instructions include negative pressure air purifying air supplied or combinations of both air supplied and air purifying Separate assembly instructions are required for assembly in powered air purifying systems PAPR and supplied air systems These assembly instructions are included with the powered air purifying systems PAPR and supplied air systems Powered Air Purifying Respirator PAPR 3M GVP Belt Mounted PAPR with 3M Breathing Tube GVP 123 3M Powerflow Face Mounted PAPR Supplied Air Respirator SAR 3M Dual Airline 3M Air Control Devices Continuous Flow Negative Pressure 3M Responder Cartridge FR 64 and CP3N Canister Front Mounted 3M 2000 Series and Filters 7093 7093C and Cartridges 6000 Series Side Mounted 3M Air Purifying Assembly The facepiece is pre assembled with 3M Cartridge Filter Adapters 701 When th
21. nknown or when concentrations exceed 10 times the permissible exposure limit PEL in air purifying mode when qualitatively fit tested 50 times the PEL in air purifying mode when quantitatively fit tested 1000 times the PEL in powered air purifying or supplied air mode or according to specific OSHA standards or applicable government regulations whichever is lower 3 Do not alter abuse or misuse this respirator 4 Do not use with beards or other facial hair or other conditions that prevent a good seal between the face and the faceseal of the respirator Time Use Limitations 1 Ifrespirator becomes damaged leave the contaminated area immediately and repair or replace the respirator 2 Replace filters in accordance with the filter Time Use Limitation See filter User Instructions 3 Replace cartridges in accordance with an established change schedule or earlier if smell taste or irritation from contaminants is detected NIOSH Cautions and Limitations The following restrictions may apply See NIOSH approval label A Not for use in atmospheres containing less than 19 5 percent oxygen B Not for use in atmospheres immediately dangerous to life or health C Do not exceed maximum use concentrations established by regulatory standards D Air line respirators can be used only when the respirators are supplied with respirable air meeting the requirements of CGA G 7 1 Grade D or higher quality E Use only the pressure r
22. o not overtighten the headstraps Fig 11 3 Perform a positive and or negative pressure user seal check each time the respirator is donned User Seal Checks Always check the seal of the respirator on your face before entering a contaminated area Positive Pressure User Seal Check 1 Place the palm of the hand over the exhalation valve cover and exhale gently Fig 12 2 Ifthe facepiece bulges slightly and no air leaks are detected between the face and facepiece a proper seal has been obtained 3 If air leakage is detected reposition respirator on face and or readjust tension of straps to eliminate the leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor Negative Pressure User Seal Checks 3M Cartridges Filters 6000 Series 1 Place palms of hands to cover face of cartridge or open area of filter retainers and inhale gently If you feel facepiece collapse slightly and pull closer to your face with no leaks between the face and facepiece a proper seal has been obtained Fig 13 2 Iffaceseal air leakage is detected reposition respirator on face and or readjust tension of straps to eliminate the leakage If you cannot achieve a proper seal DO NOT enter contaminated area See your supervisor 3M Filters 2000 Series 1 Place your thumbs onto the center portion of the filters restricting airflow through filters and inhale gently If you feel facepiece collapse slightly and pu
23. ozone protection with nuisance level organic vapor relief gt P100 Particulate Filter P100 Particulate Filter hydrogen fluoride with nuisance level organic vapor acid gas relief 1 f 3M recommended for relief against nuisance levels of acid gas or organic vapors Nuisance levels refers to concentrations not exceeding OSHA PEL or applicable exposure limits whichever is lower Do not use for respiratory protection against acid gas organic vapor 5 3M recommended for ozone protection up to 10 times the OSHA PEL or applicable government occupational exposure limits whichever is lower Note Not NIOSH approved for use against ozone 3M particulate filters should be changed when increased breathing resistance is noticed 3M Filters and Retainer Use with 3M Cartridges 6000 Series and 3M Filter Retainer 501 Number 501 5N11 5P71 Description Filter Retainer for 3M Filters SN11 and 5P71 N95 Particulate Filter P95 Particulate Filter 3M Cartridges 6000 Series 3M cartridge filter adapter 701 is required Number Description NIOSH Approval for respiratory protection 6001 6002 6003 6004 6005 6006 6009 60921 60922 60923 60924 60925 60926 60928 60929 Organic Vapor Acid Gas Organic Vapor Acid Gas Ammonia and Methylamine Formaldehyde and Organic Vapor Multi Gas and Vapor Mercury Vapor Chlorine Gas Organic Vapor P100 Acid Gas P100 Organic Vapor Acid Gas
