641G-001A PRINTER KIT INSTRUCTIONS
Contents
1. 641G 001A PRINTER KIT INSTRUCTIONS N SHIVVERS INCORPORATED 614 WEST ENGLISH CORYDON IOWA 50060 515 872 1005 P 11351 5 05 98 SAFETY The installer of this equipment must assume the responsibility for his own safety and that of those working around him He must also make sure that the equipment is installed as shown in this manual If any items covered in this manual are not completely understood or there is a concern with the safety of this product contact Shivvers at the address shown on the front page TAKE NOTE ANYTIME THIS SYMBOL APPEARS YOUR SAFETY AND THAT OF PERSONS AROUND YOU IS AT STAKE ALL ELECTRICAL WIRING SHALL BE INSTALLED IN COMPLIANCE WITH THE LATEST EDITION OF THE ANSI NFPA STANDARD 70 NATIONAL ELECTRICAL CODE AS A MINIMUM REQUIREMENT AND IN COMPLIANCE WITH LOCAL WIRING CODES AS APPLICABLE WIRING MUST BE DONE BY A COMPETENT ELECTRICIAN A LICENSED ELECTRICIAN IS RECOMMENDED AND MUST BE USED WHEN REQUIRED BY LOCAL OR STATE STATUTES PRINTER KIT CONTENTS POWER TRANSFORMER enone PAPER HOLDER Ree i SPINDLE PRINTER ee CABLE E J STRAIN ET RELIEF DESCRIPTION PART PRINTER Comes in E 6056 POWER TRANSFORMER PRINTER CABLE E 6272 STRAIN RELIEF E 6111 PAPER HOLDER ASSY neues BAPER HOLDER 641 035P PAPER SPINDLE 597 391P CAP PLUG H 1900 SNAP RING F 1080 The printer kit also contains mounting screws and the wiring harness for the power outlet in the printer mountin2. cable to connect to the 10 pole plug on the plenum control and pull the excess down below the printer box The illustration on the next page shows how to route the printer cable 10 POLE l00000000000000 000600600 77 E TE Sf 6 RUN CABLE 7 TO BEHIND MOUNTING BRACKET Ds CABLE CLIP The printer cable connects to the plenum control on the 10 pole plug located to the right in the plenum control The Red wire in the printer cable connects to terminal 5 of the 10 pole plug The Black wire connects to terminal 6 of the 10 pole plug The shield connects to terminal 7 of the 10 pole plug See wiring decal inside main cover for further reference Double check all wiring then replace wiring access cover on plenum control close and latch main cover Turn power back on to Command Center Open the access door and turn on the control power the printer should print Ready if it doesn t disconnect and lock off power and check wiring SETTING UP THE PRINTER When the printer is first installed the time date format will need to be set To do this you must first access the setup menu With control power off press and hold down the left side of the rocker switch and turn control power on The printer will advance the paper After the paper advance has stopped count 3 5 seconds and release the switch The printer should print the following SETUP MENU CONFIGURE N
3. EXT OK If you wait less than three or more than five seconds Ready is printed and you will have to try again to access the setup menu After you access the setup menu if you press NEXT left side of rocker switch you will see the following printed SETUP MENU CONFIGURE NEXT OK CUSTOM NEXT OK With CUSTOM as last item printed press OK right side the printer will print the following SETUP MENU CONFIGURE NEXT OK CUSTOM NEXT OK kkk CUSTOM MENU PRINT CUSTOM SETUP NEXT OK With PRINT CUSTOM SETUP as last item printed press NEXT left side to display the time date format Keep pressing NEXT until the time format printed looks like MM DD YY hh mm then press OK right side Now printer should show SETUP MENU CONFIGURE NEXT OK CUSTOM NEXT OK k kKKK CUSTOM MENU PRINT CUSTOM SETUP NEXT OK MM DD YY hh mm M DOW NEXT OK MM DD YY hh mm NEXT OK AUTO T amp D YES NEXT OK With AUTO T amp D YES as last item printed press NEXT left side to change selection to NO The printout should now look like SETUP MENU CONFIGURE NEXT OK CUSTOM NEXT OK kkkkKKK CUSTOM MENU PRINT CUSTOM SETUP NEXT OK MM DD YY hh mm M DOW NEXT OK MM DD YY hh mm NEXT OK AUTO T amp D YES NEXT OK AUTO T amp D NO NEXT OK With AUTO T amp D NO as last item printed keep pressing OK right side until Ready is printed The print
4. er should now be configured to operate with the Command Center properly For more information see the Model 1220 Printer Series User s Manual OPERATING THE PRINTER When control power is applied to the printer Moisture Control and Plenum Control the red light on the printer should be on and the printer should print Ready The Moisture control will flash the program number Press the adjust switch on the Moisture Control and the printer should start printing out SHIVVERS program version and the current drying parameters If the printer prints out READY but not the other information the printer is not properly connected to the Plenum Control The printer can be turned off by pressing the left side of the rocker switch on the printer This puts the printer in standby The LED on the printer will go off while the printer is in standby Below is a sample printout of the Moisture Control drying parameters and data SHIVVERS PLENUM CONTROL P1 1 DRYING PARAMETERS 27 98 STATUS OF MACHINE TIME OF SAMPLE O78F 15 0 ON 15 30 14 9 078F 14 9 ON 180 181 15 35 15 0 078F 14 9 ON O78F 18 6 ACTUAL TEMPERATURE MOISTURE CONTENT OF SAMPLE TARGET LAST 2 9 TEMPERATURE GRAIN SAMPLE SAMPLES TEMPERATURE The drying parameters will also be prin
