Ferm cordless impact drill 32,4 V FCD-3240-I
Contents
1. to desired setting I is low and 20 is high Insert bat tery and unlock direction switch to make drill ready for use Start at low setting and increase setting until the cor rect setting for the job is found Use the direction switch set to the right to insert screws and to the left to remove them Do not use as a screwdriver with the torque ring set in drill position this will damage the drill Use as a drill Remove battery and set direction switch in middle lock position Setthe sleeve 5 to drill setting Insert a drill bit into chuckand set the torque ring 4 to drilling position Check the direction switch is set to the correct direction normally to R for right hand operation Insert battery and unlock direction switch to make drill ready for use Use as an impact drill For drilling hard material like stone or concrete Remove battery and set direction switch in middle lock position Set the sleeve 5 to impact hammer setting Insert a suitable hard tipped masonry bit into chuck Check the direction switch is set to the correct direction normally to R for right hand operation Insert battery and unlock direction switch to make drill ready for use Ferm MAINTENCE CARE AND REPAIR CLEANING Clean by brushing witha soft brush Do not use flammable liquids to clean the drill never use solvents such as petrol ammonia or alcohol they damage the plastic parts and presenta fir2. push the tabs 8 on either side of the drill handle with finger and thumb and slide out of drill 4 Fig B OPERATION Toswitch ON OFF Make sure the direction switch 1 is set to left or right position then press the trigger switch 2 Tolocktrigger Release the trigger switch and put the direction switch 1 in the central position Speed control Adjust the drills speed by more or less pressure on the trigger switch 2 Direction of rotation Change the direction of rotation by setting the direction switch 1 to left or right this must be done when the drill isnotrotating Drill or impact setting Set sleeve 5 clockwise to drill position and anticlock wise to impact or hammer setting Ferm INSERTING AND REMOVING ACCESSORIES Remove battery and set direction switch in middle lock position Put the accessory into the chuck 3 as far as it will go then tighten firmly anticlockwise by hand only hold one section of the chuck and turn the other to tighten Remove accessories by turning the front part of the chuck clockwise while holding the other Keep your finger off the trigger switch during these operations Insert battery and unlock direction switch to make drill ready for use Use as a screwdriver Remove battery and set direction switch in middle lock position Set sleeve 5 to drill setting then insert a suitable screwdriver bit into the chuck Set the torque ring 4
3. mains supply The output voltage on the charger is suitable to use with the drill battery Thebattery voltage is suitable for the drill Note The battery supplied with the drill is not fully charged CHARGING THE BATTERY Refer to Fig A Place the battery charger 9 ona level surface check it is connected correctly and the air vents on the charger are not blocked then slide the battery 7 onto the charger Make sure the terminals on the bat tery tongue line up with the and terminals on the charger The red light 10 on the charger indicates the battery is being fast charged When charging is finished the red light will go out and the green light 11 will light indicating that the battery is ready for use The first charge will take 2 3 hours the battery will reach maximum performance after it has been char ged 4 5 times Normal charge time is approximately 2 hours Only use the charger between 100 and 40 C in dry conditions Donotfully discharge the battery in use The battery should be re charged when significant loss of power is incurred Fig A INSERTING amp REMOVING THE BATTERY FROM THE DRILL Refer to Fig B Make sure the direction switch 1 is in the middle lock position so that the drill does not start unexpec tedly Slide the battery 7 onto the terminals on the underside of the drill it can only go in one way and will click when in place To remove battery
