Home

SC_downloads_files/Single RF User Manual 4.2

1. All internal calculations done to a minimum 12 bit precision e Unique partial field memory for stable output syncs e Externally adjustable RF channel and audio modulation depth control e Automatic Sleep Mode for low power standby operation e Versatile I O Composite Video Input NTSC PAL 1Vpp 75 ohm Composite Video Output various standards 1Vpp 75 ohm Stereo Audio Inputs 10dBV nominal 0 2Vpp 5Vpp 20k ohm RF Output 76dByV 75 ohm approx 6mV DC power 7 14Vdc 250ma Introduction Front Panel Composite Left Right Video Audio Audio Input Input Input Status Audio LED Level Composite Video Input The Composite video input signal required depends on the operating mode and model of the converter If the converter is enabled not bypassed then a video source conforming to the NTSC or PAL SECAM video standards must be supplied to the Composite RCA or BNC input connector An NTSC source must be used with 30 fps models and a PAL SECAM source must be used with 25fps models The converter will use this video signal to convert to the model s output standard For example the SCRF405A converter with convert a PAL SECAM source to 405 251 video Connecting a video signal not conforming to the NTSC or PAL video standards will result in erratic operation in this mode If the converter is set to bypassed then the video signal on this connector is sent to the modulator with no signal processing Any video signal can be s
2. S N IU Standards Converter with RF Modulator Model s SCRE User and Technical Manual Copyright 2006 13 Aurora Design LLC Revision 4 2 12 September 2013 All specifications subject to change www tech retro com Introduction Introduction This manual covers the operation and technical aspects of the Single Standard Converter with RF Modulator The Converter is designed to accept an NTSC or PAL SECAM video signal and convert to one of several different output standards depending on the model The converted video is sent to the built in RF Modulator along with the audio and to a composite video output connector Features e Compact low power surface mount design e Front panel tri color Status LED e Flexible built in RF Modulator Up to 15 selectable carrier frequencies Programmable between 30 880MHz actual channels vary by model Supports positive negative video and AM FM audio modulation schemes e Converter bypass mode for use as stand alone RF Modulator e Up to 16 user selectable options control e Extremely stable output 3 levels 50ppm timing e Output clock line locked to input clock for perfect conversions s 10 bit video D A for greater than 54dB dynamic range e 8Mb 16Mb FLASH Memory for storing firmware and two custom images e 100K gate equivalent FieldProgrammableGateArray 250K on SCRF405A NTSC e Extremely accurate algorithms used for conversions Three line interpolation on most standards
3. 4 4 61 75 MHz 58 25 MHz 5 5 66 75 MHz 63 25 MHz 6 6 179 75 MHz 176 25 MHz 7 7 184 75 MHz 181 25 MHz 8 8 189 75 MHz 186 25 MHz 9 9 194 75 MHz 191 25 MHz A 10 199 75 MHz 196 25 MHz B 11 204 75 MHz 201 25 MHz C 12 209 75 MHz 206 25 MHz D 13 214 75 MHz 211 25 MHz E 14 219 75 MHz 216 25 MHz F Disabled Supported RF Systems System E Positive video modulation AM audio modulation audio carrier level 6dB Selector Switch Channel Video Audio Position Assignment Frequency Frequency 0 Disabled 1 1 46 00 MHz 42 00 MHz 2 2 52 40 MHz 41 25 MHz 3 4 65 55 MHz 54 40 MHz 4 5 164 00 MHz 175 15 MHz 5 6 173 40 MHz 162 25 MHz 6 7 177 15 MHz 188 30 MHz 7 8A 185 25 MHz 174 10 MHz 8 8 186 55 MHz 175 40 MHz 9 9 190 30 MHz 201 45 MHz A 10 199 70 MHz 188 55 MHz B 11 203 45 MHz 214 60 MHz C 12 212 85 MHz 201 70 MHz D Disabled E Disabled F Disabled Note Channel 1 is for the original channel from the Paris Eiffel Tower transmitter 30 Supported RF Systems System F Positive video modulation AM audio modulation audio carrier level 6dB Selector Switch Channel Video Audio Position Assignment Frequency Frequency 0 Disabled 1 1 41 25 MHz 46 75 MHz 2 1A 42 25 MHz 47 75 MHz 3 2 48 25 MHz 53 75 MHz 4 2A 49 75 MHz 55 25 MHz 5 3 55 25 MHz 60 75 MHz 6 4 62 25 MHz 67 75 MHz 7 4A 82 25 MHz 87 75 MHz 8 5 175 25 MHz 180 75 MHz 9 6 182 25 MHz 187 75 MHz A 7 189 25 MHz 194 75 MHz B 8 196 25 MHz 201 75 MHz C 9 203 25 MHz 208 75 MHz D 10 210 25 MHz
4. occurs when only three adjacent lines are used Since this converter processes all pixels within the FPGA itself it can easily handle three or four line interpolation Because of the higher clock frequency and therefore higher power consumption required for four line interpolation and because of the imperceptible difference in quality a three line interpolator is implemented in this converter Outputting Pixels Once the output pixels are generated they are up sampled by a factor of two to four by creating pixel values in between the actual ones These are then sent on to the DAC converter in this case a proprietary converter that uses a combination of R2R ladder and PWM techniques This creates an effective higher sampling frequency which allows for lower order filters with less group delay distortion RF Modulator Due to limitations in the currently available RF Modulator IC s two IC s are used with their outputs combined before being sent out the RF connector This arrangement allows for positive and negative video modulation coupled with AM and FM audio modulation Further in the case of AM audio any carrier separation between the audio and video can be achieved The FM audio carrier is limited to 4 5 5 5 6 0 and 6 5MHz from the video carrier The reference clock for both modulators is derived from a process in the FPGA This way no external crystals are required and both modulators are locked to the 21 Introduction
5. same frequency This reference clock is used by the modulators for an internal PLL with an external loop filter High quality NPO capacitors are used in the loop filter to minimize microphonics as is the case with most non Class 1 ceramic capacitors The FPGA programs the modulators as to frequency modulation type etc The video modulator receives it s input from a switch that allows the FPGA to route video from the converter output or from the video input connector The video signal goes through a sound trap filter to eliminate any frequencies that could interfere with the audio carrier The video modulator contains a DC restorer circuit that sets the correct carrier levels Audio from the two audio connectors is combined and amplified by an op amp before being sent to both modulators For FM audio the same modulator that is used for the video is enabled and the carrier spacing set Initial carrier level is set by the FPGA and depth is set by a gain control provided in the op amp circuitry For AM audio the audio section in the video modulator IC is shut down and the audio is fed to the video input of the second modulator IC Feeding the output of the op amp directly into the video input of the second modulator overrides the internal DC restorer This allows full control over the AM audio including initial level and depth To set the initial carrier level a DC offset control is provided in the op amp circuitry that allows the setting of the
