Home

Configuring the SIMATIC Field PG - Internet

1. 1 Rechargeable battery The supplied rechargeable battery is installed behind a cover The rechargeable battery Lithium lon makes the device portable independent of an external power supply The battery pack also prevents data loss in case of power failure See also section 2 Memory expansion You can install memory submodules in these slots to increase main memory Maximum memory expansion 2 x 256 Mbytes Remove the cover to access the memory submodules See also section 4 1 3 Rating plate and Certificate of Authenticity The rating plate and Certificate of Authenticity with the Microsoft Windows Product Key You need this to install new software SIMATIC Field PG Manual 2 8 A5E00075760 04 Getting Familiarized with the SIMATIC Field PG 2 2 Keyboard Keyboard Layout The keyboard is split into the following areas e Alphanumeric or typewriter keyboard with special keys e Function keys e Cursor control keys Repeat Function All the keys on the keyboard are of the autorepeat type The character is repeated as long as the key is pressed Keyboard Caps The keyboard comes with international and German labeling International National Shift Z Together with Unshift ALTGR key j Together with the Fn key with Num Lock 4 without Num Lock Cursor left Fig 2 1 The Keyboard
2. ly n s GS Ga Gas GD A 0 GC Gee Ga Car WZ AD a SIMATIC Memory Card Fig 3 8 Slot for SIMATIC Memory Cards Proceed as follows when working with SIMATIC memory cards 1 Switch on your device 2 Start your SIMATIC programming function 3 Plug a SIMATIC Memory Card into the Field PG slot Correct insertion direction is soot marked on the Field PG and on the Memory Card 4 You can read program or erase the Memory Card with the programming function of your SIMATIC programming software 5 Close the programming function of your SIMATIC software 6 Remove the SIMATIC memory card from the programming port for further use in a programmable logic controller Caution You must insert the Memory Card with the type label pointing towards the rear of the unit You must not remove the SIMATIC Memory Card while the module programming status LED is lit Always discharge your body s static electricity by briefly touching a grounded part of the device before you insert a SIMATIC Memory Card SIMATIC Field PG Manual 3 16 A5E00075760 04 Configuring And Operating The SIMATIC Field PG 3 9 Working with Micro Memory Cards Working with Micro Memory Cards Read program and erase Micro Memory Cards MMC via the Micro Memory Card interface Operation
3. e e ee ee SIMATIC S5 patch cord Fig 3 11 Connecting to an S5 PLC You connect your Field PG to a SIMATIC S5 PLC as follows 1 Switch off your device Open the cover of the interface ports on the rear of the device Connect the patch cord to the COM1 V 24 Modem PLC port Secure the connector with screws oO AON Connect the patch cord to the corresponding port on the CPU of the PLC Caution The interface port may be damaged if you use the wrong patch cord SIMATIC Field PG Manual A5E00075760 04 3 19 Configuring And Operating The SIMATIC Field PG 3 12 Connecting the Field PG to a SIMATIC S7 Network MPI DP Connecting an S7 Programmable Controller via an MPI DP Interface You can use the potential separated MPI DP interface to connect the SIMATIC Field PG to a SIMATIC S7 programmable controller or to a PROFIBUS network The MPI patch cord 5m for connecting to SIMATIC S7 CPUs Order no 6ES7901 OBFO0 0AAQ0 is included in the consignment The data transfer rate is limited to 187 5 Kbit s when using this patch cord For baud rates gt 1 5 Mbit s you must use a PROFIBUS cable for 12 Mbit s Order no 6 S7901 4BD00 0XA0 For environments free MPI DP interface of
4. Configuring the SIMATIC Field PG Security Power E 35 32 09 05 2000 Disabled 10056MB None ATAPI Removable CD ROM Write Back Version ltem Specific Help lt Tab gt lt Shift Tab gt lt Enter gt selects field Example Hour Minute Second Month Day Year or Boot Options Keyboard Features Hardware Options System Memory 640 KB Extended Memory 128511 KB Fig 5 2 Main SETUP Menu Settings in the Main Menu In the Main menu you can move upwards and downwards using the cursor keys T and J to select the following system parameters System Time For viewing and setting the current time System Date Diskette A Memory Cache By submenus For viewing and setting the current date Type of built in floppy disk drive For setting the cache options Primary Master Type of built in drives Secondary Master Type of built in drives Boot Options For setting boot options Keyboard For setting keyboard interface options e g NUM Lock Typematic Features Rate Hardware Options For setting PG hardware options SIMATIC Field PG Manual A5E00075760 04 5 5 Configuring the SIMATIC Field PG System Time und System Date System Time and System Date indicate the current values Once you have selected the appropriate option you can use the and keys to modify the time setting Hour Minute Second and the date Month Day Year You can move between the entries in the date a
5. Control panel Installing Drivers and Software Installieren the drivers and software from the supplied CD Backup PG Proceed as follows 1 Insert the CD Acrobat Reader must be installed Navigate through the driver list to Drivers FieldPG pdf gt W N Install the desired driver according to the Driver List SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 8 5 Installing the Operating System Windows 2000 Do not follow these instructions unless you want to upgrade from Windows Me NT to Windows 2000 or if you want to reinstall The new installation or reinstallation of the operating system is accomplished with the Recovery CD This CD contains encoded files which can only be transferred to a SIEMENS SIMATIC programming device The transfer of information is made with the program OEMSETUP EXE on the CD ROM or after booting from the CD ROM with the recovery function The installation of the operating system via the Windows 2000 setup program is possible after transferring the necessary data to the hard disk The Windows 2000 setup starts when you enter HD gt i386 WINNT EXE HD drive on which the folder 1368 was transferred to Setup for Windows 2000 can be carried out on existing Windows installations via the program HD i386 WINNT32 EXE Windows 2000 Installation Sequence If a Windows operating system is already installed or if the programming device has been started wi
6. The CD is tested when you close the drive and the access LED on the drive flas hes to indicate that the test is in progress if the LED does not stop flashing the CD is bad but readable if the LED flashes several times and then remains on the CD is not readable and defective Caution Risk of data loss and damage to the drive Optical drives are highly sensitive to excessive vibration Vibration during opera tion can damage the drive or the CD Use the DVD ROM CD ROM drive for a burning operation in untroubled environ ment only Additional Software 2 20 To be attain the full functionality of the DVD ROM or DVD ROM CD RW drive additional software DVD player or burner software is necessary You can find it on the CD included in the delivery of the device To install the software place the CD in the drive and follow the instructions on the screen SIMATIC Field PG Manual A5E00075760 04 2 1 Getting Familiarized with the SIMATIC Field PG External Power Unit and Battery External Power Unit ZN External power supply for the SIMATIC Field PG for operation on 120 V or 230 V power supply networks The voltage range Is selected automatically With line operation the integrated battery is charged at the same time The connecting cable for the SIMATIC Field PG is installed fixed on the external power supply The external power supply is connected with a patch cord to the mains Warning The SIMATIC Field PG must
7. 3 4 COMMISSIONING 2 00 sctoney Sorabeac te dawns oe cee keke bone Aswe E i 3 8 3 4 1 Cold Start of the SIMATIC Field PG 0 0 ccc eee ee 3 8 3 4 2 Restart of the SIMATIC Field PG 0 0 cee 3 10 3 5 Pomel ICIAP G chaser dieagrace ere adres Seopa Be ea ere eee eee Bee 3 11 3 6 Connecting Peripheral Devices 0 ccc cece eee eens 3 12 3 7 Working with SIMATIC S5 Memory Submodules 00 3 8 Working with SIMATIC Memory Cards 00 c0 cee e eee eee 3 9 Working with Micro Memory Cards 00 c cece eee ees 3 17 3 10 Working with PC Cards 0 ccc teens 3 18 3 11 Connecting the Field PG to a SIMATIC S5 Network 3 19 SIMATIC Field PG Manual l A5E00075760 04 IX Contents 3 12 Connecting the Field PG to a SIMATIC S7 Network MPI DP 3 20 3 13 Networking the Field PG with Other Stations on PROFIBUS 3 22 3 14 Ethernet RJ45 Ethernet Interface 00 c eee eee 3 22 4 SIMATIC Field PG Expansions 00cc eee ee eee eee eee e eee eeneeee 4 1 Installing Memory Expansion Submodules 0000 eee 4 2 4 2 Processor WOOlade sae dh cn edhe ew iaa iaa RR et ae dbecedes eden E 4 4 4 3 Replacing Backup Battery 0 0c cece eens 4 4 5 Configuring the SIMATIC Field PG cceceececececuceceeueeuvaces 5 1 5 1 Changing the Device Configuration with SETUP 5 2 5 2 The Main Menu 0
8. 895 7001 GMT 01 00 America Johnson City Technical Support and Authorization Local time Mo Fr 8 00 to 19 00 Asia Australia Singapore Technical Support and Authorization Local time Mo Fr 8 30 to 17 30 Phone 1 423 461 2522 Phone 65 740 7000 Fax 1 423 461 2289 Fax 65 740 7001 E mail simatic hotline E mail simatic hotline sea siemens com sae siemens com sg GMT 5 00 GMT 8 00 German and English are spoken on all the SIMATIC hotlines French Italian and Spanish are also spoken on the authorization hotline yi SIMATIC Field PG Manual A5E00075760 04 Preface Service amp Support on the Internet In addition to our documentation we offer our Know how online on the internet at http www ad siemens de support where you will find the following e Current Product Information leaflets FAQs Frequently Asked Questions Downloads Tips and Tricks e A newsletter giving you the most up to date information on our products e The Knowledge Manager helps you find the documents you need e Users and specialists from all over the world share information in the forum e Your local customer service representative for Automation amp Drives in our customer service representative data bank e Information on field service repairs spare parts and more under Services SIMATIC Field PG Manual 5 A5E00075760 04 yii SIMATIC Field PG Manual A5E00075760 04 Contents PrClaC
9. A teach in cycle ensures that the battery s maximum charge capacity is at your disposal Notice There is a danger of the charge status indicator misinterpreting the actual capacity of the battery if a lengthy period of time is allowed to pass between teach in cy cles This can result in an unexpected shutdown with no prior warning Teach in Cycle calibration cycle Run a teach in cycle e Approximately every six months e if a prolonged period of time has elapsed since the battery was last used e if you think that the battery no longer operates at full capacity e if the programming device shuts down unexpectedly with no prior warning e if operating time on battery becomes shorter SIMATIC Field PG Manual 3 6 A5E00075760 04 Configuring And Operating The SIMATIC Field PG Performing a Teach in Cycle Broadly speaking the procedure for a teach in cycle is as follows 1 Power supply operation Charge the battery until it is full battery display on the device is green Duration About 3 hours for an empty battery 2 Battery operation Discharge the battery until the battery display on the device changes from orange to red To do this remove the power supply unit from the Field PG Duration approximately 2 4 hours 3 Power supply operation Charge the battery for about 30 minutes to do this connect the power supply unit again You can carry out an automatic teach in cycle with the Field PG panel see sectio
10. Do not switch off the PG during cold start Otherwise full initialization will fail Do not change the BIOS default values Startup under Windows 3 8 Once you have entered the requisite information and configured the operating system the PG is rebooted The Welcome screen helps you to get familiar with the Desktop user interface Now the user interface is displayed following system startup every time you power up or reset the PG SIMATIC Field PG Manual A5E00075760 04 Configuring And Operating The SIMATIC Field PG Default country code of the Windows 2000 menus dialogs and keyboard layout is English You can set another language and keyboard via the control panel with the dialog Start gt Settings gt Control Panel gt Regional Options gt tab General box Menus and dialogs gt tab Input locales box Input language Authorization Additional To use the SIMATIC software e g STEP 7 you have to install an authorization since it is not possible to run this protected software without authorization The authorizations can be found on the Authorization disk that comes with your PG To perform the authorization e Insert the authorization disk in drive A e Click on the Windows Start button and e select the menu command Simatic gt AuthorsW gt AuthorsW to open the authorization tool It will guide you through the installation routine of the authorization Copy the STEP 5 and STEP 7 authori
11. During a standard installation Windows 2000 is installed on drive C Therefore please make sure when selecting a drive that there is enough available memory on drive C after the data transfer 8 You can start the Windows setup after the data transfer and acknowledgment of the completion message via the program HD I386 WINNT exe HD drive on which the folder 1368 was transferred to If a Windows operating system already installed you can start the Windows 2000 setup after starting Windows via the program HD l368 WINNT32 exe Choosing the Language for Windows 2000 8 10 The Multilanguage User Interface MUI allows you to set the Windows 2000 menus and dialogs to another language In order to install the MUI run the program MUISETUP EXE in the MUI folder on the Recovery CD and follow the screen dialog to install the desired languages The desired language for Windows 2000 menus and dialogs as well as the keyboard layout can be set via the control panel with the dialog Start gt Settings gt Control Panel gt Regional Options gt tab General gt box Menus and dialogs and in the tab Inputs box Keyboard layout In addition to the language for menus and dialogs you can also set via Regional Options the standard for the region with Set Default Your device is set to English menus and dialogs and a US keyboard when delivered You can set another language and keyboard via the control panel with the dia
12. Further information on the approvals certificates and licenses for your device is provided in Chapter 1 Incorporation into the Communications Environment This manual forms part of the supplied CD Backup PG For supplementary instructions on how to handle the software please refer to the corresponding manuals for example the STEP 7 Manual SIMATIC Field PG Manual T A5E00075760 04 III Preface Structure of the Manual Chapters 1 to 5 of the manual contain the most important instructions for commissioning and using the Field PG Chapters 6 tol8 are reference sections required in special situations Important Notes This chapter contains information on security certificates guidelines and approbations Familiarizing Yourself Before you initially start using the Field PG you should inform yourself about its components and their functions in Chapter 2 Configuration and Operation Before you start to use your programming device you should read about the components and functions of the SIMATIC Field PG in Chapter LEERER MERKER Installaiion Chapter LEERER MERKER describes the basic steps necessary for commissioning the Field PG This chapter also contains instructions for working with submodules and memory cards for programmable logic controllers and additional interfaces Expansion Chapter 4 describes how to expand your SIMATIC Field PG for example installation of memory expansions Please observe the s
13. Reserved Fig 5 10 IRQ Resource Exclusion Submenu Available IRQ can be assigned by the BIOS Plug amp Play mechanism to Plug and Play modules or to basic board functions Reserved Must only be set if the respective interrupt is not to be specifically assigned to a Plug amp Play PCMCIA module SIMATIC Field PG Manual A5E00075760 04 5 15 Configuring the SIMATIC Field PG 5 4 The Security Menu You can only edit the fields enclosed in square brackets Two passwords are assigned to protect your programming device from unauthorized use You can use the supervisor password to prevent use of diskettes for the normal user and to limit use of the hard disk Main Advanced Security Power Version Item Specific Help Supervisor Password is Disabled User Password is Disabled Supervisor Password Set User Password Enter controls access to the Enterf setup utility Password on boot Disabled Fixed disk boot sector Normal Diskette access Supervisor Fig 5 11 Security Set Supervisor Pass word Menu This field opens the dialog box for entering a password Once it has been entered the supervisor password can be changed or deleted by pressing Return and thus deactivated Set User Password Password on boot Fixed disk boot sector Diskette access 5 16 This field opens the dialog box for entering a password Once it has been entered correctly the user password can
14. Setup will guide you through the installation The authorization diskette with the authorizations necessary for the use of SIMATIC software is only delivered with versions containing the corresponding SIMATIC software The installation of the authorizations is described in Section Cold Start of the PG SIMATIC Field PG Manual A5E00075760 04 Guidelines for Handling Electrostatically Sensitive Devices ESD Chapter Overview A Section Description Page A 1 What is ESD A 2 Electrostatic Charging of Persons A 3 General Protective Measures Against Electrostatic Discharge Damage SIMATIC Field PG Manual A5E00075760 04 A 1 Guidelines for Handling Electrostatically Sensitive Devices ESD A 1 Definition A 2 What is ESD All electronic modules are equipped with large scale integrated ICs or components Due to their design these electronic elements are very sensitive to overvoltages and thus to any electrostatic discharge These Electrostatically Sensitive Devices are commonly referred to by the abbreviation ESD Electrostatically sensitive devices are labeled with the following symbol Caution Electrostatically sensitive devices are subject to voltages that are far below the vol tage values that can still be perceived by human beings These voltages are pre sent if you touch a component or the electrical connections of a module without pre viously being electrostatically d
15. Timeouts and Fixed Disk Timeout or they set automatically to their defaults Major components are shut down in suspend mode The information needed for reactivating the programming device is buffered Hard Disk Timeout Disabled The hard disk does not shut down 10 15 30 45 Seconds or 1 2 4 6 8 10 15 Minutes after the last hard disk access The next time it is accessed the hard disk starts spinning again after a brief delay Resume On Time If this function is enabled the programming device is automatically switched on at the preset time Off means this function is disabled SIMATIC Field PG Manual A5E00075760 04 5 17 Configuring the SIMATIC Field PG Time for automatic restart Resume On Modem Enabled wakes the system up when an Ring incoming call is detected on your modem After Power Failure Stay Off After power failure the device is not switched on automatically Last State Provided it was switched on prior to a power failure the device is switched on again Power On Restores the previous power state before loss occured SIMATIC Field PG Manual 5 18 A5E00075760 04 Configuring the SIMATIC Field PG 5 6 The Boot Menu This menu allows you to set the priority of boot devices Advanced Security Power Version Item Specific Help Hard Drive CD ROM Drive Keys used to view or Network Boot configure devices lt Enter gt expands or collapses devices with a Or lt Ct
