- Mayflex
Contents
1. Basic Setting These are the basic settings of the unit Click on the menu on the left to access the respective settings page Configure LAN IP and select WAN type DHCP Server The settings include Host IP Subnet Mask Gateway DNS and WINS configurations Wireless Wireless settings allow you to configure the wireless configuration items Change Password Allow you to change system password 16 Basic Settings gt Primary Setup This page lets you change the LAN Local Area Network settings on your WBR 3800 MobilSpot and WAN Wide Area Network connection Primary Setup HELP Setting gt LAN NetMask 255 255 2550 gt WAN s MAC Address 00 50 18 00 00 01 8806 Clone MAC IC Enable checking wired WAN alive Internet host gt Auto Backup Static IP Address ISP assigns you a static IP address C Dynamic IP Address Obtain an IP address from ISP automatically C Dynamic IP Address with Road Dynamic IP Address with Road Runner Session Runner Session Management Management is a WAN connection used in Australia eg Telstra BigPond PPP over Ethernet Some ISPs require the use of PPPoE to connect to their services C L2TP Some ISPs require the use of L2TP to connect to their services C PPTP Some ISPs require the use of PPTP to connect to their services C 3G 3G unenee AA gt Assigned IP Address 0 0 0 0 optional 17 VI VII V2. AutoMDI MDIX This provides Ethernet cable LAN Port access Step 4 1 Connect the power adapter to the receptor on the back panel of your WBR 3800 MobilSpot 2 Then plug the other end of the power adapter into a wall outlet or power strip e The 3G LED will turn ON to indicate power has been applied e Other LEDs will flash ON and OFF as the WBR 3800 MobilSpot performs initialization and Internet connection processes This will take a few minutes e When complete the following LEDs will illuminate green 3G WAN LAN and WLAN Chapter 3 The Configuration Menu Once properly configured the WBR 3800 MobilSpot will obtain and assign IP address information automatically Configuration settings can be established through the Web Based Configuration Menu 1 Open a web browser Internet Explorer Firefox Safari and type in the IP Address http 192 168 0 1 Note Browser will automatically add port 2005 on the IP Address eg http 192 168 0 1 2005 If you have changed the default IP Address assigned to the WBR 3800 ensure you enter the correct IP Address Go 1 S di E WBR 3800 MobilSpot Portable Wireless Hotspot 2 Type in password without guotes in the Password box Then click Login Note password is the default login password for the unit Ri IENU 5 Status 3 System Status HELP Item WAN Status Sidenote 3 Click on Wizard then click Enter to star
3. deny to allow or deny the clients whose MAC addresses are not in the list e Association Control To control which wireless client can be associated with this MobilSpot If a client is denied then it means the client cannot send or receive any data via this MobilSpot Choose allow or deny to allow or deny the clients with MAC addresses that are not in the list to associate to the wireless network 34 Security Setting gt Miscellaneous This page allows you to change various miscellaneous security settings Miscellaneous Items HELP Item Setting Enable gt Remote Administrator Host Port 0 0 0 0 180 gt Administrator Time out 600 seconds 0 to disable gt Discard PING from WAN side gt Disable UPnP Save unao Remote Administrator Host Port By default only LAN user can browse the built in web configuration pages to perform administration task This feature enables you to perform administration task from the Internet If this feature is enabled only the specified IP address can perform remote administration H the specified IP address is 0 0 0 0 any host can connect to this product to perform administration task For better security you can specify just one IP address or use subnet mask bits inn notation to specify a group of trusted IP addresses For example 10 1 2 0 24 NOTE When Remote Administration is enabled the web server port will be shi
4. Taiwan Taiwan Taiwan Australia Australia Australia Taiwan Germany Germany Taiwan Taiwan USA Germany Australia Thailand Australia Australia Australia Taiwan Germany Germany Vodafone Willcom Verizon Yiso ZTE Growell Growell Note For the latest compatibility list please see www level1 com GT 3G Quad AX520N PC5740 C893 MF 332 C803 GW 1033C UMTS PHS EVDO EVDO HSDPA CDMA 1X EVDO CDMA2000 1X 56 Taiwan Japan USA USA Australia Taiwan Taiwan
5. e For Wireless Networking a computer with working 802 11b or 802 11g wireless adapter Chapter 1 Introduction The LevelOne WBR 3800 MobilSpot Portable Wireless Hotspot is a high performance tool that supports wireless networking at home work or public place usage The MobilSpot uses either a 16bit or 32bit PC card or USB 3G 3 5G modem adapter for either WCDMA EDGE or EVDO and even HSDPA 3G Broadband services to connect and distribute the Internet to multiple computers It also has a WAN port to connect the WBR 3800 to an ADSL Cable modem or existing gateway router Included is also a Wireless Access Point that supports wireless data transfers up to 54 Mbps The LevelOne WBR 3800 is compatible with industry security features such as WEP WPA and WPA2 to eliminated exposure to unwanted access The LevelOne WBR 3800 MobilSpot also comes equipped with solid firewall features to defend against hackers which is even active when VPN is being used Port Forwarding and UPnP functions make is much simpler to configure and setup a series of port rules required by many online games P2P file sharing and server applications Front LED Indicators Label Status Indicators Flashing Flashes when unit is ready Off Power is Off LAN Flashing Flashes when data is being transferred On Indicates link is active Flashing Flashes when data is being transferred Indicates no active link Indicates WAN link is active Of
6. Enable 4 T Drop Log 2 Ir T Drop Log E 3 Ir I Drop Loa 4 T Drop Log 5 Ir I Drop F Log E 6 T Drop T Log O 7 Ir E T Drop Log 8 Ir I Drop Log 9 T Drop Loa 10 all others L Drop L Log Save unao To enable Domain Filter make sure to tick the Enable tick box e Log DNS Query Check if you want to log the action when someone accesses the specific URLs e Privilege HOST Netmask Setting a group of computers that have privilege to access the internet without any restrictions e Domain Suffix A suffix of URL to be restricted For example com xxx com e Action When someone is accessing the URL that meets the domain suffix what kind of action you want the MobilSpot to take Tick on Drop to block the access and or tick on Log to log this access 32 Security Setting gt URL Blocking URL Blocking will block LAN computers from connecting to a pre defined Web Sites The major difference between Domain Filter and URL Blocking is that Domain Filter requires the user to input suffixes eg xxx com ttt net while URL Blocking only requires user to input a keyword In other words Domain filter can block specific website while URL Blocking can block hundreds of websites by simply a keyword 3 Http URL Blocking HELP Item Setting gt URL Blocking CT Enable URL Enable