6. 215 75 MHz E 11 217 25 MHz 222 75 MHz F 12 224 25 MHz 229 75 MHz 31 Supported RF Systems System M 1946 AM or FM Audio Negative video modulation AM or FM audio modulation depending on model AM audio carrier level 6dB FM audio carrier level 12dB Selector Switch Channel Video Audio Position Assignment Frequency Frequency 0 Disabled 1 1 45 25 MHz 49 75 MHz 2 2 55 25 MHz 59 75 MHz 3 3 61 25 MHz 65 75 MHz 4 4 67 25 MHz 71 75 MHz 5 5 77 25 MHz 81 75 MHz 6 6 83 25 MHz 87 75 MHz 7 7 175 25 MHz 179 75 MHz 8 8 181 25 MHz 185 75 MHz 9 9 187 25 MHz 191 75 MHz A 10 193 25 MHz 197 75 MHz B 11 199 25 MHz 203 75 MHz C 12 205 25 MHz 209 75 MHz D 13 211 25 MHz 215 75 MHz E 14 471 25 MHz 475 75 MHz F 15 477 25 MHz 481 75 MHz 32 Supported RF Systems System M 1940 Negative video modulation AM audio modulation audio carrier level 6dB Selector Switch Position moi E a E d Channel Assignment Disabled 1 2 10 11 12 13 14 15 33 Video Frequency 51 25 MHz 61 25 MHz 67 25 MHz 79 25 MHz 85 25 MHz 97 25 MHz 103 25 MHz 163 25 MHz 181 25 MHz 187 25 MHz 205 25 MHz 211 25 MHz 231 25 MHz 237 25 MHz 259 25 MHz Audio Frequency 55 75 MHz 75 75 MHz 71 75 MHz 83 75 MHz 89 75 MHz 101 75 MHz 107 75 MHz 167 75 MHz 185 75 MHz 191 75 MHz 209 75 MHz 215 75 MHz 255 75 MHz 241 75 MHz 263 75 MHz Supported RF Systems System M 1937 Negative video modulation AM audio modulation au
7. Firmware Revision History Firmware Revision History Revision 4 2 September 12 2013 1 Corrected issue on color converters with NTSC inputs where color would not lock Revision 4 1 March 12 2013 1 Corrected issue where Converter Enable user option would not get stored to EEPROM correctly Revision 4 0 March 28 2012 1 New hardware revision based on 4 x hardware now incorporates FPGA firmware factory parameters user parameters and two default images into a single serial FLASH ROM 2 Removed discreet sound trap filter Filter is now implemented in the FPGA as a digital IIR filter Revision 3 3 November 15 2011 1 Updated documents for correct terminology on Converter Enable Bypass mode 2 Added Paris Eiffel Tower transmitter frequency to System X2 38 Firmware Revision History Revision 3 2 May 28 2010 1 Changed default audio tone generation to accommodate any frequency Changed tone to 440Hz for all early standards and left at 1kHz for all later standards Revision 3 1 February 10 2010 1 Corrected error with Equalization Pulses option where it was Enabled when the Status LED was Red and Disabled when the LED was Green It now operates correctly as stated in the User Options section of this manual Revision 3 0 September 21 2009 1 New hardware revision based on 3 x hardware now incorporates FLASH based Options Settings Revision 2 1 February 21 2007 1 Updated to support revision B
8. Frequency Frequency 0 Disabled 1 P1 46 00 MHz 42 00 MHz 2 B1 47 80 MHz 45 00 MHz 3 B2 52 80 MHz 50 00 MHz 4 Disabled 5 Disabled 6 Disabled 7 Disabled 8 Disabled 9 Disabled A Disabled B Disabled C Disabled D Disabled E Disabled F Disabled Note Channel P1 was the original channel from the Paris Eiffel Tower transmitter Channels B1 B2 were the original channels from the Berlin transmitter 36 Available Models Available Models Model No SCRF 343X NTSC to 343 30i with all System X1 1934 channels Model No SCRF 343A NTSC to 343 30i with all System A channels 0 Model No SCRF 441M NTSC to 441 30i with all System M 1937 channels Model No SCRF 525M SC NTSC to 525 30i sequential color with all System M FM audio channels Model No SCRF 405A NTSC PAL SECAM to 405 25i NTSC Color with all System A channels Model No SCRF 405A PAL SECAM to 405 25i with all System A channels Model No SCRF 441X PAL SECAM to 441 25i with System X2 channels P1 and B1 B2 Model No SCRF 455X PAL SECAM to 455 25i with System X2 channels P1 and B1 B2 Model No SCRF 819E PAL SECAM to 819 25i with all System E channels Model No SCRF 819F PAL SECAM to 819 25i with all System F channels Notes 1 This unit is useful for operating 405 251 televisions in parts of the world that use NTSC video and 60Hz AC power By adjusting the vertical frame oscillator in the television NTSC video can be used to operate these televisions
9. causes the color phase to rotate by one field Caution Because of the nature of the partial field memory contained in this unit the default image is stored in bands of several lines at a time If the connected video is not stationary during the storing process the resulting image will be distorted The best way to provide a stationary image for storing is to use the output from a computer video card ora DVD PVR player in pause A typical VCR without a TBC in pause is not suitable for this use Introduction Power The converter requires a power source of between 7 0 and 14 volts DC at 250 mA A 9 volt DC power supply is recommended to reduce power consumption Voltages over 16 volts may damage the unit The unit has a reverse polarity diode in series with the input so it will not be damaged by reversal of polarity The unit uses a standard 2 1mm X 5 5mm center positive coaxial power connector as found on most consumer electronic equipment User Options As previously outlined using a small tool such as a paper clip carefully press the Options Button for 1 second This will place the unit into the Options Setting Mode Next choose the desired option using the Selector Switch The front panel Status LED will blink green if the option is enabled red if it is disabled and yellow if not supported To change the state of the option momentarily depress the Options Button to toggle between enabled and disabled When all desired options are s
