RS485 Surveillance Keyboard
Contents
1. 30 Zc VV ANT AN TEAS ETE Sa T 31 aro NIPONO lle 31 1 Summary The keyboard is an universal keyboard of security monitoring series which can control integrate dome camera with all kinds of protocols matrix and DVR which has been equipped with 3D joystick and 2D joystick which can control the revolving of the camera and the zoom magnification of lens with the LCD screen and the function of back light which can display the current operation order the control protocol name the current dome ID the current monitor ID and the state of joysticks The user can control the CCTV system more easily with the joystick and the LCD screen 1 1 Notice e Please read the manual carefully and reserve it e Please advert to the notice in manual e Please don t place the keyboard in the moist place e Please don t close up the keyboard to exothermic object for long time 1 2 Function and Characteristic e RS485 Bus Line and a keyboard can connect 31domes at most in the direct control mode e It can be compatible with all kinds of protocols e You can control the Iris Locus and Zoom e You can set and call the preset run scan pattern and tour e You can control the matrix and through which can control the dome indirectly e It has been equipped with the 2D 3D joystick and the larger LCD screen 1 3 Technical Data e Electrical Input voltage 9V 12VAC DC Rated power 2 5W Communication Communication interface RS2. LCD display is used to list the basic information of keyboard operation which involves 8 controlling camera monitor ID baud rate and soon In the last line there are keyboard input commands and joystick operation As the right picture shows When operate it LCD will turn on back light in order to operate easily stop to operate it for 15 s back light will be off automatically CamiD 001 Mon ID 001 Protocol Factory Baud rate 9600bps Picture 3 1 2 3 3 Joystick controls the dome Joystick has two functions one is manually con trolling dome rotation the other is setting controlled object menu e Rotate joystick at any directions the dome will rotate in correspondence with directions at the same time LCD displays the information as lower right corner shows 4 they respectively show tilt up tilt down tilt right tilt left If the joystick tilts upper right corner the screen will display such information joystick return to the primary location and the dome immediately stop to rotate e The joystick tilt up means choosing previous menu which is down means choosing next menu if it is used to set the menu the joystick is right means entering the next menu or reserving setting after set which is left means exit or stop reserving e More pan tilt to joystick the more fast speed the dome rotates Control the pan tilt to joystick it can control the rotation speed of dome 3 4 Change object dom
3. then press 0 then press PAT TERN the pattern setup finish e Run pat tern N PATTERN J Input pattern number 1 4 press PATTERN run pattern 3 6 4 Tour 10 Run tour N TOUR TOUR Press tour number press TOUR run tour If system has only a tour press TOUR directly Set tour must enter setup menu 3 7 Cal the dome main menu 9 0 1 input 90 then press Preset to call the main menu of object dome and the menu is displayed the object monitor How to set the dome menu by keyboard Please refer to the dome Operation manual 3 8 Control the matrix 3 8 1 Switch the domes in order The matrix connects sixteen domes and switches the dome to previous and next dome The LCD will display NO date and time PREV Switch to previous dome Press PREV switch to previous dome in single step Press PREV to hold it for 2s and jump sixteen domes of the connection matrix in previous order Press Stop to stop to switch NEXT Switch to next dome Press NEXT switch the next dome in single step press NEXT to hold it for 2s and jump the sixteen domes of the connection matrix Stop switch continuously press Stop to stop to switch 3 8 2 Call main menu of matrix Shift Set Call the main menu and the menu will be displayed in the object monitor How to set the matrix menu by keyboard Please refer to the matrix operation manual 3 8 3 Confirm after pr