16. key to cancel this function NUM Key With these keys F NUM the emulated numeric block is switched from the alphanumeric keyboard to numeric keys The LED display lights up Press this key again to return to cursor control Scroll Lock Taste Monitor scrolling is either enabled or disabled with this key Tab Key This moves the cursor depending on the selected tabulator positions Fn Special Key combination key In conjunction with a second key key combination you activate other key codes for special applications with this key This key is also used to emulate the numeric keypad Figure 2 3 Numeric Keypad CTRL Key combination key This key is only used in combination with other keys For example you press CTRL ALT Delete to reset and restart the operating system For other uses of this key please refer to the user manual of the relevant user program SIMATIC Field PG Manual 9 10 A5E00075760 04 Getting Familiarized with the SIMATIC Field PG Function ALT Key combination key This key is only used in combination with other keys For example you can enter the hexadecimal value of an ASCII character using this key and the numeric keypad for example F ALT 132 corresponds to a ALT cr Key combination key You can use this key together with the other combination keys to generate other key codes For example you can generate the character on the German keyboard by typ
17. modems and other hardware modules can be connected to a RS 232 interface RTC Real Time Clock S SCSI Interface Small Computer System Interface Interface for connecting SCSI devices hard disk drives CD ROM drives Serial Interface Data is transmitted one bit at a time via a serial interface port serial interfaces are therefore slower than parallel interfaces Serial Port Adaptors D9 D25 This adapter is used to convert the COM1 V24 PLC interface of the SIMATIC PC family to a common socket SIMATIC Field PG Manual A5E00075760 04 Glossary 13 Glossary SETUP A program in which information about the device configuration that is the configuration of the hardware on the programming device is defined The device configuration of the programming device is preset with defaults Changes must therefore be entered in the SETUP if a memory extension new modules or a new drive are added to the hardware configuration SIMATIC S5 Memory Submodules Memory submodules for SIMATIC S5 which are programmed with the PG and can be plugged into an S5 programmable logic controller SIMATIC Memory Cards Memory submodules in credit card format for SIMATIC S5 and SIMATIC S7 which are programmed with the PG and can be plugged into an S5 or S7 programmable logic controller Software The collective term for all programs which are used on a computer The operating system and the user programs are part of the concept software
18. C is used for the data transfer Recovery Ensure that there is an available disk space of approximately 300 MB left on drive C after the selected recovery data have been copied SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 8 Confirm the end massage box 9 Start the Windows setup program LW I386 Winnt exe LW is the drive where the recovery data have been copied You can find the information on installation of Windows NT on the Recovery CD in the folder SUPPORT BOOKS Note If you want to become an expert user of Microsoft Windows NT Workstation see the Windows NT Workstation Resource Kit Version 4 0 is not included in the package It contains specific information for administrators who are responsible for installing managing and integrating Windows NT Workstation in a network or multiuser environment SIMATIC Field PG Manual A5E00075760 04 8 13 Reinstallation of the Software 8 7 Installing the SIMATIC Software You received the Backup PG CD with the product package that comes with your PG The Backup CD contains the data base for the STEP 5 ST Basics package not included in all delivered versions STEP 7 and STEP 7 Micro WIN and for the PG s electronic manuals To reinstall these program packages insert the CD Backup PG in the CD ROM drive Run Setup by clicking the SIMATIC Setup icon or by clicking Setup exe in the SIMATIC Software directory
19. COM1 V 24 MODEM AG 2 4 Memory Card 2 7 Micro Memory Card 2 7 MPI DP 3 20 PC Card 2 6 RJ45 Ethernet 3 22 USB VGA Interface Pinout 7 3 K Keyboard 2 3 2 9 Index 1 Index Keyboard LEDs 2 2 R Rechargeable battery 2 8 Restart RJ45 Ethernet Interface 3 22 LEDs 2 2 LS120 Disk Drive 2 18 S M S5 Memory Submodules Schnittstellen MPI DP 2 4 Memory expansion 2 8 4 2 Setting up Micro Memory Cards 3 17 SETUP Mouse buttons SIMATIC memory cards 3 16 MPI DP Interface 3 20 SIMATIC S7 Programmable Controller 3 20 SIMATIC Software 3 10 Special keys 2 10 P Status of the batons Be Stereo Loudspeaker Panel 3 11 Superdisk 2 18 Patch Cords 7 10 PC interface 3 18 Pin assignment Switching on system startup System LEDs COM1 7 8 DC In Ethernet T headphone 7 7 cata La Teach in C yee Battery 3 6 MPI DP 7 5 Touched d USB Type of disk drive built in 5 6 VGA 7 4 Point to point connection 3 19 Power supply 2 21 Processor Upgrade 4 4 U ki PROFIBUS 3 22 ae USB Interface SIMATIC Field PG Manual Index 2 A5E00075760 04
20. DIN IEC 60068 2 3 60068 2 30 60068 2 14 operation 5 to 80 at 25 C no condensation permitted storage transport 5 to 95 at 25 C no condensation permitted Mechanical specifications Vibration tested to DIN IEC 60068 2 6 operation 10 to 58Hz amplitude 0 035 mm 58 to 500Hz acceleration 5 m s2 transport 5 to 9Hz amplitude 3 5 mm 9 to 500Hz acceleration 9 8 m s2 Shock tested to DIN IEC 60068 2 29 operation half sine 50 m s2 30 ms 100 shocks storage half sine 250 m s2 6 ms 1 000 shocks Intel Mobile Pentiumlll Celeron see BIOS Level 2 cache first level 16 Kbytes data 16 Kbytes program laa second level 128 256 Kbytes processor dependent Main memory 64 Mbytes expandable to max 512 Mbytes 64 bit SO DIMM for memory expansion see BIOS Drives Standard Floppy disk drive 1 44 Mbytes Super disk LS120 or Super disk LS240 drive see BIOS Hard disk drive 2 5 capacity see BIOS IDE ATA 33 Optical Drive CD ROM 24x or DVD ROM 24x CD ROM 8x DVD or DVD ROM CD RW 24x CD ROM 8x DVD 8x CD RW equipment see BIOS Controller integrated in Intel Chipset FW82 815 EM Graphics memory Dynamic Video Memory Technology Resolutions frequencies colors CRT up to 1280x1024 85 Hz 4 mio colors or 1600 x 1200 75 Hz 265k colors Burning operation with DVD ROM CD RW permissible only in undisturbed enviromment SIMATIC Field PG Manual A5E00075760 04 B 3 Technical Specifi
21. Manual A5E00075760 04 1 4 Cleaning Important Notes Cleaning and Transporting the Field PG To prolong the lifetime of your Field PG and use it free of trouble do not expose it without cause to dust nor use aggressive cleaning agents to clean it e You can clean the display and the keyboard with customary screen cleaning tissues e The other case parts can be cleaned with a common household detergent Caution Never spray cleaning liquids directly onto the device and prevent ingress of liquid Transportation Despite of the rugged structure of the Field PG its installed components are sensitive against severe vibration and impact You can contribute to trouble free operation by taking a few precautions for the transportation e Ensure that the computer does not access anymore drives before you prepare it for transportation e Remove all floppy disks or CD ROMs from the respective drive e Switch off the PG refer to Chapter 2 5 e Disconnect all external devices from your PG e Close the display and the interface covers on the rear side of the device e Use the handle and for short transports e Pack the Field PG and all accessories into the supplied rucksack case if you are going to transport it over greater distances You should use the original package for the shipment of the programming device SIMATIC Field PG Manual A5E00075760 04 1 5 SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with th
22. SOM Safecard On Motherboard Consists of a monitoring module on the motherboard the driver and the SOM program Provides functions for monitoring various temperatures and the program cycle Watchdog Standby Power saving status for example hard disk drive or display turned off STEP 5 This is a software package which represents the basis for all other STEP 5 software packages With the programming device PG this package is used to program programmable logic controllers of the SIMATIC S5 family The language used is known as STEP 5 STEP 7 Programming software for the creation of user programs for SIMATIC S7 control STN Display Super Twist Nematic passive display SIMATIC Field PG Manual Glossary 14 A5E00075760 04 Glossary Suspend to Disk Transition to power off status with prior saving of the system contents to the hard disk drive Suspend to RAM Transition to power saving status with prior saving of the system contents to the TRAM T Text Cursor The cursor shows where text may be entered for example in text editors and in dialog windows In many applications the position of the cursor can be changed by moving and clicking with the mouse pointer TFT Thin Film Transistor Technology for liquid crystal displays LCD The display consists of a large grid of LCD cells Each one of the pixels represents a single cell The electrical field in the cells is supported by thin film transistors Touchpad The Touc
23. be changed or deleted by pressing Return and thus deactivated Disabled No password required for system boot Enabled Supervisor or user password must be entered for system boot Normal All types of hard disk access are permitted protected No operating system can be installed This is a way of protecting against boot viruses This mode of protection is not active unless Password on boot is set to enabled Supervisor Diskette access is not possible unless the Supervisor password was entered during system boot User Diskette access is not possible unless the user password was entered during system boot SIMATIC Field PG Manual A5E00075760 04 Configuring the SIMATIC Field PG 5 5 The Power Menu This menu has the following structure Advanced Security Version Item Specific Help Enabled Disabled Switch on off Power Savings to conserves Resume Time 00 00 00 To turn off power management choose Resume On Modem Ring Off te nea not functioning IESO Hard Disk Timeout Disabled After Power Failure Stay Off Fig 5 12 Power Menu The Power menu offers a number of power saver modes for environmentally friendly computing Power Savings Disabled No power saving functions Customize Maximum Power Savings Maximum Performance User selectable and preset power saving functions for maximum and minimum power saving You can set the parameters for Standby Suspend
24. ber that these are not fully supported by the Windows Me and Windows 2000 op erating systems nor by LS120 LS240 diskette drives If you use the P Tools we recommend that you use MS DOS Windows 3 x or Windows 95 and standard 1 44 MB floppies STEP 7 e Click on the icon SIMATIC Manager on the Windows desktop or e or click on Start and select the desired program by choosing Simatic gt STEP 7 Note The transfer of a STEP 7 configuration from on PG to another is supported by the STEP 7 file archiving functions Open the SIMATIC Manager select the menu command File gt Archive or File gt Retrieve You can find details on this proce dure in the STEP 7 online help section Steps to take for Archiving Retrieving STEP 7 Micro WIN 32 e Click on the On the STEP7 MicroWIN icon on the Windows Desktop or e Click Start on the Windows task bar and select the desired program with Simatic gt STEP 7 MicroWIN 32 SIMATIC Field PG Manual A5E00075760 04 Configuring And Operating The SIMATIC Field PG 3 5 Panel Field PG Panel Field PG helps you to work better with the Field PG It has the following functions Automatic execution of battery calibration Setting the display brightness Temperature display Hardware properties of the PC Card MPI and Ethernet interface Display of firmware versions The Panel is installed on devices with Windows Me and Windows 2000 Start the program via Start g
25. correct e Hit the F2 key check the configuration data in the SETUP program if necessary adapt the default values check the error messages in the first SE TUP menu Message on the Display No boot device available NTLDR not found check boot data carrier e No bootable disk in drive A e Replace the disk with a boot disk e Wrong hard disk type entered in SETUP e Use the Autodetect Fixed Disk function Message on the Display Keyboard stuck key failure e A key became blocked during the self test of e Check the keyboard Restart the system if need be the keyboard Every time a key is pressed a beep is heard and no characters are displayed e Keyboard buffer overflow e lt CTRL gt lt PAUSE gt lt gt key does not exist e Wrong keyboard driver e German keyboard lt ALTGr gt lt B gt e International keyboard lt gt key After power on error message Battery needs calibration cycle e Battery is no longer calibrated e Confirm error message with the F1 key e Runa teach in cycle SIMATIC Field PG Manual A5E00075760 04 6 1 SIMATIC Field PG Manual A5E00075760 04 Hardware Information F Chapter Overview section eseipon age SIMATIC Field PG Manual A5E00075760 04 1 1 Hardware Information 7 1 1 2 System Resources All system resources hardware address memory configuration IRQ DMA channel are assigned dynamically by the Windows OS depending on the hardware con
26. device only to be carried out by qualified personnel Qualified persons are defined as persons who are authorized to commission to ground and to tag circuits equipment and systems in accordance with established safety practices and standards Correct Usage Note the following Warning This device and its components may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens This product can only function correctly and safely if it is transported stored set up and installed correctly and operated and maintained as recommended Trademarks SIMATIC SIMATIC HMI and SIMATIC NET are registered trademarks of SIEMENS AG Third parties using for their own purposes any other names in this document which refer to trademarks Copyright Siemens AG 2002 All rights reserved Disclaim of Liability The reproduction transmission or use of this document or its We have checked the contents of this manual for agreement contents is not permitted without express written authority with the hardware and software described Since deviations Offenders will be liable for damages All rights including rights cannot be precluded entirely we cannot guarantee full created by patent grant or registration of a utility model or agreement However the data in this manual are reviewed design a
27. g AD Qa Slot for S5 Adapters for SIMATIC S5 memory modules and SIMATIC Memory Cards Fig 3 7 S5 Module Programming Interface Notice The S5 adapter and STEP 5 software is not included in all delivered versions Proceed as follows when working with S5 memory modules 1 Switch on your device 2 In your STEP 5 software start the function Administration gt Edit EPROM 3 With the type label on the top insert the SIMATIC S5 Memory Card or the S5 adapter into the Memory Card interface and then the S5 memory module 4 You can read program or erase EEPROMs only your S5 memory module with the EPROM functions of the STEP 5 software 5 Extract the S5 memory module 6 Close the EPROM functions of your STEP 5 software Caution You might damage the module if you insert or extract it while editing is in progress You must not remove the S5 memory module as long as the module programming status display is lit Always discharge your body s static electricity by briefly touching a grounded part of the device before you insert an S5 Memory Card SIMATIC Field PG Manual A5E00075760 04 3 15 Configuring And Operating The SIMATIC Field PG 3 8 Working with SIMATIC Memory Cards Working with SIMATIC Memory Cards SIMATIC memory cards can be read programmed and erased SIMATIC memory cards are available for SIMATIC S5 and SIMATIC S7 software
28. interference Bus connector 6ES7972 0BB10 0XA0 or 6ES7972 0BB20 0XA0 6ES7901 OBFO0 0AAO 5 m length Fig 3 12 Connection Using the MPI DP Interface Proceed as follows when connecting to a SIMATIC S7 programmable logic controller 1 Switch off your device 2 Open the interface cover on the left hand side panel of the device 3 Connect the cable to the MPI DP interface Caution Before plugging in the cables the static charge on your body the unit and the cables must be equalized You can do this by briefly touching the metal mounting plate for the interfaces on the rear panel Electrical isolation in the safety extra low voltage circuit SELV circuit SIMATIC Field PG Manual 3 20 A5E00075760 04 Configuring And Operating The SIMATIC Field PG Connecting Via the MPI DP interface you can connect your programming devices to e MPI networks S7 200 S7 300 and S7 400 or e PROFIBUS DP networks DP components MPI PROFIBUS DP Network Up to 32 devices PC PG or AS can be connected to the MPI DP interface to form a network segment The physical connection to the MPI PROFIBUS DP network is via a floating RS485 interface which is a component of the PG basic module Several MPI PROFIBUS DP network segments can be connect
29. jack can be used to connect microphones Pin assignment Micground 3 5 mm microphone plug Fig 3 5 Pin assignment of the microphone plug For microphone recordings select Programs gt Accessories gt Multimedia gt Audio Recorder in the Windows Start menu Connecting a Headphone You can connect headphones or active speakers with 3 5 mm stereo phono plugs to this jack Loudness is controlled via taskbar button or Programs gt Accessories gt Multimedia gt Loudness in the Windows Start menu The internal speakers are switched off when a headphone is connected Right GND 3 5 mm headphone stereo phono plug Fig 3 6 Headphone stereo phono plug SIMATIC Field PG Manual 3 14 A5E00075760 04 3 7 Configuring And Operating The SIMATIC Field PG Working with SIMATIC S5 Memory Submodules Editing SIMATIC S5 Memory Submodules aX You can read and program SIMATIC S5 memory submodules EPROMs or EEPROMs via the Memory Card interface Use the S5 adapter for S5 memory submodules that is included in the scope of delivery for devices with Step 5 software The S5 adapter consists of a Memory Card plug with an interface for the connection of S5 memory modules Refer to the STEP 5 manual for information on operating the programming software N ly X j GS Ga Ga A 0 Ga Gee Ga Con WZ
