User Manual
Contents
1. MD BSL15W SPRING LOADED TWIN ARM MONITOR MOUNT For 15 27 38 1 68 6 cm LCD desktop computer User Manual 2 Thank you for choosing Gabor The Gabor MD BSL15W mounts two 15 27 38 1 68 6 cm LCD computer monitors side by side It attaches to the edge of your desk via a built in clamp freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands The MD BSL15W s arms incorporate an internal mechanical spring system which is safer than the gas springs found in similar products These spring loaded arms function as a counterbalance to support your monitors in any position Multiple points of articulation provide a full range of motion making it easy to adjust your monitors height tilt swivel and roll Welcome k pa e 4 Overview Support bracket Set screw Sue collar Clamp Overview Shaft cap DT Mounting pegs Locking Clamp screws Clamp locking knob Mounting Arm x2 VESA mount Mounting Socket Tools Required For Installation Phillips screwdriver Also Included Supplied Ports amp Hardware A 8 M4x1 screws B 8 M4x30 screws C 2 M6xe5 screws D 3mm hex key E 5mm hex key F 8 Spacers G Cable clip H 2 Protective caps Shaft cap J User manual Bc M4 M6 Hex Keys ES Protective Caps e x8 e x2 e x eo x8 E xe2. Wb Ip e x8 e x o xl lt Installed in shoft Overview s 6 Product Specifications Monitor display size 15 27 38 1 68 6 cm Maximum load capacity per arm 17 Ib 7 8 kg VESA standards 75x75 100 x 100 Tilt 90 85 Swivel 180 Roll 360 Installation Clamp fits desk edges up to 2 6 6 5 cm thick Arm width extended 28 7 73 cm Arm pivot 180 Armheight adjustment Angle 45 Range 0 13 8 0 35 cm Shaft height 12 2 31 cm Weight 8 25 Ib 3 7 kg Specifications Max 28 7 73 cm gt W gt GE 0 8 E O E e W TE d dl Safety Warnings Il Please read and follow these instructions and keep this manual in a safe place Clean this product with only a soft dry cloth Keep this product away from children Make sure everything is secure before proceeding Make sure that this product is intact and that there are no missing parts To avoid damage to this product be careful not to overtighten or improperly thread any of the threaded fittings 10 Do not exceed the maximum load capacity Do not install this product on an unsteady structure or one that is prone to vibration has a chance of being impacted or is susceptible to other movements Reinforce the structure as necessary before installing this product ounting surfaces should be sturdy and flat Do not install this product on a we
3. e Lock the collar in place by rotating it until fully tightened 1l Installation Instructions 12 Attaching Your Monitor to the VESA Mounts Before attaching your monitor to the VESA mount you may need to detach your monitor s built in stand For information on how to do this consult your monitor s user manual Depending on how the back of your monitor is configured you can use one of two methods to install the VESA mount onto your monitor flush or recessed If your monitor s VESA mounting holes are flush with the rest of the monitor use the Flush Installation instructions below If your monitor s VESA mounting holes are in a recessed area of the monitor use the Recessed Installation instructions on page 14 Installation Instructions Flush Installation Note Before stortino make sure the VESA mount mounting arm and monitor are facing the proper direction l Carefully place your monitor facedown on a flat surface Tip To avoid scratching the screen place your monitor on a soft cloth such as a towel Align the mounting holes in the VESA mount with the corresponding mounting holes in your monitor Insert four of the M4xl2 screws the smallest of the included screws into the VESA mount and use a Phillips head screwdriver to fasten them until fully tightened Repeat these or the other set of installation steps as necessary for your second monitor and continue to Mou
4. your desk you can remove the bottom part of the clamp If this is the case skip to Limited Clearance on page 10 Clearance l Loosenthe clamp locking knob until you can fit the clamp over the edge of your desk 2 Fit the clamp over the edge of your desk and tighten the clamp locking knob until the shaft is securely mounted to your desk Continue with Adjusting the Support Bracket on page 11 Installation Instructions 9 10 Limited Clearance d Use the included 5 mm ex key to remove the amp screws h C Fit the top part of the clamp behind your desk U a nderneath your desk ign the screw holes in the top and bottom parts of the clamp Note It may help to unscrew the clamp locking knob first Installation Instructions Ul Reinsert the clamp Screws and use the included 5 mm hex key to fasten them until fully tightened Tighten the clamp locking knob until the shaft is securely mounted to your desk Continue with Adjusting the Support Bracket on page ll Adjusting the 3 Slide the support bracket Support Bracket along the shaft so it rests on the locking collar pe l Rotate the locking collar and use the included 3 to loosen it and then mm hex key to fasten slide the collar to the the set screw until fully approximate height at tightened which you want to mount your monitors 4 Insert the shaft cap into the top of the shaft