5. g box INSTALLATION DISCONNECT AND LOCK OUT POWER TO THE A DY NA Ce J 2a ENTIRE DRYING SYSTEM BEFORE OPENING THE MAIN COVER ON THE CONTROL BOX Before opening the main cover on the Command Center disconnect and lockout all power Test several points with a known good tester to verify power has been disconnected Begin by locating the printer mounting box and the wiring access cover on the Plenum Control Remove the wiring access cover by removing the 2 screws fastening it to the plenum control PLENUM MOUNTING O e CONTROL LOCATION SHIVVERS FOR PAPER WIRING ACCESS HOLDER s TUARA 1 a e COVER PRINTER BOX Install the paper holder on the wiring access cover in the location shown above using the 2 8 32 x 3 8 screws and nyloc nuts provided with the installation kit For right hand operation mount the paper holder with the screw and snap ring on the right side The paper spindle can be temporarily removed for this procedure Do not reinstall wiring access cover until printer wiring is completed Inside the printer box is an appliance outlet Take the wiring harness supplied with the kit and install the black wire on the terminal for the narrow slot on the appliance outlet The white wire from the wiring harness connects to the terminal for the longer slot White or neutral wire Black or 115VAC wire The other end of the wiring harness connects to the switch relay panel to connector J1 See
6. is in a weather resistant enclosure it is a good idea to remove the printer and the power transformer and store them inside during the off season To do this simply remove the printer cable connector by loosening the 2 screws that hold it to the printer and unplug the AC adapter from the AC outlet in the printer mounting plate then remove printer and AC adapter If the printer hasn t been used in a while the printout may be faint This could be due to the exposed ink ribbon drying out To advance the printer ribbon hold down the paper feed switch for a few seconds to expose new ribbon If this does not fix the problem a new ribbon cartridge may need to be installed Replacement paper and ribbons can be ordered from Shivvers The part for the paper is C 6180 The paper is standard paper 2 1 4 wide The part for the ribbon cartridge is C 6179 The Epson number for the ribbon is ERC 09 or HX 20 See the printer user s manual for details on replacing the paper and the ribbon cartridge
7. owing is printed SET CLOCK NEXT OK k SET DATE SET YEAR ff7 NEXT OK SET YEAR 9Off NEXT OK The cursor now appears over the 2nd position Press NEXT left side to increment this number if needed or OK when it is right Continue this sequence of accepting or changing the year month day and DOW Day Of Week SET CLOCK NEXT OK x SET DATE SET YEAR 7 NEXT OK SET YEAR Q NEXT OK SET MON 5 NEXT OK SET MON Of NEXT OK SET DAY B3 NEXT OK SET DAY 2K NEXT OK SET DOW 5 NEXT OK When you have completed the SET DATE menu the following is printed k SET TIME SET HOUR fl6 NEXT OK Choose NEXT left side to increment this number or OK right side to accept it Repeat this same procedure for hours and minutes as shown below xx SET TIME SET HOUR M6 NEXT OK SET HOUR 1f NEXT OK SET MIN K6 NEXT OK SET MIN 3 NEXT OK START CLOCK ec gies Ha edie Gea OK Ready When everything is as you want it and you press OK START CLOCK is printed Press OK right side to start the clock The printer then prints Ready showing you that it is out of the setup menu and ready to print This procedure is also explained in the printer user s manual supplied by the printer manufacturer 10 STORAGE AND MAINTENANCE Although the printer
8. ted out after 72 and 144 on samples or when the Set Transfer Moisture is changed SETTING THE CLOCK To set the clock you must first access the setup menu To do this unplug the printer at the outlet or at the back of the printer or turn control power off Press and hold the left side of the rocker switch and turn power on The printer will advance the paper After the paper advance has stopped count 3 5 seconds and release the switch The printer should print the following SETUP MENU CONFIGURE NEXT OK If you wait less than three or more than five seconds Ready is printed and you will have to try again to access the setup menu After you access the setup menu if you press NEXT left side of rocker switch repeatedly you will see the following list printed If you keep pressing NEXT left side the list will repeat itself SETUP MENU CONFIGURE NEXT OK CUSTOM NEXT OK SET CLOCK NEXT OK RESET SEQ NEXT OK CONFIGURE NEXT OK To set the clock press NEXT until set clock is the last item printed If you press OK right side the printer will print the following SET CLOCK NEXT OK SET DATE SET YEAR ff7 NEXT OK The printout shows the year currently in memory The 9 is reversed white on black to show the position of the cursor This will be the number incremented if NEXT left side is pressed If the number is correct press OK right side and the foll
9. wiring decal on inside of main cover for reference Terminal J1 is located on the bottom right hand corner of the switch relay panel The white wire connects to terminal J1 7 This is the neutral The black wire connects to terminal J1 8 This is the 115VAC source Take the printer cable assembly and connect it to the back side of the printer The printer cable connector is narrower at the bottom and will only go on one way Using a small screwdriver tighten the 2 screws on the cable connector to secure it to the printer Place the printer into the printer box on the sloped mounting plate Place the wire end of the printer cable through the strain relief and slide it up the cable until its about 10 inches away from the connector then place the printer cable through the hole located in the right hand corner of the printer box Close the strain relief and press it into the hole in the printer box The strain relief will have to be held closed while it is being inserted i Leave about 10 of cable above Strain Relief TOP OF STRAIN SLOPED RELIEF MOUNTING poe PRATET ESRA 4 APPLIANCE Tf OUTLET Plug the power transformer adapter into the printer The connector is located on the back of the printer then plug the transformer into the appliance outlet Route the printer cable from the bottom of the printer box up through the cable clip located on right side of the control box up the right side and behind the plenum control Leave enough
Download Pdf Manuals
Related Search