DXE-CAT-RX3 Series User Guide
Contents
1. Receives HDMI up to 1080p 60Hz 24bit 600ft over one CAT 6A Shielded cable HDCP Compliant 2x35 Watt Amplifier A Version Differential Line Input Output for Audio Mixing amp HDMI Audio De Embedding Volume Control Audio Functions Remotely Controlled via Transmitter Unit or Optional IP IP Control Engine C Version Bi directional RS 232 amp IR amp LAN Two Relays for Screen Control Rear Mounted Connectors for Clean Installation Status LED for All Connections on Front Refer to Technical Specifications Section Warning Do not plug RJ 45 HDBaseT output to non HDBaseT complaint devices or damage may occur to either product User Guide Front Panel DXE CAT RX3 SERIES DO DXE CAT RX3 IROut TX HDBT Power Aurora a EE aa ed Front LED Indicators IR Out Blinks when emitting IR to device from IR Port It is normal to be lit if nothing is plug into IR port IR In Blinks when receiving IR from IR port It is normal to be lit if nothing is plug into IR port TX RS 232 Transmit Blinking rate and intensity will vary with baud rate RX RS 232 Receive Blinking rate and intensity will vary with baud rate HDBT Lights when HDBaseT RJ 45 has proper connection between an RX TX pair Blinks when in sleep mode HDMI Will light solid if HDMI is plugged in on both RX TX and HDCP is present If no HDCP LED will blink POWER Lights green when power is present STATUS Will b2. Enter the IP address the variable is to be sent to an Aurora control device Note the IP address overrides the Master Remote IP address Target RPC Variable Name Enter the variable utilized by the remote control processor 14 Port Settings Telnet Server DXE LXC Master Remote IP Local Serial Port 1 Settings Port Processing Session Test Serial Transmit Remote Serial Port 2 Settings Port Processing Session Test Serial Transmit User Guide aa URORa Multimedia DXE LXC Port Setup 0 0 Baud Rate Data Size Parity Stop bits Telnet Server X Telnet Local Port Number Telnet Timeout Seconds Telnet Protocol Baud Rate Data Size Parity Stop bits Manual Activate IR repeater mode 115200 8 None ME Serial Test 115200 Telnet Local Port Number Defaulted to Port 23 but can be changed to other port numbers Telnet Timeout Seconds Defaulted to no timeout but can be set to timeout and close the connection Telnet Protocol Default is Telnet otherwise it can be set to none which is used for TCP 15 User Guide Port Settings Telnet Client m ORAM a ltimedia DXE LXC DXE LXC Port Setup Master Remote IP 0 0 Local Serial Port 1 Baud Rate 115200 Settings Data Size 8 Parity None Stop bits 1 Port Processing Session Telnet Client y Remote Session IP Address i JTI Telnet Remote Port Number 23 Telnet Local Port Number
3. the other serial port Test Serial Transmit Enter a serial string to send out the RS 232 port for testing of connecting device IR Ports Selecting the activate IR repeater mode enables the transfer of the IR ports signals to and from the TX and RX units If it is not selected only RPC Telnet TCP commands will trigger the IR ports locally or remotely IR files are stored on the ftp of the DXE CAT RX3C RX3C A unit in the IR folder 12 Port Settings Manual DXE LXC 0 19 Baud Rate Data Size Parity Stop bits t2 Baud Rate Data Size Parity Stop bits Manual Activate IR repeater mode User Guide w URORA Multimedia With port processing session set to manual there will be no additional selections as the system is set to trigger the functionality with IP commands Ports will not pass data from the TX to RX and vice versa in this mode 13 User Guide Port Settings Push to Variable w URORa Multimedia DXE LXC DXE LXC Port Setup Master Remote IP 9 Local Serial Port 1 Baud Rate 115200 Settings Data Size 8 Parity None Stop bits Push to Variable Remote Session IP Address 168 J Target RPC Variable Name serlvar Test Serial Transmit Serial Test Remote Serial Port 2 gaud Rate Settings 5 Data Size Parity Stop bits Port Processing Session Manual Test Serial Transmit Activate IR repeater mode Remote Session IP Address
4. 192 168 1 10 setup The default user name is admin and the default password is admin In the event you lose your settings press and hold the setup button on the DXE CAT RX3C RX3C A for 3 seconds This will restore the unit back to factory default Usage Only serial port 1 will be used to communicate to the RX3 at a baud rate of 115200 This baud rate will be fixed but the ports for the RX3 must still be set up accordingly to the correct baud rate to match the device they are connected to The 30PTL x lt cr gt command must be sent first to pick which port 1 HDBaseT or 2 Local RS 232 before sending a serial command out a port General Settings DXE LXC User Guide za UR ORE Viultimedia DXE LXC Current Settings Status Change Password Reset Factory Defaults Firmware Update Mode Restart DXE LXC IP Address 192 168 1 10 Hostname DXELXC MAC Address 00 11 02 b0 00 00 Serial Number 00000000 Firmware Revision 99 08 Enter new password Verify new password Change Password Restore Defaults Force Update Status Shows the current IP Address Hostname Mac Address Serial number and the firmware revision Change Password The default password is admin It is recommend to change the password for better security on the network especially if it is not private Reset Factory Defaults Once pressed a confirm screen will appear Once confirmed the unit will restore the defau
