IR Analog Intelligent Speed Dome User`s Manual
Contents
1. Housing Camera Driver Bearing Connection 5 E E Cable Motor C O O If possible Power Q O If possible Bracket 5 5 If possible Accessories Note O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes 27 Note This manual is for reference only Slight difference may be found in the user interface All the designs and software here are subject to change without prior written notice All trademarks and registered trademarks mentioned are the properties of their respective owners If there is any uncertainty or contro2. eon dO RR REED RU ER ERREUR A 21 3 5 2 PTZ Movements not smooth timere eei mi eee eter t teres 21 4 CABLE CONNECTION em 22 4 1 System LAY OU CREE T 22 SYSTEMMCOMMECUON e 22 4 1 2 Alarm Connection IURE RR RUNE HIERRO ERE EUER Ea 23 dko Keyboard Gonnectlon nro ni mro ORE OPI RFID REIS 24 BFA 25 5 1 Daily Maintenance 25 5 2 Problems and Solutions eee esent eene 25 6 APPENDIX I LIGHTENING PROTECTION AND SURGE PROTECTION 26 7 APPENDIX 2 TOXIC OR HAZARDOUS MATERIALS OR ELEMENTS 27 ii Welcome Thank you for purchasing our product This user s manual is designed to be a reference tool for the operation of your system Here you can find information about this speed dome features and functions as well as a detailed menu tree Please keep it well for future reference Before installation and operation please read the following safeguards and warnings carefully iii Important Safeguards and Warnings Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC or 24V AC in the IEC60950 1 We
3. Alarm in 1 7 GND Note e Seven alarm input channels It is to receive relay signal from the external alarm source You can go to dome menu to activate specified preset or scan When the activation mode is NO normal open dome alarms when there is low voltage High voltage will not activate the alarm When the activation mode is NC normal close dome alarms when there is high voltage Low voltage will not activate the alarm Dome alarm input message is ground mode Dome alarm input signal are two modes normal open and normal close Alarm input ground end 4 1 System Layout 4 1 1 System Connection 4 1 1 1 BUS connection Please refer to Figure 4 1 for system connection information 22 AC 24V Output Input AC 220V Power Adapter RS 485 Terminal resistance on Figure 4 1 Note Please use shielded twisted pair The shielded layer shall connect to GND firmly otherwise it may affect communication or video work 4 1 1 2 Star Connection Please refer to Figure 4 2 for alarm connection information Figure 4 2 4 1 2 Alarm Connection Please refer to Figure 4 3 for alarm connection information 23 thers Alarm Controller Figure 4 3 4 1 3 Keyboard Connection This series dome supports keyboard operation You can use keyboard to control the dome and PTZ The display and control can work simultaneously One keyboard can control maximum 255 speed domes Please refer t
4. CONTROL It is to set temperature control mode It includes three modes auto normal open normal close Please use the left right button on the keyboard or in the speed dome terminal menu to set OPEN TEMPERATUREP This function is on when the heater control mode is auto It is for you to set temperature to enable the heater CLOSE TEMPERATURE This function is on when the heater control mode is auto It is for you to set temperature to disable the heater BACK Go back to the previous menu EXIT Log out the system menu 3 4 5 Alarm Setup ALARM NO ACTION PARAMETER CONTACT RELAY OUT RESET DELAY SAVE BACK Move the cursor to highlight ALARM SETTING button and then click confirm button 20 ALARM NO Here is to set alarm input Alarm input value ranges from 1 to 7 Please use the left right button on the keyboard or in the speed dome terminal menu to set ACTION Action on alarm function It includes NONE PRESET AUTO SCAN TOUR functions Please use the left right button on the keyboard or in the speed dome terminal menu to set PARAMETER it is to set corresponding alarm operation such as scan preset tour Please use the left right button to set CONTACT You can set system activation operation once alarm occurred There are two alarm signal mode normal open N O and normal closed N C Please use the left right button on the keyboard or in the speed dome terminal menu to set RELAY OUT Here is to set
5. assume liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair Transportation Security No heavy stress violent vibration or water splash are allowed during transportation storage and installation Please use the original packing material or the material of the same quality when you ship it back to the manufacturer Installation Do not apply power to the product before completing installation Please install the proper power cut off device during the installation connection Do not put object on the product Environment This series product should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the device Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Thunder proof device is recommended to be adopted to better prevent thunder The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera Daily Maintenance Current series product has no power button Please unplug all corresponding power cables
6. before your begin installation or daily maintenance work Please keep the dustproof cap back to protect the CCD or CMOS part if the device does not work for a long time Do not touch CCD CMOS component You can use the blower to clean the dust on the surface of the device You can use the dry cloth with some alcohol or mild detergent to clear if necessary Do not use the volatility solvent such as the benzene or thinner or detergent with strong abradibility It may result in lens damage or it may adversely affect the device performance iv If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device 6 About Accessories Always use all the accessories recommended by manufacturer Before installation please open the package and check that all the components are included in the package Contact you local retailer ASAP if something is missing in your package 1 Features and Functions 1 1 General Introduction The series IR analog intelligent speed dome is a product of general high level of integration and intelligence This is a digital and intelligent product of vivid video It can automatically enable IR light function under the low illumination environments and near far IR light intelligent control function The installation is convenient Comparing with the traditional products this series IR analog intelligent speed d
