Home

RTA230 QSG

1. Enter your Internet account user name and password Go Next The new configuration is displayed Click Apply to confirm changes The router will restart itself to activate the new Setting You will notice all NAT or firewall settings disappear from the Advanced menu hereafter Now follow Step 2 of Section 5 Getting On line Quality of Service QoS The router allows prioritising of upstream traffic to the Internet by allowing the user to overwrite the Type of Service TOS field in the IP datagram header TOS parameters such as Precedence Delay Throughput amp Reliability are described in the RFC791 Internet Protocol specification The user specifies the traffic conditions and traffic rules The router has three queues for traffic priority high medium and low Low priority packets are not sent when there are higher priority queues When QoS is enabled a received packet has the TOS field in its header overwritten by the traffic rule subject to traffic conditions are met The router supports both Bridge layer 2 and IP layer 3 QoS The difference is how traffic conditions can be set With Bridge QoS IEEE 802 1 priorities are used as conditions for a traffic rule to apply With IP QoS it is the IP criteria defined by the user that determines the rule to apply Please refer to the User s Manual for other advanced functions Always restart the router to activate any changes to configuration Tips for security This Dyna
2. gb ADSL Router Modem Quick Setup Guide RTA230 Important This Guide is intended to get you started quickly We have made the factory default setting of this router suitable for New Zealand All you need is to follow through the steps we describe here This Guide should be read in conjunction with the RTA23x Series ADSL Router User s Manual It is provided as a PDF file on this CD To view or print the User s Manual go to the previous menu ADSL Router RTA230 and click the View User Manual button Important safety notes can be found on page II of the User s Manual Advanced users or users who have other setup preferences should also read the User s Manual If you choose to connect via the Ethernet port no driver is required If you choose to connect via the USB port you will need to load a driver A driver is only available for Windows 98 ME 2000 and XP systems The drivers are found on this CD To install a driver into Windows go to the previous menu ADSL Router RTA230 and click the Modem drivers button Notes for this page 1 In New Zealand the majority of ADSL subscribers get PPPoA service by default Your router is preset to meet this requirement If your ISP specifies the service as PPPoE an extra step is then required to configure the router in PPPoE mode Instructions will follow to take you to Section 6 Configuration for PPPoE service 2 The User s Manual available on this CD was
3. Choose Add or Edit to configure Internet connection Choose Finish to apply the changes and reboot the system ADSL S PVC Name VPI VCI Category Protocol NAT Qos WANIP ory Edit a S aE e o 100 UBR oe og on on sitar 4 iso 8D Quality of Service IGMP Proxy Tho vp indir pl adiva EYG namote marked wih q7 You onal TTT The next screen displays VPI and VCI as o and 100 Do not change these numbers Go Next Select PPPoA VC MUX or PPPoE LLC SNAP If your ISP did not specify PPPoE you can assume it is PPPoA Go Next On the next screen untick Enable NAT and tick PPP IP extension as illustrated Go Next Quick Start Status Advanced Diagnostics Management Local Network Configure Internet Connection WAN IP Settings mt Toe Enter information provided to you by your TSP to configure the WAN IP settings Lonnections ADSI IF Routing DAS Server Obtain an IP address automatically Use the following IP address Virtual Server WAN IP ddress Firewall Quality of Service Enable MAT IGMP Proxy LI Enable Qos Enabling IP QoS for a PVC can improve performance for selected classes of applicatons Please assign the priorities for varous applicatoans from the Advanced lQuaglity of Service menu Be aware that IP QoS also consumes system resources the number of created PVCs will be reduced consequently v PPP IP extension MTU 1500 default 1500 lt Back Next gt ADSL Router Quick Set up Guide
4. MAC Encapsulation Routing MER IP over ATM IPOA Bridging Encapsulation Type LLC SNAP v 3 You can enter your Internet account User Name amp Password now If you leave the space as blank you will be asked to do it later Go Next 4 Do not change the network configuration unless you are an advanced user having your own preferences Go Next 5 A summary of the configuration is displayed Check carefully that the setting is VPI VCI 0 100 Connection Type is PPPoE LLC SNAP Then click Finish to confirm the changes The router will restart itself automatically to activate the new setting ADSL Router Quick Set up Guide 6 Now follow Step 2 of Section 5 Getting On line The screen will show the changes made pppoe_o_100 has replaced the default pppoa_o_100 o b Dynalink Quick Start Status Advanced Diagnostics Management Language Connect to Internet Connect to Internet Quick Setup Your DSL router is ready to connect to ADSL Enter your SDSL user name and password then click Connect Internet Connection pppoe _O 100 I iz Total Online Time ADSL User Name user isp co nz Password ecccecce Some advanced functions of your router Firewall port forwarding DMZ amp traffic restrictions By default a preset firewall is invoked to block all incoming requests including Ping from the Internet to your private network In the reverse direction all requests sent from your network
