SAT PROGRAMMER
Contents
1. confirm selection with the OK key or press the C key to keep the previous setting SETTING THE ACCESS CODES FUNCTIONS 200 201 202 300 The access codes can be set up to your own level installer level The codes that refer to the Disarm or unblocking code function n 200 Anti code function n 201 Unblock functions code function n 202 can be changed but it is not possible to see the stored code Your own installer code is however visible For vehicles with a system that you did not install yourself the Service Centre can set the default password so that the functions can be accessed Setting the Disarm Anti car jack Unblock functions codes Select the function required n 200 n 201 n 202 press OK key in the new code directly on the keypad it must have from 5 to 8 digits numbers only confirm selection with the OK key or press the C key to keep the previous setting 11 Setting the new installer code Select the function required n 300 press OK key in the new code directly on the keypad it must have from 5 to 8 digits numbers only confirm selection with the OK key or press the C key to keep the previous setting Setting the polarity of the VOLI input function 362 The polarity of the VOL1 input can be altered The polarity of the VOL1 input must be set according to the type of signal positive or negative from the auxiliary output of an external alarm Sele2. The Service Centre activates the peripheral unit directly during the testing and programming stage Should the Customer require the vehicle to be delivered without it being activated by the Service Centre the peripheral unit can be activated locally by following the steps below Access Installer Level as described on page 8 Maintenance Select function 431 Disable To exit Installer Level when the display shows AIDE A press the zero key twice and then 2086 The Access denied S P will display Insert code The peripheral unit is disarmed by switching on the dashboard and keying in the password The S P will now display SAT OK From this moment on the peripheral unit is armed and disarmed according to the procedure described in the User s Handbook Should it be necessary to change any of the settings of the programming parameters it is possible to access Installer Level by repeating the procedure to access programming even from this level by locating the Activate password PROBLEM SOLVING ae You may find that it is not possible to programme the unit or information for some reason Some of the possible problems you may come across are listed below IT IS NOT POSSIBLE TO REPROGRAMME THE PERIPHERAL UNIT When the system requires maintenance work the Service Centre must transfer control to the installer for the tim
3. 369 and pressing OK The following display appears T 0 0 0 f 0 G 0 d 0 Q 8 The measurements which are needed to check the setting are T displays the speed in km h of the tachometer wire G displays the speed in km h of the GPS f frequency of the tachometer signal If T or G shows three instead of a number it means that there is no connection with the tachometer or GPS SC SMS NUMBER FUNCTION 374 MUST ALWAYS BE CHECKED The number of the telephone company that manages the SMS messages can be set or changed Usually new SIM cards already have the Service Centre number for SMS messages stored in their memory and therefore this number need not be altered If this number has not already been stored select the function required n 374 press OK use the keypad to key in the number taking care to add the international code press OK to confirm TESTING CONTROLS FUNCTION 375 It is possible to check if the outputs have been correctly connected before returning the vehicle to its owner Select the function required n 375 press OK HORNS INDIC BL RELAY OK The symbols mean if the minus key is pressed the horns and direction indicators will be activated if the plus key is pressed the ignition immobilisation relay and the relay for signalling immobilised status will be activated the 15 must be given to get activation Press OK to exit this function FUNCTION 378 Displays the num
4. CAR ALARM lt 5 gt Pos VOICE END OF PROGRAMMING CAR ALARM lt 5 gt Pos 03 VOICE PROGRAMMING IN OR MODIFYING VEHICLE S NUMBERPLATE MAXIMUM OF 8 DIGITS FUNCTION 307 Installer OK Select function Select function 307 OK ENTER Vehc Plate 8 chs For example key in numberplate ZZ 987 AC Press key repeatedly until letter Z O a To delete the previous number or letter lt gt To continue to the next number or letter 9 Press key repeatedly until letter Z Continue the same way for all the remaining numbers OK ENTER CANCEL CALL TRANSFER FUNCTION 215 All call transfers can be disenabled via this function deviations answering machines etc without removing the SIM card from its slot Select the function 215 and press OK Wait for the message confirming cancellation From now on all services available with the SIM card are disenabled PROGRAMMING IN THE HORN SOUND FUNCTION 323 Select function n 323 using the keypad press OK select the type of sound ALTERNATED CONTINUOUS NONE using keys and confirm selection with the OK key or press the C key to keep the previous setting PROGRAMMING IN THE TYPE OF CONTROL FOR THE DIRECTION INDICATORS FUNCTION 302 Select function n 302 using the keypad press OK select the type of control DRIVE LAMPS DRIVE BLINKER using keys