5. FCC This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interferences received including interference that may cause undesired operation Trademarks All trademarks in this document are the properties of their respective owners User Guide TABLE OF CONTENTS PACKAGE CONTENTS siia EE OE ER NE OE aaaea 2 INTRODUCTION Sessie Si ee n ek De N GR Ek ek SR de Gun n N END OE N N ER ee N SEUN N Di OE SN EN SUE 3 Nood AE ELE EE EE ER AE EE OE OE 3 ARE N OE ER EE OE EE ER EN 4 Front Panel DXE GAT RX3 SERIES eien ities a dee BE Se ve eek ee ee dee ee ee GEN ge eek eed ie 5 Rear Panel DXE CAT RX3 SERIES sesse dees Se Gede Se esse el pa se eek ke KERE GN aa daaa aa DUN Be Eg Ged k egg d eg dees 6 IR EXTENDERS rniii oe SeSe eek bee ee We Vele ee ede ed de ee EDEN RE ene De OO ee Ee ee ee Eike ede ee 7 IR GOMMOCUONS ER EE ade te 7 IR Jack Pinout N EE EE EA N 7 IP SETUP ME EE ER OE 8 VNC UL CE OIA AE OR RE OO RE HEER OR AE EE 8 RYE ed EE RE RE OR EE N 8 eel ES uie ER ES EE RE OE EE EE OE EE EE ER OE 9 NetWork SENINGS EE EE OE ER OO OO aTe aana EaI E 10 edele EN 11 selndelsuesiedd ENGER OR N OR OE OE divieeeeeeda ates 13 Port Settings Push to Variable si ss EERS Ee ae Pe ER EN Gee Me Ee ea be ee ee ai be ee GEN ee Ee Au OK ee ee ve we be MEE Ek ee 14 Port Settings Telnet Server iss EE EE a a eli Das ee de
6. Long Reach Mode CAT 6A CAT 5e 6 will achieve 328ft 100m for pixel clock lt 225MHz CAT 5e 6 will achieve 230ft 70m for pixel clock gt 225MHz CAT 6a 7 will achieve 328ft 100m for pixel clock gt 225MHz LAN Connectors Dual 8P8C with 2 LED indicators each HDBaseT Connector RJ 45 WE SS 8P8C RS 232 Connector 3 5mm TRS IR Connector 3 5mm TRS Auto Sensing Direction for Blaster or Receiver HDMI Connector Type A 19 pin Power Connector 2 5mm ID Half Twist Kycon Relay Connector 3 81mm Euro Style Green 4 Position Line In Out Dual 3 81mm Euro Style Green 5 Position Amplifier Connector 5 08mm Euro Style Green 4 Position Mechanical DXE CAT RX3 Series Housing Black Aluminum enclosure Dimensions L x W x H 130mm x 55mm x 30mm 8 46 x 3 82 x 1 3 weg Mounting Wall mounting amp Rack Mounting Power supply 24 90 Watt DC Only 1 required on RX for Amplifier model 132mmx57mmx31mm Power consumption 5 Watts Typical 80 Watts Amplifier full use Max Operation temperature 0 40 C 32 104 F Storage temperature 20 60 C 4 140 F Relative humidity 20 90 RH no condensation 27 User Guide 1x DXE CAT R x x 3 3C 3 A 3C A accordingly 1x 24V DC 90 Watt Wall Supply for A models only Non A models can be powered Package Contents through normal means and must be ordered accordingly 1x DXE CAT E1 Wall Desk Mount Ears with Screws 1x User Manual IR Receiver 38KHz CA00
7. 120 78dB to OdB Response 30LVLx lt cr gt Query Line Out Volume 30LVL lt cr gt x 0 9 1dB steps OdB to 9dB Query Amplifier Response 30AVLx lt cr gt Volume 30AVL lt cr gt x 0 9 1dB steps OdB to 9dB Query LAN Serial Port Response 30PTL x lt cr gt Select 30PTL lt cr gt X 1 or 2 1 HDBT 2 Local Serial Port Note 30 after or is the product fixed address 20 User Guide IP COMMANDS TCP RPC Commands Remote procedure calls RPCs are used to control the DXE CAT RX3C RX3C A from any device with a web browser PC iPad touch panel etc an external control system or another web enabled device RPCs can be used to send serial and IR commands receive serial data and retrieve system information RPCs can be sent in the form of an HTTP POST used for web based control pages or control from an Aurora WACI series controller or TCP commands used for control from an external control system Calls to the RPC server using HTTP POST are done through the rpc virtual directory e g http ip address rpc Use this directory as part of the URL when creating the address for the HTTP POST Transaction TCP commands are structured the same way as the HTTP POST but sent over a raw TCP connection without any HTTP headers Command Description Serial_GetSettings Port Returns the settings of a specific serial port 1 Sends a serial command to a specific port 1 2 Serial_Send Port Msg Ma
