Home

Instructions for Use and Installation HNS – M / HLS STEAM

image

Contents

1. Instructions for Use and Installation HNS M HLS 4 Steamer connections HNS M Citric acid filling HNS M Steam pipe 1 2 Plug for the Water connection 3 4 omens Main switch magnetic valve HNS M Water flushing 1 2 Manual or electric HLS Water connection Zo Indicator light connection Pneumatic Kit Optional Din connector for the control panel Roma and Roma lI Optional and the Split Box Ontiona Main switch Power supply Connection for pneumatic remote control Pneumatic Kit Optional Water and steam connection Connect the flexible water connection tube in the packaging to the water connection in the installation panel of the unit and to the cold water piping of the building The water pressure must be between 0 2 and 10 bars The water supply pipe must have a manual stop valve for stopping water supply to the unit if the unit is not used for a prolonged time Installation must follow the local regulations It is recommended to use at least 18x16mm steamer size 3 4 kW 9 5 kW and 22x20mm steamer size 12 0 kW 14 kW copper pipe or a silicone tube of similar size when connecting the steam pipe The steam pipe diameter must be the same for the whole length The steam pipe must be tilted upwards or downwards from the steam generator to the steam room there MUST NOT be any water seals or water pockets The condensation water forming in the steam pipe must be allowed to drain f
2. programme has finished Testing the water quality and decalcification for HELO HNS M and HLS steamers The test packet that comes with the steamer includes test slips which can be used for testing the water hardness number as follows dip the test slip in water for about 1 second take it out and shake off the excess water After a minute compare the colour code appearing on the test slip with the code key in the packet Test result lt 3 dH Very soft water Decalcification after every 500 hours of use gt 4 dH Soft water Decalcification after every 100 hours of use gt 7 dH Medium hard water Decalcification after every 50 hours of use Installing the decalcification device recommended gt 14 dH Hard water Decalcification after every 30 hours of use Install decalcification device and retest the water hardness gt 21 dH Very hard water Install decalcification device and retest the water hardness The product s warranty will be void if the steam generator has been incorrectly installed or it has been used in a manner other than described in the user manual The warranty also expressly excludes operational faults if they are caused by hard water i e water with high levels of chalk or otherwise impure water The steam generator must be maintained as described in the user manual Instructions for Use and Installation HNS M HLS 8 Decalcification instructions Decalcification procedure for the HNS M
3. it should be delivered to a collecting place for the recycling of electrical and electronic devices The symbol on the product the instruction manual or the package refers to this The materials can be recycled according to the markings on them By reusing utilising the materials or by otherwise reusing old equipment you make an important contribution for the protection of our environment Please note that the product is returned to the recycling centre without any sauna rocks and soapstone cover Please contact the municipal administration with enquiries concerning the recycling place Anvisningar f r milj skydd Denna produkt f r inte kastas med vanliga hush llssopor n r den inte l ngre anv nds Ist llet ska den levereras till en tervinningsplats f r elektriska och elektroniska apparater Symbolen p produkten handboken eller f rpackningen refererar till detta De olika materialen kan tervinnas enligt m rkningen p dem Genom att teranv nda nyttja materialen eller p annat s tt teranv nda utsliten utrustning bidrar du till att skydda v r milj Produkten returneras till tervinningscentralen utan bastusten och eventuell t ljstensmantel V nligen kontakta de kommunala myndigheterna for att ta reda pa var du hittar n rmaste atervinningsplats Hinweise zum Umweltschutz Dieses Produkt darf am Ende seiner Lebens Dauer nicht tiber den normalen Haushaltsabfall Entsorgt werden s
4. 1 x K2 Power requirement kw Air conditioning No A C Acrylic wall Light wall board tile Heavy wall stone concrete tile Very heavy wall stone concrete K1 0 75 K1 0 52 K2 1 00 K2 1 25 K2 1 50 K2 2 00 In heavy built steam rooms it is recommended to use e g electric heating cable for warming the seats walls and floors Heating elements Teho Power Leistung Vastus Element Heizst be 230V 240V 1000W SEPD 131 1150W SEPD 97 1567W SEPD 98 2000W SEPD 99 2567W SEPD 100 5250W SEPD 116 4250W SEPD 119 5250W SEPD 116 1000W SEPD 130 1150W SEPD 111 1567W SEPD 112 2000W SEPD 113 2567W SEPD 114 3500W SEPD 115 3500W SEPD 115 3500W SEPD 115 1000W SEPD 131 1150W SEPD 97 1567W SEPD 98 2000W SEPD 99 2567W SEPD 100 5250W SEPD 116 4250W SEPD 119 5250W SEPD 116 Instructions for Use and Installation HNS M HLS Connection diagrams Only 400V 3N 3 4 7 7 kW 230 V 1N 2 ae ee 2 3 4 14 kW 400 V 3N 1 4 5 6 Sun L2 D L2 L3 amp N L1 L2 L3 1 Termostaatti liit nt Ext thermostate Thermostatanschl 2 Merkkivalo 12V DC led Signal light Signalleuchte 3 Pneum kaukoohjaus Pneum remote control Pneum Fernsteuerung HLS 3 4 7 7 kW 230V 240V 1N 2 230V 3 400V 415V 3N HLS 9 5 14 0kW 230V 3 400V 415V 3N Heating Contactor elements 3 4 7 7 KW 230 V 1N 2 1 t f S L1 N L