7. Primary DNS Secondary DNS To assign DNS Servers optional Primary WINS Secondary WINS To assign WINS Servers optional Gateway The IP address of an alternate gateway optional Clients List Check the DHCP client list Fixed Mapping Take you to the Security gt MAC Control page see page 35 After you finish your selections click either Save to store your settings or Undo to exit Basic Setting gt Wireless This page allows you to configure the wireless feature of the unit J Wireless Settings HELP Item Setting gt Wireless Enable Disable gt WMM Capable Enable Disable gt SSID es zen gt Channel 11 gt Security None D Save Undo WDS Setting 1 Wireless Enabled by default Disabling this will turn off the wireless feature of this unit 2 WMM Capable Choose Enable or Disable WMM WiFi Multimedia function This function provides features that improves audio video and voice applications over the wireless network 3 SSID Service Set Identifier SSID is the name designated for a specific wireless local area network WLAN The SSID s factory default setting is WBR 3800 The SSID can be easily changed to establish a new wireless network Note SSID names may contain up to 32 ASCII characters 4 Channel Channels 1 13 are available to choose from 11 is the default Devices on the network must share the same channel Changing the channel
8. Save Undo To enable URL Blocking make sure to tick Enable To set an URL Blocking rule you will require e URL If any part of the Website s URL matches the predefined word the connection will be blocked e Enable Tick to enable the rule 33 Security Setting gt MAC Control The MAC Control allows you to assign different access rights for different users and to assign a specific IP address to a certain MAC address 3J MAC Address Control HELP Item Setting MAC Address Control Enable T Connection control Wireless and wired clients with C checked can connect to this device and allow DI unspecified MAC addresses to connect I Association control Wireless clients with A checked can associate to the wireless LAN and deny DI unspecified MAC addresses to associate DHCP clients select one zl _Copyto lip ID MAC Address IP Address Wake On Lan A 1 1921680 Trigger 2 1921680 Trigger IT 3 1921680 Trigger 4 e 1921680 Trigger olo Previous page Next page Save Undo To enable MAC Address Control make sure to tick on Enable There are two types of controls available e Connection Control To control which wired and wireless clients can connect to this device If a client is denied access it means the client cannot access the Internet either Choose allow or
9. different channel to avoid interference Please refer to Basic gt Wireless section on page 21 4 Why I am unable to achieve a wireless connection Note An Ethernet connection is required to troubleshoot the WBR 3800 MobilSpot If you have enabled Encryption WEP WPA WPA2 on the WBR 3800 you must also enable encryption on all wireless clients in order to establish a wireless connection Please refer to your wireless adapter manual for more information Move the WBR 3800 and the wireless client into the same room and then test the wireless connection 50 5 e Try disabling all security settings such as WEP and MAC Address Control e Try turning off the unit and the wireless client Then turn both back on again e Ensure that all devices are set to Infrastructure mode e Ensure that the LED indicators are indicating normal activity If not ensure that the AC power and Ethernet cables are firmly connected e Ensure that the IP Address subnet mask gateway and DNS settings are correctly entered for the network e lf you are using 2 4GHz cordless phones X10 equipment or other home security systems ceiling fans or lights your wireless connection may degrade dramatically or drop altogether e To avoid interference change the wireless channel on the WBR 3800 and all devices in your network e Try to keep your product at least 3 6 feet away from electrical devices that generate RF noise Examples include microwa
10. for additional information Ensure that the wireless client is associated and joined with the correct Access Point To check this connection Windows XP follow the steps below e Click on Start gt Control Panel gt Network Connection e Right click on the Wireless Network connection 49 Select View Available Wireless Networks in Wireless Configure The Connect to Wireless Network screen appears Ensure you have selected the correct wireless network Ensure that the IP Address of the computer is in the same range and subnet as the WBR 3800 MobilSpot The default IP Address of the WBR 3800 is 192 7 All the computers on the local area network must have a unique IP Address within the same range eg 192 168 0 All computers must also have the same subnet mask e g 255 255 255 0 Any computers that have the identical IP Address will not be visible on the network To check the IP Address assigned to the wireless adapter follow the steps below Click on Start gt Run Type in cmd and press Enter Enter ipconfig all and press Enter Enter ping 192 168 0 1 to check if you can access the WBR 3800 3 Why does my wireless connection keep dropping You may try following steps to solve Antenna Orientation Try different antenna orientations for the WBR 3800 MobilSpot Try to keep the antenna at least 6 inches away from the wall or other objects Changing the Wireless Channel Try changing the channel on the WBR 3800 to a
11. save the settings and Undo to cancel 24 Forwarding Rules This page allows you to configure the port forwarding management of the WBR 3800 Use the menu on the left to access the setting pages J BASIC SETTING FORWARDING RULES J SECURITY SETTING d ADVANCED SETTING J TOOLBOX evi Aree Forwarding Rules Special AP Virtual Server Miscellaneous Allows others to access WWW FTP and other services on your LAN Special Application This configuration allows some applications to connect and work with the NAT router Miscellaneous IP Address of DMZ Host Allows a computer to be exposed to unrestricted 2 way communication Note that this feature should be used only when needed The port forwarding feature is required because the MobilSpot s NAT Network Address Translation will block incoming traffic from the Internet to the LAN if the specific port mapping is not set up in the NAT table This is to provide a level of protection to computers on your LAN however as a result creates connectivity problems when you want to make LAN resources available on the Internet These include FTP servers network game servers or other server applications There are three ways to work around the NAT and enable LAN resources on the Internet Port Forwarding Virtual Server Port Triggering Special AP page and DMZ Host Miscellaneous page 25 Forwarding Rules gt Virtual Server Virtual Server Well know