4. second item Set right limit same operation as left limit Back to scan menu then press 3 to run scan A After entering the set ting dome pattern menu the joys tick will control the dome directly at this time the keys in lens controlling area also can control 4 N the dome lens the operation of the joystick and the key is invalid for the NOTICE dome under general menu mode 4 2 3 Pattern setting Enter the menu as LCD shows picture 4 1 1 1 Move the joystick to 2 to enter the dome setting menu as LCD shows Picture 4 2 1 1 Move the joystick to 3 to enter the pattern setting menu as LCD shows picture 4 2 3 1 1 Pattern num _ 2 Set pattern 3 Run pattern Picture 4 2 3 1 After entering the menu the system requires in putting pattern tour that you set in the first item the input range is 1 4 press Enter to confirm the cursor will auto jump to the second item to start setting pattern if user has finished to set pat tern already you can jump over this item and choose 3 to run pattern directly Pattern setting after entering the pattern menu to move the dome in an appropriate position press 1 to start tore cord pattern tour LCD will show Start as picture 4 2 3 2 shows Press 1 to start Press O to stop Press prev to back Picture4 2 3 2 21 After entering the set ting dome pat tern menu the joystick will control the dome dire
5. select Multi keyboard state tilt up down the joystick to set the state as ON or OFF the default setting of keyboard is OFF as it set as it can support multi keyboard work there is non interference between them one group can support 4pcs keyboard mostly as Multi keyboard stat e is opened if there is only a keyboard to work the key board address must be set as 1 or the keyboard can t be controlled In multi keyboard state the baud rate of each keyboard should 5 be set as 9600bps NOTICE 4 1 5 Keyboard screen brightness Enter the main menu LCD display sees to the picture 4 1 1 2 Move the joystick to 2 to set screen brightness LCD display sees to the picture 4 1 5 1 1 MIN 2 MIDDLE 3 MAX Picture4 1 5 1 Press Prev or move the joys tick leftwards to return 4 1 6 Keyboard message display Enter the main menu Move the joystick to 3 to check the keyboard message LCD display sees to the picture 4 1 6 1 17 Version Number Version 1 00 KB 10 001 KeyBoard ID Protocol Factory Control Protocol Balldrate 960 Obps ommunication protocol Picture4 1 6 1 move the joys tick leftwards to return The keyboard mess age menu will display the keyboard parameter setting the keyboard model ID address the Keyboard protocol and the keyboard baud rate 4 2 Dome setting This paragraph mainly de scribes main functions of the operation ways of keyboard it need
6. 3 7 the dome main 11 COMMON TINS MANK REO CO Tm 11 3 8 1 Switch the domes mordere 11 3 0 2 Calman MERLOT ced SSSR aR 11 96 3 Conlifm allerPIOGFAM ria 11 ood Change Object Mono a 12 4 The Keyboard Menu 0 13 4 1 Keyboard Para meter Setting 13 1 ee Key GID mer 13 4 1 2 The keyboard baud rate 15 2 1 3 Joystick CallDEalloRis suina 16 4 1 4 Multi keyboard Connection state setting 17 4 1 5 Keyboard screen brightNess 17 4 1 6 Keyboard message display 17 2 DomeSelUtTg uou mae alii a aaa 18 4 2 1 Dome preset setting 18 4 22 TOME SCAM Sellia 20 4 2 9Pattern settingi ici helle 21 Tour Selling inni ea 22 1 FOLOCO SEUNG ein 23 Mode slot 23 4 3 2 Dome controlling iaia 23 423 0 DYR controlling MOJE vies 5 eR see a 24 keyboard Menia 24 SIR 21001219 6 RT RT SA 24 5 TRS485 BUS 24 5 2 Keyboard shortcut operation 28 6 Keyboard Menu Madek licia 30 7 Maintenance service terms 30 la Range Or
7. 4 1 2 1 The baud rate is divided into 2400bps 4800bps 9600bps and 19200 bps user can choose baud rate according to the application and then pres Enter to save The screen display 15 success it means the operation is success Then Press Prev or move the joys tick left war do to go back Must be used 9600 BPS when connecting with the matrix y and must b e used 9600 B PS or 1 9 200 bps when connecting b the keyboard online NOTIC 4 1 3 Joystick Calibration User enters into the Joystick calibration menu and calibrates the joys tick when it cannot be cont rolled The joy stick must to be nature state when you do it Enter the main menu LCD display Sees to the picture 4 1 1 1 Move the joystick to 1 to choose the key board setting LCD display Sees to the picture 4 1 1 3 Move the joystick to 3 to enter Joy stick Calibration LCD display sees to the picture 4 1 3 1 Joystick is free then Press Enter Picture 4 1 3 1 Press Enter then finish the operation The screen display sees to the picture 4 1 3 2 Success Picture 4 1 3 2 N The joystick must be nature state when joystick calibration NOTICE 16 4 1 4 Multi keyboard Connection state setting Enter into OSD menu LCD will display as Picture 4 1 1 1 shows Press 1 to set the keyboard LCD will display as Picture 4 1 1 2 shows Press 4 to set multi keyboard connection state setting After you