5. Insert your monitor cable into the cable guides on the underside of the mounting arm Repeat these steps for the other monitor arm assembly and use the included cable clip to secure your monitor cables to the shaft Installation Instructions 15 Adjusting Tension and Articulation Note To avoid damage make sure to hold your monitor steady when making any adjustments 16 Installation Instructions Arm Tension Important The arm tension is preset for lighter monitors To avoid damage do not continue to loosen the screw if it s already loose To prevent your monitors from drooping you can adjust the tension of the mechanical spring in the mounting arms Use the included 5 mm hex ey to adjust tension Rotate clockwise to increase tension for heavier monitors and counterclockwise to reduce tension for lighter monitors Arm Swivel You can adjust the arms horizontal swivel action via the set screws on the rear of the mounting sockets Position the arms as desired and use the included 3 mm hex key to fasten the set screws until fully tightened Monitor Tilt and Swivel You can adjust the vertical tilt and horizontal swivel action of your monitors for optimal viewing comfort Position your monitors as desired and use the 5 mm hex key to fasten the set screws until fully tightened Installation Instructions 17 18 Customer Support For more information or to arrange servi
6. ak uneven surface All photos are for illustrative purposes only Safety Warnings 7 8 Available separately are two dedicated accessories for this mounting system the MWD E8W extension arm and the MW C wall mount The MWD E8W extension arm adds 10 25 4 cm of length and an additional point of articulation to provide greater freedom for positioning your monitor The MW C wall mount offers an alternative mounting option for your MD BSL15W dual monitor setup MWD E8W Getting Started Getting Started Decide where you want to place your monitors When using a dual monitor setup ike this one position your primary monitor directly in front of you and your secondary monitor to the side You shouldn t need to turn your head to look at your primary monitor Both monitors should be at eye evel approximately at an arm s length away If you have to strain to look at either monitor readjust its position Attaching the Shaft The MD BSL15W easily attaches to most desk edges up to 2 6 6 5 cm thick even if your desk is nearly flush against a wall Before attaching the shaft to your desk determine whether you have enough room to fit the entire clamp behind your desk If you have enough clearance to attach the clamp without removing the bottom part of it skip to Clearance on this page f your desk is close to a wall or you don t have enough clearance to fit the entire clamp behind
7. ce visit www madebygabor com or call Customer Service at ele 594 2353 GABOR A Gradus Group Brand Product warranty is provided by the Gradus Group www gradusgroup com Gabor is a registered trademark of the Gradus Group 2014 Gradus Group LLC All Rights Reserved Customer Support Warranty ONE YEAR LIMITED WARRANTY This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one 1 year from the original purchase date or thirty 30 days after replacement whichever occurs later The warranty provider s responsibility with respect to this limited warranty shall be limited solely to repair or replacement at the provider s discretion of any product that fails during normal use of this product in its intended manner and inits intended environment Inoperability of the product or part s shall be determined by the warranty provider If the product has been discontinued the warranty provider reserves the right to replace it with a model of equivalent quality and function This warranty does not cover damage or defect caused by misuse neglect accident alteration abuse improper installation or maintenance EXCEPT AS PROVIDED HEREIN THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE This warran
8. nting the Arms on page 15 Installation Instructions 13 14 Recessed Installation Note Before starting make sure the VESA mount mounting arm and monitor are facing the proper direction l Carefully place your monitor facedown on a flat surface Tip To avoid scratching the screen place your monitor on a soft cloth such as a towel Installation Instructions Place four of the included spacers on each of your monitor s four VESA mounting holes Align the mounting holes in the VESA mount with the four spacers Insert four of the included M4x30 screws into the VESA mount and use a Phillips head screwdriver to fasten them until fully tightened Tip Thread each of the Screws by hand before fastening them with the screwdriver Repeat these or the other set of installation steps as necessary for your second monitor and continue to Mounting the Arms on page 15 Mounting the Arms l ift the arm monitor ssembly and mount it nto one of the mounting egs on the aluminum racket tro G a Insert one of the included 6x25 screws through the bottom of the mounting arm socket and hold the screw in place so it protrudes from the screw hole 3 Thread one of the included protective caps onto the screw as much as possible and then push the cap into the socket 4 Use a short Phillips head screwdriver to fasten the screw until fully tightened 5
9. ty provides you with specific legal rights and you may also have additional rights that vary from state to state To obtain warranty coverage contact the Gabor Customer Service Department to obtain a return merchandise authorization RMA number and return the defective product to Gabor along with the RMA number and proof of purchase Shipment of the defective product is at the purchaser s own risk and expense Customer Support Warranty 19
Download Pdf Manuals
Related Search