DT-8894 User Manual
Contents
1. User s Manual Features CFM CMM Thermo Anemometer IR Thermometer Large display of Airflow or Air Velocity plus model with built in Infrared Thermometer CFM CMM Thermo Anemometer with built in non contact IR Thermometer measures remote surface temperatures to 932 F 500 C with 30 1 distance to spot ratio and Laser Pointer Simultaneous display of Air Flow or Air Velocity plus Ambient Temperature Up to 8 easy to set dimensions ft or cm are stored in the meter s internal memory 20 point average for Air Flow and Air velocity Super large LCD Backlit Display 3 velocity accuracy via low friction 2 83 D 72mm ball bearing vane wheel on 3 9ft 120cm cable Data hold and Max Min Can set Auto Power off or not Complete with vane sensor with 3 9ft 120cm cable 9V battery and protective rubber holster Applications HVAC installation repair diagnostics and optimization Fume hood testing installation and verification Ventilation system installation servicing and analysis Environmental wind and temperature testing analysis Boiler rooms lonizer flow output monitoring Automobile aerodynamic testing Plant Fancilities Maintenance Specifications Air Velocity Range Resolution Accuracy m s 0 40 30 00 0 01 3 0 20 m s ft min 80 5900 1 3 40 ft min km h 1 4 108 0 0 1 3 0 8 km h MPH 0 9 67 0 0 1 3 0 4 MPH Kn2. e surface strike your eye Do not allow the laser light beam impinge on any gas which can explode
3. n AREA mode UNITS Press to select the mode of operation In FLOW mode the meter display air volume In VELOCITY mode the meter display air speed This button also functions as the UP scroll button in AREA mode AVG Used to obtain Average for multi point in FLOW mode or VELOCITY mode Up to 20 points can be averaged Refer to the Operation section of this manual for more details AREA Press and Hold to enter into the AREA mode ft or m in CFM ft min or CMM m min mode When recording MAX MIN AVG readings for single point press to clear former recordings HOLD Press to freeze the displayed reading Press again to unlock diplay X Press to turn the backlight on Press again to turn off MAX MIN TEMPERATURE Used to record and store the highest lowest readings for probe temperature Refer to the Operation section of this manual for more details HOLD TEMPERATURE Press to freeze the displayed reading for probe temperature Press again to unlock display Operation A MEASURING AIR VELOCITY AND AIR FLOW SINGLE POINT 1 Press the POWER button and turn meter on Meter will show full display when first power on 2 Unit is ready for use when LCD display shows VEL or FLOW on the middle and temperature in upper left corner B Continuous Moving Average The meters displays continuous moving avgerage for up to 10 hours 1 Power uint on 2 Place sensor in front of air flow source 3 Press MAX MIN key and unit begin to dis
4. ots 0 8 58 0 0 1 3 0 4 knots Air Flow Range Resolution Area CFM 0 999900 0 001 0 999 9 ft CMM 0 999900 0 001 0 999 9 m Air Temperature Range Resolution Accuracy 14 140 F 10 60 C 0 1 F C 4 0 F 2 0 C InfraRed Range Resolution Accuracy Temperature 58 to 4 F 50 to 20 0 1F C 9 0 F 5 0 C C 4 t0932 F A to500 0 1 F C 2 reading or 4 F 2 C CFM ft min Air Velocity ft min lt Area ft CMM m min Air Velocity m s lt Area m gt lt 60 CFM cubic feet per minute CMM cubic meters per minute m s ft min km h MPH knot 1 m s 1 196 87 3 60 2 24 1 944 1 ft min 0 00508 1 0 01829 0 01138 0 00987 1 km h 0 2778 54 69 1 0 6222 0 54 1 MPH 0 4464 87 89 1 6071 1 0 8679 1 knot 0 5144 101 27 1 8519 1 1523 1 Meter Description 1 LCD display for Air Velocity Air Folw Probe Temperature and Remote surface Temperature Units of measurement and user alerts are also displayed on the LCD 2 Vane sensor Hold the sensor in the flow of air to initiate a reading 3 Protective rubber holster must be removed to access to the rear battery compartment 4 Keypad see blow Press to turn the meter ON or OFF IR Laser Pointer Press and Hold to measure remote surface temperature MAX MIN Press to record and store the highest lowest and continuous moving average readings for single point Refer to the Operation section of this manual for more details This button also fuctions as the LEFT scroll button i
5. play moving average the meter will record the reading every second C MAX MIN AVG READING ON A SINGLE POINT 4 To obtain MAX MIN AVG readings on a single point 1 Power uint on 2 Place sensor in front of air flow source 3 Press MAX MIN AVG KEY The uint will begin to record readings 4 Press HOLD prior to moving instrument away from air flow source to stroe reading 5 To clear the current MAX MIN AND AVG readings press and hold MAX MIN key until unit beeps twice then release AIR VELOCITY AVERAGE FOR MULTI POINTS UP TO 20 POINTS Power unit on Hold AVG key until unit beeps twice then release the 0 will display at upper right corner and AVG will display at lower right corner Place sensor in front of air flow source As soon as the first measurement is completed press the AVG button you will hear a single beep and then release the display will show a HOLD and a AVG under the reading The reading is now being moved to internal memory And the unit will display the average reading and number of points measured The average reading is held for about 3 seconds Repeat steps 4 until all desired points have been measured This unit can record up to 20 points at one time In AVG mode press and hold AVG button for about 3 sec to return And press AREA button to clear memory of multi point average reading The meter is now ready to measure air flow average for multipoints E AREA SET 1 Power
6. unit on 2 Press UNITS key and selece CFM or CMM 3 Hold AREA key until unit beeps twice the AREA will display and enter area set mode 4 Press the MAX MIN key to shift the radix point 5 Press the HOLD key to shift the flash position 6 Press the UINTS key to adjust digit which is flash F TO OBTAIN ROMOTE SURFACE TEMPERATURE USING INFRARED THERMOMETER Press and Hold IR Laser Pointer button to measure romote surface temperature In this way LCD display will show temperature reading of surface where Laser being point Once you release the button the displayed reading will rerurn to current air folw in 6 seconds but the MAX MIN and HOLD ON G DISABLE AUTO POWER OFF The unit will turn off automatically after 15 minutes When you turn the meter on and press the y button at the same time the automatic power off feature will be disabled Note that when the meter is in the CFM CMM or Average mode automatic power off feature is disabled H BATTERY REPLACEMENT When appears on the LCD the 9V battery must be replaced Remove the meter s rubber protective jacket use a flat blade screwdriver to open the rear battery compartment and replace the 9V battery Finally close the battery compartment and replace the jacket Safety Use extreme caution when the laser beam is turn on do not let the beam enter your eye another person s eye or the eye of an animal Be careful no to let the beam on a reflectiv
Download Pdf Manuals
Related Search