Noco Genius Boost GB30 User Manual
Contents
1. 1 Internal Battery Level Indicates the charge level of the internal battery 2 Error LED lluminates Red if reverse polarity is detected or blinks On and Off when the internal battery temperature is too high 3 Power Button Push to turn unit On amp Off 4 Power LED Illunimates White when unit is On 5 Boost LED lluminates White when Boost is active If the unit is connected properly to a battery the GB30 will automatically detect a battery and go into Boost mode LED flashes White when Manual Overide feature is active 6 Manual Override Button To enable push and hold for three 3 seconds WARNING Disables safety protection and manually forces Boost On Only for use when a battery is too low to be detected 7 Light Mode Button Toggles the ultra bright LED light through 7 light modes 100 gt 50 gt 10 gt SOS gt Blink gt Strobe gt Off When Recharging the GB30 LED 25 Red LED 25 50 75 100 6000 50 Red LED 25 50 75 100 6000 15 Yellow LED 25 50 75 100 000 100 Green LED 25 50 75 100 0008 Explanation The 25 Charge LED will slowly pulse On and Off when the battery is less than 25 charged When the battery is 25 charged the Red Charge LED will be solid The 50 Charge LED will slowly pulse On and Off when the battery is less than 50 charged When the battery is 50 charged2. a NOCO see genius BOOST GB30 User Guide A DANGER PRIOR TO USE READ AND UNDERSTAND PRODUCT SAFETY INFORMATION Failure to follow the instructions may result in ELECTRICAL SHOCK EXPLOSION or FIRE which may result in SERIOUS INJURY DEATH DAMAGE TO DEVICE or PROPERTY Do not discard this information Welcome Thank you for buying the NOCO Genius Boost GB30 Read and understand the User Guide before operating the product For questions regarding our jump starter view our comprehensive support information at www no co support To contact NOCO for personalized support not available in all areas visit www no co connect What s In The Box e GB30 Lithium Jump Starter e 40 Inch Micro USB Cable e 12V USB Charger e X Connect HD Battery Clamps e User Guide amp Information Guide and Warranty Contacting NOCO Phone 1 800 456 6626 Email support no co Mailing Address 30339 Diamond Parkway 102 Glenwillow OH 44139 United States of America About GB30 The NOCO Genius Boost GB30 is an ultra compact and portable lithium ion jump starter for cars boats motorcycles ATVs lawn mowers RVs tractors trucks and more It s extremely safe for anyone to use It features spark proof technology and reverse polarity protection The GB30 can instantly jump start most single battery applications up to 20 times on a single charge The GB30 is also equipped with a USB battery pack and LED flash
3. e GB30 is designed to jump start 12 volt lead acid batteries down to 2 volts If your battery is below 2 volts the Boost LED will be Off This is an indication that the GB30 can not detect a battery If you need to jump start a battery below 2 volts there is a Manual Override feature which allows you to force On the jump start function CAUTION USE THIS MODE WITH EXTREME CARE THIS MODE IS FOR 12 VOLT LEAD ACID BATTERIES ONLY BOTH THE SPARK PROOF AND REVERSE POLARITY PROTECTION FEATURES ARE DISABLED PAY VERY CLOSE ATTENTION TO THE POLARITY OF THE BATTERY BEFORE USING THIS MODE DO NOT ALLOW THE POSITIVE AND NEGATIVE BATTERY CLAMPS TO TOUCH OR CONNECT TO EACH OTHER AS THE PRODUCT WILL GENERATE SPARKS THIS MODE USES VERY HIGH CURRENT UP TO 400 AMPS THAT CAN CAUSE SPARKS AND HIGH HEAT IF NOT USED PROPERLY IF YOU ARE UNSURE ABOUT USING THIS MODE DO NOT ATTEMPT AND SEEK PROFESSIONAL HELP Before using the Manual Override feature make sure the HD battery clamps are connected to the correct polarity battery terminals and the HD X Connect is connected to the GB30 To use the Manual Override feature press and hold the Manual Override Button a red exclamation point icon inside a red circle for three 8 seconds The White Boost LED will flash On and Off indicating you have successfully entered into Manual Override and it is ready to jump start your vehicle If connected in reverse polarity the Red Error LED will
4. e negative first or positive first for positive ground systems Jump Starting 1 Verify the voltage and chemistry of the battery 2 Confirm the HD battery clamps are connected to the correct polarity battery terminals 3 Connect the HD X Connector to the GB30 4 Make sure all of the vehicle s power loads headlights radio air conditioning etc are turned off before attempting to jump start the vehicle 5 Press the Power Button to begin jump starting All LEDs will flash indicating that all LEDs are properly functioning If you are properly connected to the battery the White Boost LED will illuminate If the battery clamps are connected in reverse the Red Error LED will illuminate Reverse the connections to clear this error and then the White Boost LED will illuminate The White Boost LED is illuminated when the GB30 is ready to jump start your vehicle 6 Try starting the vehicle Most vehicles will immediately start Some vehicles may require the GB30 to be connected for up to 30 seconds before starting If the vehicle does not start right away wait 20 30 seconds and try again Do not attempt more than five 5 consecutive jump starts within a fifteen 15 minute period Allow the GB30 to rest for fifteen 15 minutes before attempting to jump start the vehicle again 7 Once you have started your vehicle disconnect the battery clamps and remove the GB30 Low Voltage Batteries amp Manual Override Th