8. DXE CAT RX3C RX3C A The Flash export from YIPI will only work with NX or QX series at this time 23 CONNECTOR PIN HDMI Pin 1 TMDS Data2 Pin 2 TMDS Data2 Shield Pin 3 TMDS Data2 Pin 4 TMDS Data1 Pin 5 TMDS Data Shield Pin6 TMDS Data1 Pin 7 TMDS Data0 CAT5e 6 7 Pin T568A Pair T568B Pair Wire 1 J 2 tip 2 3 2 ring 3 2 3 tip 4 1 1 ring 5 1 1 tip 6 2 3 ring 7 l4 4 tip 8 4 4 ring User Guide DEFINITION 19 17 168 13 11 9 18 16 14 12 10 8 Type A Receptacle HDMI Pin8 TMDS Data0 Shield Pin 15 SCL Pin9 TMDS Data0 Pin 16 SDA Pin 10 TMDS Clock Pin 17 DDC CEC Ground Pin 11 TMDS Clock Shield Pin 18 5 V Power Pin 12 TMDS Clock Pin 19 Hot Plug Detect Pin 138 CEC Pin 14 Reserved N C on device T568A and T568B Wiring T568A Color T568B Color Pins on plug face socket is reversed white green stripe white orange stripe 1 TD f f oa Pin Position green solid orange solid f white orange stripe white green stripe Do mm blue solid blue solid white blue stripe white blue stripe 9 EED orange solid green solid white brown stripe white brown stripe brown solid brown solid 24 User Guide APPENDIX 1 Troubleshooting Problem Solution a Check that the power plug is properly inserted into a functioning power outlet b Make certain source is on c Verify pin out of conne
9. ge ee ee GE alia alee 15 Port Settings Telnet Client ee ee AR ee AR AR ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee 16 Por Setings Pushto POM EE RE ER EE EE OE ei 17 Port Settings Pass Through siese Re NE ERA EE GR GEE ER ee E ER Ao ee Re A RES GEE N 18 SERIAL COMMANDS ei su ae uses seker eie enge Mossop eek eo ee kon koe ea iaaa 19 RS 232 Commands ee ee ee AR ee AR AR AA Re AR ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee 19 IP COMMANDS 5 use sere se ie ee ge ie ui ee be eu be ee ee Ge Se ge ee oe Due ee ee 21 TCP RPC Command RE N EE EE ER EE EE 21 TEPARPG Command Usage sr im ed ian oek Ee da ten eb RE Ged DER eh deta ch he het Ee ORE Ge dee 22 WEB SERVER EE N SE OE OE Ee EE ORN 23 CONNECTOR PIN DEFINITION eise esse ends see eo ee ee ee Ge ee ge eg ee ei ee 24 gel RE OR OE EE OR EO ER EE ER ER 24 ME RE EO lausuvensagcubandadduucdadgawend csudeeedgacexsadasdsdhadguexstaxudevaadedale 24 APPENDIX 1 Traubli sHOoUmO sissies sesse ae Ed ee si De ek se Ge bi GN Ede ed 25 APPENDIX 2 Firmware Update ieke iese EES WENE R ER RR Ee EE REEN ER ER SEN e Ee DA EE RR GE Wi Ne ee EE EE EER kende ED 26 APPENDIX 3 Technical SpecificationS susse eek ee EER RR RR AA REG GAAR E RR RR ee AA Re Ge EER RR ee Re Rea ea 27 APPENDIX4 Cabling siese ds ee ds nan ee Ede N Ged Ge ed Ge de ei ed ge ed Ge eg EK Se 29 APPENDIES Warianty osse sesse deed de ao ve de de da ea ed ea od ve ko ed Ki bo ee EN ee 30 User Guide PACKAGE CONTENTS Please
10. make sure the following items are included within your package Contact your dealer if any items are missing or damaged DXE CAT RX3 DXE CAT RX3C DXE CAT RX3 or DXE CAT RX3C x 1 DXE CAT E1 Wall Desk Mount Ears x 2 Note Power supply sold separtely unless ordered as a set with transmitter package DXE CAT RX3 A DXE CAT RX3 SERIES DXE CAT RX3 A or DXE CAT RX3C A x 1 DXE CAT E1 Wall Desk Mount Ears x 2 PS0077 1 24V DC 90 Watt Power Adapter x 1 Optional Accessories PS0053 1 or PS0080 1 24v DC 15 5 Watt power Supply PS0062 1 24v DC 24 Watt power Supply IR Receiver CA0026 1 IR Emitter CA0012 1 Ed IR Blaster CA0049 1 RS 232 Adaptor 3 5mm TRS to FEMALE DB9 2 TX 3 RX CA0052 F2T3R RS 232 Adaptor 3 5mm TRS to FEMALE DB9 3 TX 2 RX CA0052 F3T2R RS 232 Adaptor 3 5mm TRS to MALE DB9 2 TX 3 RX CA0052 M2T3R RS 232 Adaptor 3 5mm TRS to MALE DB9 3 TX 2 RX CA0052 M3T2R MPNA Note Go to www auroramm com for latest manual and firmware 2 User Guide INTRODUCTION About The DXE CAT RX3 DXE CAT RX3 A DXE CAT RX3C amp DXE CAT RX3C A are a part of the growing Digital Xtreme Series This product is different than the typical CAT extender found on the market today as it not only breaks the price barrier but the feature and usability aspects as well Rear mounted connectors provide for a clean professional installation The DXE CAT RX3 Series is designed to complement the Digital Xtreme Series of HDBaseT transm
11. 23 Telnet Timeout Seconds 0 Telnet Protocol Telnet Test Serial Transmit j Serial Test Remote Serial Port 2 Baud Rate 115200 Settings Data Size oY Parity None Stop bits ds Port Processing Session Manual Test Serial Transmit Serial Test Remote Session IP Address Enter Telnet Server IP Address Telnet Remote Port Number Defaulted to Port 23 but can be changed to other port numbers Telnet Local Port Number Defaulted to Port 23 but can be changed to other port numbers Telnet Timeout Seconds Defaulted to no timeout but can be set to timeout and close the connection Telnet Protocol Default is Telnet otherwise it can be set to none which is used for TCP 16 User Guide Port Settings Push to Port DXE LXC Master Remote IP Local Serial Port 1 Settings Port Processing Session Test Serial Transmit Remote Serial Port 2 Settings Port Processing Session Test Serial Transmit _ w ROR Multimedia DXE LXC Port Setup Baud Rate 115200 Data Size 8 Parity None Stop bits PushtoPort Remote Session IP Address Target RPC Serial Port Number Serial Test Baud Rate 115200 Data Size 8 Parity None Stop bits 1 ed Manual Activate IR repeater mode Remote Session IP Address Enter IP address of serial port on another Aurora control device to target This will forward the serial data to any Aurora control system product It overrides th
