instruction manual
Contents
1. 3 Setthe Auto Iris selector Figure 1 Switch 1 to Al 4 Setthe Auto Iris lens selector to DD for direct drive lenses 5 Adjust the back focus using the back focus mounting ring on the front of the camera See Section 2 13 6 With typical scene illumination set the DD Lens Level adjustment potentiometer 3 figure 1 lens iris for the correct exposure This can be achieved either visually or by using an oscilloscope to set the output of the camera to 1 V peak peak Rev A 11 HMMUO00919 02 17 04 3 4 INSTALLING VIDEO DRIVE LENSES 1 Turn the back focus adjustment ring fully clockwise when viewed from the front see Back Focus Adjustment 2 Fitthe lens to the camera and connect it according to the diagram below Pin 3 WARNING The maximum load for this type of lens must not exceed 50mA 3 Set the Auto Iris selector Figure 1 Switch 1 to Al 4 Setthe Auto lris lens selector switch to Video for video auto iris lenses 5 Adjust the back focus using the back focus mounting ring on the front of the camera See Section 2 13 6 With typical scene illumination set the Lens Level adjustment potentiometer for the correct exposure This can be done visually More accurate results will be achieved using a video level meter or oscilloscope to set the output of the camera to 1V peak peak 7 Ifthe scene lighting conditions are extremely uneven it may be necessary to adjust the2. 4 4 VIDEO IRIS 1 Verify that Auto iris lens selector switch is set to Al Increase level on lens Check wiring connections Try lens on another camera or known good lens on camera 45 DARK PICTURE 1 Check lens iris 2 Check coax termination is 75Ohm 4 6 PICTURE NOISE GRAINY DURING DAYLIGHT OPERATION Verify lens iris level with AGC function disabled 47 PICTURE TOO BRIGHT e Manual IRIS Switch electronic iris ON e DCIRIS Switch electronic iris OFF reduce DC level e Video IRIS Switch electronic iris OFF reduce level on lens Rev A 16 HMMUO00919 02 17 04 4 8 PICTURE NOT SHARP OUT OF FOCUS 1 Adjust focus on lens 2 Adjust back focus 4 9 PICTURE GOES SOFT OUT OF FOCUS IN LOW LIGHT Adjust focus under low light conditions or use a neutral density filter under normal lighting conditions Rev A 17 HMMUO00919 02 17 04 5 Rev 18 HMMUO00919 02 17 04 SECTION 5 SERVICE AND SUPPORT 5 1 SERVICE AND SUPPORT Refer servicing to qualified personnel or contact the Technical Support at 1 800 796 CCTV for assistance Rev A 19 HMMUO00919 02 17 04 5 2 LIMITED WARRANTY Honeywell International Inc Seller 1305 Waters Ridge Drive Lewisville TX 75057 warrants this camera to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for a period of up to two 3 vears from the date of manufacture Seller s obli
3. lens s Peak Average potentiometer Refer to the lens instructions Rev A 12 HMMUO00919 02 17 04 3 5 CAMERA MOUNTING Mounting points are provided on the top and bottom of the camera and are used to mount the camera on a bracket or tripod They are designed to accept standard photographic mounting bolts 1 4 BSW or 20 UNC The mounting bracket must be capable of supporting the weight of the camera and its lens In cases where the lens is substantially heavier than the camera it is better to use the mounting point on the lens itself NOTE Some installation codes dictate that the mounting bracket must be capable of supporting up to four times the combined weight of the camera and lens The mounting bracket is not evaluated by UL Rev 13 HMMUO00919 02 17 04 5 Rev 14 HMMUO00919 02 17 04 SECTION 4 TROUBLESHOOTING 4 1 NO POWER LED NOT LIT 1 Check power connections 2 Verify that the power supply is working Use a camera that is known to be good 42 NO VIDEO 1 Check Power see above 2 Check BNC connections Use a camera that is known to be good 3 Check Lens Remove lens if video present lens is source of problem 4 3 POWER BUT PICTURE IS BLACK 1 DC Iris Check Auto iris lens selector switch is set to DC 2 Increase DC level 3 Check wiring connections 4 Manual Iris Check to make sure that iris is not closed Rev A 15 HMMUO00919 02 17 04