5. address manually use 192 168 1 x x is a number between 2 and 254 Windows XP 2000 1 Go to Control Panel Network Connections Open Local Area Connections and click Properties Double click Internet Protocol TCP IP Select Use the following IP address 2 Enter 192 168 1 x x is a number you pick between 2 and 254 This is the IP address you assign to the computer Subnet Mask is 255 255 255 0 3 Enter the router s IP 192 168 1 1 as Default gateway and as Preferred DNS server If your ISP specifies DNS server addresses enter the specified addresses according to the ISP s instructions 4 Click OK to finish You have now finished with configuring your computer Windows 98 ME 1 From Control Panel double click Network Scroll down to highlight TCP IP gt your network card Click Properties 2 Select the IP Address tab Specify 192 168 1 x x is a number you pick between 2 and 254 This is the IP address you assign to the computer Subnet Mask is 255 255 255 0 Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 1 2 Subnet mask 255 255 255 0 Default gateway 192 166 1 qa DNS server address
6. automatically Use the following DNS server addresses Preferred DNS server 192 1 Be a Alterate DNS server TCP IP Properties HEI Bindings Advanced DNS Configuration Gateway WINS Configuration IP Address An IP address can be automatically assigned to this computer If your network does not automatically assign IP addresses ask your network administrator for an address and then type it in the space below C Obtain an IP address automatically Specify an IP address IP Address gh eg Bo OR Bs 4 g Dynalink 3 Select Gateway tab Enter the R BE router s IP address 192 168 1 1 Bindings Advanced Netpios Click Add If your SP specifies DNS DNS Configuration Gateway wins Configuration IP Address server addresses go to the tab The first gateway in the Installed Gateway list will be the default a 7 The address order in the list will be the order in which these DNS Configuration Enter the machines are used specified addresses according to the ISP s instructions New gateway 4 Click OK amp then OK to finish The ee Be system may ask to read the pae Windows CD and then ask to ed S restart the computer You have now finished with configuring your computer Go to Section 5 Getting On line Getting On line It takes only 2 easy steps STEP1 GOTO THE CONNECT TO INTERNET PAGE Start your web browser Enter the default address http 19
7. fine but I cannot run certain applications You need to set up virtual servers or DMZ host See Section 7 on Firewall amp traffic restrictions Qs The router s IP and or administrative password have been modified But the details have now been forgotten You can restore the router to factory default by pushing a pin into the hidden reset button located next to the power on off button at the back of the router Push and hold for 5 seconds then release to reset router Q6 I need to know the dynamically assigned WAN IP when the router goes online Go to Status gt Internet Connection the WAN IP is displayed here a pr amp o gb y ink Quick Start Status i Advanced Diagnostics Management Language Overview Internet Connection AE Current Internet connections are listed below Traffic Counters Status DHCP Table P C Name Y PI CI Category Protocol NAT WAN IP Address Onine Time Routing Table ARP Table pppoa_o 100 0 100 UBR PPPoA VC MUX On 219 988 155 211 Up 00 19 21 15 Q 7 How to get information update This Quick Guide and User s Manual on CD are the primary source of information about the product Please check the Dynalink website http www dynalink co nz regularly for updates links or to download a more current version of this Quick Set up Guide Sananiy gb Dynalink Dynalink warrants this product against defects in materials and workmanship for a period of twelve months from the original
8. for static IP DNS server IP only if specified by ISP Choose from your connection options 1 Ethernet for standalone computer Operating System independent Connect the LAN port of the router directly to the Ethernet port of your computer One Ethernet cable is provided g Dynalink 2 Ethernet for multiple computers Operating System independent This is for sharing Internet access You will need to purchase a network hub and extra Ethernet cables Using the provided Ethernet cable connect the LAN port of the router to any of the ports available on the hub Next connect each of the computers to the network hub 3 USB for standalone Windows 98 ME 2000 XP computers only Connect via Ethernet is the preferred option If your computer does not have an Ethernet port you may choose this option You must then install a driver to operate the router The drivers are found on this CD To install a driver into Windows go to the previous menu and click the Modem drivers button Connect the Router 1 Connect the DSL port of the router directly into your ADSL jackpoint telephone wall socket with the provided line cord Do not connect through a filter unless the filter has a designated MODEM port for this purpose 2 Connect the LAN port of the router and the Ethernet port of your computer using the Ethernet cable provided If you choose to connect via the USB port there is no need to use the Ethernet cable Make no USB co