12. 26 1 IR Emitter CA0012 1 Specifications subject to change without notice 28 User Guide APPENDIX 4 Cabling Aurora extender products have been tested utilizing shielded cabling Although our products will work fine without shielded cable it is highly recommended for environmental reasons as the signals are high frequency and can radiate as well as be susceptible to external frequencies and possibly cause noise or disruption in the image Unshielded cabling will work fine in a conduits as it will provide the shielding We have found not all cable is created equal even though they appear similar This can affect distance and overall performance Below is a list of cables that have been officially tested with our products by the manufacturer of the cable West Penn Wire CAT 6 Shielded HDBaseT Certified Only in Black 4246F CMR 254246F CMP Plenum CAT 6a Shielded HDBaseT Certified Only in Black 4246AF CMR 254246AF CMP Plenum Both CAT 6 and CAT 6a Shielded Cables utilized a Modular Plug Kit 90170 BI Includes 100 Connectors 100 Boots Crimp Tool External round Crimp Tool Strip Tool CAT 6 Unshielded Colors 4246 CMR 254246 CMP Plenum Connector 32 6EZP CAT5e Shielded Blue or Gray 4245F CMR 254245F CMP Plenum Connector 32 EZSTP CAT 5e Unshielded 12 Colors 4245 CMR 254245 CMP Plenum Connectors 32 EZP 29 User Guide APPENDIX 5 Warranty Limited 3 Year W
13. a Size 8 Parity None Stop bits 1 Port Processing Session Manual Push to Variable Test Serial Transmit Push to Port Serial Test Telnet Client F i Telnet Server Remote Serial Port 2 Pass Through 115200 Data Size 8 Parity None Stop bits 1 Port Processing Session Manual Test Serial Transmit Serial Test IR Ports Activate IR repeater mode ___ Apply Changes Master Remote IP Enter the Aurora control system IP the DXE LXC is going to push information to Note If an Aurora control system is not used RPC Telnet or TCP is available Local Serial Port 1 Settings Baud Rate Date Size Parity and Stop bits are selected for the TX RS 232 port Remote Serial Port 2 Settings Baud Rate Date Size Parity and Stop bits are selected for the RX RS 232 port 11 User Guide Port Processing Session Choose between the following modes of operation Manual Ports are just serial ports manipulated via RPC Telnet TCP commands Push to Variable RX data is pushed via Aurora RPC to given Master Remote IP Push to Port RX data is pushed to given IP remote serial port via Aurora RPC Telnet Client Unit will attempt to connect to given server IP and pass and receive serial port data Telnet Server Unit will wait for external connection to pass and receive serial port data Pass Through Unit s TX RX serial ports are linked so any serial RX data will come out the TX on
14. arranty Aurora Multimedia Corp Manufacturer warrants that this product is free of defects in both materials and workmanship for a period of 3 years as defined herein for parts and labor from date of purchase This Limited Warranty covers products purchased in the year of 2009 and after Motorized mechanical parts Hard Drives DVD etc mechanical parts buttons doors etc remotes and cables are covered for a period of 1 year Touch screen displays are covered for 1 year touch screen overlay components are covered for 90 days Supplied batteries are not covered by this warranty During the warranty period and upon proof of purchase the product will be repaired or replaced with same or similar model at our option without charge for parts or labor for the specified product lifetime warranty period This warranty shall not apply if any of the following A The product has been damaged by negligence accident lightning water act of God or mishandling or B The product has not been operated in accordance with procedures specified in operating instructions or C The product has been repaired and or altered by other than manufacturer or authorized service center or D The product s original serial number has been modified or removed or E External equipment other than supplied by manufacturer in determination of manufacturer shall have affected the performance safety or reliability of the product F Part s are no longer availa
15. ble for product In the event that the product needs repair or replacement during the specified warranty period product should be shipped back to Manufacturer at Purchaser s expense Repaired or replaced product shall be returned to Purchaser by standard shipping methods at Manufacturer s discretion Express shipping will be at the expense of the Purchaser If Purchaser resides outside the contiguous US return shipping shall be at Purchaser s expense No other warranty express or implied other than Manufacturer s shall apply Manufacturer does not assume any responsibility for consequential damages expenses or loss of revenue or property inconvenience or interruption in operation experienced by the customer due to a malfunction of the purchased equipment No warranty service performed on any product shall extend the applicable warranty period This warranty does not cover damage to the equipment during shipping and Manufacturer assumes no responsibility for such damage 30 www auroramultimedia com Aurora Multimedia Corp 205 Commercial Court Morganville NJ 07751 Phone 732 591 5800 Fax 732 591 6801