5. 2 3 4 14 kW 230 V 3 1 2 t 14 L1 L2 L3 3 4 14 kW 400 V 3N Bo Sie t ftt amp n L1 L2 L3 Upper limit __ S s2 Lower limit Sir S1 Serial traffic Surface sensor 5 to MIDI controller Push button Thermostat 2 T1T2 A K S1 S2 TX RX 0 Alarm 12 VDC max 200 mA Light control opto max 24 V DC 50 mA eo 6 efe a e eea 6 ofa LC1 LC2 B Water valve Water valve flush filling 230V AC 230V AC 354 SHS 40B HNS M 3 4 7 7 kW 230V 240V 1N 2 230V 3 400V 415V 3N HNS M 9 5 14 0kW 230V 3 400V 415V 3N Instructions for Use and Installation HNS M HLS 7 Steam generator maintenance procedures Flushing and rinsing HNS M steamer has an option for an automatic flush and rinse cycle Optional 15 minutes after the bathing programme has finished or the programme has been manually aborted the electronic flush valve will open After the flush the steamer will fill its tank again with cold water and flush it again rinse By emptying the steamer s tank straight after use the product will gain a long life cycle even in areas where water quality leaves room for improvement Flushing the tank is not a substitute for a regular decalcification procedure After the flush and rinse cycle the unit will shut down to stand by mode until the next bathing programme is initiated HLS has an option for a flush valve Auto clean kit which flushes the steamer water tank 4 hours after the
6. 310130 HNS M Automatic flushing Auto clean kit 3819497 HLS Descale Kit HLS Instructions for Use and Installation HNS M HLS 3 Use and installation HNS M and HLS steam generators are only intended for use in heating spa facilities Using steam generators in other areas than steam rooms can damage the building s structure The manufacturer is not responsible for damages caused if the unit has been used incorrectly or in a manner for which the unit was not designed for Water and steam pipe connections must be made prior to connecting the unit into the mains Due care and attention must be taken when making the connections Proper sealing must be ensured for all extensions A good extension must have at least taped over twist connections but it is recommended that connections are soldered The steam generator must be placed away from water and moisture dry room The room must be airy as the unit also produces heat The maximum recommended ambient temperature is 25 C The minimum recommended free space to the sides and above the steamer is 30cm Adequate space for maintenance should also be planned for in the placement of the unit There should be a drain nearby for draining the tank The steam generator can be installed freestanding on the floor or on the wall using wall fittings When using wall fittings ensure you use appropriate fittings and screws for the type of construction material of your walls The steam generator
7. LS 10 Control panel functions The steamer is started by pressing the ON OFF button in the control centre After that the temperature display starts to flash The temperature may be set with the and buttons in one decree steps between 25 C 50 C If the temperature on the display is correct you can move to time display by pressing the OK button When the display flashes you can adjust the time with the and buttons in one minute steps up to 90 minutes after which the display changes to the hour display max 4 hours When there is 90 minutes left the display changes to minute display Before that only full hours remaining are shown The last set temperature and time are stored in memory Lighting controls Lights can also be controlled with the control centre button which lights the led indicator lights by the push button The connectors LC1 and LC2 on the circuit board are for lighting control External voltage is brought to the circuit board 24 V DC max 50 mA connected to connector LC1 When the light button is pressed the opto switch on the circuit board transfers the voltage to connector LC2 which controls the actual lighting control unit Light adapter 0043214 Push button Led indicator light ON OFF button Button function When the steamer is started with the push button it runs for 30 minutes The led indicator light above the push button lights Steamer time cannot be adjusted it stops automatical