9. is powered on Locate the pinhole that contains a hidden reset button next to the power on off button at the back of the router Use a Suitable tool push the hidden button and hold for 5 seconds Release button and the router will reboot to load the factory default Troubleshooting Q1 Cannot open the Router control panel from my browser 1 Check that the router s LAN or USB light is on If not check your Ethernet or USB cable 2 Perform a PING test Go to Start Programs MS DOS Command Prompt In Windows XP or 2000 you may click Start Run Enter cmd then OK Type ping 192 168 1 1 then press Enter The response should be Pinging 192 168 1 1 with 32 bytes of data Reply from 192 168 1 1 bytes 32 time 4ms TTL 30 If you see a similar response the router is communicating with your computer correctly and the problem lies elsewhere If the result is Request timed out or similar failures there may be a networking problem Check that the LAN or USB cable is firmly plugged in 3 Disable any personal firewall or virus checker temporarily If you are using Internet Explorer go to Tools Internet options Security Reset security level of all 4 icons to default You can revert to your customised settings after configuring the router 4 If previously the computer had a dialup modem check browser setting For example in Internet Explorer go to Tools Internet options Connections and select Never dial a connection Also check
10. written for international users In Chapter 5 Connection Mode only references to PPPoA amp PPPoE is relevant to New Zealand users Ignore all references to the value of VPI or VCI In New Zealand VPI is o and VCI is 100 These numbers are preset as factory default Do not change or the router will not connect ge Dynalink ADSL Router Quick Set up Guide Default Configuration for New Zealand This Router is shipped with the following factory default settings Router IP address 192 168 1 1 Subnet mask 255 255 255 0 VPI O VCI 100 Connect mode PPPoA VC MUX NAT enabled DSL line mode auto select G DMT T1 413 WAN IP dynamic DHCP enabled DNS relay on UPnP IGD enabled Firewall incoming on Firewall outgoing off Router configuration amp management User name admin Password admin Telnet password admin If your ISP specifies that your ADSL service is PPPoE connect mode must be changed to PPPoE LLC SNAP Instructions will follow Check with your ISP if you are unsure of the type of service you have subscribed to Advanced users who have other setup preferences should first read the User s Manual Before you start Make sure your computer has these installed Ethernet or USB port TCP IP protocol enabled Aweb browser Internet Explorer 5 0 Netscape 6 or better Obtain your Internet account information from your ISP Login user name and password Public IP address only if you subscribe
11. 2 168 1 1 Type admin for both User name and Password See Q1in Section11 Troubleshooting PEPEE TE if you cannot get this screen i Ee Next you will be in the Quick Start gt APA Connect to Internet page DSL Router User name admin i Password Beccee Remember my password If your ISP specifies that your ADSL service is PPPoE you must now follow Section 6 to change the router s connect mode to PPPoE Check with your ISP if you are unsure of the type of service you have subscribed to ADSL Router Quick Set up Guide STEP 2 ENTER INTERNET ACCOUNT DETAILS Enter your Internet account User Name amp Password in the exact format as specified by the ISP Make sure the page displays Your DSL router is ready to connect before clicking Connect See Q2 in Section 11 Troubleshooting if after several minutes the message Your DSL router is not ready to connect still shows a yr o db Dynalink Quick Start Status Advanced Diagnostics Management Language Connect to Internet Connect to Internet Quick Setup Your DSL router is ready to connect to ADSL Enter your ADSL user name and password then click Connect Internet Connection pppoa_O_100 Total Online Time 23 secs ADSL User Name user isp co nz Password eececece Once connected the screen changes to display the on line time Click Disconnect only if you wish to disconnect manually Ee amp o Quic
