Studio 8 Product Manual
Contents
1. V These instructions are not a substitute instructional manual for glass fusing of ceramic and porcelain elements voer BMENSION MAK vors amps warts SEOPT rus m SuPpING HB 120 6 x 4 5 x6 1800 120V 12 1440 5 15R 15 12 20 Lbs HB 230 6 x 4 5 x 6 1800 230V 9 6 2208 6 20R 20 12 20 Lbs Studio 8 8 x 4 5 x 8 1800 120V 12 1440 5 15R 15 12 30 Lbs Studio 8 8 x 4 5 x 8 1800 230V 9 6 2208 6 20R 20 12 30 Lbs Plug configuration may differ based on country of use Basic Firing Instructions 1 Prepare the shelf with Shelf Primer and dry thoroughly 2 Position the glass on the mold for slumping or on the shelf for fusing 3 Place shelf or mold with the glass in the kiln 4 Turn the kiln on medium temperature until it reaches 1000 F 5 Turn the kiln to High and fire until the glass reaches the desired bend or fuse 6 Turn the kiln off when the glass is to your liking 7 Flash vent to 1000 F 8 Anneal in the kiln for 10 minutes and transfer to a fiber blanket or leave in the kiln until room temperature Firing in warm pre fired kiln 1 Cool the kiln to approximately 500 degrees 2 Allow the glass or mold with glass to absorb heat in the kiln for 3 minutes 3 Continue to fire as above NOTE Firing schedules vary dependant on the size and thickness of glass Larger pieces must have a s2. evenheat www evenheat kiln com SAFETY PRECAUTIONS Vv Read All Instructions and safety precautions before using kiln Do not touch hot sides Keep unsupervised children away from kiln Place Kiln on noncombustible surface Do not install closer than 12 from any wall or combustible surface Do not use near any flammable material Fire in only well ventilated area No small closet type areas gt Never use with an extension cord gt UV protective eye wear is suggested for looking in kiln TEST FIRE A test fire should be done in your kiln to burn off any residue from the kiln or shelves To do a test fire kiln should be placed on a level noncombustible surface away from any combustible materials Place kiln washed shelves in kiln Put lid on kiln and turn infinite switch to 5 Watch pyrometer until kiln reaches 1200 then turn kiln off and unplug it Do not touch until kiln is cool INSTRUCTIONS gt Place kiln on a level noncombustible surface Keep away from curtains and other combustible materials gt Vacuum dust from the kiln every few firings Dust particles falling will contaminate glass or glazed ware gt Place kiln washed shelf on base of kiln Glass separator could be used instead of kiln wash gt Never put glazes and glass directly on base to prevent kiln bottom from wearing out gt Never use kiln wash on sides of kiln or on the VVVV Vv Studio 8 Hot Box Installation and Operat
3. ing Manual North American Models gt Dangerous voltage Do not touch elements with anything gt Donot leave kiln unattended during firing gt Wear protective glasses when lifting top to look into the kiln during firing Keep your face at least 15 away from kiln when looking into the hot firing chamber Never fire organic materials inside you kiln When firing is completed always unplug kiln Do not use the window lid for a base heat loss may damage supporting surface VV V gt Place glass or ware onto kilns shelf being careful not to get anything on elements gt With infinite switch in the off position plug in kiln gt The Hot Box amp Studio 8 uses an infinite switch to control temperatures Using this type of switch allows the user to have a heating range from 0 100 power output The control knob positions are 2 for LOW position 4 1 for MEDIUM and HI for HIGH This gives the kiln operator the option of how slow or how fast they want their piece to fire gt Watch the kiln pyrometer until the kiln has achieved the temp desired Once the kiln has reached temperature turn kiln off Do not touch kiln until kiln is cool When firing glass in this kiln you may find the need to cool the kiln down fast To do so use HOT MITTS and flash vent lift lid off and on frequently while kiln is cooling Always wear protective glasses and keep face at least 15 away from kiln VV
4. lower firing schedule to avoid cracking You will find that items fired in the Hot Box amp Studio 8 may not follow the same firing schedules as those used for the larger sized glass kilns Due to the quicker rise in temperature you may need to reach a higher end temperature and hold it there till desired results are achieved or hold it longer at the lower temperature till desired results are achieved This Hot Box Studio 8 has been calibrated to 1700 F There are books on the market with detailed instructions on firing the small mini kilns We have used Sculptural Effects and Garden Delights by Debra and Steven Vantol as our reference These books are available from your glass supplier evenhecat www evenheat kiln com
Download Pdf Manuals
Related Search