5. 2 02 of the SW onwards which can be checked using function 207 the end user can alter the unblock anti carjack and unblock functions passwords directly Therefore the 33333 factory set default password may be no longer valid In this case if the vehicle or the satellite system is to be serviced or repaired remember to ask the vehicle s owner the new functions unblock password NB Any functions displayed on the SAT PROGRAMMER which are not described in this manual refer to extension modules which provide additional features Refer to the relative instruction manuals for more details on how they work and are used 15
6. If the DOUBLE option has been selected the peripheral unit will activate the blocked status relay immediately after 15 has been turned on If the SINGLE option has been selected the peripheral unit will not activate the blocked status relay after 15 has been turned on but only if it receives the pertinent command from the Service Centre and provided the tachometer and or GPS speed is less than 1 km h Select the function required n 383 press OK and use the keys to select the SINGLE DOUBLE setting Press OK to confirm selection or C to keep the previous setting FORMAT OF COORDINATES FUNCTION 384 The type of format for the GPS coordinates can be set so that it is possible to display the geographical coordinates function 446 according to three different parameters DEGREES MINUTES SECONDS 44 42 47 N 010 36 57 E DECIMAL 44 7131 N 010 6161 E NMEA 44 42 79N 010 36 96 The type of format is important if the user intends to use map location software The position will be sent with each SMS sent to the user and the numerical format keyed in can be used to trace the position of the vehicle using a digital map Select the function required n 384 press OK and use the keys to select the DEGREES MINS SECS DECIMAL NMEA parameter Press OK to confirm selection or C to keep the previous setting PRIVATE USE OF TELEPHONE FUNCTION 401 The function enables the telephone function t
7. M module and the GPS receiver In particular it must be checked that the position of their relative antennas guarantees that the parts in question will always be able to work Follow the instructions in the CHECK GSM STATUS and CHECK GPS STATUS menus to select the best positions of the antennas on the vehicle These procedures must always be done outside at a distance from any buildings that could result in areas of shade or prevent the above mentioned parts from working PROCEDURE After the GSM antenna and the GPS antenna have been placed in the best position to guarantee optimum performance complete connections for the test connect the Sat Programmer to output n 6 on the peripheral unit using the y cable supplied in the box diagram page 1 after the GPS antenna connector has been connected to its outlet on the GPS receiver connect the connector on the GPS receiver to output n 5 on the peripheral unit connect the GSM antenna to the peripheral unit s external connector after completing the connections illustrated in the installation manual connect the connector on the main cable 16 pin to the peripheral unit reconnect the vehicle s battery The following initial message appears on the SAT Programmer s display SAT OK in maintenance The menus be displayed by pressing the arrows on the Sat Programmer menus be displayed with peripheral unit in maintenance status 1 0 Display Activate Fun
8. V808600A SAT PROGRAMMER INSTALLER S MANUAL Rel 2 02 FUNCTION OF KEYS KEYS TO ADD DATA WITH LETTERS OR NUMBERS DISPLAY MESSAGES SCROLL UP KEY TO GO THROUGH MENU FORWARDS MULTIFUNCTION KEYS gt 4 A SCROLL DOWN XQ CABLE Y SUPPLIED WITH THE SAT PROGRAMMER REMOVE AFTER COMPLETING INSTALLATION AND PROGRAM MING KEY GO THROUGH CANCEL MODIFYING DATA MENU BACKWARDS KEY TO ENTER MENU CONFIRM FUNCTIONS STORE DATA CONNECTIONS MILEOMETER SIGNAL TECHNICAL SPECIFICATIONS OF THE SAT PROGRAMMER Power supply 12 VDC Temperaturen nne a AA 30 C 85 C Cons uUMptio Nysie iaaii a aiid lt 100 mA STEP 1 Fill out the CONFIGURATION AND TEST REQUEST FORM which you will find in the peripheral unit box and send it by fax to the Customer service centre Set up the vehicle in such a way as to ensure access to all of the modules connected to the peripheral so that all alarm functions may be tested in conjunction with the service centre STEP 2 PRELIMINARY PROCEDURES FOR CONTROLLING THE SYSTEM In the initial stages of installation it is essential to check two of the principal components to ensure that the satellite system works correctly The components to be checked are the GS