12. LAN Settings that the option Use a Proxy Server is not selected 5 If the router is connected to a network hub try connecting the router directly to the computer in a standalone setup to eliminate any possible problem associated with the hub 6 The router s private IP address is 192 168 1 1 To access the browser control panel your computer must be on the same subnet as the router See also Q3 ge Dynalink Q2 Cannot connect to Internet or cannot browse 1 Check router s DSL light is on Normally it takes less than one minute to establish a link with the telephone exchange The link will establish as long as there is signal If the DSL light does not come on the router is not seeing any signal Check that ADSL service has been enabled If there is a designated ADSL jackpoint for the service make sure the router is connected directly into this jackpoint Other jackpoints cannot be used If there is no designated ADSL jackpoint any jackpoints may be used Connect the router directly into a jackpoint or through the port marked MODEM on a filter 2 If the routers DSL light is already on check if router is on line Go to the Quick Start menu as described in Section 5 Getting On line f the router reports Your DSL router is ready to connect you are not on line Make sure the user name and password have been entered in the exact format as specified by the ISP 3 Check the configuration of computer and rou
13. can freely pass through to the Internet If you want servers on your network accessible to Internet users set up port forwarding in Advanced gt Virtual Servers gt Port Forwarding Refer to Chapter 4 NAT Virtual Servers on page 43 of the User s Manual If you run applications that require unrestricted 2 way traffic between computer and the Internet set computer up as DMZ Host in Advanced gt Virtual Servers gt DMZ Host Refer to Chapter 4 NAT DMZ Host on page 45 of the User s Manual Caution any DMZ host computers are no longer protected by the firewall You can restrict Internet services to some computers on your network by setting up IP Filtering Refer to Chapter 4 Filtering by IP address on page 47 of the User s Manual IP extension bridging In IP Extension Mode the ADSL router resembles a modem Firewall protection and Internet sharing are not available The router becomes a bridge between WAN amp LAN A computer or network device connected behind it receives a public WAN IP directly This arrangement is suitable for certain applications that require a computer or network device to receive a public IP ge Dynalink To set up IP extension go to Advanced gt Internet Click on the modify icon under Edit Er ja amp oO G Dynalink Quick Start Status Advanced Diagnostics i Management Latquaqe English hea Local Network Internet Connection Configuration Internet 2
14. date of purchase We will at our discretion repair or replace the faulty unit free of charge provided it is returned to us with proof of purchase from an authorised dealer within the warranty period Return delivery after repair will be paid for by Dynalink We reserve the right not to repair or replace goods that have been mishandled abused or not installed according to the guidelines as outlined in the instructions have been subjected to a power surge from other equipment or other external factors have been altered or modified ge Dynalink Always check that your hardware is installed correctly Check our web site for the latest information and troubleshooting guide If you have difficulties contact Dynalink Technical Support for issues relating to installation and operation If possible visit Dynalink s on line support area at sJ Ie New Zealand www dynalink co nz support yw Australia www dynalink com au support Contact Dynalink s Technical Support New Zealand Australia Phone 0800 653 962 Phone 1800 653 962 Fax 0800 503 962 Fax 1800 063 962 Monday Friday 8 30am 7 30pm Monday Friday 8 30am 5 30pm NZRTA230QG 02
15. k Start Status Advanced Diagnostics Management Language English v g Dynalink Connect to Internet Connect to Internet Quick Setup Your DSL router is connected to ADSL and you can now surf the Internet Current Connection Status Online Time 13 secs Data Transmitted 816 bytes Data Received 912 bytes More details can be found in the Status menu Disconnect Your Internet account user name amp password will be saved automatically ge Dynalink Configuration for PPPoE service Follow this procedure ONLY if your ISP specifies the service as PPPoE Caution do not set your router to PPPoE mode if your ADSL service is PPPoA It will not connect Reset to factory default will restore router to PPPoA mode From the Quick Start menu click on Quick Setup to configure for PPPoE 1 Untick the Auto Scan Internet Connection box VPI and VCI shall be set to o and 100 respectively Click Next for the next page 2 Select PPP over Ethernet PPPoE Encapsulation shall be LLC SNAP as illustrated below Go to the next page change nothing and then Next a pr amp o go Dynalink Quick Start Status Advanced Diagnostics Management mirterem English Connect to Internet Configure Internet Connection Connection Type Quick Setup Select the protocol and encapsulation type over the ATM PVC that your ISP has instructed you to use Protocol PPP over ATM PPPoA PPP over Ethernet PPPoE