8. ed when E1 or E2 error message appears on the display or when the led on the push button flashes rapidly The alarm is confirmed with the ON OFF push button Instructions for Use and Installation HNS M HLS 11 Installing control panel push button and thermostat The control panel is filled with sealant therefore is moisture resistant The control panel may be installed directly on a wall Pipe hole in the steam room should be sealed so that moisture does not travel along the pipe This way the cable is hidden behind the control panel Alternatively the cable can come out of the bottom of the control panel from a pre marked hole Control panel frame is pressed directly on it Detaching is done with tool that comes with the unit The frame has small holes on the edges 4 holes Push the locking pin lightly with the tool through the hole one at the time and pull the frame outwards at the same time The push button is filled with sealant therefore it may be installed in the steam room The push button may be installed through a wall acrylic walls or by making a suitable hole where the push button can be embedded and sealed with appropriate sealant Surface installation boxes may also be used if necessary they do not need to be tight because the actual push button is moisture resistant The thermostat is installed at 170cm height from the floor preferably on the wall opposite the door Retaining nut may be used if nece
9. helo GENUINE SAUNA amp STEAM Instructions for Use and Installation HNS M HLS STEAM GENERATOR CONTROL CENTRE HLS Roma 1 Roma2 Pneumatic push button HNS M Midi On Off push button For home and professional use HNS M HLS 314 SHS 89 B Instructions for Use and Installation HNS M HLS Specifications Operating voltage 230V 1N 2 3 4 kW 7 7 kW 230V 3 3 4 kW 14 kW 400V 3N 3 4 kW 14 kW Also available 240V 1N 2 415V 3N Output options 3 4 4 7 6 0 7 7 9 5 12 0 14 0 kW Parallel coupling HLS max 3 steamers 42 kW HNS M max 1 steamer 14 kW Enclosure class IP 20 Installation Floor wall Water tank material Aisi 304 stainless steel Steamer dimensions 520 x 380 x 160 mm Weight when empty about 11 kg Easy to use Floor or wall installation Digital control panel or On Off push button HNS M Analogue control panel HLS Control centre installation in steam room allowed HNS M Control centre installation outside the steam room HLS Easy maintenance Replaceable heating elements 3 pcs of which 1 is fitted with a heat fuse Fill cap for deliming agent citric acid on the lid of the steam generator HNS M Optional HSL Descale Kit Components easily replaceable circuit board heating elements surface sensor Accessories Scent pump Essence kit 0038130 Scent pump canister 20 0038132 Automatic flush and rinse cycle Auto clean valve 4
10. ly Steamer can be stopped by pressing the push button even before the time has run out in which case the light turns off Steamer can also be restarted if desired A separate limiter thermostat can be used with the steamer if push the button controls are used Thermostat 0043210 The thermostat prevents the temperature in the steam room from raising above 50 C See thermostat installation on the next page Alarms Midi RA 17 Control centre E1 Water tap is closed when the steamer is started or running or some other reason prevents water from running into the steamer Open the tap If the malfunction is in the steamer it may require service E2 Error message comes when serial traffic between the control centre and the circuit board is not working Troubleshooting requires service The steamer stop after the error message Fix the cause of the malfunction or call service Malfunction can be confirmed with the ON OFF button Push button led indicator light flashes rapidly in a steamer equipped with a push button if there is a malfunction in the steamer steamer has been started with the water tap closed or some other reason has prevented water from running into the steamer This notification appears when the steamer is running if water intake is cut off The error message can be confirmed with the push button Fix the malfunction or have it fixed The circuit board has an output for alarm 24 V DC max 50 mA The output is activat
11. ng the control centre or split box Optional The available control centres ROMA and ROMA II are connected to the DIN connector as shown in the figure Connection does not require a professional electrician users can do it themselves Split Box is required when other devices are connected to the steamer in addition to the control centre e g automatic flush valve Auto clean Kit or if the control centre controls more than one steamers max 3 steamers The steam generator may also be used without the control centre in which case the user must take care that the steam room temperature does not rise above 50 C A separate timer circuit OLEA 82 can be installed on the steam generator s circuit board OLEA 21 which stops the steam generator automatically after 25 minutes Optional Timer Circuit Indicator light Optional Pneumatic Kit Drill a hole in the wall and install the indicator light in the hole Seal the hole with silicone if necessary Plug connector is connected to the connector in the steamer The indicator light functions on 12V DC direct voltage therefore it is safe also in moist steam rooms Steam generator implementation 1 Open the manual water tap of the steamer 2 Press the main switch to position 1 3 Give the control input with the pneumatic push button or with the control centre Roma or Roma Il When there is enough water in the tank the electronics will switch the heating on and close the water intake