12. HELP gt Wireless Enable Disable gt WMM Capable Enable Disable gt Channel 11 E gt Security gt RADIUS Server IP 0 0 0 0 gt RADIUS port fisi2 gt RADIUS Shared Key Save Undo wossetino 21 d WPA PSK WPA PSK2 This security is more secure compared to WEP Select which type of encryption to use either TKIP or AES and then enter the key in the Passphrase field The field needs to be between 8 and 63 characters long and can be any combination of letters and numbers ASCII Wireless Settings gt Wireless Enable Disable Enable Disable WBR 3800 gt WMM Capable gt Channel 1 gt Security WPA PSK gt Encryption Type C TKIP AES gt Passphrase e WPA WPA2 Similar to 802 1 X security but with TKIP or AES Encryption You will need a RADIUS server for authentication Please enter the details of your RADIUS server Wireless Settings HELP mm mmm gt Wireless Enable Disable gt WMM Capable Enable Disable gt SSID e aan gt Channel 11 gt Security WPA2 w gt Encryption Type C TKIP AES gt RADIUS Server IP 0 0 00 gt RADIUS port fisi2 gt RADIUS Shared Key Ir Save Undo wos setting 22 After configuring the wireless security settings on the WBR 3800 MobilSpot you will also need to configure the same settings
13. Host only Outbound Packet Filter HELP 3 Item Setting Outbound Filter E Enable gt Allow all to pass except those match the following rules 9 Deny all to pass except those match the following rules 5 Use schedule rule ALWAYSON Copyto Im ID Source IP Ports Destination IP Ports Enable Schedule Rule 0 1 0 2 EI 0 3 0 4 0 5 0 6 E 0 7 0 8 Previouspage He page Save Undo Inbound Filter MAC Level To enable the Outbound Filter tick the Enable tick box There are two types of filtering policies 1 Allow all to pass except those match the specified rules 2 Deny all to pass except those match the specified rules You can specify 8 rules for each direction inbound or outbound For each rule you can define the following e Source IP address e Source port e Destination IP address e Destination port e Protocol TCP or UDP or both e Use Schedule Rule 30 For source or destination IP address you can define a single IP address 192 168 0 1 or a range of IP addresses 192 168 0 100 192 168 0 200 An empty implies all IP addresses For source or destination port you can define a single port 80 or a range of ports 1000 1999 You also need to add prefix T or U to specify TCP or UDP protocol for example T80 U53 U20002999 No
14. III KI XII LAN IP Address The local IP address of this device LAN Netmask The Netmask of the local IP address WAN s MAC Address The WAN s MAC of this device If you want to clone the MAC address from your NIC just click the Clone MAC and Save Auto Backup Checks whether your WAN port connection is active When WAN port is disconnected it will automatically switch to 3G internet WAN Type WAN connection type of your ISP You can select a correct one from the following options a Static IP Address For connections with static IP Addresses b Dynamic IP Address For connection with Dynamic IP Addresses c Dynamc IP Address with Road Runner Session Management When using the WBR 3800 with Telstra Bigpond Cable service d PPP over Ethernet For connection with PPPoE service mostly when used with ADSL modem e L2TP For connection with L2TP service f PPTP For connection with PPTP g 3G For connection with 3G service Note All the above connection types are used with a modem or router connected to the WAN port Only 3G requires a 3G USB or CardBus modem For 3G services you may need the following information from your 3G provider e APN Enter the APN for your 3G provider Pin Code Enter the PIN code for your 3G modem Dial Number No change is usually required unless required by provider User Name Enter your 3G username Password Enter your 3G password Maximum Idle Time Enter the number of seconds witho
15. LevelOne User Manual WBR 3800 MobilSpot Portable Wireless Hotspot V1 0 0805 FCC Interference Statement This eguipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against radio interference in a commercial environment This equipment can generate use and radiate radio frequency energy and if not installed and used in accordance with the instructions in this manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures are necessary to correct the interference CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 A1 Class B CE Marking Warning Hereby Digital Data Communications declares that this Model no WBR 3800 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The CE Declaration of Conformity can be downloaded at http Awww levelone eu support php FEC EX General Public License This product incorporates open source code into the software and therefore falls under the guidelines governed by the General Public License GPL agreement Adhering to the GPL reguirements the open source c
16. Novatel MC950D HSDPA Taiwan Option ICON 225 HSDPA Taiwan Sony Ericsson MD300 HSDPA Taiwan Sierra AC881U HSDPA Taiwan Solomon S3GM 660 HSDPA Taiwan SpeedUp SU 6200 CDMA2000 1x Taiwan SpeedUp SU 8200 HSDPA Taiwan Verizon ES720 EVDO USA Vodafone E172 HSDPA Germany Vodafone EasyBox HSDPA Taiwan ZTE MF620 HSDPA Taiwan Mobile Phones CEEE Nokia Nokia E90 GPRS HSDPA 54 Germany Germany PCMCIA CardBus Interface Brand Model 3G System C Motech Eston Eston Huawei Huawei Huawei ITON530C IPWireless IPWireless Kyocera Kyocera Kyocera LightSpeed LightSpeed LightSpeed MERLIN Novatel Novatel Option Option Option Option Option Option Pantech Qualcom Sierra Sierra Sierra Sierra Sierra Sony Ericsson Vodafone Vodafone CDC 650 501P 611P E600 E620 E800A Globe Trotter IPWireless_ V1 IPWireless V3 IBurst PC card KPC650 1 9G AS EDGE 100M EDGE 100N GPRS 100S U530 U530 U740 GXxX0202 Globe Trotter Globe Trotter 3G EMEA Globe Trotter GT 3G Quad GT MAX GT Fusion PX 500 GEO201 AC595 AC775 AC875 AC880 AC881 GC83 GEO201 GT 3G CDMA2000 CDMA 1X 55 EVDO EDGE UMTS HSDPA HSDPA UMTS UMTS iBurst EVDO iBurst EDGE EDGE GPRS UMTS UMTS HSDPA HSDPA UMTS HSDPA HSDPA HSDPA HSDPA EVDO HSDPA EVDO EDGE UMTS HSUPA HSUPA EDGE HSDPA HSDPA Israel Taiwan Taiwan Australia Australia Australia Taiwan Australia Australia Taiwan Taiwan Australia Taiwan