16. link series of Broadcom chipset powered routers are highly powerful secure and stable devices To ensure that you get the maximum benefit from your Dynalink router Dynalink makes the following strong recommendations Do Change and keep secret your router s admin user name and password This will ensure that no unauthorised changes can be made to your settings and will prevent any unauthorised changes to the embedded code A router has both a processor and memory and unauthorised access is highly undesirable Back up your router s configuration This function can be found in the router s Management gt Backup Config menu Disable UPnP if you don t need this function Go to Advanced gt Local Network gt UPnP to disable UPnP Read about the more advanced functions of this router They can be found in Chapter 4 of the User s Manual on this CD Don t ge Dynalink Enable any form of remote access to the router unless you are confident in handling the security implications Beware that an attacker may compromise the router and attempt to exploit the system without your knowledge Remote administration of the router opens up the opportunity to breach the security of your router and network Use the built in access control list to restrict access to only authorised Internet hosts Enable IP extension bridging without firewall protection If the router operating in this mode is connected to a computer t
17. nnection now During driver installation you will be advised to connect the USB port of the router to your computer 3 Connect the provided AC AC power adaptor to the PWR jack of the router Plug the adaptor into a mains power outlet Switch on the router The DIAG light will remain on for a short time indicating self check in progress Wait until the DIAG light has turned off before proceeding to the next section In normal operation these three lights shall be on PWR LAN or USB and DSL Section 9 of this Guide explains how these indicator lights work Configure your computer The description below assumes you are connecting the router via Ethernet If you are connecting the router via USB refer to Chapter 2 USB Driver Installation on page 4 of the User s Manual on CD You have two options Following option 1 is simplest This is the Windows default network setting OPTION 1 CONFIGURE COMPUTER TO GET IP ADDRESS FROM DHCP If your computer is already configured to obtain an IP address automatically from a DHCP server do nothing By default the router is a DHCP server Now go to Section 5 Getting On Line If you are unsure of your computer s network setting refer to Chapter 3 Configure PC to get IP address from DHCP on page 18 of the User s Manual ADSL Router Quick Set up Guide OPTION 2 MANUALLY ASSIGN IP ADDRESS TO COMPUTER The router s default address is 192 168 1 1 If you prefer to assign an IP
18. o the minimum use a personal firewall Software to protect the computer Send your router away for repair or replacement without resetting to factory default or wiping out your Internet account login details Use the Backup Configuration option to store your router s setting elsewhere This function can be found in the router s Management gt Backup Config menu When a replacement unit is received restore the original setting from the backup file Indicator lights There are 5 indicators on the front panel Every time the router is powered on or reset the DIAG light will come on indicating self test is in progress Indicator Status Description PWR Off Power off Solid Power on DIAG Off Power off or initial self test OK Flashing Firmware uploading or updating Solid Initial self test failed The unit is faulty LAN Off Power off or no Ethernet link is present Flashing Data is going through the Ethernet port Solid The Ethernet link is ready USB Off Off USB link not present Flashing Blinking Data is going through the USB port Solid The USB link is ready DSL Off Power off or ADSL line training is in progress Flashing Data are going through the ADSL link Solid ADSL link is ready 10 11 ADSL Router Quick Set up Guide If you need to reset the router to factory default The quickest method to restore router to its original setting is reset to factory default Make sure the router
19. ter If you still cannot browse perform a PING test as described in Q1 2 using these addresses A Ping www dynalink co nz or any valid web address B Ping 205 178 180 16 or any valid public IP address If both A amp B reported failed response such as request time out and you assigned an IP address to your computer manually Go to Procedure 2 of Section 4 Check that the router s IP 192 168 1 1 is entered as gateway amp DNS If these settings are correct ping the computer s IP eg Ping 192 168 1 2 If there is still no reply your network card may be faulty If A fails but B shows a response this is probably a DNS problem Go to Procedure 2 of Section 4 Enter the router s IP 192 168 1 1 as DNS If both A amp B show a response your router is actually on line The problem may be with your browser setting Try returning any custom Settings of the browser to default If you have a personal firewall disable it to see if it makes any difference Also you may try shutting down the computer and restarting Q3 Need to install router on a network that uses a different subnet If the existing network already has a DHCP server disconnect one computer from the network Connect the computer to the router The host computer will be assigned 192 168 1 2 You can change the router s IP so that it is consistent with the network Disable DHCP on the router ADSL Router Quick Set up Guide Q4 Browsing is

RTA230 QSG

Contents

Download Pdf Manuals

Related Search

Related Contents