N-E Color FX9 Manual
Contents
1. If you lack these qualifica tions do not attempt the installation yourself instead use a professional structural rigger When rigging the unit always be secured with a secondary safety attachment The installation location of the projector has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming Installation should be checked at least one time a year by a skilled person Cleaning and maintenance Installation Maintenance The operator has to make sure that the unit is operating safely and has the installations and electron ics checked by an expert every 2 years The following points have to be considered during the inspection 1 All screws used for installing the device or part of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing fixation and installation spots ceiling suspension trussing 3 The electronic power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spat and usage have to be adhered by a skilled installer and any safety problems have to be removed Note There is no serviceable parts inside the device except for the LED s Maintenance and service operations are to be carried out by authorized dealers Replacing the fuse Only replace the fuse with the same type and rating Replacing the power cable If the power ca2. or parts This warranty gives you specifie legal rights and you may also have other rights which vary from state to state MEGA Mega Lite 5718 Kenwick St San Antonio TX 78238 Ph 210 684 2600 Fax 210 855 6279 www mega lite com info mega ite com
3. 10v 220v Connection Connection V N a L 1 ej an DMX 512 Connection The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output The sockets are wired in parallel Only use a shielded twisted pair cable designed for RS 485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another DMX input DMx output 1 Shield 2 Signal J 3 Signal Caution At the last fixture the DMX signal needs to be terminated with a terminator Solder a 120 Ohm resistor between the and the signal into a 3 pin XLR plug and plug it in to the last fixture on the signal run Pre manufactured terminator plugs are available for purchase from your Mega Lite dealer HOS DMXT 5 N E Color FX9 Mode A DMX Chanel Function Description Value 1 LED Color Red LED intensity 0 255 2 LED Color Green LED Intensity 0 255 3 LED Color Blue LED Intensity 0 255 N E Color FX9 Mode P DMX Chanel Function Description Value 1 LED Color Red LED intensity 0 255 2 LED Color Green LED Intensity 0 255 3 LED Color Blue LED Intensity 0 255 4 Strobe Strobe slow to fast 0 196 Random Strobe slow to fast 197 255 No Function 0 1 Color fade Full Bar slow to fast 2 19 Color Snap Full Bar slow to fast 20 39 Random Full Bar slow to fast 40 59 Red Chase Each slow to fast 60 79 Green C
4. MEGA N E Color Fxa USER MANUAL Table of Contents Safety Information Specifications Main Power Connection DMX 512 Connection DMX Profile Main Control Menu Rigging the Fixture Cleaning amp Maintenance Parts List wooVounse Check that the unit has not been damaged during transport Read all cautions and warnings prior to operation of this equipment Protection Against Fire Fire Maintain a minimum of 1 foot distance from any type of flame Replace fuse only with the specified type and rating Do Not install the unit to close to a heat source Make sure cable are properly secured away from unit movement Maximum surface operating temperature 80 onay Protection Against Fire A Electrical Disconnect power before servicing For connection to main power supply proceed to page 5 This unit must be earthed electronically grounded Do not expose unit to rain or moisture Bows Protection Against Mechanical Hazards 1 Use safety chain when hanging unit 2 Use quality clamps or bolts when positioning unit 3 Do not open unit while it is on risk of electrical shock Mechanical Technical Information Part Numbers Fixture 4075 N E Color FXO Mechanical Specifications 21 68 DMX Connectors XLR 3 pin amp 5 pin in out Power Connections Power Con in out Thermal Maximum ambient temperature 40 C f Maximum surface temperature 60 C 4 12 Display Digita
5. ble of this device becomes damaged it has to be replaced by authorized dealers or trained professional only Should you have further questions please contact your dealer Parts List 4075FAN Replacement fan 075 FORMA Main POB card 20755 Power Supply 407505 Display 20700 Fuse Holder O7OTRLED Te Crip LED 4075KNOB Kron Set 10 Warranty Information ited Warrant Unless otherwise stated your product is covered by a one year parts and labor limited warranty Dichroic filters and glass gobos are not guarantee against breakage or scratches to coating It is the owner responsibility to furnish receipts or invoices for verification of purchase date and dealer or distributor I purchase date cannot be provided date of manufacture will be usd to determine waranty period Returning an Item Under Warranty for Repai Ie is necessary to obtain a Retum Material Authorization RMA number from your dealer or point of purchase BEFORE any units are returned for repair The manufacturer will make te final determination as 10 whether or not the units covered by warranty Lamps are covered by the lamp manufacturer s warrant Any Product unit or parts retumed to MEGA Systems Inc must be packaged in a suitable manner to ensure the protection of such Product unit or parts and such package shall be clearly and prominently marked to indicate that the package contains retumed Produet units or parts and with an RMA number Accom