10. image FLASH memories Revision 2 0 January 16 2007 1 Updated for revision 2 0 hardware 2 Added externally adjustable RF channel select switch 3 Added audio test tone in default mode Revision 1 8 August 26 2006 1 Updated 441 251 standard to match German specifications 2 Added channels B1 and B2 to System E for Berlin transmitter 39 Firmware Revision History Revision 1 7 June 18 2006 1 Increased internal fpga clock frequency to ease filter design Revision 1 6 June 12 2006 1 Added Sleep Disable feature to Option switch position 7 2 Modified SCRF 819F and SCRF819L units for dual RF system capability Revision 1 5 May 18 2006 1 Increased accuracy of sine wave generator for internal test modes 2 Added functionality to Test Mode 2 to measure SNR of D A Revision 1 4 May 8 2006 1 Improved the high frequency video response of the unit Revision 1 3 May 3 2006 1 Improved timing to image FLASH 2 Added a sixth test mode to aid in modulation depth measurements Revision 1 0 April 6 2006 1 Initial release Note Hardware Firmware revision level can be found on bottom label of unit 40
11. input bias Modulation depth is set by the same gain control The outputs of the two modulators are then combined through a balanced network that maintains a 75 ohm impedance and sent to the RF connector Hardware Setup and Test Mode There is a hidden mode of operation that is used during initial setup and test of the converter that may be useful to those users with a technical understanding of the operation of a standards converter No harm can be done to the unit by simply entering this mode but care should be taken if the following alignment procedure is attempted To enter the Setup and Test Mode remove the power cable from the unit While depressing the Auxiliary Button on the rear panel reconnect the power supply to the unit The Auxiliary Button must remain depressed until the front panel Status LED starts blinking At this point the pushbutton may be released The Status LED will 22 Introduction repeat a pattern of two fast yellow flashes to indicate the unit is in the Setup and Test Mode There are two different behaviors that can be selected You can scroll through these by depressing the auxiliary pushbutton to increment to the next test in a round robin fashion Note a valid RF channel should be selected on the Selector Switch when running the Setup and Test Mode Mode 1 This mode is used to examine the unmodulated audio and video carrier levels no audio signal should be connected to the unit during this test Additio
12. time should the RF output from this unit be connected to an antenna for the purpose of broadcasting the signal While no damage will result to the unit it is against the law in most countries to use a modulator in such a manor The audio from the source device VCR DVD etc should be routed to the converters audio inputs Two inputs are provided with low cross talk so a stereo audio signal can be fed to the unit The two channels are combined into a mono signal If only a mono audio source is available it can be fed to either input For additional audio gain a Y cable can be used with a mono source to feed both inputs The use of high quality video cables is recommended for best results Cables conforming to 75 ohm impedance should be used on the video inputs and outputs Cables of lesser quality can be used for the audio channels There should now be a solid green status light on the front panel indicating a locked video signal as described previously and a stable image on the television To help aid in setup when no video input is presented to the converter it will output a default image This can be useful in making final adjustments to the television The audio level control can be adjusted to set the audio RF modulation depth for the connected source This control should be set to the maximum setting without causing distortion of the audio If the audio is distorted this control should be lowered slightly If the audio is low in
13. volume or noisy this control should be raised It can be adjusted my inserting a small flat blade screw driver in the hole in the front panel A clockwise turn will increase the level while the opposite will decrease the level 14 Introduction An additional benefit of the converter can be found in it s video processing path Since most early television sets did not have Vertical Blanking Interval Suppression or Chroma Traps retrace lines and moire patterns can be visible when using modern video signals The converter will suppress the VBI signals eliminating retrace lines and contains a 4 line adaptive comb filter to remove the chroma signal Theory of Operation In order to convert between different video standards of the same frame rate only spatial correction is required Spatial correction involves changing the resolution size and aspect ratio of the incoming video to the output video format This can be easily achieved through standard digital methods utilizing scalers and FIR filters This will be discussed in detail It was decided that no off the shelf components existed that would provide the desired functionality so a FieldProgrammableGate Array or FPGA was chosen to provide all the digital functionality By adding input output circuitry memory and ancillary circuitry to the FPGA the entire system could be realized The basic building blocks to the design are FPGA video decoder ADC video DAC RF modulators image
14. FLASH memory audio amplifier and multiple power supplies A brief description of each part follows FPGA Xilinx XC3S100E 4VQ100 XC3S250E 4VQ100 100K gate equivalent 250K gate equivalent 72Kb Block RAM 216K Block RAM 1 2V Core 2 5V Aux 3 3V I O Video Decoder TI TVP5150A 9bit ADC s 2X Over Sampled Line Locked Clock 4 Line Adaptive Comb Filter Multiplexed 8bit YCrCb output bus Video DAC Proprietary Design 10bit effective DAC 35 MSPS maximum conversion rate 56 dB SNR 15 Introduction RF Modulators Freescale MC44BS373CA One for video and FM audio one for AM audio 30 880MHz Frequency Range 76dByuV Output Level FLASH Memory Winbond W25Q80BV Winbond W25Q16CV 8Mb Serial FLASH ROM 16Mb Serial FLASH ROM Topology A block diagram of the circuitry is shown below Options Selector Push Button EO Composite Output Audio iic RF Input Output The incoming video is digitized and processed by the TVP5150A using a 14 318MHz reference crystal to the ITU 601 formerly known as CCIR601 specification All internal timing is generated using this crystal The video is 16 Introduction quantized processed for brightness contrast chroma gain and hue among others and output at the ITU rate of 27MHz on an 8 bit time multiplexed bus with alternating luma and chroma samples No other signals are required from this circuit as the ITU specification describes a method for encrypting the horizontal
