DIP/SOIC/TSSOP EEPROM Board User Manual v1.00
Contents
1. an external power source can be applied to the VIN pins in the External connector J1 If a different voltage is needed it is possible to use an external power supply to provide power to the target chip To use an external power source please use a jumper to short the pins next to EXT position 3 on the VDD Source connector J2 Power should be applied to the VIN pins on the External J1 connector 4 4 SPI Slave Select 1 2 PULL SS DOWN 2 3 PULL SS UP SS CONNECT J3 J4 Figure 12 The developer can connect or disconnect Slave Select SS pin as well as configure the polarity of SS on the board 4 4 1 Connecting SS Some SPl based memory chips do not require the use of the Slave Select pin In these cases the SS pin can be disconnected To do this simply remove the jumper from the SS Connect header J3 14 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 4 4 2 SS Pull down Pull up Resistors The EEPROM Socket Board provides the ability either pull down or pull up the Slave Select line depending on the requirements of the target device by using a jumper to short pins on the J4 connector To pull SS down short pins 1 and 2 To pull SS up short pins 2 and 3 15 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 5 Legal Contact 5 1 Disclaimer All of the software and documentation provided in this datasheet is copyright Total Phase Inc Total Phase License is granted to the user to fr2. Purpose I O e Windows and Linux support TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual e Free software and royalty free API 1 5 Cheetah SPI Host Adapter The Cheetah SPI Host Adapter is a high speed SPI adapter that is capable of communicating over SPI at up to 40 MHz The Cheetah adapter is specifically designed to communicate with high speed SPl based Flash memory It is an ideal tool to develop debug and program SPl based systems Figure 4 The Cheetah SPI Host Adapter is a high speed SPI Master only adapter It is capable of signaling from 1 to 40 MHz with no inter byte delays 1 5 1 Features e SPI Master signaling up to 40 MHz e Maximum throughput with no inter byte delays e User configurable timing delays e Windows and Linux support e Free software and royalty free API TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 2 Sockets The EEPROM Socket Board offers three different sockets to interface with your memory chip DIP8 SOIC8 and TSSOP8 Please note that only one can be used at a time as they are all cross connected TSSOPS Figure 5 The EEPROM Socket Board provides three different sockets for interfacing with your stand alone memory chip 2 1 Compatible Chip Sizes The three sockets of the EEPROM Socket Board are compatible with standard sized chip packages Figure 6 provides information about the supported sizes for all the sockets Please note that all measu
3. DIP SOIC TSSOP EEPROM Socket Board DIP SOIC TSSOP EEPROM Board TOTAL 2c a VDD rasors External P H A S F SCL E SOA SPI ss Supported products SCK VDD SOURCE FC SPI r Aardvark 2 TOTAL PHASE www Dolap ase com 1 2 PULL 55 DOWN i 2 3 PULL 5 UP SS CONNECT JJ 2006 Total Phase Inc v1 00 Features EEPROM Socket Board r Manual v1 Programming of stand alone 1 C and SPl based vse ra ni EEPROM memory chips 10 e DIP 8 socket SOIC 8 socket e TSSOP 8 socket e Multiple voltage options e Multigimple SPI Slave Select options Summary The EEPROM Socket Board allows a developer to flash and burn stand alone lC or SPl based EEPROM memory chips by using either an Aardvark C SPI Host Adapter or a Cheetah SPI Host Adapter as an interface from a Windows or Linux computer The EEPROM Socket Board supports three different standard chip packages DIP8 SOIC8 and TSSOP8 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 1 Overview The EEPROM Socket Board provides embedded systems engineers with an easy and cost effective method of programming 1 C and SPl based memory devices Using Total Phase s industry leading host adapters and software engineers can take full advantage of the Flash Center programming software along with the Aardvark C SPI Host Adapter and the Cheetah SPI Host Adapter to program their Serial EEPROM memory chips 6 DIP SOIC TSSOP EEPR
4. OIC TSSOP EEPROM Board User Manual To remove a chip 1 Press down on the top of the socket to raise the contact pins 2 Carefully remove the chip using a vacuum pickup tool or equivalent tool 3 Release the top of the socket 4 2 Connecting the Pins Since different chips have different pin configurations the EEPROM Socket Boardincludes a 8 pin split ribbon cable to allow you to connect the pins to the correct sources 2c 3 VDD SCL SDA SPI ss MISO SCK MOSI GND J8 Figure 8 The Pin Board connector provides the developer with a easy way to connect the correct signals to the appropriate pins of the memory chip that is to be programmed The included 8 pin split cable can be used to connect the correct signal to the appropriate pin In the top left side of the board you will notice that there is a graphic representation of a chip with numbered pins from 1 to 8 Figure 8 Along both sides of the drawing are two 2 banks of 4 pin headers These banks are connected to the eight 8 pins of the chip in the socket The pins of the chip should be connected to the appropriate sources as described by the chip s datasheet Various sources are provided around the chip diagram Along the top of the chip are five 5 pins for VDD and along the bottom of the chip are five 5 pins for GND To the left of the chip are sources for the IC and SPI pins Each source is labeled along the left Figure 9 shows a EEPROM Socket Board th