16. ctor at each end 1 No Video Signal d If used in electrical noisy environment shielded CAT cable may be required e If run is longer than 330ft or unit is in long range mode the signal will be limited to 24bit color depth Verify deep color is not turned on source equipment Check 24v power supply is plugged in Check to see if Wall supply is plugged into wall outlet Make certain wall outlet has power Verify the POE switch total power is adequate Some POE switch power ratings cannot supply the full 15 4 watts per port Make certain to multiply the amount of ports by 15 4watts and compare to the switches total spec b POE from Transmitter will only work on the non amplifier versions POE on receiver is not available for amplifier model a Verify using proper emitter or receiver to specifications outlined Use Aurora branded accessories for best results a This is normal HDBaseT receivers do run very warm when signal is applied You will note the transmitter runs much cooler a Exceeding recommend distance relative to cable specification b Use shielded cable Sometimes external devices like radio transmitters 2 LED is not lit vosy 3 LAN POE not working o 4 IR not working 5 DXE CAT RX3 is very warm 6 Intermittent Noise in image can interfere with HDBT signals Even though the DXE CAT series will work with non shielded cabling we recommend its usage for best perfor
17. e master Remote IP Target RPC Serial Port Number Enter the serial port number of the Aurora control device 17 User Guide Port Settings Pass Through Multimedia DXE LXC Activate IR repeater mode F Pass Through mode allows the serial ports on both the DXE CAT TX and DXE CAT RX to become a virtual cable link The serial receive of one unit will be sent to the serial transmit of the other unit IP commands will still force serial strings out the local or remote ports when necessary 18 User Guide SERIAL COMMANDS RS 232 Commands Command Query Response lt cr gt 0x0D Hex 13 Decimal Command String Format Information x Port Number 1 or 2 1 is far side over HDBT 2 is local port b Baud Rate 1200 115200 d 7 or 8 Data bits p O E N Parity s 1 or 2 Stop bits Example 30BR1 9600 8N1 lt cr gt for 96008N1 on remote Baud Rate 30BRx b dps lt cr gt port x Relay Number 1 or 2 Relay On Off Toggle 30RLYx y lt cr gt y 0 1 T On 1 Off 0 Toggle T Amplifier Mixer Volume for x 0 120 78dB to OdB HDBaseT HDMI 30AMH x lt cr gt x or Vol increment or decrement in steps of 2 Amplifier Mixer Volume x 0 120 78dB to 0dB for Line Input 30AML x lt cr gt x or Vol increment or decrement in steps of 2 Line Output Mixer Volume for x 0 120 78dB to OdB HDBaseT HDMI 30LMH x lt cr gt x or Vo
18. itters such as the DXW 2 Series HDBaseT wall plates DXE CAT TX1 DXE CAT TX2 DXM Matrixes etc The built in relays are perfect for screen control and the audio amplifier versions will fill the room with sound when used with the Aurora SKR 22T 360 sound field ceiling tile speaker A low cost highly integrated solution for rolling carts podiums and credenzas is possible with the DXE CAT family Being able to go the distance is important too and HDBaseT technology helps achieve that With a single CAT cable the DXE CAT can go up to 328ft 1080p 60Hz 48bit color depth 500ft 1080p 60Hz 24bit CAT 6 or GOOft 1080p 60Hz 24bit CAT 6A Shielded depending on model and cable In addition the RS 232 IR amp LAN can be sent over the same cable bi directionally Another industry first is the ability to serve up web control pages via LAN to any browser enabled device ex iPad iPhone PC Android to take control of the RS 232 IR and LAN This is done with the Aurora LXC control system engine inside so not only is the DXE CAT an HDMI extender receiver unit but a fully functional autonomous control system that can operate stand alone or as a port expansion for any control system on the market Aurora once again is setting the bar for form and functionality at a competitive price User Guide Features Receives HDMI up to 1080p 60Hz 48bit 330ft over one CAT 5e 6 7 cable Receives HDMI up to 1080p 60Hz 24bit 500ft over one CAT 6 cable