4. level of scene illumination is low For most applications AGC HI should be selected BACKLIGHT COMPENSATION If a strong background light such as a window exists in a scene the camera will try to compensate for it by reducing the overall exposure This would mean that areas surrounding the window would become too dark Backlight compensation BLC can be set to ON to eliminate the effect of an area of strong background lighting scene The default setting is OFF BLC will only function with a manual iris lens when the Electronic Iris feature is switched on For direct drive and video drive lenses BLC will function even though the Electronic Iris feature is switched off SYNCHRONIZATION SELECTION LL INT This switch is used to select the synchronization mode of the camera When the camera is connected to an AC supply the Line lock LL mode can be used to lock the camera s frame rate to the mains frequency so that each camera in the system is triggered at the same point on the supply s AC cycle See also Line Lock Phase Adjustment Potentiometer The default setting is INT Rev 4 HMMUO00919 02 17 04 2 7 2 8 2 9 LINE LOCK PHASE ADJUSTMENT POTENTIOMETER When the camera is in line lock mode it is possible to adjust the point on the AC cycle at which the camera triggers This facility is provided so that cameras that are connected to different mains phases may still be synchronized The line lock phas
5. with Digital Signal Processing DSP e NTSC Scanning System e 480 TV Lines Resolution HCC484E 330 TV Lines Resolution HCC334E e Low Light Performance HCC484E 0 55 lux f1 2 HCC334E 0 66 lux f1 2 e Automatic Backlight Compensation BLC e Automatic Electronic Shutter AES e 12VDC 24VAC with line lock C CS Lens Mount e Supports DD or Video Drive Auto Iris Lenses e Phase Adjustable Line Lock Rev A 1 HMMUO00919 02 17 04 1 3 PACKAGE CONTENTS 1 Camera 2 Dust Cover 3 User Manual Rev A 2 HMMUO00919 02 17 04 2 1 2 2 2 3 SECTION 2 CAMERA SETTINGS CAMERA BACK A A VIDEO OUT AES RISK OF ELECTRIC SOC D D DO KOT OPEN ON HIGH AGC Default switch positions are shown Figure 1 Camera Back Al AES MODEL SELECTOR The Electronic Iris El feature compensates for excessive light levels by automatically adjusting the shutter speed of the camera Select ON or OFF default AUTO IRIS LENS TYPE SELECTOR VIDEO DRIVE OR DIRECT DC DRIVE Automatic iris lenses direct drive DC or video drive types are connected to the camera via a 4 pin square socket located at the right side of the camera Use this switch on the rear of the camera to select the type of automatic iris lens connected The default setting is DD Direct or DC drive Rev A 3 HMMUO00919 02 17 04 2 4 2 5 2 6 AGC LOW AGC HI The Automatic Gain Control feature can improve picture quality when the
6. 04 5 Rev 8 HMMUO00919 02 17 04 SECTION 3 LENS INSTALLATION 3 1 INSTALLING FIXED IRIS LENSES 1 Turn the back focus adjustment ring fully clockwise when viewed from the front see Back Focus Adjustment 2 Fit the lens to the camera 3 Ifthe lens has a focusing ring fitted set it to infinity ce then adjust the back focus 4 Ensure the Electronic Iris El and Automatic Gain Control AGC features are both turned ON Rev A 9 HMMUO00919 02 17 04 3 2 INSTALLING MANUAL IRIS LENSES 1 Turn the back focus adjustment ring fully clockwise when viewed from the front 2 Fit the lens to the camera and rotate clockwise until the lens is fully screwed into the camera 3 Turn the Electronic Iris El and Automatic Gain