8. 485 X1 RS422 X 1 RJ 45 Communication frequency 2400 4800 9600 19200Bps Communication distances 1 2km RS485 and RS422 can achieve it e Operational environment Operating temperature 0 C 50 C 1 Relative humidity Less than 90 e Physical property L 218 180 55 mm Weight 630g Net Weight 2 Keyboard Connection 2 1 Keyboard Interface Instruction There is inter face on the back of the key boa rd which equipped with kinds of communication interfaces RS422 RS485 RJ 45 which can connect and control kinds of peripheral equipment 2 1 1 RS42 2 and RS485 interface RS422 and RS485 interface are on the Gbit ribbon cable connection of the keyboard RS485 A B can connect with the dome when the key board controls the dome directly RS485 A B can connect with DVR or other keyboard when the keyboard controls the dome by matrix RS 422 T T is s ending the signal RS422 R R is receiving the signal both of which can connect with matrix DVR and son Picture2 1 1 2 1 2 RJ45 Interface It is the standard net work interface which can be mainly used for connecting with the matrix for short distance the distance is less than 7 6m About the details Please see to 2 3 matrix connection 6Bit ribbon Cable RJ45 Power Supply Port Picture2 1 2 2 2 Matrix Connection The keyboard can control matrix of PELCO CM6700 CM6800 For example following that the keyboard connects with the
9. 9600 bps 4 19200 bps 1 Keyboard setup 2 Dome setup 3 Protocol select Aboutkeyboard calibrate 4 Exit menu Version 1 00 E PR KB ID 008 Joy is free then Protocol Factory Baudrate 2400 Press ENTER Dome setup Setdome preset 5 1 Set dome preset 1 Save preset Preset num 2 Set dome scan 2 Show preset lt D 3 Set dome pattern 3 Clear preset Press prev to back 4 Set tour e e The product will be maintained free for one year Setdomescan Set left limit Set right limit 1 Setleftlimit Press enter sure Press enter sure 2 Set right limit 3 Runscan Success Press prev to back Press prev to back Set dome pattern Set pattern Runpattern 1 Pattern num Press 1 to start 2 Set pattern Press Oto stop Success 3 Run pattern Press prev to back Set dome tour Insert preset Runtour 1 Tournum 1 Presetnum 2 Insert preset 2 Speed Success 3 Run tour 3 Dwell 7 Maintenance 6 1 Range of warranty CamiD 001 MoniD 001 Protocol Pelco P Protocol select _ _ Matrix Pelco matrix Baudrate 9600 1 Matrix 1 Pelco matrix 2 Dome Success 1 Factory 2 Pelco P Success 3 Pelco D 4 VIDO B02 30 e The product will be obtained the free maintenance service if the same malfunction appears again within three months e Malfunction of products caused by force majeure such as war earthquake lightning
10. PELCO CM 6700 matrix in order to introduce the connection between the keyboard and the matrix There are two kinds of keyboard connection inter face on the CM6700 matrix back plate one is local keyboard connection interfaceRJ45 LOCALKE YBOARD which can control the single keyboard within the distance of 7 6 m The other is the remote interface RS 422 REMOTE EYBOARD s which can connect with the keyboard RS422 interface the maximum distance is 1200m 2 2 1 RJ45 Local Connection Please insert one crystal end of RJ 45 connect ion line into the Rj45interface of the keyboard and insert the other one into the RJ45inter face LO CALKEYBOARD of CM6700matrix 1 RJ45 local connection the distance between the Keyboard and the matrix is less than 7 6m 2 RJ45 interface has 12VAC it not need other power f M NOTICE when the keyboard connect to CM6700 matrix Keyboard 1 Pin8 Pinl Power INPUT AC DC 9V 12V AC DC 9 12V NC 2 T 6 NC 3 energy 7 R 4 J NONPOLAR R Ga asl RJ45 RS422 Keyboard 2 05485 RS422 A UE gem s occum EE enum OUTPUTS f Keyboard Matrix T T R R T R T Picture2 2 1 2 2 2 RS422 remote connection RS422 connection line one end connects with RS4 22 interface REM OTE K EY BO ARD s of CM6700 back plate the other end co
