IQ/OQ Protocol
Contents
1. 10 00 Protocol Installation Oualification Operation Oualification SteamScrubber amp FlaskScrubber Laboratory Glassware Washers Labconco No 1058700 Rev B Protecting your VA laboratory enulronment For more information please contact us E mail sales expotechusa com Website www ExpotechUSA com Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B Purpose and Scope IQ and OQ This Qualification Protocol is solely intended to be used with Labconco FlaskScrubber and SteamScrubber Laboratory Glassware Washers which are new or relocated Models SteamScrubbers 4400000 4400300 4400400 4400001 4400301 4400401 4400010 4400310 4400410 4400011 4400311 4400411 FlaskScrubbers 4420000 4420300 4420400 4420001 4420301 4420401 4420010 4420310 4420410 4420011 4420311 4420411 It is written to assist the end user in validation of predetermined specifications The protocol begins with planning the site for the piece of equipment and therefore is of value prior to receipt of delivery The use of this document does not replace the need for the Glassware Washer User s Manual 4503600 Information within the User s Manual is required to complete this IQ OQ Protocol Responsibilities End User The ultimate user or otherwise appointed personnel in the lab is responsible to ensure the Glassware Washer is installed and operating pr2. Open the washer door and measure the water temperature Is the temperature greater than the tap water temperature measured earlier step 2g Close the door and allow the cycle to continue into the RINSE cycle 20 Pure Water Verify the flow rate of purified water is Y N Flow Rate adequate by noting the time it takes for the purified water fill The DI Pump should be heard to run from outside the washer Did the purified water complete filling in less than 4 minutes The cycle can be CANCEL d after this test Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B B Operational Qualification Step Description Specification or Acceptance Criteria Result YES NO 1 Accessories la Racks Types The best results often depend upon the washer of Glassware being eguipped with the proper accessories Refer to Appendix D in the User s Manual Y N Are the appropriate racks and baskets available for the type of glassware to be washed The position of the upper rack can be adjusted Y N or the rack removed Has the optimal upper rack position been selected Has the upper wash arm in the SteamScrubber Y N models been height adjusted to be directly under the upper rack N A Are spindles on the lower spindle rack of the Y N FlaskScrubber models arranged for your type of glassware Are the ports without spindles N A plugged Optional upper spindle rac
3. cted program 2d Documentation Has the desired factory set cycle or custom Y N cycle parameters been documented and stored 3 Personnel Training 3a User Training Have all users been properly trained on the operation and limitations of the washer Do all users understand Which programs and racks are to be used Proper way to load each type of glassware How and when to fill detergent and neutralizing acid dispensers Y N How to start and interrupt cycles Where washer manual and procedures are kept Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B C Summary Labconco FlaskScrubber amp SteamScrubber Washer IQ OQ Protocol 1058700 Revision B Instrument Location Serial No Model No User Protocol Revision or Date published ____ Contact print name Title Review the Response columns for answers of NO Use the area below to describe the deficiency or unacceptable results Those deficiencies are to be followed with an instruction for Corrective Actions Once acceptable results are obtained the deficiency is accepted by initialing the Corrective Action Step Deficiency followed by Corrective Action Initial For more information please contact us E mail sales expotechusa com Website www ExpotechUSA com
4. d been Y N considered in the planning Refer to Appendix C of User s Manual ld Electrical Refer to the User s Manual for a list of model Y N Service numbers and their corresponding electrical requirements Are services available for the washer to be connected to a dedicated circuit of adequate size and proper voltage le Delivery If the washer has not been delivered have Y N Requirements arrangements been made with the facility or delivery agent to have equipment capable of gently handling a packaged skid of this size and weight Refer to User s Manual Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B Prior to Operation 2a Damage Claims Has the washer been inspected for any signs of damage that may have occurred while in transit or within the building Keep packaging materials until inspection is complete If damaged refer to the User s Manual for information on shipping damage claims 2b Set Up Have the washer s leveling feet or casters been installed If equipped with leveling feet has the washer in its final site been leveled and does the door open and close with minimal interference to the sides of the tank N A If an undercounter model has it been secured to the underside of the countertop for stability when the door is open N A 2c Plumbing Has hot water been plumbed to the washer and checked for l
5. eaks If desired has a purified water source been plumbed Or will the purified rinse will come from a portable container 2d Drain Connection Does the drain hose have a rise in the line per the User s Manual and is it connected to the building s drain system Does the drain hose have an air gap to prevent backflow into the washer 2e Electrical Connections Has the unit been connected to a dedicated grounded circuit of appropriate size 2f Run Diagnostics Test Water Fill Refer to the User s Manual to perform this diagnostic test in the following steps With water and power to the washer connected close the detergent cup and start the diagnostic mode Does hot tap water enters the washer when display reads FIL VIA TAP Listen for water flow Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B 2g Tap Water Verify the tap water temperature entering the Y N Temperature washer is at least 120 F 49 C Water enters the washer on the center of the right side Measured with what 2h Fill Level Open the door to the washer Verify that the Y N float switch permits the washer to fill to the proper level When the fill is complete water level should cover at least the lower half of the heater at the front of the machine The heater should be partially out of the water on the left side Close and latch the door Tes