5. OM Board 2 TSSOPS FC 48 VDD SCL SDA SPI ss MISO SCK MOSI ULL 55 DOWN 1 2P 2 3 PULL SS UP SS CONNECT J3 J4 Aardvark 1 E al 4 TOTAL PHASE 6 www totalphase com c 2006 Total Phase Inc v1 00 1 1 Features e Flash and burn I C and SPI EEPROMs that are in any of these standard chip packages DIP8 SOIC8 or TSSOP8 External J1 SCL SDA ss SCK MOSI MISO VIN VDD SOURCE Sos EXT 5y 3 3V Aardvark 2 GND GND GND GND GND GND GND GND Ej o Figure 1 Schematic of the EEPROM Socket Board e Specify 5 V 3 3 V or an external VDD Source at any voltage level e Connect or disconnect Slave Select SS and change the polarity of SS e Gang Program multiple devices by using multiple socket board and programming adapter sets in parallel on the same host computer TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 1 2 What s Included The EEPROM Socket Board comes complete with e EEPROM Socket Board e 8 pin split ribbon cable 1 3 Flash Center Software The Flash Center Software is a free software package that allows engineers to quickly erase program and verify 1 C and SPI based EEPROM and Flash memory chips that are interfaced through an Aardvark C SPI Host Adapter and or Cheetah SPI Host Adapter FLASH Genter ER re ta TOTAL PHASE Figure 2 The Flash Center Software is a free memory chip programming software 1 3 1 Features e Fast speeds t
6. at has been configured to program an I C EEPROM 12 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual Figure 9 This is the view from the top of the EEPROM Socket Board which has been configured to program an FC EEPROM which has been loaded into the TSSOP8 socket One end of the supplied 8 pin ribbon cable has been connected to the eight 8 pins of Pin Board connector around the graphic of the chip The other end has been connected to the appropriate sources as indicated by the device s datasheet 4 3 Powering the Device VDD SOURCE EXT 5V 3 3V o Figure 10 The EEPROM Socket Boardoffers two different voltage levels 5 V and 3 3 V If another voltage level is desired the develop can select EXT and attach an external power source to the board There are multiple options for powering the device to be programmed The Aardvark adapter and Cheetah adapter are both able to send downstream power to the EEPROM Socket Board which can be used to power the chip Two different voltages are available 5 V and 3 3 V To select one of these voltages simply use a jumper to short the pins next to the appropriate voltage on the VDD Source connector J2 13 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 4 3 1 External Power Source External J1 SCL GND SDA GND s GND SCK GND MOSI MISO VIN VIN External VDD SOURCE Power Source EXT 5V 3 3V a gt Figure 11 When EXT is selected
7. eely use and distribute the software and documentation in complete and unaltered form provided that the purpose is to use or evaluate Total Phase products Distribution rights do not include public posting or mirroring on Internet websites Only a link to the Total Phase download area can be provided on such public websites Total Phase shall in no event be liable to any party for direct indirect special general incidental or consequential damages arising from the use of its site the software or documentation downloaded from its site or any derivative works thereof even if Total Phase or distributors have been advised of the possibility of such damage The software its documentation and any derivative works is provided on an as is basis and thus comes with absolutely no warranty either express or implied This disclaimer includes but is not limited to implied warranties of merchantability fitness for any particular purpose and non infringement Total Phase and distributors have no obligation to provide maintenance support or updates Information in this document is subject to change without notice and should not be construed as a commitment by Total Phase While the information contained herein is believed to be accurate Total Phase assumes no responsibility for any errors and or omissions that may appear in this document 5 2 Life Support Equipment Policy Total Phase products are not authorized for use in life support devices
8. he Flash Center Software can read a typical 4 Megabyte flash memory in 0 7 seconds e Gang programming support the Flash Center Software can program multiple devices in parallel by connecting to multiple Aardvark I C SPI Host Adapters and or Cheetah SPI Host Adapters on the same computer e Extensible device support the Flash Center Software has an extensible XML based memory device library By adding or modifying the XML descriptions of target memory devices developers can instantly support almost any 1 C or SPl based EEPROM or Serial Flash memory TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 1 3 2 Minimum Requirements e Linux kernel 2 6 and above Windows XP SP2 or later Windows Vista 32 bit 64 bit Windows 7 32 bit 64 bit e One or more available High speed USB 2 0 ports One or more Aardvark lC SPI Host Adapters and or Cheetah SPI Host Adapters 1 4 Aardvark lC SPI Host Adapter The Aardvark lC SPI Host Adapteris a fast and powerful IC bus and SPI bus host adapter through USB It allows a developer to interface a Linux or Windows PC to a downstream embedded system environment and transfer serial messages using the 1 C and SPI protocols Figure 3 The Aardvark FC SPI Host Adapter is a USB to FC and SPI adapter that allows developers to interface their computers to target embedded systems 1 4 1 Features 2C Master and Slave 1 800 kHz e SPI Master up to 8 MHz and Slave up to 4 MHz e General
