User Guide - Performance Audio
Contents
1. VOICE SOLO XT PERSONAL VOCAL MONITORS VSM 200P XT USER MANUAL IMPORTANT SAFETY INSTRUCTIONS The lightning flash with an arrowhead symbol within an The exclamation point within an equilateral triangle is AN equilateral triangle is intended to alert the user to the A intended to alert the user to the presence of important presence of uninsulated dangerous voltage within the operating and maintenance servicing instructions in the product s enclosure that may be of sufficient magnitude to literature accompanying the product constitute a risk of electric shock to persons Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Only use attachments accessories specified by the manufacturer O Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged2. feedback describes the sudden shriek or howl that happens when a mic hears the speaker s sound and amplifies it The following tips should help you to minimize the risk Always raise the volume level slowly singing something into the mic as you do so Feedback will give you a little warning if you listen carefully When you hear a slight ringing while you check the mic lower the level a little and this will become your safe monitoring level Consider your placement When VoiceSoloP XT is slightly off to one side as opposed to directly in front of you you will hear it better and can hear well with less level Side placement is also optimal when using mics with a hyper cardioid pickup pattern because in exchange for reduced sensitivity at the back sides of the mic there is more sensitivity directly at the back of the mic When using handheld mics near VoiceSoloP XT never point the mic at the speaker This seems obvious yet it happens all the time When VoiceSoloP XT is fed by an amplified monitor send ensure that the monitor send is Pre EQ This allows you to add EQ to the main PA sound on your channel but to send a flat no EQ signal to VoiceSoloP XT With a good mic and a strong singer a flat monitor is likely to be louder than an EQ d one 11 Specifications Connectors Connectors 2 paralleled Speakon combo jacks that accept Speakon or 1 4 connectors Speaker Speaker 6 5 inch ICT custom designed point
3. liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Warning e To reduce the risk of fire or electrical shock do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the equipment Service There are no user serviceable parts inside e All service must be performed by qualified personnel Table of Contents Introduction 4 Front panel diagram 6 Back panel diagram Mic stand mounting procedure 8 Using VoiceSoloP XT 11 Specifications 12 Specifications interface and features are subject to change without notice due to continued product improvement VoiceSolo VSM 200P XT Rev 1 0 3 English version Introduction Welcome to VoiceSoloP XT The TC Helicon VSM range of near field live monitoring speakers is a new concept in personal monitoring TC Helicon strives for excellence in all things related to vocals and the VSM range builds upon the success and worldwide reputation of TC Helicon s vocal expertise If you can t hear yourself correctly in a live situation it s hard to produce a good performance VSM monitors are designed to integrate into a boom style microphone stand bringing the speaker close to the performer This yields a wide range of benefits over ex
4. that it is capable of driving a 2 Ohm load Note that all Ohm ratings are specified with the volume control set to maximum VOICESOLO VSM 200P XT 2 Power handling legend This legend describes the amount of power your VSM 200P XT will accept with various types of program material 60W AVERAGE Also known as RMS this means that VoiceSoloP XT will accept audio of constant level e g a sine wave test signal of 60 watts for an extended period of time 120W PROGRAM This rating describes how many watts VoiceSoloP XT can accept over an extended period of time with dynamic program material such as what a band or singer would produce 240W PEAK This is the maximum VoiceSoloP XT can withstand for a very brief period of time Mic Stand Mounting VoiceSoloP XT Placement Options 1 Separate the boom from the stand by unscrewing the boom from the vertical shaft of the microphone stand To voles Der pieced nes bie uias do this tighten the clutch you use to raise and lower the vera alone Jato esa mies dne meines stand first This makes it easier to unscrew the boom mentor ens night p system onagra tO Dee section Hold the base of the stand with one hand and at home for practice or jamming turn the boom counterclockwise looking down from the top with the other hand 9 Mic Stand Mounting 2 Screw the Mic Stand Mounting Insert on to the vertical Mic Stand Integration shaft of the microphone st