9. ade of reinforced concrete low signal caused by poor coverage of the phone company Sometimes the signal from one phone company is poor whilst that of another is good If the check is being made after the initial switch on the Sat Programmer display could say GSM module in low consumption mode Press the gt key to activate the module and display the intensity of the signal RESET GSM MODULE press the lt key on the SAT Programmer to reset the telephone s GSM module Indications after the satellite peripheral unit is switched on for the first time As the peripheral unit is switched on for the first time the Sat Programmer automatically displays the acquisition of the GSM signal The displays appear in the following sequence SAT OK Maintenance mode Va N GSM signal off GSM module on J GSM serial link activating J GSM SIGNAL 0 GSM network registering GSM SIGNAL n EHEHEHEH STEP 3 SYSTEM CHECK AND PROCEDURES FOR PROGRAMMING It is possible to check that the system was installed correctly after the initial checks prior to actually completing the installation of the system Further to these checks which can be carried out with the peripheral unit in maintenance mode follow the Installer Level Entry Procedure to program the system SYSTEM CHECK Make sure that the system is powered and that all the connectors of th
10. ance mode and servicing has been completed or if the end user requests it normal operating mode can be restored Select the function required n 431 press OK Maintenance mode is now neutralised SPEED LIMIT FUNCTION 439 If the end user requests it it is possible to set the speed limit for the vehicle the peripheral unit will call the number specified by the end user the call is made if the limit is exceeded for at least consecutive 10 seconds The limit can be set from 10 to 310 Km h Select the function required n 439 press OK use the and keys to select the speed confirm selection with the OK key or press the C key to keep the previous setting 13 WARNING Remember to inform the vehicle s owner that the peripheral unit will place a call send a SMS to the numbers set in the phone book if the speed limit is exceeded This will result in an increase in the usage costs for the SIM CARD To alter the set value access the Unblock Functions Level by keying in the password 33333 or the password set by the user if it has been altered Call up the function 439 and alter the reading The vehicle owner can set the speed limit using the keypad if required by following the procedure illustrated in the User Manual or by asking the Operations Centre to do it for him STORING EMERGENCY KEYS MAX NUMBER OF KEYS THAT CAN BE STORED 3 FUNCTION 605 Connect an electronic key reading unit receptacle to
11. at reproduces voice messages to inform the end user of the causes of an alarm request or emergency situation which are listened to via the system s speaker Use the A YV arrows to locate the menu and press the A second display appears with the following message on OK to en OK Listen to the messages via the hands free speaker Press the enter Key to interrupt the sequence SERIAL NUMBER The peripheral unit s Serial Number can be consulted via the Sat Programmer This makes it possible to check the serial number at any time for communications with the Service Centre or the Manufacturer as regards assistance or updates The display shows eee key to confirm selection SN read only 000 o 00000 0000 STEP 4 ACCESSING PROGRAM MING To start the programming of the satellite peripheral unit you must enter the system at Installer Level as per the following procedure The procedure is described starting at Maintenance Level as this is the factory setting The programming steps are very important to ensure the system operates correctly and great care and attention must be paid when they are being carried out To access Installer Level you must reach user level by means of the following procedure After the peripheral unit has been switched on for the first time the display appears as follows AT OK ay Press the key to confirm selection an