9. or systems Life support devices or systems include but are not limited to surgical implants medical systems and other safety critical systems in which failure of a Total Phase product could Cause personal injury or loss of life Should a Total Phase product be used in such an unauthorized manner Buyer agrees to indemnify and hold harmless Total Phase its officers employees affiliates and distributors from any and all claims arising from such use even if such claim alleges that Total Phase was negligent in the design or manufacture of its product 5 3 Contact Information Total Phase can be found on the Internet at http www totalphase com If you have support related questions please email the product engineers at support totalphase com For sales inquiries please contact sales totalphase com 16 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 2010 2008 Total Phase Inc All rights reserved 17
10. rements are in millimeters mm TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual Top View End View Side View 1 P A A T O E1 E t N p m P H s P o s D A o P Q E1 1 D D Figure 6 Diagrams of the supported package sizes Please note that the diagrams are not to scale Compatible chip sizes for each of the sockets available on the EEPROM Socket Board All measurements are in millimeters mm ns sores Tss0P6 79 600 640 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 3 Connectors 3 1 Aardvark 1 and Aardvark 2 There are the two boxed connectors at the bottom of the EEPROM Socket Board which are used to connect the board to an Aardvark l C SPI Host Adapter or a Cheetah SPI Host Adapter These two connectors are cross connected so it does not matter which one is used In most cases you will only want to connect a single adapter to the EEPROM Socket Board at a time The second connector is available to connect to a protocol analyzer or to cross connect with another adapter for testing purposes For example an Aardvark adapter or a Cheetah adapter can be connected to the board through Aardvark 1 to program the memory chip At the same time a Beagle lC SPI Protocol Analyzer can be attached to Aardvark 2 to monitor the bus while the chip is being programmed to ensure that the da
11. ta on the bus is correct 3 2 External External J1 SCL GND SDA GND ss GND SCK GND MOSI GND MISO GND VIN GND VIN GND Figure 7 The External Connector J1 provides the developer with a quick and easy way to interface or monitor any or all of the EEPROM Socket Board signals All the signals on the board are available for external monitoring through the External connector J1 The two VIN pins allow a user to use an external power source to power TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual the memory device Please refer to the Programming a Device section for more information 3 3 Powering the EEPROM Socket Board To power the EEPROM Socket Board the Cheetah or Aardvark adapter must be configured to send target power to the board This can be accomplished via the Rosetta Language Bindings the Flash Center software the Aardvark Control Center Software or the Cheetah GUI Software When powered on the board s Power LED will be lit 3 4 Cross Connecting Aardvark Adapters and or Cheetah Adapiers When cross connecting two adapters the board must be powered on Otherwise results may be unpredictable If you experience problems please make sure that the Power LED on the board is lit 10 TOTAL PHASE DIP SOIC TSSOP EEPROM Board User Manual 4 Programming a Device I C EEPROMs and SPI EEPROMs can be programmed using the Flash Center Software in conjunction with an Aardvark adapter or a Cheetah adapter De
12. tailed technical information about all these products can be found on Total Phase s website 4 1 Inserting and Removing Device To program a chip insert the chip into the appropriate socket Please note that all the sockets are cross connected so it is only possible to use one socket at a time Whenever handling chips always be sure to follow safe handling procedures to ensure that the chips are not damaged 4 1 1 DIP8 To insert a DIP8 chip simply align the pins with the socket and firmly press the chip into the socket To remove a DIP8 chip we recommend that a DIP extractor tool is used to prevent damage to the chip and its pins 4 1 2 SOIC8 and TSSOP8 Both the SOIC8 and TSSOP8 sockets are zero insertion force sockets and work on the same principle To insert a chip 1 Press down on the top of the socket to raise the contact pins 2 While pressing down on the socket carefully place the chip into the socket and make sure that the orientation of the chip is correct pin 1 should always be in the top left corner 3 Once the chip is in place release the top of the socket to allow the contact pins to drop and hold the chip in place At this point the chip should be held securely in place Please make sure that all the contact pins have made contact with the correct pins on the chip When removing the chip we recommend using a vacuum pickup tool to prevent damage to the chip and its pins 11 TOTAL PHASE DIP S
Download Pdf Manuals
Related Search