17. Save Undo Beacon Interval Beacons are packets sent by the unit to synchronize with wireless adapters The default value is set to 100 milliseconds and the acceptable range is 1 to 1000 gt Antenna Transmit Power DTIM Interval A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages When the unit has buffered broadcast or multicast messages for associated clients it sends the next DTIM with a DTIM Interval value AP clients hear the beacons and awaken to receive the broadcast and multicast messages The default value is 3 and the acceptable range is between 1 and 65535 Wireless Mode Select whether to only allow 11g connections or mixed mode to allow both 11b and 11g connections TX Rates Depending on signal strength and the capacity of the wireless client the transmission speed operates at 5Mbps and may drop to lower rates when necessary The default setting is Auto SSID Broadcast Choose whether to broadcast this unit s SSID Turning it off will make your wireless network nearly invisible Speed Enhanced Mode This TX Burst function is only available for Ralink wireless clients to increase the speed of the wireless connection Antenna Transmit Power You can either increase or decrease the antenna transmission power The default setting is 100 17dBi 44 Tool Box This section has various tools that are available to maintain
18. Set the community of GetRequest This will act as a password e Set Community Set the community of SetRequest This will act as a password e IP 1 IP 3 2 4 Enter the IP addresses of the managed PCs The unit will send SNMP Trap messages only to the IP addresses listed e SNMP Version Please select the SNMP Version of your SNMP Management software Click on Save to save the settings or Undo to cancel 39 Advanced Setting gt Routing When you have more than one MobilSpot or router with different subnets on the network you will need to enable this function to allow the different subnets to communicate with each other Routing Table HELP Item Setting E Enable RIP RIPv1 RIPv2 ID Destination Subnet Mask Gateway Hop Enable 1 a 2 F 4 5 6 7 8 Save unao There are two types of routing supported by the WBR 3800 Dynamic Routing This method uses Routing Information Protocol RIP to enable the devices to determine the best route for each packet based on the number of hops between the source and destination Tick the Enable box to enable Dynamic Routing Use RIPv2 only if you have different subnets in your network Otherwise please select RIPv1 if you need this protocol 40 Static Routing Allows computers that are connected to the WBR 3800 to communicate with computers on other LAN segments which are connected to
19. Technical Specifications 3G Access 1 PC card Type II Slot and USB 2 0 port Standards IEEE 802 11b g IEEE 802 3 IEEE 802 3u IEEE 802 11b g Turbo Data Rate 54 48 36 24 18 12 9 and 6 Mbps per Channel Auto Fall Back Range Coverage Transmit Reception Power 18dBm Per Cell Indoors approx 35 100 meters Outdoors up to 100 300 meters of Channels 1 11 for N America FCC 1 11 for Canada DOC 1 13 Europe Except Spain and France ETSI 1 14 Japan TELEC 64bit and 128bit WEP Encryption WPA Encryption Detachable Antenna 1 8dBi Firewall IP Filtering NAT Network Address Translation with VPN Pass through MAC Filtering Supported WAN type 3G Static IP Dynamic IP PPPoE PPTP L2TP Connection Scheme Connect on Demand Auto Disconnect Auto Reconnect NAT function Class 6 One to Many Max 253 Users Virtual Server DMZ Host Config amp Management Web Based Browser Configuration SNMP DHCP Server and Client Working Environment Temperature 0 40 C Humidity 10 90 non condensing OS supported Windows 95 98 ME NT 2000 XP Vista Linux Switching 5V 8 53 3G 3 5G Modem Compatibility List USB Interface Brand 7 Model 3G System Location Tested BandLuxe C 120 HSDPA Taiwan Huawei E172 HSDPA Germany Huawei E220 HSDPA Taiwan Huawei E270 HSDPA HSDPA Singapore LightSpeed HSDPA 180C HSDPA Taiwan LightSpeed EDGE 180M EDGE Taiwan Maxon USB3 8521 HSDPA Australia Novatel ES720 EVDO USA Novatel U727 EVDO USA
20. ds 42 Advanced Setting gt Scheduling This feature allows you to define the time schedule of Virtual Server and Packet Filter rules HELP gt Schedule E Enable Rule Name Save ada New Rule To enable Scheduling tick Enable and click Save 3 Schedule Rule Setting HELP Item Setting gt Name of Rule 1 Weekday _ sStartTimennimm EndTime nim Sunday Monday JI LI Tuesday Wednesday ae Thursday Saturday EI in Every Day Save Unao Bac Then create new rules by pressing the Add New Rule button Enter the Rule s Name and set the Start and End Times for each day Then click Save to save the new rule Once defined you can use it for Virtual Server and Packet Filters by entering the rule number in the Schedule Rule fields 43 Advanced Setting gt Performance This page allows you to change the settings of advanced wireless functions J Wireless Performance Settings HELP Item Setting gt Beacon interval 100 msec range 1 1000 default 100 gt DTIM interval 3 range 1 65535 default 3 gt Wireless Mode 9 mixed mode G mode gt TX Rates Auto e gt SSID Broadcast 9 Enable Disable gt Speed Enhanced Mode Enable Disable 100 17dBm e
21. e file then click Upgrade Note Please connect to the WBR 3800 using a wired LAN connection as if the connection breaks during the update it will render the unit unworkable Also disable any anti virus or firewall program before beginning the update Tool Box gt Backup Setting You can backup your settings by clicking the Backup Setting button and save it as a bin file Once you want to restore these settings please click Firmware Upgrade button and use the bin file you saved Tool Box gt Reset to Default You can also reset the unit back to factory default settings by clicking the Reset to Default button and click OK Please wait while the unit reboots Tool Box gt Reboot To reboot the unit manually click the Reboot button and click OK 47 Tool Box gt Miscellaneous This page allows you to set up the Wake on LAN feature It allows you to power up a network device remotely To use this feature the network device must be Wake on LAN enabled and you will need to know the MAC address of the device J Miscellaneous Items HELP J item Setting gt MAC Address for Wake on LAN 00 00 00 00 00 00 Wake up Save Undo By entering the network device s MAC address and click Wake Up the WBR 3800 will send a wake up command to the network device Note This feature only works for computers connected locally to the WBR 3800 48 Troubleshooting This section provides an overview of common iss