30. only be operated with the correct external power sup ply and or battery enclosed with the device The external power supply must not be covered up risk of overheating Notice The power plug must be disconnected to isolate the unit completely from mains A CSA or UL listed cord set must be used for operation in Canada and the USA For the United States and Canada In the United States and Canada the cord must be UL listed and CSA Labeled The male plug is a NEMA 5 15 style For operation with 120 V Use a UL listed CSA Labeled Cord Set consisting of a min 18 AWG Type SVT or SJT three conductor flexible cord max 4 5 m 15 feet in length and a parallel blade grounding type attachment plug rated 15 A min 125 V For operation with 240 V within the USA Use a UL listed CSA Labeled Cord Set consisting of a min 18 AWG Type SVT or SJT three conductor flexible cord max 4 5 m 15 feet in length and a tandem blade grounding type attachment plug rated 15 A 250 V For operation with 230 V outside of USA Use acord set consisting of a min 18 AWG cord and grounding type attachment plug rated 15 A 250 V The cord set should have the appropriate safety approvals and marks for the country in which the equipment will be installed The unit is intended for operation with grounded power supply networks TN networks VDE 0100 part 300 or IEC 364 3 Operation with non grounded or impedance grounded networks IT networks is
31. partitions The hard disk partitions will be erased The hard disk is partitioned on delivery as follows only for versions delivered with Windows one partition with the FAT32 file system with at least 6100 Mbytes one partition with the NTFS file system To restore the partition to its delivery state proceed as follows Primary Partition FAT32 File System 8 4 1 Boot from the Recovery CD and press ESC when the BIOS message Press lt F2 gt to enter Setup appears After initialization select the boot options in the boot menu 2 Select ATAPI CD ROM Drive 3 Select 2 Boot for FDISK FORMAT or Windows 98 Setup in the Microsoft Windows Startup Menu screen form 4 Start the Microsoft Windows hard disk configuration program with A gt FDisk In the screen form select Do you wish to enable large disk support Y N Y for Yes to support data media with large memory capacity 5 Create a primary DOS partition with 4090 MB Enter N for No for the question Do you want to use the maximum memory size available for the primary DOS partition and do you want to activate this partition and set the partition size to 6100 MB SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 6 To format the partition from the Recovery CD as described above in steps 1 to 3 reboot and then format drive C with the Format program Enter A gt Format C A i
32. spreading fire SIMATIC Field PG Manual A5E00075760 04 3 3 Configuring And Operating The SIMATIC Field PG 3 2 Connecting to the Power Supply Connecting to the Power Supply 3 4 The SIMATIC Field PG can be operated with the supplied external AC adapter on 120 V 230 V power systems or with the battery The external power supply automatically selects the voltage You should install the supplied battery pack before you connect the device to the power supply 1 Turn the Field PG over and place it down on the table while the display unit is closed Unlock and open the battery pack cover on the bottom of the device Insert the battery pack Close the cover and turn the device over again O fF W N Plug the supplied patch cord into the external power supply and plug the low voltage plug into the unit s connector 6 Connect the external power supply to a socket outlet with grounded protective conductor Te O r4 E Ce Connector for an external power supply Vu 17 5 V DC Fig 3 2 Power supply connection Warning The SIMATIC Field PG must only be operated with the provided power supply unit and or battery pack The external power supply must not b
33. swit ched off after the power supply has been disconnected By doing this you can be sure that the device is not switched on during transport and that the battery is not unintentionally discharged Energy Options 2 16 You can optimize the energy consumption of your PG using the energy options while maintaining the PG in operate state In Standby mode the screen and the hard disk drive are switched off to relieve the battery pack After you switch the PG back to normal mode the desktop is restored with your last configuration Since PG memory information is not written to the hard disk drive you should save your job before you switch the PG to standby mode Information stored in memory is lost in case of a power failure Note Select this mode if you briefly interrupt your work few hours In Hybernate mode the screen and hard disk drive are switched off All data in memory is stored to the hard disk drive before the PG is switched off When you switch on your PG again all programs and documents that were opened at the time of shut down are restored to the desktop Hybernate mode relieves the battery pack even more than Standby mode However it requires a longer time to reactivate the PG from this hybernating state Note Select this setting if you want to interrupt your work over an extended period se veral hours or over night Briefly push the On Off button to reactivate the PG from Standby or hybernate mode In standby mod
34. 000 0 8 9 8 5 1 Installing Drivers under Windows 2000 00 cee eee eee 8 11 8 6 Installing the Operating System Windows NT 000 eee 8 12 8 7 Installing the SIMATIC Software 0 00 c ccc eee eens 8 14 SIMATIC Field PG Manual x A5E00075760 04 Contents A Guidelines for Handling Electrostatically Sensitive Devices ESD A 1 WASE OD eane ea E E EE EE EAR A 2 Electrostatic Charging of PerSOns 0 0 c cece eee ees A 3 General Protective Measures Against Electrostatic Discharge Damage B Technical Specifications cece eee A 2 GOSSA arer a a A a cadecewerneeeheeede wn Glossary 1 SIMATIC Field PG Manual A5E00075760 04 xi SIMATIC Field PG Manual A5E00075760 04 Important Notes 1 1 1 Safety Instructions Caution The safety instructions given on the backside of the title page of this manual must be observed Before adding to the Field PG s functionality by expanding the hardware configuration see Chapter 4 observe the relevant safety instructions Notes on Inserting and Removing Modules Modules containing electrostatically sensitive devices ESDs can be identified by the following label Please observe and carefully follow the guidelines mentioned below when handling modules equipped with electrostatically sensitive devices e Always discharge your body s static electricity before handling modules equipped with ESDs for exa
35. 00075760 04 5 21 Configuring the SIMATIC Field PG 5 8 The Exit Menu The setup program is always terminated using this menu Advanced Security Power Boot Version Item Specific Help Exit Without Saving Changes Get Default Values Exit System Setup and Load Previous Values save your change to Save Changes CMOS Fig 5 16 The Exit Menu Save Changes amp Exit All changes are saved a system restart is carried out with the new parameters Discard Changes amp Exit All changes are rejected a system restart is carried out with the previous parameters Get Default Values All parameters are set to safe values Load Previous Values The last saved values are reloaded Save Changes Save all Setup settings SIMATIC Field PG Manual 5 22 A5E00075760 04 Error Diagnostics What Does This Chapter Contain This chapter will help you to locate identify and in some cases eliminate simple errors and faults Error Fault Remedy Device LED does not light up e PG is switched off e Press the Power Button e Power supply not properly connected e Check the power supply power cable and power plug e Battery run down or not installed e Charge or install the battery External monitor remains dark e LCD enabled is entered in SETUP e Enter CRT enabled or SIMULTANEOUS in SETUP Message on the Display Invalid configuration information Press the F1 key for continue F2 to run Setup utility e Configuration data not
36. 5E00075760 04 3 1 Configuring And Operating The SIMATIC Field PG 3 1 Unpacking and Setting Up the SIMATIC Field PG Unpacking Your SIMATIC Field PG Unpack your SIMATIC Field PG as follows 1 Remove the packing 2 Do not throw the original packing away Keep it if you need to transport the device at a later time Checking the Contents 3 Check the packing list to make sure that no components are missing 4 Check the packing and its contents for any transport damages 5 Please inform your local dealer of any shipping damages and discrepancies between contents and packing list Entering the Serial number F No and the Ethernet address 6 Enter the serial number and the Ethernet address of your programming device in the table below You can find the serial number on the type label attached to the base of the device The Ethernet address can be found in the BIOS setup settings in the main menu under the Hardware Options function If the device has to be repaired or has been stolen it can easily be identified by these numbers Entering the Microsoft Windows Product Key from the Certificate of Authenticity 7 Enter the Microsoft Windows Product Key from the Certificate of Authenticity COA in the table You will find the Product Key on the device You need the Windows Product Key if you want to reinstall the operating system Order No Microsoft Windows Product Key Ethernet Address SIMATI
37. ATIC Field PG Onboard Ethernet Enable the on board Ethernet interface Resources are managed by the BIOS PCI Plug amp Play mechanism Disabled Ethernet inactive Ethernet interface hardware is switched off The operating system can not operate the interface Enabled Ethernet active Subsequent plugging of the network cable and its operation possible at any time Hot Plug If no cable is plugged on system start the device checks during the boot sequence for a time of approx 30 seconds and when recovering from suspend mode for a time of approx 40 seconds for an existing Ethernet connection Noticeable delays do not occur as long as an active network connection does not exist LAN Remote Boot Enabled Disabled Switch on off Oprom scan to activate remote boot via the onboard Ethernet CRT LCD selection LCD only All data is output only to the internal LCD the 15 way VGA port is disabled CRT only For maximum resolution the display signals are output only to the 15 way VGA port the LCD interface of the VGA controller is disabled Simultan Auto Choose Simultan Auto if sometimes a CRT is connected CRT will only be active if connected Simultan Forced CRT Both display interfaces are enabled and operate simultaneously Note however that the LCD does not support all resolutions LCD Screensize Normal The display window in Text and Graphic modes is not expanded to full screen size Expand The Graphic
38. C Field PG Manual 3 2 A5E00075760 04 Configuring And Operating The SIMATIC Field PG Setting up your SIMATIC Field PG ZN Find a comfortable and safe working position for your SIMATIC Field PG 1 Put the SIMATIC Field PG down on its base on an even surface ata comfortable working height and distance 2 Ensure there is an easily accessible mains outlet near your place of work 3 Make sufficient desk space available to connect peripheral devices 4 Open the display by pulling the slide locks at the side of the display unit towards the front 5 Fold up the display and adjust it to a comfortable angle of inclination The display angle is adjustable from 0 180 Display lock Fig 3 1 Opening the Display Caution Always put the Field PG down on its base If you put it down on its interface side you risk that it will fall over and damage sensitive internal components Moisture ingress can damage the PG If you transport the device in cold weather and if it is exposed to extreme tempera ture fluctuation you have to acclimatize it to room temperature before you start to operate it Do not switch on the device until inside condensation has dried off completely This is the case for example with a temperature rise from 20 C to 20 C and after a waiting period of approx 12 hours Warning The computer casing is made of magnesium Contact with an external open fire source bears the risk of fire
39. II cards can realize devices such as modems fax and network interface cards Type III cards are equipped with devices that require more space for example wireless communication modules or rotary storage media hard disk drives for example Peripheral Component Interconnect high speed I O expansion bus Personal Computer Memory Card International Association Association of about 450 computer companies with the aim of setting worldwide standards for miniaturizing PC expansion cards and making their use more flexible offering the market a basis for development Cooperates with JEIDA See Cardbus interface Compact programming device especially for industrial applications The PG is fully equipped for programming SIMATIC PLCs SIMATIC Field PG Manual A5E00075760 04 Glossary 1 1 Glossary PG LINK Serial interface on a CPU CP IP module and coordination module PG MUX Used to connect a programming device Some CPUs are optionally equipped with two PG links Pixel Pix Element picture point The pixel represents the smallest element that can be reproduced on screen or on a printer PLC SIMATIC S5 programmable logic controller Plug and Play Generally a reference to the ability of a computer to automatically configure the system for communication with peripheral devices for example monitors modems or printers The user can plug in a peripheral and play it at once without manually configuring the system The Plug an
40. Labeling System Alphanumeric Keyboard The largest block of keys on the keyboard is the alphanumeric keyboard with all the keys for the letters of the alphabet numerals and special characters The characters are arranged in basically the same way as on a normal typewriter However there are a number of special keys which have special functions for the SIMATIC Field PG SIMATIC Field PG Manual A5E00075760 04 2 9 Getting Familiarized with the SIMATIC Field PG Special Keys The special keys in the alphanumeric keyboard have the following functions Function Backspace key This key moves the cursor one space to the left and deletes the character at this position Enter Key Return Enter Line Feed New Line The return or enter key is used mainly to terminate a command line in the operating system that is the command you have entered is executed when you press this key For other uses of this key please refer to the user ma nual of the relevant user program CAPS LOCK Key If you press this key the middle LED at the top right hand corner of your keyboard lights up All upper case characters and other characters are out put normally If you want to type lower case letters in this position you must first press the shift key If you are using an international keyboard you cancel this function by pres sing the CAPS LOCK key again The LED then goes out If you have a German keyboard you must press the shift
41. MPI DP socket C e C e Signal line B of MPI module input output 4 RTS AS RTSAS control signal for received data Input stream The signal is 1 active when the directly connected programmable controller is sending 5 M5EXT M5EXT return line GND of the 5 V power Output supply The current load caused by an external user connected between P5EXT and M5EXT must not exceed the maximum of 90 mA P5 EXT P5EXT power supply 5 V of the 5 V power Output supply The current load caused by an external user connected between P5EXT and M5EXT must not exceed the maximum of 90 mA a a Signal line A of the MPI module Input output RTS PG RTS output signal of the MPI module The control signal is 1 when the programming device is sending SIMATIC Field PG Manual A5E00075760 04 1 5 Hardware Information Ethernet 7 6 Pinout of the Ethernet interface LED yellow LED green 8 Fig 7 1 Ethernet port Pin No Designation Description Input Output 1 TD Transmitted data Output 2 TD Transmitted data Output 3 RD Received data Input 4 5 SYMR Internal 75 Q output 6 Received data Input 7 8 SYMT Internal 75 Q output S Shield LED yellow Connection LED green Activity is not necessary for data transfer SIMATIC Field PG Manual A5E00075760 04 Micro In Plug for external microphone Pinout 3 5 mm Microphone phono p
42. Me mory Card an S5 adapter or an MMC adapter is added SIMATIC Field PG Manual A5E00075760 04 3 17 Configuring And Operating The SIMATIC Field PG 3 10 PC Cards 3 18 Working with PC Cards The PC card interface supports two type II or one type III Cardbus card 32 bit or PCMCIA card 16 bit The SIMATIC Field PG has two PC card ports You can plug credit card format communication modules for MODEM FAX MODEM ISDN Token Ring ETHERNET memory expansion and SCSI interface modules into these ports PC card interface type I II Slot 1 lot PC card interface type I II III Slot 2 Ejector for PC Cards Fig 3 10 PC Card interface The PC Card ejectors have a ballpoint pen mechanism Before you insert the card ensure that the ejector is engaged To remove the PC Card push the ejector once to unlock it and a second time to eject the card Caution When you plug in the PC Card the Label must be on top Remove the card only after all data traffic has terminated risk of data loss and system failure You might damage the SIMATIC Field PG and the PC Card if you attempt to insert the card the wrong way round Always discharge your body s charge of static electricity by brief
43. PCP M files supplied with STEP 5 remember that these are not fully supported by the Windows Me and Windows 2000 operating systems nor by LS120 LS240 diskette drives If you use the P Tools we recommend that you use MS DOS Windows 3 x or Windows 95 and standard 1 44 Mbyte floppies Authorization with Authors W V2 x To authorize STEP 7 and other SIMATIC components you must use AuthorsW Start this program on the PG via the taskbar under Start gt Simatic gt AuthorsW Usage Notes for LS120 LS240 Superdisks The LS120 LS240 drive automatically recognizes the different floppy disk types Due to their higher storage capacity Superdisks are more sensitive to dirt temperature and shock than conventional disks Notice In order to achieve a reliable operation and high data security please note the following during use e Store and transport the Superdisk in the protective cassette included to keep dust and dirt from the disk e Remove Superdisk from the drive when it is not being read or written to keep dirt particles away from the disk Do not expose the disk unnecessarily to high operating temperatures Notice If possible avoid vibration of the device when using Superdisks Superdisks are more sensitive to vibration as a result of their high track density SIMATIC Field PG Manual 2 18 A5E00075760 04 2 6 2 2 6 3 Getting Familiarized with the SIMATIC Field PG Hard Disk Drive A variety of hard disk drives can be opera
44. RS485 galvanically isolated Memory address area OCCOOh 0CC7FFh or ODCOOh ODC7FFh IRQ 5 10 11 or 15 configurable per software 2 USB ports 1 x high current max 500mA 1x low current 100mA Ethernet RJ45 10 100 Mbits Intel controller Kinnereth DA82562ET C voltage input phono jack SIMATIC Field PG Manual B 4 A5E00075760 04 Technical Specifications Headphone and microphone connector for 3 5 mm phone jack respectively Function displays Status LEDs SIMATIC Field PG Manual A5E00075760 04 Caps Lock Scroll Lock Num Lock Battery status Device status Access to FD HD CR ROM S5 Module Memory Card active MPI DP token passing B 5 SIMATIC Field PG Manual A5E00075760 04 Glossary What does This Chapter Contain This chapter contains a glossary in which you will find a list of the terminology used in conjunction with the Siemens range of programming devices and a brief explanation of each of the terms SIMATIC Field PG Manual A5E00075760 04 Glossary 1 Glossary AC Alternating Current Current that changes its direction at regular intervals Access Protection Access to the programs and data of a programming device can be protected by passwords ACPI Advanced Configuration and Power Interface APM Advanced Power Management Application An application is a program which builds directly on for example the MS DOS Windows operating system Applications on your programming device a
