KEYTEC User`s Manual - AV-iQ
Contents
1. 2 1 Preparation ACEeBoard is designed for easy installation The first step is to place both receivers correctly on the top of your whiteboard frame or by mounting the receivers on the flat surface ACEeBoard consists of 2 receivers connected by a cable The left receiver has two cables one Is for the USB cable to the computer and the other is a cable that connects the left receiver to the right receiver Right receiver should have only 1 cable that connects to the left receiver Please keep in mind that it will not work properly if the receivers are positioned incorrectly In order to use the full whiteboard surface as an effective working area please position each receiver on the upper left corner and upper right corner of your whiteboard frame Note The receivers should be mounted at least 1 2 5 cm above the projected image area They may need to be mounted higher when using on flat panel displays as described in 2 2 5 This device is designed to support up to 100 inches 4 3 ratio 2 2 Installation 2 2 1 For whiteboard or projection screen with thick frame mounted on the Stand or on the wall This type of whiteboard is the most common type used It is very easy to attach the receivers on the top of the whiteboard frame using the double sided tape included in the box Acrylic holder and the steel brackets are not needed for this configuration 2 2 2 For whiteboard or projection screen with a thin frame mounted o2. Press the pen tip or pen button you should hear a low beep sound which means your digital pen works properly 3 2 2 Pen tip change When pen tip is worn out it can be replaced with new one included in the package To remove Turn the pen tip to the right or the left 90 degrees and then pull it out carefully To insert Insert the pen tip into pen cage and turn it to the right or to the left 90 degrees to lock it 4 Specification Operating size Technology Device standard Resolution CPU RAM WINDOWS OS Interface Operating Temperature Humidity Storage Temperature Humidity Power source Stas Power Station oe a oe consumption Dimension Power source Power Pen consumption Dimension 120cm 200cm 100 inch Ultrasonic and infrared HID pen device About 900 DFI Sampling Valid with 0 3mm Over 1 GHz Over 512 MB Wondows XP Vista 32bit Windows 7 USB port CD ROM driver 0 40 C 20 80 RH 20 60 C 20 90 RH DC 5V USB Less 180mW W 36mm x D 33mm x H 55mm DC 4 2V bOmW W 138mm x D 16 3mm
3. surface bracket on back side of whiteboard 2 2 5 For mounting the receivers on flat panel displays Although ACEeBoard is designed for using on whiteboard or projection screen it can also be used on flat panel displays The mounting method needs to be modified due to the heat generated from the surface of flat panel displays In general the receivers need to be mounted at about 5 above the display area in order to avoid being interfered by the heat wave in front of the display You may use any proper method to raise and mount the receivers 5 above the display but KEYTEC can also supply a simple mounting fixture for this purpose You may contact us by calling 1 800 624 4289 USA or 1 972 272 7555 Int l or sending email to tech magictouch com for the information about the mounting fixture described in the following The mounting fixture is a piece of acrylic plate with mounting tapes on one side Adhere the steel bracket on one end of the acrylic plate Mount the acrylic plate to the upper corner of the monitor with the steel bracket at about 5 above the top of the monitor Adhere the receiver on the top of the steel bracket Mount the other receiver steel bracket acrylic plate on the other corner of the monitor 2 3 Operation 2 3 1 Connecting USB cable to the computer Connect USB cable from left receiver to a USB port on the computer If cable is not long enough use active USB extension cable 2 3 2 Connecting
4. KEYTEC User s Manual ACEeBoard Hardware Installation 1 Verify Components before Installation 2 Receiver Installation 2 1 Preparation 2 2 Installation 2 2 1 For whiteboard or projection screen with thick frame mounted on the Stand or on the wall 2 2 2 For whiteboard or projection screen with a thin frame mounted on the stand 2 2 3 For whiteboard or projection screen with thin frame mounted on wall 2 2 4 For mounting Receivers on the flat surface directly 2 2 5 For mounting the receivers on flat panel displays 2 3 Operation 2 3 1 Connecting USB cable to the computer 2 3 2 Connecting projector or flat panel display to the computer with VGA cable 3 Digital Pen 3 1 Button functions 3 1 1 In MINT Interactive mode 3 1 2 In Windows mode 3 2 Digital pen operation 3 2 1 It is rechargeable 3 2 2 Pen tip change 4 Specification Revision 110715 ee 0 20 1 Verify Components before Installation Before hardware installation please check if all components listed below are included in the package If you have missing items please contact your place of purchase Receiver Connection cable Recharge Cable items Quantity Left and Right 2 16 5 ft 5m 5 Software CD ncludes calibration and board software Acrylic Plates For attaching receivers on whiteboards with thin frames with stand 7 Steel Brackets For wall mounting or whiteboards with thin frames to be hung on the wall 2 Receiver Installation
5. Projector or flat panel display to the Computer with VGA cable Effective working area VGA For software installation please refer to the software installation guide 3 Digital pen charging terminal hole button Lower button Pen tip 3 1 Button Functions The digital pen has 2 buttons executing different functions depending on the working environment 3 1 1 In MINT Interactive mode Interactive whiteboard software Lower button close to pen tip executes the right click of the mouse Upper button switching eraser mode to writing mode or vice versa 3 1 2 In Window mode Lower button executes the right click of the mouse Upper button executes the window Exit when you push and hold it for a couple of seconds This function is only available when MINT control is active 3 2 Digital Pen operation 3 2 1 It is rechargeable Use the recharging cable enclosed in the package Connect the recharging cable to the end of the digital pen and then connect it to the computer through a USB port It takes about 1 hour to recharge the pen fully After it is fully charged it can last 20 hours under continuous use If the pen is idle for 20 seconds from the last click it will automatically enter sleep mode to save battery Pen will activate again by pressing any buttons or by clicking the pen 10 sec tip If LED light turns red it s the time to charge the pen vi F sleep mode working stop
6. n the stand For this type of whiteboard the width of its frame is not enough to hold receivers completely Instead it is more convenient for you to use the acrylic holder enclosed in the box Assemble the acrylic holders with the receivers as shown below and then place each receiver correctly on the left and right top corners of whiteboard frame Acrylic holder Receiver i Whiteboard Receiver Frame d Acrylic ag holder Front view 2 2 3 For whiteboard or projection screen with thin frame mounted on wall When the whiteboard frame is much narrower than the receiver it is difficult to mount the receivers on the whiteboard frame In this case you may need to use the steel brackets enclosed in the box with following steps step 1 Place receiver onto the top of the steel bracket using double sided tape step 2 Attach the steel bracket to the back side of the whiteboard gt Steel Bracket Using a screw or double sided sticky tape to fix ans eo bracket on back side of engar whiteboard Frame 2 2 4 For mounting Receivers on the flat surface directly ACEeBoard can be mounted on the flat surface directly without whiteboard as shown below step 1 Place receiver onto the top of the steel bracket using double sided tape step 2 Attach the steel bracket to the wall using screws or double sided tape Steel Bracket yam ZA Using a screw or double Flat sided sticky tape to fix gt
Download Pdf Manuals
Related Search