12. ber of electronic keys stored in the memory Select the function required n 378 and press OK FUNCTION 380 Function 380 enables all the services present in the telephone SIM card to be deleted without having to remove it from its slot These services call transfer answering machines etc must be disenabled so that the peripheral unit can always respond directly to calls from the Service Centre Select the function required n 380 and press OK The function starts automatically and all the services activated in the SIM are disenabled 12 FUNCTION 381 Reserved for use by technical service REQUEST CODE WHEN DOOR OPENED FUNCTION 382 This function makes it possible to extend the peripheral protection if an external alarm is not connected to the Vol 1 input If the function is enabled yes the peripheral unit requires the unblock code to be keyed in either as soon as the car door has been opened or otherwise when the 15 is turned on In this case switching on the instrument panel 15 has no effect Select the function required n 382 press OK and use the keys to select the YES NO setting Press OK to confirm selection or C to keep the previous setting IGNITION IMMOBILISATION FUNCTION 383 This function makes it possible to set how the signal immobilised status relay will work when the peripheral unit is operational after 15 has been turned on and the subsequent request for the unblock code
13. ct Activate Factory Call forwarding password password disable 7 gt ae SN read only Tem disab porary disab GPS Position 0000000000000 Battery alarm 4 check h NUMBER 0 attery Check L GSM status C y mode Enable check _Listento _ NUMBER PRIVACY GPS status voice messages J L mode Disable check software relesae 1D read only GSM credit L 2 02 1 00000 Checking the GPS antenna s position check OK Use the A V arrows to locate the GPS status menu and press the ENTER to confirm selection A second display appears with the situation of the visible satellites The data shown on the display indicate Beda the number of satellites visible and their intensity For example 0 satellites visible 1 satellite visible eee re ee 2 satellites visible the first one is the strongest 15 indicates the number of visible satellites number can vary from 0 to 12 fix not avail indicates that the geographical coordinates of the position have not been calculated This indication normally corresponds to the first time the peripheral unit is switched on when the satellites are not yet visible current fix indicates that the visible satellites are able to calculate the position of the vehicle and the position data
14. ct the function required n 362 press OK select the type of polarity POSITIVE NEGATIVE with the and keys confirm selection with the OK key or press the C key to keep the previous setting SETTING THE HANDS FREE KIT FUNCTION 364 It is possible to configure if a hands free kit is connected or not Select the function required n 364 press OK use the and keys to confirm if there is a hands free option or not YES NO confirm selection with the OK key or press the C key to keep the previous setting CALIBRATION OF TACHOMETER FUNCTION 368 With version 2 02 the tachometer calibration is done automatically However calibration as described below is recommended to check that the mileometer signal gives the correct reading Calibration must be checked when the system has been completely connected up powered and the vehicle is ready to go back on the road After connecting the mileometer wire the correct operating frequency for the vehicle s mileometer must be stored in the peripheral unit s memory Select the function required n 368 press OK start up the vehicle and reach the speed of 50 km h keep this speed steady and press OK to confirm If the tachometer is not connected up the SAT Programmer s display will inform you Tachometer not connected CHECKING GPS SPEED FUNCTION 369 It is possible to check the calibration of the tachometer speed whether automatic or manual by selecting the function required n
15. d then In uae Jis displayed Use the A V keys to select the Activate Funct password GSM SIGNAL n SSB N J display and press the key to confirm selection There next appears the display with PASSWORD ACTIVE Insert password _ press key 3 five times and confirm with the next display XQ OK Functions active PASSWORD OK a 61010 th k then select function Key the number and confirm by pressing the enter key The display appears with age OK Activate Instal confirm by pressing the enter and continue password of PASSWORD ACTIVE OK L_ Insert password Press key 4 five times and confirm with the ENTER key The next display confirms that you have reached installer level as follows _InstallerOK Select function It is now possible to decide how to proceed with the programming of the peripheral unit but in both cases it is essential to take great care with programming The methods for programming are as follows OK use the Y keys to select the function or functions of interest and then press the ENTER key to access the selected function call up the function of interest by keying in its corresponding number and then press the KUA key to access the selected funct