15. Lines Horizontal Vertical Frequency Video Characteristics Supported Conversions PAL SECAM to 819 25i Belgium 4 3 0 73 0 59 53 6 MHz 2X 720 760 20 475 Hz 25 0 Hz 8 9 MHz 6 9MHz 1 Vpp into 75 ohms composite sync 70 30 video sync ratio 4 3 1 32 1 02 29 5 MHz 3X 720 410 11 375 Hz 25 0 Hz 4 9 MHz 3 8 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 6 5 1 29 1 03 24 4 MHz 4X 648 418 11 025 Hz 25 0 Hz 4 1 MHz 3 2 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 4 3 1 43 1 14 26 3 MHz 4X 720 378 10 125 Hz 25 0 Hz 4 4 MHz 3 4 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 27 Supported Conversions PAL SECAM to 405 25i NTSC Color Image Pixel Aspect Ratios 4 3 1 43 1 14 Interpolator Clock Oversample 26 6 MHz 4X Active Pixels Lines 720 378 Horizontal Vertical Frequency 10 125 Hz 25 0 Hz Video Characteristics 4 4 MHz 3 4 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio Chroma Subcarrier Frequency 2 657 812 5 Hz Note numbers in brackets are effective parameters 28 Supported RF Systems 29 Supported RF Systems System A Positive video modulation AM audio modulation audio carrier level 6dB Selector Switch Channel Video Audio Position Assignment Frequency Frequency 0 Disabled 1 1 45 00 MHz 41 5 MHz 2 2 51 75 MHz 48 25 MHz 3 3 56 75 MHz 53 25 MHz
16. and vertical timing information directly into the digital data using timing reference makers or TRS codes A brief description of the ITU 601 656 specification is as follows Fundamental quantization frequency 13 5MHz Pixel Resolution 720 H x 486 V NTSC 720 H x 576 PAL Image Aspect Ratio 4 3 Pixel Aspect Ratio 1 1 NTSC 0 9 PAL Horizontal Frequency 15 734 Hz NTSC 15 625 Hz PAL Vertical Frequency 29 97 Hz NTSC 25 Hz PAL Clocks per Line 1716 NTSC 1728 PAL 27MHz clock Clocks per Frame 900900 NTSC 1080000 PAL 27 MHz clock Note that the vertical frequency is 29 97Hz for NTSC not 30Hz as expected This is due to the NTSC color system that was first ratified in 1953 All monochrome television transmissions prior to this standard used exactly 30Hz or 30 frames per second so as to be in sync with the AC line frequency This is done to reduce distortions in the image due to induced AC fields or hum from the power supplies of these early sets In order to devise a compatible color system that would show a monochrome signal on existing sets RCA proposed a method of modulating the color components of the video signal onto a subcarrier in the video For reasons beyond the scope of this manual a frequency needed to be chosen so that no standing patterns in the color signal would result This required lowering the vertical frequency from 30Hz to 29 97Hz While this change caused no adverse side effects on televisions
17. carrier Also in this section a video switch is provided ahead of the sound trap filter that allows the video input to the RF Modulator to come from the 18 Introduction output of the DAC or directly from the composite video input connector as used in the bypass mode Audio from the audio input connectors is combined filtered and amplified before being sent to the RF Modulator An externally adjustable potentiometer sets the gain of the audio amplifier thereby setting the modulation depth of the audio RF carrier An internal potentiometer sets the initial audio RF carrier level for AM modulation schemes FM modulation schemes are handled internally to the RF Modulator IC s Detailed Analysis Generating an output clock As shown in the previous section a clock synchronous to the output standard but related to the incoming video clock must be generated This is done using the DCMS built into the FPGA First we need to decide what output clock frequency we need Taking the example of 625 input with 405 output it will be shown that the active video time per line is essentially the ratio between the two formats For 625 the active line time is 51 95ys while the 405 active line period is 80 30ps 405 625 is 0 65 while 51 95 80 30 is 0 65 This means we can use the same number of pixels per line in the 405 format as there are in the 625 If this were not the case we would need to take into account the difference in pixel counts into the fi
18. d the unit enters the Option Setting Mode and freezes the currently selected RF channel By using the Selector Switch you can choose the desired option position The front panel Status LED will blink green if the option is enabled red if the option is disabled and yellow if the option is not supported When the desired User Option is chosen using the Selector Switch the Option Button is pressed momentarily to toggle the option between enabled and disabled Each option can be programmed in this manner When finished the Option Button is once again depressed for 1 second to exit the Option Setting Mode Also if no changes of the Selector Switch or Option Button are detected for 1 minute the unit will automatically exit the Options Setting Mode and return to normal operation When the unit returns the normal operation the Selector Switch may need to be returned to the desired RF Channel RF Output This F connector provides the RF output from the modulator This output should terminate into a 75 ohm load It should only be used to connect directly to the antenna terminals of a television set or to a local distribution amplifier if driving 7 Introduction multiple televisions and never be used for broadcast purposes For complete information about the characteristics of this output please refer to the Specifications section found later in this manual Caution The RF output from the internal modulator is double sideband and rich in har