4. of electric shock Carefully read this manual before using the machine Make sure that you know how the machine functions and how to operate it Maintain the machine in accordance with the instructions to make sure it functions properly Keep this manualand the enclosed documentation with the machine Ferm products are manufactured to high quality standards they are safe and fit for purpose at time of sale but all tools can be dangerous if the correct precautions are not taken Always follow these instructions do not carry out the ope ration until you are sure you can do so in safety Remember to consider the work environment for safe operation as well as safety for tool use Warning When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury Read all these instructions before attempting to operate this product Save these instructions for future reference PERSONAL SAFETY Use Personal Protection Safety Equipment Protect eyes with safety glasses or goggles note the use of safety protective eyewear without the CE mark can lead to serious injury if the lens breaks A suitable dust mask should be worn if cutting drilling or sanding is dusty in particular chipboard or MDF Approved safety footwear and headgear should worn as appropriate for example on building works or when heavy weights are involved Wear a suitable apron to protect against sparks deb
5. the packaging according to the identification marks on it At the end of the product or its accessories life please recycle where facilities exist NiCd batteries are recyclable take them to a local recy cling station or phone the Helpline for current advice on recycling Helpline For any questions relating to operational or safety matters contact Ferm Customer Helplineon 0870735 Monday Friday 8am 6pm Saturday 9am pm GUARANTEE The guarantee conditions can be found on the separately enclosed guarantee card CE DECLARATIONOFCONFORMITY UK We declare under our sole responsibility that this productis in conformity with the following standards or standardized documents EN50260 EN50260 2 1 EN50260 2 2 EN60335 1 EN60335 2 29 EN5501 4 1 EN5501 4 2 EN61000 3 2 EN61000 3 3 in accordance with the regulations 98 37IEEC 73 23 EEC 89 336 EEC from 01 07 2003 GENEMUIDEN NL W Kamphof Quality department Ferm OPERATIONALSAFETY Warning The battery is normally sealed but in event of the battery being damaged be aware that it contains acid if you get any on your skin or in your eyes wash the affected parts with water immediately and seek medical advice as soon as possible Warning Do not short circuit the battery it will cause it to overheat catch fire or even explode To avoid this happening Do not connect wires to the terminals of the battery Do not expose the battery or drill to water rain o
6. UK Subjectto change USER S MANUAL Document Ref FCD3240 1 80252 Copyright These instructions are the sole property of Ferm Omega Tools and may not be reproduced Ferm cordless impact drill 32 4 V FCD 3240 I Ferm _ Screwfix art nr 80252 Ferm BV P O Box 34 8280 AC Genemuiden NL www ferm com 0307 08 English J CORDLESS IMPACT DRILLFCD 3240 I USERS MANUAL TECHNICAL SPECIFICATIONS Voltage Voltage battery charger Frequency battery charger Capacity battery 1 9 Ah NiCd Charging time 2hours 2 Speed gearbox position 0 350 min Position 2 0 1150 min Impact frequency 5600 18400 min Machine weight incl battery 3 85kg Lpa Sound pressure level 86 6 dB A Lwa Sound power level 97 6 dB A Vibration 6 65 m s PACKAGE CONTENTS Cordless drill 32 4V battery Battery charger Carry case Instruction manual Guarantee card Check the machine loose parts and accessories for transport damage PRODUCT INFORMATION Direction switch l 2 On off variable speed switch 3 Chuck 4 Torquesettingring 5 Impact sleeve 6 Battery power level indicator 7 Battery 8 Battery release buttons 2 SAFETY INSTRUCTIONS The following pictograms are used in these instructions for use AN Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual AN Denotes risk
7. e risk FAULTS Switch OFF immediately at the mains plug and remove the plug when Theplugor cable is damaged Thecharger is not operatingas it should You smell or see smoke caused by scorched insula tion in the machine or charger Overheating The ventilation slots are blocked with dirt Clean with dry cloth The machine does not start when switched on Change the battery for a fully charged one Checkthatthe battery charger is working ifthe char ging light does not come on change the fuse in the plug Take to your Ferm Dealer for repair The motor is defective Take to your Ferm Dealer MAINTAIN TOOLS WITH CARE Keep the tool clean for better and safer performance Store the accessories properly in accordance with the maker s instructions Follow instructions for changing accessories Inspect tool and extension cables periodically and if damaged have them repaired by a qualified person or authorised service body Keep handles free from oil or grease Keep the ventilation slots clean to prevent motor overheating Check for damaged parts Do not use a tool with damaged parts before further use a damaged tool must be carefully checked by a qualified person to determine that it will operate properly Check for alignment of moving parts binding or breakage of parts mounting and other conditions that may affect its operation A damaged part or guard should be properly repaired by an authorised service cent