16. distinguished by Latitude and Longitude Warning check what type of coordinates accepted if they are to be inserted in map software Function 384 can be used to set the display format of the coordinates to DECIMAL or NMEA It is normal that the display of the minutes varies during the display of the position data unless this variation is 2 units Ox indicates that updated geographical coordinates are currently being received If this symbol is absent it indicates that the coordinates are not updated and are previous to the reading If this symbol is absent it does not mean there are problems with reception Any doubt must be cleared up by checking with the Check GPS Status menu 45 46 05 N indicates the Latitude of the geographical position which is N North if you are above the equator and S South if you are below the equator key to exit the GPS Position 008 48 52 indicates the Longitude of the geographical position which is E east if you are to the right of the Greenwich meridian and W west if you are to the left of the Greenwich meridian OK Press the key to exit the function BATTERIES CHECK The peripheral unit provides information on the status of the vehicle s battery and its own internal battery Use the AA V arrows to locate the Battery Check menu and press the key to confirm selection A second display appears wit
17. e external appliances are connected up correctly Also make sure that the SIM phone card is inserted in the correct slot Check the status of the GPS and GSM signal again as previously described DISPLAY OF INPUTS OK Use the V arrows to locate the _ I Display menu and press the key to confirm selection A second display appears with the status of the inputs The first display that appears is as follows R indicates that the peripheral unit is under the installer s control The display is updated every time the peripheral unit receives a stimulus for example Switch the dashboard on 15 the display is updated K indicates that the ignition key is inserted and operational Switch the dashboard off the display is updated tees dashboard off The same tests can also be made with the other available input lines SMHVARYXDT12BKGC dashboard off where the letters in combination with the descriptions indicate Letter If the letter is shown on the Display If the letter is not shown on the Display Letter__ If the letter is shown on the Display If the letter is not shown on the Display 5 Signals active Signals off X Crash sensor triggered Crash sensor at rest M Peripheral unit is immobilised Peripheral unit is not immobilised 2 Doors open Doors closed H Peripheral unit is active Peripheral unit is neutralised Boot open B
18. e needed for the work to be done This mode of operation is called MANAGEMENT MODE and the installer must always make sure that the Service Centre has activated Control from SC to Installer 14 THE MILEOMETER SPEED IS NOT SHOWN ON THE DISPLAY Check that the wire is connected up correctly and that the signal is taken from the correct wire Usually the mileometer signal is alternating with voltage up to 12 volt for vehicles and the frequency varies with the variation of the speed The signal is normally given when the instrument panel is switched on THE GPS SPEED IS NOT SHOWN ON THE DISPLAY Check that the GPS receiver antenna is connected up correctly IT IS NOT POSSIBLE TO ACCESS INSTALLER LEVEL AFTER THE SYSTEM HAS BEEN TAKEN UP BY THE SERVICE CENTRE SAT If the SAT Programmer displays maintenance SC the SC symbol means that the peripheral unit is in maintenance mode but is still controlled by the Service Centre Call the Service Centre to inform them of the problem and get installer control If control is transferred correctly the next SAT OK display will be in maintenance If you attempt to access Installer Level by following the procedure for Access Programming STEP 4 from user level SAT OK Service Centre o and the display indicates Management for a moment you must request authorisation for access from the Service Centre as described above From version