19. d to select the color sequence of the output When Disabled the color fields in the output will be in a Red Green Blue sequence When Enabled the color fields in the output will be in a Red Blue Green sequence This option should be set to match the order of the filters in the color wheel Position 3 Equalization Pulses SCRF405 SCRF343 only This option is used to control the equalization pulses in the vertical frame sync for the 405 251 and 343 301 models This option is not supported on all other models When these formats were first created they did not include equalization pulses in the vertical frame sync Because of this poor interlacing of the image can result due to difficulty of the vertical frame oscillator in the television properly locking to the signal Equalization pulses are added before and after the serration broad pulses to improve the vertical frame oscillator s ability to lock to the sync signal All modern analog video formats utilize equalization pulses in the sync When this option is Enabled equalization pulses will be added to the listed formats for better synchronization While this does create a better interlaced image 10 Introduction it is not historically accurate and does not represent the formats as they would have originally appeared When this option is Disabled the equalization pulses will not be added resulting in the formats as they would have been originally This may result in a poor
20. dio carrier level 6dB Selector Switch Position moi E a x d Channel Assignment Disabled 1 2 10 11 12 13 14 15 34 Video Frequency 45 25 MHz 51 25 MHz 67 25 MHz 79 25 MHz 85 25 MHz 97 25 MHz 103 25 MHz 157 25 MHz 163 25 MHz 181 25 MHz 187 25 MHz 205 25 MHz 211 25 MHz 235 25 MHz 241 25 MHz Audio Frequency 49 75 MHz 55 75 MHz 71 75 MHz 83 75 MHz 89 75 MHz 101 75 MHz 107 75 MHz 161 75 MHz 167 75 MHz 185 75 MHz 191 75 MHz 209 75 MHz 215 75 MHz 239 75 MHz 245 75 MHz Supported RF Systems System X1 1934 Negative video modulation AM audio modulation audio carrier level 6dB Selector Switch Position R E E a x d Channel Assignment Disabled 1 2 10 11 12 13 14 15 Video Frequency 44 75 MHz 49 75 MHz 54 75 MHz 62 75 MHz 67 75 MHz 72 75 MHz 77 75 MHz 82 75 MHz 112 75 MHz 117 75 MHz 122 75 MHz 127 75 MHz 132 75 MHz 137 75 MHz 142 75 MHz Audio Frequency 47 00 MHz 52 00 MHz 57 00 MHz 65 00 MHz 70 00 MHz 75 00 MHz 80 00 MHz 85 00 MHz 115 00 MHz 120 00 MHz 125 00 MHz 130 00 MHz 135 00 MHz 140 00 MHz 145 00 MHz Note There were no official channel assignments at this time only the bands of 42 56MHz 60 86MHz and above 110MHz were allocated to television 35 Supported RF Systems System X2 1936 Positive video modulation AM audio modulation audio carrier level 6dB Selector Switch Channel Video Audio Position Assignment
21. e spatially converted Many aspects need to be taken into account such as image aspect ratio and the number of active lines The distinction of image aspect ratio is made here to differentiate it from pixel aspect ratio which only has to do with how the analog data is quantized Since this converter is limited to the type of input and output video handled no spatial correction needs to take place in the horizontal direction This means that all 720 input pixels will be included in the output line but at the output clock rate Only spatial correction in the vertical direction needs to take place On first inspection it would appear that this correction can easily be achieved by simple adding or dropping lines to get the desired result For example if you have 576 lines in the input and need 384 lines in the output dropping every third line would appear to be adequate This is known as decimation Unfortunately one third of the original information 15 lost not being included in the output in any way and since the input lines were spaced differently than the output lines aliasing of the image will occur This is most noticeable as stair stepping or jagged edges around objects To avoid this situation all lines in the input need to be used to generate the output A simple solution for the above case would be to use the first line of the input as the first line in the output and then average the next two lines of the input to create the second l
22. eful when only an RF Modulator is required as with the use of custom or nonstandard video signals or for experimentation Since the video is sent unprocessed to the modulator it is the responsibility of the user to verify the suitability of this signal Also the Sleep and Audio Tone features are not available when operating in this mode and will be disabled regardless of the settings in the Option Switch 12 Introduction Default Mode When the unit is in the Normal or Converter Only modes and no valid video is connected to the composite input the unit will output one of the two images stored in the FLASH on it s outputs and an audio tone will be injected into the audio path if enabled This can be used to verify operation of the unit or aid in setup of the television The unit is shipped with appropriate test patterns stored in the FLASH but this can be over written at any time as previously explained Options Setting Mode When the unit is in the Options Setting Mode various options can be set by the user to control the behavior of the unit These settings will be saved to an internal FLASH memory and are retained even if power is lost Sleep Mode Since no power switch is supplied on this unit an automatic Sleep Mode will be entered whenever the video input is not present for more than 1 hour This feature is available when operating in the Normal or Converter Only modes It is not available in the RF Modulator Only mode Wi
23. et again depress the Option Button for 1 second to exit the Options Setting Mode The unit will also automatically return to normal operation if the Selector Switch and Option Button are not changed for 1 minute Note Be sure to return the Selector Switch to the desired RF Channel setting after changing the User Options Position 0 Converter Enable All models This option is used to enable bypass the internal Standards Converter and use the unit as a stand alone RF Modulator When Enabled the converter and modulator operate normally When Disabled the converter is bypassed and the video signal on the composite input connector is sent directly to the modulator Introduction Position 1 Sleep All models This option is used to disable the automatic Sleep Mode When Enabled the Sleep Mode will operate normally as discussed in the next section When Disabled the unit will not go to sleep This can be useful when using the unit as a test pattern generator and no video input signal is connected Position 2 Audio Tone All models This option is used to disable the Audio Tone in the default mode When this switch is OFF the Audio Tone will output when no valid video source is connected to the converter When this switch is ON the Audio Tone will be disabled This can be useful if other audio is connected to the converter and the Audio Tone is not desired Position 3 RGB RBG Select Model SCRF525M SC Only This option is use