5. and If your stand has 3 8 What you need European thread it will be necessary to use a 5 8 to 3 8 thread adapter commonly included with both VoiceSoloP XT microphone stands and microphone clips Tripod microphone stand with boom must be the style where the boom may be unscrewed from the vertical shaft of the microphone stand Mounting e VoiceSoloP XT adaptor hardware including Insert es Mic Boom Mount Attachment Mic Stand Shaft a Mic Stand Mounting insert Tip If you find that your VoiceSoloP XT wobbles on the stand try wrapping the Mic Stand Shaft threads with Teflon thread tape before screwing on the Mic Stand Mounting Insert Teflon thread tape can be found at stores that sell plumbing supplies Mic Stand Mounting 3 Place VoiceSoloP XT on the mic stand so the stand 5 Screw the Mic Boom Mount Attachment into your boom goes into the hole on the bottom of the VoiceSoloP XT If you don t need to mount VoiceSoloP XT on a boom stand you are finished with your setup If you require the boom continue to the next step 6 Lift the lid on VoiceSoloP XT and while holding it open slide the Mic Boom Mount attachment on the boom into slot on top of the monitor and let the lid close 4 The Mic Boom Mount is found in the bag of parts that came with your VoiceSoloP XT There are two versions a thin one for European stands and a wider one for the rest This adapter c
6. ere those who work with voice are able to bring out its very best and where the possibilities of vocal craft are endless The company s mission was galvanized by a simple question Isn t it time that someone finally provided dedicated tools and solutions for voice TC Helicon is revolutionizing the vocal channel by providing innovative tools and solutions for people who create and work with the speaking and singing voice Our customers include the most demanding of live performers producers broadcasters and recording engineers Enjoy The TC Helicon Team a TC Group company Introduction Preliminary Recommendations The VoiceSoloP XT VSM series of monitors are capable of very high sound pressure levels SPLs especially at the close range when integrated onto a microphone stand They were designed this way to be able to be loud enough to compete with live acoustic drum kits In situations where high monitoring volumes are required we recommend that ear protection be used For continuous exposure we recommend the occasional use of a sound level meter capable of measuring the sound level over a period of exposure according to noise control standards This should be used to check that noise levels are always within safety limits Unpacking Open the box from the top and remove cabling Lift out styrofoam insert then using both hands lift out VoiceSoloP XT Remove plastic bag from VoiceSoloP XT Nothing in your speakers sho
7. isting wedge type or in ear options such as Lower monitor bleed into the main PA sound High volume level before feedback Better interaction with audience stage space is reclaimed from floor wedges and ear plug barriers are not required as in in ear monitors The VSM monitors use a two way point source ICT driver that eliminates the problem of hearing separated high and low frequencies which happens when listening to conventional speaker systems This is especially important when used on a microphone stand as the speaker is located very close to the listener and the separation would be more evident VSM 200P XT Features Improved high frequency response in the critical 4 to 10 kHz range resulting in higher accuracy and smoother sound Quick mic stand set up Integrates with boom so the same stand is used for the monitor and microphone Versatile placement options provided by dual stand mounting holes and dual bevelled edges for floor mounting Two way point source 6 5 ICT driver for optimal near field live monitoring High power capacity 240W peak Cast aluminum enclosure for maximum rigidity and minimum cabinet resonance Front panel mounted volume control for easy access About TC Helicon ICHELICON OCAL TECHNOLOGIES TC Helicon s core value is that the voice is the world s most beautiful instrument Therefore everything TC Helicon does is dedicated to this instrument TC Helicon envisions a world wh
8. onnects the boom of your mic stand with VoiceSoloP XT It is designed to fit into the top receptacle in VoiceSoloP XT Mic Stand Mounting T Your VoiceSoloP XT should now look like this Loosen Boom 2 Still holding the boom so that it does not swing away turn the lock nut counter clockwise until its snug against the bottom of the boom Note that it s not possible to completely tighten the lock nut with your fingers the final action is done by swinging the boom snug against the lock nut Lock Nut Adjusting the Boom To optimize line of sight and audibility it is usually better to have the monitor situated somewhat beside the singer To do this it is necessary to adjust the position of the boom 3 The steps required to adjust the position of the boom are as follows After tightening the lock nut with your fingers swing the boom left tightening to the desired position It may be necessary to go through steps 1 3 a few times to get the boom tightly where you want it The boom must be tight or the weight of the mic can cause it to swing out of 1 With the VoiceSoloP XT integrated into the mic stand and position boom loosen the boom by rotating to the right while holding onto a corner of VoiceSoloP XT Read the next section to learn how to connect your new VoiceSoloP XT 10 Using VoiceSoloP XT Introduction The following paragraphs should be read at least once to learn more about safe and successful