45. SIEMENS Preface Contents Important Notes IMATI S C Getting Familiarized with the Pi SIMATIC Field PG Configuring And Operating The Field PG SIMATIC Field PG 3 SIMATIC Field PG Expansions Configuring the SIMATIC Field Manual Error Diagnostics Hardware Information Reinstallation of the Software ESD Guidelines O g gt z tg rp wo D O N O oao DA Technical Specifications Glossary Index Edition 01 2002 A5E00075760 04 Safety Guidelines This manual contains notices intended to ensure personal safety as well as to protect the products and connected equipment against damage These notices are highlighted by the symbols shown below and graded according to severity by the following texts Danger indicates that death severe personal injury or substantial property damage will result if proper precautions are not taken gt Warning gt indicates that death severe personal injury or substantial property damage can result if proper precautions are not taken Caution indicates that minor personal injury can result if proper precautions are not taken gt Caution indicates that property damage can result if proper precautions are not taken Notice draws your attention to particularly important information on the product handling the product or to a particular part of the documentation Qualified Personnel Repair maintenance and servicing of
46. Windows Protocols are configured in the Windows system control Notice A Class 5 Ethernet cable is required for operation with 100 Mbaud SIMATIC Field PG Manual 3 22 A5E00075760 04 SIMATIC Field PG Expansions 4 What Does This Chapter Contain This chapter shows you how to expand your SIMATIC Field PG with additional expansion memory submodules to increase its performance Please note the included comments on safety Chapter Overview Sen estore Installing Memory Expansion Submodules Replacing Backup Battery A SIMATIC Field PG Manual A5E00075760 04 4 1 SIMATIC Field PG Expansions 4 1 Installing Memory Expansion Submodules Standard Memory The motherboard has 2 slots for 144 pin SO DIMM memory submodules This allows you to expand the memory capacity of your SIMATIC Field PG toa maximum of 512 Mbytes moo Memory Submodules e Fig 4 1 Positions of the SO DIMM Memory Submodules You can install submodules of different capacity Only one module must be installed Refer to the catalog for the ordering data for suitable modules Memory o Modules _ 64 Mbytes 128 Mbytes 256 Mbytes SIMATIC Field PG Manual 4 2 A5E00075760 04 SIMATIC Field PG Expansions Caution T
47. You can select objects process menus or trigger functions with this Touchpad Operation You can use the Touchpad the very same way as a mouse the mouse pointer on the screen follows the movement of your finger on the pad You can click on icons or text with both mouse buttons First move the mouse pointer onto the icon Then select the icon with a left click As an alternative in a fully graphical user interface for example the Windows GUI you can mark an icon and then move the mouse pointer on top of it You can then open the icon with a double tap on the Touchpad You do not have to apply any pressure on the pad with your finger The sensor does not react to finger pressure but rather to the brief capacitance change on the touch point SIMATIC Field PG Manual A5E00075760 04 2 13 Getting Familiarized with the SIMATIC Field PG 2 4 LED displays Keyboard LEDs LED displays for the Num Lock Shift Lock and Scroll Lock keys They indicate the current status of the shift keys Meaning of the keyboard LEDs green Num Lockon off Num Lock off aa Shift Lock on Shift Lock off green Scroll Lock on off Scroll Lock off System LEDs The system LEDs battery device drives MPI DP and Memory Card indicate the status of the battery pack the unit the drives as well as the MPI DP and Memory Card interfaces These LEDs are also visible when the display is closed Meaning of the System LEDs 2 14 green Battery
48. afety instructions in this section Configuration Modifications made to the system hardware may make it necessary for you to adapt the original hardware configuration This is described in Chapter 5 Error fauit diagnostics Chapter 6 explains how to deal with simple faults and problems that you can diagnose and in some cases eliminate yourself Reference data Chapter 7 contains information about hardware addresses interrupt assignments and connecting cables Reinstalling the i i i If it does happen that you need to reinstall the software you can find the procedures in Chapter 8 ESD guidelines The guidelines on the handling of electrostatic sensitive devices are particularly important for service and maintenance technicians who are installing expansion units or carrying out error analysis with the SIMATIC Field PG SIMATIC Field PG Manual A5E00075760 04 Preface Glossary The glossary defines and explains important terms Alphabetical index The alphabetical index will help you to find passages in the text relating to important terms and keywords quickly and reliably Conventions The abbreviation PG oder device is also used within this manual for the product designation SIMATIC Field PG Further Support If you have questions related to the use of the products which are not answered in this manual please consult your Siemens representative in your local agency You will also find your representatives for rep
49. airs and spare parts at http www ad siemens de partner Trainingscenter Siemens offers a number of training courses to familiarize you with the SIMATIC S7 automation system Please contact your regional training center or our central training center in D 90327 Nuremberg Germany for details Telephone 49 911 895 3200 http www sitrain com SIMATIC Documentation on the Internet You will find the documentation on the internet at http www ad siemens de support Use the Knowledge Manager to find the documentation you need quickly If you have any questions or suggestions concerning the documentation you can use the Documentation conference in the internet forum SIMATIC Field PG Manual A5E00075760 04 V Preface Automation an Drives Service amp Support Available worldwide around the clock Worldwide Nuremberg Technical Support Free Contact Local time Mo Fr 7 00 to 17 00 Phone 49 180 5050 222 Fax 49 180 5050 223 E mail techsupport ad siemens de GMT 1 00 Europe Africa Nuremberg Authorization Local time Mo Fr 7 00 to 17 00 Phone 49 911 895 7200 Fax 49 911 895 7201 E mail authorization nbgm siemens de GMT 1 00 Sy x KST Nuremberg SIMATIC Basic Hotline Worldwide Nuremberg Technical Support charged only with SIMATIC Card Local time Mo Fr 0 00 to 24 00 Phone 49 911 895 7777 Fax 49 911
50. and Text modes are expanded to full screen size Touchpad Enabled The Touchpad is switched on Disabled The Touchpad is switched off Auto Detect The Touchpad is automatically detected Note All modifications of this interface are not active until a restart of the PG Enabling disabling the soundchips of the basic module SIMATIC Field PG Manual A5E00075760 04 5 13 Configuring the SIMATIC Field PG 5 3 The Advanced Menu Menu Structure Advanced Security Power Boot Version Item Specific Hel EA Reset Configuration Data No Select the operating IRQ Resource Exclusion system installed on your system which you will use most Serial port A Auto commonly Floppy disk controller Disabled Note An incorrect Large Disk Access Mode DOS setting can cause some operating Local Bus IDE adapter Primary amp Secondary systems to display unexpected behavior Legacy USB Support Disabled Fig 5 9 Advanced Menu Settings in the Advanced Menu Installed O S Plug amp play means that all modules are automatically detected and installed providing they support the Plug amp Play functionality other BIOS handles the entire Plug amp Play capability default configuration WinME The operating system handles part of the Plug amp Play functions WinME 2000 The operating system handles a part of the Plug amp Play functions Reset Configuration All installations under Plug amp Play ar
51. ary Master 10056MB E l i xample a Primary Slave None Secondary Master ATAPI Removable Hour Minute Second Secondary Slave CD ROM Month Day Year Selectable submenu Memory Cache Write Back Boot Options Keyboard Features Hardware Options System Memory 640 KB Help Window Extended Memory 128511 KB p Operating keys Fig 5 1 Main SETUP Menu sample Menu Structure The screen is divided into four sections In the top section you can select the menu screens Main Advanced Security Power Boot Sequence Version Exit In the left of the center section you can select various settings or submenus Brief help texts appear on the right for the currently selected menu entry The bottom section contains information for operator inputs You can move between the menu screens using the cursor keys lt and Menu Meaning Main System functions are set here Advanced An extended system configuration can be set here Security Security functions are set here for example a password Power Power functions can be selected here Boot The boot priorities are defined here Version Information about the programming device s release status Exit Used for terminating and saving SIMATIC Field PG Manual 5 4 A5E00075760 04 5 2 The Main Menu Selectable submenu Advanced System Date Diskette A Primary Master Primary Slave Secondary Master Secondary Slave Memory Cache
52. board Features Submenu Switches Numlock on or off following power on Key Click A keystroke can be heard Keyboard auto repeat Increase of the automatic keyboard rate rate Keyboard auto repeat On delay of automatic keyboard repeat delay SIMATIC Field PG Manual A5E00075760 04 5 11 Configuring the SIMATIC Field PG Hardware Options Field The following submenu appears when you select the Hardware Options field in the main menu Hardware Options Item Specific Help REEN Enable or disable the eee PCI Multi Point Programming interface Enabled Interface MPI DP Cardbus PCMCIA Slot Enabled Also this item Enables Disables the SIMATIC programming interface Onboard Ethernet Enabled Ethernet Address 08000624E1CB LAN Remote Boot Disabled CRT LCD selection Simultan Auto LCD Screensize Expand Touch Pad Auto Detect Fig 5 8 Hardware Options Submenu The parameters of the interfaces present on the basic module are set here Entry Meaning PCI MPI DP Enables the CP5611 compatible MPI DP interface Programming interface Displays enable or disable status of the SIMATIC Memory Card Interface Enable follows the enable of PCI MPI DP Cardbus PCMCIA Disabled Enable Cardbus PCMCIA Slot interface deactivated Enabled Resources are managed by BIOS PCI Plug amp Play mechanisms SIMATIC Field PG Manual 5 12 A5E00075760 04 Configuring the SIM
53. cations LC D display Wee T_T OG Size 246 mm x 185 mm equivalent to 31 cm 14 1 in 1024 x 768 XGA Colors available max 256 k Vertical frequency 60 Hz Contrast 100 1 Brightness gt 70 cd m Response time 50 50 ms ton toff Permissible defective areas bright pixel max 7 dark pixel max 9 Sound controller Intel 8201BA BAM AC97 Compatibility Sound Blaster Pro and Microsoft Sound System meets PC98 PC99 and WHQL specifications Record and playback features Up to 16 bit stereo 48 KHz sampling rate full duplex 3D audio effects and ESFM TM music synthesizer Internal speaker Max power output 2 x 0 5 W Keyboard Standard notebook Key spacing 19 05 mm Key stroke Keytops international German Integrated pointing device Touchpad with 2 mouse buttons COM1 TTY V 24 or TTY 20 mA active or passive up to 100 m 25 pole socket no galvanic isolation Interface for external monitor 15 pole VGA socket Cardbus 2 interfaces for PC cards type I type II or type III Cardbus controller from Tl PCI 1420 Memory card Programming interface for SIMATIC memory cards and S5 memory modules Micro Memory Card Interface for Micro Memory Card MPI DP port 9 pole sub D socket Transfer rate 9 6 Kbaud to 12 Mbaud configurable per software Operating mode Galvanically isolated data line A B control line RTS AS RTS PG 5V supl voltage 90mA max Grounded shielding of the DP12 patch cord Physical interface
54. ccc eee eee teen enees 5 5 5 3 The Advanced Menu 0 00 ccc cee ee eee eee teenies 5 14 5 4 The Security Menu 1 een eee n ene a 5 16 5 5 The Power Menu 0 00 cee eee eee eee ee eens 5 17 5 6 The Boot Menu co ste se secteste stra hh casino cnt oe te bese arth ovata He eine ah oh eae eh to ob dc th 5 19 5 7 The Version Menu 0 00 ccc eee eee tenet e ee nnes 5 21 5 8 he EXIL IVT 2 ser se carne na ri ba che near e a Ea E A E G 5 22 Error Diagnostics 0cecececeeeceeeecececueueeeeevetueueunennananes Hardware Information 0 ccc eee ees 7 1 7 1 System Resources 6 cece een teen eee nes 7 2 7 2 interface PINOUT ces ibs tetoerack ace ered siii ek Ree ee Ee cheek eee eR 7 3 7 3 if 618 C70 0 ae eee ee a iar i ee eer 7 10 8 Reinstallation of the Software 0c cece ees 8 1 Cause Remedy 22 lt lt cedsch2ie ee4u0dbseedbbiaeeedeedicscdsdind 8 2 8 2 Restoring the Hard Disk Data Deleted 0 0 00 eee 8 2 1 Creating Partitions under Windows Me 00ce cence eae 8 2 2 Creating Partitions under Windows 2000 00 cee e eee 8 2 3 Creating Partitions under Windows NT 0 0 0c eee ence eee 8 3 Installing the Operating System Windows Me 00000 ee 8 3 1 Installing Drivers under Windows Me 0000 cence eens 8 4 Installing Drivers and Software 0000s cece eee eens 8 8 8 5 Installing the Operating System Windows 2
55. ce to the power supply unit and the unit to mains to charge the battery As soon as the device is connected to mains via the power supply unit the battery is recharged Replacing the Battery ZN You can replace a run down or defective battery with a new replacement battery 1 Turn the Field PG over and place it with closed display unit onto a flat mat 2 Unlock and open the battery cover on the bottom of the casing 3 Replace the battery 4 Close the cover and turn the device over again Warning Do not use a battery type other than that supplied The battery is available as spare part Refer to the catalog for ordering data SIMATIC Field PG Manual A5E00075760 04 3 5 Configuring And Operating The SIMATIC Field PG Disposal of Used Batteries Lithium lon batteries can be recycled Their components can be used as raw materials for new batteries or other products Effective recycling of batteries is only possible when the used batteries are collected according to type Notice Observe the local regulations for disposal of recycling materials Charge Status Indicator The battery has electronic circuitry for showing the current charge status The electronics incorporate a metering unit which has to be calibrated at regular intervals so that it can compensate for error The chemical properties of the battery change in the course of time so the electronics have to relearn the battery s characteristics at regular intervals
56. d Play PC requires both a BIOS that supports Plug and Play and a corresponding expansion card PROFIBUS Bus system based on the PROFIBUS standard Components of the SIMATIC S5 and S7 series programming devices programmable logic controllers programmable control systems distributed I Os can be networked using PROFIBUS Programmable Logic Controller System The programmable logic controllers PLC of the SIMATIC S5 system consist of one or more CPUs and various I O modules The PLCs of the SIMATIC S7 system for example S7 200 S7 300 S7 400 consist of one or more CPUs and various I O modules Programmable Controller AS This programmable controller PLC consists of the central unit a CPU and of diverse I O modules Pull Down Menu See Drop Down Menu SIMATIC Field PG Manual Glossary 12 A5E00075760 04 Glossary R RAM RAM Random Access Memory is a volatile read write memory in which every memory location can be addressed individually and its contents changed RAM is used to store data and programs Restart Warm start of a computer in operate state without switching off the power supply Ctrl Alt Del ROM ROM Read Only Memory is a non volatile memory in which every memory location can be addressed individually They contain factory set programs and data that are not lost in the event of a power failure RS 232 Interface The RS 2382 interface is a standardized interface for data transmission Printers
57. e ccsssnccacesdareatensuceadeseoseucemrese semuonmaseweeswese nue es 1 important NOES 6 sas ose sessenesucscenceass eau REE Aa a ueaeeaense 1 1 1 1 Safety Instructions 0 cc eee ee eee e eens 1 1 1 2 Certificates Directives and Declarations 0 000 cee eee ees 1 2 1 3 Certification for the USA Canada and Australia 05 1 3 1 4 Cleaning and Transporting the Field PG 0 c cece 1 5 2 Getting Familiarized with the SIMATIC Field PG 0000000008 2 1 2 1 Components of the SIMATIC Field PG 0 0c cece eee 2 2 2 2 FRO YVOOAIG eaer dh esa Weed on Ea a e a a wea ern eee ead ee eee 2 9 2 3 T D aia boa ees eae ore crete ater wee estes od wa etd E woes E l 2 13 2 4 LED GISOlay sreo cake ato eenet E E ea bone need ye cence aber ean 2 14 2 5 On Off Pushbutton Power Button 0 0 2 15 2 6 VSS satina Bem new ech ah cab acs Ae ww he ee eh ww at eee ae 2 6 1 Floppy Disk Drive 2 6 2 Hard DISK DIVO gesrrssyas eee eed Bre AERE ee aera ESR 2 6 3 Optical DAV Cac scccte science cine toaw ed a neh w be eewdae ebaned ee bbs atone ole es 2 7 External Power Unit and Battery 0 cc cee eee 2 21 3 Configuring And Operating The SIMATIC Field PG 2 000 3 1 3 1 Unpacking and Setting Up the SIMATIC Field PG 3 2 3 2 Connecting to the Power Supply 0 c cece cee eee eee 3 4 3 3 Battery Operation 0 0 ccc teen etn eens 3 5
58. e SIMATIC Pa Field PG What do you find in this Chapter This chapter briefly presents the most important components of the SIMATIC Field PG Get familiarized with these elements before you start to commission the PG Chapter Overview Section Description e Components of the SIMATIC Field PG 2 3 Touchpad SIMATIC Field PG Manual A5E00075760 04 2 1 Getting Familiarized with the SIMATIC Field PG 2 1 Components of the SIMATIC Field PG View with closed display 2 2 SNEINS 1 System LEDs The system LEDs battery status L device Lon drives a MPI DP_ MPI DP and Memory Card CI indicate the status of the battery unit drives MPI DP and Memory Card interface These LEDs are also visible when the display is closed The drive access displays are arranged on the right hand side of the corresponding drives For detailed information on these LED displays refer to Chapter 2 4 of the electronic manual 2 Keyboard LEDs The keyboard LEDs display the current status of the shift keys Num Lock fa Caps Lock al and Scroll Lock When the unit is booting the displays of these keys flicker briefly The keyboard is ready for operation 3 Device Handle Folding handle for transporting the device Caution Always stand the PG on its base If you place it down on the interface side
59. e covered up risk of over heating For reasons of safety you must use the patch cord and power supply that is inclu ded in the delivery Operation of the unit is only permitted on grounded 120V 230V power supply networks SIMATIC Field PG Manual A5E00075760 04 3 3 Configuring And Operating The SIMATIC Field PG Battery Operation Battery Operation If not connected to an external power supply unit the SIMATIC Field PG can be operated with the internal battery pack 1 Switch on the device Make sure the battery is sufficiently charged before you start work 2 Work as usual with your SIMATIC Field PG 3 In battery mode the red signal of the battery LED indicates that the battery is in low condition Stop your work and save your data There are only a few minutes of battery operation remaining Notice Do not start a work session in battery mode unless the battery is fully charged This is the only way of ensuring that the full on battery operating time is available and that you will be warned in good time when battery power is low When connected to the external power supply unit the orange battery LED indicates that the battery is being charged When connected to the external power supply unit the green battery LED indicates that the battery is fully charged and that charging has stopped The battery might be partially or totally discharged when you start commissioning fro example running down Connect the devi