19. h the status of the batteries Int 7 2V 423 C Ext 14 5V ok OK The data should be read as follows Int voltage inV the internal battery s voltage temperature in C the internal temperature of the peripheral unit Ext voltage in V the external battery s voltage ok indicates that the external battery voltage is correct off together with 0 0V indicates that the vehicle battery is disconnected nok together with a voltage reading below 10 0V indicates that the voltage of the vehicle s battery is too low to safeguard the correct running of the system OK indicates which key to press to exit the display Flashing symbols appear next to the Int voltage in V which indicate if the internal battery charging system is operating and if it is charging the internal battery The internal battery is only charged if external battery voltage is above 10V external temperature shown on the display is above 0 C and below 80 C 15 is ON The flashing symbols with 15 on should be read as follows internal battery charged and system at rest internal battery is flat and system in rapid recharge mode internal battery sufficiently charged and internal recharge system in slow recharge mode If 15 is not on only the symbol flashes regardless of the level of internal battery voltage displayed Press the key to exit the function LISTENING TO VOICEBOX MESSAGES The system is provided with an internal synthesizer th
20. hanged For example 1 i 1 ENTER For example add the phone number For example delete the phone number already 393481234567 at position 1 stored at position 1 e g 393483456789 Index 1 Index 1 gt gt available lt lt 393483456789 9 1418 1 lt Index 1 393481234567 To delete the selected kam Press position in the memory ENTER twice PROGRAMMING THE CALLS LIST FUNCTIONS FROM 342 TO 357 For example List of Car Alarm calls calls to the end user due to external alarm 10 Installer OK Select function Select function 353 OK ENTER Call List editor CAR ALARM OK ENTER CAR ALARM cause of call lt I gt index of numbers to call max 5 Pos position in the phonebook CAR ALARM lt 1 gt VOICE ONLY type of call Pos VOICE ONLY VOICE SMS SMS VOICE VOICE SMS of the memorised number max 90 For example call number stored in phonebook at position 1 CAR ALARM lt 1 gt Pos 01 VOICE ONLY Does the phone receive SMS YES NO AV VOICE Leave SMS VOICE SMS VOICE VOICE SMS Call another number in the phonebook For 03 in the phonebook index NO YE N ae 5 ENTER
21. ion The table below lists the functions which are available for the installer The table shows the function s number the symbols that appear on the display the factory setting if any and a short comment by way of explanation Function N Symbols on the Factory setting Description display 200 Unlock 11111 The code used by the Code gt gt end user for disarming 201 Anticarjack The code used by the end user Code gt gt in case of car jacking 202 Functions Enable 33333 The code used to access Code gt gt programming functions Index phone numbers 0000000000000 number 207 he oa release Release of factory i oan XX XX set software 211 Temporary disab _ selected temporarily disenables Battery alarm the alarm for disconnection of battery for one arming cycle 212 NUMBER PRIVACY If selected does not let your mode Enable number be displayed in case of calls 213 NUMBER PRIVACY If selected lets your number of calls 214 ID read only Recognises the identification number 00000 of the peripheral unit memorised by the Service Centre 215 Call forwarding Allows call transfer services to disable be disabled 300 Installer Code 44444 The code for access gt gt 44444 at your level DRIVE LAMPS controlled directly or not 307 8 chs vehicle s numberplate alarm ALTERNATE is controlled if an 341 GSM Call activ Time bet
22. is constantly updated previous fix indication given after current fix In this case the system has already acquired the coordinates that are not updated as the vehicle is in an area of shade and no longer receives signals from the satellites No GPS indicates that the GPS receiver has probably been disconnected or that there is a fault N indication given in seconds of the time passed since the selection of the Check GPS status function The time required to acquire the minimum satellites for the first calculation of position in conditions of visible sky meaning there are no obstacles near the vehicle e g very high buildings is around 300 seconds The timer goes back to zero every time you press the OK key and thus exit check mode and starts again when you access the function again The timer stops when it reaches 999 and is not updated The timer is not a critical factor for acquiring satellites but is just an indication of how much time has passed Possible problems when acquiring satellites Vehicle N Satellites Indication on Time passed Type of fix Notes Position the display Open sky From 0 tol eee 600 sec No fix available Move GPS antenna Garage From 0 to 1 eer nner 600 sec No fix available Move vehicle outside Open sky 0 always No GPS Check connection of GPS receiver and control unit Open sky O always No fix available Check connection of GPS or previous Fix antenna to