22. f Indicates no WAN link WLAN Flashing Indicates Wireless is enabled a Indicates Wireless is disabled Off Off Off Back Panel Ports Antenna To connect the supplied antenna WAN 10 100 RJ 45 Ethernet Port to connect to a modem or router LAN 10 100 RJ 45 to connect to Ethernet network card or Hub Switch Reset To reset the WBR 3800 to factory default settings All your customized settings will be lost Power Connect to the included Power Adapter Features Automatic take over back up with 3G connection as ADSL Cable WAN failover Implementation within 3 minutes allows the network to go where wires cannot go even outside the home or office Fully compatible with the 802 11g standard to provide a wireless data transfer rate of up to 54Mbps Backwards compatible with the 802 11b standard to provide a wireless data rate of up to 11Mbps Utilizes OFDM technology Orthogonal Frequency Division Multiplexing User friendly configuration and diagnostic utilities Operates in the 2 4GHz frequency range Advanced Firewall features Supports NAT with VPN pass through providing added security MAC Filtering IP Filtering Port Scheduling DHCP server enables all networked computers to automatically receive IP addresses Web based interface for Managing and Configuring Access Control to manage users on the network Supports special applications that require multiple connections Equipped wit
23. fted to 80 You can change web server port to other port Administrator Timeout The amount of time with no activity before the user will be logged out of the web configuration pages Set to zero to disable this feature Discard PING from WAN side When enabled any host on the WAN cannot ping this MobilSpot Disable UPNP When enabled UPnP will be disabled for security reasons 35 Advanced Setting These pages allows you to configure the more advanced settings on the unit Send system log to a dedicated host or email to specific receipts Dynamic DNS To host your server on a changing IP address you have to use dynamic domain name service DDNS e Qos Gives a user the capability to control network traffic with different priority SNMP Gives a user the capability to remotely manage a computer network by polling and setting terminal values and monitoring network events Routing Ifyou have more than one routers and subnets you may want to enable routing table to allow packets to find proper routing path and allow different subnets to communicate with each other System Time Let you set up the system time of this device through NTP PC s timer or manually Scheduling You can set the scheduling rules here and select the rule number in Virtual Server and Packet Filter the functions will be active with your scheduling rules 36 Advanced Setting gt System Log The WBR 3800 MobilSpot s
24. h 2x 10 100 Ethernet ports for LAN and WAN access and a Type II PC card for both 16Bit and 32Bit Slot and USB port for 3G network connection Connects multiple computers to a Broadband either WCDMA or EVDO even HSDPA modem to share the Internet connection Note The WBR 3800 MobilSpot is designed to work with either EVDO EDGE or WCDMA UMTS even up to HSDPA 3G Modem Adapters Please refer to your service provider for detailed feature information Chapter 2 Installation Note DO NOT connect the LevelOne WBR 3800 MobilSpot to power before performing the installation steps below Step 1 Attach the antenna 1 Remove the antenna from its plastic wrapper 2 Screw the antenna in a clockwise direction to the back panel of the unit 3 Once secured position the antenna upward at its connecting joint This will ensure optimal reception Step 2 Insert your wireless 3G PC card either 16bit or 32bit into the WAN PCMCIA Card Slot or plug your 3G USB modem into the USB interface Teen D U RESET USB POWER Note The WBR 3800 MobilSpot is designed to work with either UMTS EDGE or EVDO and even HSDPA 3G modem Please refer to your service provider for detailed feature information Step 3 Insert the Ethernet cable into LAN Port on the back panel of the WBR 3800 MobilSpot and an available Ethernet port on the computer you will use to configure the unit Note The WBR 3800 MobilSpot LAN Port is
25. lications cannot work with the WBR 3800 The Special Applications feature allows some of these applications to work with this product If this fails to make an application work try setting that computer as the DMZ host instead Please refer to Forwarding Rules gt Miscellaneous section 1 Trigger The outbound port number that will be triggered by the application 2 Incoming Ports When the trigger packet is detected the inbound packets sent to the specified port numbers and are allowed to pass through the firewall The WBR 3800 also comes with predefined settings for some popular applications To use the predefined settings select your application from the list select an unused ID and then click Copy to add the predefined setting to your list Note At any given time only one PC can use each Special Application tunnel 27 Forwarding Rules gt Miscellaneous Here you can set the DMZ Demilitarized Zone Host It is a computer that does not have the MobilSpot s built in firewall applied It allows the computer to be exposed to unrestricted communication to the Internet This setting is most commonly used for Internet gaming Video conferencing Internet telephony and other special applications To enable DMZ enter the IP address of the PC and tick on Enable 3 Miscellaneous Items HELP Item Setting Enable gt IP Address of DMZ Host 192 168 0 Save Undo 28 Security Setting This sec
26. may improve signal quality Note Channel range depends on your regional regulations Please see specifications for Channel details Wireless adapters automatically scan and match the wireless settings You may also select the channel you wish to use 5 Security You may select from three levels of encryption to secure your wireless network No Encryption WEP 802 1x WPAPSK WPA WPA2PSK or WPA2 a No Encryption is the default as shown in the screen above 20 b WEP Security WEP Wired Equivalent Privacy Enabling the security can protect your data while it is transferred to the WBR 3800 Select the WEP Encryption 64bit or 128bit and enter the WEP key Please select one WEP key to be used and input 26 or 10 hexadecimal 0 1 2 8 9 A B F digits Wireless Settings HELP gt Wireless Enable Disable gt WMM Capable Enable Disable gt SSID gt Channel 1 gt Security WEP be gt WEP Encryption 6 64 bit 128 bit 1 ele d 7 gt Key2 che d gt Key3 che d gt Key4 C HEX D 5 or 13 ascii characters eg passd or thisisapasswd 10 or 26 hexadecimal characters eg 0123456789 or 01234567890123456789012345 Save undo wos setting c 802 1X To use this security feature you will need to have a RADIUS server on your network to authenticate access Please type in the details for your RADIUS server Wireless Settings