24. hase of the Chroma Carrier and the line timing however if 11 Introduction there is instability in the source video there will be instability in the Chroma Reference resulting in poor color locking of the television This mode should only be used when the source video is from a stable source like a DVD or digital receiver When Enabled the Chroma Reference is derived from a fixed clock This mode will always output a stable Chroma Carrier regardless of the source video but the Chroma Carrier to line timing may vary Operating Modes Normal Full Operating Mode When valid video is present the Status LED will show a Solid Green light and the unit will output converted video on the composite output connector and on the RF connector This is the most common operating mode Converter Only Mode This mode is similar to the Normal Full Operating Mode except the RF Channel Selector Switch is set to 0 disabling the RF modulator In this mode the converted video output will only be present on the composite video output connector This mode is useful when connecting to a video monitor that has a composite video input RF Modulator Only Mode Converter Bypass In this mode the standards converter is bypassed and placed into a low power mode The video on the composite input connector is only processed by an audio trap filter before being sent to the modulator along with the audio that is present on the audio input connectors This mode is us
25. ideo Levels Video Timing Video SNR Audio Input Audio Input Audio Response Specifications NTSC 29 97fps PAL 25fps SECAM 25fps Obit A D 8 bit data Composite 1 Vpp 75 ohm impedance Composite 1 Vpp into 75 ohms 10 bit Effective D A 3 of output standard 50 ppm Line PLL locked lt 2ns jitter typical 56dB typical Unbalanced 20K impedance 10dBV nominal input level 0 2Vpp to 5Vpp maximum 50Hz to 15kHz 2dB 24 RF Output RF Output Video SNR Modulation Depth Audio SNR General Dimensions Weight Power Requirements Humidity Temperature Specifications 76dBuV 6 3mV typical into 75 ohms Crystal PLL frequency generation 56dB typical 99 maximum 54dB typical 2 60 X 2 60 X 1 00 66mm X 66mm X 25mm 2 50z 70g 9Vdc typical 7 14Vdc maximum 2 0 watts typical Full Operation 1 0 watt typical Sleep Mode 20 80 non condensing 10C 45C ambient 50F 110F 25 Supported Conversions Supported Conversions NTSC to 525 301 Sequential Color Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics NTSC to 441 301 Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics NTSC to 343 301 Image Pixel Aspect Ratios Interpolator Clock Ove
26. ine in the output This is known as two line interpolation While it provides a vastly superior image to straight decimation it has several draw backs First the output lines will have different frequency content because one line in the output is the same as a line of the input with all vertical frequencies intact while the next line in the output is the average of two lines of the input with the frequencies filtered down Also since this is just a simple averaging filter aliasing can occur introducing image data that does not actually exist 20 Introduction Then consider the case where the output is not a clear division of the input In the example there were exactly 2 3 the number of lines in the output as there were in the input Now take the case of 625 input to 441 output This requires scaling 576 input lines to 406 output lines or a 406 576 ratio which can be reduced to 203 288 Not an easy ratio to handle with a simple two line interpolator By taking more lines into account a much more accurate representation of the desired ratio can be achieved By comparing the desired spatial position of the output line to the input lines and taking a weighted average of several lines around this point a high quality filter or interpolator is realized Through actual tests it has been shown that carefully chosen weighting coefficients used with four lines gives the best results It has also been shown that no perceptible loss of image quality
27. is control is required to handle the variations in the audio output levels from different devices This control should be set to the maximum possible without causing distortion of the audio in the RF signal The potentiometer is adjusted by inserting a small flat blade or phillips screw driver into the hole and turning it until it engages the rotor of the potentiometer Maximum drive is obtained by turning the potentiometer clockwise Introduction Rear Panel Composite Video RF 9Vdc Output Output Input Selector Switch Options Button Aux Button Composite Video Output This RCA or BNC connector provides the video output from the converter This output should terminate into a 75 ohm load This output is only valid when the converter is not set to bypass mode If the converter is set to bypass mode no signal will be present at this output For complete information about the characteristics of this output please refer to the Specifications section found later in this manual Selector Switch The dual purpose Selector Switch used to select the output frequency or channel of the RF output in normal operation and to select the user option during options programing During normal operation the Selector Switch selects the channel of the RF output The specific frequency or channel for each position is unique to the model of converter and can be found on the bottom label of the converter and in the Supported RF Systems section found late
28. it has created a legacy of problems for modern video equipment Instead of being able to use integer numbers like 24 25 and 30 we now have to include 29 97 which makes many calculations and conversion extremely difficult For digital processing the ratio 1000 1001 has been established as the conversion between 30 and 29 97 video 17 Introduction The digital video data is then routed to the FPGA where it is further processed The data is sent to the internal partial field memory in round robin fashion The partial field memory is large enough to hold many lines of video so there is always enough data to keep an uninterrupted flow to the output All the above processing is done synchronous to the ITU clock so no additional clocks are necessary at this point Before any further processing can be done a new clock synchronous to the output standard but integrally related to the ITU clock must be generated The internal DCM s are used for this purpose By carefully choosing the ratio s and cascading two DCM s together the exact frequency for the output standard can be generated in the FPGA This clock needs to run at least three times the actual pixel clock desired for reasons that are shown below but it is actually run at six to twelve times to provide for oversampling and running the proprietary DAC With this new output synchronous clock a video timing generator or flywheel is created in the FPGA to generate all timing signals for