24. thing air that meets at least the requirements of the specification for Grade D breathing air as described in the Compressed Gas Association Commodity Specification G 7 1 1997 in the United States In Canada breathing air systems must be supplied with air which meets at least the requirements of CSA Standard Z180 1 Failure to do so may result in sickness or death CAUTION This product contains natural rubber latex which may cause an allergic reaction USE INSTRUCTIONS AND LIMITATIONS Important Before use the wearer must read and understand these User Instructions Keep these User Instructions for reference Use For Respiratory protection from certain airborne contaminants according to NIOSH approvals OSHA limitations in Canada CSA standard Z94 4 requirements other applicable regulations and 3M instructions Do Not Use For Concentrations of contaminants which are immediately dangerous to life or health are unknown or when concentrations exceed 10 times the permissible exposure limit PEL in air purifying mode when qualitatively fit tested 50 times the PEL in air purifying mode when quantitatively fit tested 1000 times the PEL in powered air purifying or supplied air mode or according to specific OSHA standards or applicable government regulations whichever is lower Use Instructions 1 Failure to follow all instructions and limitations on the use of this respirator and or failure to wear this respirator during a
25. ve fit testing must be conducted prior to the respirator being used Note Fit testing is both a U S Occupational Safety and Health Administration OSHA and Canadian requirement Quantitative Fit Testing QNFT can be conducted using a 3M Fit Test Adapter 601 and 42 CFR 84 P100 filters such as the 3M P100 Particulate Filters 2091 or 7093 Qualitative Fit Testing QLFT with the 3M Qualitative Fit Test Apparatus FT 10 or FT 30 can be conducted using any of the NIOSH approved 42 CFR 84 Particulate filters Fit testing should be conducted using the heaviest cartridge canister filter or combination that each wearer will use in their work environment Respirators should also be fit tested while wearing any personal protective equipment PPE the wearer may use in their work environment that may affect the fit of the respirator e g hoods hardhats safety glasses hearing protections etc Note For further information concerning fit testing contact 3M OH amp ESD Technical Service at 1 800 243 4630 or a 3M location in your region In Canada call Technical Service at 1 800 267 4414 INSPECTION CLEANING AND STORAGE Inspection Procedure This respirator must be inspected before each use to ensure it is in good operating condition Any damaged or defective parts must be replaced before use Do not enter a contaminated area with damaged or defective parts The following procedure can be used as a guideline 1 Check the faceseal for
26. ved or reused Removal or reuse may result in leakage overexposure sickness or death 3M Responder Cartridge and Canister Assembly Important User Instructions on proper use and use limitations are included with the 3M CP3N Canister 450 02 11R06 and 3M Cartridge FR 64 Remove Cartridge Filter Adapters 701 from facepiece Before installing the canister cartridge check that the gasket is in place and in good condition Screw the responder canister cartridge into the DIN Port Adapter and tighten with moderate hand pressure In the remaining inlets ensure that gaskets have been properly installed and are not warped or torn Securely fasten 3M Plugs 7890 on top of the gaskets 3M GVP PAPR Assembly Screw 3M breathing tube GVP 123 elbow into center DIN port on facepiece User must follow User Instructions provided with GVP PAPR assembly 3M Powerflow PAPR Assembly User must follow User Instructions provided with Powerflow PAPR The Powerflow PAPR systems are NOT NIOSH approved for use with a nose cup Do not use a nose cup Use of a nose cup may result in sickness or death The connection between the Powerflow PAPR and the 7800S facepiece must be checked every time the unit is assembled or swiveled This check should be performed outside the contaminated environment Entering the contaminated area while the connection between the PAPR assembly and the facepiece is loose may result in sickness or death 3M Supplied A
Download Pdf Manuals
Related Search