6. hase Each slow to fast 80 99 6 Macro Blue Chase Each slow to fast 100 119 White Chase Each slow to fast 120 139 Macro Effect 1 140 159 Macro Effect 2 160 179 Macro Effect 3 180 199 Macro Effect 4 200 219 Macro Effect 5 220 229 Macro Effect 6 230 249 Macro Effect 7 250 255 6 Dimmer Dimmer Off to Full 0 255 N E Color FX9 Mode F DMX Chanel Function Description Value 1 LED Color Red LED intensity 0 255 8 LED Color Green LED Intensity 0 255 3 LED Color Blue LED Intensity 0 255 25 LED Color Red LED intensity 0 255 26 LED Color Green LED Intensity 0255 27 LED Color Blue LED Intensity 0 255 N E Color FX9 Mode L DMX Chanel Function Description Value 4 Strobe No Function og Strobe slow to fast 10 255 2 LED Color Red LED intensity 0 255 3 LED Color Green LED Intensity 0255 4 LED Color Blue LED Intensity 0255 33 Strobe No Function og Strobe slow to fast 10 255 34 LED Color Red LED intensity 0 255 35 LED Color Green LED Intensity 0255 36 LED Color Blue LED Intensity 0255 Main Control Menu The control board on the fixture base is your interface to access and control CONTROL BOARD all the functions on the unit Its digital display gives you a code view of the a options and functions The following will explain each function and its options Cc eocee Gad kn k
7. l Fastening System Mounting Yoke Fixture Packaged for Shipping Size 70x 21 680x 5 250 Size 256x 5 5 x 7 750 7 Weight 7 01 Weight 7 510 te 4 86 Electrical Specifications 525 LED Quantity 9x TF Color Red s Green 9 Blue s ux LED watts 3 Tux LED refresh rate 4 7k HZ flicker free RGB 890 380 95 LUX LED Lifetime 60 000 to 100 000 hours a LED Angle 25 je Power Consumption Universal 100 240V 50 60 Hz pm Ballast Electronic 1 1 15 25 araar iry Control amp Programming Protocol DMX 512 DMX Channels 4 Modes ot operation Mode A 3 Channel RGB Mode P 6 Channel RIGB Strobe Macro Dimmer Mode F 27 Chamel FGB x9 Mode L 36 Channel Strobe AGE x 9 Operating mode Stand alone Main Power Connection Caution 1 Do not connect fixture to a dimmer system 2 This unit has Auto switching power supply It will respond to 110V or 240V automatically 3 This unit must be earthed electronically grounded 4 Replace fuse only with the specified type and rating The occupation of the connection cable is as follows This fixture is equipped with an electronic power supply that will let the unit operate from 100V to 220V from 50Hz to BOHz Cable USA Cable EU Pin 110v 220v Black Brown Live L L White Light Blue Neutral N L Green Yellow Green Ground Q 1
8. on the whole module from one color to another Press Enter use the up down keys to select desired fade speed settings Press Enter to confirm the settings 15 Steps II Flash Scroll This function allows you to change the LED s on the whole module from one color to another Press Enter use the up down keys to select desired color change speed settings Press Enter to confirm the settings 15 Steps LEES renee em Oo Chase Effect This function allows you to select different chase patterns on the whole module Press Enter use the up down keys to select desired chase settings Press Enter to confirm the settings Chase Speed This function allows you to select the speed of the chase that was selected on the Chase Effect Press Enter use the up down keys to select desired chase speed settings Press Enter to confirm the settings Rigging the fixture Caution 1 The installations must be carried out by an authorized dealer or trained professional 2 Unit may cause severe injures if you have doubts concerning the safety do not install 3 Unit is to be 24inches away from flammable materials decoration material 4 Use high quality installation equipment to hang unit When rigging a unit it is very important that you follow common safety procedures Rigging requires extensive experience includ ing but not limited to calculating working loads material being used and periodic safety inspections
9. pany all returned Product units or panis with a writen explanation of the alleged problem or malfunction Ship retumed Prod uct units or parts to 711 Kemwick St San Antonio TX 78254 USA Note Freight Damage Claims are invalid for fixtures shipped in non factory boxes and packing materials Freight All shipping will be paid by the purchaser ems under warranty shall have return shipping paid by the manufacturer only in the Continental United States Under no circumstances will freight collect shipments be accepted Prepaid shipping does not include rush expediting such as air freight Ait freight can be sent customer collect in the Continental United States REPAIR OR REPLACEMENT AS PROVIDED FOR UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER MEGA SYSTEMS INC MAKES NO WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO ANY PRODUCT AND MEGA SYS TEMS SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MEG SYSTEMS SHALL NOT BE LIABLE FOR ANY INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGE INCLUDING LOST PROF TTS SUSTAINED OR INCURRED IN CONNECTION WITH ANY PRODUCT OR CAUSED BY PRODUCT DEFECTS OR THE PARTIAL OR TOTAL FAILURE OF ANY PRODUCT REGARDLESS OF THE FORM OF ACTION WHETHER IN CONTRACT TORT INCLUDING NEGLIGENCE STRICT LIABILITY OR OTHERWISE AND WHETHER OR NOT SUCH DAMAGE WAS FORESEEN OR UNFORESEEN Warranty is void if the product is misused damaged modified in any way or for unauthorized repairs
10. t SL fb EL 85 Fae PSE EE E oe PETES FILLIT DMX Address Press Enter to select Use the up down keys to select the required DMX start channel Press Enter to confirm al eae rm Channel Mode FAI vea posmas This function allows you to select the operating mode M of the DMX channel profile Press Enter use the up u down keys to select desired Mode settings Press Enter to confirm the settings T Mode P 6 Channels RGB Strobe Macro Dimmer Mode F 27 Channels AGB x9 Mode L 38 Channels Strobe REx I Red Dimmer This function allows you to dim the red LED s on the whole module Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings 15 Steps Green Dimmer This function allows you to dim the green LED s on the whole module Press Enter use the up down keys to select desired dim mer settings Press Enter to confirm the settings 15 Steps 1 Blue Dimmer This function allows you to dim the blue LED s on the whole module Press Enter use the up down keys to select desired dimmer settings Press Enter to confirm the settings 15 Steps I iL Z Flash This function allows you to strobe the LED s on the whole module in White color Press Enter use the up down keys to select desired flash settings Press Enter to confirm the settings Pal ies CIOS Fade Scroll This function allows you to fade the LED s
Download Pdf Manuals
Related Search