WAVE Cabinet 20/50 100-120 V - GE Healthcare Life Sciences
Contents
1. The main switch is located in the far lower left corner seen from the front under a protective cover Below the switch there is an automatic fuse set for 15 Amps The main switch with fuse is small and can easily be overseen If the cabinet appears to be out of power even when the mains cable is connected to live power check this switch and its automatic fuse To reset the automatic fuse push the black fuse knob There is also a similar switch with automatic fuse on the top shelf WAVE Cabinet 20 50 User Manual 28 9651 84 AA 9 2 Product description Computer connections Ethernet can only be connected to one control unit as delivered To connect several control units an Ethernet switch or router is required This must be provided by the customer The dataport serial port Modbus can be connected to several WAVE instruments in series for further information see the manual for the respective instrument 10 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 3 Safety precautions 3 Safety precautions WARNING Do not operate the WAVE Cabinet in any other way than described in the WAVE Cabinet manual WARNING Protective ground The WAVE Cabinet must always be connected to a grounded power outlet WARNING Access to power cord The power cord must always be easy to disconnect WARNING Tip Hazard The shelf locks must be locked when instruments are placed on the shelves WARNING Tip haza2. if not avoided could result in death or serious injury It is important not to proceed until all stated conditions are met and clearly understood WAVE Cabinet 20 50 User Manual 28 9651 84 AA 5 1 Important user information Cautions CAUTION CAUTION indicates a hazardous situation which if not avoided could result in minor or moderate injury It is important not to proceed until all stated conditions are met and clearly understood Notices NOTICE gt NOTICE indicates instructions that must be followed to avoid damage to the product or other equipment Notes and tips Note A Note is used to indicate information that is important for trouble free and optimal use of the product TIP A tip contains useful information that can improve or optimize your procedures Typographical conventions Software items are identified in the text by bold italic text A colon separates menu levels thus File Open refers to the Open command in the File menu Hardware items are identified in the text by bold text e g Power switch 6 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 2 Product description 2 Product description Illustration Description Front door Switch for the top shelf with automatic fuse Top shelf power strip Top shelf for 1 to 3 WAVE control units 3 extendable shelves for WAVE Bioreactor units Main switch for the cabinet with automatic fuse Cabin
3. 84 AA 17 4 Installation 4 2 Placing WAVE control units in the cabinet 4 2 Placing WAVE control units in the cabinet Introduction This section describes how to install WAVEPOD control units in the WAVE Cabinet Other small WAVE control units for example CO2MIX20 can be installed in a similar way WARNING Disconnect power Always disconnect power from the instrument before performing any installation or maintenance task Instruction Follow this sequence to place WAVE control units on the top shelf Step Action 1 Lift the first WAVE control unit onto the top shelf 2 Orient the unit so that the attachment points on the side are easily accessed 18 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 4 Installation 4 2 Placing WAVE control units in the cabinet Step Action 3 Attach all hoses and cables according to the manual for the WAVE control unit 4 Move the unit as far as possible to the side to make room for subsequent units Make sure the rubber feet are not pushed over the shelf edge 5 Continue to place the subsequent units following the sequence described in step 1 4 6 When all up to three control units have been placed and connected arrange them so that the space between them is as evenly distributed as possible Make sure that no cables or hoses are stressed and that hoses are not blocked due to sharp bends Y Connect the power cord to a power outlet with correct volt