Control AGC features ON 4 Adjust the back focus using the back focus ring on the front of the camera See Section 2 13 Rev A 10 HMMUO00919 02 17 04 3 3 INSTALLING DIRECT OR D C DRIVE LENSES 1 Turn the back focus adjustment ring fully clockwise when viewed from the front 2 Fit the lens to the camera and rotate clockwise until the lens is fully screwed into the camera If the lens is equipped with a 4 pin connector plug the connector into the terminal on the side of the camera If the lens is not equipped with the connector connect it according to the diagram below WARNING The maximum load for this type of lens must not exceed 25mA Pin 3
7. 2 www tegtrader com Via della Resistenza 53 59 1 20090 Buccinasco Milano Italy 39 02 4571791 www ademcovideo com 6554 176 Street Surrey V3S 465 1 888 289 2288 www silentwitness com Copyright 2004 Honeywell International Inc Rev A HMMUO00919 02 17 04
8. 4 TABLE OF CONTENTS CONTINUED SECTION 4 TROUBLESHOOTING eene 15 4 1 NO POWER LED NOT LIT eee 15 4 2 NO VIDEO ire ette Ei edd ideae 15 4 3 POWER BUT PICTURE IS BLACK 15 4 4 VIDEO IRIS ides tte Ri 16 4 5 DARK PICTURE ndi ehe dee ana 16 4 6 PICTURE NOISE GRAINY DURING DAYLIGHT OPERATION 16 47 2 00 16 4 8 PICTURE NOT SHARP OUT OF FOCUS eee 17 4 9 PICTURE GOES SOFT OUT OF FOCUS IN LOW LIGHT 17 SECTION 5 SERVICE AND SUPPORT 19 5 1 SERVICE AND SUPPORT 19 5 2 LIMITED 20 SECTION 6 8 n nn 21 6 1 GENERAL SPECIFICATIONS eee 21 6 2 VIDEO SPECIFICATIONS erect cree nn 22 Rev viii HMMUO00919 02 17 04 SECTION 1 INTRODUCTION 11 INTRODUCTION Honeywell s HCC484E and HCC334E color cameras are ideally suited for use in day to day surveillance applications Designed for value the HCC484E and HCC334E save time and money with easy installation and reliable performance Their off the shelf feature set is designed for high picture quality in standard applications and they require little to no adjustment once installed 1 2 FEATURES e 1 3 Color CCD
9. Honeywell HCC334E HCC484E User Manual P Li 4 N Te N At za Re tk HCMU000919 Rev 02 04 ISSUE DATE REVISIONS A February 2004 Initial Release PCN 1640 ALL RIGHTS RESERVED NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM HONEYWELL VIDEO SYSTEMS THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL RESPECTS HOWEVER HONEYWELL VIDEO SYSTEMS CANNOT ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES RESULTING FROM THE USE THEREOF THE INFORMATION CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE REVISIONS OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH CHANGES Rev A ii HMMUO00919 02 17 04 FCC COMPLIANCE STATEMENT INFORMATION TO THE USER THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE PURSUANT TO PART 15 OF THE FCC RULES THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS OPERATION OF THIS EQUIPMENT INA RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE CAUTIO
10. N arri ieri 1 1 1 INTRODUGTION iii ira 1 1 0 BEATURES eese eee ta og e P a oe obs 1 1 3 PACKAGE CONTENTS ainiin iaai 2 SECTION 2 CAMERA SETTINGS eene 3 21 CAMERA BACK iui as beatae eut et ater Bin 3 2 2 MODEL 5 3 23 AUTO IRIS LENS TYPE SELECTOR VIDEO DRIVE OR DIRECT DC DRIVE 3 2 4 AGO LOW AGC Ell interner aa 4 2 5 BACKLIGHT COMPENSATION eee 4 2 6 SYNCHRONIZATION SELECTION 4 27 LINE LOCK PHASE ADJUSTMENT POTENTIOMETER 5 2 8 DD LENS LEVEL ADJUSTMENT POTENTIOMETER 5 2 9 POWER Ice Rete ien r a 5 2 10 COMPOSITE VIDEO OUTPUT BNC CONNECTOR 6 2 11 POWER SUPPLY Gath iaie raara 6 212 LENS SELECTION in irori inet rk 6 2 13 BACK FOCUS ADJUSTMENT i 6 SECTION 3 LENS iene 9 3 1 INSTALLING FIXED IRIS LENSES 9 3 2 INSTALLING MANUAL IRIS 5 10 3 3 INSTALLING DIRECT OR D C DRIVE LENSES 11 3 4 INSTALLING VIDEO DRIVE 12 3 5 CAMERA MOUNTING eene 13 Rev A vii HMMUO00919 02 17 0