60. e deleted and Data reconfiguration is triggered the next time the system boots The entry is then reset to No System components that do not support Plug amp Play have to be entered manually The Plug amp Play system components are initialized after the next system start Serial port A Configure Serial Port A with the options Disabled No configuaration Enabled User configuration Auto BIOS or OS chooses confuguration SIMATIC Field PG Manual 5 14 A5E00075760 04 Configuring the SIMATIC Field PG Floppy disk controller Enabling or disabling the floppy controller of the basic module Large Disk Access OTHER The tables are not adapted Mode DOS Drive letters are constructed according to Enhanced IDE compatible DOS drive access Local Bus IDE adapter Disabled No local IDE adapter Primary One IDE adapter for max two drives Secondary Primary amp Secondary Two IDE adapters for max four drives Legacy USB Support Disabled Disables the support for Legacy USB Enabled Enables support for Legacy USB The resources used by an interface are released when you disable the interface in question Submenu IRQ Resource Exclusion The I O addresses and interrupts are default settings and recommended respectively mms IRQ Resource Exclusion Item Specific Help DAZE E Available Reserves the specified Available IRQ for use by legacy Available ISA devices Available Available
61. e installed in the programming device to increase the width of the memory F File A complete named collection of information such as a program a set of data used by a program or a user created document A file is the basic unit of storage that enables a computer to distinguish one set of information from another Formatting Formatting divides the memory area on a magnetic data medium into tracks and sectors Formatting deletes all the data on a data medium Every data medium must be formatted before it is used for the first time Function Keys Function keys can be divided into two different types the normal function keys which are assigned a particular function of the computer for example delete key and programmable function keys softkeys SIMATIC Field PG Manual Glossary 6 A5E00075760 04 Glossary H Hard Copy The output of the complete contents of the screen on a printer is called a hard copy Hard Disk Drive Hard disk drives Winchester drives are a form of magnetic disk memory where the magnetic disks are permanently built into the drive HMI Human Machine Interface Industrial Ethernet Bus system based on the Ethernet standard Components of the SIMATIC S5 and S7 series programming devices programmable logic controllers programmable control systems can be networked using Industrial Ethernet NICs Interface module Module for the connection of peripheral hardware Interrupt When the proces
62. e standard OS for PCs Link between programming devices and programmable controllers by means of interface modules physical cables and the corresponding software to allow data exchange between the devices Operating System Glossary 10 Collective term for all functions which in conjunction with the hardware control and monitor execution of the user programs the distribution of resources among the individual user programs and the maintenance of the operating mode for example Windows 98 MS DOS SIMATIC Field PG Manual A5E00075760 04 P Glossary Parallel Interface Password PC PC Card PCI PCMCIA PG Information is transmitted byte for byte via a parallel interface port This means that the transmission rate is very fast The programming devices have one parallel interface LPT1 Unique sequence of characters that is entered for user identification See Access Protection Personal computer Trademark of the Personal Computer Memory Card International Association PCMCIA Designation for auxiliary cards that conform with PCMCIA specifications The PC Card that has roughly the size of a credit card can be plugged into a PCMCIA slot Version 1 specifies cards of Type I with a thickness of 3 3 millimeters which is conceived mainly for use as external memory Version 2 of the PCMCIA specification also defines a card Type II with thickness of 5 mm and a card of the Type IIl with a thickness of 10 5 mm Type
63. e the system LED flashes in hybernate mode all displays are switched off SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with the SIMATIC Field PG 2 6 Drives 2 6 1 Floppy Disk Drive Depending on the device configuration a standard floppy disk drive 1 44 MB a Superdisk LS120 or a Superdisk LS240 drive is built in 3 5 diskettes of 1 44 MB and Superdisks up to 120 MB can be used with the LS120 drive For LS240 additional Superdisks up to 240 Mbyte are required Types of Diskette You can use the following diskettes Standard LS120 LS240 Floppy Disk Drive 3 5 inch Jv Jv Jv 1 44 Mbytes 135 TPI 3 5 inch Jv Jv 120 Mbytes 3 5 inch JV 240 Mbytes Handling Diskettes Access to the floppy drive is displayed by the drive s status indicator and on the status indicator for external devices at the front of the keyboard Caution Risk of data loss Do not remove diskette until the access indicator on the drive has been switched off Emergency Removal bei LS120 LS240 Disk Drive When the device is switched off the disk can be forced out by using a pin for example a bent paper clip SIMATIC Field PG Manual A5E00075760 04 2 17 Getting Familiarized with the SIMATIC Field PG Information on the LS120 LS240 Disk Drive Restrictions P Tools under STEP 5 Data cannot be edited in PCP M format on the LS120 LS240 drive using P Tools under STEP 5 Notice When you use the P Tools for editing
64. ed via repeaters The complete MPI PROFIBUS DP network can comprise up to 127 stations Data transmission rates from 9 6 Kbps to 12 Mbps are possible in the PROFIBUS DP MPI network SIMATIC Field PG Manual A5E00075760 04 3 21 Configuring And Operating The SIMATIC Field PG 3 13 Networking the Field PG with Other Stations on PROFIBUS Networking the SIMATIC Field PG on PROFIBUS PROFIBUS is an open and robust bus system for industrial use It can be used to configure networks with up to 32 stations per segment PROFIBUS DP supports data transfer rates from 9 6 Kbaud to 12 Mbaud How the Network Functions The network operates on the Master Slave Principle with Token Passing complying with DIN19245 PROFIBUS It distinguishes between active and passive stations An active station receives the token and passes it on to the next station within a specified time Hardware Requirements Using the following components for example you can connect or network the SIMATIC Field PG with PROFIBUS e RS 485 MPI DP interface adapter integrated e Shielded twisted pair bus cable or connecting cable to network 3 14 Ethernet RJ45 Ethernet Interface Networking Field PG via RJ45 Ethernet Interface The RJ45 Ethernet interface is a Twisted Pair TP Interface for data transfer rates of 10 100 Mbaud This on board interface is compatible with Intel pro 100 PCI Adapters The Plug amp Play interface is automatically recognized in
65. een tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Shielded Cables Shielded cables must be used with this equipment to maintain compliance with FCC regulations Modifications Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment Conditions of Operations This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Canadian Notice This Class B digital apparatus complies with Canadian ICES 003 Avis Canadien Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada This product meets the requirements of the AS NZS 3548 Standard SIMATIC Field PG
66. enance work Hold modules without touching the pins of components or printed conductors In this way the discharged energy cannot affect the sensitive devices If you have to carry out measurements on a module you must discharge your body s electrostatic charge before you start the measurement by touching grounded metallic parts Use grounded measuring devices only SIMATIC Field PG Manual A 4 A5E00075760 04 Technical Specifications Note At the start of the PG the BIOS messages Summary Screen offer a precise over view of your SIMATIC Field PG configuration SIMATIC Field PG Manual A5E00075760 04 B 1 Technical Specifications Dimensions w x h x d 328 x 294 x 52 mm Weight approx 4 kg Line voltage external power supply 100 VAC to 240 VAC 10 15 Line voltage frequency 50 60 Hz 47 to 63 Hz Brief voltage interruption acc to Namur gt 20 ms at 93 V AC power supply max 10 times per hour min recovery time 1 s Max power consumption 90 W Output DC voltage external power supply 16 V Output DC current external power supply max 4 5A Output DC power external power supply max 72 W Standby power battery operation approx 4 8 Ah 10 8V with thermostatic switch and multi fuse recyclable chargeable up to 40 C 108 F high num ber of charge cycles under severe conditions low self di scharge rate Degree of protection IP30 covers closed Quality assurance ISO 9001 Safety Re
67. erating system can be installed using the Windows Me setup program The Windows Me setup can be started by entering HD gt WIN9x SETUP EXE HD drive on which the WINME folder was transferred to Windows Me Installation Sequence If a Windows operating system is already installed or if the programming device has been started with a bootdisk data transfer is executed using the program OEMSETUP EXE To do this start the program OEMSETUP EXE on the recovery CD and continue the sequence as of point 5 If there is no operating system installed then please do the following 1 Insert the Recovery CD in the CD ROM drive and switch on the PLC 2 To boot from the Recovery CD proceed as follows When the message Press lt F2 gt to enter Setup appears on the screen press the ESC key After initialization a boot menu to select the boot options is displayed 3 Select ATAPI CD ROM Drive 4 When the Microsoft Windows 98 Startup Menu is displayed select 1 Boot for CD Recovery 5 You have to confirm the SIEMENS End User License Agreement with the F8 function key Pressing ESC allows you to decline the agreement and cancels the installation 6 In the next screens you can select the components which are to be copied from the CD to the hard disk Transfer of at least the folder WIN9x is necessary for the Windows Me installation or setup 7 A selection of disk drives for the data transfer is next offered T
68. figuration drivers and connected peripheral devices You can view the current configuration of system resources or possible conflicts with the following operating systems Windows Me Start gt Programs gt Accessories gt System Tools gt System Information Windows 2000 Start gt Settings gt Control Panel gt Administrative Tools gt Computer Management gt System Information SIMATIC Field PG Manual A5E00075760 04 Hardware Information 7 2 Interface Pinout DC In Jack for connecting the AC DC adapter Potentials 17 5 VDC b OV Ground USB Both interfaces are conceived for high current USB 500mA However they cannot be used simultaneously as high current interface Data Data line Input Output ee SIMATIC Field PG Manual A5E00075760 04 1 3 Hardware Information VGA 15 pole socket for an external monitor Pinout N 9090 e w Sx l O l S 0000 e Finno Designation Descripion inpuvoupu a a e E e e e T oo p e m Unassigned C e e e fm Grong 7 f feo e Ca e Unassigned C e O o EXT_H Horizontal synchronizing Output pulse 14 EXT_V Vertical synchronizing pulse Output DDC_CLK Display Data Channel Clock Input Output SIMATIC Field PG Manual 7 4 A5E00075760 04 MPI DP Hardware Information Pinout of the
69. from Siemens AG Bereich Automation and Drives A amp D AS RD4 Postfach 1963 D 92209 Amberg Tel 09621 80 3283 Fax 09621 80 3278 Observing the Setup Guidelines The setup guidelines and notes on safety given in the manual must be observed on startup and during operation SIMATIC Field PG Manual 1 2 A5E00075760 04 Important Notes Connecting peripheral devices Noise immunity when connected to industrial standard peripheral devices conforms with the requirements of EN 500082 2 ISO 9001 Certificate The quality assurance system for the whole product process development production and marketing fulfills the requirements of ISO 9001 corresponds to EN29001 1987 This has been certified by the German society for the certification of quality management systems DQS EQ Net certificate no 1323 01 Software License Agreement The PG is shipped with the software already installed Please observe the relevant license agreements 1 3 Certification for the USA Canada and Australia Security One of the following markings on a device is indicative of the corresponding approval UL Underwriters Laboratories UL to the UL 1950 standard GF Canadian Standard Association CSA to Standard C22 2 No 950 SIMATIC Field PG Manual A5E00075760 04 1 3 Important Notes EMC USA Canada Australia 1 4 Federal Communications Commission Radio Frequency Interference Statement This equipment has b
70. gt o SZ gt gt Z C _ 198mm gt al 21 V 330 Ohm NV lt 19H _ _ ______ am 6 19 eo 4 lt lt C 9 7 gt f C 10 V Housing 1 om 8 Shielding C 1 Housing 20 Fig 7 4 SIMATIC S5 Standard Cord Set MPI DP Cord Set for SIMATIC S7 You can use the 6ES7901 0BF00 0AAO cord set to connect your SIMATIC Field PG to a SIMATIC S7 PLC Please not the comments in Chapter 3 SIMATIC Field PG Manual 7 10 A5E00075760 04 Reinstallation of the Software What Does This Chapter Contain This chapter explains how to resinstall the software if the pre installed software contains errors Chapter Overview Sesion OOOO oeenn ae 81 Cause Cause Remedy pasi the Hard Disk Data Deleted aoa oT DA the da a System Windows Me o a7 ea insaing Overs andSotware B ee ee insane Opraing Syston Windows NT ee SIMATIC Field PG Manual A5E00075760 04 8 1 Reinstallation of the Software 8 1 Cause Remedy In case of software errors reinstall your software using the Recovery CD and the Backup PG CD To restore all directories and files that were copied to your hard disk at the first set up proceed as follows 1 If itis possible to save your authorization proceed as described below 2 If it is not possible to save y
71. he disk drive selected is not the installation drive for Windows It is the drive on which the necessary installation files and extensions are saved You need approximately 250 MB of additional memory for the Windows setup following the transfer During a standard installation Windows Me is installed on drive C Therefore please make sure when selecting a drive that there is enough available memory on drive C after the data transfer SIMATIC Field PG Manual A5E00075760 04 8 Reinstallation of the Software 8 3 1 Procedure 8 4 8 8 8 You can start the Windows Me setup after the data transfer and after having confirmed the completion prompt via the program HD WIN9x SETUP EXE HD drive on which the folder WIN9x was transferred to Installing Drivers under Windows Me In order to add or change the device driver of any hardware component proceed as follows e Open the dialog box System Properties Click Start point to Settings click Control Panel then double click System e Click the Device Manager tab click on the plus sign next to the hardware type and then double click on the selected hardware component e Click the Driver tab and then click Update Driver then follow the instructions that appear on your screen e The Driver tab may not be available for some devices In this case try to change the driver by double clicking on the desired hardware icon in the
72. he electronic components of the printed circuit boards are highly sensitive to electrostatic discharge Certain precautionary measures are therefore necessary when handling such components These measures are explained in the guidelines for handling electrostatically sensitive devices in Appendix A Installing memory submodules To plug in expansion submodules proceed as follows 1 Switch off the device Caution Do not install a memory module while the PG is switched on You might damage the PG as well as the memory module Disconnect all cables on the device Close the display unit Place the Field PG onto a soft mat with the display unit facing down a e Ph Remove the four retaining screws of the cover above the memory expansion slot Remove the cover o 7 Plug the module into the slot Note the recess reversal protection on the plug side of the SO DIMM module 8 Push the module down by applying light pressure until it locks into place 9 Replace the cover and secure it with the four screws Caution Make sure that the modules are seated securely in the slots otherwise they can drop out and be damaged The memory configuration is detected automatically When you switch on the unit the distribution of System and Extended Memory is displayed on screen SIMATIC Field PG Manual A5E00075760 04 4 3 SIMATIC Field PG Expansions 4 2 Processor Upgrade You can boost the performance of your SIMATIC F
73. hpad is used in many programs with mouse control as an input device for cursor control and menu operation The Touchpad works with touch sensitive sensors The cursor can be moved over the screen with the touch of a finger U USB Acronym for universal serial bus A serial bus with a data transfer rate of 12 megabits per second Mbps for connecting peripherals to a microcomputer USB can connect up to 127 peripherals such as external CD ROM drives printers modems mice and keyboards to the system through a single general purpose port This is accomplished by daisy chaining peripherals together USB is designed to support the ability to automatically add and configure new devices and the ability to add such devices without having to shut down and restart the system hot plugging User Interface The software controlled menus and screens on the monitor through which the user communicates with the program SIMATIC Field PG Manual A5E00075760 04 Glossary 15 Glossary User program Contains all instructions declarations and signal processing data that can be used for system or a process control It is assigned to a programmable module for example CPU FM and can be split into smaller blocks modules V VGA Video Graphics Array Industrial standard graphics adapter for use with any commonly used software W Warm Start Restart of a computer in operate state without switching off the power supply Ctrl Alt Del Wo
74. ield PG with a processor upgrade Consult your local dealer or service partner Notice If an upgrade is implemented for example to a processor with a different fre quency it may be important to also upgrade the BIOS You must only install components approved by Siemens 4 3 Replacing Backup Battery The Field PG has a backup battery which powers the hardware clock after the device has been switched off Warning Danger of explosion when replacing the battery improperly Only replace with the same type The backup battery can be ordered from Siemens as a spare part order number A5E00047601 Old lithium batteries should be given back to the manufacturer recycled or dispo sed of as hazardous waste If you have any questions please consult your local dealer or service partner SIMATIC Field PG Manual 4 4 A5E00075760 04 Configuring the SIMATIC Field PG What Does This Chapter Contain In this chapter you will learn how to configure your programming device You need to do this if you change your system by adding removing or exchanging expansion modules and memory expansions or by replacing a system module Chapter Overview cen ston Te one the Device Configuration with SETUP The Advanced Menu se fesen se ening se meon E CY er meves o SIMATIC Field PG Manual A5E00075760 04 5 1 Configuring the SIMATIC Field PG 5 1 Changing the Device Configuration with SETUP Changing the Device Configurat