12. ondern muss an einem Sammelpunkt f r das Recycling von elektrischen und elektronischen Ger ten abgegeben werden Das Symbol auf dem produkt der Gebrauchsanleitung oder der Verpackung weist darauf hin Die Werkstoffe sind gem ihrer Kennzeichnung wiederverwertbar Mit der Wiederverwendung der stofflichen Verwertung oder anderen Formen der Verwertung von Altger ten leisten Sie einen wichtigen Beitrag zum Schutze unserer Umwelt Dieses Produkt soll ohne Steine und Specksteinmantel an dem Sammelpunkt f r Recycling zur ckgebracht werden Bitte erfragen Sie bei der Gemeindeverwaltung die zust ndige Entsorgungsstelle
13. r that by opening the flush valve Close the valve after the first flush ing and restart the steamer and allow the tank to fill up with water Stop and flush the stea mer again and repeat this about 3 to 5 times Steam generator in professional use In addition to decalcification treatment it is recommended to make a service plan for steam generators in daily use 6 hours or more Service is recommended to be done 6 times a year and it is to include visual inspection of the heating elements and the surface sensor inspection and cleaning lime accumulation of the inner surface of the tank and replacing components if necessary Tank cleaning is done through the heating element mounting holes Instructions for Use and Installation HNS M HLS Steamer use HNS M Control panel Midi RA17 Lighting controls Temperature display Time display Temperature adjustment 25 50 C Time adjustment 0 4 hours ei Du eh Temperature sensor GA C GAP Steamer on off Digital control centre Lighting control button opto switch max 24V DC 50 mA normal open OK button Bathing temperature selection button temperature display flashes Bathing time selection button time display flashes plus button for increasing time and temperature values minus button for decreasing time and temperature values ON OFF push button for starting and stopping the steam function Instructions for Use and Installation HNS M H
14. reely to the steam room or back to the steamer If a scent pump is connected to the steam generator the pipe must ALWAYS drain away from the steamer so that the chemicals cannot get into the tank Recommended maximum length for the steam pipe is 5m It is recommended to always use additional insulation for the steam pipe for both safety reasons and to prevent water condensation in the pipe WARNING Hot steam can cause burn injuries The magnetic valve for draining the steamer s tank is fitted into the draining pipe Alternatively you may use a manual draining valve The steamer s tank should be drained after each use This will extend the unit s life and reduces chalk build up Instructions for Use and Installation HNS M HLS Electrical connections The sauna heater must be connected to the mains by a qualified electrician and in compliance with current regulations Steam generator is connected with a semi permanent connection Use HO7RN F 60245 IEC 66 cables or a corresponding type Heater connection cable HO7RN F 60245 IEC 66 mm 400 415V 3N Heater connection cable HO7RN F 60245 Heater connection Fuse Room size cable HO7RN F 60245 IEC 66 mm 230 240V 1N 2 Heavy built walls such as concrete brick or stone require more power output to heat up Ventilation also adds to the required power output You can estimate the power requirement using the formula below Volume m3 x K
15. ssary on plexiglass walls On thicker walls you can make a hole and seal it with appropriate sealant to prevent moisture from entering the structures The thermostat is pushed into the cover which is then tightened with a clamping screw 55 mm Mounting hole 5mm Locking Locking Hole spacing 150 mm 180 mm Locking Locking Led indicator light ON OFF button 40 mm Retaining nut 46 mm Thermostat cover Thermostat Retaining nut Instructions for Use and Installation HNS M HLS 12 Steamer use HLS Steamer connections and implementation Water connection 3 4 Indicator light connection Pneumatic Kit Optional Din connector for the control panel Roma and Roma Il Optional and the Split Box Optional Main switch Power supply Connection for pneumatic remote control Pneumatic Kit Optional Connecting the remote control button Optional Pneumatic Kit The remote control button functions pneumatically on air pressure Connect the black air tube found in the accessory packet as shown in the figure The tube must be straight Cut the tube to suitable length The push button may be installed either inside or outside the steam room Clear silicone can be used for mounting Push button is not needed if the unit is controlled with a control centre Roma or Roma Il Be sure to leave the switch on ON position if the remote control button is not used removed Connecti