11. Protocol setting Enter the menu as LCD shows picture 4 1 1 1 Press 3 to enter protocol setting as LCD shows picture 4 3 1 1 Matrix 2 Dome 3 DVR Picture 4 3 1 4 3 1 Pelco matrix mode Move the joystick to 1 to enter PELCO matrix mode As LCD shows picture 4 3 1 1 Move the joystick to choose protocol and back to the former menu 1 Pelco matrix Picture4 3 1 1 4 3 2 Dome controlling mode Move the joystick to 2 to enter dome directly con trolling mode as LCD shows picture 4 3 2 1 Choose corresponding protocol according to user s actual instance the system will back to the former menu automatically after deciding the protocol 23 1 Factory protocol 2 Pelco p protocol 3 Pelco d protocol 4 VIDO B02 Picture 4 3 2 1 4 3 3 DVR controlling mode Move the joystick 3 to enter DVR directly con trolling mode as LCD shows picture 4 3 2 1 Choose corresponding protocol according to user s actual in stance the system will back to the former menu automatically after deciding the protocol 1 Wonwoo 2 QH16CH DVR Picture 4 3 3 1 4 4 Exit to keyboard menu Enter the menu as LCD shows picture 4 2 1 1 Move the joystick 4 to exit the menu directly 5 Appendix 5 1 RS485 Bus Basic Knowledge Characteristic of RS48 5 Bus line According to RS485 standards RS485 Bus is of half duplex data transmission cables with characteristic impedance as 120Q The maximum lo
12. User Manual RS485 Surveillance Keyboard re ce amp Directory EDT LIII UE C 1 i INO UGS tafe era 1 1 2 Function and Characteristle lella 1 TS Datasheet alata ETE ls 1 2 Keyboard CONNECUON siti dali 3 2 A eyboard ntertace Instr cllOEb 3 2 1 1 R942 2 and RS485 interface re serena 3 2 52 NISI ACS pcc P 3 2 2 CONNEC UOM ila SA ORNATA 4 22 445 Connection eA 4 2 2 2 422 ati 5 2 3 Connect with the Dome Directly sess 5 2 4 The Connection of the Keyboard in the System 6 Keyboard Operation Manual n anal 7 3 1 Electrify to keyboard e arance 8 Oe GD 8 23 JOVStick G0Ntro S ING domestici 9 CiiahiGS lab iii 9 9 9 Dome Jens CONO sioe lai 9 3 6 Dome licei axa TNA 10 SO EFOSC fosa 10 ON M ur NIMM ITE MI 10 O acis ERN OD TEE ETE EET 10 SNR TOUR en E 10
13. ad capacity is 32 unit loads including main controller and controller equipment Trans mission distance of RS 485 Bus line When user selects the 0 56mm 24AWG twisted pair as data transmission cable the 24 maximum theoretical transmitting distances are as follows according to different baud rate If user selects thinner cables or installs the dome in an environment with strong electromagnetic interference or connects lots of equipment to the RS 485 Bus the maximum transmitting distance will be decreased To increase the maxim um transmitting distance do the contrary Baud Rate Maximum Distance 2400 bps 1800m 4800 bps 1200m 9600bps 800m Connection and terminal resistance The RS485 standards require a daisy chain connection between the equipment There must be termination resistance wit h 1200 at both ends of the connection refer to picture 4 1 1 Please refer to picture4 1 2 for simple connection And D should not exceed 7m 2H 3H 4 32H Picture4 1 1 25 Picture 4 1 2 Problems in practical use User adopts a star configuration in practical connection The termination resistors must be connected to the two equipments which are farthest away from each other such as equipment 1 and 15 refer to picture 4 1 3 This connection way not accord with the requirements of RS485 standards it is easy to bring signal reflections lower anti interference performance when the cable distance of t
14. control the dome directly at this time the keys in lens controlling area also can control f the dome lens the operation of the joy tick and the key is invalid for the NOTICE dome under general menu mode Picture 4 Preset num 1 255 Picture2 1 5 19 Input corresponding preset number press Enter to call preset LCD will show Success tilt the joys tick left or press Prev to back to the former menu Move the joystick to 3 to enter the clearing preset menu As LCD shows Picture 4 2 1 6 Preset num 1 255 Picture 4 2 1 6 Input the preset number that you want to clear press Enter to clear preset LCD will show Success and back to the former menu 4 2 2 Dome scan setting Enter the menu as LCD shows picture 4 1 1 1 Move the joystick to 2 to enter the dome setting menu as LCD shows picture4 2 1 1 Move the joystick to s 2 again to enter the dome scan setting menu as LCD shows picture4 2 2 1 1 Set left limit 2 Set right limit 3 Run scan Picture 4 2 2 1 Dome scan setting includes setting dome left limit right limit and running scan Choosing 1 to set dome left limit as LCD shows picture 4 2 2 2 Press enter sure Press prev to back Picture 4 2 2 2 After entering the setting dome limit menu to move the dome in an appropriate position 20 then press Enter to save LCD will show Success and back to the former menu Choosing the