5. illuminate and the unit will not operate CAUTION POWER THE GB30 OFF BEFORE DISCONNECTING THE BATTERY CLAMPS THIS WILL ENSURE YOUR SAFETY REMEMBER BOTH THE SPARK PROOF AND REVERSE POLARITY PROTECTION FEATURES ARE DISABLED Most vehicles will immediately start Some vehicles may require the GB30 to be connected for up to 30 seconds before starting If the vehicle does not start right away wait 20 30 seconds and try again Do not attempt more than five 5 consecutive jump starts within a fifteen 15 minute period Allow the GB30 to rest for fifteen 15 minutes before attempting to jump start the vehicle again Understanding Charge LEDs The GB30 has four 4 Charge LEDs 25 50 75 and 100 These Charge LEDs indicate the internal battery s state of charge SOC See below LED Explanation 25 The 25 Charge LED will be solid Red LED Red when the internal battery is less 25 50 75 100 than 25 charged 000 50 The 50 Charge LED will be solid Red LED Red when the internal battery is less 25 50 75 100 than 50 charged 6000 15 Yellow LED 25 50 75 100 000 100 Green LED The 100 Charge LED will be solid 25 50 75 100 Green when the internal battery is fully charged No other LEDs will be OOO O illuminated The 75 Charge LED will be solid Yellow when the internal battery is less than 75 charged 9 1S008Snue6 7 was User Interface
6. light making it the ultimate emergency tool Getting Started The GB30 comes partially charged out of the box and needs to be fully charged prior to use Carefully read and understand the vehicle owner s manual on specific precautions and recommended methods for jump starting the vehicle Make sure to determine the voltage and chemistry of the battery by referring to your battery owner s manual prior to using this product The GB30 is for jump starting 12 volt lead acid batteries only Connecting to the Battery Before connecting to the battery verify that you have a 12 volt lead acid battery The GB30 is not suitable for any other type of battery Identify the correct polarity of the battery terminals on the battery The positive battery terminal is typically marked by these letters or symbol POS P The negative battery terminal is typically marked by these letters or symbol NEG N Do not make any connections to the carburetor fuel lines or thin sheet metal parts The below instructions are for a negative ground system most common If your vehicle is a positive ground system very uncommon follow the below instructions in reverse order 1 Connect the positive red HD battery clamp to the positive POS P battery terminal 2 Connect the negative black HD battery clamp to the negative NEG N battery terminal or vehicle chassis El 3 When disconnecting disconnect in the reverse sequence removing th
7. lithium battery Due to FCC regulations we recommend not to charge and discharge the unit at the same time Charging Times The time to recharge a GB30 will differ based on the discharge level and the power source used Actual results may vary due to battery conditions USB Charger Rating 5A 1A Time 12h r 6hr Charging Your USB Devices You can recharge virtually any USB device like a smartphone Connect the included USB Charge Cable to the USB OUT port and connect to your USB device The number of times you can recharge a USB device will vary between devices For recharge times contact your device manufacturer LED Flashlight The GB30 has an integrated ultra bright LED flashlight It has seven 7 light modes that effect its performance and longevity 100 50 10 SOS Blink Strobe and Off To turn the flashlight On and Off use the Power button with the light bulb icon Press once to turn the flashlight On at 100 luminosity again for 50 luminosity within 3 seconds again for 10 luminosity within 3 seconds again for SOS within 3 seconds again for Blink within 3 seconds again for Strobe within 3 seconds and again for Off If a light mode is not selected within 3 seconds it will remain On in the current light mode and the next selection will turn the flashlight Off Depending on the mode selection the GB30 will have various levels of output and runtime Selecti
8. ng a lower power level when using the GB30 for extended periods of time will prolong battery life Modes 100 gt 50 gt 10 gt SOS gt Blink gt Strobe gt Off Energy Saving Auto Shut Off The GB30 has a built in energy saving feature that will automatically turn the unit off after seven 7 hours To continue using simply power on the unit again Technical Specifications Internal Battery Lithium lon Dimensions L x W x H
9. the Red Charge LED will be solid The 75 Charge LED will slowly pulse On and Off when the battery is less than 75 charged When the battery is 75 charged the Yellow Charge LED will be solid The 100 Charge LED will slowly pulse On and Off when the battery is less than 100 charged When the battery is fully charged the Green LED will be solid and the 25 50 and 75 Charge LEDs will turn Off Understanding Error Conditions The GB30 shall display an Error Condition when a reverse polarity condition is present a battery below two 2 volts or the internal battery overheating When one of these Error Conditions are present the following will happen Reason Solution Reverse polarity Reverse the battery connections Error LED Solid Red Reason Solution Error LED The internal battery is too ne hot Blinking Red Allow the unit to cool w Cables Connected Bring the unit into cooler Properly environment Boost Light Does Connected battery is below 2 volts Not Come On Remove all loads and w Cables Connected try again or use Manual Properly Override Mode Charging the GB30 Connect the GB30 using the included USB Charge Cable to the USB IN port and the USB car charger It can also be recharged from any USB powered port like an AC adapter car charger laptop and more The USB IN port is rated at 2 1 Amps to ensure safe and efficient charging of the internal
Download Pdf Manuals
Related Search