27. ment e g Telstra BigPond Some ISPs require the use of PPPoE to connect to their services PPP over Ethernet Some ISPs require the use of PPTP to connect to their services Some ISPs require the use of L2TP to connect to their services Some ISPs require the use of 3G to connect to their services gt v Note Please use the login details supplied by your broadband ISP or 3G Provider 11 7 You may change the LAN IP Address of the MobilSpot if needed The LAN IP Address is private to your internal network and cannot be seen on the Internet Setup Wizard WAN Settings Dynamic IP Address EXIT gt LAN IP Address 192 168 0 1 gt Host Name ROUTER optional gt WAN s MAC Address 00 50 18 00 00 01 Save Clone MAC lt Back WAN gt Next gt 8 This page allows you to disable the wireless function set the wireless network name SSID and change the wireless channel Click Next when finished Setup Wizard Wireless settings EXIT gt Wireless Radio Enable Disable gt Network ID SSID WBR 3800 gt Channel 11 gt Back 8 Wireless gt Sur S Next gt 12 9 Select the Wireless security method of your wireless configuration Click Next to continue Setup Wizard Wireless Security EXIT gt Security Note It is strongly recommended that you set up Wireless Security such as WEP or WPA in order to secure you
28. n services select one zl Copyto p a Use schedule rule ALWAYS ON ei aana 1 1921680 2 1921680 3 1921680 4 1921680 08 gt 5 Ir 1921680 zl E 6 zl E 12 tw 19214680 Save Undo Wy DN A virtual server is defined as a Service Port and all requests to this port will be redirected to the computer specified by the Server IP Virtual Server can work with Scheduling Rules and give user more flexibility on Access control For Detail please refer to Scheduling Rule Advanced Setting gt Schedule For example if you have an FTP server port 21 at 192 168 0 1 a Web server port 80 at 192 168 0 2 and a VPN server at 192 168 0 6 then you need to specify the following virtual server mapping table Service Port Server IP Enable 192 168 0 1 192 168 0 2 1723 192 168 0 6 Note You can only bind one IP address to a Service Port at a given time 26 Forwarding Rules gt Special AP J Special Applications HELP Popular applications Select one ip e ID Trigger Incoming Ports Enable 1 2 3 4 5 6 7 8 9 10 11 12 Save Undo Some applications reguire multiple connections like Internet games Video conferencing Internet telephony etc Because of the firewall function these app
29. ode and open source license for the source code are available for free download at http global level1 com If you would like a copy of the GPL or other open source code in this software on a physical CD medium LevelOne Digital Data Communications offers to mail this CD to you upon request for a price of US 9 99 plus the cost of shipping Table of Contents Package a a T N 1 SOV SIS MURO MA UA AA 1 Chapter 1 Introduction E 2 Front LED 0 3 Back Panel Ge NANA 4 AA T AA WA AAA AA T WAA 5 Chapter le 6 9 63 4 Advanced Set p EE 15 Basi UN EE 16 Basic Setting eege 17 Basic Setting gt DHCP E e DE 19 Basic Setting Wireles 0 a 20 Basic Setting gt Change Password 24 Forwarding EE 25 Forwarding Rules gt Virtual Server ENNEN 26 27 28 Security Setting WEE 29 Security Setting gt Packet Filters ene 30 31 Security Setting gt Domain Eiter 32 Security Setting gt URL 33 Security Setting MAC 020 10 34 Security Setting gt Miscellaneous en 35 Adya nced Setting WEE 36 Advanced Setting gt System Log 37 Advanced Setting gt Dynamic ONS 2 38 Advanced Setting n 39 Advanced Setting gt ed EE 40 Advanced Setting gt System Time EEN 42 Advanced Setting gt Scheduling Auen 43 Advanced Setting gt Performance wwwwwwmamwmammwwwwi wima waanununi mii 44 aile EEN 45 T
30. on your wireless adapter before you attempt a wireless connection Please note that not all adapters supports all the available security functions To configure WDS click on WDS Setting button 3 WDS Setting HELP Item Setting gt Wireless Bridging Disable Enable gt Remote AP MAC 1 me 7707 EU mac4 is macs sis macs SS Scaned AP s MAC Select one zl Copy to Remote AP MAC L SSID Channel MAC Address Save Undo zen WDS is used to wirelessly connect multiple Access Points to extend the range of the wireless network without using cables Please note that not all Access Points support WDS functions To enable WDS Enable Wireless Bridging Then type in the MAC addresses of other Access Points in the Remote AP MAC fields Or you can copy the ones from Scanned AP s MAC list This MobilSpot can support up to 6 remote MAC addresses Click Save to save the settings and Undo to cancel 23 Basic Setting gt Change Password This page allows you to change the WBR 3800 Web Configuration password Please type in the old password factory default password is password and then type in the new password 3 Change Password Item Setting gt Old Password 7 gt New Password gt Reconfirm If you change the password make sure you use the new password next time you log into the web configuration Click Save to
31. ool Box gt System Info E 46 Tool Box gt Firmware Upgrade wwwwwwwmwmmwwmanzuwiwu mumu zawniiii iwa wiwiaia 47 Tool Box gt Backup 0 aaa 47 Tool Box gt Reset to 47 Tool Box gt Reboot E 47 ToolBox EEN 48 Troubleshooting satina a AAA ARE EE ESA 49 Technical SPSCMICANOMS HAU 53 3G 3 5G Modem Compatibility Let 54 Default Settings IP Address 192 168 0 1 Password password Wireless Mode Enable SSID WBR 3800 Security None Package Contents Important Check your product package contents FIRST The Level One WBR 3800 MobilSpot package should contain the items listed below any of the items are missing please contact your reseller immediately Level One WBR 3800 MobilSpot Portable Wireless Hotspot 1x Antenna Rubber Pad and Sponge Power Adapter 5V 3 0A RJ 45 Cable Quick Installation Guide User Manual on CD Cradle Stand er e O Caution Using a power supply with a different voltage rating than the one included with the LevelOne WBR 3800 will cause damage and void the warranty for this product System Requirements e Acompatible either 16bit or 32bit PCMCIA or USB 3G modem card with service for 3G Broadband access Note Subject to services and service terms available from your carrier e Computers with Windows Macintosh or Linux based operating systems with an installed Ethernet adapter e Internet Explorer version 6 0 or Netscape Navigator version 7 0 and above
32. prefix indicates both TCP and UDP are defined An empty implies all port addresses Packet Filter can also work with Scheduling Rules and give users more flexibility on Access control For more detail please refer to Scheduling Rule Advanced Setting gt Scheduling Each rule can be enabled or disabled individually Inbound Filter To access the Inbound Packet Filter page click on Inbound Filter on the bottom of the page All settings on this page are similar to Outbound Filters J Inbound Packet Filter HELP gt Inbound Filter IT Enable Allow all to pass except those match the following rules Deny all to pass except those match the following rules Use schedule rule ALWAYS ON DI Copy to li x ID Source IP Ports Destination IP Ports Enable Schedule Rule fo 20 E E E II P dE 2 fo VUE E fo TE fo 0000 es fo HTH TI bP Ei Previous page Next page Save Undo Outbound Filter MAC Level 31 Security Setting gt Domain Filters The Domain Filter enables you to prevent users from accessing specific domain addresses web sites 3 Domain Filter HELP Item Setting gt Domain Filter Enable gt Log DNS Query I Enable gt Privilege IP Addresses Range 19216800 67 ID Domain Suffix Action