7. in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 3 4 3 2 Exposure Setting AE MODE AGC GAIN LIMIT GAIN SETTING HIGH GAIN SHUTTER SLOW SHUTTER LIMIT IRIS SETTING NOISE REDUCTION EXPOSURE COMP 3D NOISE REDUCTION SLOW AE BLC SLOW SHUTTER WDR NEXT PAGE AE RECOVERY BACK BACK AE MODE Here you can set the camera exposure mode It includes auto manual AV iris priority TV shutter priority Please use the left right button on the keyboard or in the speed dome terminal menu to set lt Auto It is for you to set the exposure compensation backlight compensation BLC slow shutter wide dynamic region WDR lt Manual It is for you to set the gain setting shutter iris setting wide dynamic region WDR lt Iris Priority AV It is for you to set the exposure setting iris setting wide dynamic region WDR lt Shutter Priority TV It is for you to set the shutter setting exposure compensation wide dynamic region WDR GAIN SETTING It is to set camera gain Please use the left right button on the keyboard or in the speed dome terminal menu to set 10 SHUTTER It is to set camera shutter Please use the left right button on the keyboard or in the speed dome terminal menu to set IRIS SETTING It is to set camera iris Please use the left right button on the keyboard or in the speed dome terminal menu to set EXPOSURE COM It is to
8. options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set FREEZE FUNCTION This function allows the system from one preset to another preset without showing the video during the PTZ movement There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set IMAGE STABILIZATION This function can guarantee video stability once there is any vibration on the speed dome installation environments CAMERA FACTORY DEFAULT Move the cursor to current item and then click confirm button to restore factory default setup CAMERE RESTART Move the cursor to current item and then click confirm button to reboot the camera BACK Go back to previous menu EXIT Log out system menu 3 4 3 1 White Balance Setup WBMODE AUTO R GAIN 210 B GAIN 150 BACK EXIT Move the cursor to WHITE BALANCE MODE and then click confirm button you can go to the submenu WHITE BALANCE MODE Set white balance adjustment mode There are two modes auto manual Please use the left right button on the keyboard or in the speed dome terminal menu to set R GAIN Before you set R GAIN option please note the mode is manual Please use the left right button on the keyboard or in the speed dome terminal menu to set B GAIN Before you set B GAIN option please note the mode is manual Please use the left right button on the keyboard or
9. or in the speed dome terminal menu to set POSITION Display the angel between the benchmark and then current location Please use the left right button on the keyboard or in the speed dome terminal menu to set ZOOM DISP Display speed dome zoom speed value or not Please use the left right button on the keyboard or in the speed dome terminal menu to set INSIDE TEMPERATURE Display dome internal temperature or not There are three options F Off Please use the left right button on the keyboard or in the speed dome terminal menu to set TITLE DISPLAY Here you can set to display speed dome position information and etc You can use the speed dome control terminal to set the detailed title information Please use the left right button to set BACK Go back to the previous menu EXIT Log out system menu 3 4 3 Camera Setting WB SETTING DIGITAL ZOOM EXPOSURE SETTING DIGITAL ZOOM LIMIT DAY NIGHT SETTING PICTURE FLIP FOCUS SETTING FREEZE _ FUNC ZOOM SPEED IMAGE STABILIZATION APERTURE 9 CAMERA FACTORY DEFAUTL APERTURE RESTRAIN CAMERA RESTART NEXT PAGE BACK BACK Move the cursor to CAMERA SETTING and then click confirm button you can go to the submenu WHITE BALANCE SETUP It is to set camera white balance mode Move the cursor to current option and then click confirm button you can go to the third menu EXPOSURE SETTING It is to set camera exposure mode gain and etc Move the cursor t
10. relay alarm mode and reset time There are several options off 1 55S 2 58 1 amp 2 58 lt 1 55 1 means the first relay output 5S means the relay will reset automatically in five seconds after alarm occurs lt 1 amp 258 1 amp 2 means the first relay and the second relay work at the same time RESET DELAY Here is for you to set alarm reset time Please use the left right button on the keyboard or in the speed dome terminal menu to set 3 seconds 10 seconds 30 seconds 60 seconds 120seconds The dome will go back to previous setup after alarm acknowledgement SAVE Move the cursor to SAVE and then click confirm button to save current setup BACK Go back to previous menu EXIT Log out system menu 3 4 6 IR Light Setting IR SENSITIVITY 04 IRLIGHT CTRL ZOOM PRI NEAR LIGHT 50 FAR LIGHT IRLIGHT COMP BACK Move the cursor to highlight IR LIGHT SETTING button and then click confirm button IR SENSITIVITY Here you can enable the IR light sensitivity function IR LIGHT CTRL There are three options Zoom rate has the higher priority and manual Please use the left right button to set NEAR LIGHT It is the medium and near light brightness This function is valid in MANUAL mode FAR LIGHT It is the far light brightness This function is valid in MANUAL mode IR LIGHT COMPENSATION It is the whole compensation level of the IR light This function is valid when the zoom rate has the higher priority BACK Go back
11. right button on the keyboard or in the speed dome terminal menu to set BACK Go back to previous menu EXIT Log out system menu 3 4 4 Function Setting PRESET AUTO PAN AUTO SCAN AUTO TOUR AUTO PATTERN IDLE MOTION TIME TASK NEXT PAGE BACK 12 Please go back to main menu and move the cursor to FUNCTION SETTING click confirm button You can see the above interface PRESET It is to set preset Move the cursor to PRESET and then click confirm button to go to the third submenu AUTO PAN It is to set pan Move the cursor to AUTO PAN and then click confirm button to go to the third submenu AUTO SCAN It is to set scan number speed and etc Move the cursor to AUTO SCAN and then click confirm button to go to the third submenu AUTO TOUR It is to set tour number tour operation and etc Move the cursor to AUTO TOUR and then click confirm button to go to the third submenu AUTO PATTERN It is to set pattern number and etc Move the cursor to AUTO PATTERN and then click confirm button to go to the third submenu IDLE MOTION It is to set idle operation idle time and etc Move the cursor to IDLE MOTION and then click confirm button to go to the third submenu TIME TASK It is to set system schedule operation Move the cursor to TIME TASK and then click confirm button to go to the third submenu NEXT PAGE It includes PRIVACY MASK PTZ SPEED SET ZERO POWER UP and etc Move the cursor to the item and then click the c