29. ly interlaced image on the television exactly as it would have been when originally broadcast Position 4 Color Select SCRF525M SC amp SCRF405A NTSC This option is used to select the output mode of the converter between color and monochrome When Enabled the converter will output a color signal When Disabled the converter will output a monochrome signal Position 5 Chroma Gain Model SCRF525M SC Only This option is used to control the Chroma Gain of the converter When Disabled the gain is set to standard CCIR levels resulting in the output matching the input s chroma levels When Enabled the gain is increased by 33 resulting in the output levels being higher than the input levels For instance in this position standard SMPTE 75 color bars will appear as fully saturated 100 color bars on the output Position 5 Cross Color Filter Model SCRF405A NTSC Only This option is used to control the Cross Color Filter When Disabled the luminance channel is not modified When Enabled a 12dB filter at the chroma subcarrier frequency is added This filter may help reduce dot crawl effects in the composite output The filter characteristics match those of the original BBC specification Position6 Chroma Reference Model SCRF405A NTSC Only This option is used to control the Chroma Reference Clock When Disabled the Chroma Reference is derived from the source video This mode retains correct relationship between the p
30. monics and should never be broadcast without filtering Auxiliary Button The Auxiliary Button is used to store a default image into the internal FLASH memory and to toggle between the two stored images On the SCRF525M SC there is only one stored image and the button is additionally used to control the color phasing of the output To store a default image first with no video source connected select the desired stored image to overwrite by momentarily pressing the Auxiliary Button until the desired image is displayed Next the converter must be in it s normal operating mode with a valid video input connected and a Solid Green Status LED If a valid video input is not connected an image cannot be stored With a stable stationary video input applied the Auxiliary Button may be pressed and held for 4 seconds by inserting a paper clip or other small tool into the hole in the back of the unit The Status LED will begin to flash green quickly indicating storing of the image FLASH is taking place This process can take up to 10 seconds and the video signal must not be disturbed during this process After the image is stored the Status LED will return to solid green Once an image is stored whenever there is no video input connected to the unit the default image stored in the FLASH will be outputted By momentarily pressing this button the user can toggle between the two stored images On the SCRF525M SC momentarily pressing this button
31. nal ratio The final ratio for this example only needs to account for the difference in the number of lines therefore the base ratio we need is 405 625 which can be reduced to 81 125 If we multiplied the ITU 27MHz clock by this number we would get a clock that has two counts per pixel in the output since there are two clocks per pixel in the ITU clock As stated earlier we need a clock that has at least 3 clocks per pixel in order to achieve the minimal three line interpolation necessary for good image quality Also we actually want a clock two to four times higher than this so the output can be over sampled easing the filter requirements and yielding a higher SNR This means the output clock needs to use the base ratio times 3 2 to get to the 3 clocks per pixel and then again by 4 So the final ratio required is 81 125 3 2 4 or 486 250 Taking this ratio and multiplying by the 27MHz ITU clock the output clock becomes 104 98MHz 19 Introduction Using this new output clock all processing of the output pixels can be accomplished while still maintaining a lock to the input clock If this were not done and the output clock was unrelated to the input clock as is the case with using a separate oscillator the output image will have duplicate dropped or torn frames Spatial Correction With an output clock now available the image can be processed In order to convert between different video standards the video image must first b
32. nally the AM audio carrier level can be set in this Test Mode To set the AM Audio carrier level connect a spectrum analyzer to the RF output and set so that both the audio and video carriers are visible Momentarily short the Test Point TP1 inside the converter must remove case lid with a screw driver or similar tool The Status LED will show two fast red flashes to indicate AM Audio Carrier Level Setting Mode Using the Options and Auxiliary Buttons the level can be adjusted up or down relative to the Video carrier level Once the desired level is obtained momentarily short TP1 again to save the result in FLASH memory and return to the normal Test Mode To exit the AM Audio Carrier Level Setting Mode without saving the value remove power from the unit Mode 2 In this mode a video test pattern consisting of a linear ramp will be output from the unit on both the composite output and RF output This test is used to validate the output section of the converter Updating Firmware If it ever becomes necessary to update the firmware in the unit this can be accomplished through the internal programming port The connector is a standard 8 pin double row 2mm connector A custom cable with the appropriate mating connector 15 used in conjunction with an Asix Presto or similar programmer 23 Specifications Video Input Supported Standards Video Quantization Video Input Video Output Video Output Video Quantization V