11. N CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES 003 CET APPAREIL NUMERIQUE DE LA CLASSE A EST CONFORME A LA NORME NMB 003 DU CANADA Rev A iii HMMUO00919 02 17 04 EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is AN intended to alert the user to the presence of important operating and maintenance servicing instruction in the literature accompanying the product CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Rev A iv HMMUO00919 02 17 04 WARNINGS Installation and servicing should be performed only by qualified and experienced personnel Low voltage cameras must be powered from a UL listed class 2 power supply For outdoor use an appropriate protective housing conforming to IP65 or UL50 or better must be used Main camera is not evaluated by UL A TO PREVENT FIRE OR SHOCK HAZA
12. RD DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE SAFEGUARDS This camera range is designed for use in general purpose CCTV applications and no other purpose Only operate your camera between the temperature of 10 C to 50 C 149F to 1229F Do not operate your camera outside its specified power supply range Camera must only be used in clean dry dust free environments unless housed in suitable protective housings to IP65 or better Rev A V HMMUO00919 02 17 04 ELECTROMAGNETIC COMPATIBILITY EMC This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures INTENDED PURPOSE SECURITY AND SURVEILLANCE CCTV APPLICATIONS The product must be installed and maintained in accordance with good installation practice to enable the product to function as intended and to prevent problems Refer to Honeywell Video Systems for installation guidance MANUFACTURER S DECLARATION OF CONFORMANCE The manufacturer declares that the equipment supplied with this manual is compliant with the essential protection requirements of the EMC directive 89 336 and the Low Voltage Directive LVD 73 23 EEC Conforming to the requirements of standards EN 55022 for emissions IEC801 parts 2 3 and 4 for immunity and EN 60065 for Electrical Equipment safety Rev A vi HMMUO00919 02 17 04 TABLE OF CONTENTS SECTION 1 INTRODUCTIO
13. e adjustment potentiometer allows the line lock phase trigger point to be adjusted by 1 120 Rotating the potentiometer clockwise advances the trigger point and turning it anticlockwise retards the trigger point The factory default setting is the zero crossing point If all cameras in a system are on the same mains phase then no line lock phase adjustment should be made See also Synchronization Selection LL INT DD LENS LEVEL ADJUSTMENT POTENTIOMETER The Direct Drive lens level is controlled by this potentiometer The video output signal is converted into a DC voltage by circuitry within the camera The potentiometer sets a reference voltage against which this derived DC voltage is compared If the DC voltage is less than the reference level the lens iris opening is increased If the DC voltage is greater than the reference level the lens iris opening is decreased This control loop attempts to continually match the DC voltage derived from the video signal to the reference voltage set by the potentiometer This feature allows the installer to set the required video output amplitude e g 1Vpp that the lens should strive to maintain POWER LED In normal operation the LED on the rear panel of the camera is illuminated when power is connected to the camera Rev 5 HMMUO00919 02 17 04 210 COMPOSITE VIDEO OUTPUT BNC CONNECTOR 2 11 2 12 To obtain a 1 0Vpp composite video signal connect a video coaxial cable term