12. C001 OFF SC001 OFF SC001 OFF SC001 OFF NEXT PAGE PRIVACY MASK HEATER CONTROL PTZ SPEED i SET ZERO PTZ CORRECTION OFF POWER UP MENU PASSWORD BACK EXIT MENU IDLE PTZ AUTO STOP 155 NEXT PAGE SAVE BACK EXIT Move the cursor to the NEXT PAGE and then click OK button you can go to the third menu to set speed dome PTZ speed initialization position power up operation and etc PRIVACY MASK Here you can set the privacy mask number and etc It includes the third menu Please move the cursor to the current item and then click the confirm button to go to the next interface PTZ SPEED It is to set PTZ speed Please use the left right button to set SET ZERO Please move the PTZ to the horizontal coordinates click OK button to confirm POWER UP It is to set the PTZ action when the speed dome boots up Click the confirm button to go to the next interface to set MENU PASSWORD It is to set menu password Move the cursor to MENU PASSWORD and then click confirm button to go to the next submenu to set MENU IDLE If current setup is ON once you open the menu and leave it idle for specified period the menu may automatically disappear If current setup is OFF the menu is always there and will not disappear Please use the left right button to set PTZ AUTO STOP The speed dome will stop all the PTZ operations when there is no command for the specified time It includes various setups Please use the left right button to set NEX
13. FF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF OFF 7 ON ON ON OFF OFF OFF OFF OFF 8 OFF OFF OFF ON OFF OFF OFF OFF 254 OFF ON ON ON ON ON ON ON 255 ON ON ON ON ON ON ON ON 3 Menu 3 1 Screen Menu Index SYSTEM SETTING DISPLAY SETTING CAMERA SETTING FUNCTION SETTING ALARM SETTING IR LIGHT SETTING INITIALIZATION INFORMATION ADDR INFORMATION SETTING GUAGE English FACTORY DEFAULT RESTART BACK EXIT PRESET AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP TITILE PACK ACK EXIT WB SETTING EXPOSURE SETTING DAY NIGHT SETTING FOCUS SETUP ZOOM SPEED APERTURE APERTURE CNT NEXT PAGE BACK 8 9 PRESET AUTO PAN AUTO SCAN AUTO TOUR AUTO PATTERN IDLE MOTION TIME TASK NEXT PAGE BACK EXIT ALARM NO ACTION PARAMETER CONTACT RELAY OUT RESET DELAY SAVE BACK EXIT IR SENSITIVITY IRLIGHT CTRL NEAR LIGHT FAR LIGHT IRLIGHT COMP BACK EXIT The above diagram illustrates the overall structure of the speed dome setup menu Note ERR means current setup is invalid Please restore factory default setup Please make sure all the cable connections are right 3 2 Self diagnosis System Information ADDR 001 H BR 9600 PARITY None VERSION V1 00 0 RHNKDX DIAGNOSIS END After installation please connect speed dome to power The system goes on a self diagnosis and then it pops up the above interface to show the
14. IR Analog Intelligent Speed Dome User s Manual Version 1 0 0 Table of Contents T1 FEATURES AND FUNCTIONS ax aun idu x ui ak n UR id x Luka Ra an Eus 1 1 General Introduction ERR RR 1 2 Feat les es Pea ep ase Doo sss eH Gore O ec ques ae eo ap bes Ua EO e DEERE 1 2 1 On Screen Meu eerte eise e e te oi edidit aedes 1 2 2 Proportional Pan Tilt 2 re eret ete rete peer ee iere 1 2 9 Onescreen TIDS aient in uet uet en HR 12 44 Preset Setup and Call 55 35m ames ae amu annm 125 AUtO SCAN fees ERU ERE I ENTER E EUR UNS EA E EEE Ee INIRE URN He XE cv P E 1 267 sAUTOM OUI t oet ere t AS aee ar eta Ath A Ee SR 1 2 1 Auto P ttern ose eemladea ence ibidem 12 0 Privacy MASKING ite eet ege ERU 1 29 Action on Alar iori et i iei et de aes erin eet ete ee ee feed 1 2 10 eGU ERU ER RECEN 1 2 11 E 1 2 12 Day Night Mode B W amp Color Mode sse enne 1 2 13 Auto EOGQUS zen ae i eR Ep re URP REED 1 2 14 Backlight Compensatlon art reet eR rne E Ere dier rene ia ea 1 2 15 Pan Tilt and Zoom eee de ie ate D aee 1 2 16 9D Intelligent Location e RE RR e P RU n RU ROO REP 1 2 17 Idle Status oer eec eee em i
15. T PAGE It includes heater setting self diagnosis and etc HEATER SETTING It is to set heater Move the cursor to the item and then click the confirm button to set SELF DIAGNOSIS It is to set system self diagnosis correction Please use the left right button on the keyboard or in the speed dome terminal menu to set on off Please note you need to restart speed dome to activate current setup Privacy Mask 18 Ms the cursor to PRIVACY MASK and click confirm button system goes to privacy mask setup interface PRIVACY RESIZE PRIVACY MASKING SAVE SETTING BACK Note For security reasons please set privacy zone a little bit larger than the privacy object size Each time after modifications you need to move the cursor to SAVE button and then click confirm button to get all setup activated Otherwise privacy zone may not move correspondingly with the object Please enter privacy mask menu Move the cursor to PRIVACY NO please use left right key to set different privacy zones For example shift to 1 section and then move the cursor to PRIVACY MASKING Secondly click OK button to go to the setup interface Now there is a privacy zone in the screen centre Operate PTZ to move the camera screen so that the centre of the object you want to shield is overlaying with the centre of the screen Thirdly move the cursor to RESIZE and then click left and right key to adjust privacy zone direction and size Move the cur
16. button to set You can set for one day or you can set for the whole week START TIME Here you can set the task begin time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detailed value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit start time setup and then move the cursor to the SAVE button to save current setup END TIME Here you can set the task end time Move the cursor to current item and then click confirm button to set the time Please use the up down button to set the detail value and then use left right button to go to the next setup item After you completed the setup please click confirm button to exit end time setup and then move the cursor to the SAVE button to save current setup TASK ACTION The option here includes none tour scan preset patter and etc Please use left right button to set OPERATION NO It is the corresponding serial number of the schedule task The number here may vary due to different action types BACK Go back to the previous menu EXIT Log out the system menu Task Information Move the cursor to the TASK INFORMATION and then click the confirm button to go to the following interface Here you can see the corresponding task information Click the confirm button again you can exit current interface 17 ACTION SC001 OFF SC001 OFF SC001 OFF S