6. k too lb Detergent Has a non foaming powder or liquid detergent Y N specifically formulated for laboratory washers been procured for this application Has the detergent dispenser been filled per the Y N User s Manual lc Acid If desired is there neutralizing acid available Y N Neutralizer for use with this washer N A Optional is the neutralizing acid dispenser Y N filled and set per the User s Manual N A Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B 2 Wash Cycle 2a Selecting Refer to Appendix C in the User s Manual Program Choosing the factory set program or customizing your own program to obtain better wash results generally involves trial runs and inspection of the glassware for cleanliness Has a procedure for the selection of an optimal Y N cycle detergent and neutralizing acid been adopted 2b Cleanliness After trial runs have successful results been Y N obtained for typical wash requirements Have the preferred detergent and neutralizing acid been proven to have satisfactory results Have the brands types volumes been documented Have other brands been removed Y N from the area to avoid confusion 2c Drying The rate at which the washed items dry is a Y N function of their material mass humidity and rinse temperature If drying is important to N A your process has adequate dry time been provided in the sele
7. operly This document can assist in that validation This document cannot however anticipate every application or unique situation encountered with the installation and operation It is therefore essential that users lab managers and safety officers work together to broaden the scope of this document through careful forethought End User Employer The employer is responsible for supporting the validation through adequate resources and training The organization shall also ensure the validation process has been fully carried out prior to applying the Washer Records should be stored in a safe easily retrievable location The location of the Washer and required validation should be included in the company s quality system Installer A qualified technician should perform the installation per the User s Manual If the manual has been misplaced copies can be obtained from the manufacturer or down loaded from their website www labconco com Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B Manufacturer Labconco Corporation certified ISO 9001 is responsible to fully test each FlaskScubber and SteamScrubber prior to shipment The manufacturer must retain these records Labconco s staff of Product Service Representatives and Product Specialists can assist with information on the purchase delivery and installation Labconco is not responsible for the actual installation or validation processes Perf
8. ormance Qualification Once the washer has been checked for proper installation and operation its performance may be validated Labconco cannot recommend specific procedures to do this The performance validation should be designed to meet the specifications and accuracy required of the application In general this requires establishing acceptance criteria making several runs and testing the results with calibrated equipment and qualified personnel Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B A Installation Qualification Step Description Specification or Acceptance Criteria Result YES NO 1 Site Planning la Space Refer to Appendix B in User s Manual Has Y N Requirements adequate floor space been provided for placement of the cabinet Is there proper clearance for the washer if Y N installed undercounter N A 1b Local Codes Are there any unigue local codes with regard to Y N electrical or plumbing connections to be considered prior to installation Ic Plumbing Is there an adequate supply of hot water near Y N Requirements the proposed installation site Can the washer be connected into the building s Y N drain plumbing where proposed Have accommodations been considered for Y N connection to a purified water source N A If connecting to a purified water source will Y N there be sufficient rate and volume N A Has the heating and cooling loa
9. t will resume after a waiting period When the display FILL VIA TAP reappears press the SELECT button twice to skip past the FILL VIA DE ION test 2i Wash Pump Does the main washer pump activate when the Y N display reads PUMP ON WASH Listen for the water spray on the inside of the washer Press the SELECT button to advance the test 2j Drain Pump Does the tank drain when the display indicates Y N PUMP ON DRAIN Listen for a change in the sound of the draining water to indicate draining is complete Press the SELECT button to advance the test 2k Detergent Cup Within a minute of the display showing Y N DETERGENT CUP can the sound of the cup opening be heard Press the SELECT button to advance the test past the HEAT HIGH T STAT and HEAT LOW T STAT 2L Blower Can the dryer blower be heard when the display Y N reads BLOWER ON Press the SELECT button to advance to DONE Open the washer door to exit diagnostic mode Labconco SteamScrubber amp FlaskScrubber Washer 10 OO Protocol 1058700 Revision B 2m Run Cycle The fill level was verified earlier however the Y N Tap Water flow rate of water entering must be at least 1 25 Flow Rate gal min 4 7 L min Start the GLASS wash cycle Note the time it takes for the filling tap water to stop Is this time less than 2 5 minutes 2n Water Heater Allow the WASH cycle to continue for at least Y N 10 of the 20 minute cycle
Download Pdf Manuals
Related Search