19. ized e LAN1 2 10 100 LAN connections LAN1 can use POE from a POE switch to power both the RX and TX units These ports are a switch Only 1 LAN port should be connected to another switch Note on the Amplifier versions POE will not work External 60W 24V DC supply must be used e Relays 2 Normally Open Relays capable of handling up to 24V DC at 2A e Amplifier Left Lt L and Right R R 4 8 Ohm Outputs capable of 35 Watts per channel Amplifier version must use the 90 Watt desktop 24V DC power Supply Note Some POE switch do not supply the full 15 4watts per port Verify the total power rating of the switch It should be at least 15 4W x number of ports User Guide IR EXTENDERS IR Blaster IR Receiver IR Connections The DXE CAT Series has the ability to auto detect on the IR port if a receiver or a blaster emitter is connected IR Blaster Emitter Plug in an IR blaster to emit all IR command signals received from the IR receiver to control the associated devices with built in IR sensor IR Receiver Plug in an IR receiver to receive all IR command signals from the IR remote controls of the associated devices Note if you are not using an approved Aurora branded receiver make certain you do not exceed the 5v signal level limitation as some devices use 12v Failure to do so will result in damage When the DXE CAT TX2L is set for manual the only way to send IR commands is using IR files loaded on the ftp of the u
20. l increment or decrement in steps of 2 Line Output Mixer x 0 120 78dB to OdB Volume for Line Input 30LML x lt cr gt x or Vol increment or decrement in steps of 2 Line Output Boost Volume 30LVL x lt cr gt x 0 9 1dB steps OdB to 9dB Amplifier Boost Volume IBOAVL x lt cr gt x 0 9 1dB steps OdB to 9dB Mute All 30MUT x lt cr gt x 0 1 T 0 Muted 1 Unmuted T Toggle X 1 or 2 1 HDBT 2 Local Serial Port This command determines which port the LXC will be LAN Serial Port Select 30PTL x lt cr gt linked to when communicating LAN Response 30BR x b dps lt cr gt x Port Number 1 or 2 1 is far side over HDBT 2 is Query Baud Rate 30BRx lt cr gt local port Response 30FM x lt cr gt Query Firmware x any value comprised of 2 digits with a decimal Revision 30FM lt cr gt separating the two Example FM 1 1 lt cr gt 19 User Guide Response 30RLYx y lt cr gt x Port Number 1 or 2 Query Relay On Off 30RLYx lt cr gt y Oor 1 On 1 Off 0 Query HDMI Amplifier Response 30AMHx lt cr gt Mixer Volume 30AMH lt cr gt x 0 120 78dB to OdB Query Line In Amplifier Response 30AMLx lt cr gt Mixer Volume 30AML lt cr gt x 0 120 78dB to OdB Query HDMI Line Out Response 30LMHx lt cr gt Mixer Volume 30LMH lt cr gt x 0 120 78dB to OdB Query Line In Line Out Response 30LMLx lt cr gt Mixer Volume 30LML lt cr gt x 0
21. link steady if unit is working properly Front Pin hole buttons Reset Use paper clip or similar object to reset unit by pushing into hole Setup For DXE CAT RX3C amp DXE CAT RX3C A models only User Guide Rear Panel DXE CAT RX3 SERIES DXE CAT RX3 RELAYS AMPLIFIER oase LAN2 RI R2 HDMI MEE Gr T HDBaseT OUTPUT L L GND R R LAN 1 Rear Connections e 24V DC Power connector for 15 24 90watt 24VDC power supply Note only 1 supply is required to power both units Either side can send power to the other unit Note if LAN POE is utilized for the non amplifier models the 24VDC supply is not required e IR Plug IR receiver or emitter into this port It will auto detect the mode of operation required e RS 232 Connect RS 232 device up to 115k baud e HDBaseT Connect CAT 5e 6 7 cable Shield cable is not necessary unless the environment has a lot of electrically noise e HDMI Output Plug HDMI cable from destination device like an LCD display Note the HDMI cable should be rated for the bandwidth you are using e Line In Out Line level input left and right on the top and line level output from the HDMI on the bottom The input and output are balanced capable The line input can be mixed with the line output for applications like wireless microphone receiver or paging Using RS 232 commands locally or remotely the volume and mixing can be controlled For the L models IP commands can be util
22. lt IP address and password Firmware Update Mode This but forces the unit into an update mode It is recommended to use the firmware update tool LXupdate which is available on the Aurora website Restart DXE LXC Remotely reboots the unit Network Settings DXE LXC User Guide za URORed Viultinedia DXE LXC Network Setup Current Network Settings IP Address 192 168 1 10 Subnet Mask 255 255 0 0 Gateway 192 168 1 1 Hostname DXELXC MAC Address 00 11 02 b0 00 00 Network Configuration pjicp Static IP Address Subnet Mask Gateway Hostname Extra RPC Server TCP Port Current Network Settings Shows the current IP Address Subnet Mask Gateway Hostname and Mac Address Network Configuration This section allows the turning on off of the DHCP and allowing the entry of static IP settings if DHCP is not utilized If you use DHCP it is always recommended to use a switch that can map the MAC address to a defined IP address otherwise the IP address may change inadvertently at a later time making it difficult to target the device Hostname can only be utilized on a NETBIOS system If TCP commands are used there is a setting for the TCP server port number Make certain once done making changes to press apply changes 10 User Guide Port Settings w JUROR Multimedia DXE LXC DXE LXC Port Setup Master Remote IP 4 0 0 0 Local Serial Port 1 Baud Rate 115200 Settings d Dat