17. button to set the tour Please use up down button to set preset number dwell time and speed Use the left right button to go to the next tour Click confirm button you can exit the setup After you completed the setup move the cursor to back button to go to the previous interface DELETE TOUR Here is to delete a tour Input tour number in TOUR NO and then move the cursor to DELETE TOUR click confirm button to delete CALL Here is to activate tour Input tour number in tour NO and highlight CALL click confirm button to activate tour STOP Here is to terminate touring BACK Go back to previous menu EXIT Log out system menu 3 4 4 5 Auto Pattern PATTERN NO PROGRAM START PROGRAM STOP CALL STOP BACK Pattern function can memory PTZ operation and camera focus zoom in and zoom out From the start position dome begins auto movement repeatedly This series IP dome supports maximum 5 patterns and one pattern can max support 400 commands Move the cursor to PATTERN and click confirm button PATTERN NO Here is to set pattern number Please click left right key to configure e PROGRAM START Here is to memorize pattern starting point An icon OK pops up in screen to prompt you system begins memory pattern PROGRAM STOP Here is to set pattern stop point After all the movement move the cursor to PROGRAM STOP and then click confirm button Now you have set one pattern System pops up an icon OK to promp
18. confirm button to go to the third submenu SET NORTH Set dome benchmark direction so that you can know the angel between the benchmark and then current location Please move the cursor to the option and then click confirm button until you see O K Now you have set north direction LANGUAGE The dome menu language There are several languages for you to select Please use the left right button on the keyboard or in the speed dome terminal menu to set FACTORY DEFAULT Restore dome factory default setup Please move the cursor to the option and then click confirm button until you see O K Now you can see the IP dome begin rebooting to restore factory default setup RESTART Reboot the speed dome BACK Go back to the previous menu EXIT Log out system menu 3 4 1 1 Initialization information 001 H 9600 PARITY NONE VERSION V1 00 0 RHNKDX BACK EXIT Move the cursor to INITIALIZATION INFORMATION and then click confirm button you can see the above interface Here you can view dome basic information 3 4 1 2 Address Information ADDR TYPE ADDR HARD ADDR SOFT BACK Move the cursor to SITE INFORMATION and then click confirm button ADDR There are two options soft and hard Please use the left right button on the keyboard or in the speed dome terminal menu to set ADDR HARD It is an address you set in the dial switch You can not modify it through software ADDR SOFT You can set address via
19. der the land to implement cable layout and connects one point to the earth Open floor cable layout is forbidden e In area of strong thunderstorm hit or near high sensitive voltage such as near high voltage transformer substation you need to install additional high power thunder protection device or lightning rod The thunder protection and earth of the outdoor device and cable shall be considered in the building whole thunder protection and conform to your local national or industry standard System shall adopt equal potential wiring The earth device shall meet anti jamming and at the same time conforms to your local electrical safety code The earth device shall not short circuit to N neutral line of high voltage power grid or mixed with other wires When connect the system to the earth alone the earth resistance shall not be more than 40 and earth cable cross sectional area shall below 25 mm2 See Figure 6 1 Video Lighting Rod Communication Liqhting Rod Power op Lighting Rod The speed dome shall be installed within the 45 angel of the lighting rod Earth cable resistance shall be less than 40 Steel tube shield Figure 6 1 26 7 Appendix 2 Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Sheet Metal Plastic Parts
20. e object in the dark light to achieve a clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set o WDR It is an abbreviation for wide dynamic region Please make sure your camera supports current function This function can adjust the video brightness when the contrast between the strong light and the dark light is too high Move the cursor to current item and then click the OK button to go to the fourth level menu Please use the left right button on the keyboard or in the speed dome terminal menu to set o RECOVERY Manually click the and button on the PTZ interface system cam resume previous exposure value after specified time The exposure value does not resume if this function is off BACK Go back to previous menu EXIT Log out system menu 3 4 3 3 Day Night Setting Move the cursor to DAY NIGHT SETTING and then click confirm button you can go to the submenu DAY NIGHT AUTO DAY TIME 07H 00M NIGHT TIME 19H 00M THRESHOLD 4 SAVE BACK EXIT 11 DAY NIGHT It is to set camera day night switch mode Please use the left right button on the keyboard or in the speed dome terminal menu to set DAY TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and
21. e PTZ operation when the speed dome boots up The option includes NONE AUTO SCAN PRESET PATTERN TOUR and etc Please use the left right button to set PARAMTER Here you can set the serial number of the corresponding operation such as the scan preset pattern tour Please use the left right button to set BACK Go back to the previous menu 19 EXIT Log out the system menu Menu Password Move the cursor to the MENU PASSWORD and the click the confirm button to go to the fourth menu PASSWORD PASSWORD SETTING 1 2345 BACK 6 7890 SAVE BACK e PASSWORD Enable this function here so that you set password is valid This function is on by default after you set password e SETTING Click the confirm button to go to the password setup interface Please use the left right button to set the value and then click the confirm button to confirm current option Move the cursor to the SAVE button and then click the confirm button to save current setup Click the BACK button to go to the previous menu e BACK Go back to the previous menu e EXIT Log out the system menu If you have forgot your password After three times of login failure system may pop up an 8 digit internal code Please contact our technical engineer for help Heater Control Move the cursor to highlight HEATER CONTROL button and then click confirm button You can go to the 4 menu HEATER CONTROL OPEN TEMPERATURE COLSE TEMPERATURE BACK HEATER