75. ing ALT B PRINT combination key Using the Print key you can output the current screen display to a printer depending on the software used PAUSE combination key The Pause key interrupts program execution in the majority of applications Cursor Keys The key block shown in the picture below is used for cursor control Home and End are operated in combination with the Fn key Page back Cursor up Move cursor to beginning of file Page forward Move cursor to end of file Cursor left l i Cursor right i Cursor down Fig 2 2 Cursor Keys SIMATIC Field PG Manual A5E00075760 04 9 11 Getting Familiarized with the SIMATIC Field PG Numeric Keypad with Fn Key By pressing F and one of these keys the numbers and characters can be used provided Num Lock is switched on Fig 2 3 Numeric Keypad Function Keys A row with twelve programmable Function Keys is located above the alphanumeric keyboard The individual function of these keys depends on the software you are working with SIMATIC Field PG Manual 2 12 A5E00075760 04 Getting Familiarized with the SIMATIC Field PG 2 3 Touchpad Definition The Touchpad is an input device for cursor control and menu operation with mouse operation in numerous programs You can move the cursor to any screen position by touch A left button click on sets the mark The right button assignment varies depending on the user program
76. ion Your PG configuration is set for working with the software supplied with the unit You should only change the preset values if you have modified your Field PG in any way or if a fault occurs when the unit is powered up SETUP Program The SETUP program is in the ROM BIOS Information about the system configuration is stored in the battery buffered RAM of the SIMATIC Field PG You can use SETUP to set the hardware configuration for example hard disk type and define the system characteristics You can also use SETUP to set the time of day and date Incorrect SETUP Data If incorrect SETUP data are detected when you boot the system the BIOS prompts you to e Start SETUP by pressing F2 or e Continue booting by pressing F1 Starting SETUP On completion of the startup test the BIOS gives you the opportunity of starting the SETUP program by displaying the following screen prompt PRESS lt F2 gt to enter SETUP To start SETUP proceed as follows 1 Reset your PG warm or cold restart 2 Press the F2 key as long as the BIOS prompt appears on the screen SETUP Menus The various menus and submenus are listed on the following pages You can get all the information you need for the SETUP entry selected from the Item Specific Help part of the relevant menu SIMATIC Field PG Manual 5 2 A5E00075760 04 Configuring the SIMATIC Field PG Screen Display Following Power On With the standard setting of your PG the
77. is charged orange Battery is being charged red Battery low only with battery operation off No battery installed green Line operation orange Battery operation green flashing Line operation system in Standby mode orange flashing Battery operation system in Standby mode Unit is switched off MPI DP MPI interface active green Module programming Memory Card or Micro Memory Card active Note Battery charging is terminated when the battery pack is fully charged or if for ex ample the upper temperature limit is exceeded during charging The current bat tery status can be queried in Windows Me Windows 2000 green Access to external storage media hard disk drive optical drive floppy disk drive SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with the SIMATIC Field PG 2 5 On Off Pushbutton Power Button Switching the Field PG On Hold the On Off button Power Button down for approx 1 second to switch on the device Switching the Field PG Off Either close the display lid actuate the On Off pushbutton Power Button or select the respective Windows Start menu command to toggle the Field PG from normal mode to one of the following modes e Standbymode Save to RAM e Hibernate Save to Disk e Off Windows is shut down If operated under a Windows OS the device is switched off automatically when you shut it down If not operated under Windows you can switch the device off via On Off pushbut
78. ischarged In most cases the damage caused by an overvoltage is not immediately noticeable and results in total damage only after a prolonged period of operation SIMATIC Field PG Manual A5E00075760 04 Guidelines for Handling Electrostatically Sensitive Devices ESD A 2 Electrostatic Charging of Persons Charging Every person with a non conductive connection to the electrical potential of its Surroundings can be charged electrostatically Figure A 1 shows you the maximum values for electrostatic voltages which can build up on a person coming into contact with the materials indicated in the figure These values are in conformity with the specifications of IEC 801 2 Voltage in kV O 1 Synthetics 2 Wool Antistatic material for example wood or concrete ooh OmoO nNWARH 8 T 6 5 4 3 2 1 5 Relative air humidity in Fig A 1 Electrostatic Voltages which can Build up on a Person SIMATIC Field PG Manual A5E00075760 04 A 3 Guidelines for Handling Electrostatically Sensitive Devices ESD A 3 General Protective Measures Against Electrostatic Discharge Damage Ensure Sufficient Grounding Make sure that the personnel working surfaces and packaging are sufficiently grounded when handling electrostatically sensitive devices You thus avoid electrostatic charging Avoid Direct Contact You should touch electrostatically sensitive devices only if it is unavoidable for example during maint
79. keyboard is the collection of keys which are used to input data text characters letters numbers special characters and control commands in a computer The keyboard forms the input interface between the user and the computer Liquid Crystal Display Display type on the base of liquid crystals with a thin film polarized molecular structure enclosed between two transparent electrodes Light Emitting Diode for example status display Semiconductor diode that transforms electrical energy into light The LPT1 port Centronics port is a parallel interface that can be used to connect a printer SIMATIC Field PG Manual A5E00075760 04 Glossary LS120 Drive Floppy disk drive that is capable of storing 120 MB of data on a single 3 5 inch floppy disk LS 120 drives are also compatible with other floppy disk formats Main Memory Main memory is a RAM memory in the CPU that is accessed by the CPU during user program processing Memory Card Memory Cards in credit card format memory for user programs and parameters for example for programmable modules and CPs Micro Memory Card New and very compact card for SIMATIC Memory Expansion See Extended Memory Modem Communications device that enables a computer to send and receive data over a telephone line Modulator and demodulator of a signal transmission facility It converts the digital pulses from a computer into analog signals and vice versa Module Modules are boa
80. lled using the Windows NT setup program Windows NT Installation Sequence lf a Windows operating system is already installed or if the PC has been started with a user created bootdisk the transfer of the data takes place using the program OEMSETUP EXE To do this start the program OEMSETUP EXE on the recovery CD and continue the sequence as of point 5 lf there is no operating system installed then please do the following 1 Insert the Recovery CD and reboot the system 2 To boot from the CD proceed as follows When the message Press lt F2 gt to enter Setup appears on the screen press the ESC key After intialization a boot menu to select the boot options is displayed 3 Select ATAPI CD ROM Drive 4 When Microsoft Windows 98 Startup Menu is displayed select 1 Boot for CD Recovery 5 You have to acknowledge the SIEMENS End User License Agreement with the F8 function key Pressing ESC allows you to decline the agreement and cancels the installation 6 In the next screens you can select the components which are to be copied from the CD to the hard disk Transfer of at least the folder I386 is necessary for the Windows NT installation or setup 7 Select the drive for data transfer You can use the selected drive as the installation drive for Windows For the Windows setup you need an available disk space of approximately 300 MB on the installation drive for Windows Caution By default drive
81. log Start gt Settings gt Control Panel gt Regional Options gt tab General box Menus and dialogs gt tab Input locales box Input language SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 8 5 1 Installing Drivers under Windows 2000 In order to add or change the device driver of any hardware component proceed as follows Procedure e Click Start point to Settings click Control Panel then double click System e Click the Device Manager tab click on the plus sign next to the hardware type and then double click on the selected hardware component e Click the Driver tab and then click Update Driver then follow the instructions that appear on your screen e The Driver tab may not be available for some devices In this case try to change the driver by double clicking on the desired hardware icon in Control panel SIMATIC Field PG Manual A5E00075760 04 8 11 Reinstallation of the Software 8 6 Installing the Operating System Windows NT Installation of the Recovery CD in Microsoft Windows NT This CD contains encoded data which can only be transferred onto a SIEMENS SIMATIC programming device Data transfer is carried out with the OEMSETUP EXE program on the CD ROM or after booting from the CD ROM with the Recovery function After transferring the required data to the hard disk the operating system can be insta
82. lug Hardware Information Fig 7 2 Microphone Headphone Plug for external headphones Pinout Right GND 3 5 mm Stereo phono plug Fig 7 3 Headphone SIMATIC Field PG Manual A5E00075760 04 1 1 Hardware Information COM1 V 24 TTY 7 8 Serial interface COM1 AG V 24 Modem Pinout 3 OHO OQOQDOQOOQOOQOGQOOOQOOO O QOGOQHOQOOOQOGOOOO O s oo N Ol f D1 Serial transmit data Output 2 5 ee fea Functional ground reference AG ewp O O O me foma isoatedcurertsowre O DTR S1 Data terminal ready a iwo fws pat z osson SIMATIC Field PG Manual A5E00075760 04 Hardware Information Gender Changer for COM1 Use the Gender Changer 25 pin 9 pin to convert your COM1 V24 PLC interface to a common 9 pole pin strip Just plug the Gender Changer into the COM1 socket and secure it with the two hex head screws The V24 and TTY interfaces for COM1 can be alternately used SIMATIC Field PG Manual A5E00075760 04 1 9 Hardware Information 7 3 Patch Cords SIMATIC S5 Patch Cord You can use the SIMATIC S5 cord set not included in all delivered versions to connect your SIMATIC Field PG to a SIMATIC S5 PLC Please not the comments in Chapter 3 PG side Patch cord PLC side 25 pole pin strip 6ES5 734 2BD20 15 pole pin strip active NN included in the consignment passiv 330 Ohm AN A a V of juas 99
83. ly touching a grounded part of the device e g the metal mount of the port before inserting or removing a card in accordance with the instructions for handling electrostatically sensitive components EGB guidelines Otherwise disruptions might occur Notice In order to use a PC card you must enter BIOS SETUP open the Main menu se lect the Hardware Option submenu and set Cardbus PCMCIA Slot to Enabled SIMATIC Field PG Manual A5E00075760 04 Configuring And Operating The SIMATIC Field PG 3 11 Connecting the Field PG to a SIMATIC S5 Network Point To Point Connection In this section you will learn how to connect your Field PG to a programming device or S5 PLC using a point to point connection You can establish a point to point connection by connecting the Field PG to another programming device using a TTY connection Notice The interface is connected to potential The SIMATIC STEP 5 programming software and the patch cord for the connec tion to the S5 PLC is not supplied with all versions Connecting the Field PG to the S5 PLC You can connect the Field PG to a SIMATIC S5 PLC via COM1 TTY interface port The patch cord for connecting to SIMATIC S5 CPUs is not included with all delivered versions Order no 6 S5734 2BD20
84. magnetic disk in a plastic cover to protect it from getting scratched Display Flat screen monitor of the PG Double Click Pressing and releasing the left mouse button very quickly twice in succession without moving the mouse This action is normally to open an object or program Drives Devices for operating rotary disk media diskettes hard disk CDs Drivers These are programs which are part of the operating system They adapt user program data to the specific formats required by I O devices such as hard disk printers and monitors Drop Down Menu In graphics supported programs a menu line is positioned on the top edge of the screen The menu titles contained in this line can be set either as drop down or pull down menus Drop down menus roll down as soon as the mouse pointer passes over a menu title Pull down menus only roll down when the menu title is clicked on Different functions can then be called from these menus by moving the mouse and clicking on an item in a menu SIMATIC Field PG Manual A5E00075760 04 Glossary 5 Glossary E EPROM EEPROM Submodules These are plug in submodules with EPROM EEPROM chips S5 user programs can be stored on them These programmed submodules are then plugged into specially designed slots in the programmable logic controller Ethernet Local network bus structure for text and data communication with a transfer rate of 10 Mbaud Extended Memory Memory extensions can b
85. minute and the entries remain unchanged You should always check that the interfaces for which you select Auto are in fact connected to drives Select User if you want to define the hard disk type yourself in which case remember that you also have to set the other fields including Cylinder Heads Sectors Track and WritePrecomp to the correct values for the type of hard disk in question Multi Sector Transfer Field The entry in the Multi Sector Transfer field defines the number of sectors transferred per interrupt The value depends on the drive and should be set only by setting the Type field to Auto Disabled Zp oy B76 sectors LBA Mode Control field If the LBA Mode Control field enabled disabled is set to Enabled the system supports hard disks with capacities greater than 528 Mbytes The value depends on the drive and should be set only by setting the Type field to Auto 32 Bit I O Field The setting in the 32 Bit I O field defines the mode of access for the drive Disabled To Bit access Enabled 32 Bit access default Transfer Mode Field The settings in these fields define the interface s data transfer rate The value depends on the drive and should be set only by setting the Type field to Auto Hit ESC to exit the submenu SIMATIC Field PG Manual A5E00075760 04 5 7 Configuring the SIMATIC Field PG Memory Cache Field 5 8 The following pop up menu appears when y
86. mple by touching a grounded object e Devices and tools must be free of static electricity e Always pull the power plug and disconnect the battery before connecting or disconnecting modules containing ESDs e Touch modules fitted with ESDs by their edges only e Never touch wiring posts or printed conductors on modules containg ESDs SIMATIC Field PG Manual A5E00075760 04 1 1 Important Notes 1 2 Certificates Directives and Declarations Notes on the CE Symbol The following applies to the SIMATIC product described in this operating instruction EMC Directive This product fulfils the requirements for the EC directive 89 336 EEC on electromagnetic compatibility and the following fields of application apply according to this CE symbol al Emitted Interference Noise Immunity Residential and commercial areas and EN 50081 1 1992 EN 50082 1 1992 small businesses Industry EN 50081 2 1993 EN 50082 2 1995 The product is also compliant with the Standards EN 61000 3 2 1995 Harmonic currents and EN 61000 3 3 1995 Voltage fluctuation and flicker Field of Application Requirement for Low Voltage Directive This product fulfils the requirements for the EC directive 73 23 EEC on low voltage and was tested to EN60950 Declaration of Conformity The EC declarations of conformity and the documentation relating to this are available to the authorities concerned according to the above EC directive
87. n 3 5 SIMATIC Field PG Manual A5E00075760 04 3 Configuring And Operating The SIMATIC Field PG 3 4 Commissioning Switching on the Field PG 3 4 1 The operating system and system software supplied with the SIMATIC Field PG are preinstalled on the hard disk Time consuming installation of the operating system and SIMATIC software programs is not required Just unpack and power up your unit and you can immediately start your programming tasks without having to take extensive setup actions e To power up the device hold down the On Off switch for on the top side of the keybord for at least one second When powering up the device you have to distinguish between the following Initial start to set up the Field PG s software and a Restart after cold start and authorization Cold Start of the SIMATIC Field PG When powering up the SIMATIC Field PG for the first time the operating system is set up automatically depending on the version delivered Windows Me Windows NT or Windows 2000 Professional Please proceed as follows 1 Switch on the Field PG 2 The PG executes a self test During self test the following message appears on the screen Press lt F2 gt to enter SETUP Wait until the message disappears and follow the instructions displayed on the screen 3 Enter your product key The product key can be found on the device in the line Product Key of the Certificate of Authenticity Caution
88. nd time options for example from hour to minute using the tabulator key Diskette A The type of disk drive built in to the PG is set here The following entries are possible Disabled If a floppy drive or an LS120 drive does not exist default 1 44 MB 3 1 2 Setting for an integrated floppy drive A for 3 1 2 inch 1 44 MB disks Primary Master Primary Slave Secondary Master Secondary Slave When you select such a menu field via Enter key the following submenu is opened Primary Master 10056 MB Item Specific Help Auto User you enter LBA Format parameters of hard disk Total Sectors 19640880 drive installed at this or connection Maximum Capacity 10056MB Auto autotypes hard disk drive Multi Sector Transfers 16 Sectors installed here LBA Mode Control Enabled 1 39 you select 32 Bit I O Enabled pre determined type of Transfer Mode hard disk drive installed here CD ROM a CD ROM drive is installed here ATAPI Removable removable disk drive is installed here Fig 5 3 Primary Master SIMATIC Field PG Manual 5 6 A5E00075760 04 Configuring the SIMATIC Field PG Type Field The parameters you can select here are usually stored on the IDE drive The Auto setting in the Type field means that these values are automatically read from the drive and written into memory If Type is selected for a drive that cannot be detected a timer times out in approximately 1