23. mance a The IR on the RX side is limited to 38kHz so only remotes with 38kHz 7 IR port on RX side does not work carrier will work Keep in mind some remotes between 36kHz 40kHz with some devices may work The TX side which is local to the processor will work with carrier frequencies from 30kHz to 100kHz 8 Need to update firmware a Use LXupdate found on the Aurora website a Make certain only 1 LAN port is connected to same switcher The DXE 9 Cannot ping IP address CAT LAN ports are a switch not a router b Make certain unit is an C version and has the IP option 10 RS 232 is not communicating a Verify baud rate setup is correct on each port 1 All transmission distances are measured using West Penn cable as per Appendix 4 The transmission distance is defined as the distance between the video source and the display 2 To reduce the interference among the unshielded twisted pairs of wires in UTP cable you can use shielded STP cables to improve EMI problems which is worsen in long transmission Warning Do not plug RJ 45 HDBaseT output to non HDBaseT compliant devices or damage may occur to either product 25 User Guide APPENDIX 2 Firmware Update Main processor update Latest firmware and update tool for the main processor can be found at the Aurora website customer portal Instructions are included in the zip file Web server firmware update Latest firmware and update tool for the web server can be fou
24. nd at the Aurora website customer portal Instructions are below LXupdate exe is a Windows Command Line tool to field upgrade LX class products usage LXupdate filename targetIP filename is the name of the file containing the image to upload targetIP is IP address of target in ddd ddd ddd ddd format The tool uses UDP port 9 or port 49444 to force targeted devices into programming mode When these are not available the force button on the main page of the LX device interface must be used UDP Ports 67 68 and 69 are also required 26 User Guide APPENDIX 3 Technical Specifications Model Name DXE CAT RX3 Series DXE CAT RX3 DXE CAT RX3 A DXE CAT RX3C DXE CAT RX3C A 600 1080p 60Hz Max 115kbps Amplifier No 2x35 Watt 4 8 Ohm No 2x3 5Wattt 4 8 Ohm Balanced 24VDC 2A 24VDC 2A 24VDC 2A 24VDC 2A 30Hz 100kHz 30Hz 100kHz 2 10 100 Amplifier Requires Amplifier Requires LAN Ol ron External Power se External Power IP Control System No Of w es Yes Power Status HDMI Power Status HDMI Power Status HDMI o Front LED Status HDBaseT RS 232 HDBaseT RS 232 HDBaseT RS 232 TX RX IR In Out TX RX IR In Out TX RX IR In Out bears a Front Selections Reset Setup Reset Setup 328ft 100m 1080p 60Hz 24 amp 36bit CAT 5e 6 6a 7 328ft 100m 1080p 60Hz 48bit CAT 6a 7 230ft 70m 1080p 60Hz 48bit CAT 5e 6 6a 7 Distance 500ft 152m 1080p 60Hz 24bit Long Reach Mode CAT 6 600ft 183m 1080p 60Hz 24bit
25. nit in the IR directory Aurora IR files wir are available for download on the Aurora website In addition IR files learned from NX or QX control devices can be utilized IR Jack Pinout IR Blaster IR Receiver IR signal Grounding Power Grounding Emitters must be mono plug or have ring and sleeve tied to ground Receivers must be stereo plug Ring is 5v power If using another brand receiver note carrier frequency must be stripped and IR signal cannot exceed 5v or damage to port may occur User Guide IP SETUP Introduction The IP function allows the DXE CAT RX3C and DXE CAT RX3C A to be controlled via LAN In addition the units can be set up with built in setup pages and even serve up web pages to remote devices on the network for control Default IP The default IP out of the box is 192 168 1 10 static Make certain to change the IP on the unit at a time or you will get collisions on the network Each device must have a unique IP address DHCP can be used but it is recommended to issue IP address based on the MAC address This assures the DHCP does not reassign the IP address at a later time causing issues Keep in mind the processor is on the TX unit so only the TX needs to be connected when you are doing the initial setup although having the RX will not affect the process and may be necessary only if the LAN is connected at the RX side To access the settings via web browser use the units IP address setup ex
