MPEG4 4CH DVR Quick Guide
Contents
1. 6 1 2 3 4 Press one of these buttons to show the channel display of CH1 CH4 on the monitor REC Press this button to activate manual recording PLAY Press this button to play the latest recorded video PAUSE STOP REW FF Under the playback mode Press one of these button to pause stop rewind fast forward the playback file A V lt gt Press one of these direction buttons to move the cursor up down left right Under the DVR menu mode these direction buttons can use for the following operation A V Make the selection Change the settings lt gt Make the selection 1 MENU Press this button to enter exit the DVR menu mode In the sub layer of the DVR menu press this button to confirm the settings and go back to the upper layer 8 ENTER Confirm the password entering 9 LIST Event List Search To quick search the recorded files by event list press this button to show all types of the event lists Select one of the event list and press ENTER button to playback the selected file MANUAL List the information of the manual recorded files The DVR will save one recorded file once any recording setting is changed SYSTEM List the information of the system recorded files The DVR system will save one recorded file every one hour MOTION List the information of the motion trigger recorded files TIMER List the information of the timer recorded files 10 SLOW Under the playback mode pre2. 6 LAN Connect to Internet by LAN cable 7 LINK ACT When your DVR is connected to the Internet this LED will be on 8 DC 19V Connect to the supplied adapter 3 CONNECTIONS AND SETUP 3 1 HDD Installation The HDD must be installed before the DVR is turned on Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Loose the screws on the upper cover and open the upper cover of the DVR Remove the HDD bracket Get a suitable brand HDD and set the HDD mode to Master mode Slide and fasten the HDD to the HDD bracket two screws for each side Replace the HDD bracket back to the DVR base Connect the HDD to the power connector and the IDE BUS connector make sure to align the HDD precisely for pin connection Close the upper cover of the DVR and fasten all the screws you loosened in Step 1 3 2 Camera Connection The cameras must be connected and power supplied BEFORE the DVR is turned on The DVR will automatically detect the video system of the connected camera s NTSC PAL and switch itself to the correct system Connect the camera with the indicated power supply and connect the camera video output to the DVR video input port with a coaxial cable or RCA lines with BNC connectors Note For detailed DVR video input output ports please refer to 2 2 Rear Panel at page 2 For detailed camera operation please refer to its own manual Note If you want to make a video backup with au
3. The DVR will save one recorded file once any recording setting is changed MOTION List the information of the motion trigger recorded files SYSTEM List the information of the system recorded files The DVR system will save one recorded file every one hour TIMER List the information of the timer recorded files 2 Quick Search by Time Press the MENU button to enter the menu list move the cursor to QUICK SEARCH and press ENTER button to enter the quick time search menu You can search any specific events by time Year Month Day Hour Min and directly play the file you find 3 search the Record Event by Log on the AP Software Press Miscellaneous Control button to show the miscellaneous control panel In the miscellaneous control panel press Cs Status List button to enter the Status List page In this page you can see the list of three different types of recording User Motion Alarm and press Play button to directly playback the file
4. live audio Key lock Key unlock Digital Zoom mode channel m Digital zoom A Timer recording Motion om Recording unselected 4 2 Recording When the recording and the pre alarm function are activated this device will overwrite 8GB data from the oldest for continuous recording without notice 1 Continuous Recording Icon When the DVR is properly connected with camera you can see the icon recording on the monitor 2 Motion Recording Icon When the motion alarm detection is activated once motion or external alarm happens you will see the icon Eb motion on the monitor 3 Timer Recording Icon When the timer record is activated you will see the icon timer on the monitor Note The audio source connected to the Audio 1 will be recorded with the video of the CH1 4 3 Playback Press the PLAY button on the DVR control panel and the device will playback the latest recorded video Note There must be at least 8192 images of recorded data for playback to work properly If not the device will stop playback For example if the IPS is set to 30 the recording time should be at least 205 seconds 8192 images 40 IPS for the playback to work properly 1 Fast Forward Fast Rewind You can increase the speed for fast forward and rewind on this device In the playback mode Press FF once to get 4X speed forward and press twice to get 8X speed etc And the maximum speed is 32X Pres
5. 261Z MPEG4 4CH DVR Quick Guide J F 9 _REC PLY Fo J e E e 3 s 4 gt i G4 HDD HDDFull ALARM TIMER PLAY REC 7 NS 4 a O O O O O O MN ENTER LIT SLOW zoom fH SEQ O WOA ei wal Please read instructions thoroughly before operation and retain it for future reference The image shown above may differ from the actual product appearance DR040_Quick_V1 0 1 Package Contents _ Digital video recorder DVR Thermal conductive silicone rubber Adapter and power cord _ HDD bracket screws spare parts _ Free licensed software AP disc _ DSUB PIN connector _ Manual amp quick start amp IR remote control manual AAA size battery 2 _ Vertical panel sticker for remote controller certain models only 2 FRONT AND REAR PANELS 2 1 Front Panel 1 LED Indication The following LEDs will be on when HDD HDD is reading or recording HDD Full HDD is full ALARM Any motion detection is triggered TIMER Timer recording is activated PLAY DVR is under playback mode REC DVR is under recording mode Q Power is connected Note To turn off your DVR please disconnect the power supply 2 3 4 5