15. ctly at this time the keys in lens controlling area also can control 7 the dome lens the operation of the joystick and the key is invalid for the NOTICE dome under general menu mode 4 2 4 Tour setting Move the joystick to 2 to enter dome setting menu as LCD shows picture 4 2 1 1 Move the joystick to 4 to enter the menu of tour as LCD shows picture4 2 4 1 1 Tour num _ 2 Insert preset 3 Run tour Picture 4 2 4 1 After entering the menu the system requires in putting tour that you will set in the first item the input range is 1 6 press Enter to confirm the cursor will auto jump to the second row to start tour setting if user has finished to set tour already you can jump over the second item to run tour directly LCD will show Success and back to the former menu it means the operation is successful Choosing the second item as picture 4 2 4 2 shows to input presets that you need to insert in at our inputting preset speed in the second item In put range 1 127 inputting pres et par k time in the third item input range 1 255 press Enter to confirm LCD will show Success and back to the former menu it means the operation of adding preset is successful 1 Preset num __ 2 speed 3 dwell Picture 4 2 4 2 22 Press 3 to run tour Is valid to insert the presets in tour underVIDO B02 im Protocol but it is invalid under other protocols NOTICE 4 3
16. e N Cam N means numeric key Do not explain it again input the dome ID Press Cam to change object dome 3 5 Dome lens control e Zoom control Press TELE lens zoom tale the multiple of lens increase leave to stop Press WIDE lens zoom wide the multiple of lens reduction leave to stop e Focus control Press FAR manually far focus to make the far object more legible leave to stop Press NEAR manually near focus to make the near object more legible leave to stop As usually the camera is in the status of auto focus user operates manual focus and run other operations by the two keys and the camera will automatically resume to auto focus e Iris control Press OPEN manual Iris increase Iris is max the screen will show white leave to stop Press CLOSE manual Iris reduction Iris is the screen will show black leave to stop 3 6 Dome function operation 3 6 1 Preset e Set preset SET N Preset e Call preset N Preset N means preset number 3 6 2 Scan e Set left limit SET 1 Scan e Set right limit SE T 2 Scan e Run scan 1 Scan User should enter into menu setup if change the speed of scan 3 6 3 Pattern e Set pattern path SET N PATTERN Path SET 0 PATTE RN Press SET input pattern 1 4 Press PATTERN enter tour setup the dome records a series of motions when end press SET
17. he equipment is far away from each other The reliability of control signals is decreased It cannot control the dome or sometimes can or sometimes cannot or continuous operate by itself The factory will recommend the 5485 distributor The distributor can transfer the star configuration connection to the mode of connection accordance with the RS 485 standards The new connection achieves reliable data transmission and avoids the problem Refer to picture 4 1 4 26 6 Main Controllor Picture4 1 3 Rs485 Distributor Picture 4 1 4 2 5 2 Keyboard shortcut operation manual Working Mods Sto Operation object Function Input Dome ID pre Cam to select Cam Press Tele increase the multiple of Tele High speed dome lens I Press Wide reduce the multiple of Wide High speed dome lens Press Near near focus Set Adjust the image to object position High speed dome object dome press Sett to input Preset Direct N High speed dome Number then press Preset to set Control Mode and PELCO Matrix Mode Preset N Preset SET 1 Scan Set N Patter High speed dome High speed dome High speed dome High speed dome High speed dome High speed dome 28 preset Input preset Number press Preset to call the preset Adjust the image to object position press Set to input 1 then press scan to set scan left limit Adj
18. is required to have a main keyboard the main keyboard ID set as 1 the Baud rate of keyboard is set as 9600bps Sees to the picture 2 4 2 Dome Dome2 Picture2 4 1 1 A line of RS485 may control up to 32 main controlling and under controlling equipments so a keyboard which controls the dome directly may connect up to 31 domes 2 The system may connect up to 4 keyboards at the same time and the four keyboards ID are different 4 4 C Dome1 Dome2 Dome3 ES p LJ Keyboard 4 _ _ _ _ Dome5 Dome6 Dome7 RIE Picture 2 4 2 3 Keyboard Operation Manual LCD Lens controling X 4 bd bd bd Function f TA oystic Cay ui ZOME y Picture 3 1 1 This paragraph describes mainly the operation ways of keyboard needs to especially explain that different systematic platform has not the same operations and different systematic platform may have some particular requirements and operations plea se operate it to combine with the operation manual of dome and matrix 3 1 Electrify to keyboard When electrify to keyboard the keyboard will auto test the baud rate protocol and object dome and object monitor will auto set as 1 and these information will display in the LCD N When the keyboard is initializing the joystick Must to return 0 can not to pull or rotate the joystick NOTICE 3 2 LCD