26. or Aurora DXE CAT RX3 Series HDMI HDBaseT CAT Extender with Audio De embedding Relays 2x35W Amplifier amp IP Control DE N DXE CAT RX3 IROut TX HDBT Power Aurora DXE CAT RX3 RELAYS AMPLIFIER e r Vi fe Ell ee HDMI a Ma HDBaseT OUTPUT L L GND R R RI R2 RS 232 Manual Number 140807 Firmware v1 07 or higher User Guide SAFETY INSTRUCTIONS Please review the following safety precautions If this is the first time using this model then read this manual before installing or using the product If the product is not functioning properly please contact your local dealer or Aurora for further instructions A The lightning symbol in the triangle is used to alert you to the presence of dangerous voltage inside the product that may be sufficient to constitute a risk of electric shock to anyone opening the case It is also used to indicate improper installation or handling of the product that could damage the electrical system in the product or in other equipment attached to the product N The exclamation point in the triangle is used to alert you to important operating and maintenance instructions Failure to follow these instructions could result in injury to you or damage to the product AX Be careful with electricity Power outlet To prevent electric shock be sure the electrical plug used on the product power cord matches the electrical outlet used to supply power to the Aurora product Use only the powe
27. r adapter and power connection cables designed for this unit Power cord Be sure the power cord is routed so that it will not be stepped on or pinched by heavy items Lightning For protection from lightning or when the product is left unattended for a long period disconnect it from the power source A Also follow these precautions Ventilation Do not block the ventilation slots if applicable on the product or place any heavy object on top of it Blocking the air flow could cause damage Arrange components so that air can flow freely Ensure that there is adequate ventilation if the product is placed in a stand or cabinet Put the product in a properly ventilated area away from direct sunlight or any source of heat Overheating Avoid stacking the Aurora product on top of a hot component such as a power amplifier Risk of Fire Do not place unit on top of any easily combustible material such as carpet or fabric Proper Connections Be sure all cables and equipment are connected to the unit as described in this manual Object Entry To avoid electric shock never stick anything in the slots on the case or remove the cover Water Exposure To reduce the risk of fire or electric shock do not expose to rain or moisture e Cleaning Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning e ESD Handle this unit with proper ESD care Failure to do so can result in failure
28. werOn lt 0D gt out the RX serial port method Serial_ Send amp param1 2 amp param2 PowerOn 0D amp param3 100 Send the Play command to a DVD player on the DXE CAT RX3 SERIES TX side method IR_SendCommand amp param1 1 amp param2 DVD amp param3 Play Retrieve a list of all IR file names method GetIRFileNames Response Tokens status 0 for Failure 1 for Success faultCode If status is 0 failure faultCode will be an integer representing a specific error This token is NOT returned if status is 1 Success response i Returned value i where is an integer If status is 0 fail the value for response will be a string describing the failure and the value for b will be a debug string giving more information about the failure Example using the call for the Net_GetSubnetMask method method Net_GetSubnetMask Sample response status 1 amp response1 255 255 255 0 22 User Guide WEB SERVER The DXE CAT RX3C RX3C A has a built in web server that can hold up to 8MB of web pages including firmware Using FTP webpage s can be uploaded to the wwwpub directory Web pages utilizing HTML Flash AJAX etc can be served up using the units IP address or host name if NetBIOS is used Aurora has a free tool called YIPI available for download on the Aurora website to create webpages quick and easily YIPI also has the ability to FTP to the unit as well Please note that only the YIPI HTML export will work with the
29. xWaitMS MaxWaitMS The number of milliseconds allowed to complete the sending of the serial data before timing out GetWebFileNames Returns the names of the web files GetIRFileNames Returns the names of the IR files Serial_Read Port Reads the serial buffer for a specific serial port 12 Serial_ClearReadBuffer Port Clears the serial buffer for a specific port 1 Serial_ReadBufferCount Port Reads the buffer count for a specific port 1 Serial_GetPortCount Returns the total number of available serial ports 2 1 IR GetPortCount Returns the total number of available IR ports 2 1 Sends an IR command from the specified port 1 IR_SendCommand Port Group Command Group The IR file name Command The IR command name IR_ListAllGroups Returns all loaded IR groups files IR_ListAllCommandsInGroup Group Returns all IR commands in a specific group Returns the ID of the DXE CAT RX3 SERIES controller used for communication with other Aurora controllers SetDefaultConfig Resets the DXE CAT RX3 SERIES settings to factory default 1 Serial port 1 IR port 1 is located on the DXE CAT RX3 SERIES RX unit serial port 2 IR port 2 is located on the TX GetMachineType unit 2 Hexadecimal data is represented with a percent sign preceding the 2 byte hex code e g 0D for carriage return 21 User Guide TCP RPC Command Usage Sample Usage Send the serial command Po
Download Pdf Manuals
Related Search