22. et preset auto pan auto scan auto tour auto pattern idle motion time task privacy mask and etc ALARM SETTING Set dome alarm number action contact replay out reset time and etc IR LIGHT SETTING Set dome IR sensitivity control mode medium and far light bright far light bright IR light compensation and etc EXIT Log out the system menu 3 4 Menu Operation In the speed dome main menu you can use the left right button on the keyboard or in the speed dome terminal menu to configure the system menu Before setup please move the cursor to the current item you want to configure In main menu please click confirm button to go to the sub menu or use left right key to configure setup Use up down button to select back option and then click confirm button to go back to the previous menu Use up down button to select exit option and then click confirm button to log out system menu All setup here will not lose when encounter power failure 3 4 1 System Information INITIALIZATION INFORMATION ADDR INFORMATION SYSTEM TIME SETTING SET NORTH LANGUAGE ENGLISH FACTORY DEFAULT RESTART BACK EXIT INITIALIZATION INFORMATION Move the cursor to INITIALIZATION INFORMATION and then click confirm button to go to the third submenu ADDR INFORMATION Move the cursor to SITE INFORMATION and then click confirm button to go to the third submenu SYSTEM TIME SETTING Move the cursor to SYSTEM TIME SETTING and then click
23. lf diagnosis There is a noise Power supplying is inadequate Replace power supplying Mechanical malfunction Need electrical engineer help 3 Video signal loss occurs in high speed rotation Power supplying is not sufficient Replace power supplying 4 Video signal is not Successive Circuit connection is too loose Video switch or power problem Connect tightly Need electrical engineer help 5 Video is not clear Focus is in manual mode Control manually Dome cover is dirty Wash dome cover 6 During camera switch there is a tilt movement in the monitor Camera power is not in the same Phase When several domes are connected to one transformer please connect the transformer output cable to the domes same side 25 6 Appendix I Lightening Protection and Surge Protection This series speed dome adopts TVS lighting protection technology It can effectively prevent damages from various pulse signals below 4000V such as sudden lighting and surge While maintaining your local electrical safety code you still need to take necessary precaution measures when installing the speed dome in the outdoor environment The distance between the signal transmission cable and high voltage device or high voltage cable shall be at least 50 meters Outdoor cable layout shall go under the penthouse if possible For vast land please use sealing steel tube un
24. move the cursor to Save button to save current setup NIGHT TIME Current setup becomes valid when day night mode is Time Move the cursor to DAY TIME item and then click confirm button to go to setup Please user up down button to set the value After completed setup please click confirm button to exit and move the cursor to save button to save current setup THRESHOLD The speed dome can switch the day night mode when it reached the threshold you set here SAVE This button is for DAY TIME and NIGHT TIME setup After you set the day time or night time you need to move the cursor here and then click confirm button to save current time setup For other setups you do not need to use this button BACK Go back to previous menu EXIT Log out system menu 3 4 3 4 Focus Setup FOCUS MODE FOCUS LIMIT AF SENSITIVITY IR CORRECTION BACK e FOCUS MODE It is to set the camera focus mode It includes several modes such as auto manual semiautomatic Please use the left right button on the keyboard or in the speed dome terminal menu to set FOCUS LIMIT It is to set the camera focus limit Please use the left right button on the keyboard or in the speed dome terminal menu to set AF SENSITIVITY It is to set the camera focus sensitivity Please use the left right button on the keyboard or in the speed dome terminal menu to set IR CORRECTION It is to set the camera IR light focus correction Please use the left
25. o Figure 4 4 1 Keyboard E 1 Figure 4 4 Speed dome protocol is open and supports multiple popular system platforms in today s market Please contact us freely if some matrix systems do not support dome camera communication protocol The most direct and easy way is to use current system to process video signal and add some control keyboards to control speed dome See Figure 4 5 Matrix or multiple image Processor Keyboard Figure 4 5 24 5 FAQ 5 1 Please clean dome cover regularly to get vivid image Daily Maintenance Handle the cover with care Use water to wash Don t use cloth to clean Use mild detergent to clean if there is too much dust Note The sweat from your hand may erode plating surface your nail may scrape dome cover result in blur image 5 2 Problems and Solutions SYMPTOM CAUSE SOLUTION 1 No self diagnosis no video signal when connect dome to power Red LED is not on Your power supplying does not apply to the power Or connection is too loose Power off or transformer problem Check 24V AC power is connected or properly earthed Check 24V AC power supply condition or check transformer Red LED light on the power board is on 24V AC power supplying is low Something wrong with power board Use multimeter to check dome load is below 24V AC or not Please contact retailer to replace power board 2 No se
26. o current option and then click confirm button you can go to the third menu DAY NIGHT Set day night mode Move the cursor to current option and then click confirm button you can go to the third menu FOCUS SETUP It is to set the camera focus mode focus limit and etc Please move the light to highlight current item and then click the OK button to go to the next level menu ZOOM SPEED The bigger the value the faster the speed Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE It is to adjust the lens to achieve clear video Please use the left right button on the keyboard or in the speed dome terminal menu to set APERTURE RESTRAIN System can auto reduce the aperture to lower the video noise when it is in low illumination environment Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes the following options DIGITAL ZOOM DIGITAL ZOOM LIMIT PICTURE FLIP FREEZE FUNCTION OUTPUT MODE CAMERA FACTORY DEFAULT SETUP and CAMERA RESTART Please use the left right button on the keyboard or in the speed dome terminal menu to set DIGITAL ZOOM You can use the left right button to enable disable the digital zoom function DZOOM LIMIT Here you can set the threshold of the digital zoom Please use the left right button on the keyboard or in the speed dome terminal menu to set e PICTURE FLIP There are two