6. OSD Upgrade 1 Use USB to upgrade firmware or OSD Step 1 Format the USB memory device as FAT32 format first Step 2 Get the upgrade files from your distributor and save the upgrade files in your USB flash device do not change the file name Step 3 In the SYSTEM menu move the cursor to UPGRADE and press ENTER button Step 4 Select YES and press ENTER button again to confirm upgrade 2 Use AP software to remotely upgrade firmware or OSD Step 1 Save the upgrade files at your PC do not change the file name and then login to the AP software Step 2 Press EF Miscellaneous Control button to show the miscellaneous control panel In the miscellaneous control panel press oei Tools button on the miscellaneous control panel to enter the AP upgrade window Step 3 Enter the user name password IP address and port number of the DVR Step 4 Press Firmware or Language tab as needed and press Add to select the firmware or OSD files to upgrade Step 5 Press Update Firmware or Update Language button to start the upgrade Note For remote upgrade details please refer to page 45 in your user manual 4 6 Search 1 search by List Press LIST button on the DVR control panel to show the list for all types of the recorded files Choose the list you want to view and press ENTER button to start playback MANUAL List the information of the manual recorded files
7. dio please connect audio camera to the CH1 which Support the audio function 3 3 Power Setup This device should be operated only with the type of power source indicated on the manufacturer s label Connect the indicated AC power cord to the power adapter and plug into an electrical outlet The power LED 1 will be on as green It takes approximately 10 to 15 seconds to boot the system 3 4 Date and Time Setting Before operating your DVR please set the date and time on your DVR first Press the MENU button and enter the password to go to the menu list The default admin password is 0000 Move the cursor to DATE and you can set the date time daylight saving in the DATE menu list 3 5 Password Setting Press the MENU button and enter the password to go to the menu list Then move the cursor to ADVANCE to enter the advanced setting menu In the ADVANCE menu move the cursor to SYSTEM Select PASSWORD and press the ENTER button to enter the submenu to set the password four digits The default admin password is OOOO ADVANCE SYSTEM CAMERA PASSWORD XXXX DETECTION RESET DEFAULT RESET DISPLAY CLEAR HDD HDD MASTER 1 ALERT UPGRADE START SYSTEM AUTO KEYLOCK NEVER NETWORK LANGUAGE ENGLISH BACKUP VIDEO FORMAT NTSC HDD INFO VERSION 1167 1012 1022 1017 4 BASIC OPERATION 4 1 Live Page In this live page of the DVR you can see the following icons Funetion _
8. s REW once to get 4X speed rewind and press twice to get 8X speed etc And the maximum speed is 32X Note During playback the image size of the recording CIF will be shown on the screen 2 Pause Image Jog Press PAUSE button to pause the playback In the pause mode Press gt button once to get one frame forward Press lt 1 button once to get one frame rewind 3 Stop Pressing STOP button under playback mode the screen of this device will return to live monitoring mode 4 Slow Playback Press SLOW button to get 1 4X speed playback and press twice to get 1 8X speed playback 5 Audio Playback Use these two buttons to select the live or playback sound of the audio channels ih Icon q means Live audio of the 1 audio channel Icon i means Playback audio of the 1 audio channel Note If you want to make a video backup with audio please connect audio camera to CH1 which support the audio function 4 4 Key Lock and Unlock 1 Key Lock On Press MENU ENTER buttons at the same time on the DVR control panel to lock keys Or set the time out after which the key lock function is activated Never 10 SEC 30 SEC 60 SEC Please refer to page 19 in your user manual 2 Key Lock Off Enter the DVR password to exit Key Lock mode Note For the password setting please refer to page 6 in your user manual 4 5 Upgrade Firmware Multilanguage
9. ss this button to slowly playback the recorded file by 1 4 speed or 1 8 speed 11 ZOOM In the live mode of the DVR press this button to enlarge the image of the selected channel 12 HH Quad Display Press this button to show the quad display mode on the monitor Note If you want to make a video backup with audio please connect audio camera to the CH1 which Support the audio function 13 MENU ENTER Key lock Press these two buttons at the same time to lock keys on the DVR front panel 2 2 Rear Panel 1 2 USB Port To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 first VIDEO INPUT 1 4CH Connect to video sources such as cameras Note If you want to make a video backup with audio please connect audio camera to CH1 which 3 Supports the audio function VIDEO OUTPUT Connect to a CRT monitor for video output 4 AUDIO IN 1 Connect to audio source such as camera equipped with the audio function When users start recording the audio input will also be recorded with corresponding video channel Note The audio source connected to the Audio 1 will be recorded with the video of the CH1 5 Audio OUT 1 Connect to a monitor or speaker with 1 mono audio output
Download Pdf Manuals
Related Search