16. steamer is very easy By using the citric acid recommended by Helo the procedure is safe HNS M steamer s lid is equipped with a filling tube for deliming agent which makes it easy to add the agent into the tank HLS steamer must be equipped with a separate Descale Kit to get the agent into the tank Descale Kit is installed on the steam pipe before the relief valve How to decalcify Add 50g citric acid one bag to 1 litre water and mix let the agent dissolve into the water Lift the plastic cover off the steamer and open the filling pipe cap Pour the solution into the tank use a funnel if necessary and close the cap Start the steamer as usual and let the water boil for about 10 minutes After the water has boiled enough stop the steamer and follow these instructions e Automatic flush valve The steamer flushes and rinses itself 15 minutes after it has been stopped After the first flushing the steamer is restarted and the tank is allowed to fill up with water after which the steamer is stopped again and allowed to flush and rinse again after 15 minutes This can be repeated about 3 to 5 times If HSX L is equipped with an automatic flush valve install the manual flush valve found in the original packaging temporarily in the unit and rinse the unit according to the manual flushing instructions e Manual flush valve After boiling let the citric acid solution act in the tank for 15 minutes and flush the tank afte
17. valve 4 Heating the water takes about 5 to 10 minutes depending on the power output after which steam generation starts 5 Steamer is stopped by pressing the pneumatic push button again or if a timer is used after the time has run out Timer circuit 25 min or Roma Il or by pressing the control centre switch to 0 position Roma Instructions for Use and Installation HNS M HLS Installing the Descale Kit to HLS steamer Relief valve Steam pipe to steam room Citric acid fill up valve Installed on the steam pipe as shown in the figure 13 Instructions for Use and Installation HNS M HLS 14 ROHS Ymp rist nsuojeluun liittyvia ohjeita Taman tuotteen k ytt i n p tytty sit ei saa h vitt normaalin talousj tteen mukana vaan se on toimitettava s hk ja elektroniikkalaitteiden kierr tykseen tarkoitettuun ker yspisteeseen Symboli tuotteessa k ytt ohjeessa tai pakkauksessa tarkoittaa sit Valmistusaineet ovat kierr tett viss merkint ns mukaan K ytettyjen laitteiden uudelleenk yt ll materiaalien hyd ynt misell tai muulla uudelleenk yt ll teet arvokkaan teon ymp rist mme hyv ksi Tuote palautetaan ilman kiuaskivi ja verhouskivi kierr tyskeskukseen Tietoa kierr tyspaikoista saat kuntasi palvelupisteest Instructions for environmental protection This product must not be disposed with normal household waste at the end of its life cycle Instead
18. weighs about 17 kg when filled with water When the automatic drain valve is used it is recommended you use wall installation so an adequate angle can be ensured for draining of water Image of principle of installation Control panel Water connection O 400V 3N Flushing Locating the control panel Steamer wall mounting The control panel may also be installed in the steam room model HNS M HSX L Roma centre is only to be installed outside the steam room NOTE The RA 17 control panel has a built in thermostat If an external thermostat is used the cable is connected to steamer circuit board in model HNS M In other models the thermostat cable is connected to the control centre model HLS Roma and Roma II The cable can be extended with a similar cable also for control panel max 10m Steam nozzle nozzles are fitted approximately 200 400mm from the floor underneath a bench or a seat or onto the wall so that the hot steam cannot burn anyone s feet The steam nozzles are aimed towards the floor When the nozzles are installed you must ensure to place them somewhere where nobody can accidentally touch them The steam temperature is 100 C and it can cause injuries on contact The thermostat is installed at about 1700mm height preferably on the wall opposite the door It is recommended to seal the thermostat installation hole with appropriate sealing material so that moisture cannot enter the structures

Download Pdf Manuals

image

Related Search

Related Contents

2E16G - Jive  01977L0541-20070101  Falk Ultramite Type UCBN, UCFN, Sizes 03-14 Gear Drives    Philips Hairdryer HP8190    M177 Postoperative Care Suit  GARANTIE 25 ANS  Shure Microphone SM80 User's Manual  OM, Flymo, Visimo, Easimo, 964322062, 9634322162, 964322222  

Copyright © All rights reserved.
Failed to retrieve file