23. numbers in phonebook can be made after activation 42 Extern alarm 5 minutes Delay after placing CAR ALARM immunity 5 min calls if VOL1 is active wo 430 maintenance mode Puts the peripheral unit Enable into maintenance mode 431 maintenance mode Takes the peripheral unit out Disable of maintenance mode 439 Speed limit 310 Kmh Sets the maximum speed the 31 310Kmh peripheral unit calls if this is exceeded 446 GPS Position Displays the geographical coordinates of the vehicle s position 447 Display I O Displays the status of the inputs and outputs 460 ee TT Displays Greenwich time as reference 20may02 10 00 00 for reception of GPS signal password Electronic Keys electronic keys 606 Add Adds extra keys in addition Electronic Keys to those already stored Some of the most important programming functions are illustrated below and the simpler and less significant steps are described in the written comments The keypad is used to carry out all the programming together with the use of the AVY arrow keys and the lt p gt function modification keys Refer to the pertinent section at the end of the manual on how to exit programming mode PROGRAM MING PHONE NUMBERS IN THE SIM CARD S PHONEBOOK FUNCTION 205 Installer OK Select function 205 Phonebook Edit select another number in the phonebook Key in the index number to be 1 c
24. o be used via the on board keypad If set as DISENABLED the telephone will not work if full telephone numbers are keyed in However all the numbers stored in the phone s memory can still be called e g 01 and 99 to call the Service Centre Incoming calls are always possible Select the function required n 401 press OK and use the keys to select the ENABLED DISENABLED parameter Press OK to confirm selection or C to keep the previous setting EXTERNAL ALARM IMMUNITY FUNCTION 429 The amount of time that the peripheral unit will disregard further triggers of an external alarm on the VOL1 input can be changed from 1 to 15 minutes if set Zero indicates that no immunity time has been set We do not recommend you alter the factory setting Select the function required n 429 press OK use the keys to modify the setting confirm selection with the OK key or press the C key to keep the previous setting HOW TO ENTER MAINTENANCE MODE FUNCTION 430 When the vehicle is being serviced or should the end user specifically request it the peripheral unit can be put into maintenance mode In this mode the normal functions of the peripheral unit are temporarily neutralised and an alarm will not be triggered if the vehicle s battery is disconnected Select the function required n 430 press OK Maintenance mode is now operational HOW TO EXIT MAINTENANCE MODE FUNCTION 431 When the peripheral unit is in mainten
25. oot closed V Handsfree active Handsfree at rest 1 VOLI active VOLT at rest A Peripheral unit enabled Peripheral unit in maintenance mode 2 VOL2 active VOL2 at rest R Installer control Service Centre control Bonnet open Bonnet closed Dashboard on Dashboard off Y Transport mode active Transport mode neutralised G Window open Window Closed Sunroof open Sunroof closed NB the information displayed is updated after the status of an input changes No information is displayed for the first input after the check function The consecutive sequence with the variation of several inputs makes it possible to display the last variation alone The previous ones are not displayed unless the variation in question is repeated OK Variation in the crash sensor is not immediate as it is delayed for a few seconds Press the ENTER function GPS POSITION If the peripheral unit can see the sky correctly and more than 3 satellites are visible which guarantee the establishment of the Current Fix it is possible to interrogate the GPS Position function to display the geographical coordinates of the vehicle s position OK Use the A VY arrows to locate the menu and press the ENTER key to confirm selection second display appears with the geographical coordinates of the vehicle s position 45 46 05 N The geographical coordinates are set by the manufacturer in degrees minutes and seconds and 008 48 52 OK are
26. peripheral n 3 and store the keys Select the function required n 605 press OK insert the keys to be stored in the reader s memory one at a time the number of keys stored at bottom right increases by the number of good keys inserted press OK again to exit this function Any keys previously stored will be deleted by this process The peripheral unit s maximum waiting time for the insertion of a key is 20 seconds FUNCTION 604 Reserved for use by technical service ADDING EMERGENCY KEYS FUNCTION 606 This function makes it possible to store new keys in addition to those already stored and does not delete those stored previously Select the function required n 606 press OK insert the keys to be stored in the reader s memory one at a time the number of keys stored at bottom right increases by the number of extra keys compared to the number at the beginning press OK again to exit this function The peripheral unit automatically exits the function 5 seconds after the last key has been stored HOW TO EXIT PROGRAM MING Installer OK OK To exit programming starting from the Select function display press the zero key ENTER The peripheral unit returns to its initial status and displays SAT deactivated in maintenance OK Restore the peripheral unit to its in maintenance _Jstatus by pressing key LL five times and then pressing the key ACTIVATING THE PERIPHERAL UNIT