33. r in this manual When the switch is set to 0 the RF modulator is disabled and put into a low power state In this mode the unit will still output a converted video signal on the composite output connector This control is adjusted by inserting a small flat blade or phillips screw driver into the hole and engaging the slots in the switch 6 Introduction If the Option Button is pressed see below the current RF channel is frozen and the Selector Switch is used to select the desired user programable option Note The converter provides a digital sound trap filter in the video path This filter removes any frequencies in the video that are close to the audio carrier frequency This filter is automatically enabled when the Selector Switch is set to a valid Channel position Since the same video signal is sent to the Composite Video Output and the internal RF modulator the Composite Video Output will also have the sound trap filter enabled when a valid Channel is selected If the Composite Video Output is to be used without the RF Modulator the Selector Switch should be set to the 0 position to disable the RF modulator and the digital sound trap filter Options Button This pushbutton is used to enter the Options Setting Mode and to change the state of the User Options The button can be depressed by inserting a paper clip or other small tool into the hole in the back of the unit When the Option Button is depressed for 1 secon
34. rsample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics 4 3 1 13 0 88 40 5 MHz 2X 720 480 15 735 Hz 29 97 Hz 6 7 MHz 5 3 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 4 3 1 35 1 04 34 0 MHz 3X 720 406 13 217 Hz 29 97 Hz 5 7 MHz 4 4 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 4 3 1 70 1 37 26 5 MHz 4X 720 316 10 280 Hz 29 97 Hz 4 4 MHz 3 5 MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio PAL SECAM to 819 25i France Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics 4 3 0 73 0 59 53 6 MHz 2X 720 738 20 475 Hz 25 0 Hz 8 9 MHz 6 9MHz 1Vpp into 75 ohms composite sync 70 30 video sync ratio 26 Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics PAL SECAM to 455 25i Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics PAL SECAM to 441 25i Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels Lines Horizontal Vertical Frequency Video Characteristics PAL SECAM to 405 25i Image Pixel Aspect Ratios Interpolator Clock Oversample Active Pixels
35. th this feature the RF Modulator is shut down along with the standards converter image FLASH and the video output Only the video decoder is left active to signal when a valid video input is again supplied to the unit to wake it up This Mode can be disabled using one of the internal option switches This is useful when the unit is used as a test pattern generator and no video input is connected Typical Connections In normal usage the desired RF Channel is chosen on the RF Channel Select switch as previously described The power adapter is connected to the converter and to the AC power source A valid NTSC or PAL SECAM video source should then be connected to the video input The video source can be anything from a VCR toa 13 Introduction DVD to an off air broadcast For the best quality a DVD or PVR is recommended The video output can then be connected to the input of a video monitor or the RF output can be connected to the antenna terminals of a television A balance transformer may be needed to convert the 75 ohm output of the unit to the appropriate signal type for the television Caution The RF output from the internal modulator uses a double side band modulation technique and is not suitable for broadcast without filtering Also due to the method of frequency division provided in the RF modulator IC s their outputs are rich in harmonics It is intended to only be connected directly to a television s antenna input At no
36. the model s output standard All horizontal vertical pixel count and line count generation is done in this process Additional frame timing signals in the form of equalization and serration pulses can be generated This is the main heartbeat process for the entire design Using these timing signals the video data that was stored in the partial field memory synchronous to the incoming ITU video clock can now be clocked out synchronous to the new output clock The data only needs to be downscaled vertically before being output to the video DAC This is done by reading three pixels out of adjacent lines and interpolating the desired output pixel Since three pixels need to be read out of the memories for each pixel sent to the DAC this is why a three times clock is required With all the above timing now generated the output video can be created The signals from the flywheel are routed to the video output DAC at the appropriate times in the signal while the processed video from the partial field memory is routed to the video DAC during the active portions of the video signal The DAC is run at a two to four times over sampled rate to reduce filtering requirements and increase SNR The video is then filtered and buffered before being sent to the composite output connector and to the RF Modulator section In the RF Modulator the video is sent through a sound trap filter to remove any video frequencies that would interfere with the audio RF
37. upplied in this mode although it is the users responsibility to verify this video signal to obtain the desired result from the modulator Audio Inputs Two RCA connectors are provided for audio input The two connectors are summed internally into a mono signal that is fed to the RF modulator If only a mono source is available it can be connected to either of the audio input connectors or both through a Y cable if higher input gain is required The inputs can accept a 4 Introduction wide range of audio input levels but are designed to work optimally with standard consumer level 10dBV audio signals Due to the variance of audio output levels from many devices an audio input gain control is provided which allows the user to set the modulation depth of the audio RF carrier to suite the source level Please refer to Specifications sections found later in this manual Status LED The tri color status LED conveys the current operating state of the converter Solid Red No video input signal detected Default image will be output Solid Green Converter locked to video input Normal operation Slow Flashing Options setting mode Red Option Disabled Green Option Enabled Yellow Option Not Available Pulsating Red Converter in low power Sleep mode Fast Flashing Converter storing default image to internal FLASH Green Audio Level The Audio Level control is used to set the modulation depth of the audio RF carrier Th

SC_downloads_files/Single RF User Manual 4.2

Contents

Download Pdf Manuals

Related Search

Related Contents