33. r network Please refer to page 21 10 Please review the settings and then click Apply Settings to save If there are mistakes use Back to go back and make corrections 3 Setup Wizard Summary EXIT Please confirm the information below WAN Setting WAN Type Dynamic IP Address Host Name ROUTER WAN s MAC Address 00 50 18 00 00 01 Wireless Setting Wireless Enable SSID WBR 3800 Channel 11 Security None I Do you want to proceed the network testing lt Back Summary gt Apply Settings 13 11 Once settings are saved click Finish to go back to the Status page Setup Wizard Finish EXIT Configuration is Completed Please click Finish to back to Status page Or you can click Configure Again to setup the wizard again 12 If everything is properly configured the Status page will show WAN or 3G service is online and IP s are assigned 14 Chapter 4 Advanced Setup To access the Advanced Setup click on Advanced Setup at the top of the page Remaining Lease Time Or for first time installation choose Advanced Setup and click Enter 4 Select the Operations Once in the Advanced Setup you will be presented with the following menu RA tatus rd ogo a BASIC SETTING 2 FORWARDINGRULES SECURITY SETTING ADVANCED SETTING toorsox System Status HELP en AA WAN Status Sidenote Remaining Lease Time 00 00 00 Reconfiguring
34. stead of the IP address which might change J Dynamic DNS HELP Hem Setting gt DDNS 9 Disable Enable gt Provider DynDNS org Dynamic e gt Host Name gt Username E mail gt Password Key Save Undo Before you enable Dynamic DNS you need to register an account on one of the supported Dynamic DNS providers in the list After successfully registering the account the Dynamic DNS provider would provide you with the following details e Host Name e Username Email e Password To enable Dynamic DNS click the check box next to Enable in the DDNS field and choose the respective Dynamic DNS provider Enter the required details and then click Save to save the settings or Undo to cancel 38 Advanced Setting gt SNMP SNMP Simple Network Management Protocol is designed to give users the ability to remotely manage a computer or network device J SNMP Setting HELP Item Setting gt Enable SNMP Local Remote gt Get Community gt Set Community gt IP 1 0 0 0 0 gt IP2 0 0 0 0 gt IP 3 0 0 0 0 gt IP 4 0 0 0 0 gt SNMP Version 1600 6 To enable SNMP please set the following e Enable SNMP You must check either Local or Remote or both to enable SNMP function If Local is checked this unit will respond to requests from LAN If Remote is checked the unit will respond to requests from WAN e Get Community
35. t the Setup Wizard Or you may click on Advanced Setup for advanced settings Please check Chapter 4 Please Select the Operations Advanced Setup This screen reminds youto configure until the Wizard is finished 4 The Wizard steps help you to configure the MobilSpot in 5 easy steps Press Next button to start configuration Setup Wizard Setup Wizard will guide you through a basic configuration procedure step by step gt Step 1 Setup Login Password gt Step 2 WAN Setup gt Step 3 Wireless Setup gt Step 4 Summary gt Step 5 Finish EXIT 8 10 5 This page allows you to change the MobilSpot s web configuration login password To change password enter the old password default is password then enter new password Type the new password again in the Reconfirm field then click Next Or you can just click Next to keep the default password Setup Wizard Setup Login Password EXIT gt New Password gt Reconfirm It is recommended that you change the system password from the default for extra security 6 Select the type of WAN connection you want to use then click Next 3 Setup Wizard Select WAN Type EXIT ISP assigns you a static IP address Static IP Address Obtain an IP address from ISP automatically Dynamic IP Address Dynamic IP Address with Road Runner Session Manage
36. the WBR 3800 usinga different router You can specify up to eight routing rules The details below are reguired to set the routing rules P Address Subnet Mask Gateway Hop number of hops Tick Enable for each rule 41 Advanced Setting gt System Time This page allows you to set the time settings of the WBR 3800 3 System Time HELP Item 1 Setting gt Get Date and Time by NTP Protocol Time Server time nist gov X Time Zone GMT 08 00 Pacific Time US amp Canada gt Set Date and Time using PC s Date and Time Friday 21 March 2008 5 07 39 PM Set Date and Time manually gt Date Year 2002 Month Jan Day 1 Time Hour 0 0 23 Minute 0 0 59 Second 0 0 59 gt Daylight Saving Enable Disable Start Jan v oe End Jan e a There are three ways to set up the System Time of the WBR 3800 1 Get Date and Time by NTP Protocol Selected if you want to get the Date and Time from an NTP server A Time Server and time zone is required Once entered click Sync Now to sync the time with the Time Server 2 Set Date and Time using PC s Date and Time Set the Date and Time using the settings from your computer 3 Set Date and Time manually Selected if you want to Set Date and Time manually If required set the Daylight Saving settings by selecting Enable and define the Start and End dates for daylight savings perio
37. the WBR 3800 s systems View the system logs Firmware Upgrade Prompt the administrator for a file and upgrade it to this device Backup Setting Save the settings of this device to a file Reset to Default Reset the settings of this device to the default values Reboot this device 45 Tool Box gt System Info This page shows the user the System Log and Routing Table of the WBR 3800 I System Infomation Routing Table Nov 30 00 00 12 30 00 00 12 syslogd syslogd started Nov 30 00 00 12 boot Machine restarting Nov 30 00 00 12 boot LAN MAC address 00 50 18 21 c4 f9 Nov 30 00 00 12 boot WAN MAC address 00 50 18 21 c4 fa Nov 30 00 00 16 dhcpd Listening on LAN 192 168 123 0 Ea 30 00 00 29 dhcpd already acking lease 192 168 123 50 Nov3000 00 29 30 00 00 29 dhcpd offer 192 168 123 50 to 00 18 de 8a 6a 9c Nov 30 00 01 18 httpd 192 168 123 50 logins successful mewan E inform from 192 168 123 50 46 Tool Box gt Firmware Upgrade This page allows you to perform updates to the firmware of the WBR 3800 3 Firmware Upgrade Firmware Filename Browse Current firmware version is Beta 260214 The upgrade procedure takes about 140 seconds Note Do not power off the unit when itis being upgraded When the upgrade is done successfully the unit will be restarted automatically Upgrade Cancel To use click Browse and locate the firmware imag