27. the following display ERROR SIM CARD ad insert PUK REQUIRES PUK this display alternates with restart Select the key on the Sat Programmer the display changes to INSERT PUK If the PUK is correct the following display appears PIN DISABLED When the correct PUK is keyed in the PIN code is automatically changed to 1111 and consequently neutralised After the correct PUK is keyed in the display automatically changes over to show the status of the GSM signal If this is not ee GSM status OK visible use the AV arrows to locate the verify menu and press the ENTER key to confirm selection A second display appears which shows the status of the GSM signal GSM SIGNAL n The data provided indicates f 5 the percentage of GSM signal that is available This is the effective signal that is available and should not be compared to the signal shown on the display of a mobile phone as this only gives an approximate reading Chart giving a visual indication of the available GSM signal If the percentage amount and the chart indicate a very low signal it is important to locate the causes preventing good reception These may be e antenna is in critical position antenna is not connected to the outlet on the control unit antenna cable is damage or partially broken the vehicle is located in a garage m
28. the receiver CHECKING THE GSM ANTENNA S POSITION Before checking the GSM signal a SIM phone card must be inserted into the dedicated slot This must not have an access PIN number message box service or incoming call transfer service The SAT Programmer indicates if no SIMCARD is present with the following message ERROR SIM CARD The telephone continues its attempts to locate the SIM Card which is automatically recognised as f NOT FOUND soon as itis inserted in the appropriate slot The SAT Programmer can be used to eliminate the PIN if it has not already been deleted from the SIM Card The peripheral unit recognises that the PIN is present and allows it to be neutralised ERROR SIM CARD PIN insert PIN REQUEST this display alternates with Restart Select the key on the Sat Programmer the display changes to INSERT PIN Key the correct PIN and press OK to confirm If you make a mistake press to repeat F Function active If the PIN is correct the SAT Programmer first displays Please wait CODE OK PIN DISABLED J and then the telephone is automatically started PASSWORD If the PIN is not correct the Sat Programmer displays NOT ACCEPTED Please remember that the SIM will be blocked if three attempts are made to key in a false PIN and also that the PUK must be keyed in after the third attempt as per
29. ween cause and call delay 10 can be set between 0 and 254 secs SPEED WARNING limit is exceeded LOW BATTERY battery is flat LOW CREDIT Only with prepaid SIM card credit is insufficient CAR ALARM car alarm sounds PERIODIC Service Centre with programmed period voice messages message via hands free 362 VOL 1 input pol Programmes in the polarity POSITIVE of the VOL1 input 36 Hands free set Programmes in the presence Present YES of the hands free kit x GSM module GPS module of prepaid SIM phone cards 368 Speedometer Must be calibrated Memorises the frequency of Calibrationr the speedometer signal 369 GPS Speed Must be checked Displays the tachometer internal and vehicle batteries at_50 units value of prepaid SIM phone cards 374 SC SMS Number Already stored or Indicates the number of the to be stored by SIM phone company for SMS messages 375 For checking horn output and blinker connections and immobiliser 378 Electronic keys ODisplays how many electronic keys in memory are stored in the memory of the peripheral unit 381 Update data Seve Only for use by technical service format 382 Code request at Activates request for unblock code doors open NO when door is opened 383 Ignition block DOUBLE Activates aux relay even if not blocked by remote Set single if fault with check panel 384 DEGREE MIN SEC Sets format of coordinates via SMS to DEGREE MIN SEC user 401 Outgoing Calls ENABLED If disabled only calls to
Download Pdf Manuals
Related Search