8. r damp atmospheres Ensure that no metal objects coins nails etc are caught in the battery housing or battery socket in the drill Do not throw or dispose of the battery into water or fire Concentrate Routine and repetition can lead to mistakes Remember that a slight lack of concentration can result in serious injuries ina split second Keep work area clean Cluttered areas and benches invite injuries Consider the work environment Do not expose power tools to rain or use them in damp or wet locations Keep work area well lit Do not use power tools in the presence of flammable liquids vapours or gases Guard against electric shock This unit and its charger contain dangerous voltages Use a RCD residual current device to provide protection against electrical shock Prevent body contact with grounded surfaces e g pipes radiator ranges or refrige rators Keep children and pets away Do not let children or pets come into contact with the tool extension cable or work area Do not force the tool It will work better and safer at the rate for which it was intended Use the right tool Do not force small tools or attachments to do the job ofa heavy duty tool Do not use tools for purposes for which they were not intended for example do not usea circular saw for cutting trees or logs Secure Work Use clamps or a vice to hold work It is safer than using your hand and it frees both hands to operate the tool Do not o
9. re unless indica ted otherwise in the instruction manual Have defective switches replaced by an authorised service centre Do not use a tool if the switch does not turn on and off For advice please contact the help line Have your tool repaired by an expert This appliance is manufactured in accordance with rele vant safety standards Only experts must carry out repai ring of electrical appliances otherwise considerable dan ger for the user may result Storing tools When not in use tools should be stored in the dry out of reach of children
10. ris Wear earplugs or ear defenders Dress properly Do not wear loose clothing or jewellery It can get caught in moving parts Non skid footwear is recommended when working out doors Wear protective hair covering to contain long hair Stay alert Watch what you are doing Use common sense Do not operate tools when tired or after taking alcohol or pre scription non prescription drugs Ferm EXPLODED VIEW SPARE PARTS LIST FCD 3240 I REF NR DESCRIPTION FERM NR LEFT BOLT DRILL CHUCK 2 DRILL CHUCK 45 MOTOR 50 SWITCH 54 DIRECTION SETTING BUTTON 6l 62 IMPACT HANDLE COMPLETE 63 BATTERY PACK BATTERY CHARGER Ferm 7 ELECTRICAL INFORMATION This product is complete with a pre wired mains plug it is double insulated in accordance with EN 60335 no earth wire is required If the plug needs replacing follow these instructions Wire correctly Thewires inthe mains lead are coloured in the following way BLUE Neutral BROWN Live Blue Neutral Securing wires Secure wires carefully and firmly to the correct termi nals Secure the mains cable in the plug cord grip firmly Fit a 5 amp fuse Ifa 3amp BS1363 plug is used a BS 1362 ASTA approved 5 amp fuse must be fitted Recycle Dispose of old plug and cable Prevent inadvertent connection to socket and risk of electric shock Ifin doubt always consult a Qualified Electrician ENVIRONMENT Recycle
11. ver reach Keep a proper footing and balance atall times Disconnect tools from power supply Always remove the battery and set the direction switch to lock position Always switch offand unplug from the power supply before making adjustments or inserting batteries into charger unit Ferm Remove adjusting keys and wrenches Ensure that they are removed from the tool before swit ching on Avoid unintentional starting Do not carry plugged in tools with your finger on the switch Extension cables Use only three core earthed extension cables suitable for the power input of the charger Plug into an earthed socket only When using a cable reel unwind it fully Do not use long extension cables Outdoors use Do notuse in rain or damp conditions Connect a dust extraction device Whenever there are facilities for fitting a dust or fume extraction system make sure it is connected and used Use recommended accessories The use of any other accessory or attachment other than recommended in the instructions or catalogue may pre senta risk of personal injury Warning Before using this drill check carefully for hazards for example when drilling walls make sure you do not contact with electrical wires water pipes or asbes tos If asbestos is present cease operations and contact your local council for advice USING THE COMBI DRILL BEFORE OPERATING Check that the voltage marked on the charger is sui table for use with your
Download Pdf Manuals
Related Search