4. Action 4 16 Push the shelf back to its innermost position and make sure that the locks are engaged Open the rear door Access the WAVE Bioreactor unit from the rear and pull it towards you and to the right until its rubber feet are positioned in the corners of the guiding rails as shown in the figure Mount the top tray and connect all its hoses according to the manual for the instrument Extend and push back the shelf with the placed WAVE Bioreactor unit making sure that all hoses and cables are routed so that stress and blocking are avoided NOTICE Avoid stress and blocking It is important that the in strument cables and hoses are positioned so that stress and blocking are avoided WAVE Cabinet 20 50 User Manual 28 9651 84 AA 4 Installation 4 1 Placing WAVE Bioreactor units in the cabinet Step Action 9 Lock the shelf locks WARNING Tip Hazard The shelf locks must be locked when instru ments are placed on the shelves 10 The WAVE Bioreactor is ready It is now possible to connect the power and turn on the instrument Connect the power cord to a power outlet with correct voltage WARNING Protective ground The WAVE Cabinet must always be connected to a grounded power outlet WARNING Access to power cord The power cord must always be easy to disconnect 14 Make sure that the wheels are locked WAVE Cabinet 20 50 User Manual 28 9651
5. GE Healthcare WAVE Cabinet 20 50 100 120 V User Manual Table of Contents Table of Contents L Important user Hormation anne 5 2 Product description oocmooonconnnonnconnnonnnonnncnnoconnconnncnn nono nconcnonnnononononconcconncononos 7 A A AA 11 A A RETTET 13 4 1 Placing WAVE Bioreactor units in the cabinet uessesenenneeneennne 14 42 Placing WAVE control units in the COIN CT ae 18 Sy BSP at 20 6 Maintenance and service nennen 21 7 Techhle lspectic tions iciicccsessictemininincmaiunnnenununnsmnmunienianerd 22 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 3 1 Important user information 1 Important user information Read this before using WAVE an Cabinet All users must read the safety instructions in the WAVE Cabinet User Documentation to fully understand the safe use of the WAVE Cabinet before installing using or performing maintenance Do not operate the WAVE Cabinet in any other way than described in the user documentation If you do you may be exposed to hazards that can lead to personal injury and you may cause damage to the equipment Intended use The WAVE Cabinet has been designed to contain BASE20 50 WAVE Bioreactor instruments and WAVE control units Safety notices This user documentation contains WARNINGS CAUTIONS and NOTICES concerning the safe use of the product See definitions below Warnings WARNING WARNING indicates a hazardous situation which
6. age WARNING Protective ground The WAVE Cabinet must always be connected to a grounded power outlet WARNING Access to power cord The power cord must always be easy to disconnect 8 Make sure that the wheels are locked WAVE Cabinet 20 50 User Manual 28 9651 84 AA 19 5 Operation 5 Operation Operation For information on operation see the manuals for the respective WAVE instrument 20 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 6 Maintenance and service 6 Maintenance and service Cleaning Keep the WAVE Cabinet dry and clean Use appropriate cleaning detergent on the stainless steel surfaces of the WAVE Cabinet Take great care not to spill anything on the movable parts of the shelves or on any electrical equipment Service Contact GE Healthcare if service is required See the back of this manual for contact information WAVE Cabinet 20 50 User Manual 28 9651 84 AA 21 7 Technical specifications 7 Technical specifications 22 Parameter Electrical power Dimensions H x W x D Value 100 to 120 V 50 to 60 Hz 15 A 2082 x 1016 x 790 mm Weight 296 kg Ambient temperature 4 to 30 C Placement Stable leveled floor Relative humidity tolerance 20 to 95 non condensing Max pressure air inlet 0 2 bar Max pressure CO O inlet 1 bar WAVE Cabinet 20 50 User Manual 28 9651 84 AA For local office contact i
7. before starting assembly and installation Document any damage and contact your local GE Healthcare representative WAVE Cabinet 20 50 User Manual 28 9651 84 AA 13 4 Installation 4 1 Placing WAVE Bioreactor units in the cabinet 4 1 Placing WAVE Bioreactor units in the cabinet Introduction When WAVE Bioreactor units are placed in the cabinet the top tray should not be attached First place the WAVE Bioreactor unit see instruction below then attach the tray with connections WARNING Disconnect power Always disconnect power from the instrument before performing any installation or maintenance task WARNING Heavy object Two people are required to lift a WAVE Bioreactor unit safely