89. not permitted The cord set must meet safety requirements in the respective country SIMATIC Field PG Manual A5E00075760 04 2 21 Getting Familiarized with the SIMATIC Field PG Battery 2 22 The included battery pack is installed underneath a cover The Field PG has an integrated Lithium lon rechargeable battery This makes the device portable meaning you can use it without the external power supply The battery also prevents data loss as a result of power failure Once the external power supply unit is connected the battery is charged The following conditions are important e When the device is switched off charging takes approximately 3 hours fast charging e When the device is switched on charging takes approximately 3 to 6 hours depends on the system load e Charging stops as soon as the battery is fully charged e A fully charged battery that is put on shelf runs down within approximately 2 to 4 months depending on the temperature and whether it is installed It must then be recharged e You can check the battery status in Windows See also Section 3 3 Battery Mode e tis advisable to run a teach in cycle every now and again see Section 3 3 When the unit is connected to the power supply the green battery LED indicates that the battery is fully charged Battery charging is then stopped Notice When not used over an extended period weeks switch off the Field PG and re move the battery see Sec
90. oft Windows 98 hard disk configuration program with A gt FDisk A is the CD ROM drive Select the dialog box for enable large disk support for installing a FAT16 partition activate support Y N N for No Create a primary DOS Partition of 2045 MB for a FAT 16 file system Answer the question Do you wish to use the maximum available size for a 2045 MB FAT16 partition with Y for Yes In order to continue with the next step Create a Save to Disk Partition the primary partition needs to be formatted Use the Recovery CD to boot as described in steps 1 to 3 above and then format drive C with the program Format Type A gt Format C The creation of NTFS partitions is done under the hg NT setup program Starting the Windows NT setup is described in chapter SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 8 3 Installing the Operating System Windows Me You should only follow these steps when you wish to upgrade from Windows 2000 NT to Windows Me or if you reinstall Windows Me The operating system can be reinstalled or restored using the Recovery CD This CD contains encoded data which can only be transferred onto a SIEMENS SIMATIC programming device Data transfer is carried out with the OEMSETUP EXE program on the CD ROM or after booting from the CD ROM with the Recovery function After transferring the required data to the hard disk the op
91. ons and SCSI interfaces CardBus Cards are not supported by Windows NT 6 Air venting slots Here is the ventiduct Caution The ventiducts for incoming and outgoing air must not be obstructed Otherwise there is a risk of overheating SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with the SIMATIC Field PG View of the left side GS a T ca Ga AD r 1 Opening for the Kensington lock K Opening for the connection of a security cable You can protect your PG against theft by locking the cable to a writing desk or any other heavy appliance 2 Air venting slots Here is the ventiduct Caution N The ventiducts for incoming and outgoing air must not be obstructed Otherwise there is a risk of overheating 3 Memory Card interface _ Interface for reading programming or deleting SIMATIC Memory Cards for SIMATIC S5 and SIMATIC S7 You can also use the supplied S5 adapter to program or read SIMATIC S5 EPROM submodules 4 Micro Memory Card interface This interface can be used to read program or delete Micro Memory Cards SIMATIC Field PG Manual A5E00075760 04 2 Getting Familiarized with the SIMATIC Field PG Bottom view
92. or Caution Make sure the monitor can handle the resolution and refresh rate settings Other wise it can result in damage 7 USB Second USB port 8 DC in 17 5 V Socket for the DC output plug of the power supply that is included in your consignment SIMATIC Field PG Manual A5E00075760 04 2 5 Getting Familiarized with the SIMATIC Field PG View of the right side 2 6 1 Optical drive Depending on the device configuration it can come with a CD ROM a DVD ROM or a DVD ROM CD RW drive For example you can read the electronic manual of the supplied Backup PG CD with this drive 2 Floppy disk drive Depending on the device configuration a standard floppy disk drive 1 44 MB a Superdisk LS120 or a Superdisk LS240 drive is built in 3 5 diskettes of 1 44 MB and Superdisks up to 120 MB can be used with the LS120 drive For LS240 additional Superdisks up to 240 Mbyte are required 3 Headphones You can connect an external stereo headphone or another audio output device to this headphone jack The internal soeaker is automatically disabled when a headphone is connected 4 Microphone Va You can connect an external microphone or another audio output device to this microphone jack 5 PC Card slot The PC Card slot accepts Cardbus 32 Bit and PCMCIA 16 bit cards You can plug in credit card size communication modules for MODEM FAX MODEM ISDN Token Ring ETHERNET memory expansi
93. ou select the option Memory cache in the main menu Advanced Security Power Boot Version ltem Specific Help System Time 15 35 32 System Date 09 05 2000 Controls caching of Diskette A Disabled eons eae Primary Master 10056MB memory and memory Primary Slave above one megabyte Secondary Master Secondary Slave Mrrite Write Back Boot Options Keyboard Features Hardware Options System Memory 640 KB Extended Memory 128511 KB Fig 5 4 Memory Cache Menu A cache is a fast memory buffer between the CPU and main memory DRAM Recurrent memory access operations are executed in the fast cache instead of main memory if the function is enabled In rare instances involving some hardware and software combinations it may be necessary to disable the cache because the program runtimes or waits are too short on account of the fast cache Disabled Cache is disabled Write Through Write access is not concluded until the entry has been made in main memory Write Back Write access is concluded immediately the entry in main memory takes place in the background default SIMATIC Field PG Manual A5E00075760 04 Configuring the SIMATIC Field PG Option Boot Options The following submenu appears when you select the option Boot Options in the main menu Boot Options Item Specific Help LELEO Allows the system to skip certain tests while booting This will decrease the
94. our authorization please contact the customer support hotline see Getting Started They will provide you with the information necessary for your authorization Then proceed as described in Section 8 2 Saving Authorization on Diskettes 8 2 Please proceed as follows e Insert authorization disk in drive A e Click Start on the Windows task bar and e Select Start gt Simatic gt AuthorsW gt AuthorsW to open the authorization tool which will help you to save all authorizations on your authorization disk SIMATIC Field PG Manual A5E00075760 04 Reinstallation of the Software 8 2 Restoring the Hard Disk Data Deleted 8 2 1 Creating Partitions under Windows Me After installing a new hard disk it is necessary to create partitions with the program FDisk when the partitions have errors or need to be changed Caution By deleting or creating partitions or logical DOS hard drives all saved data is lost on the hard disk All drives on the hard disk will be erased The hard disk is delivered with the following installed only for versions delivered with Windows Me aFAT32 PRI DOS partition with 6100 MB aFAT32 EXT DOS partition To restore the partitions to their original condition please do the following Primary Partition 1 To boot from the Recovery CD hit the ESC key when the BIOS message Press lt F2 gt to enter Setup appears on screen After initialization a boot menu opens in which yo
95. ows The Windows NT versions do not support this power management 7 Display interlock The display unit is connected to the base unit with two locks The slide interlock is mounted at the side of the display unit 1 USB Universal Serial Bus connector You can use the USB port to connect external devices for example CD drives printers modems as well as a mouse and keyboard The Windows NT versions only support mouse and keyboard 2 COM1 V 24 MODEM O Cl jac The COM1 TTY interface is used to connect for example S5 programmable controllers PLC The supplied adapter Serial Port Adaptors D9 D25 can be used to convert the interface into a 9 pole standard V 24 interface for connecting serial interface devices for example modems mice or printers me 3 Ethernet g RJ45 Ethernet connector Ethernet is a local area network with a bus structure for data communication with a data transfer rate of 10 100 Mbit per second Mbps 4 MPI DP Multipoint Interface The MPI DP interface is isolated from line potential You can use it to connect the SIMATIC Field PG to an S7 automation system or to a PROFIBUS network SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with the SIMATIC Field PG 5 Air venting slots Here is the ventiduct Caution The ventiducts for incoming and outgoing air must not be obstructed Otherwise there is a risk of overheating 6 VGA Here you can connect an appropriate external monit
96. quirements VDE 0805 EN 60950 and IEC 60950 Protection class to IEC 60536 Protective separation between supply and secondary circuit via external power supply lt 45 dB A to DIN 45635 Electromagnetic compatibility EMC Emitted interference limit value class B to EN 55022 EN 6100 3 2 Line fed interference on AC supply lines 2 kV IEC 61000 4 4 burst 1 kV IEC 61000 4 5 us pulse line to line 2 kV IEC 61000 4 5 us pulse line to ground Noise immunity on signal lines 2 kV IEC 61000 4 4 burst length gt 3 m 2 kV IEC 61000 4 5 us pulse line to ground length gt 20 m Noise immunity to discharges of static Contact discharge IEC 61000 4 2 ESD electricity Air discharge IEC 61000 4 2 ESD Immunity to RF interference 10 V m with 80 amplitude modulation at 1 kHz 9 kHz 80 MHz to IEC 61000 4 6 10 V m with 80 amplitude modulation at 1 kHz 80 kHz 1GHz to IEC 61000 4 3 10 V m pulse modulated 50 duty cycle 9OOMHz and 1 89 GHz to IEC 61000 4 3 Magnetic field 30 A m 50Hz to IEC 61000 4 8 Lithium lon rechargeable battery 9 cells with charge status monitoring SIMATIC Field PG Manual B 2 A5E00075760 04 Technical Specifications Ambient conditions Temperature tested to DIN IEC 60068 2 1 DIN IEC 60068 2 2 operation 5 C to 40 C no condensation permitted storage transport 20 C to 60 C no condensation permitted 10 C h 20 C h Relative humidity tested to
97. r DC Direct Current Unidirectional electrical current DIMM Dual Inline Memory Module Memory RAM chips that are installed on the PCB similar to the more common SIMM Single Inline Memory Module chips The DIMM with its 64 bit data bus architecture has connections on both sides which are connected to different circuits for processing different instructions SIMMs however have a 32 bit data bus architecture where all lines are connected to the same circuit for processing the same instructions DIMMs can be installed in the computer as single chip SIMMs on the contrary only in pairs SIMATIC Field PG Manual Glossary 4 A5E00075760 04 Glossary Device Configuration The configuration of a programming device contains information on hardware and device options such as memory configuration drive types monitor network address etc The data are stored in a configuration file and enable the operating system to load the correct device drivers and configure the correct device parameters If changes are made to the hardware configuration the user can change entries in the configuration file using the SETUP program Disk Drive The disk drive floppy disk drive is used to store programs and data on diskette write access or to load from diskette to the computer read access Diskette The diskette floppy disk is an external data access memory on which all types of files and programs can be stored The storage medium is a round
98. rds printed circuit boards which can be plugged into a programmable logic controller or programming device They are available for instance as central controller modules interface modules or as bulk memory modules Monitor The device on which images generated by the computer s video adapter are displayed Mother Board The mother board is the core of the programming device From here data are processed and stored interfaces and device I Os are controlled and managed SIMATIC Field PG Manual A5E00075760 04 Glossary 9 Glossary Mouse The mouse is a pointing device with which the user inputs coordinates x y By moving the mouse the mouse pointer can be moved at will around the screen By pressing the left mouse button the position is marked The other mouse keys may have different assignments according to the application With the mouse objects can be selected menus processed and functions started Mouse Pointer MPI DP MS DOS N Network O The mouse pointer is moved across the worktop screen by means of the mouse The mouse pointer selects for example objects which are to be processed The multipoint interface MPI is the programming device interface for SIMATIC S7 It offers simultaneous operation from one central station of several programming devices text displays and operator panels The stations on the MPI can communicate with each other The single Microsoft Disk Operating System is one of th
99. re for example the STEP 5 Basic package STEP 7 etc ASCIl Editor With an ASCII editor you can edit text files which are stored in ASCII code B Backup Duplicate of a program storage medium or database Created to backup or to protect irreplaceable data of working copies as a precaution against corruption or destruction Some applications automatically create backup copies while managing both the current version as well as the previous version that is stored on the hard disk drive Base Memory The base memory is a part of the main memory It is 640 Kbytes for all programming devices The size is entered in the SETUP menu under the entry System Memory and is not changed even if the memory is extended SIMATIC Field PG Manual Glossary 2 A5E00075760 04 Glossary BIOS Acronym for Basic Input Output System On PC compatible computers the set of essential software routines that tests hardware at startup starts the operating system and supports the transfer of data among hardware devices Boot Diskette Boot disk that contains a boot sector and an initial loader for the operating system Boot Start or restart of the PG During the boot sequence the operating system is transferred from the system drive into the main memory Booting Loading operation which transfers the operating system to the main memory Bps The speed in bits per second with which information is transmitted over a data link C Cache The cache memor
100. re reserved regularly and any necessary corrections included in subsequent editions Suggestions for improvement are Siemens AG welcomed Bereich Automation and Drives l Geschaeftsgebiet Industrial Automation Systems Siemens AG 2002 i A rell Postfach 4848 D 90327 Nuernberg Technical data subject to change ae Cues U 7 Automation amp Drives Siemens Aktiengesellschaft A5E00075760 ormens Preface Purpose of the Manual This manual contains all the information you need for commissioning and using the SIMATIC Field PG programming device It is intended both for programming and testing debugging personnel who commission the device itself and connect it with other units automation systems further programming devices as well as for service and maintenance personnel who install expansions or carry out fault error analyses Where is this Manual Valid This manual is valid for all supplied variations of the SIMATIC Field PG and describes the state of delivery in January 2002 Certifications Standards and Approvals Certifications The device fulfils the following guidelines and certifications e EU guideline 73 23 EEC on low voltages e EU guideline 89 336 EEC on electromagnetic compatibility e Underwriters Laboratories UL to Standard UL 1950 e Canadian Standard Association CSA to Standard C22 2 No 950 Standards and Approvals The device fulfils the requirements for the CE approval Approvals for UL and CSA are available
101. rking Memory The memory in which a program is stored which can be processed Also known as main memory Write Protection Write protection for files or diskettes e Write protection for files this type of write protection is stored in the computer and is allocated by the system manager e Floppy disk write protection for 3 1 2 in diskettes by opening the write protection hole SIMATIC Field PG Manual Glossary 16 A5E00075760 04 Index A Authorization 3 9 B Batterry replacing 3 5 Battery 2 22 3 5 disposal 3 6 Batter operation 3 5 BIOS Setup Boot Menu 5 19 built in the type of disk drive 5 6 date 5 6 Exit Menu 5 22 Memory Cache Menu Structure Power Menu 5 17 5 16 Security Menu Version menu 5 21 C Calibration c cle 3 6 Cardbus Cold Start Commissioning 3 8 Complete restart 3 10 Connecting external monitor 3 12 headphone 3 14 microphone 3 14 Mouse 3 13 USB Devices 3 13 Connection external power supply 3 4 Cursor key 2 11 D Device TE uration 5 1 5 2 Diskettes 2 17 SIMATIC Field PG Manual A5E00075760 04 Display 2 3 Drive LS120 2 6 E Edit EPROM 3 15 Error Diagnostics Expansion 4 1 External power supply 2 21 F Floppy disk drive 2 17 Function Key 2 12 G Gender Changer 7 9 H Hard Disk Drive 2 19 Hardware Information 7 1 I Inbetriebnahme 3 1 Installing memory submodules 4 3 Interface
102. rl Enter gt expands all lt gt and lt gt moves the device up or down Fig 5 13 The Boot Menu This menu lists the boot devices in groups The group with the highest priority is at the top The procedure for changing the sequence is as follows Use the TL keys to select a group and the or keys to move the group to its new position in the sequence Note During booting the boot drive can be selected with the ESC key SIMATIC Field PG Manual A5E00075760 04 5 19 Configuring the SIMATIC Field PG Groups marked can contain more than one device When you select a group marked in this way hit Enter to view the list of devices in the group See the figure below for an illustration Advanced Security Cae Boot Version Removable Devices LS 120 SLIM4 Fig 5 14 The Boot Menu This screen shows all possible boot devices within a given group the highest priority device is always listed first Here again you can change the sequence as described above If a boot device is not available the next device in the sequence is automatically checked to ascertain whether or not it is bootable SIMATIC Field PG Manual 5 20 A5E00075760 04 Configuring the SIMATIC Field PG 5 7 The Version Menu This menu contains the information you will have to quote when you send us technical questions about your system Advanced Security Power Boot Fig 5 15 The Version Menu SIMATIC Field PG Manual A5E