14. gation shall be limited to repairing or replacing at its option free of charge for materials or labor any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Honeywell factory service For warranty service return product transportation prepaid to Honeywell Video Systems Factory Service 1305 Waters Ridge Drive Lewisville TX 75077 THERE ARE NO WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the products will in all cases provide adequate warning or protection Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring withou
15. inated with a 75 Ohm BNC connector to the BNC socket marked VIDEO OUT POWER SUPPLY The voltage required to operate the camera is clearly marked on the rear panel of the camera Connections are indicated above the terminals on the rear panel of the camera The power supply must be a UL listed class 2 type s LENS SELECTION 2 13 Suitable lens types are C and CS mount in fixed iris manual iris video auto iris or direct drive auto iris versions Cameras are factory set for CS mount lenses If using a C mount lens rotate the back focus adjustment mechanism fully clockwise when viewed from the front of the camera before fitting the lens see Back Focus Adjustment BACK FOCUS ADJUSTMENT The back focus adjustment is accessible at the front end of the camera housing to adjust the back focal length or picture focus The range of adjustment allows both C and CS mount lenses to be used without the need for a spacer ring Rev A 6 HMMUO00919 02 17 04 2 13 BACK FOCUS ADJUSTMENT CONTINUED To use the back focus mechanism 1 Unlock the back focus mechanism using the Back Focus adjustment lock figure 1 2 Rotate the back focus adjustment ring as required When viewed from the front of the camera clockwise adjustment moves the CCD sensor away from the back of the lens counter clockwise adjustment moves the CCD sensor towards the back of the lens 3 Lock the back focus mechanism Rev A 7 HMMUO00919 02 17
16. r Indicator Green LED on Rear Panel IRIS Connector 4pin Connector on Side Panasonic Standard for Video and DC Drive Lens Mount CS CMount Adjustable Back Focus Adjust CS Mount 11mm Mount 18mm Mounting Hole 1 4 Top and Bottom Rev A 21 HMMUO00919 02 17 04 6 2 VIDEO SPECIFICATIONS HCC484E HCC334E Resolution 480 TV Lines 330 TV Lines 0 55Lux F 1 2 0 66Lux F 1 2 Minimum Illumination Video S0IRE Video Output Output Video Output 1 0Vpp 750hm BNC unbalance S N Ratio 50dB AGC High Gain 36dB AGC Low Gain 30dB H Aperture 10 IRE 0 45 100IRE Video Output V Aperture 10 IRE r 0 45 100IRE Video Output Gamma Compensation 0 45 Specifications are subject to change without prior notice for product improvements Actual specifications may vary depending on features and components Rev A 22 HMMUO00919 02 17 04 Rev 23 HMMUO00919 02 17 04 Honeywell Video Systems 1305 Waters Ridge Drive Lewisville TX 75077 www honeywellvideo com Unit 5 Riverside Centre 24 28 River Road West Parramatta NSW 2150 Australia 61 2 8837 9300 www ademco com au Aston Fields Rd Whitehouse Ind Est Runcorn UK WA7 3DL 44 1928 754000 www videocontrols co uk 9315 NW 112 Avenue Miami FL 33178 USA 1 305 805 8188 www ademcoint com 53 Juta Street Braamfontein 2001 South Africa 27 11 403 300
17. t providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DIRECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS OF CAUSE OR ORIGIN SELLER S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorized Rev A 20 HMMUO00919 02 17 04 SECTION 6 SPECIFICATIONS 6 1 GENERAL SPECIFICATIONS HCC484E HCC334E Image Sensor 1 3 Format Interline CCD Sensor Pixel Elements 510 H x 492 V approx 250K pixels 768 H x 494 V approx 380K pixels Scanning Frequency NTSC 2 1 Interlace 15750Hz V 59 94Hz Operation Temperature 10 C 50 C Storage Temperature 20 C 60 C Output Terminals BNC 750hm Unbalance Input Terminals 3pin Push Lock Terminal Block Power Source 12VDC 24VAC Power Consumption 4 2W Max Powe
Download Pdf Manuals
Related Search