into the WAVE Cabinet 14 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 4 Installation 4 1 Placing WAVE Bioreactor units in the cabinet Instruction Follow this sequence to place WAVE Bioreactor units on the shelves Step Action 1 Release the locks for the selected shelf and extend the shelf to its outermost position 2 Lift the WAVE Bioreactor unit onto the shelf well in front of the guiding rails 3 Connect all hosing and cables to the WAVE Bioreactor unit Make sure that they are routed so that they will not be stressed or blocked independently of the shelf position WAVE Cabinet 20 50 User Manual 28 9651 84 AA 15 4 Installation 4 1 Placing WAVE Bioreactor units in the cabinet Step
8. et power strip WAVE Cabinet 20 50 User Manual 28 9651 84 AA 7 2 Product description 7 gt 9 gt 4 N Pa ia Description Back door Ethernet connection Dataport connection Air inlet CO 0 inlet Cylindrical apertures to lead hoses through 8 Wheels with lock function 4 Power cord Vents 3 Hose connections The cylindrical apertures on the sides are intended for external hose connections for customer applications typically harvest and feed A hose kit for mixed air is provided to allow connection from the WAVE control units to the WAVE Bioreactor units if required It is up to the customer to utilize these hoses depending on the application and WAVE control units used 8 WAVE Cabinet 20 50 User Manual 28 9651 84 AA 2 Product description A converter kit with short air in hoses is included to convert between male and female connections It should be used to connect air from WAVE Cabinet to WAVE instruments Remove the short air in hoses when no WAVE instrument is connected otherwise the hose will be open Electrical connections WARNING Protective ground The WAVE Cabinet must always be connected to a grounded power outlet WARNING Access to power cord The power cord must always be easy to disconnect WARNING Disconnect power Always disconnect power from the instrument before performing any installation or maintenance task
9. nformation visit www gelifesciences com contact GE Healthcare Bio Sciences AB Bj rkgatan 30 751 84 Uppsala Sweden www gelifesciences com wave imagination at work GE imagination at work and GE monogram are trademarks of General Electric Company wave WAVE Bioreactor and WAVEPOD are trademarks of GE Healthcare companies All third party trademarks are the property of their respective owners 2009 General Electric Company All rights reserved First published Nov 2009 All goods and services are sold subject to the terms and conditions of sale of the company within GE Healthcare which supplies them A copy of these terms and conditions is available on request Contact your local GE Healthcare representative for the most current information GE Healthcare Europe GmbH Munzinger Strasse 5 D 79111 Freiburg Germany GE Healthcare UK Limited Amersham Place Little Chalfont Buckinghamshire HP7 9NA UK GE Healthcare Bio Sciences Corp 800 Centennial Avenue P O Box 1327 Piscataway NJ 08855 1327 USA GE Healthcare Japan Corporation Sanken Bldg 3 25 1 Hyakunincho Shinjuku ku Tokyo 169 0073 Japan 28 9651 84 AA 12 2009
10. rd Only one shelf at a time should be extended WARNING Tip hazard Do not sit on the shelves or put heavy loads on the shelves WAVE Cabinet 20 50 User Manual 28 9651 84 AA 11 3 Safety precautions 12 WARNING Heavy object tip hazard When the WAVE Cabinet is installed placed lock the wheels WARNING Vents Do not block the ventilation inlets or outlets WARNING Vents Do not remove the power plugs of the two ventilation fans from the sockets WARNING Disconnect power Always disconnect power from the instrument before performing any installation or maintenance task o gt gt gt NOTICE Release door stop Make sure that the stopping device is released before attempting to close the door WAVE Cabinet 20 50 User Manual 28 9651 84 AA 4 Installation 4 Installation Any equipment connected to WAVE Cabinet must fulfill applicable standards and local regulations Site requirements Parameter Requirement Electrical power 100 to 120 V 50 to 60 Hz 15 A Ambient temperature 4 C to 30 C Placement Stable leveled floor Relative humidity tolerance 20 to 95 non condensing Transport The WAVE Cabinet can be transported shorter distances on its own wheels Unpacking Unpack the WAVE Cabinet and place it at a stable leveled location indoors Ensure that the wheels are locked Check the equipment for damage
Download Pdf Manuals
Related Search