AT-216F _A1.cdr
Contents
1. actual range may differ from theoretical range User should adjust the emission level based on actual environment as wireless signals may be affected by environmental factors Therefore it is not unusual if the displayed distance differs to some extend from the actual distance in some surroundings a Additional Information for terms of use and limitation of liability 1 Terms of Use This product is offered to you conditioned upon your acceptance without modification of the terms conditions notices contained herein Usage of this product implies acceptance of all such terms conditions and notices 2 Proper Use This product is designed for use with dogs where training is desired The specific temperament of your dog may not work with this product We recommend that you not use this product if your dog is less than 8 pounds or if your dog is aggressive If you are unsure whether this is appropriate for your dog please consult your veterinarian certified trainer or contact our customer support 3 No Unlawful or Prohibited Use TM A Aetertek pi ireless Do at Fence Syste F This product is designed for use with dogs only This dog training device is not intended to harm injure or provoke Using this product in a way that is not intended could result in violation of Federal State or local laws 4 Limitation of Liability In no event shall Aetertek be liable for any direct indirect punitive incidental special or cons2. User s Manual for Aetertek Wireless Dog Cat Fence System AT 216F Aetertek Training Systems 2 0 50 Diameters www aetertek com 7 owner s manual Made in China All Rights Reserved AT 216F Index DUGG Shadi tases a en ae no a a 1 2 Opera tiie GLUO RRE ee ees 9 4 5 6 Adjusting Control Rahe lt 6 7 Terms or Use amp uitation oc Liability nn 8 9 Contact Ue TSn SS eee 9 TM Aetertek py Training Systems Wireless Dog Cat Fence System AT 216F Antenna Assemble The Antenna Onto Transmitter Beep Icon Vibrate Icon Diameter level Signal Icon Will flash in emitting Up Arrow Increase Diameter Left Arrow Button Decrease Beep Vibrate Shock levels or switch Auto or Manual mode In programming Down Arrow Reduce Diameter Main Supply Port Shock Icon Auto Mode Manual Mode Diameter Covered Battery Remained Menu button Enter amp Quick program setting Quick press menu button once will enter Beep setting it also can go cycle from beep vibration to shock setting by quick press Left or Right arrow buttons you can turn on or turn off Beep Vibrate or Shock by Up or Down button under shock function there have auto or manual mode you can go Cycle from auto mode to manual 00 10 manual by up or down arr
3. ashes the BB sound vibration and shock can be programmed by pressing the up and down buttons ON means relevant function selected OFF means relevant function deselected Two Shock modes AUTO and MANUAL In Auto Mode transmitter emits certain level shock intelligently while in the mode of MANUAL user can set the desired shock levels As soon as function and level is set press the menu button can save the setting and exit programming Open the package take out the receiver and install the W metal prongs charges the receiver for the first use To prolong battery life recommend to charge the receiver about 3 5 hours for the first few charges 1 When receiver is connected to the wall charger it will beep and vibrate once and the red LED light will be on This is to indicate the receiver is in charging status Receiver will be charged in full after 3 4 hours with the blue LED light on When unplugged receiver will beep and vibrate once Note please don t forget to replace the charge port cover lid 2 Press and hold Power button for 3 seconds receiver will beep and vibrate once to indicate receiver is powered on If the transmitter is on standby the receiver will pair sync with the transmitter automatically At this point the system is on working status TM A Aetertek pi ireless Do at Fence Syste F 3 Do a self test by pressing the power button 3 times The receiver will beep vibrate and discharge shock No
4. equential damages or any damages whatsoever arising out of or connected with the use or misuse of this product Buyer assumes all risks and liability from the use of this product 5 Modification of Terms and Conditions Aetertek reserves the right to change the terms conditions and notices under which this product is offered For parts and warranty contact with authorized dealer shown in warranty card
5. ow button then one more quick press menu button will save the program Right Arrow Button Increase Beep Vibrate Shock Level Or switch Auto Or Manual Mode in programming ik rt R iver Quick Start Guidance 1 Assemble transmitter plug charger supplied into Test Kit main supply then transmitter will be in working status you can put transmitter on the place you find appropriate according to the boundary and your actual conditions it will go into auto mode in default program you can also set those TM o Aetertek bs Training Systems Wireless Dog Cat Fence System AT 216F Charging Port 2 3hours full charge S Blue light It will turn on after full charged Red Light 1 it will turn on after plugged in main supply functions manually 2 Charge receiver first screw shock prongs 2 it will turn on after turned on it will go off when matched 3 It will flash if it go out of the signal area onto receiver put Straps onto strap port then receiver will be communicated with transmitter automatically 3 Mark your boundary with those flags supplied along the circle covered by the signal from transmitter 4 wear receiver around your dog s neck then this system will be workable covered ON OFF Button Press and hold on three seconds will turn receiver off when it is turned on short press by three times will do seft test receiver will beep
6. vibrate and shock by one time Wireless Dog Cat Fence System AT 216F 1 Open the package take out the transmitter align the RF antenna at the RF connector rotate clockwise and tighten the nut 2 Plug the charger into the DC jack of the transmitter the transmitter will standby of emission the antenna symbol in the display starts flashing indicating the transmitter is ready The lower right corner shows the current power 3 The transmitter coverage distance can be adjusted by up and down buttons the center of the display shows the current distance between the emission level and reference signal coverage Adjust the level according to user needs Level 00 10 is the strength level display of coverage signal the higher the value is the larger the coverage distance is The center of the display will show the reference distance range of the current level note in some special environment when there is difference between TM Aetertek pi ireless Do at Fence Syste F the reference distance range and the actual distance the signal coverage range can be adjusted by intensity increase decrease according to user needs 00 level is the way of turning off electric shock 4 To enter or exit menu setting by pressing M button On the menu the BB sound vibration and shock function can be selected by left and right buttons When setting menu icon fl
7. w it is ready to let your dog wear the receiver Thread the collar straps through the clasps adjust the length to fit the dog s neck so it will not make the dog feel uncomfortable To ensure ideal shock effect the collar s prongs should have direct contacts with the dog s skin TM Aetertek by Training Systems Wireless Dog Cat Fence System AT 216F The emission signal The emission signal The EU Mee The emission signal covers the middle covers the left side COVETS ME night covers the backyard Marked Out Boundary With Flags 3 Refer to the diagram Red light flashing means the signal out to place the flags of coverage place a flag at this point 150 300CM a flag to mark the periphery of the coverage Detect the signal coverage strength TM A Aetertek pi ireless Do at Fence Syste A F Training the dogs to stay inside the control zone Set the transmission level test the receiver based on reference distance range when it is near the periphery the red LED starts flashing the closer to the periphery the faster the beep sound will be made and then triggers the vibration if the pet is near the boundary even further the electric shock will be discharged If the pet returns to the control zone corrections will stop Place the flags where the warning is sent which will set a boundary of the control zone with all the warning spots flagged Dogs will learn to respond after training Please be advised the
Download Pdf Manuals
Related Search