9. source driver including inductively coupled tweeter Nominal impedance 8 ohms Power 120 Watt Program 240 Watt Peak power handling Sensitivity I Watt 1 meter 90 dB 1 kHz octave band Conical dispersion 90 degrees Frequency response 120 Hz 2 kHz Peak SPL 116 dB 5 meter Case Case Enclosure of molded aluminum with integral bass port Color Black Dimensions H x W x D 9 x 7 x 9 75 23 cm x 18 cm x 25 cm Shipping weight 11 Ibs 5 kg Net weight 9 2 Ibs 4 2 kg 12
10. uld rattle Inspect each speaker for signs of transit damage In the unlikely event of this having occurred inform the carrier and the supplier Keep all the packaging if damage has occurred as this will show evidence of excessive handling forces It is also a good idea to keep the packaging if possible for future transportation Registering VoiceSoloP XT There are two methods for registering your VoiceSoloP XT Online visit www tc helicon com VoiceSolo and click Product Registration in the left hand column Mail complete and return the registration card included with your product Support If you run into technical challenges TC Helicon will be more than happy to help There are a number of sources for product support We ve prioritized them below according to the speed at which you will access the help information 1 Manual The manual for VoiceSoloP XT VSM 200P is a good source of application information and answers for common questions 3 On Line visit www tcsupport tc to search and ask for answers on up to date questions about VoiceSoloP XT 4 Phone International 45 8742 7000 USA amp Canada 818 665 4900 Front Panel Diagram f VOLUME 1 VOLUME level control This detented attenuator allows you to adjust your monitor level while staying close to your mic This control functions differently than the volume control on an amplifier As you turn up the volume on an amplifier the amp works successivel
11. use of VoiceSoloP XT Making Connections Before connecting speaker cables First of all turn the amplifier that will drive VoiceSoloP XT off This is a general rule when connecting any speaker to an amp Plug in the speaker cable s Connect a proper speaker cable between your amplifier and VoiceSoloP XT s IN THRU jacks Note that speaker cables and input cables with 1 4 jacks look alike Do not use input cables like the ones you would use to connect an instrument to an amp Only use quality speaker cables available from your dealer If you plan to chain multiple VSM 200P XTs onto a single amplifier channel you may connect cables from either jack to the next speaker Read the Back Panel Diagram note on page 8 regarding chaining VoiceSoloP XTs Turn down the amp If the amp has a volume control it s good practice to turn it to minimum before applying power Also ensure that the device driving the amplifier has its volume turned off Apply power to your amp After powering up turn up the input control on the amp if it features this Raising the level Adjust your mixer so that your mic or instrument is fed to a monitor send Raise the send level slowly while you sing or say check into the mic until the level is sufficient You re now ready to perform with VoiceSoloP XT Overcoming feedback As in any open speaker and mic combination there is the threat of feedback For those who aren t familiar with the term
12. y harder to produce more volume With the VSM 200P XT volume control however the amp continues to work hard whether your VoiceSoloP XT s volume control is turned up full or down With a powerful amp and medium volume level expectations this control can be used throughout its range With less powerful amplifiers and high volume expectation the most efficient path is to leave the VSM 200P XT volume control up full and for you to control volume with your mixer and or amplifier 2 Tuned bass port This allows VoiceSoloP XT to produce low frequencies It is also useful as a handle when carrying the unit Back Panel Diagram TCHELICON L TECHNOLOGIES POWER HANDLING 60W AVERAGE 120W PROGRAM 240W PEAK 1 Speakon combo input jacks These jacks allow either a 1 4 speaker cable or Speakon equipped speaker cable to connect to VoiceSoloP XT These jacks are paralleled and can be used to chain several VSM 200P XT units together Thus both jacks are designated as IN THRU A note about chaining multiple VoiceSoloP XTs Your VSM 200P XT has an impedance or ohms rating of 8 Ohms Chaining two VSM 200P XTs together lowers the impedance the amp will have to drive to 4 Ohms Most amps will work fine at 4 Ohms even when pushed to produce loud volume levels Chaining three VSM 200P XTs will lower the impedance to 2 6 Ohms and adding a fourth VSM 200P XT will bring the impedance to 2 Ohms Consult your amplifier s manual to confirm
Download Pdf Manuals
Related Search