27. ome has some new features It supports 120M IR night vision It supports various languages real time clock function and protocol auto recognition It supports 360 continuously pan 100 tilt and 180 auto flip It can realize no blind spot monitor This series product can be widely used in remote monitor environment such as electric power customs and water conservancy 1 2 Features This series speed dome has the following features 1 2 1 On Screen Menu This series product menu supports multiple languages It is easy for you to view dome information and configure dome camera parameters 1 2 2 Proportional Pan and Tilt This function keeps the image from moving too fast when there is a large amount of zoom This series speed dome continually decreases or increases pan and tilt speeds in proportion to depth of zoom When zooms speed is increasing the camera moving speed becomes slow When zooms speed is decreasing the camera moving speed becomes fast 1 2 3 On screen Tips Via menu here you can view Call preset and preset ID speed dome title when calling touring Dome system temperature Optional You can disable this function Software version Optional You can disable this function Dome address Optional You can disable this function 1 2 4 Preset Setup and Call Preset function is to save the address information such as PTZ pan tilt focus and etc to the memory so that you can quickly adjust the dome and PTZ to the co
28. onfirm button to set BACK Go back to previous menu EXIT Log out system menu 3 4 4 1 Preset Setup PRESET NO 001 TITLE PRESET1 SETTING CALL BACK Move the cursor to PRESET button and then click confirm button to go to set interface PRESET NO Please use left right key to modify preset number The different protocols support different preset values TITLE Title text is the label used for you to identify the camera System will automatically name a title for the camera SETTING Please input preset number first and then select the monitor zone Please move the cursor to setting and click confirm button The system will pop up a message PRESET Here means preset number And the SETTING column pops up an OK Now you successfully added a preset Please note you need to enable display preset title function first Main menu display setting gt preset title Repeat the above procedures to set more presets Once you want to modify a preset you can input the preset number you want to modify and then follow the above steps to set the preset You can successfully modify a preset content CALL Here is to call preset Move the cursor to PRESET NO and then input corresponding preset value Then move the cursor to CALL and then click confirm button to go to a preset BACK Go back to previous menu EXIT Log out system menu For PELCO protocol user please refer to the following special functions 13 Call prese
29. reboot the speed dome to get all the setups activated Open the dial switch cover on the bracket the interface is shown as below See Figure 2 1 You can see there are two dial switches on the PCB board The two dial switches can specify the speed dome parameter such as address protocol baud rate and etc For the baud rate dial switch buttons 1 3 is NC 4 is the 1200 resistance ON is to connect to the 1200 resistance When the button is ON it is 1 In dial switch buttons 1 is the lowest bit and the 8 is the highest bit Open dial switch cover Parity Baud Rate Setup Address Setup Figure 2 1 Please note this series speed dome can automatically recognize the industrial standard protocol PELCO D PELCO P usually you do not need to set the protocol Please refer to the baud rate sheet for detailed information ODD NONE Please refer to the parity setup sheet for detailed information Baud Rate 9600bps 4800bps 2400bps 1200bps 2 2 Set address dial switch The encode mode adopts binary system 1 to 8 is valid bit The highest address bit is 255 You can refer to the following sheet for more information Address 1 2 3 4 5 6 7 8 1 OFF OFF OFF OFF OFF OFF OFF OFF 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF O
30. rrect position 1 2 5 Auto Scan Camera scans back and forth regularly in a horizontal field Here you need to set left and right limit and Scan speed 1 2 6 Auto Tour Add presets into a routine in a desired order and then set time and stop duration for each address The dome will begin an auto touring between these presets 1 2 7 Auto Pattern Memorize dome operation such as pan tilt and zoom to repeat You can call it to repeat the previous operation 1 2 8 Privacy Masking Privacy masking is a user defined four sided area that can not be viewed by you The masking area will move with pan and tilt functions and automatically adjust in size as the lens zooms 1 2 9 Action on Alarm There are 7 alarm inputs NO NC and 2 NO outputs via socket connector Alarms can be individually programmed to initiate an associated operation when received 1 2 10 Auto Flip As long as you continue to hold the keyboard joystick in the down position the dome rotates 180 degrees and repositions itself for uninterrupted viewing of any subjects that passes directly beneath the dome 1 2 11 Self diagnosis There is a self diagnosis procedure when dome boots up e Tilt and vertical engine check Camera diagnosis it mainly includes address baud rate parity and etc 1 2 12 Day Night Mode B W amp Color Mode There are several modes such as photosensor auto manual This function needs the speed dome driver camera supported 1 2 13 Auto Focus Support auto focu
31. s function 1 2 14 Backlight Compensation Balance the brightest and darkest sections of a scene to produce a more vivid picture 1 2 15 Pan Tilt and Zoom Supports zoom in and zoom out during tilt and pan movement In this period auto focus and auto iris can still get vivid image 1 2 16 3D Intelligent Location Support 3D intelligent positioning function speed dome can auto track to the specified zone 1 2 17 Idle Status When there is no available order for specified period the speed dome can implement previously set idle operation The idle operation can be preset scan tour pattern and etc You can set the operation ID 1 2 18 Power up The speed dome executes the power up operation after it rebooted and completed the initialization The power up function includes auto preset scan tour pattern and none 1 2 19 Image Stabilization Flip You can enable image stabilization flip in the menu The stabilization function can guarantee the video stability when there is any vibration on the speed dome installation environment The flip function allows you to view continuous video This function needs the speed dome driver camera supported 2 Protocol Baud Rate Address Setup Before you operate you need to set address baud rate and parity Otherwise you can not control the product 2 1 Protocol and Baud Rate Setup Please configure the following settings before begin controlling dome e Baud rate Parity Address Note Please