19. nnects with RS4 22 interface of the keyboard the keyboard interface RS 422 R R corresponds with matrix interface RS 422 T the keyboard inter face RS 422 T T corresponds with matrix interface 5422 R RS422 remote connection the maximum distance X between the keyboard and the Matrixes 1200m OTICE N 2 3 Connect with the Dome Directly You can connect with the dome by RS485 inter face when the keyboard controls the dome directly The RS485 interface of t he dome is on the switch board of pendent hanger of the upper cover of the dome You can find the 4 Pin control power socket and find the corresponding RS485 A B interface according to the above mark when you turn the metal button inside the hanger and open the switch board There are different connection ways according to the domes which produce by the different 5 manufacturers About connection with the dome please see to the dome installation manual AC24RS485 A B HER RS485 RS422 1 A B T T R R L Dome Power AC DC 9V 12V Picture 2 3 1 2 4 The Connection of the Keyboard in the System The keyboard controls the matrix and then controls the domes indirectly by the matrix sees to the picture2 4 1 When unconnected with the matrix the keyboard controls the dome directly Keyboard and camera parallel connect to RS485 Bus and each keyboard can control each dome This way
20. ogram ENTER after the matrix programmed press ENTER means confirm after program as for the detail program please refer to the matrix operation manual 11 3 8 4 Change object monitor N MON Input the monitor ID then press MON the image and the menu of the dome that you control led by keyboard will display in the object monitor 12 4 The Keyboard Menu Controlling The keyboard me nu con trolling Press SET 2 seconds Got the main menu the LCD display is following See the picture 4 1 1 all menu setup should call main menu Press numerical key or move the joystick up and down to the option which you need and then turn it right after entering the main menu which can enter the relevant menu setting 1 Keyboard setup 2 Dome setup 3 Protocol select 4 Exit menu Picture 4 1 1 Saving Setting Choose relevant numerical keys in according to the menu hint then can enter relevant function set ting Press Enter to reserve LCD will display success after finishing the setting success fully Return to Previous menu Press Pre v or move the joy stick left ward then return the previous menu 4 1 Keyboard Para meter Set ting 4 1 1 Set keyboard ID 1 Enter main menu LCD display See to picture 4 1 1 1 1 Keyboard set up 2 Dome setup 3 Protocol select 4 Exit menu Picture 4 1 1 1 13 2 Move the joystick to 1 then choose keyboard setting LCD display see
21. s to especially explain that different systematic platform has not the same operations and different systematic platform may have some particular requirements and operations please operate it to combine with the operation manual of dome and matrix 4 2 1 Dome preset setting Enter the main menu as LCD shows Picture4 1 1 1 Move the joystick to 2 to enter dome setting menu as LCD shows Picture 4 2 1 1 Move joy stick up and down to separately set dome preset scan pattern and tour 1 Set dome preset 2 Set dome scan 3 Set dome pattern 4 Set dome tour Picture 4 2 1 1 Move the joystick to 1 to enter dome preset setting as LCD shows Piture4 2 1 2 1 Save preset 2 Show preset 3 Clear preset 18 Picture 4 2 1 2 The first item is setting dome preset the second item is calling dome preset the third item is clearing dome preset Move the joystick to 1 to enter preset setting this item requires inputting the preset number that you will save as LCD shows Picture 4 2 1 3 Preset num 1 255 Press prev to back Picture 4 2 1 3 After entering the setting dome preset menu the joystick will control the dome directly in putting the corresponding preset number then press Enter save LCD will show Success As picture 4 2 1 4 shows Success Pitcture4 2 1 4 Press Prev to back to the former menu A After entering the setting dome preset menu the joystick will