103. s the CD ROM drive Creating an Extended FAT 32 Partition 8 2 3 In order to create an extended partition you have to boot from the Recovery CD as described above in steps 1 to 4 Create an extended DOS partition for the rest of the disk space Under Windows 2000 the FAT 32 file system can be changed to a NTFS file system with the Format function Creating Partitions under Windows NT After installing a new hard disk it is necessary to create partitions when they partitions have errors or need to be changed Caution By deleting or creating partitions all saved data is lost on the hard disk All drives on the hard disk will be erased The hard disk is delivered with the following installed only for versions delivered with Windows NT apartition of with the FAT16 file system with 2045 Mbytes apartition of with the NTFS file system SIMATIC Field PG Manual A5E00075760 04 8 5 Reinstallation of the Software To restore the partitions to their original condition please do the following Primary Partition 8 6 1 To boot from the Recovery CD proceed as follows When the message Press lt F2 gt to enter Setup appears on the screen press the ESC key After initialization a boot menu to select the boot options is displayed Select ATAPI CD ROM Drive When Microsoft Windows 98 Startup Menu is displayed select 2 Boot for FDISK FORMAT or Windows NT Setup Start the Micros
104. screen displays after power on for example PhoenixBIOS 4 0 Release 6 0 A5E0001xxxx ES00x Copyright 1985 2000 Phoenix Technologies Ltd All Rights Reserved SIEMENS Field PG CPU Intel R Mobile Pentium R III processor 700MHz 640K System RAM Passed 61M Extended RAM Passed 256K Cache SRAM Passed System BIOS shadowed Video BIOS shadowed UMB upper limit segment address xXxxx Mouse initialized Fixed Disk 0 FUJITSU MHK2060AT ATAPI Removable Drive LS 120 S200 02 UHD Floppy ATAPI CD ROM TOSHIBA CD ROM XM 1902B Press lt F2 gt to enter SETUP Notice All information on on screen displays and menu displays are samples Deviations to this example are possible Press the F2 key while the above display is shown to select the ROM based BIOS setup program In this program you can set a number of system functions and hardware configurations of your programming device The standard settings are effective on delivery You can change these settings using the BIOS setup The modified settings become effective when you have saved them and terminated the BIOS setup SIMATIC Field PG Manual A5E00075760 04 5 3 Configuring the SIMATIC Field PG The following screen form appears when you start the BIOS setup Header Advanced Security Power 21010 Version Menu bar Item Specific Hel RE 35 32 p P System Date 09 05 2000 lt Tab gt lt Shift Tab gt or Diskette A Disabled lt Enter gt selects field Prim
105. sor receives an interrupt it suspends its current operations saves the status of its work and transfers control to a special routine known as an interrupt handler This routine processes an instruction set to deal with the particular situation that caused the interrupt Interrupts can be generated by various hardware devices to request service or report problems Interface e An interface is the connection between individual hardware elements such as PLCs programming devices printers or monitors via physical connections cables e An interface is also the connection between different programs to enable them to work together Interface Module Module which controls and extends the hardware periphery SIMATIC Field PG Manual A5E00075760 04 Glossary 7 Glossary IRQ ISA JEIDA K Keyboard LCD LED LPT1 Port Glossary 8 Acronym for interrupt request One of a set of possible hardware interrupts identified by a number The number of the IRQ determines which interrupt handler will be used In the AT bus ISA and EISA 15 IRQs are available Each device s IRQ is hardwired or set by a jumper or DIP switch Industrial Standard Architecture bus for expansion modules Japanese Electronics Industry Development Association Association of Japanese electronics manufacturers whose aim is to set up standards worldwide for the miniaturization and flexible application of PC expansion cards Cooperates with PCMCIA A
106. t Settings gt Control panel gt Field PG You can find additional support during operation in the respective Online Help SIMATIC Field PG Manual A5E00075760 04 3 11 Configuring And Operating The SIMATIC Field PG 3 6 Connecting Peripheral Devices Connecting External Monitors You must switch the PG off before you connect the monitor cable You will find further information about the connector pin assignment in Chapter 7 N VGA socket 7 Fig 3 3 Connecting the Monitor To connect the monitor proceed as follows Switch off the SIMATIC Field PG and the monitor Open the port cover on the rear of the device Plug the monitor cable into the VGA socket connector Secure the connector with the screws Plug the other end of the monitor cable into the monitor Switch on the SIMATIC Field PG and the monitor Make the necessary changes in the SETUP program Menu gt Main gt Hardware Options CRT enabled LCD enabled SIMULTANEOUS N O O fF W N a Note Default setting is simultaneous operation of the flat screen display and of an external monitor The display unit is optimized for a format of 1024 768 pixels Modes with lo wer resolution and text mode are expanded to this format You can optimize the ex
107. ted with the SIMATIC Field PG Whenever the hard disk is accessed the status LED for external storage media at the keyboard front lights up Caution Drives are sensitive to vibrations and shock Any vibrations occurring during ope ration can result in loss of data or damage the drive Optical Drive Depending on the device configuration it can come with a CD ROM a DVD ROM or a DVD ROM CD RW drive For example you can read the electronic manual of the supplied Backup PG CD with this drive Opening the Drawer Switch on the programming device By briefly pressing the eject button the drawer springs out slightly Now pull the drawer out until it clicks into position Inserting Removing CDs Now insert the CD in the drawer with the labeling face up and press it firmly down into the center of the turntable To remove the CD hold it by the edges and pull upwards Closing the Drawer Push in the drawer until it closes completely Do not press the eject button Emergency removal By pushing a pin into the emergency release opening for example a paper clip while the device is switched off you can force the drawer to open SIMATIC Field PG Manual A5E00075760 04 2 19 Getting Familiarized with the SIMATIC Field PG Notice To ensure that the open drawer of the CD ROM drive is not exposed to excessive force always support the front of the drawer with one hand while inserting or re moving the CD ROM with the other
108. ternal monitor display via BIOS Setup in the Main menu item Hardware Options or the setting CRT LCD selection CRT enabled Caution Ensure that the used monitor is suitable for the set resolution and refresh rate SIMATIC Field PG Manual A5E00075760 04 Configuring And Operating The SIMATIC Field PG Connecting Devices to the USB Interface You can connect single or multiple USB devices mouse keyboard or printer to one USB interface connector 1 Open the port cover on the rear of the device 2 Plug the USB device cable into the USB interface The Plug and Play operating system recognizes the device and makes it available If you wish to connect more than two USB devices you must use a HUB Only one of the interfaces can be used as high current source refer to the AppendiiB Technical Data g O USB connector USB connector Fig 3 4 USB connectors Note Devices that do not have a USB plug for example printers can be connected to the USB interface via adapter Using a Mouse You can connect a USB mouse parallel to the Touchpad SIMATIC Field PG Manual A5E00075760 04 3 13 Configuring And Operating The SIMATIC Field PG Connecting a Microphone The 3 5 mm phono
109. th a bootdisk the transfer of the data takes place using the program OEMSETUP EXE To do this start the program OEMSETUP EXE on the recovery CD and continue the sequence as of point 5 lf there is no operating system installed then please do the following 1 Insert the Recovery CD in the CD drive and turn on the programming device 2 To boot from the Recovery CD press the ESC key at the BIOS message Press lt F2 gt to enter Setup After completing the initialization a boot menu screen appears in which you can select the device to be booted from 3 Select ATAPI CD ROM Drive 4 Select 1 Boot for CD Recovery in the screen Microsoft Windows 98 Startup Menu 5 You have to confirm the SIEMENS End User License Agreement with the F8 function key Pressing ESC allows you to decline the agreement and cancels the installation 6 In the next screens you can select the components which are to be copied from the CD to the hard disk At the very least it is necessary to copy the folder 1386 to install or setup Windows 2000 SIMATIC Field PG Manual A5E00075760 04 8 9 Reinstallation of the Software 7 A selection of disk drives for the data transfer is next offered The disk drive selected is not the installation drive for Windows It is the drive on which the necessary installation files and extensions are saved You need approximately 500 MB of additional memory for the Windows setup following the transfer
110. there is a risk that it will fall over and that sensitive components of the unit get damaged SIMATIC Field PG Manual A5E00075760 04 Getting Familiarized with the SIMATIC Field PG Front view with open display 1 Display The Field PG S 14 1 TFT display has a resolution of 1024 x 768 pixels with up to 256k colors 2 Stereo Loudspeaker The speaker outputs audio and system alarm signals generated by the software The loudness is adjusted via speaker icon in the task bar or in the Windows Start menu via Programs gt Accessories gt Multimedia gt Loudness 3 Keyboard The keyboard is split into three key areas the alohanumerical keyboard with special keys the function keys and the control keys 4 Mouse buttons You can use the left or right mouse button to select menu items or process text or graphic objects after having marked the respective object SIMATIC Field PG Manual A5E00075760 04 2 3 Getting Familiarized with the SIMATIC Field PG Rear view 2 4 5 Touchpad The Touchpad has a pressure sensitive surface for precise mouse pointer positioning 6 On Off button Power Button Use the On Off pushbutton to switch on the Field PG into active state or to switch it from active to inactive state Off Standby or Hibernate The Power Button can be parameterized in Wind
111. time needed to boot the system SETUP prompt Enabled POST Errors Enabled Floppy check Disabled Summary screen Disabled Fig 5 5 Boot Options Submenu Quick Boot Some hardware tests are skipped to speed up the boot procedure Mode SETUP prompt The message PRESS lt F2 gt to enter Setup appears at the bottom of the screen during the system run up phase POST Errors The boot process is stopped if an error is detected you must press F1 to confirm Enter Disabled to avoid the necessity of acknowledging errors for example if no keyboard is connected Floppy check The floppy head is stepped inward and then back to its original position during the system run up phase This test is useful because it reinitiali zes the drive Summary The most important system parameters are displayed when the system screen run up phase completes Enabled means that the feature is active Disabled means that the feature is inactive SIMATIC Field PG Manual A5E00075760 04 5 9 Configuring the SIMATIC Field PG Example of a Summary screen PhoenixBlOS Setup Utility Fig 5 6 Summary Screen The Summary screen appears when the system run up phase completes SIMATIC Field PG Manual 5 10 A5E00075760 04 Configuring the SIMATIC Field PG Option Keyboard Features The following submenu appears when you select the Keyboard Features field in the main menu NumLock K Fig 5 7 Key
112. tion 3 3 The red battery LED and_an acoustic warning sounds to warn of pending total di scharge see Section 3 3 Please note that you must disconnect the power cord to separate the device totally from mains You can check the battery status directly on the battery pack Press the marked spot on the battery briefly The status is then displayed by the four LEDs Warning Do not disassemble or mutilate may cause burns Do not incinerate or heat may cause burns exposion or release toxic materials Do not short circuit may cause burns Keep away from children SIMATIC Field PG Manual A5E00075760 04 Configuring And Operating The SIMATIC Field PG What Does This Chapter Contain The chapter below describes all tasks required to successfully set up your workplace These include e initial steps for commissioning your SIMATIC Field PG e working with battery operation and replacing the battery e connecting peripheral devices e working with memory submodules for the PLC and e connecting your PG to other devices Chapter Overview ZN Secon o eseon ae ld PG w Networking the Field PG with Other Stations on PROFIBUS Ethernet RJ45 Ethernet Interface Warning When connecting long signal lines especially for plant wide connections make sure that the signal lines are connected to the local equipotential grounding system cable shield connected to protective conductor SIMATIC Field PG Manual A
113. ton Notice The Windows NT versions do not support the standby and hibernate operating modes After shut down the Field PG always has to be switched off via the Power Button Hold down the On Off pushbutton for more than 7 seconds to trigger the Override function The device is switched off Note Via Setup gt Control Panel gt Power Management under Windows Me and Win dows 2000 you can parameterize the reaction of the On Off pushbutton and of the display lid To isolate the unit totally from the power supply system you must unplug the patch cord and remove the rechargeable battery SIMATIC Field PG Manual A5E00075760 04 2 15 Getting Familiarized with the SIMATIC Field PG Caution The Field PG supports different operating modes according to the settings in the Windows power options The power options are preset at the factory in such a way that the device always switches to defined operating modes On Standby Hiber nate Off When changing these settings or updating the device with additional hardware for example USB components or additional software the operating modes can be influenced in such a way that the device can no longer switch to the hibernate or standby mode Although the screen is dark relevant components remain active and consume power Before transporting the Field PG in the carrying case always shut it down or set it to hibernate mode You can recognize these modes when all status LEDs are
114. u can select the boot options Select ATAPI CD ROM Drive 3 When Microsoft Windows 98 Startup Menu is displayed select 2 Boot for FDISK FORMAT or Windows Me Setup Start the Microsoft Windows Me hard disk configuration program with A gt FDisk In the dialog box select Yes in Activate Support Y N YP to enable large disk support for FAT32 partitions Create a primary DOS partition with at least 4090 MB For FAT32 partitions enter N for No for the question Do you want to use the maximum memory size available for the primary DOS partition and do you want to activate this partition and set the partition size for example to 6100 MB SIMATIC Field PG Manual A5E00075760 04 8 3 Reinstallation of the Software Creating an Extended Partition 8 2 2 In order to create an extended partition you have to first boot from the Recovery CD as described in steps 1 to 3 above Using A gt FDisk start the Microsoft Windows Me hard disk configuration program Select the dialog box for large disk support Do you wish to enable large disk support Y N Y for Yes Create an extended DOS partition for the rest of the disk space Creating Partitions under Windows 2000 After installing a new hard disk it is necessary to create partitions if the partitions contain errors or need to be changed Caution All stored data is lost when you delete or create
115. with Micro Memory Cards is supported by STEP 7 V5 1 or higher ly J A GS Ga Gas GD T Ca Ca C rmp AD a Micro Memory Card Fig 3 9 Slot for Micro Memory Cards Proceed as follows when working with Micro Memory Cards 1 Switch on your device 2 Start your SIMATIC programming function 3 Insert the Micro Memory Card into the slot on the side of the device The card s connector is encoded for insertion in one position only with inclination to the rear A symbol on the PG housing indicates the plug in direction 4 Read program or erase the Micro Memory Card with the programming function of your SIMATIC programming software 5 Close the programming function of your SIMATIC programming software 6 Remove the Micro Memory Card from the interface Caution You must not remove the SIMATIC Micro Memory Card while the module pro gramming status display is lit Always discharge your body s static electricity by briefly touching a grounded part of the device before you insert a SIMATIC Micro Memory Card Note Parallel operation of a Micro Memory Card MMC and of a Memory Card is not possi ble The PG is equipped with a priority circuit that switches off the MMC interface when a Memory Card is inserted The internal MMC is switched off as soon as a
116. y buffers often used data to increase the speed of access The computer has two cache levels Cardbus interface This interface is compatible with 32 bit Cardbus Cards with PCI performance compliant with the PC Card standard CD ROM Compact Disc Read Only Memory Removable memory for large amounts of data Click Pressing and immediately releasing the left mouse button selects objects or triggers commands COM1 Port Serial V 24 modem PLC interface This interface is suitable for asynchronous data transmission It can also be used to connect printers with a serial interface SIMATIC Field PG Manual A5E00075760 04 Glossary 3 Glossary COM2 Port Serial RS 232 interface which can be used to connect a mouse or a printer Configuration Files These are files containing data which define the configuration after booting Examples of such files are CONFIG SYS AUTOEXEC BAT and the registry Configuration Software The configuration software updates the device configuration when new modules are installed This is done either by copying the configuration files supplied with the module or by manual configuration using the configuration utility Controller Integrated hardware and software controllers that control the functions of certain internal or peripheral devices for example the keyboard controller Cursor Collective term for mouse pointer and text cursor Cursor Control Keypad on the keyboard for controlling the curso
117. zation by selecting All Notice The authorization diskette supplied with the PG contains authorizations for the SIl MATIC software you ordered only The SIMATIC software you receive will corres pond to your order form The diskette of the supplied version Upgrade Installation contains only the soft ware for upgrading authorizations already preinstalled Software without authorizations in the in the scope of supply cannot be used when installed on the PG Keep the Authorization disk in a safe place so that you can save the authorizations to disk software You can now install the the supplied operating software for the DVD ROM or the DVD ROM CD RW drive Place the CD in the drive and follow the instructions on the screen SIMATIC Field PG Manual A5E00075760 04 3 9 Configuring And Operating The SIMATIC Field PG 3 4 2 Restart of the SIMATIC Field PG Once the Field PG is configured the user interface of the corresponding operating system is displayed following system startup every time you switch on or reset the PG Starting SIMATIC Software Programs 3 10 STEP 5 not available on all delivered versions e Click Start on the Windows button and select the desired program choosing Simatic gt STEP 5 Please note that you have to install the authorization disk before you start working with STEP 5 see Sectior 3 4 1 Notice When you use the P Tools for editing PCP M files supplied with STEP 5 remem

Configuring the SIMATIC Field PG - Internet

Contents

Download Pdf Manuals

Related Search

Related Contents