32. set camera exposure compensation Please use the left right button on the keyboard or in the speed dome terminal menu to set SLOW AE In the strong light environment you can lower the camera exposure speed to capture the image and enhance the definition The larger the value the faster the speed Please use the left right button on the keyboard or in the speed dome terminal menu to set e SLOW SHUTTER In lower illumination environment you can lower the cameras auto exposure time to capture the image and enhance the definition Please use the left right button on the keyboard or in the speed dome terminal menu to set NEXT PAGE It includes AGC GAIN LIMIT SLOW SHUTTER LIMIT NOISE REDUCTION 3D NOISE REDUCTION BLC WDR BACK and EXIT Move the cursor to the item and then click the left right button to set o GAIN LIMIT It is to set auto gain high limit Please click the left right button to set o SLOW SHUTTER LOW LIMIT It is to set slow shutter low limit Please click the left right button to set o NOISE REDUCTION There may noise when the camera is monitoring the low illumination environments You can use the digital filter to process the noise to guarantee the clear video NOISE REDUCTION It is to set the speed dome 3D noise reduction setup Please use the left right button on the keyboard or in the speed dome terminal menu to set o BLC Itis an abbreviation for back light compensation System can compensate th
33. software It is to say you can use menu to modify dome address The value ranges from 0 to 255 BACK Go back to the previous menu EXIT Log out system menu 3 4 1 3 System Time Setting YEAR MONTH DATE WEEK HOUR MINU SAVE BACK EXIT Move the cursor to SYSTEM TIME SETING and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click confirm button to save current setup After you see speed dome menu displays OK you can see the setup is valid now 3 4 2 Display Setting PRESET TITLE AZIMUTH DISP TIME DISP POSITION ZOOM DISP INSIDE TEMP TITLE DISP BACK Move the cursor to DISPLAY SETUP and then click confirm button you can go to the third submenu Please use the left right button on the keyboard or in the speed dome terminal menu to set After completed setup please click save button to save current setup PRESET Display dome preset title or not Please use the left right button on the keyboard or in the speed dome terminal menu to set You can go to Function Setup gt Preset section to set corresponding preset value and preset title AZIMUTH DISP Display dome current coordinates or not Please use the left right button on the keyboard or in the speed dome terminal menu to set TIME DISP Display dome system time or not Please use the left right button on the keyboard
34. sor to SAVE and then click confirm button to exit Please note you need to click SAVE button to save current privacy mask setup so that the privacy mask region can move along with the PTZ movement to always cover the object you want to shield PRIVACY NO Here is to set privacy mask zone Please use the left right button on the keyboard or in the speed dome terminal menu to set You can call corresponding privacy mask zone number if you have successfully set one System supports 1 24 privacy mask zones Please note the privacy mask amount may vary due to different product series PRIVACY MASKING There are two settings on and off This function is only valid after you set a privacy mask zone SETTING It includes the fourth menu You can set privacy mask zone size and save RESIZE It is to adjust the privacy zone size Move the cursor to current item and use the left right button on the keyboard or in the speed dome terminal menu to set Please continue pressing direction button to widen or narrow zone size is to narrow the horizontal width and is to widen the horizontal width 1 is to widen vertical height and is to narrow the vertical height SAVE Here is to save user setup BACK Go back to previous menu EXIT Log out system menu Power Up Move the cursor to the POWER UP item and then click the confirm button you can go to the fourth menu POWER UP PARAMTER BACK POWER UP It is to set th
35. system information The above interface disappears after speed dome received the first command or the display time lasts for 4 minutes ADDR Here you can view dome address information For example 001 H H is the hardware address number S is software address mode BR Dome communication baud rate PARITY Communication parity bit format VERSION Dome software version When you are using the control keyboard or the matrix host to control the device please make sure the control parameter of the keyboard or the matrix host is the same with the speed dome OSD including address baud rate parity Please make sure the cable connection is OK 3 3 Main Menu You can open speed dome menu via control keyboard matrix or speed dome control terminal SYSTEM INFORMATION DISPLAY SETTING CAMERA SETTING FUNCTION SETTING ALARM SETTING IR LIGHT SETTUING EXIT SYSTEM INFORMATION Dome system information address information system time set north direction language factory default setup and restart and so on DISPLAY SETTING Display dome preset azimuth display time direction zoom and dome internal temperature and etc information CAMERA SETTING Display dome white balance setup exposure setup day night setup focus setup zoom speed aperture setup aperture restrain digital zoom image flip image freeze image stabilization factory default setup camera restart and etc FUNCTION SETTING S
36. t Call preset 28 or preset 95 to go to dome menu Call preset 29 or preset 99 to go to scan Call preset 24 or preset 81 to go to pattern Call preset 25 or preset 82 to go to tour Call preset 30 or preset 96 to stop scan or pattern Call preset 31 or preset 83 to begin rotation Call preset 33 to enable PTZ 180 degrees rotation Call preset 34 to set dome position as O Set preset Set preset 26 or 92 to set scan left limit Set preset 27 or 93 to set scan right limit Set preset 22 or 79 to begin record Set preset 23 or 80 to stop record 3 4 4 2 Pan PAN SPEED CALL STOP BACK Move the cursor to PAN button and then click confirm button to go to setup interface PAN SPEED Set dome rotation speed Please use the left right button on the keyboard or in the speed dome terminal menu to set CALL Move the cursor to CALL item and then click confirm button The dome begins 360 degrees continuous rotation e STOP Highlight stop item and then click confirm button The dome stops rotation BACK Go back to previous menu EXIT Log out system menu 3 4 4 3 Auto Scan AUTO SCAN NO SET LEFT LIMIT SET RIGHT LIMIT SCAN SPEED CALL STOP BACK Move the cursor to SCAN button and then click confirm button AUTO SCAN NO Here is to set auto scan number Please use the left right button on the keyboard or in the speed dome terminal menu to set SET LEFT LIMIT Here is to set camera left address Click confirm b