22. strike and soon abuse non standard operation change of construction non normal wear or acc dent are non free of warranty e Please prevent from the damage which is caused by heavy pressure the fierce vibration and soaks in the process of transportation and storage which does not belong to the free maintenance scope e Please adopt the way of fission package or original package to transport because the product damage does not belong to the free maintenance scope if you use the whole packing Way not the original packing way e The maintenance services will not be free when the pan tilt module is disassembled serviced by the user voluntarily e Our company implements the lifetime payable service if the product in malfunction has surpassed the warranty period e To the products with defect If it s in the period of warranty please fill in the form of warranty information correctly describe the trouble in details and provide the trouble in details and provide original sales invoice or its copy e For the damage and loss which was caused by the user s specifically application factory won t bear any risk and responsibility The factory compensation made by breach of faith negligence or tortuous won t exceed the amount of the products The factory won t bear any responsibility for the special unexpected and continue damage caused by any other reasons e Our company has the final right of explanation for the above terms 2 Warran
23. to the picture 4 1 1 2 1 Set KB Parameter 1 Screen Light 2 About keyboard Picture 4 1 1 2 3 Move the joystick to 1 to choose keyboard Specification LCD display sees to the picture 4 1 1 3 1 Set KB ID 2 Set ball rate 3 Joy_calibrate Picture4 1 1 3 4 Move the joystick to 1 to choose keyboard ID setting LCD display Sees to the picture 4 1 1 4 Input KB ID 1 64 Picture 4 1 1 4 Press the relative numeric al key 1 64 Press enter Enter to confirm The screen display See to picture 4 1 1 5 which means operating success fully Success Picture 4 1 1 5 14 The screen will show Error if input the numerical key which are excess the ID scope 1 6 4 Sees to picture 4 1 1 6 Picture4 1 1 6 5 Press PREV ormove the joy stick left wards then go back gradually The factory default ID of the keyboard is 1 The ID Number must be 1 if the single keyboard works 4 4 It can connect up to 4 keyboards when working online but make sure there is only a keyboard ID set as 1 otherwise all the online keyboards cannot work normally NOTICE 4 1 2 The keyboard baud rate setting Enter menu LCD display sees to the picture4 1 1 1 Move the joystick to 1 to set the keyboard LCD display sees to the picture 4 1 1 2 Move the joystick to 2 to set the keyboard baud rate LCD display Sees to the picture 4 1 2 1 2400 bps 4800 bps 9600 bps 19200 bps Picture
24. ty terms e lf the products are within the warranty time the buyer should fill in the warranty card and send back together with the products 3 Shipping e f the product needs repaired you can return it to the manufacturer through the supplier or directly If you choose the later please contact us in order to speed up the process And our company only undertake the one way freight from manufacturer to customer after maintenance 31 Ep Farr did e iii i ne rieti ir citt At T ace ee act to change without notice Design and specifications are sub DISTRIBUTED BY
25. ust the image to object position press Sett to input 2 then press scan to set scan right limit Input 1 press Scan to run scan Press Set to input pattern number presses Pattern to record pattern path Pres Set input 0 then press 0 Pattern to save pattern Patter N Input pattern number 1 4 press High speed dome Patter Pat tern to run pattern N Input tour number press Tour or Tour High speed dome Tour 91 5 Preset directly press Tour to run cruise High speed dome Input 95 to call main menu of dome Shift Press Shift and Set to call main Matrix Set menu of matrix Switch to previous dome Press Prev to jump the previous dome press Prev Matrix Prev to hold it for 2s continuously switch the sixteen domes of connection matrix forwards Switch to next dome Press Next PELCO Matrix to jump the next dome press Next Next Matrix to hold it for 2s continuously switch the sixteen domes of connection matrix backwards Stop Stop to switch After program press Enter to Enter Matrix confirm Input monitor Number press Cam Monitor to select object monitor 29 6 Keyboard Menu Index Keyboard setup Set KB Parameter SetKBID Setbaudrate 1 2400 bps 2 4800 bps 1 Set KB Parameter 1 Set KB ID Input KB ID 2 About keyboard gt 2 Setbaudrate 3 Joy calibrate 4 Mult keyboard state 3
Download Pdf Manuals
Related Search