38. tion allows you to configure the security management of the unit Click on the menu on the left to access the respective setting page Packet Filters Allows you to control access to a network by analyzing the incoming and outgoing packets and letting them pass or halting them based on the IP address of the source and destination Domain Filters Let you prevent users under this device from accessing specific Domani names URL Blocking Let you prevent users under this device from accessing specific URL strings MAC Address Control MAC Address Control allows you to assign different access right for different users and to assign a specific IP address to a certain MAC address Miscellaneous Remote Administrator Host In general only Intranet user can browse the built in web pages to perform administration task This feature enables you to perform administration task from remote host Administrator Time out The amount of time of inactivity before the device will automatically close the Administrator session Set this to zero to disable it Discard PING from WAN side When this feature is enabled hosts on the WAN cannot ping the Device 29 Security Setting gt Packet Filters Packet Filters allows you to control what packets are allowed to pass through the MobilSpot The Outbound Filter applies to all outbound packets and the Inbound Filter only applies to packets that are destined to Virtual Servers or the DMZ
39. ues and possible solutions for the installation and operation of the WBR 3800 MobilSpot 1 Unable to access the Configuration Menu when use my computer to configure the MobilSpot Why Note It is recommended that you use an Ethernet connection to configure the WBR 3800 Ensure that the Ethernet LED on the WBR 3800 MobilSpot is ON If the LED is NOT ON check to see if the cable for the Ethernet connection is securely connected Note Ensure that the IP Address of the computer is in the same range and subnet as the WBR 3800 MobilSpot The default IP Address of the WBR 3800 is 192 168 0 1 All the computers on the local area network must have a unique IP Address within the same range e g 192 168 0 x All computers must also have the same subnet mask e g 255 255 255 0 Any computers that have the identical IP Address will not be visible on the network Do a Ping test to make sure that the WBR 3800 is responding e Click on Start gt Run e Type cmd e Press Enter gt Type ping 192 168 0 1 A successful ping shows four replies Note If you have changed the default IP Address ensure you ping the correct IP Address assigned to the WBR 3800 MobilSpot Why my wireless client can NOT access the Internet When the WBR 3800 is configured to use either WEP or WPA PSK encryption ensure encryption settings match that of your wireless adapter settings Please refer to your wireless adapter documentation
40. upports both Syslog using UDP packets and E Mail alert System Log HELP Item Setting Enable gt IP Address for System Log 192 168 0 Ir O gt E mail Alert gt SMTP Server IP and Port gt Send E mail alert to gt E mail Subject View Log Send Mail Now Save Undo For Syslog you will need to enter the IP address of the host computer that will be receiving the syslog messages and tick on Enable For E Mail alert you will need to define the following E Mail Alert Tick Enable to enable this feature e SMTP Server IP and Port Enter the IP address and port of the SMTP server separated by no quotes If you do not specify the port number the default value of 25 will be used e Sent E Mail Alert to Enter the e mail addresses of the recipients for the email logs To assign more than one recipient use or no quotes to separate the e mail addresses e E Mail Subject Enter the subject for the e mail optional 37 Advanced Setting gt Dynamic DNS Dynamic DNS is a feature that allows users to set up a static domain name even when they have a dynamic internet IP address So even if your IP address changes every time you connect to your ISP the IP address can be mapped to a host name so that anyone who wants to connect to the MobilSpot or any services behind the MobilSpot from the internet can just use the Dynamic DNS hostname in
41. ut any activity before your connection will be terminated automatically Auto Reconnect When disconnected the MobilSpot will attempt to automatically reconnect to the ISP Primary DNS Secondary DNS To assign DNS Servers optional Primary WINS Secondary WINS To assign WINS Servers optional Maximum idle Time If no Internet activity for the set period then the Internet connection will be dropped Auto Reconnect When Internet connection is dropped the MobilSpot will attempt to reconnect Virtual Computer Used when WAN is set as DHCP or Static IP the user can assign a global IP address to a LAN IP address 18 Basic Setting gt DHCP Setup This page allows you to configure the DHCP server on the MobilSpot 3 DHCP Server HELP Item Setting gt DHCP Server Disable Enable gt Lease Time 1440 Minutes gt IP Pool Starting Address en gt IP Pool Ending Address bas gt Domain Name gt Primary DNS bann gt Secondary DNS bung gt Primary WINS Server bann gt Secondary WINS Server bann gt Gateway 0 0 0 0 optional Save Unao Clients List Fixed Mapping For more settings click on More DHCP Server To either Disable or Enable DHCP Server Lease Time DHCP lease time to the DHCP client IP Pool Starting Ending Address The pool of IP s that can be allocated to clients Domain Name To assign a Domain Name optional
42. ves monitors electric motors etc just do not remember my encryption key What should I do If you forgot your encryption key the Wireless client will be unable to establish a connection To reset the encryption key log into the WBR 3800 using a wired Ethernet connection Refer to Basic gt Wireless on page 21 for more information 51 6 How do I reset my WBR 3800 MobilSpot to its factory default settings If other troubleshooting methods have failed you may choose to Reset the MobilSpot to its factory default settings To hard reset the MobilSpot to its factory default settings follow the steps listed below e Ensure the MobilSpot is powered on for at least 20 seconds e Use apaper clip or pencil tip to press the reset button for ten seconds and then release e Do not power off the unit while it is rebooting e Once rebooted the default settings will be restored e Remember to access the web configuration page using default IP of 192 168 0 1 and password password 7 What is VPN VPN stands for Virtual Private Networking VPNs create a tunnel through an existing Internet connection using PPTP Point to Point Tunneling Protocol or IPSec IP Security protocols with various encryption schemes including Microsoft Challenge Handshake Authentication Protocol MSCHAP This feature allows you to use your existing Internet connection to connect to a remote site with added security 52
Download Pdf Manuals
Related Search