37. t you system has memories one pattern 15 CALL Here is to activate pattern Input pattern number move the cursor to CALL and click confirm button system begins running pattern STOP Here is to stop current pattern Input pattern number move the cursor to STOP and click confirm button System stops current pattern BACK Go back to previous menu EXIT Log out system menu Note The dwell time between two orders should be less than one minute otherwise system will set to default value as one minute After click PROGRAM STOP do not click CALL button before icon disappears completely Any manual operation during the pattern procedure will terminate current dome pattern operation 3 4 4 6 Idle Motion IDLE MOTION IDLE TIME IDLE MOTION PARAMETER BACK When there is no available command for specified time dome automatically goes on the previous set functions IDLE MOTION There are two modes ON OFF Please use left right key to set IDLE TIME System idle period Please use the left right button on the keyboard or in the speed dome terminal menu to set IDLE MOTION There are several functions you can select NONE PRESET SCAN TOUR PATTERN Please use the left right button on the keyboard or in the speed dome terminal menu to set PARAMETER It is to set idle motion SN System can implement the corresponding action when it is idle for the specified period Click the left right bu
38. to the previous menu EXIT Log out the system menu 3 5 Dome Abnormal Phenomenon Operation 3 5 1 Restore to Factory Default Setup From main menu gt SYSTEM INFORMATION move cursor to FACTORY DEFAULT and click confirm button Dome will reboot and all the setups restore to factory default setup 3 5 2 PTZ Movement is not smooth From menu to SYSTEM INFORMATION move cursor to RESTART and click confirm button This reboot will not modify all activated setup such as preset tour and pattern 21 4 Cable Connection The speed dome combination cable includes video cable connection port RS485 connection port alarm input and output port Please refer to the label for detailed information e Slight difference may be found in the port amount since some functions are optional Name Function 485 A 485 A It is to control dome built in PTZ B 485 B It is to control dome built in PTZ GND Ground VIDEO OUT Video output port AC24V 24V power port Connect to the power cable EARTH Ground port Relay in out interfaces is shown below Name Function Alarm out 1 2 a Two alarm output channels When there is an alarm from current channel system activates relay or not b Alarm output relay default setup is NO You can use the jump cap near the power board relay to set C NO Normal open alarm output d NC Normal close alarm output 1 2 Alarm out com Alarm input ground end
39. tton to set SAVE Move the cursor to SAVE and click confirm button to save current setup BACK Go back to previous menu EXIT Log out system menu 3 4 4 7 Time Task Schedule task TASK NO TIME TASK TASK SETTING TASK INFORMATION DELETE TASK BACK e TASK NO Here you can set task number Please use the left right button to set e TIME TASK The schedule task allows the speed dome to implement corresponding setup during the specified time There are two options on off Please use the left right button on the keyboard or in the speed dome terminal menu to set e TASK SETTING Here you can set task time operation operation SN and etc Please click the confirm button to go to the fourth menu to set 16 TASK INFORMATION Here you can view the corresponding task information Please click the confirm button to go to the fourth menu to set DELETE TASK Please input the task number to be deleted in the TASK NO and then move the cursor to the current item Click the confirm button you can remove all the setups in the current schedule task Now current task is null BACK Go back to the previous menu EXIT Log out the system menu Task Setting Move the cursor to the TASK SETTING and then click the confirm button you can set the task begin time end time action and etc WEEK START TIME END TIME RUN ACTION PRESET NO SAVE BACK WEEK Here you can set the week information Please use the left right
40. ue equ he ke ue d n eerie is 1 2 18 Power mede dU ERR 1 2 19 Image Stabilization Flip 2 1 tetto ttti tetto lette eon tee tete eene etel eo one 2 PROTOCOL BAUD RATE ADDRESS SETUP suser renere rn 3 2 1 Protocol and Baud Rate Bc UR M 2 2 Set address dial SWItCh asi eie e Ee ESTERE ek e ocn o Poss qe opas esa diu PE o rese Pug 3 1 MENU INGEN QST TIED IET 3 2 Self diagnosis System Information 3 3 ETIAIN H 6 3 4 Menu m 7 S T ME CHINO 7 9 42 Dipa Seting ote rtm EO De RR ORE 8 24 3 Camera Settings oeio eee lie ec ee dede etel ee aces eee eden i eve ete ee eds 9 3 424 Funcion SOUL eos erret ee rr ER er E ROB DUE Ue le Ae a b ERR Ge qd te tie rers 12 3 4 5 Alarm Setup REGI RR AER ER DP I He dde 20 3 46 JR Egit Setting n ar ERE AT ERR ED AR UU ROO 21 3 5 Dome Abnormal Phenomenon Operation ecce eee esee ee ee eene ento etse te eost sete ens P essen sse seen senses en en 21 9 1 Restore to Factory
41. utton to save current setup SET RIGHT LIMIT Here is to set camera right address Click confirm button to save current setup SCAN SPEED Please use the left right button on the keyboard or in the speed dome terminal menu to set CALL Please input auto scan number first and then please move the cursor to CALL and click confirm button to activate auto scan function STOP Here is to terminate auto scan function BACK Go back to previous menu EXIT Log out system menu 3 4 4 4 Auto Tour TOUR NO TOUR SETTING DELETE TOUR CALL STOP BACK Move the cursor to highlight TOUR item and then click confirm button to go to setup interface 14 TOUR NO Here is to ser tour number Please use the left right button on the keyboard or in the speed dome terminal menu to set SETTING Move the cursor to TOUR setting item and then click confirm button You can see the following interface Here you can add or remove the preset and set the corresponding dwell time and call speed NO PRESET DWELL SPEED 01 000 005 013 02 000 005 013 03 000 005 013 32 000 005 013 BACK EXIT B DWELL Here is t set dwell time Please use the left right button on the keyboard or in the speed dome terminal menu to set SPEED Here you can set the speed value When you move the cursor to one tour number you can use left right button to turn the page When you move the cursor to one tour number please click confirm
42. versy please refer to the final explanation of us Please visit our website or contact your local service engineer for more information 28
Download Pdf Manuals
Related Search